diff options
Diffstat (limited to 'drivers/ata/pata_cs5530.c')
| -rw-r--r-- | drivers/ata/pata_cs5530.c | 369 |
1 files changed, 369 insertions, 0 deletions
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c new file mode 100644 index 000000000..f9ca72e93 --- /dev/null +++ b/drivers/ata/pata_cs5530.c @@ -0,0 +1,369 @@ +/* + * pata-cs5530.c - CS5530 PATA for new ATA layer + * (C) 2005 Red Hat Inc + * + * based upon cs5530.c by Mark Lord. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Loosely based on the piix & svwks drivers. + * + * Documentation: + * Available from AMD web site. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/dmi.h> + +#define DRV_NAME "pata_cs5530" +#define DRV_VERSION "0.7.4" + +static void __iomem *cs5530_port_base(struct ata_port *ap) +{ + unsigned long bmdma = (unsigned long)ap->ioaddr.bmdma_addr; + + return (void __iomem *)((bmdma & ~0x0F) + 0x20 + 0x10 * ap->port_no); +} + +/** + * cs5530_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the CS5530 + * chips. + */ + +static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const unsigned int cs5530_pio_timings[2][5] = { + {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, + {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010} + }; + void __iomem *base = cs5530_port_base(ap); + u32 tuning; + int format; + + /* Find out which table to use */ + tuning = ioread32(base + 0x04); + format = (tuning & 0x80000000UL) ? 1 : 0; + + /* Now load the right timing register */ + if (adev->devno) + base += 0x08; + + iowrite32(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base); +} + +/** + * cs5530_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * We cannot mix MWDMA and UDMA without reloading timings each switch + * master to slave. We track the last DMA setup in order to minimise + * reloads. + */ + +static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + void __iomem *base = cs5530_port_base(ap); + u32 tuning, timing = 0; + u8 reg; + + /* Find out which table to use */ + tuning = ioread32(base + 0x04); + + switch(adev->dma_mode) { + case XFER_UDMA_0: + timing = 0x00921250;break; + case XFER_UDMA_1: + timing = 0x00911140;break; + case XFER_UDMA_2: + timing = 0x00911030;break; + case XFER_MW_DMA_0: + timing = 0x00077771;break; + case XFER_MW_DMA_1: + timing = 0x00012121;break; + case XFER_MW_DMA_2: + timing = 0x00002020;break; + default: + BUG(); + } + /* Merge in the PIO format bit */ + timing |= (tuning & 0x80000000UL); + if (adev->devno == 0) /* Master */ + iowrite32(timing, base + 0x04); + else { + if (timing & 0x00100000) + tuning |= 0x00100000; /* UDMA for both */ + else + tuning &= ~0x00100000; /* MWDMA for both */ + iowrite32(tuning, base + 0x04); + iowrite32(timing, base + 0x0C); + } + + /* Set the DMA capable bit in the BMDMA area */ + reg = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + reg |= (1 << (5 + adev->devno)); + iowrite8(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + + /* Remember the last DMA setup we did */ + + ap->private_data = adev; +} + +/** + * cs5530_qc_issue - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * necessary. Specifically we have a problem that there is only + * one MWDMA/UDMA bit. + */ + +static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_device *prev = ap->private_data; + + /* See if the DMA settings could be wrong */ + if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { + /* Maybe, but do the channels match MWDMA/UDMA ? */ + if ((ata_using_udma(adev) && !ata_using_udma(prev)) || + (ata_using_udma(prev) && !ata_using_udma(adev))) + /* Switch the mode bits */ + cs5530_set_dmamode(ap, adev); + } + + return ata_bmdma_qc_issue(qc); +} + +static struct scsi_host_template cs5530_sht = { + ATA_BMDMA_SHT(DRV_NAME), + .sg_tablesize = LIBATA_DUMB_MAX_PRD, +}; + +static struct ata_port_operations cs5530_port_ops = { + .inherits = &ata_bmdma_port_ops, + + .qc_prep = ata_bmdma_dumb_qc_prep, + .qc_issue = cs5530_qc_issue, + + .cable_detect = ata_cable_40wire, + .set_piomode = cs5530_set_piomode, + .set_dmamode = cs5530_set_dmamode, +}; + +static const struct dmi_system_id palmax_dmi_table[] = { + { + .ident = "Palmax PD1100", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Cyrix"), + DMI_MATCH(DMI_PRODUCT_NAME, "Caddis"), + }, + }, + { } +}; + +static int cs5530_is_palmax(void) +{ + if (dmi_check_system(palmax_dmi_table)) { + printk(KERN_INFO "Palmax PD1100: Disabling DMA on docking port.