diff options
Diffstat (limited to 'arch/mips/loongson/lemote-2f/reset.c')
| -rw-r--r-- | arch/mips/loongson/lemote-2f/reset.c | 159 |
1 files changed, 159 insertions, 0 deletions
diff --git a/arch/mips/loongson/lemote-2f/reset.c b/arch/mips/loongson/lemote-2f/reset.c new file mode 100644 index 000000000..a26ca7fcd --- /dev/null +++ b/arch/mips/loongson/lemote-2f/reset.c @@ -0,0 +1,159 @@ +/* Board-specific reboot/shutdown routines + * + * Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca> + * + * Copyright (C) 2009 Lemote Inc. + * Author: Wu Zhangjin, wuzhangjin@gmail.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/io.h> +#include <linux/delay.h> +#include <linux/types.h> + +#include <asm/bootinfo.h> + +#include <loongson.h> + +#include <cs5536/cs5536.h> +#include "ec_kb3310b.h" + +static void reset_cpu(void) +{ + /* + * reset cpu to full speed, this is needed when enabling cpu frequency + * scalling + */ + LOONGSON_CHIPCFG(0) |= 0x7; +} + +/* reset support for fuloong2f */ + +static void fl2f_reboot(void) +{ + reset_cpu(); + + /* send a reset signal to south bridge. + * + * NOTE: if enable "Power Management" in kernel, rtl8169 will not reset + * normally with this reset operation and it will not work in PMON, but + * you can type halt command and then reboot, seems the hardware reset + * logic not work normally. + */ + { + u32 hi, lo; + _rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo); + lo |= 0x00000001; + _wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo); + } +} + +static void fl2f_shutdown(void) +{ + u32 hi, lo, val; + int gpio_base; + + /* get gpio base */ + _rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo); + gpio_base = lo & 0xff00; + + /* make cs5536 gpio13 output enable */ + val = inl(gpio_base + GPIOL_OUT_EN); + val &= ~(1 << (16 + 13)); + val |= (1 << 13); + outl(val, gpio_base + GPIOL_OUT_EN); + mmiowb(); + /* make cs5536 gpio13 output low level voltage. */ + val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13)); + val |= (1 << (16 + 13)); + outl(val, gpio_base + GPIOL_OUT_VAL); + mmiowb(); +} + +/* reset support for yeeloong2f and mengloong2f notebook */ + +static void ml2f_reboot(void) +{ + reset_cpu(); + + /* sending an reset signal to EC(embedded controller) */ + ec_write(REG_RESET, BIT_RESET_ON); +} + +#define yl2f89_reboot ml2f_reboot + +/* menglong(7inches) laptop has different shutdown logic from 8.9inches */ +#define EC_SHUTDOWN_IO_PORT_HIGH 0xff2d +#define EC_SHUTDOWN_IO_PORT_LOW 0xff2e +#define EC_SHUTDOWN_IO_PORT_DATA 0xff2f +#define REG_SHUTDOWN_HIGH 0xFC +#define REG_SHUTDOWN_LOW 0x29 +#define BIT_SHUTDOWN_ON (1 << 1) + +static void ml2f_shutdown(void) +{ + u8 val; + u64 i; + + outb(REG_SHUTDOWN_HIGH, EC_SHUTDOWN_IO_PORT_HIGH); + outb(REG_SHUTDOWN_LOW, EC_SHUTDOWN_IO_PORT_LOW); + mmiowb(); + val = inb(EC_SHUTDOWN_IO_PORT_DATA); + outb(val & (~BIT_SHUTDOWN_ON), EC_SHUTDOWN_IO_PORT_DATA); + mmiowb(); + /* need enough wait here... how many microseconds needs? */ + for (i = 0; i < 0x10000; i++) + delay(); + outb(val | BIT_SHUTDOWN_ON, EC_SHUTDOWN_IO_PORT_DATA); + mmiowb(); +} + +static void yl2f89_shutdown(void) +{ + /* cpu-gpio0 output low */ + LOONGSON_GPIODATA &= ~0x00000001; + /* cpu-gpio0 as output */ + LOONGSON_GPIOIE &= ~0x00000001; +} + +void mach_prepare_reboot(void) +{ + switch (mips_machtype) { + case MACH_LEMOTE_FL2F: + case MACH_LEMOTE_NAS: + case MACH_LEMOTE_LL2F: + fl2f_reboot(); + break; + case MACH_LEMOTE_ML2F7: + ml2f_reboot(); + break; + case MACH_LEMOTE_YL2F89: + yl2f89_reboot(); + break; + default: + break; + } +} + +void mach_prepare_shutdown(void) +{ + switch (mips_machtype) { + case MACH_LEMOTE_FL2F: + case MACH_LEMOTE_NAS: + case MACH_LEMOTE_LL2F: + fl2f_shutdown(); + break; + case MACH_LEMOTE_ML2F7: + ml2f_shutdown(); + break; + case MACH_LEMOTE_YL2F89: + yl2f89_shutdown(); + break; + default: + break; + } +} |