diff options
Diffstat (limited to 'arch/arm/boot/dts/phy3250.dts')
| -rw-r--r-- | arch/arm/boot/dts/phy3250.dts | 227 |
1 files changed, 0 insertions, 227 deletions
diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts deleted file mode 100644 index a00d7ce78..000000000 --- a/arch/arm/boot/dts/phy3250.dts +++ /dev/null @@ -1,227 +0,0 @@ -/* - * PHYTEC phyCORE-LPC3250 board - * - * Copyright 2012 Roland Stigge <stigge@antcom.de> - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "lpc32xx.dtsi" - -/ { - model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; - compatible = "phytec,phy3250", "nxp,lpc3250"; - #address-cells = <1>; - #size-cells = <1>; - - memory { - device_type = "memory"; - reg = <0x80000000 0x4000000>; - }; - - regulators { - backlight_reg: regulator@0 { - compatible = "regulator-fixed"; - regulator-name = "backlight_reg"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio 5 4 0>; - enable-active-high; - regulator-boot-on; - }; - - lcd_reg: regulator@1 { - compatible = "regulator-fixed"; - regulator-name = "lcd_reg"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio 5 0 0>; - enable-active-high; - regulator-boot-on; - }; - - sd_reg: regulator@2 { - compatible = "regulator-fixed"; - regulator-name = "sd_reg"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio 5 5 0>; - enable-active-high; - }; - }; - - ahb { - mac: ethernet@31060000 { - phy-mode = "rmii"; - use-iram; - }; - - clcd@31040000 { - status = "okay"; - }; - - /* 64MB Flash via SLC NAND controller */ - slc: flash@20020000 { - status = "okay"; - #address-cells = <1>; - #size-cells = <1>; - - nxp,wdr-clks = <14>; - nxp,wwidth = <40000000>; - nxp,whold = <100000000>; - nxp,wsetup = <100000000>; - nxp,rdr-clks = <14>; - nxp,rwidth = <40000000>; - nxp,rhold = <66666666>; - nxp,rsetup = <100000000>; - nand-on-flash-bbt; - gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ - - mtd0@00000000 { - label = "phy3250-boot"; - reg = <0x00000000 0x00064000>; - read-only; - }; - - mtd1@00064000 { - label = "phy3250-uboot"; - reg = <0x00064000 0x00190000>; - read-only; - }; - - mtd2@001f4000 { - label = "phy3250-ubt-prms"; - reg = <0x001f4000 0x00010000>; - }; - - mtd3@00204000 { - label = "phy3250-kernel"; - reg = <0x00204000 0x00400000>; - }; - - mtd4@00604000 { - label = "phy3250-rootfs"; - reg = <0x00604000 0x039fc000>; - }; - }; - - apb { - uart5: serial@40090000 { - status = "okay"; - }; - - uart3: serial@40080000 { - status = "okay"; - }; - - i2c1: i2c@400A0000 { - clock-frequency = <100000>; - - pcf8563: rtc@51 { - compatible = "nxp,pcf8563"; - reg = <0x51>; - }; - - uda1380: uda1380@18 { - compatible = "nxp,uda1380"; - reg = <0x18>; - power-gpio = <&gpio 0x59 0>; - reset-gpio = <&gpio 0x51 0>; - dac-clk = "wspll"; - }; - }; - - i2c2: i2c@400A8000 { - clock-frequency = <100000>; - }; - - ssp0: ssp@20084000 { - #address-cells = <1>; - #size-cells = <0>; - num-cs = <1>; - cs-gpios = <&gpio 3 5 0>; - - eeprom: at25@0 { - pl022,interface = <0>; - pl022,com-mode = <0>; - pl022,rx-level-trig = <1>; - pl022,tx-level-trig = <1>; - pl022,ctrl-len = <11>; - pl022,wait-state = <0>; - pl022,duplex = <0>; - - at25,byte-len = <0x8000>; - at25,addr-mode = <2>; - at25,page-size = <64>; - - compatible = "atmel,at25"; - reg = <0>; - spi-max-frequency = <5000000>; - }; - }; - - sd@20098000 { - wp-gpios = <&gpio 3 0 0>; - cd-gpios = <&gpio 3 1 0>; - cd-inverted; - bus-width = <4>; - vmmc-supply = <&sd_reg>; - status = "okay"; - }; - }; - - fab { - uart2: serial@40018000 { - status = "okay"; - }; - - tsc@40048000 { - status = "okay"; - }; - - key@40050000 { - status = "okay"; - keypad,num-rows = <1>; - keypad,num-columns = <1>; - nxp,debounce-delay-ms = <3>; - nxp,scan-delay-ms = <34>; - linux,keymap = <0x00000002>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - led0 { /* red */ - gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */ - default-state = "off"; - }; - - led1 { /* green */ - gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */ - linux,default-trigger = "heartbeat"; - }; - }; -}; - -/* Here, choose exactly one from: ohci, usbd */ -&ohci /* &usbd */ { - transceiver = <&isp1301>; - status = "okay"; -}; - -&i2cusb { - clock-frequency = <100000>; - - isp1301: usb-transceiver@2c { - compatible = "nxp,isp1301"; - reg = <0x2c>; - }; -}; |