summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/omap_hsmmc.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host/omap_hsmmc.c')
-rw-r--r--drivers/mmc/host/omap_hsmmc.c2344
1 files changed, 2344 insertions, 0 deletions
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
new file mode 100644
index 000000000..9df2b6801
--- /dev/null
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -0,0 +1,2344 @@
+/*
+ * drivers/mmc/host/omap_hsmmc.c
+ *
+ * Driver for OMAP2430/3430 MMC controller.
+ *
+ * Copyright (C) 2007 Texas Instruments.
+ *
+ * Authors:
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ * Madhusudhan <madhu.cr@ti.com>
+ * Mohit Jalori <mjalori@ti.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/debugfs.h>
+#include <linux/dmaengine.h>
+#include <linux/seq_file.h>
+#include <linux/sizes.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/timer.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/of_device.h>
+#include <linux/omap-dmaengine.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/core.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/slot-gpio.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_data/hsmmc-omap.h>
+
+/* OMAP HSMMC Host Controller Registers */
+#define OMAP_HSMMC_SYSSTATUS 0x0014
+#define OMAP_HSMMC_CON 0x002C
+#define OMAP_HSMMC_SDMASA 0x0100
+#define OMAP_HSMMC_BLK 0x0104
+#define OMAP_HSMMC_ARG 0x0108
+#define OMAP_HSMMC_CMD 0x010C
+#define OMAP_HSMMC_RSP10 0x0110
+#define OMAP_HSMMC_RSP32 0x0114
+#define OMAP_HSMMC_RSP54 0x0118
+#define OMAP_HSMMC_RSP76 0x011C
+#define OMAP_HSMMC_DATA 0x0120
+#define OMAP_HSMMC_PSTATE 0x0124
+#define OMAP_HSMMC_HCTL 0x0128
+#define OMAP_HSMMC_SYSCTL 0x012C
+#define OMAP_HSMMC_STAT 0x0130
+#define OMAP_HSMMC_IE 0x0134
+#define OMAP_HSMMC_ISE 0x0138
+#define OMAP_HSMMC_AC12 0x013C
+#define OMAP_HSMMC_CAPA 0x0140
+
+#define VS18 (1 << 26)
+#define VS30 (1 << 25)
+#define HSS (1 << 21)
+#define SDVS18 (0x5 << 9)
+#define SDVS30 (0x6 << 9)
+#define SDVS33 (0x7 << 9)
+#define SDVS_MASK 0x00000E00
+#define SDVSCLR 0xFFFFF1FF
+#define SDVSDET 0x00000400
+#define AUTOIDLE 0x1
+#define SDBP (1 << 8)
+#define DTO 0xe
+#define ICE 0x1
+#define ICS 0x2
+#define CEN (1 << 2)
+#define CLKD_MAX 0x3FF /* max clock divisor: 1023 */
+#define CLKD_MASK 0x0000FFC0
+#define CLKD_SHIFT 6
+#define DTO_MASK 0x000F0000
+#define DTO_SHIFT 16
+#define INIT_STREAM (1 << 1)
+#define ACEN_ACMD23 (2 << 2)
+#define DP_SELECT (1 << 21)
+#define DDIR (1 << 4)
+#define DMAE 0x1
+#define MSBS (1 << 5)
+#define BCE (1 << 1)
+#define FOUR_BIT (1 << 1)
+#define HSPE (1 << 2)
+#define IWE (1 << 24)
+#define DDR (1 << 19)
+#define CLKEXTFREE (1 << 16)
+#define CTPL (1 << 11)
+#define DW8 (1 << 5)
+#define OD 0x1
+#define STAT_CLEAR 0xFFFFFFFF
+#define INIT_STREAM_CMD 0x00000000
+#define DUAL_VOLT_OCR_BIT 7
+#define SRC (1 << 25)
+#define SRD (1 << 26)
+#define SOFTRESET (1 << 1)
+
+/* PSTATE */
+#define DLEV_DAT(x) (1 << (20 + (x)))
+
+/* Interrupt masks for IE and ISE register */
+#define CC_EN (1 << 0)
+#define TC_EN (1 << 1)
+#define BWR_EN (1 << 4)
+#define BRR_EN (1 << 5)
+#define CIRQ_EN (1 << 8)
+#define ERR_EN (1 << 15)
+#define CTO_EN (1 << 16)
+#define CCRC_EN (1 << 17)
+#define CEB_EN (1 << 18)
+#define CIE_EN (1 << 19)
+#define DTO_EN (1 << 20)
+#define DCRC_EN (1 << 21)
+#define DEB_EN (1 << 22)
+#define ACE_EN (1 << 24)
+#define CERR_EN (1 << 28)
+#define BADA_EN (1 << 29)
+
+#define INT_EN_MASK (BADA_EN | CERR_EN | ACE_EN | DEB_EN | DCRC_EN |\
+ DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \
+ BRR_EN | BWR_EN | TC_EN | CC_EN)
+
+#define CNI (1 << 7)
+#define ACIE (1 << 4)
+#define ACEB (1 << 3)
+#define ACCE (1 << 2)
+#define ACTO (1 << 1)
+#define ACNE (1 << 0)
+
+#define MMC_AUTOSUSPEND_DELAY 100
+#define MMC_TIMEOUT_MS 20 /* 20 mSec */
+#define MMC_TIMEOUT_US 20000 /* 20000 micro Sec */
+#define OMAP_MMC_MIN_CLOCK 400000
+#define OMAP_MMC_MAX_CLOCK 52000000
+#define DRIVER_NAME "omap_hsmmc"
+
+#define VDD_1V8 1800000 /* 180000 uV */
+#define VDD_3V0 3000000 /* 300000 uV */
+#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1)
+
+/*
+ * One controller can have multiple slots, like on some omap boards using
+ * omap.c controller driver. Luckily this is not currently done on any known
+ * omap_hsmmc.c device.
+ */
+#define mmc_pdata(host) host->pdata
+
+/*
+ * MMC Host controller read/write API's
+ */
+#define OMAP_HSMMC_READ(base, reg) \
+ __raw_readl((base) + OMAP_HSMMC_##reg)
+
+#define OMAP_HSMMC_WRITE(base, reg, val) \
+ __raw_writel((val), (base) + OMAP_HSMMC_##reg)
+
+struct omap_hsmmc_next {
+ unsigned int dma_len;
+ s32 cookie;
+};
+
+struct omap_hsmmc_host {
+ struct device *dev;
+ struct mmc_host *mmc;
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_data *data;
+ struct clk *fclk;
+ struct clk *dbclk;
+ /*
+ * vcc == configured supply
+ * vcc_aux == optional
+ * - MMC1, supply for DAT4..DAT7
+ * - MMC2/MMC2, external level shifter voltage supply, for
+ * chip (SDIO, eMMC, etc) or transceiver (MMC2 only)
+ */
+ struct regulator *vcc;
+ struct regulator *vcc_aux;
+ struct regulator *pbias;
+ bool pbias_enabled;
+ void __iomem *base;
+ resource_size_t mapbase;
+ spinlock_t irq_lock; /* Prevent races with irq handler */
+ unsigned int dma_len;
+ unsigned int dma_sg_idx;
+ unsigned char bus_mode;
+ unsigned char power_mode;
+ int suspended;
+ u32 con;
+ u32 hctl;
+ u32 sysctl;
+ u32 capa;
+ int irq;
+ int wake_irq;
+ int use_dma, dma_ch;
+ struct dma_chan *tx_chan;
+ struct dma_chan *rx_chan;
+ int response_busy;
+ int context_loss;
+ int protect_card;
+ int reqs_blocked;
+ int use_reg;
+ int req_in_progress;
+ unsigned long clk_rate;
+ unsigned int flags;
+#define AUTO_CMD23 (1 << 0) /* Auto CMD23 support */
+#define HSMMC_SDIO_IRQ_ENABLED (1 << 1) /* SDIO irq enabled */
+#define HSMMC_WAKE_IRQ_ENABLED (1 << 2)
+ struct omap_hsmmc_next next_data;
+ struct omap_hsmmc_platform_data *pdata;
+
+ /* return MMC cover switch state, can be NULL if not supported.
