diff options
Diffstat (limited to 'Documentation/remoteproc.txt')
| -rw-r--r-- | Documentation/remoteproc.txt | 299 |
1 files changed, 299 insertions, 0 deletions
diff --git a/Documentation/remoteproc.txt b/Documentation/remoteproc.txt new file mode 100644 index 000000000..e6469fdcf --- /dev/null +++ b/Documentation/remoteproc.txt @@ -0,0 +1,299 @@ +Remote Processor Framework + +1. Introduction + +Modern SoCs typically have heterogeneous remote processor devices in asymmetric +multiprocessing (AMP) configurations, which may be running different instances +of operating system, whether it's Linux or any other flavor of real-time OS. + +OMAP4, for example, has dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP. +In a typical configuration, the dual cortex-A9 is running Linux in a SMP +configuration, and each of the other three cores (two M3 cores and a DSP) +is running its own instance of RTOS in an AMP configuration. + +The remoteproc framework allows different platforms/architectures to +control (power on, load firmware, power off) those remote processors while +abstracting the hardware differences, so the entire driver doesn't need to be +duplicated. In addition, this framework also adds rpmsg virtio devices +for remote processors that supports this kind of communication. This way, +platform-specific remoteproc drivers only need to provide a few low-level +handlers, and then all rpmsg drivers will then just work +(for more information about the virtio-based rpmsg bus and its drivers, +please read Documentation/rpmsg.txt). +Registration of other types of virtio devices is now also possible. Firmwares +just need to publish what kind of virtio devices do they support, and then +remoteproc will add those devices. This makes it possible to reuse the +existing virtio drivers with remote processor backends at a minimal development +cost. + +2. User API + + int rproc_boot(struct rproc *rproc) + - Boot a remote processor (i.e. load its firmware, power it on, ...). + If the remote processor is already powered on, this function immediately + returns (successfully). + Returns 0 on success, and an appropriate error value otherwise. + Note: to use this function you should already have a valid rproc + handle. There are several ways to achieve that cleanly (devres, pdata, + the way remoteproc_rpmsg.c does this, or, if this becomes prevalent, we + might also consider using dev_archdata for this). + + void rproc_shutdown(struct rproc *rproc) + - Power off a remote processor (previously booted with rproc_boot()). + In case @rproc is still being used by an additional user(s), then + this function will just decrement the power refcount and exit, + without really powering off the device. + Every call to rproc_boot() must (eventually) be accompanied by a call + to rproc_shutdown(). Calling rproc_shutdown() redundantly is a bug. + Notes: + - we're not decrementing the rproc's refcount, only the power refcount. + which means that the @rproc handle stays valid even after + rproc_shutdown() returns, and users can still use it with a subsequent + rproc_boot(), if needed. + +3. Typical usage + +#include <linux/remoteproc.h> + +/* in case we were given a valid 'rproc' handle */ +int dummy_rproc_example(struct rproc *my_rproc) +{ + int ret; + + /* let's power on and boot our remote processor */ + ret = rproc_boot(my_rproc); + if (ret) { + /* + * something went wrong. handle it and leave. + */ + } + + /* + * our remote processor is now powered on... give it some work + */ + + /* let's shut it down now */ + rproc_shutdown(my_rproc); +} + +4. API for implementors + + struct rproc *rproc_alloc(struct device *dev, const char *name, + const struct rproc_ops *ops, + const char *firmware, int len) + - Allocate a new remote processor handle, but don't register + it yet. Required parameters are the underlying device, the + name of this remote processor, platform-specific ops handlers, + the name of the firmware to boot this rproc with, and the + length of private data needed by the allocating rproc driver (in bytes). + + This function should be used by rproc implementations during + initialization of the remote processor. + After creating an rproc handle using this function, and when ready, + implementations should then call rproc_add() to complete + the registration of the remote processor. + On success, the new rproc is returned, and on failure, NULL. + + Note: _never_ directly deallocate @rproc, even if it was not registered + yet. Instead, when you need to unroll rproc_alloc(), use rproc_put(). + + void rproc_put(struct rproc *rproc) + - Free an rproc handle that was allocated by rproc_alloc. + This function essentially unrolls rproc_alloc(), by decrementing the + rproc's refcount. It doesn't directly free rproc; that would happen + only if there are no other references to rproc and its refcount now + dropped to zero. + + int rproc_add(struct rproc *rproc) + - Register @rproc with the remoteproc framework, after it has been + allocated with rproc_alloc(). + This is called by the platform-specific rproc implementation, whenever + a new remote processor device is probed. + Returns 0 on success and an appropriate error code otherwise. + Note: this function initiates an asynchronous firmware loading + context, which will look for virtio devices supported by the rproc's + firmware. + If found, those virtio devices will be created and added, so as a result + of registering this remote processor, additional virtio drivers might get + probed. + + int rproc_del(struct rproc *rproc) + - Unroll rproc_add(). + This function should be called when the platform specific rproc + implementation decides to remove the rproc device. it should + _only_ be called if a previous invocation of rproc_add() + has completed successfully. + + After rproc_del() returns, @rproc is still valid, and its + last refcount should be decremented by calling rproc_put(). + + Returns 0 on success and -EINVAL if @rproc isn't valid. + + void rproc_report_crash(struct rproc *rproc, enum rproc_crash_type type) + - Report a crash in a remoteproc + This function must be called every time a crash is detected by the + platform specific rproc implementation. This should not be called from a + non-remoteproc driver. This function can be called from atomic/interrupt + context. + +5. Implementation callbacks + +These callbacks should be provided by platform-specific remoteproc +drivers: + +/** + * struct rproc_ops - platform-specific