1 files changed, 110 insertions, 0 deletions
diff --git a/arch/cris/arch-v32/mach-a3/Kconfig b/arch/cris/arch-v32/mach-a3/Kconfig
new file mode 100644
index 000000000..87547271a
--- /dev/null
+++ b/arch/cris/arch-v32/mach-a3/Kconfig
@@ -0,0 +1,110 @@
+if CRIS_MACH_ARTPEC3
+
+menu "Artpec-3 options"
+       depends on CRIS_MACH_ARTPEC3
+
+config ETRAX_DRAM_VIRTUAL_BASE
+	hex
+	default "c0000000"
+
+config ETRAX_L2CACHE
+       bool
+       default y
+
+config ETRAX_SERIAL_PORTS
+       int
+       default 5
+
+config ETRAX_DDR2_MRS
+	hex "DDR2 MRS"
+	default "0"
+
+config ETRAX_DDR2_TIMING
+	hex "DDR2 SDRAM timing"
+	default "0"
+	help
+	  SDRAM timing parameters.
+
+config ETRAX_DDR2_CONFIG
+	hex "DDR2 config"
+	default "0"
+
+config ETRAX_DDR2_LATENCY
+	hex "DDR2 latency"
+	default "0"
+
+config ETRAX_PIO_CE0_CFG
+       hex "PIO CE0 configuration"
+       default "0"
+
+config ETRAX_PIO_CE1_CFG
+       hex "PIO CE1 configuration"
+       default "0"
+
+config ETRAX_PIO_CE2_CFG
+       hex "PIO CE2 configuration"
+       default "0"
+
+config ETRAX_DEF_GIO_PA_OE
+	hex "GIO_PA_OE"
+	default "00000000"
+	help
+	  Configures the direction of general port A bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PA_OUT
+	hex "GIO_PA_OUT"
+	default "00000000"
+	help
+	  Configures the initial data for the general port A bits.  Most
+	  products should use 00 here.
+
+config ETRAX_DEF_GIO_PB_OE
+	hex "GIO_PB_OE"
+	default "000000000"
+	help
+	  Configures the direction of general port B bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PB_OUT
+	hex "GIO_PB_OUT"
+	default "000000000"
+	help
+	  Configures the initial data for the general port B bits.  Most
+	  products should use 00000 here.
+
+config ETRAX_DEF_GIO_PC_OE
+	hex "GIO_PC_OE"
+	default "00000"
+	help
+	  Configures the direction of general port C bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PC_OUT
+	hex "GIO_PC_OUT"
+	default "00000"
+	help
+	  Configures the initial data for the general port C bits.  Most
+	  products should use 00000 here.
+
+endmenu
+
+endif