+ *
+ * possible return values:
+ * 0 - closed
+ * 1 - open
+ */
+ int (*get_cover_state)(struct device *dev);
+
+ int (*card_detect)(struct device *dev);
+};
+
+struct omap_mmc_of_data {
+ u32 reg_offset;
+ u8 controller_flags;
+};
+
+static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host);
+
+static int omap_hsmmc_card_detect(struct device *dev)
+{
+ struct omap_hsmmc_host *host = dev_get_drvdata(dev);
+
+ return mmc_gpio_get_cd(host->mmc);
+}
+
+static int omap_hsmmc_get_cover_state(struct device *dev)
+{
+ struct omap_hsmmc_host *host = dev_get_drvdata(dev);
+
+ return mmc_gpio_get_cd(host->mmc);
+}
+
+#ifdef CONFIG_REGULATOR
+
+static int omap_hsmmc_set_power(struct device *dev, int power_on, int vdd)
+{
+ struct omap_hsmmc_host *host =
+ platform_get_drvdata(to_platform_device(dev));
+ int ret = 0;
+
+ /*
+ * If we don't see a Vcc regulator, assume it's a fixed
+ * voltage always-on regulator.
+ */
+ if (!host->vcc)
+ return 0;
+
+ if (mmc_pdata(host)->before_set_reg)
+ mmc_pdata(host)->before_set_reg(dev, power_on, vdd);
+
+ if (host->pbias) {
+ if (host->pbias_enabled == 1) {
+ ret = regulator_disable(host->pbias);
+ if (!ret)
+ host->pbias_enabled = 0;
+ }
+ regulator_set_voltage(host->pbias, VDD_3V0, VDD_3V0);
+ }
+
+ /*
+ * Assume Vcc regulator is used only to power the card ... OMAP
+ * VDDS is used to power the pins, optionally with a transceiver to
+ * support cards using voltages other than VDDS (1.8V nominal). When a
+ * transceiver is used, DAT3..7 are muxed as transceiver control pins.
+ *
+ * In some cases this regulator won't support enable/disable;
+ * e.g. it's a fixed rail for a WLAN chip.
+ *
+ * In other cases vcc_aux switches interface power. Example, for
+ * eMMC cards it represents VccQ. Sometimes transceivers or SDIO
+ * chips/cards need an interface voltage rail too.
+ */
+ if (power_on) {
+ if (host->vcc)
+ ret = mmc_regulator_set_ocr(host->mmc, host->vcc, vdd);
+ /* Enable interface voltage rail, if needed */
+ if (ret == 0 && host->vcc_aux) {
+ ret = regulator_enable(host->vcc_aux);
+ if (ret < 0 && host->vcc)
+ ret = mmc_regulator_set_ocr(host->mmc,
+ host->vcc, 0);
+ }
+ } else {
+ /* Shut down the rail */
+ if (host->vcc_aux)
+ ret = regulator_disable(host->vcc_aux);
+ if (host->vcc) {
+ /* Then proceed to shut down the local regulator */
+ ret = mmc_regulator_set_ocr(host->mmc,
+ host->vcc, 0);
+ }
+ }
+
+ if (host->pbias) {
+ if (vdd <= VDD_165_195)
+ ret = regulator_set_voltage(host->pbias, VDD_1V8,
+ VDD_1V8);
+ else
+ ret = regulator_set_voltage(host->pbias, VDD_3V0,
+ VDD_3V0);
+ if (ret < 0)
+ goto error_set_power;
+
+ if (host->pbias_enabled == 0) {
+ ret = regulator_enable(host->pbias);
+ if (!ret)
+ host->pbias_enabled = 1;
+ }
+ }
+
+ if (mmc_pdata(host)->after_set_reg)
+ mmc_pdata(host)->after_set_reg(dev, power_on, vdd);
+
+error_set_power:
+ return ret;
+}
+
+static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
+{
+ struct regulator *reg;
+ int ocr_value = 0;
+
+ reg = devm_regulator_get(host->dev, "vmmc");
+ if (IS_ERR(reg)) {
+ dev_err(host->dev, "unable to get vmmc regulator %ld\n",
+ PTR_ERR(reg));
+ return PTR_ERR(reg);
+ } else {
+ host->vcc = reg;
+ ocr_value = mmc_regulator_get_ocrmask(reg);
+ if (!mmc_pdata(host)->ocr_mask) {
+ mmc_pdata(host)->ocr_mask = ocr_value;
+ } else {
+ if (!(mmc_pdata(host)->ocr_mask & ocr_value)) {
+ dev_err(host->dev, "ocrmask %x is not supported\n",
+ mmc_pdata(host)->ocr_mask);
+ mmc_pdata(host)->ocr_mask = 0;
+ return -EINVAL;
+ }
+ }
+ }
+ mmc_pdata(host)->set_power = omap_hsmmc_set_power;
+
+ /* Allow an aux regulator */
+ reg = devm_regulator_get_optional(host->dev, "vmmc_aux");
+ host->vcc_aux = IS_ERR(reg) ? NULL : reg;
+
+ reg = devm_regulator_get_optional(host->dev, "pbias");
+ host->pbias = IS_ERR(reg) ? NULL : reg;
+
+ /* For eMMC do not power off when not in sleep state */
+ if (mmc_pdata(host)->no_regulator_off_init)
+ return 0;
+ /*
+ * To disable boot_on regulator, enable regulator
+ * to increase usecount and then disable it.
+ */
+ if ((host->vcc && regulator_is_enabled(host->vcc) > 0) ||
+ (host->vcc_aux && regulator_is_enabled(host->vcc_aux))) {
+ int vdd = ffs(mmc_pdata(host)->ocr_mask) - 1;
+
+ mmc_pdata(host)->set_power(host->dev, 1, vdd);
+ mmc_pdata(host)->set_power(host->dev, 0, 0);
+ }
+
+ return 0;
+}
+
+static void omap_hsmmc_reg_put(struct omap_hsmmc_host *host)
+{
+ mmc_pdata(host)->set_power = NULL;
+}
+
+static inline int omap_hsmmc_have_reg(void)
+{
+ return 1;
+}
+
+#else
+
+static inline int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
+{
+ return -EINVAL;
+}
+
+static inline void omap_hsmmc_reg_put(struct omap_hsmmc_host *host)
+{
+}
+
+static inline int omap_hsmmc_have_reg(void)
+{
+ return 0;
+}
+
+#endif
+
+static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id);
+
+static int omap_hsmmc_gpio_init(struct mmc_host *mmc,
+ struct omap_hsmmc_host *host,
+ struct omap_hsmmc_platform_data *pdata)
+{
+ int ret;
+
+ if (gpio_is_valid(pdata->gpio_cod)) {
+ ret = mmc_gpio_request_cd(mmc, pdata->gpio_cod, 0);
+ if (ret)
+ return ret;
+
+ host->get_cover_state = omap_hsmmc_get_cover_state;
+ mmc_gpio_set_cd_isr(mmc, omap_hsmmc_cover_irq);
+ } else if (gpio_is_valid(pdata->gpio_cd)) {
+ ret = mmc_gpio_request_cd(mmc, pdata->gpio_cd, 0);
+ if (ret)
+ return ret;
+
+ host->card_detect = omap_hsmmc_card_detect;
+ }
+
+ if (gpio_is_valid(pdata->gpio_wp)) {
+ ret = mmc_gpio_request_ro(mmc, pdata->gpio_wp);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/*
+ * Start clock to the card
+ */
+static void omap_hsmmc_start_clock(struct omap_hsmmc_host *host)
+{
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | CEN);
+}
+
+/*
+ * Stop clock to the card
+ */
+static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host)
+{
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
+ if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
+ dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n");
+}
+
+static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host,
+ struct mmc_command *cmd)
+{
+ u32 irq_mask = INT_EN_MASK;
+ unsigned long flags;
+
+ if (host->use_dma)
+ irq_mask &= ~(BRR_EN | BWR_EN);
+
+ /* Disable timeout for erases */
+ if (cmd->opcode == MMC_ERASE)
+ irq_mask &= ~DTO_EN;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
+
+ /* latch pending CIRQ, but don't signal MMC core */
+ if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
+ irq_mask |= CIRQ_EN;
+ OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+}
+
+static void omap_hsmmc_disable_irq(struct omap_hsmmc_host *host)
+{
+ u32 irq_mask = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ /* no transfer running but need to keep cirq if enabled */
+ if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
+ irq_mask |= CIRQ_EN;
+ OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
+ OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+}
+
+/* Calculate divisor for the given clock frequency */
+static u16 calc_divisor(struct omap_hsmmc_host *host, struct mmc_ios *ios)
