diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
4 files changed, 64 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt new file mode 100644 index 000000000..79de379f4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt @@ -0,0 +1,34 @@ +Microchip PIC32 SPI Master controller + +Required properties: +- compatible: Should be "microchip,pic32mzda-spi". +- reg: Address and length of register space for the device. +- interrupts: Should contain all three spi interrupts in sequence + of <fault-irq>, <receive-irq>, <transmit-irq>. +- interrupt-names: Should be "fault", "rx", "tx" in order. +- clocks: Phandle of the clock generating SPI clock on the bus. +- clock-names: Should be "mck0". +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- dmas: Two or more DMA channel specifiers following the convention outlined + in Documentation/devicetree/bindings/dma/dma.txt +- dma-names: Names for the dma channels. There must be at least one channel + named "spi-tx" for transmit and named "spi-rx" for receive. + +Example: + +spi1: spi@1f821000 { + compatible = "microchip,pic32mzda-spi"; + reg = <0x1f821000 0x200>; + interrupts = <109 IRQ_TYPE_LEVEL_HIGH>, + <110 IRQ_TYPE_LEVEL_HIGH>, + <111 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fault", "rx", "tx"; + clocks = <&PBCLK2>; + clock-names = "mck0"; + cs-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + dmas = <&dma 134>, <&dma 135>; + dma-names = "spi-rx", "spi-tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index fa77f874e..ff5893d27 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -1,7 +1,10 @@ ARM Freescale DSPI controller Required properties: -- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", "fsl,ls2085a-dspi" +- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", + "fsl,ls2085a-dspi" + or + "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. @@ -13,8 +16,7 @@ Required properties: Optional property: - big-endian: If present the dspi device's registers are implemented - in big endian mode, otherwise in native mode(same with CPU), for more - detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + in big endian mode. Optional SPI slave node properties: - fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip diff --git a/Documentation/devicetree/bindings/spi/sqi-pic32.txt b/Documentation/devicetree/bindings/spi/sqi-pic32.txt new file mode 100644 index 000000000..c82d021bc --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sqi-pic32.txt @@ -0,0 +1,18 @@ +Microchip PIC32 Quad SPI controller +----------------------------------- +Required properties: +- compatible: Should be "microchip,pic32mzda-sqi". +- reg: Address and length of SQI controller register space. +- interrupts: Should contain SQI interrupt. +- clocks: Should contain phandle of two clocks in sequence, one that drives + clock on SPI bus and other that drives SQI controller. +- clock-names: Should be "spi_ck" and "reg_ck" in order. + +Example: + sqi1: spi@1f8e2000 { + compatible = "microchip,pic32mzda-sqi"; + reg = <0x1f8e2000 0x200>; + clocks = <&rootclk REF2CLK>, <&rootclk PB5CLK>; + clock-names = "spi_ck", "reg_ck"; + interrupts = <169 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index cc8304aa6..50b14f6b5 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -19,6 +19,13 @@ Optional properties: - syscon-chipselects: Handle to system control region contains QSPI chipselect register and offset of that register. +NOTE: TI QSPI controller requires different pinmux and IODelay +paramaters for Mode-0 and Mode-3 operations, which needs to be set up by +the bootloader (U-Boot). Default configuration only supports Mode-0 +operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be +specified in the slave nodes of TI QSPI controller without appropriate +modification to bootloader. + Example: For am4372: |