diff options
Diffstat (limited to 'Documentation/devicetree/bindings/serial/atmel-usart.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/serial/atmel-usart.txt | 60 |
1 files changed, 60 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt new file mode 100644 index 000000000..90787aa2e --- /dev/null +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -0,0 +1,60 @@ +* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +Required properties: +- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu" + The compatible <chip> indicated will be the first SoC to support an + additional mode or an USART new feature. + For the dbgu UART, use "atmel,<chip>-dbgu", "atmel,<chip>-usart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt +- clock-names: tuple listing input clock names. + Required elements: "usart" +- clocks: phandles to input clocks. + +Optional properties: +- atmel,use-dma-rx: use of PDC or DMA for receiving data +- atmel,use-dma-tx: use of PDC or DMA for transmitting data +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. + It will use specified PIO instead of the peripheral function pin for the USART feature. + If unsure, don't specify this property. +- add dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "rx" for RX channel, "tx" for TX channel. + +<chip> compatible description: +- at91rm9200: legacy USART support +- at91sam9260: generic USART implementation for SAM9 SoCs + +Example: +- use PDC: + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + clocks = <&usart0_clk>; + clock-names = "usart"; + atmel,use-dma-rx; + atmel,use-dma-tx; + rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>; + }; + +- use DMA: + usart0: serial@f001c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf001c000 0x100>; + interrupts = <12 4 5>; + clocks = <&usart0_clk>; + clock-names = "usart"; + atmel,use-dma-rx; + atmel,use-dma-tx; + dmas = <&dma0 2 0x3>, + <&dma0 2 0x204>; + dma-names = "tx", "rx"; + }; |