diff options
Diffstat (limited to 'arch/arm/boot/dts/armada-370-synology-ds213j.dts')
| -rw-r--r-- | arch/arm/boot/dts/armada-370-synology-ds213j.dts | 348 |
1 files changed, 348 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/armada-370-synology-ds213j.dts new file mode 100644 index 000000000..b42b76776 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-synology-ds213j.dts @@ -0,0 +1,348 @@ +/* + * Device Tree file for Synology DS213j + * + * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the old 0xd0000000). + * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot + * bootloaders provided by Marvell. It is used in recent versions of + * DSM software provided by Synology. Nonetheless, some earlier boards + * were delivered with an older version of u-boot that left internal + * registers mapped at 0xd0000000. If you have such a device you will + * not be able to directly boot a kernel based on this Device Tree. In + * that case, the preferred solution is to update your bootloader (e.g. + * by upgrading to latest version of DSM, or building a new one and + * installing it from u-boot prompt) or adjust the Devive Tree + * (s/0xf1000000/0xd0000000/ in 'ranges' below). + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "armada-370.dtsi" + +/ { + model = "Synology DS213j"; + compatible = "synology,ds213j", "marvell,armada370", + "marvell,armada-370-xp"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; /* 512 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + + internal-regs { + + /* RTC provided by Seiko S-35390A I2C RTC chip below */ + rtc@10300 { + status = "disabled"; + }; + + spi0: spi@10600 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q064"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <20000000>; + + /* + * Warning! + * + * Synology u-boot uses its compiled-in environment + * and it seems Synology did not care to change u-boot + * default configuration in order to allow saving a + * modified environment at a sensible location. So, + * if you do a 'saveenv' under u-boot, your modified + * environment will be saved at 1MB after the start + * of the flash, i.e. in the middle of the uImage. + * For that reason, it is strongly advised not to + * change the default environment, unless you know + * what you are doing. + */ + partition@00000000 { /* u-boot */ + label = "RedBoot"; + reg = <0x00000000 0x000c0000>; /* 768KB */ + }; + + partition@000c0000 { /* uImage */ + label = "zImage"; + reg = <0x000c0000 0x002d0000>; /* 2880KB */ + }; + + partition@00390000 { /* uInitramfs */ + label = "rd.gz"; + reg = <0x00390000 0x00440000>; /* 4250KB */ + }; + + partition@007d0000 { /* MAC address and serial number */ + label = "vendor"; + reg = <0x007d0000 0x00010000>; /* 64KB */ + }; + + partition@007e0000 { + label = "RedBoot config"; + reg = <0x007e0000 0x00010000>; /* 64KB */ + }; + + partition@007f0000 { + label = "FIS directory"; + reg = <0x007f0000 0x00010000>; /* 64KB */ + }; + }; + }; + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + clock-frequency = <400000>; + status = "okay"; + + /* Main device RTC chip */ + s35390a: s35390a@30 { + compatible = "sii,s35390a"; + reg = <0x30>; + }; + }; + + /* Connected to a header on device's PCB */ + serial@12000 { + status = "okay"; + }; + + /* Connected to a TI MSP430F2111 for power control */ + serial@12100 { + status = "okay"; + }; + + poweroff@12100 { + compatible = "synology,power-off"; + reg = <0x12100 0x100>; + clocks = <&coreclk 0>; + }; + + /* rear USB port, near reset button */ + usb@50000 { + status = "okay"; + }; + + /* rear USB port, near RJ45 port */ + usb@51000 { + status = "okay"; + }; + + mdio { + phy1: ethernet-phy@1 { /* Marvell 88E1512 */ + reg = <1>; + }; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "sgmii"; + }; + + sata@a0000 { + nr-ports = <2>; + status = "okay"; + }; + }; + }; + + gpio-fan-32-38 { + status = "okay"; + compatible = "gpio-fan"; + pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin + &fan_ctrl_high_pin &fan_alarm_pin>; + pinctrl-names = "default"; + gpios = <&gpio1 31 GPIO_ACTIVE_HIGH + &gpio2 0 GPIO_ACTIVE_HIGH + &gpio2 1 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 1000 1 + 1150 2 + 1350 4 + 1500 3 + 1650 5 + 1750 6 + 1900 7 >; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&disk1_led_pin + &disk2_led_pin>; + pinctrl-names = "default"; + + disk1-led-amber { + label = "synology:amber:disk1"; + gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + disk2-led-amber { + label = "synology:amber:disk2"; + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>; + pinctrl-names = "default"; + + sata1_regulator: sata1-regulator { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "SATA1 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <2000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; + + sata2_regulator: sata2-regulator { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA2 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <4000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&pinctrl { + disk1_led_pin: disk1-led-pin { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; + + disk2_led_pin: disk2-led-pin { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + + sata1_pwr_pin: sata1-pwr-pin { + marvell,pins = "mpp37"; + marvell,function = "gpio"; + }; + + sata2_pwr_pin: sata2-pwr-pin { + marvell,pins = "mpp62"; + marvell,function = "gpio"; + }; + + sata1_pres_pin: sata1-pres-pin { + marvell,pins = "mpp60"; + marvell,function = "gpio"; + }; + + sata2_pres_pin: sata2-pres-pin { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + + syno_id_bit0_pin: syno-id-bit0-pin { + marvell,pins = "mpp55"; + marvell,function = "gpio"; + }; + + syno_id_bit1_pin: syno-id-bit1-pin { + marvell,pins = "mpp56"; + marvell,function = "gpio"; + }; + + syno_id_bit2_pin: syno-id-bit2-pin { + marvell,pins = "mpp57"; + marvell,function = "gpio"; + }; + + syno_id_bit3_pin: syno-id-bit3-pin { + marvell,pins = "mpp58"; + marvell,function = "gpio"; + }; + + fan_ctrl_low_pin: fan-ctrl-low-pin { + marvell,pins = "mpp65"; + marvell,function = "gpio"; + }; + + fan_ctrl_mid_pin: fan-ctrl-mid-pin { + marvell,pins = "mpp64"; + marvell,function = "gpio"; + }; + + fan_ctrl_high_pin: fan-ctrl-high-pin { + marvell,pins = "mpp63"; + marvell,function = "gpo"; + }; + + fan_alarm_pin: fan-alarm-pin { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; +}; |