+{
+ u16 dsor = 0;
+
+ if (ios->clock) {
+ dsor = DIV_ROUND_UP(clk_get_rate(host->fclk), ios->clock);
+ if (dsor > CLKD_MAX)
+ dsor = CLKD_MAX;
+ }
+
+ return dsor;
+}
+
+static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+ unsigned long regval;
+ unsigned long timeout;
+ unsigned long clkdiv;
+
+ dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock);
+
+ omap_hsmmc_stop_clock(host);
+
+ regval = OMAP_HSMMC_READ(host->base, SYSCTL);
+ regval = regval & ~(CLKD_MASK | DTO_MASK);
+ clkdiv = calc_divisor(host, ios);
+ regval = regval | (clkdiv << 6) | (DTO << 16);
+ OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
+
+ /* Wait till the ICS bit is set */
+ timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+ while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
+ && time_before(jiffies, timeout))
+ cpu_relax();
+
+ /*
+ * Enable High-Speed Support
+ * Pre-Requisites
+ * - Controller should support High-Speed-Enable Bit
+ * - Controller should not be using DDR Mode
+ * - Controller should advertise that it supports High Speed
+ * in capabilities register
+ * - MMC/SD clock coming out of controller > 25MHz
+ */
+ if ((mmc_pdata(host)->features & HSMMC_HAS_HSPE_SUPPORT) &&
+ (ios->timing != MMC_TIMING_MMC_DDR52) &&
+ (ios->timing != MMC_TIMING_UHS_DDR50) &&
+ ((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) {
+ regval = OMAP_HSMMC_READ(host->base, HCTL);
+ if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000)
+ regval |= HSPE;
+ else
+ regval &= ~HSPE;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL, regval);
+ }
+
+ omap_hsmmc_start_clock(host);
+}
+
+static void omap_hsmmc_set_bus_width(struct omap_hsmmc_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+ u32 con;
+
+ con = OMAP_HSMMC_READ(host->base, CON);
+ if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_UHS_DDR50)
+ con |= DDR; /* configure in DDR mode */
+ else
+ con &= ~DDR;
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_8:
+ OMAP_HSMMC_WRITE(host->base, CON, con | DW8);
+ break;
+ case MMC_BUS_WIDTH_4:
+ OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
+ break;
+ case MMC_BUS_WIDTH_1:
+ OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
+ break;
+ }
+}
+
+static void omap_hsmmc_set_bus_mode(struct omap_hsmmc_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+ u32 con;
+
+ con = OMAP_HSMMC_READ(host->base, CON);
+ if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
+ OMAP_HSMMC_WRITE(host->base, CON, con | OD);
+ else
+ OMAP_HSMMC_WRITE(host->base, CON, con & ~OD);
+}
+
+#ifdef CONFIG_PM
+
+/*
+ * Restore the MMC host context, if it was lost as result of a
+ * power state change.
+ */
+static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+ u32 hctl, capa;
+ unsigned long timeout;
+
+ if (host->con == OMAP_HSMMC_READ(host->base, CON) &&
+ host->hctl == OMAP_HSMMC_READ(host->base, HCTL) &&
+ host->sysctl == OMAP_HSMMC_READ(host->base, SYSCTL) &&
+ host->capa == OMAP_HSMMC_READ(host->base, CAPA))
+ return 0;
+
+ host->context_loss++;
+
+ if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
+ if (host->power_mode != MMC_POWER_OFF &&
+ (1 << ios->vdd) <= MMC_VDD_23_24)
+ hctl = SDVS18;
+ else
+ hctl = SDVS30;
+ capa = VS30 | VS18;
+ } else {
+ hctl = SDVS18;
+ capa = VS18;
+ }
+
+ if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
+ hctl |= IWE;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | hctl);
+
+ OMAP_HSMMC_WRITE(host->base, CAPA,
+ OMAP_HSMMC_READ(host->base, CAPA) | capa);
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+
+ timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+ while ((OMAP_HSMMC_READ(host->base, HCTL) & SDBP) != SDBP
+ && time_before(jiffies, timeout))
+ ;
+
+ OMAP_HSMMC_WRITE(host->base, ISE, 0);
+ OMAP_HSMMC_WRITE(host->base, IE, 0);
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+
+ /* Do not initialize card-specific things if the power is off */
+ if (host->power_mode == MMC_POWER_OFF)
+ goto out;
+
+ omap_hsmmc_set_bus_width(host);
+
+ omap_hsmmc_set_clock(host);
+
+ omap_hsmmc_set_bus_mode(host);
+
+out:
+ dev_dbg(mmc_dev(host->mmc), "context is restored: restore count %d\n",
+ host->context_loss);
+ return 0;
+}
+
+/*
+ * Save the MMC host context (store the number of power state changes so far).
+ */
+static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
+{
+ host->con = OMAP_HSMMC_READ(host->base, CON);
+ host->hctl = OMAP_HSMMC_READ(host->base, HCTL);
+ host->sysctl = OMAP_HSMMC_READ(host->base, SYSCTL);
+ host->capa = OMAP_HSMMC_READ(host->base, CAPA);
+}
+
+#else
+
+static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
+{
+ return 0;
+}
+
+static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
+{
+}
+
+#endif
+
+/*
+ * Send init stream sequence to card
+ * before sending IDLE command
+ */
+static void send_init_stream(struct omap_hsmmc_host *host)
+{
+ int reg = 0;
+ unsigned long timeout;
+
+ if (host->protect_card)
+ return;
+
+ disable_irq(host->irq);
+
+ OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
+ OMAP_HSMMC_WRITE(host->base, CON,
+ OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM);
+ OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD);
+
+ timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+ while ((reg != CC_EN) && time_before(jiffies, timeout))
+ reg = OMAP_HSMMC_READ(host->base, STAT) & CC_EN;
+
+ OMAP_HSMMC_WRITE(host->base, CON,
+ OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM);
+
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_READ(host->base, STAT);
+
+ enable_irq(host->irq);
+}
+
+static inline
+int omap_hsmmc_cover_is_closed(struct omap_hsmmc_host *host)
+{
+ int r = 1;
+
+ if (host->get_cover_state)
+ r = host->get_cover_state(host->dev);
+ return r;
+}
+
+static ssize_t
+omap_hsmmc_show_cover_switch(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ return sprintf(buf, "%s\n",
+ omap_hsmmc_cover_is_closed(host) ? "closed" : "open");
+}
+
+static DEVICE_ATTR(cover_switch, S_IRUGO, omap_hsmmc_show_cover_switch, NULL);
+
+static ssize_t
+omap_hsmmc_show_slot_name(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ return sprintf(buf, "%s\n", mmc_pdata(host)->name);
+}
+
+static DEVICE_ATTR(slot_name, S_IRUGO, omap_hsmmc_show_slot_name, NULL);
+
+/*
+ * Configure the response type and send the cmd.
+ */
+static void
+omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd,
+ struct mmc_data *data)
+{
+ int cmdreg = 0, resptype = 0, cmdtype = 0;
+
+ dev_vdbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n",
+ mmc_hostname(host->mmc), cmd->opcode, cmd->arg);
+ host->cmd = cmd;
+
+ omap_hsmmc_enable_irq(host, cmd);
+
+ host->response_busy = 0;
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136)
+ resptype = 1;
+ else if (cmd->flags & MMC_RSP_BUSY) {
+ resptype = 3;
+ host->response_busy = 1;
+ } else
+ resptype = 2;
+ }
+
+ /*
+ * Unlike OMAP1 controller, the cmdtype does not seem to be based on
+ * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
+ * a val of 0x3, rest 0x0.