device handlers + * @start: power on the device and boot it + * @stop: power off the device + * @kick: kick a virtqueue (virtqueue id given as a parameter) + */ +struct rproc_ops { + int (*start)(struct rproc *rproc); + int (*stop)(struct rproc *rproc); + void (*kick)(struct rproc *rproc, int vqid); +}; + +Every remoteproc implementation should at least provide the ->start and ->stop +handlers. If rpmsg/virtio functionality is also desired, then the ->kick handler +should be provided as well. + +The ->start() handler takes an rproc handle and should then power on the +device and boot it (use rproc->priv to access platform-specific private data). +The boot address, in case needed, can be found in rproc->bootaddr (remoteproc +core puts there the ELF entry point). +On success, 0 should be returned, and on failure, an appropriate error code. + +The ->stop() handler takes an rproc handle and powers the device down. +On success, 0 is returned, and on failure, an appropriate error code. + +The ->kick() handler takes an rproc handle, and an index of a virtqueue +where new message was placed in. Implementations should interrupt the remote +processor and let it know it has pending messages. Notifying remote processors +the exact virtqueue index to look in is optional: it is easy (and not +too expensive) to go through the existing virtqueues and look for new buffers +in the used rings. + +6. Binary Firmware Structure + +At this point remoteproc only supports ELF32 firmware binaries. However, +it is quite expected that other platforms/devices which we'd want to +support with this framework will be based on different binary formats. + +When those use cases show up, we will have to decouple the binary format +from the framework core, so we can support several binary formats without +duplicating common code. + +When the firmware is parsed, its various segments are loaded to memory +according to the specified device address (might be a physical address +if the remote processor is accessing memory directly). + +In addition to the standard ELF segments, most remote processors would +also include a special section which we call "the resource table". + +The resource table contains system resources that the remote processor +requires before it should be powered on, such as allocation of physically +contiguous memory, or iommu mapping of certain on-chip peripherals. +Remotecore will only power up the device after all the resource table's +requirement are met. + +In addition to system resources, the resource table may also contain +resource entries that publish the existence of supported features +or configurations by the remote processor, such as trace buffers and +supported virtio devices (and their configurations). + +The resource table begins with this header: + +/** + * struct resource_table - firmware resource table header + * @ver: version number + * @num: number of resource entries + * @reserved: reserved (must be zero) + * @offset: array of offsets pointing at the various resource entries + * + * The header of the resource table, as expressed by this structure, + * contains a version number (should we need to change this format in the + * future), the number of available resource entries, and their offsets + * in the table. + */ +struct resource_table { + u32 ver; + u32 num; + u32 reserved[2]; + u32 offset[0]; +} __packed; + +Immediately following this header are the resource entries themselves, +each of which begins with the following resource entry header: + +/** + * struct fw_rsc_hdr - firmware resource entry header + * @type: resource type + * @data: resource data + * + * Every resource entry begins with a 'struct fw_rsc_hdr' header providing + * its @type. The content of the entry itself will immediately follow + * this header, and it should be parsed according to the resource type. + */ +struct fw_rsc_hdr { + u32 type; + u8 data[0]; +} __packed; + +Some resources entries are mere announcements, where the host is informed +of specific remoteproc configuration. Other entries require the host to +do something (e.g. allocate a system resource). Sometimes a negotiation +is expected, where the firmware requests a resource, and once allocated, +the host should provide back its details (e.g. address of an allocated +memory region). + +Here are the various resource types that are currently supported: + +/** + * enum fw_resource_type - types of resource entries + * + * @RSC_CARVEOUT: request for allocation of a physically contiguous + * memory region. + * @RSC_DEVMEM: request to iommu_map a memory-based peripheral. + * @RSC_TRACE: announces the availability of a trace buffer into which + * the remote processor will be writing logs. + * @RSC_VDEV: declare support for a virtio device, and serve as its + * virtio header. + * @RSC_LAST: just keep this one at the end + * + * Please note that these values are used as indices to the rproc_handle_rsc + * lookup table, so please keep them sane. Moreover, @RSC_LAST is used to + * check the validity of an index before the lookup table is accessed, so + * please update it as needed. + */ +enum fw_resource_type { + RSC_CARVEOUT = 0, + RSC_DEVMEM = 1, + RSC_TRACE = 2, + RSC_VDEV = 3, + RSC_LAST = 4, +}; + +For more details regarding a specific resource type, please see its +dedicated structure in include/linux/remoteproc.h. + +We also expect that platform-specific resource entries will show up +at some point. When that happens, we could easily add a new RSC_PLATFORM +type, and hand those resources to the platform-specific rproc driver to handle. + +7. Virtio and remoteproc + +The firmware should provide remoteproc information about virtio devices +that it supports, and their configurations: a RSC_VDEV resource entry +should specify the virtio device id (as in virtio_ids.h), virtio features, +virtio config space, vrings information, etc. + +When a new remote processor is registered, the remoteproc framework +will look for its resource table and will register the virtio devices +it supports. A firmware may support any number of virtio devices, and +of any type (a single remote processor can also easily support several +rpmsg virtio devices this way, if desired). + +Of course, RSC_VDEV resource entries are only good enough for static +allocation of virtio devices. Dynamic allocations will also be made possible +using the rpmsg bus (similar to how we already do dynamic allocations of +rpmsg channels; read more about it in rpmsg.txt). |