diff options
Diffstat (limited to 'Documentation/devicetree/bindings/video/exynos_dp.txt')
-rw-r--r-- | Documentation/devicetree/bindings/video/exynos_dp.txt | 120 |
1 files changed, 0 insertions, 120 deletions
diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt deleted file mode 100644 index 7a3a9cdb8..000000000 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ /dev/null @@ -1,120 +0,0 @@ -The Exynos display port interface should be configured based on -the type of panel connected to it. - -We use two nodes: - -dp-controller node - -dptx-phy node(defined inside dp-controller node) - -For the DP-PHY initialization, we use the dptx-phy node. -Required properties for dptx-phy: deprecated, use phys and phy-names - -reg: deprecated - Base address of DP PHY register. - -samsung,enable-mask: deprecated - The bit-mask used to enable/disable DP PHY. - -For the Panel initialization, we read data from dp-controller node. -Required properties for dp-controller: - -compatible: - should be "samsung,exynos5-dp". - -reg: - physical base address of the controller and length - of memory mapped region. - -interrupts: - interrupt combiner values. - -clocks: - from common clock binding: handle to dp clock. - -clock-names: - from common clock binding: Shall be "dp". - -interrupt-parent: - phandle to Interrupt combiner node. - -phys: - from general PHY binding: the phandle for the PHY device. - -phy-names: - from general PHY binding: Should be "dp". - -samsung,color-space: - input video data format. - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 - -samsung,dynamic-range: - dynamic range for input video data. - VESA = 0, CEA = 1 - -samsung,ycbcr-coeff: - YCbCr co-efficients for input video. - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 - -samsung,color-depth: - number of bits per colour component. - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 - -samsung,link-rate: - link rate supported by the panel. - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A - -samsung,lane-count: - number of lanes supported by the panel. - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 - - display-timings: timings for the connected panel as described by - Documentation/devicetree/bindings/video/display-timing.txt - -Optional properties for dp-controller: - -interlaced: - interlace scan mode. - Progressive if defined, Interlaced if not defined - -vsync-active-high: - VSYNC polarity configuration. - High if defined, Low if not defined - -hsync-active-high: - HSYNC polarity configuration. - High if defined, Low if not defined - -samsung,hpd-gpio: - Hotplug detect GPIO. - Indicates which GPIO should be used for hotplug - detection - -video interfaces: Device node can contain video interface port - nodes according to [1]. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - -SOC specific portion: - dp-controller { - compatible = "samsung,exynos5-dp"; - reg = <0x145b0000 0x10000>; - interrupts = <10 3>; - interrupt-parent = <&combiner>; - clocks = <&clock 342>; - clock-names = "dp"; - - phys = <&dp_phy>; - phy-names = "dp"; - }; - -Board Specific portion: - dp-controller { - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <4>; - - display-timings { - native-mode = <&lcd_timing>; - lcd_timing: 1366x768 { - clock-frequency = <70589280>; - hactive = <1366>; - vactive = <768>; - hfront-porch = <40>; - hback-porch = <40>; - hsync-len = <32>; - vback-porch = <10>; - vfront-porch = <12>; - vsync-len = <6>; - }; - }; - - ports { - port@0 { - dp_out: endpoint { - remote-endpoint = <&bridge_in>; - }; - }; - }; - }; |