+ */
+ if (cmd == host->mrq->stop)
+ cmdtype = 0x3;
+
+ cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
+
+ if ((host->flags & AUTO_CMD23) && mmc_op_multi(cmd->opcode) &&
+ host->mrq->sbc) {
+ cmdreg |= ACEN_ACMD23;
+ OMAP_HSMMC_WRITE(host->base, SDMASA, host->mrq->sbc->arg);
+ }
+ if (data) {
+ cmdreg |= DP_SELECT | MSBS | BCE;
+ if (data->flags & MMC_DATA_READ)
+ cmdreg |= DDIR;
+ else
+ cmdreg &= ~(DDIR);
+ }
+
+ if (host->use_dma)
+ cmdreg |= DMAE;
+
+ host->req_in_progress = 1;
+
+ OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg);
+ OMAP_HSMMC_WRITE(host->base, CMD, cmdreg);
+}
+
+static int
+omap_hsmmc_get_dma_dir(struct omap_hsmmc_host *host, struct mmc_data *data)
+{
+ if (data->flags & MMC_DATA_WRITE)
+ return DMA_TO_DEVICE;
+ else
+ return DMA_FROM_DEVICE;
+}
+
+static struct dma_chan *omap_hsmmc_get_dma_chan(struct omap_hsmmc_host *host,
+ struct mmc_data *data)
+{
+ return data->flags & MMC_DATA_WRITE ? host->tx_chan : host->rx_chan;
+}
+
+static void omap_hsmmc_request_done(struct omap_hsmmc_host *host, struct mmc_request *mrq)
+{
+ int dma_ch;
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ host->req_in_progress = 0;
+ dma_ch = host->dma_ch;
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+
+ omap_hsmmc_disable_irq(host);
+ /* Do not complete the request if DMA is still in progress */
+ if (mrq->data && host->use_dma && dma_ch != -1)
+ return;
+ host->mrq = NULL;
+ mmc_request_done(host->mmc, mrq);
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+}
+
+/*
+ * Notify the transfer complete to MMC core
+ */
+static void
+omap_hsmmc_xfer_done(struct omap_hsmmc_host *host, struct mmc_data *data)
+{
+ if (!data) {
+ struct mmc_request *mrq = host->mrq;
+
+ /* TC before CC from CMD6 - don't know why, but it happens */
+ if (host->cmd && host->cmd->opcode == 6 &&
+ host->response_busy) {
+ host->response_busy = 0;
+ return;
+ }
+
+ omap_hsmmc_request_done(host, mrq);
+ return;
+ }
+
+ host->data = NULL;
+
+ if (!data->error)
+ data->bytes_xfered += data->blocks * (data->blksz);
+ else
+ data->bytes_xfered = 0;
+
+ if (data->stop && (data->error || !host->mrq->sbc))
+ omap_hsmmc_start_command(host, data->stop, NULL);
+ else
+ omap_hsmmc_request_done(host, data->mrq);
+}
+
+/*
+ * Notify the core about command completion
+ */
+static void
+omap_hsmmc_cmd_done(struct omap_hsmmc_host *host, struct mmc_command *cmd)
+{
+ if (host->mrq->sbc && (host->cmd == host->mrq->sbc) &&
+ !host->mrq->sbc->error && !(host->flags & AUTO_CMD23)) {
+ host->cmd = NULL;
+ omap_hsmmc_start_dma_transfer(host);
+ omap_hsmmc_start_command(host, host->mrq->cmd,
+ host->mrq->data);
+ return;
+ }
+
+ host->cmd = NULL;
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ /* response type 2 */
+ cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10);
+ cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32);
+ cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54);
+ cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76);
+ } else {
+ /* response types 1, 1b, 3, 4, 5, 6 */
+ cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10);
+ }
+ }
+ if ((host->data == NULL && !host->response_busy) || cmd->error)
+ omap_hsmmc_request_done(host, host->mrq);
+}
+
+/*
+ * DMA clean up for command errors
+ */
+static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host *host, int errno)
+{
+ int dma_ch;
+ unsigned long flags;
+
+ host->data->error = errno;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ dma_ch = host->dma_ch;
+ host->dma_ch = -1;
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+
+ if (host->use_dma && dma_ch != -1) {
+ struct dma_chan *chan = omap_hsmmc_get_dma_chan(host, host->data);
+
+ dmaengine_terminate_all(chan);
+ dma_unmap_sg(chan->device->dev,
+ host->data->sg, host->data->sg_len,
+ omap_hsmmc_get_dma_dir(host, host->data));
+
+ host->data->host_cookie = 0;
+ }
+ host->data = NULL;
+}
+
+/*
+ * Readable error output
+ */
+#ifdef CONFIG_MMC_DEBUG
+static void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host, u32 status)
+{
+ /* --- means reserved bit without definition at documentation */
+ static const char *omap_hsmmc_status_bits[] = {
+ "CC" , "TC" , "BGE", "---", "BWR" , "BRR" , "---" , "---" ,
+ "CIRQ", "OBI" , "---", "---", "---" , "---" , "---" , "ERRI",
+ "CTO" , "CCRC", "CEB", "CIE", "DTO" , "DCRC", "DEB" , "---" ,
+ "ACE" , "---" , "---", "---", "CERR", "BADA", "---" , "---"
+ };
+ char res[256];
+ char *buf = res;
+ int len, i;
+
+ len = sprintf(buf, "MMC IRQ 0x%x :", status);
+ buf += len;
+
+ for (i = 0; i < ARRAY_SIZE(omap_hsmmc_status_bits); i++)
+ if (status & (1 << i)) {
+ len = sprintf(buf, " %s", omap_hsmmc_status_bits[i]);
+ buf += len;
+ }
+
+ dev_vdbg(mmc_dev(host->mmc), "%s\n", res);
+}
+#else
+static inline void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host,
+ u32 status)
+{
+}
+#endif /* CONFIG_MMC_DEBUG */
+
+/*
+ * MMC controller internal state machines reset
+ *
+ * Used to reset command or data internal state machines, using respectively
+ * SRC or SRD bit of SYSCTL register
+ * Can be called from interrupt context
+ */
+static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host *host,
+ unsigned long bit)
+{
+ unsigned long i = 0;
+ unsigned long limit = MMC_TIMEOUT_US;
+
+ OMAP_HSMMC_WRITE(host->base, SYSCTL,
+ OMAP_HSMMC_READ(host->base, SYSCTL) | bit);
+
+ /*
+ * OMAP4 ES2 and greater has an updated reset logic.
