diff options
Diffstat (limited to 'arch/powerpc/platforms/Kconfig')
| -rw-r--r-- | arch/powerpc/platforms/Kconfig | 359 |
1 files changed, 359 insertions, 0 deletions
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig new file mode 100644 index 000000000..b7f9c408b --- /dev/null +++ b/arch/powerpc/platforms/Kconfig @@ -0,0 +1,359 @@ +menu "Platform support" + +source "arch/powerpc/platforms/powernv/Kconfig" +source "arch/powerpc/platforms/pseries/Kconfig" +source "arch/powerpc/platforms/chrp/Kconfig" +source "arch/powerpc/platforms/512x/Kconfig" +source "arch/powerpc/platforms/52xx/Kconfig" +source "arch/powerpc/platforms/powermac/Kconfig" +source "arch/powerpc/platforms/maple/Kconfig" +source "arch/powerpc/platforms/pasemi/Kconfig" +source "arch/powerpc/platforms/ps3/Kconfig" +source "arch/powerpc/platforms/cell/Kconfig" +source "arch/powerpc/platforms/8xx/Kconfig" +source "arch/powerpc/platforms/82xx/Kconfig" +source "arch/powerpc/platforms/83xx/Kconfig" +source "arch/powerpc/platforms/85xx/Kconfig" +source "arch/powerpc/platforms/86xx/Kconfig" +source "arch/powerpc/platforms/embedded6xx/Kconfig" +source "arch/powerpc/platforms/44x/Kconfig" +source "arch/powerpc/platforms/40x/Kconfig" +source "arch/powerpc/platforms/amigaone/Kconfig" + +config KVM_GUEST + bool "KVM Guest support" + default n + select EPAPR_PARAVIRT + ---help--- + This option enables various optimizations for running under the KVM + hypervisor. Overhead for the kernel when not running inside KVM should + be minimal. + + In case of doubt, say Y + +config EPAPR_PARAVIRT + bool "ePAPR para-virtualization support" + default n + help + Enables ePAPR para-virtualization support for guests. + + In case of doubt, say Y + +config PPC_NATIVE + bool + depends on 6xx || PPC64 + help + Support for running natively on the hardware, i.e. without + a hypervisor. This option is not user-selectable but should + be selected by all platforms that need it. + +config PPC_OF_BOOT_TRAMPOLINE + bool "Support booting from Open Firmware or yaboot" + depends on 6xx || PPC64 + default y + help + Support from booting from Open Firmware or yaboot using an + Open Firmware client interface. This enables the kernel to + communicate with open firmware to retrieve system information + such as the device tree. + + In case of doubt, say Y + +config UDBG_RTAS_CONSOLE + bool "RTAS based debug console" + depends on PPC_RTAS + default n + +config PPC_SMP_MUXED_IPI + bool + help + Select this opton if your platform supports SMP and your + interrupt controller provides less than 4 interrupts to each + cpu. This will enable the generic code to multiplex the 4 + messages on to one ipi. + +config IPIC + bool + default n + +config MPIC + bool + default n + +config MPIC_TIMER + bool "MPIC Global Timer" + depends on MPIC && FSL_SOC + default n + help + The MPIC global timer is a hardware timer inside the + Freescale PIC complying with OpenPIC standard. When the + specified interval times out, the hardware timer generates + an interrupt. The driver currently is only tested on fsl + chip, but it can potentially support other global timers + complying with the OpenPIC standard. + +config FSL_MPIC_TIMER_WAKEUP + tristate "Freescale MPIC global timer wakeup driver" + depends on FSL_SOC && MPIC_TIMER && PM + default n + help + The driver provides a way to wake up the system by MPIC + timer. + e.g. "echo 5 > /sys/devices/system/mpic/timer_wakeup" + +config PPC_EPAPR_HV_PIC + bool + default n + select EPAPR_PARAVIRT + +config MPIC_WEIRD + bool + default n + +config MPIC_MSGR + bool "MPIC message register support" + depends on MPIC + default n + help + Enables support for the MPIC message registers. These + registers are used for inter-processor communication. + +config PPC_I8259 + bool + default n + +config U3_DART + bool + depends on PPC64 + default n + +config PPC_RTAS + bool + default n + +config RTAS_ERROR_LOGGING + bool + depends on PPC_RTAS + default n + +config PPC_RTAS_DAEMON + bool + depends on PPC_RTAS + default n + +config RTAS_PROC + bool "Proc interface to RTAS" + depends on PPC_RTAS && PROC_FS + default y + +config RTAS_FLASH + tristate "Firmware flash interface" + depends on PPC64 && RTAS_PROC + +config MMIO_NVRAM + bool + default n + +config MPIC_U3_HT_IRQS + bool + default n + +config MPIC_BROKEN_REGREAD + bool + depends on MPIC + help + This option enables a MPIC driver workaround for some chips + that have a bug that causes some interrupt source information + to not read back properly. It is safe to use on other chips as + well, but enabling it uses about 8KB of memory to keep copies + of the register contents in software. + +config IBMVIO + depends on PPC_PSERIES + bool + default y + +config IBMEBUS + depends on PPC_PSERIES + bool "Support for GX bus based adapters" + help + Bus device driver for GX bus based adapters. + +config EEH + bool + depends on (PPC_POWERNV || PPC_PSERIES) && PCI + default y + +config PPC_MPC106 + bool + default n + +config PPC_970_NAP + bool + default n + +config PPC_P7_NAP + bool + default n + +config PPC_INDIRECT_PIO + bool + select GENERIC_IOMAP + +config PPC_INDIRECT_MMIO + bool + +config PPC_IO_WORKAROUNDS + bool + +source "drivers/cpufreq/Kconfig" + +menu "CPUIdle driver" + +source "drivers/cpuidle/Kconfig" + +endmenu + +config PPC601_SYNC_FIX + bool "Workarounds for PPC601 bugs" + depends on 6xx && PPC_PMAC + help + Some versions of the PPC601 (the first PowerPC chip) have bugs which + mean that extra synchronization instructions are required near + certain instructions, typically those that make major changes to the + CPU state. These extra instructions reduce performance slightly. + If you say N here, these extra instructions will not be included, + resulting in a kernel which will run faster but may not run at all + on some systems with the PPC601 chip. + + If in doubt, say Y here. + +config TAU + bool "On-chip CPU temperature sensor support" + depends on 6xx + help + G3 and G4 processors have an on-chip temperature sensor called the + 'Thermal Assist Unit (TAU)', which, in theory, can measure the on-die + temperature within 2-4 degrees Celsius. This option shows the current + on-die temperature in /proc/cpuinfo if the cpu supports it. + + Unfortunately, on some chip revisions, this sensor is very inaccurate + and in many cases, does not work at all, so don't assume the cpu + temp is actually what /proc/cpuinfo says it is. + +config TAU_INT + bool "Interrupt driven TAU driver (DANGEROUS)" + depends on TAU + ---help--- + The TAU supports an interrupt driven mode which causes an interrupt + whenever the temperature goes out of range. This is the fastest way + to get notified the temp has exceeded a range. With this option off, + a timer is used to re-check the temperature periodically. + + However, on some cpus it appears that the TAU interrupt hardware + is buggy and can cause a situation which would lead unexplained hard + lockups. + + Unless you are extending the TAU driver, or enjoy kernel/hardware + debugging, leave this option off. + +config TAU_AVERAGE + bool "Average high and low temp" + depends on TAU + ---help--- + The TAU hardware can compare the temperature to an upper and lower + bound. The default behavior is to show both the upper and lower + bound in /proc/cpuinfo. If the range is large, the temperature is + either changing a lot, or the TAU hardware is broken (likely on some + G4's). If the range is small (around 4 degrees), the temperature is + relatively stable. If you say Y here, a single temperature value, + halfway between the upper and lower bounds, will be reported in + /proc/cpuinfo. + + If in doubt, say N here. + +config QUICC_ENGINE + bool "Freescale QUICC Engine (QE) Support" + depends on FSL_SOC && PPC32 + select PPC_LIB_RHEAP + select CRC32 + help + The QUICC Engine (QE) is a new generation of communications + coprocessors on Freescale embedded CPUs (akin to CPM in older chips). + Selecting this option means that you wish to build a kernel + for a machine with a QE coprocessor. + +config QE_GPIO + bool "QE GPIO support" + depends on QUICC_ENGINE + select ARCH_REQUIRE_GPIOLIB + help + Say Y here if you're going to use hardware that connects to the + QE GPIOs. + +config CPM2 + bool "Enable support for the CPM2 (Communications Processor Module)" + depends on (FSL_SOC_BOOKE && PPC32) || 8260 + select CPM + select PPC_LIB_RHEAP + select PPC_PCI_CHOICE + select ARCH_REQUIRE_GPIOLIB + help + The CPM2 (Communications Processor Module) is a coprocessor on + embedded CPUs made by Freescale. Selecting this option means that + you wish to build a kernel for a machine with a CPM2 coprocessor + on it (826x, 827x, 8560). + +config AXON_RAM + tristate "Axon DDR2 memory device driver" + depends on PPC_IBM_CELL_BLADE && BLOCK + default m + help + It registers one block device per Axon's DDR2 memory bank found + on a system. Block devices are called axonram?, their major and + minor numbers are available in /proc/devices, /proc/partitions or + in /sys/block/axonram?/dev. + +config FSL_ULI1575 + bool + default n + select GENERIC_ISA_DMA + help + Supports for the ULI1575 PCIe south bridge that exists on some + Freescale reference boards. The boards all use the ULI in pretty + much the same way. + +config CPM + bool + +config OF_RTC + bool + help + Uses information from the OF or flattened device tree to instantiate + platform devices for direct mapped RTC chips like the DS1742 or DS1743. + +config SIMPLE_GPIO + bool "Support for simple, memory-mapped GPIO controllers" + depends on PPC + select ARCH_REQUIRE_GPIOLIB + help + Say Y here to support simple, memory-mapped GPIO controllers. + These are usually BCSRs used to control board's switches, LEDs, + chip-selects, Ethernet/USB PHY's power and various other small + on-board peripherals. + +config MCU_MPC8349EMITX + bool "MPC8349E-mITX MCU driver" + depends on I2C=y && PPC_83xx + select ARCH_REQUIRE_GPIOLIB + help + Say Y here to enable soft power-off functionality on the Freescale + boards with the MPC8349E-mITX-compatible MCU chips. This driver will + also register MCU GPIOs with the generic GPIO API, so you'll able + to use MCU pins as GPIOs. + +config XILINX_PCI + bool "Xilinx PCI host bridge support" + depends on PCI && XILINX_VIRTEX + +endmenu |