summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/au1xmmc.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host/au1xmmc.c')
-rw-r--r--drivers/mmc/host/au1xmmc.c1240
1 files changed, 1240 insertions, 0 deletions
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
new file mode 100644
index 000000000..ed77fbfa4
--- /dev/null
+++ b/drivers/mmc/host/au1xmmc.c
@@ -0,0 +1,1240 @@
+/*
+ * linux/drivers/mmc/host/au1xmmc.c - AU1XX0 MMC driver
+ *
+ * Copyright (c) 2005, Advanced Micro Devices, Inc.
+ *
+ * Developed with help from the 2.4.30 MMC AU1XXX controller including
+ * the following copyright notices:
+ * Copyright (c) 2003-2004 Embedded Edge, LLC.
+ * Portions Copyright (C) 2002 Embedix, Inc
+ * Copyright 2002 Hewlett-Packard Company
+
+ * 2.6 version of this driver inspired by:
+ * (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
+ * All Rights Reserved.
+ * (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
+ * All Rights Reserved.
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* Why don't we use the SD controllers' carddetect feature?
+ *
+ * From the AU1100 MMC application guide:
+ * If the Au1100-based design is intended to support both MultiMediaCards
+ * and 1- or 4-data bit SecureDigital cards, then the solution is to
+ * connect a weak (560KOhm) pull-up resistor to connector pin 1.
+ * In doing so, a MMC card never enters SPI-mode communications,
+ * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
+ * (the low to high transition will not occur).
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/slab.h>
+
+#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+
+#define DRIVER_NAME "au1xxx-mmc"
+
+/* Set this to enable special debugging macros */
+/* #define DEBUG */
+
+#ifdef DEBUG
+#define DBG(fmt, idx, args...) \
+ pr_debug("au1xmmc(%d): DEBUG: " fmt, idx, ##args)
+#else
+#define DBG(fmt, idx, args...) do {} while (0)
+#endif
+
+/* Hardware definitions */
+#define AU1XMMC_DESCRIPTOR_COUNT 1
+
+/* max DMA seg size: 64KB on Au1100, 4MB on Au1200 */
+#define AU1100_MMC_DESCRIPTOR_SIZE 0x0000ffff
+#define AU1200_MMC_DESCRIPTOR_SIZE 0x003fffff
+
+#define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \
+ MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \
+ MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36)
+
+/* This gives us a hard value for the stop command that we can write directly
+ * to the command register.
+ */
+#define STOP_CMD \
+ (SD_CMD_RT_1B | SD_CMD_CT_7 | (0xC << SD_CMD_CI_SHIFT) | SD_CMD_GO)
+
+/* This is the set of interrupts that we configure by default. */
+#define AU1XMMC_INTERRUPTS \
+ (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_RAT | \
+ SD_CONFIG_CR | SD_CONFIG_I)
+
+/* The poll event (looking for insert/remove events runs twice a second. */
+#define AU1XMMC_DETECT_TIMEOUT (HZ/2)
+
+struct au1xmmc_host {
+ struct mmc_host *mmc;
+ struct mmc_request *mrq;
+
+ u32 flags;
+ void __iomem *iobase;
+ u32 clock;
+ u32 bus_width;
+ u32 power_mode;
+
+ int status;
+
+ struct {
+ int len;
+ int dir;
+ } dma;
+
+ struct {
+ int index;
+ int offset;
+ int len;
+ } pio;
+
+ u32 tx_chan;
+ u32 rx_chan;
+
+ int irq;
+
+ struct tasklet_struct finish_task;
+ struct tasklet_struct data_task;
+ struct au1xmmc_platform_data *platdata;
+ struct platform_device *pdev;
+ struct resource *ioarea;
+ struct clk *clk;
+};
+
+/* Status flags used by the host structure */
+#define HOST_F_XMIT 0x0001
+#define HOST_F_RECV 0x0002
+#define HOST_F_DMA 0x0010
+#define HOST_F_DBDMA 0x0020
+#define HOST_F_ACTIVE 0x0100
+#define HOST_F_STOP 0x1000
+
+#define HOST_S_IDLE 0x0001
+#define HOST_S_CMD 0x0002
+#define HOST_S_DATA 0x0003
+#define HOST_S_STOP 0x0004
+
+/* Easy access macros */
+#define HOST_STATUS(h) ((h)->iobase + SD_STATUS)
+#define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG)
+#define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE)
+#define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT)
+#define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT)
+#define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG)
+#define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE)
+#define HOST_CMD(h) ((h)->iobase + SD_CMD)
+#define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2)