+ * Monitor a 0->1 transition first
+ */
+ if (mmc_pdata(host)->features & HSMMC_HAS_UPDATED_RESET) {
+ while ((!(OMAP_HSMMC_READ(host->base, SYSCTL) & bit))
+ && (i++ < limit))
+ udelay(1);
+ }
+ i = 0;
+
+ while ((OMAP_HSMMC_READ(host->base, SYSCTL) & bit) &&
+ (i++ < limit))
+ udelay(1);
+
+ if (OMAP_HSMMC_READ(host->base, SYSCTL) & bit)
+ dev_err(mmc_dev(host->mmc),
+ "Timeout waiting on controller reset in %s\n",
+ __func__);
+}
+
+static void hsmmc_command_incomplete(struct omap_hsmmc_host *host,
+ int err, int end_cmd)
+{
+ if (end_cmd) {
+ omap_hsmmc_reset_controller_fsm(host, SRC);
+ if (host->cmd)
+ host->cmd->error = err;
+ }
+
+ if (host->data) {
+ omap_hsmmc_reset_controller_fsm(host, SRD);
+ omap_hsmmc_dma_cleanup(host, err);
+ } else if (host->mrq && host->mrq->cmd)
+ host->mrq->cmd->error = err;
+}
+
+static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status)
+{
+ struct mmc_data *data;
+ int end_cmd = 0, end_trans = 0;
+ int error = 0;
+
+ data = host->data;
+ dev_vdbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
+
+ if (status & ERR_EN) {
+ omap_hsmmc_dbg_report_irq(host, status);
+
+ if (status & (CTO_EN | CCRC_EN))
+ end_cmd = 1;
+ if (status & (CTO_EN | DTO_EN))
+ hsmmc_command_incomplete(host, -ETIMEDOUT, end_cmd);
+ else if (status & (CCRC_EN | DCRC_EN))
+ hsmmc_command_incomplete(host, -EILSEQ, end_cmd);
+
+ if (status & ACE_EN) {
+ u32 ac12;
+ ac12 = OMAP_HSMMC_READ(host->base, AC12);
+ if (!(ac12 & ACNE) && host->mrq->sbc) {
+ end_cmd = 1;
+ if (ac12 & ACTO)
+ error = -ETIMEDOUT;
+ else if (ac12 & (ACCE | ACEB | ACIE))
+ error = -EILSEQ;
+ host->mrq->sbc->error = error;
+ hsmmc_command_incomplete(host, error, end_cmd);
+ }
+ dev_dbg(mmc_dev(host->mmc), "AC12 err: 0x%x\n", ac12);
+ }
+ if (host->data || host->response_busy) {
+ end_trans = !end_cmd;
+ host->response_busy = 0;
+ }
+ }
+
+ OMAP_HSMMC_WRITE(host->base, STAT, status);
+ if (end_cmd || ((status & CC_EN) && host->cmd))
+ omap_hsmmc_cmd_done(host, host->cmd);
+ if ((end_trans || (status & TC_EN)) && host->mrq)
+ omap_hsmmc_xfer_done(host, data);
+}
+
+/*
+ * MMC controller IRQ handler
+ */
+static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id)
+{
+ struct omap_hsmmc_host *host = dev_id;
+ int status;
+
+ status = OMAP_HSMMC_READ(host->base, STAT);
+ while (status & (INT_EN_MASK | CIRQ_EN)) {
+ if (host->req_in_progress)
+ omap_hsmmc_do_irq(host, status);
+
+ if (status & CIRQ_EN)
+ mmc_signal_sdio_irq(host->mmc);
+
+ /* Flush posted write */
+ status = OMAP_HSMMC_READ(host->base, STAT);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t omap_hsmmc_wake_irq(int irq, void *dev_id)
+{
+ struct omap_hsmmc_host *host = dev_id;
+
+ /* cirq is level triggered, disable to avoid infinite loop */
+ spin_lock(&host->irq_lock);
+ if (host->flags & HSMMC_WAKE_IRQ_ENABLED) {
+ disable_irq_nosync(host->wake_irq);
+ host->flags &= ~HSMMC_WAKE_IRQ_ENABLED;
+ }
+ spin_unlock(&host->irq_lock);
+ pm_request_resume(host->dev); /* no use counter */
+
+ return IRQ_HANDLED;
+}
+
+static void set_sd_bus_power(struct omap_hsmmc_host *host)
+{
+ unsigned long i;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+ for (i = 0; i < loops_per_jiffy; i++) {
+ if (OMAP_HSMMC_READ(host->base, HCTL) & SDBP)
+ break;
+ cpu_relax();
+ }
+}
+
+/*
+ * Switch MMC interface voltage ... only relevant for MMC1.
+ *
+ * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver.
+ * The MMC2 transceiver controls are used instead of DAT4..DAT7.
+ * Some chips, like eMMC ones, use internal transceivers.
+ */
+static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd)
+{
+ u32 reg_val = 0;
+ int ret;
+
+ /* Disable the clocks */
+ pm_runtime_put_sync(host->dev);
+ if (host->dbclk)
+ clk_disable_unprepare(host->dbclk);
+
+ /* Turn the power off */
+ ret = mmc_pdata(host)->set_power(host->dev, 0, 0);
+
+ /* Turn the power ON with given VDD 1.8 or 3.0v */
+ if (!ret)
+ ret = mmc_pdata(host)->set_power(host->dev, 1, vdd);
+ pm_runtime_get_sync(host->dev);
+ if (host->dbclk)
+ clk_prepare_enable(host->dbclk);
+
+ if (ret != 0)
+ goto err;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
+ reg_val = OMAP_HSMMC_READ(host->base, HCTL);
+
+ /*
+ * If a MMC dual voltage card is detected, the set_ios fn calls
+ * this fn with VDD bit set for 1.8V. Upon card removal from the
+ * slot, omap_hsmmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
+ *
+ * Cope with a bit of slop in the range ... per data sheets:
+ * - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max,
+ * but recommended values are 1.71V to 1.89V
+ * - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max,
+ * but recommended values are 2.7V to 3.3V
+ *
+ * Board setup code shouldn't permit anything very out-of-range.
+ * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the
+ * middle range) but VSIM can't power DAT4..DAT7 at more than 3V.
+ */
+ if ((1 << vdd) <= MMC_VDD_23_24)
+ reg_val |= SDVS18;
+ else
+ reg_val |= SDVS30;
+
+ OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
+ set_sd_bus_power(host);
+
+ return 0;
+err:
+ dev_err(mmc_dev(host->mmc), "Unable to switch operating voltage\n");
+ return ret;
+}
+
+/* Protect the card while the cover is open */
+static void omap_hsmmc_protect_card(struct omap_hsmmc_host *host)
+{
+ if (!host->get_cover_state)
+ return;
+
+ host->reqs_blocked = 0;
+ if (host->get_cover_state(host->dev)) {
+ if (host->protect_card) {
+ dev_info(host->dev, "%s: cover is closed, "
+ "card is now accessible\n",
+ mmc_hostname(host->mmc));
+ host->protect_card = 0;
+ }
+ } else {
+ if (!host->protect_card) {
+ dev_info(host->dev, "%s: cover is open, "
+ "card is now inaccessible\n",
+ mmc_hostname(host->mmc));
+ host->protect_card = 1;
+ }
+ }
+}
+
+/*
+ * irq handler when (cell-phone) cover is mounted/removed
+ */
+static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id)
+{
+ struct omap_hsmmc_host *host = dev_id;
+
+ sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
+
+ omap_hsmmc_protect_card(host);
+ mmc_detect_change(host->mmc, (HZ * 200) / 1000);
+ return IRQ_HANDLED;
+}
+
+static void omap_hsmmc_dma_callback(void *param)
+{
+ struct omap_hsmmc_host *host = param;
+ struct dma_chan *chan;
+ struct mmc_data *data;
+ int req_in_progress;
+
+ spin_lock_irq(&host->irq_lock);
+ if (host->dma_ch < 0) {
+ spin_unlock_irq(&host->irq_lock);
+ return;
+ }
+
+ data = host->mrq->data;
+ chan = omap_hsmmc_get_dma_chan(host, data);
+ if (!data->host_cookie)
+ dma_unmap_sg(chan->device->dev,
+ data->sg, data->sg_len,
+ omap_hsmmc_get_dma_dir(host, data));
+
+ req_in_progress = host->req_in_progress;
+ host->dma_ch = -1;
+ spin_unlock_irq(&host->irq_lock);
+
+ /* If DMA has finished after TC, complete the request */
+ if (!req_in_progress) {
+ struct mmc_request *mrq = host->mrq;
+
+ host->mrq = NULL;
+ mmc_request_done(host->mmc, mrq);
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+ }
+}
+
+static int omap_hsmmc_pre_dma_transfer(struct omap_hsmmc_host *host,
+ struct mmc_data *data,
+ struct omap_hsmmc_next *next,
+ struct dma_chan *chan)
+{
+ int dma_len;
+
+ if (!next && data->host_cookie &&
+ data->host_cookie != host->next_data.cookie) {
+ dev_warn(host->dev, "[%s] invalid cookie: data->host_cookie %d"
+ " host->next_data.cookie %d\n",
+ __func__, data->host_cookie, host->next_data.cookie);
+ data->host_cookie = 0;
+ }
+
+ /* Check if next job is already prepared */
+ if (next || data->host_cookie != host->next_data.cookie) {
+ dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len,
+ omap_hsmmc_get_dma_dir(host, data));
+
+ } else {
+ dma_len = host->next_data.dma_len;
+ host->next_data.dma_len = 0;
+ }
+
+
+ if (dma_len == 0)
+ return -EINVAL;
+
+ if (next) {
+ next->dma_len = dma_len;
+ data->host_cookie = ++next->cookie < 0 ? 1 : next->cookie;
+ } else
+ host->dma_len = dma_len;
+
+ return 0;
+}
+
+/*
+ * Routine to configure and start DMA for the MMC card
+ */
+static int omap_hsmmc_setup_dma_transfer(struct omap_hsmmc_host *host,
+ struct mmc_request *req)
+{
+ struct dma_slave_config cfg;
+ struct dma_async_tx_descriptor *tx;
+ int ret = 0, i;
+ struct mmc_data *data = req->data;
+ struct dma_chan *chan;
+
+ /* Sanity check: all the SG entries must be aligned by block size. */
+ for (i = 0; i < data->sg_len; i++) {
+ struct scatterlist *sgl;
+
+ sgl = data->sg + i;
+ if (sgl->length % data->blksz)
+ return -EINVAL;
+ }
+ if ((data->blksz % 4) != 0)
+ /* REVISIT: The MMC buffer increments only when MSB is written.
