diff options
Diffstat (limited to 'arch/cris/arch-v32/drivers/Kconfig')
| -rw-r--r-- | arch/cris/arch-v32/drivers/Kconfig | 167 |
1 files changed, 0 insertions, 167 deletions
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig index e6c523cc4..2735eb767 100644 --- a/arch/cris/arch-v32/drivers/Kconfig +++ b/arch/cris/arch-v32/drivers/Kconfig @@ -149,173 +149,6 @@ config ETRAX_NANDBOOT Say Y if your boot code, kernel and root file system is in NAND flash. Say N if they are in NOR flash. -config ETRAX_I2C - bool "I2C driver" - depends on ETRAX_ARCH_V32 - help - This option enables the I2C driver used by e.g. the RTC driver. - -config ETRAX_V32_I2C_DATA_PORT - string "I2C data pin" - depends on ETRAX_I2C - help - The pin to use for I2C data. - -config ETRAX_V32_I2C_CLK_PORT - string "I2C clock pin" - depends on ETRAX_I2C - help - The pin to use for I2C clock. - -config ETRAX_GPIO - bool "GPIO support" - depends on ETRAX_ARCH_V32 - ---help--- - Enables the ETRAX general port device (major 120, minors 0-4). - You can use this driver to access the general port bits. It supports - these ioctl's: - #include <linux/etraxgpio.h> - fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob - ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set); - ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear); - err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val); - Remember that you need to setup the port directions appropriately in - the General configuration. - -config ETRAX_VIRTUAL_GPIO - bool "Virtual GPIO support" - depends on ETRAX_GPIO - help - Enables the virtual Etrax general port device (major 120, minor 6). - It uses an I/O expander for the I2C-bus. - -config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN - int "Virtual GPIO interrupt pin on PA pin" - range 0 7 - depends on ETRAX_VIRTUAL_GPIO - help - The pin to use on PA for virtual gpio interrupt. - -config ETRAX_PA_CHANGEABLE_DIR - hex "PA user changeable dir mask" - depends on ETRAX_GPIO - default "0x00" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PA that a - user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0 here, but it depends on your hardware. - -config ETRAX_PA_CHANGEABLE_BITS - hex "PA user changeable bits mask" - depends on ETRAX_GPIO - default "0x00" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PA - that a user can change the value on using ioctl's. - Bit set = changeable. - -config ETRAX_PB_CHANGEABLE_DIR - hex "PB user changeable dir mask" - depends on ETRAX_GPIO - default "0x00000" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PB - that a user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0 here, but it depends on your hardware. - -config ETRAX_PB_CHANGEABLE_BITS - hex "PB user changeable bits mask" - depends on ETRAX_GPIO - default "0x00000" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PB - that a user can change the value on using ioctl's. - Bit set = changeable. - -config ETRAX_PC_CHANGEABLE_DIR - hex "PC user changeable dir mask" - depends on ETRAX_GPIO - default "0x00000" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PC - that a user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0 here, but it depends on your hardware. - -config ETRAX_PC_CHANGEABLE_BITS - hex "PC user changeable bits mask" - depends on ETRAX_GPIO - default "0x00000" if ETRAXFS - default "0x00000000" if !ETRAXFS - help - This is a bitmask with information of what bits in PC - that a user can change the value on using ioctl's. - Bit set = changeable. - -config ETRAX_PD_CHANGEABLE_DIR - hex "PD user changeable dir mask" - depends on ETRAX_GPIO && ETRAXFS - default "0x00000" - help - This is a bitmask with information of what bits in PD - that a user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0x00000 here, but it depends on your hardware. - -config ETRAX_PD_CHANGEABLE_BITS - hex "PD user changeable bits mask" - depends on ETRAX_GPIO && ETRAXFS - default "0x00000" - help - This is a bitmask (18 bits) with information of what bits in PD - that a user can change the value on using ioctl's. - Bit set = changeable. - -config ETRAX_PE_CHANGEABLE_DIR - hex "PE user changeable dir mask" - depends on ETRAX_GPIO && ETRAXFS - default "0x00000" - help - This is a bitmask (18 bits) with information of what bits in PE - that a user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0x00000 here, but it depends on your hardware. - -config ETRAX_PE_CHANGEABLE_BITS - hex "PE user changeable bits mask" - depends on ETRAX_GPIO && ETRAXFS - default "0x00000" - help - This is a bitmask (18 bits) with information of what bits in PE - that a user can change the value on using ioctl's. - Bit set = changeable. - -config ETRAX_PV_CHANGEABLE_DIR - hex "PV user changeable dir mask" - depends on ETRAX_VIRTUAL_GPIO - default "0x0000" - help - This is a bitmask (16 bits) with information of what bits in PV - that a user can change direction on using ioctl's. - Bit set = changeable. - You probably want 0x0000 here, but it depends on your hardware. - -config ETRAX_PV_CHANGEABLE_BITS - hex "PV user changeable bits mask" - depends on ETRAX_VIRTUAL_GPIO - default "0x0000" - help - This is a bitmask (16 bits) with information of what bits in PV - that a user can change the value on using ioctl's. - Bit set = changeable. - config ETRAX_CARDBUS bool "Cardbus support" depends on ETRAX_ARCH_V32 |