\n"); + return 1; + } + return 0; +} + + +/** + * cs5530_init_chip - Chipset init + * + * Perform the chip initialisation work that is shared between both + * setup and resume paths + */ + +static int cs5530_init_chip(void) +{ + struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL; + + while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) { + switch (dev->device) { + case PCI_DEVICE_ID_CYRIX_PCI_MASTER: + master_0 = pci_dev_get(dev); + break; + case PCI_DEVICE_ID_CYRIX_5530_LEGACY: + cs5530_0 = pci_dev_get(dev); + break; + } + } + if (!master_0) { + printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n"); + goto fail_put; + } + if (!cs5530_0) { + printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n"); + goto fail_put; + } + + pci_set_master(cs5530_0); + pci_try_set_mwi(cs5530_0); + + /* + * Set PCI CacheLineSize to 16-bytes: + * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530 + * + * Note: This value is constant because the 5530 is only a Geode companion + */ + + pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04); + + /* + * Disable trapping of UDMA register accesses (Win98 hack): + * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530 + */ + + pci_write_config_word(cs5530_0, 0xd0, 0x5006); + + /* + * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus: + * The other settings are what is necessary to get the register + * into a sane state for IDE DMA operation. + */ + + pci_write_config_byte(master_0, 0x40, 0x1e); + + /* + * Set max PCI burst size (16-bytes seems to work best): + * 16bytes: set bit-1 at 0x41 (reg value of 0x16) + * all others: clear bit-1 at 0x41, and do: + * 128bytes: OR 0x00 at 0x41 + * 256bytes: OR 0x04 at 0x41 + * 512bytes: OR 0x08 at 0x41 + * 1024bytes: OR 0x0c at 0x41 + */ + + pci_write_config_byte(master_0, 0x41, 0x14); + + /* + * These settings are necessary to get the chip + * into a sane state for IDE DMA operation. + */ + + pci_write_config_byte(master_0, 0x42, 0x00); + pci_write_config_byte(master_0, 0x43, 0xc1); + + pci_dev_put(master_0); + pci_dev_put(cs5530_0); + return 0; +fail_put: + pci_dev_put(master_0); + pci_dev_put(cs5530_0); + return -ENODEV; +} + +/** + * cs5530_init_one - Initialise a CS5530 + * @dev: PCI device + * @id: Entry in match table + * + * Install a driver for the newly found CS5530 companion chip. Most of + * this is just housekeeping. We have to set the chip up correctly and + * turn off various bits of emulation magic. + */ + +static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, + .port_ops = &cs5530_port_ops + }; + /* The docking connector doesn't do UDMA, and it seems not MWDMA */ + static const struct ata_port_info info_palmax_secondary = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .port_ops = &cs5530_port_ops + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + int rc; + + rc = pcim_enable_device(pdev); + if (rc) + return rc; + + /* Chip initialisation */ + if (cs5530_init_chip()) + return -ENODEV; + + if (cs5530_is_palmax()) + ppi[1] = &info_palmax_secondary; + + /* Now kick off ATA set up */ + return ata_pci_bmdma_init_one(pdev, ppi, &cs5530_sht, NULL, 0); +} + +#ifdef CONFIG_PM_SLEEP +static int cs5530_reinit_one(struct pci_dev *pdev) +{ + struct ata_host *host = pci_get_drvdata(pdev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + /* If we fail on resume we are doomed */ + if (cs5530_init_chip()) + return -EIO; + + ata_host_resume(host); + return 0; +} +#endif /* CONFIG_PM_SLEEP */ + +static const struct pci_device_id cs5530[] = { + { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), }, + + { }, +}; + +static struct pci_driver cs5530_pci_driver = { + .name = DRV_NAME, + .id_table = cs5530, + .probe = cs5530_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = cs5530_reinit_one, +#endif +}; + +module_pci_driver(cs5530_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, cs5530); +MODULE_VERSION(DRV_VERSION); |