diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power/reset')
5 files changed, 153 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt new file mode 100644 index 000000000..c82f12e2d --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt @@ -0,0 +1,67 @@ +* Device tree bindings for Texas Instruments keystone reset + +This node is intended to allow SoC reset in case of software reset +of selected watchdogs. + +The Keystone SoCs can contain up to 4 watchdog timers to reset +SoC. Each watchdog timer event input is connected to the Reset Mux +block. The Reset Mux block can be configured to cause reset or not. + +Additionally soft or hard reset can be configured. + +Required properties: + +- compatible: ti,keystone-reset + +- ti,syscon-pll: phandle/offset pair. The phandle to syscon used to + access pll controller registers and the offset to use + reset control registers. + +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset + in order to use mux block registers for all watchdogs. + +Optional properties: + +- ti,soft-reset: Boolean option indicating soft reset. + By default hard reset is used. + +- ti,wdt-list: WDT list that can cause SoC reset. It's not related + to WDT driver, it's just needed to enable a SoC related + reset that's triggered by one of WDTs. The list is + in format: <0>, <2>; It can be in random order and + begins from 0 to 3, as keystone can contain up to 4 SoC + reset watchdogs and can be in random order. + +Example 1: +Setup keystone reset so that in case software reset or +WDT0 is triggered it issues hard reset for SoC. + +pllctrl: pll-controller@02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; + +devctrl: device-state-control@02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>; +}; + +Example 2: +Setup keystone reset so that in case of software reset or +WDT0 or WDT2 is triggered it issues soft reset for SoC. + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>, <2>; + ti,soft-reset; +}; diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt new file mode 100644 index 000000000..cd2d7f58a --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -0,0 +1,29 @@ +Binding for the LTC2952 PowerPath controller + +This chip is used to externally trigger a system shut down. Once the trigger has +been sent, the chip's watchdog has to be reset to gracefully shut down. +A full powerdown can be triggered via the kill signal. + +Required properties: + +- compatible: Must contain: "lltc,ltc2952" +- watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's watchdog line +- kill-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's kill line + +Optional properties: +- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's trigger line. If this property is not set, the + trigger function is ignored and the chip is kept alive + until an explicit kill signal is received + +Example: + +ltc2952 { + compatible = "lltc,ltc2952"; + + trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt new file mode 100644 index 000000000..809af54f0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -0,0 +1,11 @@ +*Device-Tree bindings for ST SW reset functionality + +Required properties: +- compatible: should be "st,<chip>-restart". +- st,syscfg: should be a phandle of the syscfg node. + +Example node: + restart { + compatible = "st,stih416-restart"; + st,syscfg = <&syscfg_sbc>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt new file mode 100644 index 000000000..1e2546f8b --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt @@ -0,0 +1,23 @@ +Generic SYSCON mapped register poweroff driver + +This is a generic poweroff driver using syscon to map the poweroff register. +The poweroff is generally performed with a write to the poweroff register +defined by the register map pointed by syscon reference plus the offset +with the mask defined in the poweroff node. + +Required properties: +- compatible: should contain "syscon-poweroff" +- regmap: this is phandle to the register map node +- offset: offset in the register map for the poweroff register (in bytes) +- mask: the poweroff value written to the poweroff register (32 bit access) + +Default will be little endian mode, 32 bit access only. + +Examples: + + poweroff { + compatible = "syscon-poweroff"; + regmap = <®mapnode>; + offset = <0x0>; + mask = <0x7a>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt new file mode 100644 index 000000000..11906316b --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt @@ -0,0 +1,23 @@ +Generic SYSCON mapped register reset driver + +This is a generic reset driver using syscon to map the reset register. +The reset is generally performed with a write to the reset register +defined by the register map pointed by syscon reference plus the offset +with the mask defined in the reboot node. + +Required properties: +- compatible: should contain "syscon-reboot" +- regmap: this is phandle to the register map node +- offset: offset in the register map for the reboot register (in bytes) +- mask: the reset value written to the reboot register (32 bit access) + +Default will be little endian mode, 32 bit access only. + +Examples: + + reboot { + compatible = "syscon-reboot"; + regmap = <®mapnode>; + offset = <0x0>; + mask = <0x1>; + }; |