diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video/display-timing.txt')
-rw-r--r-- | Documentation/devicetree/bindings/video/display-timing.txt | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt deleted file mode 100644 index e1d4a0b59..000000000 --- a/Documentation/devicetree/bindings/video/display-timing.txt +++ /dev/null @@ -1,110 +0,0 @@ -display-timing bindings -======================= - -display-timings node --------------------- - -required properties: - - none - -optional properties: - - native-mode: The native mode for the display, in case multiple modes are - provided. When omitted, assume the first node is the native. - -timing subnode --------------- - -required properties: - - hactive, vactive: display resolution - - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters - in pixels - vfront-porch, vback-porch, vsync-len: vertical display timing parameters in - lines - - clock-frequency: display clock in Hz - -optional properties: - - hsync-active: hsync pulse is active low/high/ignored - - vsync-active: vsync pulse is active low/high/ignored - - de-active: data-enable pulse is active low/high/ignored - - pixelclk-active: with - - active high = drive pixel data on rising edge/ - sample data on falling edge - - active low = drive pixel data on falling edge/ - sample data on rising edge - - ignored = ignored - - interlaced (bool): boolean to enable interlaced mode - - doublescan (bool): boolean to enable doublescan mode - - doubleclk (bool): boolean to enable doubleclock mode - -All the optional properties that are not bool follow the following logic: - <1>: high active - <0>: low active - omitted: not used on hardware - -There are different ways of describing the capabilities of a display. The -devicetree representation corresponds to the one commonly found in datasheets -for displays. If a display supports multiple signal timings, the native-mode -can be specified. - -The parameters are defined as: - - +----------+-------------------------------------+----------+-------+ - | | ↑ | | | - | | |vback_porch | | | - | | ↓ | | | - +----------#######################################----------+-------+ - | # ↑ # | | - | # | # | | - | hback # | # hfront | hsync | - | porch # | hactive # porch | len | - |<-------->#<-------+--------------------------->#<-------->|<----->| - | # | # | | - | # |vactive # | | - | # | # | | - | # ↓ # | | - +----------#######################################----------+-------+ - | | ↑ | | | - | | |vfront_porch | | | - | | ↓ | | | - +----------+-------------------------------------+----------+-------+ - | | ↑ | | | - | | |vsync_len | | | - | | ↓ | | | - +----------+-------------------------------------+----------+-------+ - -Example: - - display-timings { - native-mode = <&timing0>; - timing0: 1080p24 { - /* 1920x1080p24 */ - clock-frequency = <52000000>; - hactive = <1920>; - vactive = <1080>; - hfront-porch = <25>; - hback-porch = <25>; - hsync-len = <25>; - vback-porch = <2>; - vfront-porch = <2>; - vsync-len = <2>; - hsync-active = <1>; - }; - }; - -Every required property also supports the use of ranges, so the commonly used -datasheet description with minimum, typical and maximum values can be used. - -Example: - - timing1: timing { - /* 1920x1080p24 */ - clock-frequency = <148500000>; - hactive = <1920>; - vactive = <1080>; - hsync-len = <0 44 60>; - hfront-porch = <80 88 95>; - hback-porch = <100 148 160>; - vfront-porch = <0 4 6>; - vback-porch = <0 36 50>; - vsync-len = <0 5 6>; - }; |