+#define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT)
+#define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG)
+
+#define DMA_CHANNEL(h) \
+ (((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan)
+
+static inline int has_dbdma(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1200:
+ case ALCHEMY_CPU_AU1300:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
+{
+ u32 val = __raw_readl(HOST_CONFIG(host));
+ val |= mask;
+ __raw_writel(val, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
+}
+
+static inline void FLUSH_FIFO(struct au1xmmc_host *host)
+{
+ u32 val = __raw_readl(HOST_CONFIG2(host));
+
+ __raw_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
+
+ /* SEND_STOP will turn off clock control - this re-enables it */
+ val &= ~SD_CONFIG2_DF;
+
+ __raw_writel(val, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+}
+
+static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
+{
+ u32 val = __raw_readl(HOST_CONFIG(host));
+ val &= ~mask;
+ __raw_writel(val, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
+}
+
+static inline void SEND_STOP(struct au1xmmc_host *host)
+{
+ u32 config2;
+
+ WARN_ON(host->status != HOST_S_DATA);
+ host->status = HOST_S_STOP;
+
+ config2 = __raw_readl(HOST_CONFIG2(host));
+ __raw_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+
+ /* Send the stop command */
+ __raw_writel(STOP_CMD, HOST_CMD(host));
+ wmb(); /* drain writebuffer */
+}
+
+static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
+{
+ if (host->platdata && host->platdata->set_power)
+ host->platdata->set_power(host->mmc, state);
+}
+
+static int au1xmmc_card_inserted(struct mmc_host *mmc)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+
+ if (host->platdata && host->platdata->card_inserted)
+ return !!host->platdata->card_inserted(host->mmc);
+
+ return -ENOSYS;
+}
+
+static int au1xmmc_card_readonly(struct mmc_host *mmc)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+
+ if (host->platdata && host->platdata->card_readonly)
+ return !!host->platdata->card_readonly(mmc);
+
+ return -ENOSYS;
+}
+
+static void au1xmmc_finish_request(struct au1xmmc_host *host)
+{
+ struct mmc_request *mrq = host->mrq;
+
+ host->mrq = NULL;
+ host->flags &= HOST_F_ACTIVE | HOST_F_DMA;
+
+ host->dma.len = 0;
+ host->dma.dir = 0;
+
+ host->pio.index = 0;
+ host->pio.offset = 0;
+ host->pio.len = 0;
+
+ host->status = HOST_S_IDLE;
+
+ mmc_request_done(host->mmc, mrq);
+}
+
+static void au1xmmc_tasklet_finish(unsigned long param)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *) param;
+ au1xmmc_finish_request(host);
+}
+
+static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
+ struct mmc_command *cmd, struct mmc_data *data)
+{
+ u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
+
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_NONE:
+ break;
+ case MMC_RSP_R1:
+ mmccmd |= SD_CMD_RT_1;
+ break;
+ case MMC_RSP_R1B:
+ mmccmd |= SD_CMD_RT_1B;
+ break;
+ case MMC_RSP_R2:
+ mmccmd |= SD_CMD_RT_2;
+ break;
+ case MMC_RSP_R3:
+ mmccmd |= SD_CMD_RT_3;
+ break;
+ default:
+ pr_info("au1xmmc: unhandled response type %02x\n",
+ mmc_resp_type(cmd));
+ return -EINVAL;
+ }
+
+ if (data) {
+ if (data->flags & MMC_DATA_READ) {
+ if (data->blocks > 1)
+ mmccmd |= SD_CMD_CT_4;
+ else
+ mmccmd |= SD_CMD_CT_2;
+ } else if (data->flags & MMC_DATA_WRITE) {
+ if (data->blocks > 1)
+ mmccmd |= SD_CMD_CT_3;
+ else
+ mmccmd |= SD_CMD_CT_1;
+ }
+ }
+
+ __raw_writel(cmd->arg, HOST_CMDARG(host));
+ wmb(); /* drain writebuffer */
+
+ if (wait)
+ IRQ_OFF(host, SD_CONFIG_CR);
+
+ __raw_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
+ wmb(); /* drain writebuffer */
+
+ /* Wait for the command to go on the line */
+ while (__raw_readl(HOST_CMD(host)) & SD_CMD_GO)
+ /* nop */;
+
+ /* Wait for the command to come back */
+ if (wait) {
+ u32 status = __raw_readl(HOST_STATUS(host));
+
+ while (!(status & SD_STATUS_CR))
+ status = __raw_readl(HOST_STATUS(host));
+
+ /* Clear the CR status */
+ __raw_writel(SD_STATUS_CR, HOST_STATUS(host));
+
+ IRQ_ON(host, SD_CONFIG_CR);
+ }
+
+ return 0;
+}
+
+static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
+{
+ struct mmc_request *mrq = host->mrq;
+ struct mmc_data *data;
+ u32 crc;
+
+ WARN_ON((host->status != HOST_S_DATA) && (host->status != HOST_S_STOP));