+ * Return error for blksz which is non multiple of four.
+ */
+ return -EINVAL;
+
+ BUG_ON(host->dma_ch != -1);
+
+ chan = omap_hsmmc_get_dma_chan(host, data);
+
+ cfg.src_addr = host->mapbase + OMAP_HSMMC_DATA;
+ cfg.dst_addr = host->mapbase + OMAP_HSMMC_DATA;
+ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ cfg.src_maxburst = data->blksz / 4;
+ cfg.dst_maxburst = data->blksz / 4;
+
+ ret = dmaengine_slave_config(chan, &cfg);
+ if (ret)
+ return ret;
+
+ ret = omap_hsmmc_pre_dma_transfer(host, data, NULL, chan);
+ if (ret)
+ return ret;
+
+ tx = dmaengine_prep_slave_sg(chan, data->sg, data->sg_len,
+ data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!tx) {
+ dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n");
+ /* FIXME: cleanup */
+ return -1;
+ }
+
+ tx->callback = omap_hsmmc_dma_callback;
+ tx->callback_param = host;
+
+ /* Does not fail */
+ dmaengine_submit(tx);
+
+ host->dma_ch = 1;
+
+ return 0;
+}
+
+static void set_data_timeout(struct omap_hsmmc_host *host,
+ unsigned int timeout_ns,
+ unsigned int timeout_clks)
+{
+ unsigned int timeout, cycle_ns;
+ uint32_t reg, clkd, dto = 0;
+
+ reg = OMAP_HSMMC_READ(host->base, SYSCTL);
+ clkd = (reg & CLKD_MASK) >> CLKD_SHIFT;
+ if (clkd == 0)
+ clkd = 1;
+
+ cycle_ns = 1000000000 / (host->clk_rate / clkd);
+ timeout = timeout_ns / cycle_ns;
+ timeout += timeout_clks;
+ if (timeout) {
+ while ((timeout & 0x80000000) == 0) {
+ dto += 1;
+ timeout <<= 1;
+ }
+ dto = 31 - dto;
+ timeout <<= 1;
+ if (timeout && dto)
+ dto += 1;
+ if (dto >= 13)
+ dto -= 13;
+ else
+ dto = 0;
+ if (dto > 14)
+ dto = 14;
+ }
+
+ reg &= ~DTO_MASK;
+ reg |= dto << DTO_SHIFT;
+ OMAP_HSMMC_WRITE(host->base, SYSCTL, reg);
+}
+
+static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host)
+{
+ struct mmc_request *req = host->mrq;
+ struct dma_chan *chan;
+
+ if (!req->data)
+ return;
+ OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz)
+ | (req->data->blocks << 16));
+ set_data_timeout(host, req->data->timeout_ns,
+ req->data->timeout_clks);
+ chan = omap_hsmmc_get_dma_chan(host, req->data);
+ dma_async_issue_pending(chan);
+}
+
+/*
+ * Configure block length for MMC/SD cards and initiate the transfer.
+ */
+static int
+omap_hsmmc_prepare_data(struct omap_hsmmc_host *host, struct mmc_request *req)
+{
+ int ret;
+ host->data = req->data;
+
+ if (req->data == NULL) {
+ OMAP_HSMMC_WRITE(host->base, BLK, 0);
+ /*
+ * Set an arbitrary 100ms data timeout for commands with
+ * busy signal.
+ */
+ if (req->cmd->flags & MMC_RSP_BUSY)
+ set_data_timeout(host, 100000000U, 0);
+ return 0;
+ }
+
+ if (host->use_dma) {
+ ret = omap_hsmmc_setup_dma_transfer(host, req);
+ if (ret != 0) {
+ dev_err(mmc_dev(host->mmc), "MMC start dma failure\n");
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static void omap_hsmmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
+ int err)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+ struct mmc_data *data = mrq->data;
+
+ if (host->use_dma && data->host_cookie) {
+ struct dma_chan *c = omap_hsmmc_get_dma_chan(host, data);
+
+ dma_unmap_sg(c->device->dev, data->sg, data->sg_len,
+ omap_hsmmc_get_dma_dir(host, data));
+ data->host_cookie = 0;
+ }
+}
+
+static void omap_hsmmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq,
+ bool is_first_req)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ if (mrq->data->host_cookie) {
+ mrq->data->host_cookie = 0;
+ return ;
+ }
+
+ if (host->use_dma) {
+ struct dma_chan *c = omap_hsmmc_get_dma_chan(host, mrq->data);
+
+ if (omap_hsmmc_pre_dma_transfer(host, mrq->data,
+ &host->next_data, c))
+ mrq->data->host_cookie = 0;
+ }
+}
+
+/*
+ * Request function. for read/write operation
+ */
+static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+ int err;
+
+ BUG_ON(host->req_in_progress);
+ BUG_ON(host->dma_ch != -1);
+ pm_runtime_get_sync(host->dev);
+ if (host->protect_card) {
+ if (host->reqs_blocked < 3) {
+ /*
+ * Ensure the controller is left in a consistent
+ * state by resetting the command and data state
+ * machines.
+ */
+ omap_hsmmc_reset_controller_fsm(host, SRD);
+ omap_hsmmc_reset_controller_fsm(host, SRC);
+ host->reqs_blocked += 1;
+ }
+ req->cmd->error = -EBADF;
+ if (req->data)
+ req->data->error = -EBADF;
+ req->cmd->retries = 0;
+ mmc_request_done(mmc, req);
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+ return;
+ } else if (host->reqs_blocked)
+ host->reqs_blocked = 0;
+ WARN_ON(host->mrq != NULL);
+ host->mrq = req;
+ host->clk_rate = clk_get_rate(host->fclk);
+ err = omap_hsmmc_prepare_data(host, req);
+ if (err) {
+ req->cmd->error = err;
+ if (req->data)
+ req->data->error = err;
+ host->mrq = NULL;
+ mmc_request_done(mmc, req);
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+ return;
+ }
+ if (req->sbc && !(host->flags & AUTO_CMD23)) {
+ omap_hsmmc_start_command(host, req->sbc, NULL);
+ return;
+ }
+
+ omap_hsmmc_start_dma_transfer(host);
+ omap_hsmmc_start_command(host, req->cmd, req->data);
+}
+
+/* Routine to configure clock values. Exposed API to core */
+static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+ int do_send_init_stream = 0;
+
+ pm_runtime_get_sync(host->dev);
+
+ if (ios->power_mode != host->power_mode) {
+ switch (ios->power_mode) {
+ case MMC_POWER_OFF:
+ mmc_pdata(host)->set_power(host->dev, 0, 0);
+ break;
+ case MMC_POWER_UP:
+ mmc_pdata(host)->set_power(host->dev, 1, ios->vdd);
+ break;
+ case MMC_POWER_ON:
+ do_send_init_stream = 1;
+ break;
+ }
+ host->power_mode = ios->power_mode;
+ }
+
+ /* FIXME: set registers based only on changes to ios */
+
+ omap_hsmmc_set_bus_width(host);
+
+ if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
+ /* Only MMC1 can interface at 3V without some flavor
+ * of external transceiver; but they all handle 1.8V.
+ */
+ if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
+ (ios->vdd == DUAL_VOLT_OCR_BIT)) {
+ /*
+ * The mmc_select_voltage fn of the core does
+ * not seem to set the power_mode to
+ * MMC_POWER_UP upon recalculating the voltage.
+ * vdd 1.8v.
