1 files changed, 273 insertions, 0 deletions
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
new file mode 100644
index 000000000..b9bf78b7d
--- /dev/null
+++ b/drivers/ata/pata_oldpiix.c
@@ -0,0 +1,273 @@
+/*
+ *    pata_oldpiix.c - Intel PATA/SATA controllers
+ *
+ *	(C) 2005 Red Hat
+ *
+ *    Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ *    Early PIIX differs significantly from the later PIIX as it lacks
+ *    SITRE and the slave timing registers. This means that you have to
+ *    set timing per channel, or be clever. Libata tells us whenever it
+ *    does drive selection and we use this to reload the timings.
+ *
+ *    Because of these behaviour differences PIIX gets its own driver module.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME	"pata_oldpiix"
+#define DRV_VERSION	"0.5.5"
+
+/**
+ *	oldpiix_pre_reset		-	probe begin
+ *	@link: ATA link
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Set up cable type and use generic probe init
+ */
+
+static int oldpiix_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	static const struct pci_bits oldpiix_enable_bits[] = {
+		{ 0x41U, 1U, 0x80UL, 0x80UL },	/* port 0 */
+		{ 0x43U, 1U, 0x80UL, 0x80UL },	/* port 1 */
+	};
+
+	if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no]))
+		return -ENOENT;
+
+	return ata_sff_prereset(link, deadline);
+}
+
+/**
+ *	oldpiix_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device whose timings we are configuring
+ *
+ *	Set PIO mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
+	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+	u16 idetm_data;
+	int control = 0;
+
+	/*
+	 *	See Intel Document 298600-004 for the timing programing rules
+	 *	for PIIX/ICH. Note that the early PIIX does not have the slave
+	 *	timing port at 0x44.
+	 */
+
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },
+			    { 0, 0 },
+			    { 1, 0 },
+			    { 2, 1 },
+			    { 2, 3 }, };
+
+	if (pio > 1)
+		control |= 1;	/* TIME */
+	if (ata_pio_need_iordy(adev))
+		control |= 2;	/* IE */
+
+	/* Intel specifies that the prefetch/posting is for disk only */
+	if (adev->class == ATA_DEV_ATA)
+		control |= 4;	/* PPE */
+
+	pci_read_config_word(dev, idetm_port, &idetm_data);
+
+	/*
+	 * Set PPE, IE and TIME as appropriate.
+	 * Clear the other drive's timing bits.
+	 */
+	if (adev->devno == 0) {
+		idetm_data &= 0xCCE0;
+		idetm_data |= control;
+	} else {
+		idetm_data &= 0xCC0E;
+		idetm_data |= (control << 4);
+	}
+	idetm_data |= (timings[pio][0] << 12) |
+			(timings[pio][1] << 8);
+	pci_write_config_word(dev, idetm_port, idetm_data);
+
+	/* Track which port is configured */
+	ap->private_data = adev;
+}
+
+/**
+ *	oldpiix_set_dmamode - Initialize host controller PATA DMA timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device to program
+ *
+ *	Set MWDMA mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	u8 idetm_port		= ap->port_no ? 0x42 : 0x40;
+	u16 idetm_data;
+
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },
+			    { 0, 0 },
+			    { 1, 0 },
+			    { 2, 1 },
+			    { 2, 3 }, };
+
+	/*
+	 * MWDMA is driven by the PIO timings. We must also enable
+	 * IORDY unconditionally along with TIME1. PPE has already
+	 * been set when the PIO timing was set.
+	 */
+
+	unsigned int mwdma	= adev->dma_mode - XFER_MW_DMA_0;
+	unsigned int control;
+	const unsigned int needed_pio[3] = {
+		XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+	};
+	int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+	pci_read_config_word(dev, idetm_port, &idetm_data);
+
+	control = 3;	/* IORDY|TIME0 */
+	/* Intel specifies that the PPE functionality is for disk only */
+	if (adev->class == ATA_DEV_ATA)
+		control |= 4;	/* PPE enable */
+
+	/* If the drive MWDMA is faster than it can do PIO then
+	   we must force PIO into PIO0 */
+
+	if (adev->pio_mode < needed_pio[mwdma])
+		/* Enable DMA timing only */
+		control |= 8;	/* PIO cycles in PIO0 */
+
+	/* Mask out the relevant control and timing bits we will load. Also
+	   clear the other drive TIME register as a precaution */
+	if (adev->devno == 0) {
+		idetm_data &= 0xCCE0;
+		idetm_data |= control;
+	} else {
+		idetm_data &= 0xCC0E;
+		idetm_data |= (control << 4);
+	}
+	idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+	pci_write_config_word(dev, idetm_port, idetm_data);
+
+	/* Track which port is configured */
+	ap->private_data = adev;
+}
+
+/**
+ *	oldpiix_qc_issue	-	command issue
+ *	@qc: command pending
+ *
+ *	Called when the libata layer is about to issue a command. We wrap
+ *	this interface so that we can load the correct ATA timings if
+ *	necessary. Our logic also clears TIME0/TIME1 for the other device so
+ *	that, even if we get this wrong, cycles to the other device will
+ *	be made PIO0.
+ */
+
+static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct ata_device *adev = qc->dev;
+
+	if (adev != ap->private_data) {
+		oldpiix_set_piomode(ap, adev);
+		if (ata_dma_enabled(adev))
+			oldpiix_set_dmamode(ap, adev);
+	}
+	return ata_bmdma_qc_issue(qc);
+}
+
+
+static struct scsi_host_template oldpiix_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations oldpiix_pata_ops = {
+	.inherits		= &ata_bmdma_port_ops,
+	.qc_issue		= oldpiix_qc_issue,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= oldpiix_set_piomode,
+	.set_dmamode		= oldpiix_set_dmamode,
+	.prereset		= oldpiix_pre_reset,
+};
+
+
+/**
+ *	oldpiix_init_one - Register PIIX ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in oldpiix_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *	and then hand over control to libata, for it to do the rest.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static const struct ata_port_info info = {
+		.flags		= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA12_ONLY,
+		.port_ops	= &oldpiix_pata_ops,
+	};
+	const struct ata_port_info *ppi[] = { &info, NULL };
+
+	ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+	return ata_pci_bmdma_init_one(pdev, ppi, &oldpiix_sht, NULL, 0);
+}
+
+static const struct pci_device_id oldpiix_pci_tbl[] = {
+	{ PCI_VDEVICE(INTEL, 0x1230), },
+
+	{ }	/* terminate list */
+};
+
+static struct pci_driver oldpiix_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= oldpiix_pci_tbl,
+	.probe			= oldpiix_init_one,
+	.remove			= ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+	.suspend		= ata_pci_device_suspend,
+	.resume			= ata_pci_device_resume,
+#endif
+};
+
+module_pci_driver(oldpiix_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);