+
+ if (host->mrq == NULL)
+ return;
+
+ data = mrq->cmd->data;
+
+ if (status == 0)
+ status = __raw_readl(HOST_STATUS(host));
+
+ /* The transaction is really over when the SD_STATUS_DB bit is clear */
+ while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
+ status = __raw_readl(HOST_STATUS(host));
+
+ data->error = 0;
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
+
+ /* Process any errors */
+ crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
+ if (host->flags & HOST_F_XMIT)
+ crc |= ((status & 0x07) == 0x02) ? 0 : 1;
+
+ if (crc)
+ data->error = -EILSEQ;
+
+ /* Clear the CRC bits */
+ __raw_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
+
+ data->bytes_xfered = 0;
+
+ if (!data->error) {
+ if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) {
+ u32 chan = DMA_CHANNEL(host);
+
+ chan_tab_t *c = *((chan_tab_t **)chan);
+ au1x_dma_chan_t *cp = c->chan_ptr;
+ data->bytes_xfered = cp->ddma_bytecnt;
+ } else
+ data->bytes_xfered =
+ (data->blocks * data->blksz) - host->pio.len;
+ }
+
+ au1xmmc_finish_request(host);
+}
+
+static void au1xmmc_tasklet_data(unsigned long param)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *)param;
+
+ u32 status = __raw_readl(HOST_STATUS(host));
+ au1xmmc_data_complete(host, status);
+}
+
+#define AU1XMMC_MAX_TRANSFER 8
+
+static void au1xmmc_send_pio(struct au1xmmc_host *host)
+{
+ struct mmc_data *data;
+ int sg_len, max, count;
+ unsigned char *sg_ptr, val;
+ u32 status;
+ struct scatterlist *sg;
+
+ data = host->mrq->data;
+
+ if (!(host->flags & HOST_F_XMIT))
+ return;
+
+ /* This is the pointer to the data buffer */
+ sg = &data->sg[host->pio.index];
+ sg_ptr = sg_virt(sg) + host->pio.offset;
+
+ /* This is the space left inside the buffer */
+ sg_len = data->sg[host->pio.index].length - host->pio.offset;
+
+ /* Check if we need less than the size of the sg_buffer */
+ max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
+ if (max > AU1XMMC_MAX_TRANSFER)
+ max = AU1XMMC_MAX_TRANSFER;
+
+ for (count = 0; count < max; count++) {
+ status = __raw_readl(HOST_STATUS(host));
+
+ if (!(status & SD_STATUS_TH))
+ break;
+
+ val = *sg_ptr++;
+
+ __raw_writel((unsigned long)val, HOST_TXPORT(host));
+ wmb(); /* drain writebuffer */
+ }
+
+ host->pio.len -= count;
+ host->pio.offset += count;
+
+ if (count == sg_len) {
+ host->pio.index++;
+ host->pio.offset = 0;
+ }
+
+ if (host->pio.len == 0) {
+ IRQ_OFF(host, SD_CONFIG_TH);
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+ }
+}
+
+static void au1xmmc_receive_pio(struct au1xmmc_host *host)
+{
+ struct mmc_data *data;
+ int max, count, sg_len = 0;
+ unsigned char *sg_ptr = NULL;
+ u32 status, val;
+ struct scatterlist *sg;
+
+ data = host->mrq->data;
+
+ if (!(host->flags & HOST_F_RECV))
+ return;
+
+ max = host->pio.len;
+
+ if (host->pio.index < host->dma.len) {
+ sg = &data->sg[host->pio.index];
+ sg_ptr = sg_virt(sg) + host->pio.offset;
+
+ /* This is the space left inside the buffer */
+ sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
+
+ /* Check if we need less than the size of the sg_buffer */
+ if (sg_len < max)
+ max = sg_len;
+ }
+
+ if (max > AU1XMMC_MAX_TRANSFER)
+ max = AU1XMMC_MAX_TRANSFER;
+
+ for (count = 0; count < max; count++) {
+ status = __raw_readl(HOST_STATUS(host));
+
+ if (!(status & SD_STATUS_NE))
+ break;
+
+ if (status & SD_STATUS_RC) {
+ DBG("RX CRC Error [%d + %d].\n", host->pdev->id,
+ host->pio.len, count);
+ break;
+ }
+
+ if (status & SD_STATUS_RO) {
+ DBG("RX Overrun [%d + %d]\n", host->pdev->id,
+ host->pio.len, count);
+ break;
+ }
+ else if (status & SD_STATUS_RU) {
+ DBG("RX Underrun [%d + %d]\n", host->pdev->id,
+ host->pio.len, count);
+ break;
+ }
+
+ val = __raw_readl(HOST_RXPORT(host));
+
+ if (sg_ptr)
+ *sg_ptr++ = (unsigned char)(val & 0xFF);
+ }
+
+ host->pio.len -= count;
+ host->pio.offset += count;
+
+ if (sg_len && count == sg_len) {
+ host->pio.index++;
+ host->pio.offset = 0;
+ }
+
+ if (host->pio.len == 0) {
+ /* IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); */
+ IRQ_OFF(host, SD_CONFIG_NE);
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+ }
+}
+
+/* This is called when a command has been completed - grab the response
+ * and check for errors. Then start the data transfer if it is indicated.
+ */
+static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
+{
+ struct mmc_request *mrq = host->mrq;
+ struct mmc_command *cmd;
+ u32 r[4];
+ int i, trans;
+
+ if (!host->mrq)
+ return;
+
+ cmd = mrq->cmd;
+ cmd->error = 0;
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ r[0] = __raw_readl(host->iobase + SD_RESP3);
+ r[1] = __raw_readl(host->iobase + SD_RESP2);
+ r[2] = __raw_readl(host->iobase + SD_RESP1);
+ r[3] = __raw_readl(host->iobase + SD_RESP0);
+
+ /* The CRC is omitted from the response, so really
+ * we only got 120 bytes, but the engine expects
+ * 128 bits, so we have to shift things up.
+ */
+ for (i = 0; i < 4; i++) {
+ cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
+ if (i != 3)
+ cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
+ }
+ } else {
+ /* Techincally, we should be getting all 48 bits of
+ * the response (SD_RESP1 + SD_RESP2), but because
+ * our response omits the CRC, our data ends up
+ * being shifted 8 bits to the right. In this case,
+ * that means that the OSR data starts at bit 31,
+ * so we can just read RESP0 and return that.
+ */
+ cmd->resp[0] = __raw_readl(host->iobase + SD_RESP0);
+ }
+ }
+
+ /* Figure out errors */
+ if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
+ cmd->error = -EILSEQ;
+
+ trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
+
+ if (!trans || cmd->error) {
+ IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF);
+ tasklet_schedule(&host->finish_task);
+ return;
+ }
+
+ host->status = HOST_S_DATA;
+
+ if ((host->flags & (HOST_F_DMA | HOST_F_DBDMA))) {
+ u32 channel = DMA_CHANNEL(host);
+
+ /* Start the DBDMA as soon as the buffer gets something in it */
+
+ if (host->flags & HOST_F_RECV) {
+ u32 mask = SD_STATUS_DB | SD_STATUS_NE;
+
+ while((status & mask) != mask)
+ status = __raw_readl(HOST_STATUS(host));
+ }
+
+ au1xxx_dbdma_start(channel);
+ }
+}
+
+static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
+{
+ unsigned int pbus = clk_get_rate(host->clk);
+ unsigned int divisor = ((pbus / rate) / 2) - 1;
+ u32 config;
+
+ config = __raw_readl(HOST_CONFIG(host));
+
+ config &= ~(SD_CONFIG_DIV);
+ config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
+
+ __raw_writel(config, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
+}
+
+static int au1xmmc_prepare_data(struct au1xmmc_host *host,
+ struct mmc_data *data)
+{
+ int datalen = data->blocks * data->blksz;
+
+ if (data->flags & MMC_DATA_READ)
+ host->flags |= HOST_F_RECV;
+ else
+ host->flags |= HOST_F_XMIT;
+
+ if (host->mrq->stop)
+ host->flags |= HOST_F_STOP;
+
+ host->dma.dir = DMA_BIDIRECTIONAL;
+
+ host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
+ data->sg_len, host->dma.dir);
+
+ if (host->dma.len == 0)
+ return -ETIMEDOUT;
+
+ __raw_writel(data->blksz - 1, HOST_BLKSIZE(host));
+
+ if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) {
+ int i;
+ u32 channel = DMA_CHANNEL(host);
+
+ au1xxx_dbdma_stop(channel);
+
+ for (i = 0; i < host->dma.len; i++) {
+ u32 ret = 0, flags = DDMA_FLAGS_NOIE;
+ struct scatterlist *sg = &data->sg[i];
+ int sg_len = sg->length;
+
+ int len = (datalen > sg_len) ? sg_len : datalen;
+
+ if (i == host->dma.len - 1)
+ flags = DDMA_FLAGS_IE;
+
+ if (host->flags & HOST_F_XMIT) {
+ ret = au1xxx_dbdma_put_source(channel,
+ sg_phys(sg), len, flags);
+ } else {
+ ret = au1xxx_dbdma_put_dest(channel,
+ sg_phys(sg), len, flags);
+ }
+
+ if (!ret)
+ goto dataerr;
+
+ datalen -= len;
+ }
+ } else {
+ host->pio.index = 0;
+ host->pio.offset = 0;
+ host->pio.len = datalen;
+
+ if (host->flags & HOST_F_XMIT)
+ IRQ_ON(host, SD_CONFIG_TH);
+ else
+ IRQ_ON(host, SD_CONFIG_NE);
+ /* IRQ_ON(host, SD_CONFIG_RA | SD_CONFIG_RF); */
+ }
+
+ return 0;
+
+dataerr:
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ host->dma.dir);
+ return -ETIMEDOUT;
+}
+
+/* This actually starts a command or data transaction */
+static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+ int ret = 0;
+
+ WARN_ON(irqs_disabled());
+ WARN_ON(host->status != HOST_S_IDLE);
+
+ host->mrq = mrq;
+ host->status = HOST_S_CMD;
+
+ /* fail request immediately if no card is present */
+ if (0 == au1xmmc_card_inserted(mmc)) {
+ mrq->cmd->error = -ENOMEDIUM;
+ au1xmmc_finish_request(host);
+ return;
+ }
+
+ if (mrq->data) {
+ FLUSH_FIFO(host);
+ ret = au1xmmc_prepare_data(host, mrq->data);
+ }
+
+ if (!ret)
+ ret = au1xmmc_send_command(host, 0, mrq->cmd, mrq->data);
+
+ if (ret) {
+ mrq->cmd->error = ret;
+ au1xmmc_finish_request(host);
+ }
+}
+
+static void au1xmmc_reset_controller(struct au1xmmc_host *host)
+{
+ /* Apply the clock */
+ __raw_writel(SD_ENABLE_CE, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
+
+ __raw_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
+ mdelay(5);
+
+ __raw_writel(~0, HOST_STATUS(host));
+ wmb(); /* drain writebuffer */
+
+ __raw_writel(0, HOST_BLKSIZE(host));
+ __raw_writel(0x001fffff, HOST_TIMEOUT(host));
+ wmb(); /* drain writebuffer */
+
+ __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+
+ __raw_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
+
+ __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+
+ /* Configure interrupts */
+ __raw_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
+}
+
+
+static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+ u32 config2;
+
+ if (ios->power_mode == MMC_POWER_OFF)
+ au1xmmc_set_power(host, 0);
+ else if (ios->power_mode == MMC_POWER_ON) {
+ au1xmmc_set_power(host, 1);
+ }
+
+ if (ios->clock && ios->clock != host->clock) {
+ au1xmmc_set_clock(host, ios->clock);
+ host->clock = ios->clock;
+ }
+
+ config2 = __raw_readl(HOST_CONFIG2(host));
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_8:
+ config2 |= SD_CONFIG2_BB;
+ break;
+ case MMC_BUS_WIDTH_4:
+ config2 &= ~SD_CONFIG2_BB;
+ config2 |= SD_CONFIG2_WB;
+ break;
+ case MMC_BUS_WIDTH_1:
+ config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB);
+ break;
+ }
+ __raw_writel(config2, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+}
+
+#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
+#define STATUS_DATA_IN (SD_STATUS_NE)
+#define STATUS_DATA_OUT (SD_STATUS_TH)
+
+static irqreturn_t au1xmmc_irq(int irq, void *dev_id)
+{
+ struct au1xmmc_host *host = dev_id;
+ u32 status;
+
+ status = __raw_readl(HOST_STATUS(host));
+
+ if (!(status & SD_STATUS_I))
+ return IRQ_NONE; /* not ours */
+
+ if (status & SD_STATUS_SI) /* SDIO */
+ mmc_signal_sdio_irq(host->mmc);
+
+ if (host->mrq && (status & STATUS_TIMEOUT)) {
+ if (status & SD_STATUS_RAT)
+ host->mrq->cmd->error = -ETIMEDOUT;
+ else if (status & SD_STATUS_DT)
+ host->mrq->data->error = -ETIMEDOUT;
+
+ /* In PIO mode, interrupts might still be enabled */
+ IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
+
+ /* IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); */
+ tasklet_schedule(&host->finish_task);
+ }
+#if 0
+ else if (status & SD_STATUS_DD) {
+ /* Sometimes we get a DD before a NE in PIO mode */
+ if (!(host->flags & HOST_F_DMA) && (status & SD_STATUS_NE))
+ au1xmmc_receive_pio(host);
+ else {
+ au1xmmc_data_complete(host, status);
+ /* tasklet_schedule(&host->data_task); */
+ }
+ }
+#endif
+ else if (status & SD_STATUS_CR) {
+ if (host->status == HOST_S_CMD)
+ au1xmmc_cmd_complete(host, status);
+
+ } else if (!(host->flags & HOST_F_DMA)) {
+ if ((host->flags & HOST_F_XMIT) && (status & STATUS_DATA_OUT))
+ au1xmmc_send_pio(host);
+ else if ((host->flags & HOST_F_RECV) && (status & STATUS_DATA_IN))
+ au1xmmc_receive_pio(host);
+
+ } else if (status & 0x203F3C70) {
+ DBG("Unhandled status %8.8x\n", host->pdev->id,
+ status);
+ }
+
+ __raw_writel(status, HOST_STATUS(host));
+ wmb(); /* drain writebuffer */
+
+ return IRQ_HANDLED;
+}
+
+/* 8bit memory DMA device */
+static dbdev_tab_t au1xmmc_mem_dbdev = {
+ .dev_id = DSCR_CMD0_ALWAYS,
+ .dev_flags = DEV_FLAGS_ANYUSE,
+ .dev_tsize = 0,
+ .dev_devwidth = 8,
+ .dev_physaddr = 0x00000000,
+ .dev_intlevel = 0,
+ .dev_intpolarity = 0,
+};
+static int memid;
+
+static void au1xmmc_dbdma_callback(int irq, void *dev_id)
+{
+ struct au1xmmc_host *host = (struct au1xmmc_host *)dev_id;
+
+ /* Avoid spurious interrupts */
+ if (!host->mrq)
+ return;
+
+ if (host->flags & HOST_F_STOP)
+ SEND_STOP(host);
+
+ tasklet_schedule(&host->data_task);
+}
+
+static int au1xmmc_dbdma_init(struct au1xmmc_host *host)
+{
+ struct resource *res;
+ int txid, rxid;
+
+ res = platform_get_resource(host->pdev, IORESOURCE_DMA, 0);
+ if (!res)
+ return -ENODEV;
+ txid = res->start;
+
+ res = platform_get_resource(host->pdev, IORESOURCE_DMA, 1);
+ if (!res)
+ return -ENODEV;
+ rxid = res->start;
+
+ if (!memid)
+ return -ENODEV;
+
+ host->tx_chan = au1xxx_dbdma_chan_alloc(memid, txid,
+ au1xmmc_dbdma_callback, (void *)host);
+ if (!host->tx_chan) {
+ dev_err(&host->pdev->dev, "cannot allocate TX DMA\n");
+ return -ENODEV;
+ }
+
+ host->rx_chan = au1xxx_dbdma_chan_alloc(rxid, memid,
+ au1xmmc_dbdma_callback, (void *)host);
+ if (!host->rx_chan) {
+ dev_err(&host->pdev->dev, "cannot allocate RX DMA\n");
+ au1xxx_dbdma_chan_free(host->tx_chan);
+ return -ENODEV;
+ }
+
+ au1xxx_dbdma_set_devwidth(host->tx_chan, 8);
+ au1xxx_dbdma_set_devwidth(host->rx_chan, 8);
+
+ au1xxx_dbdma_ring_alloc(host->tx_chan, AU1XMMC_DESCRIPTOR_COUNT);
+ au1xxx_dbdma_ring_alloc(host->rx_chan, AU1XMMC_DESCRIPTOR_COUNT);
+
+ /* DBDMA is good to go */
+ host->flags |= HOST_F_DMA | HOST_F_DBDMA;
+
+ return 0;
+}
+
+static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host)
+{
+ if (host->flags & HOST_F_DMA) {
+ host->flags &= ~HOST_F_DMA;
+ au1xxx_dbdma_chan_free(host->tx_chan);
+ au1xxx_dbdma_chan_free(host->rx_chan);
+ }
+}
+
+static void au1xmmc_enable_sdio_irq(struct mmc_host *mmc, int en)
+{
+ struct au1xmmc_host *host = mmc_priv(mmc);
+
+ if (en)
+ IRQ_ON(host, SD_CONFIG_SI);
+ else
+ IRQ_OFF(host, SD_CONFIG_SI);
+}
+
+static const struct mmc_host_ops au1xmmc_ops = {
+ .request = au1xmmc_request,
+ .set_ios = au1xmmc_set_ios,
+ .get_ro = au1xmmc_card_readonly,
+ .get_cd = au1xmmc_card_inserted,
+ .enable_sdio_irq = au1xmmc_enable_sdio_irq,
+};
+
+static int au1xmmc_probe(struct platform_device *pdev)
+{
+ struct mmc_host *mmc;
+ struct au1xmmc_host *host;
+ struct resource *r;
+ int ret, iflag;
+
+ mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
+ if (!mmc) {
+ dev_err(&pdev->dev, "no memory for mmc_host\n");
+ ret = -ENOMEM;
+ goto out0;
+ }
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->platdata = pdev->dev.platform_data;
+ host->pdev = pdev;
+
+ ret = -ENODEV;
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r) {
+ dev_err(&pdev->dev, "no mmio defined\n");
+ goto out1;
+ }
+
+ host->ioarea = request_mem_region(r->start, resource_size(r),
+ pdev->name);
+ if (!host->ioarea) {
+ dev_err(&pdev->dev, "mmio already in use\n");
+ goto out1;
+ }
+
+ host->iobase = ioremap(r->start, 0x3c);
+ if (!host->iobase) {
+ dev_err(&pdev->dev, "cannot remap mmio\n");
+ goto out2;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!r) {
+ dev_err(&pdev->dev, "no IRQ defined\n");
+ goto out3;
+ }
+ host->irq = r->start;
+
+ mmc->ops = &au1xmmc_ops;
+
+ mmc->f_min = 450000;
+ mmc->f_max = 24000000;
+
+ mmc->max_blk_size = 2048;
+ mmc->max_blk_count = 512;
+
+ mmc->ocr_avail = AU1XMMC_OCR;
+ mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
+
+ iflag = IRQF_SHARED; /* Au1100/Au1200: one int for both ctrls */
+
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1100:
+ mmc->max_seg_size = AU1100_MMC_DESCRIPTOR_SIZE;
+ break;
+ case ALCHEMY_CPU_AU1200:
+ mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
+ break;
+ case ALCHEMY_CPU_AU1300:
+ iflag = 0; /* nothing is shared */
+ mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
+ mmc->f_max = 52000000;
+ if (host->ioarea->start == AU1100_SD0_PHYS_ADDR)
+ mmc->caps |= MMC_CAP_8_BIT_DATA;
+ break;
+ }
+
+ ret = request_irq(host->irq, au1xmmc_irq, iflag, DRIVER_NAME, host);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot grab IRQ\n");
+ goto out3;
+ }
+
+ host->clk = clk_get(&pdev->dev, ALCHEMY_PERIPH_CLK);
+ if (IS_ERR(host->clk)) {
+ dev_err(&pdev->dev, "cannot find clock\n");
+ ret = PTR_ERR(host->clk);
+ goto out_irq;
+ }
+
+ ret = clk_prepare_enable(host->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot enable clock\n");
+ goto out_clk;
+ }
+
+ host->status = HOST_S_IDLE;
+
+ /* board-specific carddetect setup, if any */
+ if (host->platdata && host->platdata->cd_setup) {
+ ret = host->platdata->cd_setup(mmc, 1);
+ if (ret) {
+ dev_warn(&pdev->dev, "board CD setup failed\n");
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+ }
+ } else
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+
+ /* platform may not be able to use all advertised caps */
+ if (host->platdata)
+ mmc->caps &= ~(host->platdata->mask_host_caps);
+
+ tasklet_init(&host->data_task, au1xmmc_tasklet_data,
+ (unsigned long)host);
+
+ tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
+ (unsigned long)host);
+
+ if (has_dbdma()) {
+ ret = au1xmmc_dbdma_init(host);
+ if (ret)
+ pr_info(DRIVER_NAME ": DBDMA init failed; using PIO\n");
+ }
+
+#ifdef CONFIG_LEDS_CLASS
+ if (host->platdata && host->platdata->led) {
+ struct led_classdev *led = host->platdata->led;
+ led->name = mmc_hostname(mmc);
+ led->brightness = LED_OFF;
+ led->default_trigger = mmc_hostname(mmc);
+ ret = led_classdev_register(mmc_dev(mmc), led);
+ if (ret)
+ goto out5;
+ }
+#endif
+
+ au1xmmc_reset_controller(host);
+
+ ret = mmc_add_host(mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot add mmc host\n");
+ goto out6;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+ pr_info(DRIVER_NAME ": MMC Controller %d set up at %p"
+ " (mode=%s)\n", pdev->id, host->iobase,
+ host->flags & HOST_F_DMA ? "dma" : "pio");
+
+ return 0; /* all ok */
+
+out6:
+#ifdef CONFIG_LEDS_CLASS
+ if (host->platdata && host->platdata->led)
+ led_classdev_unregister(host->platdata->led);
+out5:
+#endif
+ __raw_writel(0, HOST_ENABLE(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+
+ if (host->flags & HOST_F_DBDMA)
+ au1xmmc_dbdma_shutdown(host);
+
+ tasklet_kill(&host->data_task);
+ tasklet_kill(&host->finish_task);
+
+ if (host->platdata && host->platdata->cd_setup &&
+ !(mmc->caps & MMC_CAP_NEEDS_POLL))
+ host->platdata->cd_setup(mmc, 0);
+out_clk:
+ clk_disable_unprepare(host->clk);
+ clk_put(host->clk);
+out_irq:
+ free_irq(host->irq, host);
+out3:
+ iounmap((void *)host->iobase);
+out2:
+ release_resource(host->ioarea);
+ kfree(host->ioarea);
+out1:
+ mmc_free_host(mmc);
+out0:
+ return ret;
+}
+
+static int au1xmmc_remove(struct platform_device *pdev)
+{
+ struct au1xmmc_host *host = platform_get_drvdata(pdev);
+
+ if (host) {
+ mmc_remove_host(host->mmc);
+
+#ifdef CONFIG_LEDS_CLASS
+ if (host->platdata && host->platdata->led)
+ led_classdev_unregister(host->platdata->led);
+#endif
+
+ if (host->platdata && host->platdata->cd_setup &&
+ !(host->mmc->caps & MMC_CAP_NEEDS_POLL))
+ host->platdata->cd_setup(host->mmc, 0);
+
+ __raw_writel(0, HOST_ENABLE(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+
+ tasklet_kill(&host->data_task);
+ tasklet_kill(&host->finish_task);
+
+ if (host->flags & HOST_F_DBDMA)
+ au1xmmc_dbdma_shutdown(host);
+
+ au1xmmc_set_power(host, 0);
+
+ clk_disable_unprepare(host->clk);
+ clk_put(host->clk);
+
+ free_irq(host->irq, host);
+ iounmap((void *)host->iobase);
+ release_resource(host->ioarea);
+ kfree(host->ioarea);
+
+ mmc_free_host(host->mmc);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int au1xmmc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct au1xmmc_host *host = platform_get_drvdata(pdev);
+
+ __raw_writel(0, HOST_CONFIG2(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0xffffffff, HOST_STATUS(host));
+ __raw_writel(0, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
+
+ return 0;
+}
+
+static int au1xmmc_resume(struct platform_device *pdev)
+{
+ struct au1xmmc_host *host = platform_get_drvdata(pdev);
+
+ au1xmmc_reset_controller(host);
+
+ return 0;
+}
+#else
+#define au1xmmc_suspend NULL
+#define au1xmmc_resume NULL
+#endif
+
+static struct platform_driver au1xmmc_driver = {
+ .probe = au1xmmc_probe,
+ .remove = au1xmmc_remove,
+ .suspend = au1xmmc_suspend,
+ .resume = au1xmmc_resume,
+ .driver = {
+ .name = DRIVER_NAME,
+ },
+};
+
+static int __init au1xmmc_init(void)
+{
+ if (has_dbdma()) {
+ /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
+ * of 8 bits. And since devices are shared, we need to create
+ * our own to avoid freaking out other devices.
+ */
+ memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
+ if (!memid)
+ pr_err("au1xmmc: cannot add memory dbdma\n");
+ }
+ return platform_driver_register(&au1xmmc_driver);
+}
+
+static void __exit au1xmmc_exit(void)
+{
+ if (has_dbdma() && memid)
+ au1xxx_ddma_del_device(memid);
+
+ platform_driver_unregister(&au1xmmc_driver);
+}
+
+module_init(au1xmmc_init);
+module_exit(au1xmmc_exit);
+
+MODULE_AUTHOR("Advanced Micro Devices, Inc");
+MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:au1xxx-mmc");