diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
7 files changed, 148 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt new file mode 100644 index 000000000..862cd7c79 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt @@ -0,0 +1,29 @@ +Allwinner sun4i A10 musb DRC/OTG controller +------------------------------------------- + +Required properties: + - compatible : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb" + or "allwinner,sun8i-a33-musb" + - reg : mmio address range of the musb controller + - clocks : clock specifier for the musb controller ahb gate clock + - reset : reset specifier for the ahb reset (A31 and newer only) + - interrupts : interrupt to which the musb controller is connected + - interrupt-names : must be "mc" + - phys : phy specifier for the otg phy + - phy-names : must be "usb" + - dr_mode : Dual-Role mode must be "host" or "otg" + - extcon : extcon specifier for the otg phy + +Example: + + usb_otg: usb@01c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <38>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 553e2fae3..a057b75ba 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -6,6 +6,7 @@ Required properties: "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" + "xlnx,zynq-usb-2.20a" - reg: base address and length of the registers - interrupts: interrupt for the USB controller @@ -30,6 +31,21 @@ Optional properties: argument that indicate usb controller index - disable-over-current: (FSL only) disable over current detect - external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus +- itc-setting: interrupt threshold control register control, the setting + should be aligned with ITC bits at register USBCMD. +- ahb-burst-config: it is vendor dependent, the required value should be + aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This + property is used to change AHB burst configuration, check the chipidea + spec for meaning of each value. If this property is not existed, it + will use the reset value. +- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from system memory to the USB + bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0. +- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from the USB bus to system memory, + changing this value takes effect only the SBUSCFG.AHBBRST is 0. Example: @@ -41,4 +57,9 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; + gadget-itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0815eac5b..e12f34488 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -35,6 +35,8 @@ Optional properties: LTSSM during USB3 Compliance mode. - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index 477d5bb5e..bba825711 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -11,6 +11,19 @@ Optional properties: "peripheral" and "otg". In case this attribute isn't passed via DT, USB DRD controllers should default to OTG. + - otg-rev: tells usb driver the release number of the OTG and EH supplement + with which the device and its descriptors are compliant, + in binary-coded decimal (i.e. 2.0 is 0200H). This + property is used if any real OTG features(HNP/SRP/ADP) + is enabled, if ADP is required, otg-rev should be + 0x0200 or above. + - hnp-disable: tells OTG controllers we want to disable OTG HNP, normally HNP + is the basic function of real OTG except you want it + to be a srp-capable only B device. + - srp-disable: tells OTG controllers we want to disable OTG SRP, SRP is + optional for OTG device. + - adp-disable: tells OTG controllers we want to disable OTG ADP, ADP is + optional for OTG device. This is an attribute to a USB controller such as: @@ -21,4 +34,6 @@ dwc3@4a030000 { usb-phy = <&usb2_phy>, <&usb3,phy>; maximum-speed = "super-speed"; dr_mode = "otg"; + otg-rev = <0x0200>; + adp-disable; }; diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index bd8d9e753..8654a3ec2 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -52,6 +52,10 @@ Required properties: Optional properties: - dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" +- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual + SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex + D+/D- USB lines between connectors. + - qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device Mode Eye Diagram test. Start address at which these values will be written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as diff --git a/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt new file mode 100644 index 000000000..2cb2168ce --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt @@ -0,0 +1,76 @@ +Qualcomm's APQ8016/MSM8916 USB transceiver controller + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-8x16-phy". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: USB PHY base address and length of the register map + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: See clock-bindings.txt section "consumers". List of + two clock specifiers for interface and core controller + clocks. + +- clock-names: + Usage: required + Value type: <string> + Definition: Must contain "iface" and "core" strings. + +- vddcx-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator VDCCX supply node. + +- v1p8-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 1.8V supply node. + +- v3p3-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 3.3V supply node. + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: See reset.txt section "consumers". PHY reset specifier. + +- reset-names: + Usage: required + Value type: <string> + Definition: Must contain "phy" string. + +- switch-gpio: + Usage: optional + Value type: <prop-encoded-array> + Definition: Some boards are using Dual SPDT USB Switch, witch is + controlled by GPIO to de/multiplex D+/D- USB lines + between connectors. + +Example: + usb_phy: phy@78d9000 { + compatible = "qcom,usb-8x16-phy"; + reg = <0x78d9000 0x400>; + + vddcx-supply = <&pm8916_s1_corner>; + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + + clocks = <&gcc GCC_USB_HS_AHB_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + + resets = <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy"; + + // D+/D- lines: 1 - Routed to HUB, 0 - Device connector + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + }; + diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 64a4ca6cf..7d48f63db 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" - "renesas,usbhs-r8a7794" + - "renesas,usbhs-r8a7795" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs |