diff options
Diffstat (limited to 'Documentation/hwmon/it87')
| -rw-r--r-- | Documentation/hwmon/it87 | 35 |
1 files changed, 22 insertions, 13 deletions
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87 index e87294878..733296d65 100644 --- a/Documentation/hwmon/it87 +++ b/Documentation/hwmon/it87 @@ -38,6 +38,10 @@ Supported chips: Prefix: 'it8728' Addresses scanned: from Super I/O config space (8 I/O ports) Datasheet: Not publicly available + * IT8732F + Prefix: 'it8732' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * IT8771E Prefix: 'it8771' Addresses scanned: from Super I/O config space (8 I/O ports) @@ -111,9 +115,9 @@ Description ----------- This driver implements support for the IT8603E, IT8620E, IT8623E, IT8705F, -IT8712F, IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, -IT8771E, IT8772E, IT8781F, IT8782F, IT8783E/F, IT8786E, IT8790E, and SiS950 -chips. +IT8712F, IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8732F, +IT8758E, IT8771E, IT8772E, IT8781F, IT8782F, IT8783E/F, IT8786E, IT8790E, and +SiS950 chips. These chips are 'Super I/O chips', supporting floppy disks, infrared ports, joysticks and other miscellaneous stuff. For hardware monitoring, they @@ -137,10 +141,10 @@ The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E and later IT8712F revisions have support for 2 additional fans. The additional fans are supported by the driver. -The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8781F, IT8782F, IT8783E/F, -and late IT8712F and IT8705F also have optional 16-bit tachometer counters -for fans 1 to 3. This is better (no more fan clock divider mess) but not -compatible with the older chips and revisions. The 16-bit tachometer mode +The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8732F, IT8781F, IT8782F, +IT8783E/F, and late IT8712F and IT8705F also have optional 16-bit tachometer +counters for fans 1 to 3. This is better (no more fan clock divider mess) but +not compatible with the older chips and revisions. The 16-bit tachometer mode is enabled by the driver when one of the above chips is detected. The IT8726F is just bit enhanced IT8716F with additional hardware @@ -159,6 +163,9 @@ IT8728F. It only supports 16-bit fan mode. The IT8790E supports up to 3 fans. 16-bit fan mode is always enabled. +The IT8732F supports a closed-loop mode for fan control, but this is not +currently implemented by the driver. + Temperatures are measured in degrees Celsius. An alarm is triggered once when the Overtemperature Shutdown limit is crossed. @@ -173,12 +180,14 @@ is done. Voltage sensors (also known as IN sensors) report their values in volts. An alarm is triggered if the voltage has crossed a programmable minimum or maximum limit. Note that minimum in this case always means 'closest to -zero'; this is important for negative voltage measurements. All voltage -inputs can measure voltages between 0 and 4.08 volts, with a resolution of -0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The -battery voltage in8 does not have limit registers. - -On the IT8603E, IT8721F/IT8758E, IT8781F, IT8782F, and IT8783E/F, some +zero'; this is important for negative voltage measurements. On most chips, all +voltage inputs can measure voltages between 0 and 4.08 volts, with a resolution +of 0.016 volt. IT8603E, IT8721F/IT8758E and IT8728F can measure between 0 and +3.06 volts, with a resolution of 0.012 volt. IT8732F can measure between 0 and +2.8 volts with a resolution of 0.0109 volt. The battery voltage in8 does not +have limit registers. + +On the IT8603E, IT8721F/IT8758E, IT8732F, IT8781F, IT8782F, and IT8783E/F, some voltage inputs are internal and scaled inside the chip: * in3 (optional) * in7 (optional for IT8781F, IT8782F, and IT8783E/F) |