+ */
+ if (omap_hsmmc_switch_opcond(host, ios->vdd) != 0)
+ dev_dbg(mmc_dev(host->mmc),
+ "Switch operation failed\n");
+ }
+ }
+
+ omap_hsmmc_set_clock(host);
+
+ if (do_send_init_stream)
+ send_init_stream(host);
+
+ omap_hsmmc_set_bus_mode(host);
+
+ pm_runtime_put_autosuspend(host->dev);
+}
+
+static int omap_hsmmc_get_cd(struct mmc_host *mmc)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ if (!host->card_detect)
+ return -ENOSYS;
+ return host->card_detect(host->dev);
+}
+
+static void omap_hsmmc_init_card(struct mmc_host *mmc, struct mmc_card *card)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ if (mmc_pdata(host)->init_card)
+ mmc_pdata(host)->init_card(card);
+}
+
+static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+ u32 irq_mask, con;
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+
+ con = OMAP_HSMMC_READ(host->base, CON);
+ irq_mask = OMAP_HSMMC_READ(host->base, ISE);
+ if (enable) {
+ host->flags |= HSMMC_SDIO_IRQ_ENABLED;
+ irq_mask |= CIRQ_EN;
+ con |= CTPL | CLKEXTFREE;
+ } else {
+ host->flags &= ~HSMMC_SDIO_IRQ_ENABLED;
+ irq_mask &= ~CIRQ_EN;
+ con &= ~(CTPL | CLKEXTFREE);
+ }
+ OMAP_HSMMC_WRITE(host->base, CON, con);
+ OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
+
+ /*
+ * if enable, piggy back detection on current request
+ * but always disable immediately
+ */
+ if (!host->req_in_progress || !enable)
+ OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
+
+ /* flush posted write */
+ OMAP_HSMMC_READ(host->base, IE);
+
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+}
+
+static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ int ret;
+
+ /*
+ * For omaps with wake-up path, wakeirq will be irq from pinctrl and
+ * for other omaps, wakeirq will be from GPIO (dat line remuxed to
+ * gpio). wakeirq is needed to detect sdio irq in runtime suspend state
+ * with functional clock disabled.
+ */
+ if (!host->dev->of_node || !host->wake_irq)
+ return -ENODEV;
+
+ /* Prevent auto-enabling of IRQ */
+ irq_set_status_flags(host->wake_irq, IRQ_NOAUTOEN);
+ ret = devm_request_irq(host->dev, host->wake_irq, omap_hsmmc_wake_irq,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ mmc_hostname(mmc), host);
+ if (ret) {
+ dev_err(mmc_dev(host->mmc), "Unable to request wake IRQ\n");
+ goto err;
+ }
+
+ /*
+ * Some omaps don't have wake-up path from deeper idle states
+ * and need to remux SDIO DAT1 to GPIO for wake-up from idle.
+ */
+ if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) {
+ struct pinctrl *p = devm_pinctrl_get(host->dev);
+ if (!p) {
+ ret = -ENODEV;
+ goto err_free_irq;
+ }
+ if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_DEFAULT))) {
+ dev_info(host->dev, "missing default pinctrl state\n");
+ devm_pinctrl_put(p);
+ ret = -EINVAL;
+ goto err_free_irq;
+ }
+
+ if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_IDLE))) {
+ dev_info(host->dev, "missing idle pinctrl state\n");
+ devm_pinctrl_put(p);
+ ret = -EINVAL;
+ goto err_free_irq;
+ }
+ devm_pinctrl_put(p);
+ }
+
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) | IWE);
+ return 0;
+
+err_free_irq:
+ devm_free_irq(host->dev, host->wake_irq, host);
+err:
+ dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n");
+ host->wake_irq = 0;
+ return ret;
+}
+
+static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host)
+{
+ u32 hctl, capa, value;
+
+ /* Only MMC1 supports 3.0V */
+ if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
+ hctl = SDVS30;
+ capa = VS30 | VS18;
+ } else {
+ hctl = SDVS18;
+ capa = VS18;
+ }
+
+ value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK;
+ OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl);
+
+ value = OMAP_HSMMC_READ(host->base, CAPA);
+ OMAP_HSMMC_WRITE(host->base, CAPA, value | capa);
+
+ /* Set SD bus power bit */
+ set_sd_bus_power(host);
+}
+
+static int omap_hsmmc_multi_io_quirk(struct mmc_card *card,
+ unsigned int direction, int blk_size)
+{
+ /* This controller can't do multiblock reads due to hw bugs */
+ if (direction == MMC_DATA_READ)
+ return 1;
+
+ return blk_size;
+}
+
+static struct mmc_host_ops omap_hsmmc_ops = {
+ .post_req = omap_hsmmc_post_req,
+ .pre_req = omap_hsmmc_pre_req,
+ .request = omap_hsmmc_request,
+ .set_ios = omap_hsmmc_set_ios,
+ .get_cd = omap_hsmmc_get_cd,
+ .get_ro = mmc_gpio_get_ro,
+ .init_card = omap_hsmmc_init_card,
+ .enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
+};
+
+#ifdef CONFIG_DEBUG_FS
+
+static int omap_hsmmc_regs_show(struct seq_file *s, void *data)
+{
+ struct mmc_host *mmc = s->private;
+ struct omap_hsmmc_host *host = mmc_priv(mmc);
+
+ seq_printf(s, "mmc%d:\n", mmc->index);
+ seq_printf(s, "sdio irq mode\t%s\n",
+ (mmc->caps & MMC_CAP_SDIO_IRQ) ? "interrupt" : "polling");
+
+ if (mmc->caps & MMC_CAP_SDIO_IRQ) {
+ seq_printf(s, "sdio irq \t%s\n",
+ (host->flags & HSMMC_SDIO_IRQ_ENABLED) ? "enabled"
+ : "disabled");
+ }
+ seq_printf(s, "ctx_loss:\t%d\n", host->context_loss);
+
+ pm_runtime_get_sync(host->dev);
+ seq_puts(s, "\nregs:\n");
+ seq_printf(s, "CON:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, CON));
+ seq_printf(s, "PSTATE:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, PSTATE));
+ seq_printf(s, "HCTL:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, HCTL));
+ seq_printf(s, "SYSCTL:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, SYSCTL));
+ seq_printf(s, "IE:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, IE));
+ seq_printf(s, "ISE:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, ISE));
+ seq_printf(s, "CAPA:\t\t0x%08x\n",
+ OMAP_HSMMC_READ(host->base, CAPA));
+
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+
+ return 0;
+}
+
+static int omap_hsmmc_regs_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, omap_hsmmc_regs_show, inode->i_private);
+}
+
+static const struct file_operations mmc_regs_fops = {
+ .open = omap_hsmmc_regs_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void omap_hsmmc_debugfs(struct mmc_host *mmc)
+{
+ if (mmc->debugfs_root)
+ debugfs_create_file("regs", S_IRUSR, mmc->debugfs_root,
+ mmc, &mmc_regs_fops);
+}
+
+#else
+
+static void omap_hsmmc_debugfs(struct mmc_host *mmc)
+{
+}
+
+#endif
+
+#ifdef CONFIG_OF
+static const struct omap_mmc_of_data omap3_pre_es3_mmc_of_data = {
+ /* See 35xx errata 2.1.1.128 in SPRZ278F */
+ .controller_flags = OMAP_HSMMC_BROKEN_MULTIBLOCK_READ,
+};
+
+static const struct omap_mmc_of_data omap4_mmc_of_data = {
+ .reg_offset = 0x100,
+};
+static const struct omap_mmc_of_data am33xx_mmc_of_data = {
+ .reg_offset = 0x100,
+ .controller_flags = OMAP_HSMMC_SWAKEUP_MISSING,
+};
+
+static const struct of_device_id omap_mmc_of_match[] = {
+ {
+ .compatible = "ti,omap2-hsmmc",
+ },
+ {
+ .compatible = "ti,omap3-pre-es3-hsmmc",
+ .data = &omap3_pre_es3_mmc_of_data,
+ },
+ {
+ .compatible = "ti,omap3-hsmmc",
+ },
+ {
