diff options
Diffstat (limited to 'drivers/clk/clk-u300.c')
| -rw-r--r-- | drivers/clk/clk-u300.c | 1195 |
1 files changed, 1195 insertions, 0 deletions
diff --git a/drivers/clk/clk-u300.c b/drivers/clk/clk-u300.c new file mode 100644 index 000000000..406bfc137 --- /dev/null +++ b/drivers/clk/clk-u300.c @@ -0,0 +1,1195 @@ +/* + * U300 clock implementation + * Copyright (C) 2007-2012 ST-Ericsson AB + * License terms: GNU General Public License (GPL) version 2 + * Author: Linus Walleij <linus.walleij@stericsson.com> + * Author: Jonas Aaberg <jonas.aberg@stericsson.com> + */ +#include <linux/clk.h> +#include <linux/clkdev.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/clk-provider.h> +#include <linux/spinlock.h> +#include <linux/of.h> + +/* APP side SYSCON registers */ +/* CLK Control Register 16bit (R/W) */ +#define U300_SYSCON_CCR (0x0000) +#define U300_SYSCON_CCR_I2S1_USE_VCXO (0x0040) +#define U300_SYSCON_CCR_I2S0_USE_VCXO (0x0020) +#define U300_SYSCON_CCR_TURN_VCXO_ON (0x0008) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK (0x0007) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER (0x04) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW (0x03) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE (0x02) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH (0x01) +#define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST (0x00) +/* CLK Status Register 16bit (R/W) */ +#define U300_SYSCON_CSR (0x0004) +#define U300_SYSCON_CSR_PLL208_LOCK_IND (0x0002) +#define U300_SYSCON_CSR_PLL13_LOCK_IND (0x0001) +/* Reset lines for SLOW devices 16bit (R/W) */ +#define U300_SYSCON_RSR (0x0014) +#define U300_SYSCON_RSR_PPM_RESET_EN (0x0200) +#define U300_SYSCON_RSR_ACC_TMR_RESET_EN (0x0100) +#define U300_SYSCON_RSR_APP_TMR_RESET_EN (0x0080) +#define U300_SYSCON_RSR_RTC_RESET_EN (0x0040) +#define U300_SYSCON_RSR_KEYPAD_RESET_EN (0x0020) +#define U300_SYSCON_RSR_GPIO_RESET_EN (0x0010) +#define U300_SYSCON_RSR_EH_RESET_EN (0x0008) +#define U300_SYSCON_RSR_BTR_RESET_EN (0x0004) +#define U300_SYSCON_RSR_UART_RESET_EN (0x0002) +#define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN (0x0001) +/* Reset lines for FAST devices 16bit (R/W) */ +#define U300_SYSCON_RFR (0x0018) +#define U300_SYSCON_RFR_UART1_RESET_ENABLE (0x0080) +#define U300_SYSCON_RFR_SPI_RESET_ENABLE (0x0040) +#define U300_SYSCON_RFR_MMC_RESET_ENABLE (0x0020) +#define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE (0x0010) +#define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE (0x0008) +#define U300_SYSCON_RFR_I2C1_RESET_ENABLE (0x0004) +#define U300_SYSCON_RFR_I2C0_RESET_ENABLE (0x0002) +#define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE (0x0001) +/* Reset lines for the rest of the peripherals 16bit (R/W) */ +#define U300_SYSCON_RRR (0x001c) +#define U300_SYSCON_RRR_CDS_RESET_EN (0x4000) +#define U300_SYSCON_RRR_ISP_RESET_EN (0x2000) +#define U300_SYSCON_RRR_INTCON_RESET_EN (0x1000) +#define U300_SYSCON_RRR_MSPRO_RESET_EN (0x0800) +#define U300_SYSCON_RRR_XGAM_RESET_EN (0x0100) +#define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN (0x0080) +#define U300_SYSCON_RRR_NANDIF_RESET_EN (0x0040) +#define U300_SYSCON_RRR_EMIF_RESET_EN (0x0020) +#define U300_SYSCON_RRR_DMAC_RESET_EN (0x0010) +#define U300_SYSCON_RRR_CPU_RESET_EN (0x0008) +#define U300_SYSCON_RRR_APEX_RESET_EN (0x0004) +#define U300_SYSCON_RRR_AHB_RESET_EN (0x0002) +#define U300_SYSCON_RRR_AAIF_RESET_EN (0x0001) +/* Clock enable for SLOW peripherals 16bit (R/W) */ +#define U300_SYSCON_CESR (0x0020) +#define U300_SYSCON_CESR_PPM_CLK_EN (0x0200) +#define U300_SYSCON_CESR_ACC_TMR_CLK_EN (0x0100) +#define U300_SYSCON_CESR_APP_TMR_CLK_EN (0x0080) +#define U300_SYSCON_CESR_KEYPAD_CLK_EN (0x0040) +#define U300_SYSCON_CESR_GPIO_CLK_EN (0x0010) +#define U300_SYSCON_CESR_EH_CLK_EN (0x0008) +#define U300_SYSCON_CESR_BTR_CLK_EN (0x0004) +#define U300_SYSCON_CESR_UART_CLK_EN (0x0002) +#define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN (0x0001) +/* Clock enable for FAST peripherals 16bit (R/W) */ +#define U300_SYSCON_CEFR (0x0024) +#define U300_SYSCON_CEFR_UART1_CLK_EN (0x0200) +#define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN (0x0100) +#define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN (0x0080) +#define U300_SYSCON_CEFR_SPI_CLK_EN (0x0040) +#define U300_SYSCON_CEFR_MMC_CLK_EN (0x0020) +#define U300_SYSCON_CEFR_I2S1_CLK_EN (0x0010) +#define U300_SYSCON_CEFR_I2S0_CLK_EN (0x0008) +#define U300_SYSCON_CEFR_I2C1_CLK_EN (0x0004) +#define U300_SYSCON_CEFR_I2C0_CLK_EN (0x0002) +#define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN (0x0001) +/* Clock enable for the rest of the peripherals 16bit (R/W) */ +#define U300_SYSCON_CERR (0x0028) +#define U300_SYSCON_CERR_CDS_CLK_EN (0x2000) +#define U300_SYSCON_CERR_ISP_CLK_EN (0x1000) +#define U300_SYSCON_CERR_MSPRO_CLK_EN (0x0800) +#define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN (0x0400) +#define U300_SYSCON_CERR_SEMI_CLK_EN (0x0200) +#define U300_SYSCON_CERR_XGAM_CLK_EN (0x0100) +#define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN (0x0080) +#define U300_SYSCON_CERR_NANDIF_CLK_EN (0x0040) +#define U300_SYSCON_CERR_EMIF_CLK_EN (0x0020) +#define U300_SYSCON_CERR_DMAC_CLK_EN (0x0010) +#define U300_SYSCON_CERR_CPU_CLK_EN (0x0008) +#define U300_SYSCON_CERR_APEX_CLK_EN (0x0004) +#define U300_SYSCON_CERR_AHB_CLK_EN (0x0002) +#define U300_SYSCON_CERR_AAIF_CLK_EN (0x0001) +/* Single block clock enable 16bit (-/W) */ +#define U300_SYSCON_SBCER (0x002c) +#define U300_SYSCON_SBCER_PPM_CLK_EN (0x0009) +#define U300_SYSCON_SBCER_ACC_TMR_CLK_EN (0x0008) +#define U300_SYSCON_SBCER_APP_TMR_CLK_EN (0x0007) +#define U300_SYSCON_SBCER_KEYPAD_CLK_EN (0x0006) +#define U300_SYSCON_SBCER_GPIO_CLK_EN (0x0004) +#define U300_SYSCON_SBCER_EH_CLK_EN (0x0003) +#define U300_SYSCON_SBCER_BTR_CLK_EN (0x0002) +#define U300_SYSCON_SBCER_UART_CLK_EN (0x0001) +#define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN (0x0000) +#define U300_SYSCON_SBCER_UART1_CLK_EN (0x0019) +#define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN (0x0018) +#define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN (0x0017) +#define U300_SYSCON_SBCER_SPI_CLK_EN (0x0016) +#define U300_SYSCON_SBCER_MMC_CLK_EN (0x0015) +#define U300_SYSCON_SBCER_I2S1_CLK_EN (0x0014) +#define U300_SYSCON_SBCER_I2S0_CLK_EN (0x0013) +#define U300_SYSCON_SBCER_I2C1_CLK_EN (0x0012) +#define U300_SYSCON_SBCER_I2C0_CLK_EN (0x0011) +#define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN (0x0010) +#define U300_SYSCON_SBCER_CDS_CLK_EN (0x002D) +#define U300_SYSCON_SBCER_ISP_CLK_EN (0x002C) +#define U300_SYSCON_SBCER_MSPRO_CLK_EN (0x002B) +#define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN (0x002A) +#define U300_SYSCON_SBCER_SEMI_CLK_EN (0x0029) +#define U300_SYSCON_SBCER_XGAM_CLK_EN (0x0028) +#define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN (0x0027) +#define U300_SYSCON_SBCER_NANDIF_CLK_EN (0x0026) +#define U300_SYSCON_SBCER_EMIF_CLK_EN (0x0025) +#define U300_SYSCON_SBCER_DMAC_CLK_EN (0x0024) +#define U300_SYSCON_SBCER_CPU_CLK_EN (0x0023) +#define U300_SYSCON_SBCER_APEX_CLK_EN (0x0022) +#define U300_SYSCON_SBCER_AHB_CLK_EN (0x0021) +#define U300_SYSCON_SBCER_AAIF_CLK_EN (0x0020) +/* Single block clock disable 16bit (-/W) */ +#define U300_SYSCON_SBCDR (0x0030) +/* Same values as above for SBCER */ +/* Clock force SLOW peripherals 16bit (R/W) */ +#define U300_SYSCON_CFSR (0x003c) +#define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN (0x0200) +#define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN (0x0100) +#define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN (0x0080) +#define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN (0x0020) +#define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN (0x0010) +#define U300_SYSCON_CFSR_EH_CLK_FORCE_EN (0x0008) +#define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN (0x0004) +#define U300_SYSCON_CFSR_UART_CLK_FORCE_EN (0x0002) +#define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN (0x0001) +/* Clock force FAST peripherals 16bit (R/W) */ +#define U300_SYSCON_CFFR (0x40) +/* Values not defined. Define if you want to use them. */ +/* Clock force the rest of the peripherals 16bit (R/W) */ +#define U300_SYSCON_CFRR (0x44) +#define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN (0x2000) +#define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN (0x1000) +#define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN (0x0800) +#define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN (0x0400) +#define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN (0x0200) +#define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN (0x0100) +#define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN (0x0080) +#define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN (0x0040) +#define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN (0x0020) +#define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN (0x0010) +#define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN (0x0008) +#define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN (0x0004) +#define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN (0x0002) +#define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN (0x0001) +/* PLL208 Frequency Control 16bit (R/W) */ +#define U300_SYSCON_PFCR (0x48) +#define U300_SYSCON_PFCR_DPLL_MULT_NUM (0x000F) +/* Power Management Control 16bit (R/W) */ +#define U300_SYSCON_PMCR (0x50) +#define U300_SYSCON_PMCR_DCON_ENABLE (0x0002) +#define U300_SYSCON_PMCR_PWR_MGNT_ENABLE (0x0001) +/* Reset Out 16bit (R/W) */ +#define U300_SYSCON_RCR (0x6c) +#define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE (0x0001) +/* EMIF Slew Rate Control 16bit (R/W) */ +#define U300_SYSCON_SRCLR (0x70) +#define U300_SYSCON_SRCLR_MASK (0x03FF) +#define U300_SYSCON_SRCLR_VALUE (0x03FF) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B (0x0200) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A (0x0100) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B (0x0080) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A (0x0040) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B (0x0020) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A (0x0010) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B (0x0008) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A (0x0004) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B (0x0002) +#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A (0x0001) +/* EMIF Clock Control Register 16bit (R/W) */ +#define U300_SYSCON_ECCR (0x0078) +#define U300_SYSCON_ECCR_MASK (0x000F) +#define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE (0x0008) +#define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004) +#define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002) +#define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001) +/* MMC/MSPRO frequency divider register 0 16bit (R/W) */ +#define U300_SYSCON_MMF0R (0x90) +#define U300_SYSCON_MMF0R_MASK (0x00FF) +#define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK (0x00F0) +#define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK (0x000F) +/* MMC/MSPRO frequency divider register 1 16bit (R/W) */ +#define U300_SYSCON_MMF1R (0x94) +#define U300_SYSCON_MMF1R_MASK (0x00FF) +#define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK (0x00F0) +#define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK (0x000F) +/* Clock control for the MMC and MSPRO blocks 16bit (R/W) */ +#define U300_SYSCON_MMCR (0x9C) +#define U300_SYSCON_MMCR_MASK (0x0003) +#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002) +#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001) +/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */ +#define U300_SYSCON_S0CCR (0x120) +#define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF) +#define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000) +#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000) +#define U300_SYSCON_S0CCR_CLOCK_INV (0x0200) +#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0) +#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E) +#define U300_SYSCON_S0CCR_CLOCK_ENABLE (0x0001) +#define U300_SYSCON_S0CCR_SEL_MCLK (0x8<<1) +#define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK (0xA<<1) +#define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK (0xC<<1) +#define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK (0xD<<1) +#define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK (0xE<<1) +#define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK (0x0<<1) +#define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK (0x2<<1) +#define U300_SYSCON_S0CCR_SEL_RTC_CLK (0x4<<1) +#define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK (0x6<<1) +/* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */ +#define U300_SYSCON_S1CCR (0x124) +#define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF) +#define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000) +#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000) +#define U300_SYSCON_S1CCR_CLOCK_INV (0x0200) +#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0) +#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E) +#define U300_SYSCON_S1CCR_CLOCK_ENABLE (0x0001) +#define U300_SYSCON_S1CCR_SEL_MCLK (0x8<<1) +#define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK (0xA<<1) +#define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK (0xC<<1) +#define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK (0xD<<1) +#define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK (0xE<<1) +#define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK (0x0<<1) +#define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK (0x2<<1) +#define U300_SYSCON_S1CCR_SEL_RTC_CLK (0x4<<1) +#define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK (0x6<<1) +/* SYS_2_CLK_CONTROL third clock contol 16 bit (R/W) */ +#define U300_SYSCON_S2CCR (0x128) +#define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF) +#define U300_SYSCON_S2CCR_CLK_STEAL (0x8000) +#define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000) +#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000) +#define U300_SYSCON_S2CCR_CLOCK_INV (0x0200) +#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0) +#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E) +#define U300_SYSCON_S2CCR_CLOCK_ENABLE (0x0001) +#define U300_SYSCON_S2CCR_SEL_MCLK (0x8<<1) +#define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK (0xA<<1) +#define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK (0xC<<1) +#define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK (0xD<<1) +#define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK (0xE<<1) +#define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK (0x0<<1) +#define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK (0x2<<1) +#define U300_SYSCON_S2CCR_SEL_RTC_CLK (0x4<<1) +#define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK (0x6<<1) +/* SC_PLL_IRQ_CONTROL 16bit (R/W) */ +#define U300_SYSCON_PICR (0x0130) +#define U300_SYSCON_PICR_MASK (0x00FF) +#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080) +#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040) +#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020) +#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010) +#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008) +#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004) +#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002) +#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001) +/* SC_PLL_IRQ_STATUS 16 bit (R/-) */ +#define U300_SYSCON_PISR (0x0134) +#define U300_SYSCON_PISR_MASK (0x000F) +#define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008) +#define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004) +#define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002) +#define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001) +/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */ +#define U300_SYSCON_PICLR (0x0138) +#define U300_SYSCON_PICLR_MASK (0x000F) +#define U300_SYSCON_PICLR_RWMASK (0x0000) +#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008) +#define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004) +#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002) +#define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001) +/* Clock activity observability register 0 */ +#define U300_SYSCON_C0OAR (0x140) +#define U300_SYSCON_C0OAR_MASK (0xFFFF) +#define U300_SYSCON_C0OAR_VALUE (0xFFFF) +#define U300_SYSCON_C0OAR_BT_H_CLK (0x8000) +#define U300_SYSCON_C0OAR_ASPB_P_CLK (0x4000) +#define U300_SYSCON_C0OAR_APP_SEMI_H_CLK (0x2000) +#define U300_SYSCON_C0OAR_APP_SEMI_CLK (0x1000) +#define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK (0x0800) +#define U300_SYSCON_C0OAR_APP_I2S1_CLK (0x0400) +#define U300_SYSCON_C0OAR_APP_I2S0_CLK (0x0200) +#define U300_SYSCON_C0OAR_APP_CPU_CLK (0x0100) +#define U300_SYSCON_C0OAR_APP_52_CLK (0x0080) +#define U300_SYSCON_C0OAR_APP_208_CLK (0x0040) +#define U300_SYSCON_C0OAR_APP_104_CLK (0x0020) +#define U300_SYSCON_C0OAR_APEX_CLK (0x0010) +#define U300_SYSCON_C0OAR_AHPB_M_H_CLK (0x0008) +#define U300_SYSCON_C0OAR_AHB_CLK (0x0004) +#define U300_SYSCON_C0OAR_AFPB_P_CLK (0x0002) +#define U300_SYSCON_C0OAR_AAIF_CLK (0x0001) +/* Clock activity observability register 1 */ +#define U300_SYSCON_C1OAR (0x144) +#define U300_SYSCON_C1OAR_MASK (0x3FFE) +#define U300_SYSCON_C1OAR_VALUE (0x3FFE) +#define U300_SYSCON_C1OAR_NFIF_F_CLK (0x2000) +#define U300_SYSCON_C1OAR_MSPRO_CLK (0x1000) +#define U300_SYSCON_C1OAR_MMC_P_CLK (0x0800) +#define U300_SYSCON_C1OAR_MMC_CLK (0x0400) +#define U300_SYSCON_C1OAR_KP_P_CLK (0x0200) +#define U300_SYSCON_C1OAR_I2C1_P_CLK (0x0100) +#define U300_SYSCON_C1OAR_I2C0_P_CLK (0x0080) +#define U300_SYSCON_C1OAR_GPIO_CLK (0x0040) +#define U300_SYSCON_C1OAR_EMIF_MPMC_CLK (0x0020) +#define U300_SYSCON_C1OAR_EMIF_H_CLK (0x0010) +#define U300_SYSCON_C1OAR_EVHIST_CLK (0x0008) +#define U300_SYSCON_C1OAR_PPM_CLK (0x0004) +#define U300_SYSCON_C1OAR_DMA_CLK (0x0002) +/* Clock activity observability register 2 */ +#define U300_SYSCON_C2OAR (0x148) +#define U300_SYSCON_C2OAR_MASK (0x0FFF) +#define U300_SYSCON_C2OAR_VALUE (0x0FFF) +#define U300_SYSCON_C2OAR_XGAM_CDI_CLK (0x0800) +#define U300_SYSCON_C2OAR_XGAM_CLK (0x0400) +#define U300_SYSCON_C2OAR_VC_H_CLK (0x0200) +#define U300_SYSCON_C2OAR_VC_CLK (0x0100) +#define U300_SYSCON_C2OAR_UA_P_CLK (0x0080) +#define U300_SYSCON_C2OAR_TMR1_CLK (0x0040) +#define U300_SYSCON_C2OAR_TMR0_CLK (0x0020) +#define U300_SYSCON_C2OAR_SPI_P_CLK (0x0010) +#define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK (0x0008) +#define U300_SYSCON_C2OAR_PCM_I2S1_CLK (0x0004) +#define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK (0x0002) +#define U300_SYSCON_C2OAR_PCM_I2S0_CLK (0x0001) + + +/* + * The clocking hierarchy currently looks like this. + * NOTE: the idea is NOT to show how the clocks are routed on the chip! + * The ideas is to show dependencies, so a clock higher up in the + * hierarchy has to be on in order for another clock to be on. Now, + * both CPU and DMA can actually be on top of the hierarchy, and that + * is not modeled currently. Instead we have the backbone AMBA bus on + * top. This bus cannot be programmed in any way but conceptually it + * needs to be active for the bridges and devices to transport data. + * + * Please be aware that a few clocks are hw controlled, which mean that + * the hw itself can turn on/off or change the rate of the clock when + * needed! + * + * AMBA bus + * | + * +- CPU + * +- FSMC NANDIF NAND Flash interface + * +- SEMI Shared Memory interface + * +- ISP Image Signal Processor (U335 only) + * +- CDS (U335 only) + * +- DMA Direct Memory Access Controller + * +- AAIF APP/ACC Inteface (Mobile Scalable Link, MSL) + * +- APEX + * +- VIDEO_ENC AVE2/3 Video Encoder + * +- XGAM Graphics Accelerator Controller + * +- AHB + * | + * +- ahb:0 AHB Bridge + * | | + * | +- ahb:1 INTCON Interrupt controller + * | +- ahb:3 MSPRO Memory Stick Pro controller + * | +- ahb:4 EMIF External Memory interface + * | + * +- fast:0 FAST bridge + * | | + * | +- fast:1 MMCSD MMC/SD card reader controller + * | +- fast:2 I2S0 PCM I2S channel 0 controller + * | +- fast:3 I2S1 PCM I2S channel 1 controller + * | +- fast:4 I2C0 I2C channel 0 controller + * | +- fast:5 I2C1 I2C channel 1 controller + * | +- fast:6 SPI SPI controller + * | +- fast:7 UART1 Secondary UART (U335 only) + * | + * +- slow:0 SLOW bridge + * | + * +- slow:1 SYSCON (not possible to control) + * +- slow:2 WDOG Watchdog + * +- slow:3 UART0 primary UART + * +- slow:4 TIMER_APP Application timer - used in Linux + * +- slow:5 KEYPAD controller + * +- slow:6 GPIO controller + * +- slow:7 RTC controller + * +- slow:8 BT Bus Tracer (not used currently) + * +- slow:9 EH Event Handler (not used currently) + * +- slow:a TIMER_ACC Access style timer (not used currently) + * +- slow:b PPM (U335 only, what is that?) + */ + +/* Global syscon virtual base */ +static void __iomem *syscon_vbase; + +/** + * struct clk_syscon - U300 syscon clock + * @hw: corresponding clock hardware entry + * @hw_ctrld: whether this clock is hardware controlled (for refcount etc) + * and does not need any magic pokes to be enabled/disabled + * @reset: state holder, whether this block's reset line is asserted or not + * @res_reg: reset line enable/disable flag register + * @res_bit: bit for resetting or taking this consumer out of reset + * @en_reg: clock line enable/disable flag register + * @en_bit: bit for enabling/disabling this consumer clock line + * @clk_val: magic value to poke in the register to enable/disable + * this one clock + */ +struct clk_syscon { + struct clk_hw hw; + bool hw_ctrld; + bool reset; + void __iomem *res_reg; + u8 res_bit; + void __iomem *en_reg; + u8 en_bit; + u16 clk_val; +}; + +#define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw) + +static DEFINE_SPINLOCK(syscon_resetreg_lock); + +/* + * Reset control functions. We remember if a block has been + * taken out of reset and don't remove the reset assertion again + * and vice versa. Currently we only remove resets so the + * enablement function is defined out. + */ +static void syscon_block_reset_enable(struct clk_syscon *sclk) +{ + unsigned long iflags; + u16 val; + + /* Not all blocks support resetting */ + if (!sclk->res_reg) + return; + spin_lock_irqsave(&syscon_resetreg_lock, iflags); + val = readw(sclk->res_reg); + val |= BIT(sclk->res_bit); + writew(val, sclk->res_reg); + spin_unlock_irqrestore(&syscon_resetreg_lock, iflags); + sclk->reset = true; +} + +static void syscon_block_reset_disable(struct clk_syscon *sclk) +{ + unsigned long iflags; + u16 val; + + /* Not all blocks support resetting */ + if (!sclk->res_reg) + return; + spin_lock_irqsave(&syscon_resetreg_lock, iflags); + val = readw(sclk->res_reg); + val &= ~BIT(sclk->res_bit); + writew(val, sclk->res_reg); + spin_unlock_irqrestore(&syscon_resetreg_lock, iflags); + sclk->reset = false; +} + +static int syscon_clk_prepare(struct clk_hw *hw) +{ + struct clk_syscon *sclk = to_syscon(hw); + + /* If the block is in reset, bring it out */ + if (sclk->reset) + syscon_block_reset_disable(sclk); + return 0; +} + +static void syscon_clk_unprepare(struct clk_hw *hw) +{ + struct clk_syscon *sclk = to_syscon(hw); + + /* Please don't force the console into reset */ + if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN) + return; + /* When unpreparing, force block into reset */ + if (!sclk->reset) + syscon_block_reset_enable(sclk); +} + +static int syscon_clk_enable(struct clk_hw *hw) +{ + struct clk_syscon *sclk = to_syscon(hw); + + /* Don't touch the hardware controlled clocks */ + if (sclk->hw_ctrld) + return 0; + /* These cannot be controlled */ + if (sclk->clk_val == 0xFFFFU) + return 0; + + writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER); + return 0; +} + +static void syscon_clk_disable(struct clk_hw *hw) +{ + struct clk_syscon *sclk = to_syscon(hw); + + /* Don't touch the hardware controlled clocks */ + if (sclk->hw_ctrld) + return; + if (sclk->clk_val == 0xFFFFU) + return; + /* Please don't disable the console port */ + if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN) + return; + + writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR); +} + +static int syscon_clk_is_enabled(struct clk_hw *hw) +{ + struct clk_syscon *sclk = to_syscon(hw); + u16 val; + + /* If no enable register defined, it's always-on */ + if (!sclk->en_reg) + return 1; + + val = readw(sclk->en_reg); + val &= BIT(sclk->en_bit); + + return val ? 1 : 0; +} + +static u16 syscon_get_perf(void) +{ + u16 val; + + val = readw(syscon_vbase + U300_SYSCON_CCR); + val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK; + return val; +} + +static unsigned long +syscon_clk_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct clk_syscon *sclk = to_syscon(hw); + u16 perf = syscon_get_perf(); + + switch(sclk->clk_val) { + case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN: + case U300_SYSCON_SBCER_I2C0_CLK_EN: + case U300_SYSCON_SBCER_I2C1_CLK_EN: + case U300_SYSCON_SBCER_MMC_CLK_EN: + case U300_SYSCON_SBCER_SPI_CLK_EN: + /* The FAST clocks have one progression */ + switch(perf) { + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: + return 13000000; + default: + return parent_rate; /* 26 MHz */ + } + case U300_SYSCON_SBCER_DMAC_CLK_EN: + case U300_SYSCON_SBCER_NANDIF_CLK_EN: + case U300_SYSCON_SBCER_XGAM_CLK_EN: + /* AMBA interconnect peripherals */ + switch(perf) { + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: + return 6500000; + case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: + return 26000000; + default: + return parent_rate; /* 52 MHz */ + } + case U300_SYSCON_SBCER_SEMI_CLK_EN: + case U300_SYSCON_SBCER_EMIF_CLK_EN: + /* EMIF speeds */ + switch(perf) { + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: + return 13000000; + case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: + return 52000000; + default: + return 104000000; + } + case U300_SYSCON_SBCER_CPU_CLK_EN: + /* And the fast CPU clock */ + switch(perf) { + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: + return 13000000; + case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: + return 52000000; + case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH: + return 104000000; + default: + return parent_rate; /* 208 MHz */ + } + default: + /* + * The SLOW clocks and default just inherit the rate of + * their parent (typically PLL13 13 MHz). + */ + return parent_rate; + } +} + +static long +syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate, + unsigned long *prate) +{ + struct clk_syscon *sclk = to_syscon(hw); + + if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN) + return *prate; + /* We really only support setting the rate of the CPU clock */ + if (rate <= 13000000) + return 13000000; + if (rate <= 52000000) + return 52000000; + if (rate <= 104000000) + return 104000000; + return 208000000; +} + +static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + struct clk_syscon *sclk = to_syscon(hw); + u16 val; + + /* We only support setting the rate of the CPU clock */ + if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN) + return -EINVAL; + switch (rate) { + case 13000000: + val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER; + break; + case 52000000: + val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE; + break; + case 104000000: + val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH; + break; + case 208000000: + val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST; + break; + default: + return -EINVAL; + } + val |= readw(syscon_vbase + U300_SYSCON_CCR) & + ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ; + writew(val, syscon_vbase + U300_SYSCON_CCR); + return 0; +} + +static const struct clk_ops syscon_clk_ops = { + .prepare = syscon_clk_prepare, + .unprepare = syscon_clk_unprepare, + .enable = syscon_clk_enable, + .disable = syscon_clk_disable, + .is_enabled = syscon_clk_is_enabled, + .recalc_rate = syscon_clk_recalc_rate, + .round_rate = syscon_clk_round_rate, + .set_rate = syscon_clk_set_rate, +}; + +static struct clk * __init +syscon_clk_register(struct device *dev, const char *name, + const char *parent_name, unsigned long flags, + bool hw_ctrld, + void __iomem *res_reg, u8 res_bit, + void __iomem *en_reg, u8 en_bit, + u16 clk_val) +{ + struct clk *clk; + struct clk_syscon *sclk; + struct clk_init_data init; + + sclk = kzalloc(sizeof(struct clk_syscon), GFP_KERNEL); + if (!sclk) { + pr_err("could not allocate syscon clock %s\n", + name); + return ERR_PTR(-ENOMEM); + } + init.name = name; + init.ops = &syscon_clk_ops; + init.flags = flags; + init.parent_names = (parent_name ? &parent_name : NULL); + init.num_parents = (parent_name ? 1 : 0); + sclk->hw.init = &init; + sclk->hw_ctrld = hw_ctrld; + /* Assume the block is in reset at registration */ + sclk->reset = true; + sclk->res_reg = res_reg; + sclk->res_bit = res_bit; + sclk->en_reg = en_reg; + sclk->en_bit = en_bit; + sclk->clk_val = clk_val; + + clk = clk_register(dev, &sclk->hw); + if (IS_ERR(clk)) + kfree(sclk); + + return clk; +} + +#define U300_CLK_TYPE_SLOW 0 +#define U300_CLK_TYPE_FAST 1 +#define U300_CLK_TYPE_REST 2 + +/** + * struct u300_clock - defines the bits and pieces for a certain clock + * @type: the clock type, slow fast or rest + * @id: the bit in the slow/fast/rest register for this clock + * @hw_ctrld: whether the clock is hardware controlled + * @clk_val: a value to poke in the one-write enable/disable registers + */ +struct u300_clock { + u8 type; + u8 id; + bool hw_ctrld; + u16 clk_val; +}; + +static struct u300_clock const u300_clk_lookup[] __initconst = { + { + .type = U300_CLK_TYPE_REST, + .id = 3, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_CPU_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 4, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 5, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 6, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 8, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 9, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 10, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN, + }, + { + .type = U300_CLK_TYPE_REST, + .id = 12, + .hw_ctrld = false, + /* INTCON: cannot be enabled, just taken out of reset */ + .clk_val = 0xFFFFU, + }, + { + .type = U300_CLK_TYPE_FAST, + .id = 0, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN, + }, + { + .type = U300_CLK_TYPE_FAST, + .id = 1, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN, + }, + { + .type = U300_CLK_TYPE_FAST, + .id = 2, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN, + }, + { + .type = U300_CLK_TYPE_FAST, + .id = 5, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_MMC_CLK_EN, + }, + { + .type = U300_CLK_TYPE_FAST, + .id = 6, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_SPI_CLK_EN, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 0, + .hw_ctrld = true, + .clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 1, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_UART_CLK_EN, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 4, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 6, + .hw_ctrld = true, + /* No clock enable register bit */ + .clk_val = 0xFFFFU, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 7, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN, + }, + { + .type = U300_CLK_TYPE_SLOW, + .id = 8, + .hw_ctrld = false, + .clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN, + }, +}; + +static void __init of_u300_syscon_clk_init(struct device_node *np) +{ + struct clk *clk = ERR_PTR(-EINVAL); + const char *clk_name = np->name; + const char *parent_name; + void __iomem *res_reg; + void __iomem *en_reg; + u32 clk_type; + u32 clk_id; + int i; + + if (of_property_read_u32(np, "clock-type", &clk_type)) { + pr_err("%s: syscon clock \"%s\" missing clock-type property\n", + __func__, clk_name); + return; + } + if (of_property_read_u32(np, "clock-id", &clk_id)) { + pr_err("%s: syscon clock \"%s\" missing clock-id property\n", + __func__, clk_name); + return; + } + parent_name = of_clk_get_parent_name(np, 0); + + switch (clk_type) { + case U300_CLK_TYPE_SLOW: + res_reg = syscon_vbase + U300_SYSCON_RSR; + en_reg = syscon_vbase + U300_SYSCON_CESR; + break; + case U300_CLK_TYPE_FAST: + res_reg = syscon_vbase + U300_SYSCON_RFR; + en_reg = syscon_vbase + U300_SYSCON_CEFR; + break; + case U300_CLK_TYPE_REST: + res_reg = syscon_vbase + U300_SYSCON_RRR; + en_reg = syscon_vbase + U300_SYSCON_CERR; + break; + default: + pr_err("unknown clock type %x specified\n", clk_type); + return; + } + + for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) { + const struct u300_clock *u3clk = &u300_clk_lookup[i]; + + if (u3clk->type == clk_type && u3clk->id == clk_id) + clk = syscon_clk_register(NULL, + clk_name, parent_name, + 0, u3clk->hw_ctrld, + res_reg, u3clk->id, + en_reg, u3clk->id, + u3clk->clk_val); + } + + if (!IS_ERR(clk)) { + of_clk_add_provider(np, of_clk_src_simple_get, clk); + + /* + * Some few system clocks - device tree does not + * represent clocks without a corresponding device node. + * for now we add these three clocks here. + */ + if (clk_type == U300_CLK_TYPE_REST && clk_id == 5) + clk_register_clkdev(clk, NULL, "pl172"); + if (clk_type == U300_CLK_TYPE_REST && clk_id == 9) + clk_register_clkdev(clk, NULL, "semi"); + if (clk_type == U300_CLK_TYPE_REST && clk_id == 12) + clk_register_clkdev(clk, NULL, "intcon"); + } +} + +/** + * struct clk_mclk - U300 MCLK clock (MMC/SD clock) + * @hw: corresponding clock hardware entry + * @is_mspro: if this is the memory stick clock rather than MMC/SD + */ +struct clk_mclk { + struct clk_hw hw; + bool is_mspro; +}; + +#define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw) + +static int mclk_clk_prepare(struct clk_hw *hw) +{ + struct clk_mclk *mclk = to_mclk(hw); + u16 val; + + /* The MMC and MSPRO clocks need some special set-up */ + if (!mclk->is_mspro) { + /* Set default MMC clock divisor to 18.9 MHz */ + writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R); + val = readw(syscon_vbase + U300_SYSCON_MMCR); + /* Disable the MMC feedback clock */ + val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE; + /* Disable MSPRO frequency */ + val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE; + writew(val, syscon_vbase + U300_SYSCON_MMCR); + } else { + val = readw(syscon_vbase + U300_SYSCON_MMCR); + /* Disable the MMC feedback clock */ + val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE; + /* Enable MSPRO frequency */ + val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE; + writew(val, syscon_vbase + U300_SYSCON_MMCR); + } + + return 0; +} + +static unsigned long +mclk_clk_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + u16 perf = syscon_get_perf(); + + switch (perf) { + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: + /* + * Here, the 208 MHz PLL gets shut down and the always + * on 13 MHz PLL used for RTC etc kicks into use + * instead. + */ + return 13000000; + case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH: + case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST: + { + /* + * This clock is under program control. The register is + * divided in two nybbles, bit 7-4 gives cycles-1 to count + * high, bit 3-0 gives cycles-1 to count low. Distribute + * these with no more than 1 cycle difference between + * low and high and add low and high to get the actual + * divisor. The base PLL is 208 MHz. Writing 0x00 will + * divide by 1 and 1 so the highest frequency possible + * is 104 MHz. + * + * e.g. 0x54 => + * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz + */ + u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) & + U300_SYSCON_MMF0R_MASK; + switch (val) { + case 0x0054: + return 18900000; + case 0x0044: + return 20800000; + case 0x0043: + return 23100000; + case 0x0033: + return 26000000; + case 0x0032: + return 29700000; + case 0x0022: + return 34700000; + case 0x0021: + return 41600000; + case 0x0011: + return 52000000; + case 0x0000: + return 104000000; + default: + break; + } + } + default: + break; + } + return parent_rate; +} + +static long +mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate, + unsigned long *prate) +{ + if (rate <= 18900000) + return 18900000; + if (rate <= 20800000) + return 20800000; + if (rate <= 23100000) + return 23100000; + if (rate <= 26000000) + return 26000000; + if (rate <= 29700000) + return 29700000; + if (rate <= 34700000) + return 34700000; + if (rate <= 41600000) + return 41600000; + /* Highest rate */ + return 52000000; +} + +static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + u16 val; + u16 reg; + + switch (rate) { + case 18900000: + val = 0x0054; + break; + case 20800000: + val = 0x0044; + break; + case 23100000: + val = 0x0043; + break; + case 26000000: + val = 0x0033; + break; + case 29700000: + val = 0x0032; + break; + case 34700000: + val = 0x0022; + break; + case 41600000: + val = 0x0021; + break; + case 52000000: + val = 0x0011; + break; + case 104000000: + val = 0x0000; + break; + default: + return -EINVAL; + } + + reg = readw(syscon_vbase + U300_SYSCON_MMF0R) & + ~U300_SYSCON_MMF0R_MASK; + writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R); + return 0; +} + +static const struct clk_ops mclk_ops = { + .prepare = mclk_clk_prepare, + .recalc_rate = mclk_clk_recalc_rate, + .round_rate = mclk_clk_round_rate, + .set_rate = mclk_clk_set_rate, +}; + +static struct clk * __init +mclk_clk_register(struct device *dev, const char *name, + const char *parent_name, bool is_mspro) +{ + struct clk *clk; + struct clk_mclk *mclk; + struct clk_init_data init; + + mclk = kzalloc(sizeof(struct clk_mclk), GFP_KERNEL); + if (!mclk) { + pr_err("could not allocate MMC/SD clock %s\n", + name); + return ERR_PTR(-ENOMEM); + } + init.name = "mclk"; + init.ops = &mclk_ops; + init.flags = 0; + init.parent_names = (parent_name ? &parent_name : NULL); + init.num_parents = (parent_name ? 1 : 0); + mclk->hw.init = &init; + mclk->is_mspro = is_mspro; + + clk = clk_register(dev, &mclk->hw); + if (IS_ERR(clk)) + kfree(mclk); + + return clk; +} + +static void __init of_u300_syscon_mclk_init(struct device_node *np) +{ + struct clk *clk = ERR_PTR(-EINVAL); + const char *clk_name = np->name; + const char *parent_name; + + parent_name = of_clk_get_parent_name(np, 0); + clk = mclk_clk_register(NULL, clk_name, parent_name, false); + if (!IS_ERR(clk)) + of_clk_add_provider(np, of_clk_src_simple_get, clk); +} + +static const struct of_device_id u300_clk_match[] __initconst = { + { + .compatible = "fixed-clock", + .data = of_fixed_clk_setup, + }, + { + .compatible = "fixed-factor-clock", + .data = of_fixed_factor_clk_setup, + }, + { + .compatible = "stericsson,u300-syscon-clk", + .data = of_u300_syscon_clk_init, + }, + { + .compatible = "stericsson,u300-syscon-mclk", + .data = of_u300_syscon_mclk_init, + }, + {} +}; + + +void __init u300_clk_init(void __iomem *base) +{ + u16 val; + + syscon_vbase = base; + + /* Set system to run at PLL208, max performance, a known state. */ + val = readw(syscon_vbase + U300_SYSCON_CCR); + val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK; + writew(val, syscon_vbase + U300_SYSCON_CCR); + /* Wait for the PLL208 to lock if not locked in yet */ + while (!(readw(syscon_vbase + U300_SYSCON_CSR) & + U300_SYSCON_CSR_PLL208_LOCK_IND)); + + /* Power management enable */ + val = readw(syscon_vbase + U300_SYSCON_PMCR); + val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE; + writew(val, syscon_vbase + U300_SYSCON_PMCR); + + of_clk_init(u300_clk_match); +} |