diff options
Diffstat (limited to 'Documentation/virtual/kvm/ppc-pv.txt')
| -rw-r--r-- | Documentation/virtual/kvm/ppc-pv.txt | 212 |
1 files changed, 212 insertions, 0 deletions
diff --git a/Documentation/virtual/kvm/ppc-pv.txt b/Documentation/virtual/kvm/ppc-pv.txt new file mode 100644 index 000000000..319560646 --- /dev/null +++ b/Documentation/virtual/kvm/ppc-pv.txt @@ -0,0 +1,212 @@ +The PPC KVM paravirtual interface +================================= + +The basic execution principle by which KVM on PowerPC works is to run all kernel +space code in PR=1 which is user space. This way we trap all privileged +instructions and can emulate them accordingly. + +Unfortunately that is also the downfall. There are quite some privileged +instructions that needlessly return us to the hypervisor even though they +could be handled differently. + +This is what the PPC PV interface helps with. It takes privileged instructions +and transforms them into unprivileged ones with some help from the hypervisor. +This cuts down virtualization costs by about 50% on some of my benchmarks. + +The code for that interface can be found in arch/powerpc/kernel/kvm* + +Querying for existence +====================== + +To find out if we're running on KVM or not, we leverage the device tree. When +Linux is running on KVM, a node /hypervisor exists. That node contains a +compatible property with the value "linux,kvm". + +Once you determined you're running under a PV capable KVM, you can now use +hypercalls as described below. + +KVM hypercalls +============== + +Inside the device tree's /hypervisor node there's a property called +'hypercall-instructions'. This property contains at most 4 opcodes that make +up the hypercall. To call a hypercall, just call these instructions. + +The parameters are as follows: + + Register IN OUT + + r0 - volatile + r3 1st parameter Return code + r4 2nd parameter 1st output value + r5 3rd parameter 2nd output value + r6 4th parameter 3rd output value + r7 5th parameter 4th output value + r8 6th parameter 5th output value + r9 7th parameter 6th output value + r10 8th parameter 7th output value + r11 hypercall number 8th output value + r12 - volatile + +Hypercall definitions are shared in generic code, so the same hypercall numbers +apply for x86 and powerpc alike with the exception that each KVM hypercall +also needs to be ORed with the KVM vendor code which is (42 << 16). + +Return codes can be as follows: + + Code Meaning + + 0 Success + 12 Hypercall not implemented + <0 Error + +The magic page +============== + +To enable communication between the hypervisor and guest there is a new shared +page that contains parts of supervisor visible register state. The guest can +map this shared page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE. + +With this hypercall issued the guest always gets the magic page mapped at the +desired location. The first parameter indicates the effective address when the +MMU is enabled. The second parameter indicates the address in real mode, if +applicable to the target. For now, we always map the page to -4096. This way we +can access it using absolute load and store functions. The following +instruction reads the first field of the magic page: + + ld rX, -4096(0) + +The interface is designed to be extensible should there be need later to add +additional registers to the magic page. If you add fields to the magic page, +also define a new hypercall feature to indicate that the host can give you more +registers. Only if the host supports the additional features, make use of them. + +The magic page layout is described by struct kvm_vcpu_arch_shared +in arch/powerpc/include/asm/kvm_para.h. + +Magic page features +=================== + +When mapping the magic page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE, +a second return value is passed to the guest. This second return value contains +a bitmap of available features inside the magic page. + +The following enhancements to the magic page are currently available: + + KVM_MAGIC_FEAT_SR Maps SR registers r/w in the magic page + KVM_MAGIC_FEAT_MAS0_TO_SPRG7 Maps MASn, ESR, PIR and high SPRGs + +For enhanced features in the magic page, please check for the existence of the +feature before using them! + +Magic page flags +================ + +In addition to features that indicate whether a host is capable of a particular +feature we also have a channel for a guest to tell the guest whether it's capable +of something. This is what we call "flags". + +Flags are passed to the host in the low 12 bits of the Effective Address. + +The following flags are currently available for a guest to expose: + + MAGIC_PAGE_FLAG_NOT_MAPPED_NX Guest handles NX bits correclty wrt magic page + +MSR bits +======== + +The MSR contains bits that require hypervisor intervention and bits that do +not require direct hypervisor intervention because they only get interpreted +when entering the guest or don't have any impact on the hypervisor's behavior. + +The following bits are safe to be set inside the guest: + + MSR_EE + MSR_RI + +If any other bit changes in the MSR, please still use mtmsr(d). + +Patched instructions +==================== + +The "ld" and "std" instructions are transformed to "lwz" and "stw" instructions +respectively on 32 bit systems with an added offset of 4 to accommodate for big +endianness. + +The following is a list of mapping the Linux kernel performs when running as +guest. Implementing any of those mappings is optional, as the instruction traps +also act on the shared page. So calling privileged instructions still works as +before. + +From To +==== == + +mfmsr rX ld rX, magic_page->msr +mfsprg rX, 0 ld rX, magic_page->sprg0 +mfsprg rX, 1 ld rX, magic_page->sprg1 +mfsprg rX, 2 ld rX, magic_page->sprg2 +mfsprg rX, 3 ld rX, magic_page->sprg3 +mfsrr0 rX ld rX, magic_page->srr0 +mfsrr1 rX ld rX, magic_page->srr1 +mfdar rX ld rX, magic_page->dar +mfdsisr rX lwz rX, magic_page->dsisr + +mtmsr rX std rX, magic_page->msr +mtsprg 0, rX std rX, magic_page->sprg0 +mtsprg 1, rX std rX, magic_page->sprg1 +mtsprg 2, rX std rX, magic_page->sprg2 +mtsprg 3, rX std rX, magic_page->sprg3 +mtsrr0 rX std rX, magic_page->srr0 +mtsrr1 rX std rX, magic_page->srr1 +mtdar rX std rX, magic_page->dar +mtdsisr rX stw rX, magic_page->dsisr + +tlbsync nop + +mtmsrd rX, 0 b <special mtmsr section> +mtmsr rX b <special mtmsr section> + +mtmsrd rX, 1 b <special mtmsrd section> + +[Book3S only] +mtsrin rX, rY b <special mtsrin section> + +[BookE only] +wrteei [0|1] b <special wrteei section> + + +Some instructions require more logic to determine what's going on than a load +or store instruction can deliver. To enable patching of those, we keep some +RAM around where we can live translate instructions to. What happens is the +following: + + 1) copy emulation code to memory + 2) patch that code to fit the emulated instruction + 3) patch that code to return to the original pc + 4 + 4) patch the original instruction to branch to the new code + +That way we can inject an arbitrary amount of code as replacement for a single +instruction. This allows us to check for pending interrupts when setting EE=1 +for example. + +Hypercall ABIs in KVM on PowerPC +================================= +1) KVM hypercalls (ePAPR) + +These are ePAPR compliant hypercall implementation (mentioned above). Even +generic hypercalls are implemented here, like the ePAPR idle hcall. These are +available on all targets. + +2) PAPR hypercalls + +PAPR hypercalls are needed to run server PowerPC PAPR guests (-M pseries in QEMU). +These are the same hypercalls that pHyp, the POWER hypervisor implements. Some of +them are handled in the kernel, some are handled in user space. This is only +available on book3s_64. + +3) OSI hypercalls + +Mac-on-Linux is another user of KVM on PowerPC, which has its own hypercall (long +before KVM). This is supported to maintain compatibility. All these hypercalls get +forwarded to user space. This is only useful on book3s_32, but can be used with +book3s_64 as well. |