diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video/arm,pl11x.txt')
-rw-r--r-- | Documentation/devicetree/bindings/video/arm,pl11x.txt | 109 |
1 files changed, 0 insertions, 109 deletions
diff --git a/Documentation/devicetree/bindings/video/arm,pl11x.txt b/Documentation/devicetree/bindings/video/arm,pl11x.txt deleted file mode 100644 index 3e3039a8a..000000000 --- a/Documentation/devicetree/bindings/video/arm,pl11x.txt +++ /dev/null @@ -1,109 +0,0 @@ -* ARM PrimeCell Color LCD Controller PL110/PL111 - -See also Documentation/devicetree/bindings/arm/primecell.txt - -Required properties: - -- compatible: must be one of: - "arm,pl110", "arm,primecell" - "arm,pl111", "arm,primecell" - -- reg: base address and size of the control registers block - -- interrupt-names: either the single entry "combined" representing a - combined interrupt output (CLCDINTR), or the four entries - "mbe", "vcomp", "lnbu", "fuf" representing the individual - CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts - -- interrupts: contains an interrupt specifier for each entry in - interrupt-names - -- clock-names: should contain "clcdclk" and "apb_pclk" - -- clocks: contains phandle and clock specifier pairs for the entries - in the clock-names property. See - Documentation/devicetree/binding/clock/clock-bindings.txt - -Optional properties: - -- memory-region: phandle to a node describing memory (see - Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) - to be used for the framebuffer; if not present, the framebuffer - may be located anywhere in the memory - -- max-memory-bandwidth: maximum bandwidth in bytes per second that the - cell's memory interface can handle; if not present, the memory - interface is fast enough to handle all possible video modes - -Required sub-nodes: - -- port: describes LCD panel signals, following the common binding - for video transmitter interfaces; see - Documentation/devicetree/bindings/media/video-interfaces.txt; - when it is a TFT panel, the port's endpoint must define the - following property: - - - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values, - defining the way CLD pads are wired up; first value - contains index of the "CLD" external pin (pad) used - as R0 (first bit of the red component), second value - index of the pad used as G0, third value index of the - pad used as B0, see also "LCD panel signal multiplexing - details" paragraphs in the PL110/PL111 Technical - Reference Manuals; this implicitly defines available - color modes, for example: - - PL111 TFT 4:4:4 panel: - arm,pl11x,tft-r0g0b0-pads = <4 15 20>; - - PL110 TFT (1:)5:5:5 panel: - arm,pl11x,tft-r0g0b0-pads = <1 7 13>; - - PL111 TFT (1:)5:5:5 panel: - arm,pl11x,tft-r0g0b0-pads = <3 11 19>; - - PL111 TFT 5:6:5 panel: - arm,pl11x,tft-r0g0b0-pads = <3 10 19>; - - PL110 and PL111 TFT 8:8:8 panel: - arm,pl11x,tft-r0g0b0-pads = <0 8 16>; - - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped: - arm,pl11x,tft-r0g0b0-pads = <16 8 0>; - - -Example: - - clcd@10020000 { - compatible = "arm,pl111", "arm,primecell"; - reg = <0x10020000 0x1000>; - interrupt-names = "combined"; - interrupts = <0 44 4>; - clocks = <&oscclk1>, <&oscclk2>; - clock-names = "clcdclk", "apb_pclk"; - max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */ - - port { - clcd_pads: endpoint { - remote-endpoint = <&clcd_panel>; - arm,pl11x,tft-r0g0b0-pads = <0 8 16>; - }; - }; - - }; - - panel { - compatible = "panel-dpi"; - - port { - clcd_panel: endpoint { - remote-endpoint = <&clcd_pads>; - }; - }; - - panel-timing { - clock-frequency = <25175000>; - hactive = <640>; - hback-porch = <40>; - hfront-porch = <24>; - hsync-len = <96>; - vactive = <480>; - vback-porch = <32>; - vfront-porch = <11>; - vsync-len = <2>; - }; - }; |