diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power')
5 files changed, 569 insertions, 4 deletions
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt new file mode 100644 index 000000000..5c9d3940d --- /dev/null +++ b/Documentation/devicetree/bindings/power/bq24257.txt @@ -0,0 +1,21 @@ +Binding for TI bq24257 Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24257" +- reg: integer, i2c address of the device. +- ti,battery-regulation-voltage: integer, maximum charging voltage in uV. +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Example: + +bq24257 { + compatible = "ti,bq24257"; + reg = <0x6a>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; +}; diff --git a/Documentation/devicetree/bindings/power/bq25890.txt b/Documentation/devicetree/bindings/power/bq25890.txt new file mode 100644 index 000000000..c9dd17d14 --- /dev/null +++ b/Documentation/devicetree/bindings/power/bq25890.txt @@ -0,0 +1,46 @@ +Binding for TI bq25890 Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq25890" +- reg: integer, i2c address of the device. +- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV); +- ti,charge-current: integer, maximum charging current (in uA); +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA); +- ti,precharge-current: integer, maximum charge current during precharge + phase (in uA); +- ti,minimum-sys-voltage: integer, when battery is charging and it is below + minimum system voltage, the system will be regulated above + minimum-sys-voltage setting (in uV); +- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV); +- ti,boost-max-current: integer, maximum allowed current draw in boost mode + (in uA). + +Optional properties: +- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz, + otherwise 1.5MHz; +- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the + input current will be the lower between the resistor setting and the IINLIM + register setting; +- ti,thermal-regulation-threshold: integer, temperature above which the charge + current is lowered, to avoid overheating (in degrees Celsius). If omitted, + the default setting will be used (120 degrees); + +Example: + +bq25890 { + compatible = "ti,bq25890"; + reg = <0x6a>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + ti,precharge-current = <128000>; + ti,minimum-sys-voltage = <3600000>; + ti,boost-voltage = <5000000>; + ti,boost-max-current = <1000000>; + + ti,use-ilim-pin; + ti,thermal-regulation-threshold = <120>; +}; diff --git a/Documentation/devicetree/bindings/power/opp.txt b/Documentation/devicetree/bindings/power/opp.txt index 74499e503..0d5e7c978 100644 --- a/Documentation/devicetree/bindings/power/opp.txt +++ b/Documentation/devicetree/bindings/power/opp.txt @@ -1,8 +1,19 @@ -* Generic OPP Interface +Generic OPP (Operating Performance Points) Bindings +---------------------------------------------------- -SoCs have a standard set of tuples consisting of frequency and -voltage pairs that the device will support per voltage domain. These -are called Operating Performance Points or OPPs. +Devices work at voltage-current-frequency combinations and some implementations +have the liberty of choosing these. These combinations are called Operating +Performance Points aka OPPs. This document defines bindings for these OPPs +applicable across wide range of devices. For illustration purpose, this document +uses CPU as a device. + +This document contain multiple versions of OPP binding and only one of them +should be used per device. + +Binding 1: operating-points +============================ + +This binding only supports voltage-frequency pairs. Properties: - operating-points: An array of 2-tuples items, and each item consists @@ -23,3 +34,432 @@ cpu@0 { 198000 850000 >; }; + + +Binding 2: operating-points-v2 +============================ + +* Property: operating-points-v2 + +Devices supporting OPPs must set their "operating-points-v2" property with +phandle to a OPP table in their DT node. The OPP core will use this phandle to +find the operating points for the device. + +Devices may want to choose OPP tables