summaryrefslogtreecommitdiff
path: root/Documentation/video4linux/README.cpia2
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/video4linux/README.cpia2')
-rw-r--r--Documentation/video4linux/README.cpia2130
1 files changed, 130 insertions, 0 deletions
diff --git a/Documentation/video4linux/README.cpia2 b/Documentation/video4linux/README.cpia2
new file mode 100644
index 000000000..38e742fd0
--- /dev/null
+++ b/Documentation/video4linux/README.cpia2
@@ -0,0 +1,130 @@
+$Id: README,v 1.7 2005/08/29 23:39:57 sbertin Exp $
+
+1. Introduction
+
+ This is a driver for STMicroelectronics's CPiA2 (second generation
+Colour Processor Interface ASIC) based cameras. This camera outputs an MJPEG
+stream at up to vga size. It implements the Video4Linux interface as much as
+possible. Since the V4L interface does not support compressed formats, only
+an mjpeg enabled application can be used with the camera. We have modified the
+gqcam application to view this stream.
+
+ The driver is implemented as two kernel modules. The cpia2 module
+contains the camera functions and the V4L interface. The cpia2_usb module
+contains usb specific functions. The main reason for this was the size of the
+module was getting out of hand, so I separated them. It is not likely that
+there will be a parallel port version.
+
+FEATURES:
+ - Supports cameras with the Vision stv6410 (CIF) and stv6500 (VGA) cmos
+ sensors. I only have the vga sensor, so can't test the other.
+ - Image formats: VGA, QVGA, CIF, QCIF, and a number of sizes in between.
+ VGA and QVGA are the native image sizes for the VGA camera. CIF is done
+ in the coprocessor by scaling QVGA. All other sizes are done by clipping.
+ - Palette: YCrCb, compressed with MJPEG.
+ - Some compression parameters are settable.
+ - Sensor framerate is adjustable (up to 30 fps CIF, 15 fps VGA).
+ - Adjust brightness, color, contrast while streaming.
+ - Flicker control settable for 50 or 60 Hz mains frequency.
+
+2. Making and installing the stv672 driver modules:
+
+ Requirements:
+ -------------
+ This should work with 2.4 (2.4.23 and later) and 2.6 kernels, but has
+only been tested on 2.6. Video4Linux must be either compiled into the kernel or
+available as a module. Video4Linux2 is automatically detected and made
+available at compile time.
+
+ Compiling:
+ ----------
+ As root, do a make install. This will compile and install the modules
+into the media/video directory in the module tree. For 2.4 kernels, use
+Makefile_2.4 (aka do make -f Makefile_2.4 install).
+
+ Setup:
+ ------
+ Use 'modprobe cpia2' to load and 'modprobe -r cpia2' to unload. This
+may be done automatically by your distribution.
+
+3. Driver options
+
+ Option Description
+ ------ -----------
+ video_nr video device to register (0=/dev/video0, etc)
+ range -1 to 64. default is -1 (first available)
+ If you have more than 1 camera, this MUST be -1.
+ buffer_size Size for each frame buffer in bytes (default 68k)
+ num_buffers Number of frame buffers (1-32, default 3)
+ alternate USB Alternate (2-7, default 7)
+ flicker_freq Frequency for flicker reduction(50 or 60, default 60)
+ flicker_mode 0 to disable, or 1 to enable flicker reduction.
+ (default 0). This is only effective if the camera
+ uses a stv0672 coprocessor.
+
+ Setting the options:
+ --------------------
+ If you are using modules, edit /etc/modules.conf and add an options
+line like this:
+ options cpia2 num_buffers=3 buffer_size=65535
+
+ If the driver is compiled into the kernel, at boot time specify them
+like this:
+ cpia2.num_buffers=3 cpia2.buffer_size=65535
+
+ What buffer size should I use?
+ ------------------------------
+ The maximum image size depends on the alternate you choose, and the
+frame rate achieved by the camera. If the compression engine is able to
+keep up with the frame rate, the maximum image size is given by the table
+below.
+ The compression engine starts out at maximum compression, and will
+increase image quality until it is close to the size in the table. As long
+as the compression engine can keep up with the frame rate, after a short time
+the images will all be about the size in the table, regardless of resolution.
+ At low alternate settings, the compression engine may not be able to
+compress the image enough and will reduce the frame rate by producing larger
+images.
+ The default of 68k should be good for most users. This will handle
+any alternate at frame rates down to 15fps. For lower frame rates, it may
+be necessary to increase the buffer size to avoid having frames dropped due
+to insufficient space.
+
+ Image size(bytes)
+ Alternate bytes/ms 15fps 30fps
+ 2 128 8533 4267
+ 3 384 25600 12800
+ 4 640 42667 21333
+ 5 768 51200 25600
+ 6 896 59733 29867
+ 7 1023 68200 34100
+
+ How many buffers should I use?
+ ------------------------------
+ For normal streaming, 3 should give the best results. With only 2,
+it is possible for the camera to finish sending one image just after a
+program has started reading the other. If this happens, the driver must drop
+a frame. The exception to this is if you have a heavily loaded machine. In
+this case use 2 buffers. You are probably not reading at the full frame rate.
+If the camera can send multiple images before a read finishes, it could
+overwrite the third buffer before the read finishes, leading to a corrupt
+image. Single and double buffering have extra checks to avoid overwriting.
+
+4. Using the camera
+
+ We are providing a modified gqcam application to view the output. In
+order to avoid confusion, here it is called mview. There is also the qx5view
+program which can also control the lights on the qx5 microscope. MJPEG Tools
+(http://mjpeg.sourceforge.net) can also be used to record from the camera.
+
+5. Notes to developers:
+
+ - This is a driver version stripped of the 2.4 back compatibility
+ and old MJPEG ioctl API. See cpia2.sf.net for 2.4 support.
+
+6. Thanks:
+
+ - Peter Pregler <Peter_Pregler@email.com>,
+ Scott J. Bertin <scottbertin@yahoo.com>, and
+ Jarl Totland <Jarl.Totland@bdc.no> for the original cpia driver, which
+ this one was modelled from.