summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/spmi
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/spmi')
-rw-r--r--Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt65
-rw-r--r--Documentation/devicetree/bindings/spmi/spmi.txt41
2 files changed, 106 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
new file mode 100644
index 000000000..e16b9b5af
--- /dev/null
+++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
@@ -0,0 +1,65 @@
+Qualcomm SPMI Controller (PMIC Arbiter)
+
+The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI
+controller with wrapping arbitration logic to allow for multiple on-chip
+devices to control a single SPMI master.
+
+The PMIC Arbiter can also act as an interrupt controller, providing interrupts
+to slave devices.
+
+See spmi.txt for the generic SPMI controller binding requirements for child
+nodes.
+
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+generic interrupt controller binding documentation.
+
+Required properties:
+- compatible : should be "qcom,spmi-pmic-arb".
+- reg-names : must contain:
+ "core" - core registers
+ "intr" - interrupt controller registers
+ "cnfg" - configuration registers
+ Registers used only for V2 PMIC Arbiter:
+ "chnls" - tx-channel per virtual slave registers.
+ "obsrvr" - rx-channel (called observer) per virtual slave registers.
+
+- reg : address + size pairs describing the PMIC arb register sets; order must
+ correspond with the order of entries in reg-names
+- #address-cells : must be set to 2
+- #size-cells : must be set to 0
+- qcom,ee : indicates the active Execution Environment identifier (0-5)
+- qcom,channel : which of the PMIC Arb provided channels to use for accesses (0-5)
+- interrupts : interrupt list for the PMIC Arb controller, must contain a
+ single interrupt entry for the peripheral interrupt
+- interrupt-names : corresponding interrupt names for the interrupts
+ listed in the 'interrupts' property, must contain:
+ "periph_irq" - summary interrupt for PMIC peripherals
+- interrupt-controller : boolean indicator that the PMIC arbiter is an interrupt controller
+- #interrupt-cells : must be set to 4. Interrupts are specified as a 4-tuple:
+ cell 1: slave ID for the requested interrupt (0-15)
+ cell 2: peripheral ID for requested interrupt (0-255)
+ cell 3: the requested peripheral interrupt (0-7)
+ cell 4: interrupt flags indicating level-sense information, as defined in
+ dt-bindings/interrupt-controller/irq.h
+
+Example:
+
+ spmi {
+ compatible = "qcom,spmi-pmic-arb";
+ reg-names = "core", "intr", "cnfg";
+ reg = <0xfc4cf000 0x1000>,
+ <0xfc4cb000 0x1000>,
+ <0xfc4ca000 0x1000>;
+
+ interrupt-names = "periph_irq";
+ interrupts = <0 190 0>;
+
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
diff --git a/Documentation/devicetree/bindings/spmi/spmi.txt b/Documentation/devicetree/bindings/spmi/spmi.txt
new file mode 100644
index 000000000..4bb10d161
--- /dev/null
+++ b/Documentation/devicetree/bindings/spmi/spmi.txt
@@ -0,0 +1,41 @@
+System Power Management Interface (SPMI) Controller
+
+This document defines a generic set of bindings for use by SPMI controllers. A
+controller is modelled in device tree as a node with zero or more child nodes,
+each representing a unique slave on the bus.
+
+Required properties:
+- #address-cells : must be set to 2
+- #size-cells : must be set to 0
+
+Child nodes:
+
+An SPMI controller node can contain zero or more child nodes representing slave
+devices on the bus. Child 'reg' properties are specified as an address, type
+pair. The address must be in the range 0-15 (4 bits). The type must be one of
+SPMI_USID (0) or SPMI_GSID (1) for Unique Slave ID or Group Slave ID respectively.
+These are the identifiers "statically assigned by the system integrator", as
+per the SPMI spec.
+
+Each child node must have one and only one 'reg' entry of type SPMI_USID.
+
+#include <dt-bindings/spmi/spmi.h>
+
+ spmi@.. {
+ compatible = "...";
+ reg = <...>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ child@0 {
+ compatible = "...";
+ reg = <0 SPMI_USID>;
+ };
+
+ child@7 {
+ compatible = "...";
+ reg = <7 SPMI_USID
+ 3 SPMI_GSID>;
+ };
+ };