at runtime and so can provide a list of +phandles here. But only *one* of them should be chosen at runtime. This must be +accompanied by a corresponding "operating-points-names" property, to uniquely +identify the OPP tables. + +If required, this can be extended for SoC vendor specfic bindings. Such bindings +should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt +and should have a compatible description like: "operating-points-v2-<vendor>". + +Optional properties: +- operating-points-names: Names of OPP tables (required if multiple OPP + tables are present), to uniquely identify them. The same list must be present + for all the CPUs which are sharing clock/voltage rails and hence the OPP + tables. + +* OPP Table Node + +This describes the OPPs belonging to a device. This node can have following +properties: + +Required properties: +- compatible: Allow OPPs to express their compatibility. It should be: + "operating-points-v2". + +- OPP nodes: One or more OPP nodes describing voltage-current-frequency + combinations. Their name isn't significant but their phandle can be used to + reference an OPP. + +Optional properties: +- opp-shared: Indicates that device nodes using this OPP Table Node's phandle + switch their DVFS state together, i.e. they share clock/voltage/current lines. + Missing property means devices have independent clock/voltage/current lines, + but they share OPP tables. + +- status: Marks the OPP table enabled/disabled. + + +* OPP Node + +This defines voltage-current-frequency combinations along with other related +properties. + +Required properties: +- opp-hz: Frequency in Hz + +Optional properties: +- opp-microvolt: voltage in micro Volts. + + A single regulator's voltage is specified with an array of size one or three. + Single entry is for target voltage and three entries are for <target min max> + voltages. + + Entries for multiple regulators must be present in the same order as + regulators are specified in device's DT node. + +- opp-microamp: The maximum current drawn by the device in microamperes + considering system specific parameters (such as transients, process, aging, + maximum operating temperature range etc.) as necessary. This may be used to + set the most efficient regulator operating mode. + + Should only be set if opp-microvolt is set for the OPP. + + Entries for multiple regulators must be present in the same order as + regulators are specified in device's DT node. If this property isn't required + for few regulators, then this should be marked as zero for them. If it isn't + required for any regulator, then this property need not be present. + +- clock-latency-ns: Specifies the maximum possible transition latency (in + nanoseconds) for switching to this OPP from any other OPP. + +- turbo-mode: Marks the OPP to be used only for turbo modes. Turbo mode is + available on some platforms, where the device can run over its operating + frequency for a short duration of time limited by the device's power, current + and thermal limits. + +- opp-suspend: Marks the OPP to be used during device suspend. Only one OPP in + the table should have this. + +- status: Marks the node enabled/disabled. + +Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a9"; + reg = <0>; + next-level-cache = <&L2>; + clocks = <&clk_controller 0>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply0>; + operating-points-v2 = <&cpu0_opp_table>; + }; + + cpu@1 { + compatible = "arm,cortex-a9"; + reg = <1>; + next-level-cache = <&L2>; + clocks = <&clk_controller 0>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply0>; + operating-points-v2 = <&cpu0_opp_table>; + }; + }; + + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000 975000 985000>; + opp-microamp = <70000>; + clock-latency-ns = <300000>; + opp-suspend; + }; + opp01 { + opp-hz = <1100000000>; + opp-microvolt = <980000 1000000 1010000>; + opp-microamp = <80000>; + clock-latency-ns = <310000>; + }; + opp02 { + opp-hz = <1200000000>; + opp-microvolt = <1025000>; + clock-latency-ns = <290000>; + turbo-mode; + }; + }; +}; + +Example 2: Single cluster, Quad-core Qualcom-krait, switches DVFS states +independently. + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "qcom,krait"; + reg = <0>; + next-level-cache = <&L2>; + clocks = <&clk_controller 0>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply0>; + operating-points-v2 = <&cpu_opp_table>; + }; + + cpu@1 { + compatible = "qcom,krait"; + reg = <1>; + next-level-cache = <&L2>; + clocks = <&clk_controller 1>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply1>; + operating-points-v2 = <&cpu_opp_table>; + }; + + cpu@2 { + compatible = "qcom,krait"; + reg = <2>; + next-level-cache = <&L2>; + clocks = <&clk_controller 2>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply2>; + operating-points-v2 = <&cpu_opp_table>; + }; + + cpu@3 { + compatible = "qcom,krait"; + reg = <3>; + next-level-cache = <&L2>; + clocks = <&clk_controller 3>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply3>; + operating-points-v2 = <&cpu_opp_table>; + }; + }; + + cpu_opp_table: opp_table { + compatible = "operating-points-v2"; + + /* + * Missing opp-shared property means CPUs switch DVFS states + * independently. + */ + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000 975000 985000>; + opp-microamp = <70000>; + clock-latency-ns = <300000>; + opp-suspend; + }; + opp01 { + opp-hz = <1100000000>; + opp-microvolt = <980000 1000000 1010000>; + opp-microamp = <80000>; + clock-latency-ns = <310000>; + }; + opp02 { + opp-hz = <1200000000>; + opp-microvolt = <1025000>; + opp-microamp = <90000; + lock-latency-ns = <290000>; + turbo-mode; + }; + }; +}; + +Example 3: Dual-cluster, Dual-core per cluster. CPUs within a cluster switch +DVFS state together. + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a7"; + reg = <0>; + next-level-cache = <&L2>; + clocks = <&clk_controller 0>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply0>; + operating-points-v2 = <&cluster0_opp>; + }; + + cpu@1 { + compatible = "arm,cortex-a7"; + reg = <1>; + next-level-cache = <&L2>; + clocks = <&clk_controller 0>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply0>; + operating-points-v2 = <&cluster0_opp>; + }; + + cpu@100 { + compatible = "arm,cortex-a15"; + reg = <100>; + next-level-cache = <&L2>; + clocks = <&clk_controller 1>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply1>; + operating-points-v2 = <&cluster1_opp>; + }; + + cpu@101 { + compatible = "arm,cortex-a15"; + reg = <101>; + next-level-cache = <&L2>; + clocks = <&clk_controller 1>; + clock-names = "cpu"; + cpu-supply = <&cpu_supply1>; + operating-points-v2 = <&cluster1_opp>; + }; + }; + + cluster0_opp: opp_table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000 975000 985000>; + opp-microamp = <70000>; + clock-latency-ns = <300000>; + opp-suspend; + }; + opp01 { + opp-hz = <1100000000>; + opp-microvolt = <980000 1000000 1010000>; + opp-microamp = <80000>; + clock-latency-ns = <310000>; + }; + opp02 { + opp-hz = <1200000000>; + opp-microvolt = <1025000>; + opp-microamp = <90000>; + clock-latency-ns = <290000>; + turbo-mode; + }; + }; + + cluster1_opp: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp10 { + opp-hz = <1300000000>; + opp-microvolt = <1045000 1050000 1055000>; + opp-microamp = <95000>; + clock-latency-ns = <400000>; + opp-suspend; + }; + opp11 { + opp-hz = <1400000000>; + opp-microvolt = <1075000>; + opp-microamp = <100000>; + clock-latency-ns = <400000>; + }; + opp12 { + opp-hz = <1500000000>; + opp-microvolt = <1010000 1100000 1110000>; + opp-microamp = <95000>; + clock-latency-ns = <400000>; + turbo-mode; + }; + }; +}; + +Example 4: Handling multiple regulators + +/ { + cpus { + cpu@0 { + compatible = "arm,cortex-a7"; + ... + + cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>; + operating-points-v2 = <&cpu0_opp_table>; + }; + }; + + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000>, /* Supply 0 */ + <960000>, /* Supply 1 */ + <960000>; /* Supply 2 */ + opp-microamp = <70000>, /* Supply 0 */ + <70000>, /* Supply 1 */ + <70000>; /* Supply 2 */ + clock-latency-ns = <300000>; + }; + + /* OR */ + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000 975000 985000>, /* Supply 0 */ + <960000 965000 975000>, /* Supply 1 */ + <960000 965000 975000>; /* Supply 2 */ + opp-microamp = <70000>, /* Supply 0 */ + <70000>, /* Supply 1 */ + <70000>; /* Supply 2 */ + clock-latency-ns = <300000>; + }; + + /* OR */ + + opp00 { + opp-hz = <1000000000>; + opp-microvolt = <970000 975000 985000>, /* Supply 0 */ + <960000 965000 975000>, /* Supply 1 */ + <960000 965000 975000>; /* Supply 2 */ + opp-microamp = <70000>, /* Supply 0 */ + <0>, /* Supply 1 doesn't need this */ + <70000>; /* Supply 2 */ + clock-latency-ns = <300000>; + }; + }; +}; + +Example 5: Multiple OPP tables + +/ { + cpus { + cpu@0 { + compatible = "arm,cortex-a7"; + ... + + cpu-supply = <&cpu_supply> + operating-points-v2 = <&cpu0_opp_table_slow>, <&cpu0_opp_table_fast>; + operating-points-names = "slow", "fast"; + }; + }; + + cpu0_opp_table_slow: opp_table_slow { + compatible = "operating-points-v2"; + status = "okay"; + opp-shared; + + opp00 { + opp-hz = <600000000>; + ... + }; + + opp01 { + opp-hz = <800000000>; + ... + }; + }; + + cpu0_opp_table_fast: opp_table_fast { + compatible = "operating-points-v2"; + status = "okay"; + opp-shared; + + opp10 { + opp-hz = <1000000000>; + ... + }; + + opp11 { + opp-hz = <1100000000>; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/power/rt9455_charger.txt b/Documentation/devicetree/bindings/power/rt9455_charger.txt new file mode 100644 index 000000000..5d9ad5cf2 --- /dev/null +++ b/Documentation/devicetree/bindings/power/rt9455_charger.txt @@ -0,0 +1,48 @@ +Binding for Richtek rt9455 battery charger + +Required properties: +- compatible: it should contain one of the following: + "richtek,rt9455". +- reg: integer, i2c address of the device. +- interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. +- interrupts: interrupt mapping for GPIO IRQ, it should be + configured with IRQ_TYPE_LEVEL_LOW flag. +- richtek,output-charge-current: integer, output current from the charger to the + battery, in uA. +- richtek,end-of-charge-percentage: integer, percent of the output charge current. + When the current in constant-voltage phase drops + below output_charge_current x end-of-charge-percentage, + charge is terminated. +- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV. +- richtek,boost-output-voltage: integer, maximum voltage provided to consumer + devices, when the charger is in boost mode, in uV. + +Optional properties: +- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to + decrease voltage level when the over current + of the input power source occurs. + This prevents input voltage drop due to insufficient + current provided by the power source. + Default: 4500000 uV (4.5V) +- richtek,avg-input-current-regulation: integer, input current value in uA drained by the + charger from the power source. + Default: 500000 uA (500mA) + +Example: + +rt9455@22 { + compatible = "richtek,rt9455"; + reg = <0x22>; + + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + richtek,output-charge-current = <500000>; + richtek,end-of-charge-percentage = <10>; + richtek,battery-regulation-voltage = <4200000>; + richtek,boost-output-voltage = <5050000>; + + richtek,min-input-voltage-regulation = <4500000>; + richtek,avg-input-current-regulation = <500000>; +}; diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt index d5c706216..3b4ea1b73 100644 --- a/Documentation/devicetree/bindings/power/twl-charger.txt +++ b/Documentation/devicetree/bindings/power/twl-charger.txt @@ -1,5 +1,15 @@ TWL BCI (Battery Charger Interface) +The battery charger needs to interact with the USB phy in order +to know when charging is permissible, and when there is a connection +or disconnection. + +The choice of phy cannot be configured at a hardware level, so there +is no value in explicit configuration in device-tree. Rather +if there is a sibling of the BCI node which is compatible with +"ti,twl4030-usb", then that is used to determine when and how +use USB power for charging. + Required properties: - compatible: - "ti,twl4030-bci" |