+ .compatible = "ti,omap4-hsmmc",
+ .data = &omap4_mmc_of_data,
+ },
+ {
+ .compatible = "ti,am33xx-hsmmc",
+ .data = &am33xx_mmc_of_data,
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, omap_mmc_of_match);
+
+static struct omap_hsmmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
+{
+ struct omap_hsmmc_platform_data *pdata;
+ struct device_node *np = dev->of_node;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM); /* out of memory */
+
+ if (of_find_property(np, "ti,dual-volt", NULL))
+ pdata->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT;
+
+ pdata->gpio_cd = -EINVAL;
+ pdata->gpio_cod = -EINVAL;
+ pdata->gpio_wp = -EINVAL;
+
+ if (of_find_property(np, "ti,non-removable", NULL)) {
+ pdata->nonremovable = true;
+ pdata->no_regulator_off_init = true;
+ }
+
+ if (of_find_property(np, "ti,needs-special-reset", NULL))
+ pdata->features |= HSMMC_HAS_UPDATED_RESET;
+
+ if (of_find_property(np, "ti,needs-special-hs-handling", NULL))
+ pdata->features |= HSMMC_HAS_HSPE_SUPPORT;
+
+ return pdata;
+}
+#else
+static inline struct omap_hsmmc_platform_data
+ *of_get_hsmmc_pdata(struct device *dev)
+{
+ return ERR_PTR(-EINVAL);
+}
+#endif
+
+static int omap_hsmmc_probe(struct platform_device *pdev)
+{
+ struct omap_hsmmc_platform_data *pdata = pdev->dev.platform_data;
+ struct mmc_host *mmc;
+ struct omap_hsmmc_host *host = NULL;
+ struct resource *res;
+ int ret, irq;
+ const struct of_device_id *match;
+ dma_cap_mask_t mask;
+ unsigned tx_req, rx_req;
+ const struct omap_mmc_of_data *data;
+ void __iomem *base;
+
+ match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev);
+ if (match) {
+ pdata = of_get_hsmmc_pdata(&pdev->dev);
+
+ if (IS_ERR(pdata))
+ return PTR_ERR(pdata);
+
+ if (match->data) {
+ data = match->data;
+ pdata->reg_offset = data->reg_offset;
+ pdata->controller_flags |= data->controller_flags;
+ }
+ }
+
+ if (pdata == NULL) {
+ dev_err(&pdev->dev, "Platform Data is missing\n");
+ return -ENXIO;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (res == NULL || irq < 0)
+ return -ENXIO;
+
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ mmc = mmc_alloc_host(sizeof(struct omap_hsmmc_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ret = mmc_of_parse(mmc);
+ if (ret)
+ goto err1;
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->pdata = pdata;
+ host->dev = &pdev->dev;
+ host->use_dma = 1;
+ host->dma_ch = -1;
+ host->irq = irq;
+ host->mapbase = res->start + pdata->reg_offset;
+ host->base = base + pdata->reg_offset;
+ host->power_mode = MMC_POWER_OFF;
+ host->next_data.cookie = 1;
+ host->pbias_enabled = 0;
+
+ ret = omap_hsmmc_gpio_init(mmc, host, pdata);
+ if (ret)
+ goto err_gpio;
+
+ platform_set_drvdata(pdev, host);
+
+ if (pdev->dev.of_node)
+ host->wake_irq = irq_of_parse_and_map(pdev->dev.of_node, 1);
+
+ mmc->ops = &omap_hsmmc_ops;
+
+ mmc->f_min = OMAP_MMC_MIN_CLOCK;
+
+ if (pdata->max_freq > 0)
+ mmc->f_max = pdata->max_freq;
+ else if (mmc->f_max == 0)
+ mmc->f_max = OMAP_MMC_MAX_CLOCK;
+
+ spin_lock_init(&host->irq_lock);
+
+ host->fclk = devm_clk_get(&pdev->dev, "fck");
+ if (IS_ERR(host->fclk)) {
+ ret = PTR_ERR(host->fclk);
+ host->fclk = NULL;
+ goto err1;
+ }
+
+ if (host->pdata->controller_flags & OMAP_HSMMC_BROKEN_MULTIBLOCK_READ) {
+ dev_info(&pdev->dev, "multiblock reads disabled due to 35xx erratum 2.1.1.128; MMC read performance may suffer\n");
+ omap_hsmmc_ops.multi_io_quirk = omap_hsmmc_multi_io_quirk;
+ }
+
+ pm_runtime_enable(host->dev);
+ pm_runtime_get_sync(host->dev);
+ pm_runtime_set_autosuspend_delay(host->dev, MMC_AUTOSUSPEND_DELAY);
+ pm_runtime_use_autosuspend(host->dev);
+
+ omap_hsmmc_context_save(host);
+
+ host->dbclk = devm_clk_get(&pdev->dev, "mmchsdb_fck");
+ /*
+ * MMC can still work without debounce clock.
+ */
+ if (IS_ERR(host->dbclk)) {
+ host->dbclk = NULL;
+ } else if (clk_prepare_enable(host->dbclk) != 0) {
+ dev_warn(mmc_dev(host->mmc), "Failed to enable debounce clk\n");
+ host->dbclk = NULL;
+ }
+
+ /* Since we do only SG emulation, we can have as many segs
+ * as we want. */
+ mmc->max_segs = 1024;
+
+ mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
+ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_req_size;
+
+ mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
+ MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_ERASE;
+
+ mmc->caps |= mmc_pdata(host)->caps;
+ if (mmc->caps & MMC_CAP_8_BIT_DATA)
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+ if (mmc_pdata(host)->nonremovable)
+ mmc->caps |= MMC_CAP_NONREMOVABLE;
+
+ mmc->pm_caps |= mmc_pdata(host)->pm_caps;
+
+ omap_hsmmc_conf_bus_power(host);
+
+ if (!pdev->dev.of_node) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
+ if (!res) {
+ dev_err(mmc_dev(host->mmc), "cannot get DMA TX channel\n");
+ ret = -ENXIO;
+ goto err_irq;
+ }
+ tx_req = res->start;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
+ if (!res) {
+ dev_err(mmc_dev(host->mmc), "cannot get DMA RX channel\n");
+ ret = -ENXIO;
+ goto err_irq;
+ }
+ rx_req = res->start;
+ }
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ host->rx_chan =
+ dma_request_slave_channel_compat(mask, omap_dma_filter_fn,
+ &rx_req, &pdev->dev, "rx");
+
+ if (!host->rx_chan) {
+ dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);
+ ret = -ENXIO;
+ goto err_irq;
+ }
+
+ host->tx_chan =
+ dma_request_slave_channel_compat(mask, omap_dma_filter_fn,
+ &tx_req, &pdev->dev, "tx");
+
+ if (!host->tx_chan) {
+ dev_err(mmc_dev(host->mmc), "unable to obtain TX DMA engine channel %u\n", tx_req);
+ ret = -ENXIO;
+ goto err_irq;
+ }
+
+ /* Request IRQ for MMC operations */
+ ret = devm_request_irq(&pdev->dev, host->irq, omap_hsmmc_irq, 0,
+ mmc_hostname(mmc), host);
+ if (ret) {
+ dev_err(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n");
+ goto err_irq;
+ }
+
+ if (omap_hsmmc_have_reg() && !mmc_pdata(host)->set_power) {
+ ret = omap_hsmmc_reg_get(host);
+ if (ret)
+ goto err_irq;
+ host->use_reg = 1;
+ }
+
+ mmc->ocr_avail = mmc_pdata(host)->ocr_mask;
+
+ omap_hsmmc_disable_irq(host);
+
+ /*
+ * For now, only support SDIO interrupt if we have a separate
+ * wake-up interrupt configured from device tree. This is because
+ * the wake-up interrupt is needed for idle state and some
+ * platforms need special quirks. And we don't want to add new
+ * legacy mux platform init code callbacks any longer as we
+ * are moving to DT based booting anyways.
+ */
+ ret = omap_hsmmc_configure_wake_irq(host);
+ if (!ret)
+ mmc->caps |= MMC_CAP_SDIO_IRQ;
+
+ omap_hsmmc_protect_card(host);
+
+ mmc_add_host(mmc);
+
+ if (mmc_pdata(host)->name != NULL) {
+ ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
+ if (ret < 0)
+ goto err_slot_name;
+ }
+ if (host->get_cover_state) {
+ ret = device_create_file(&mmc->class_dev,
+ &dev_attr_cover_switch);
+ if (ret < 0)
+ goto err_slot_name;
+ }
+
+ omap_hsmmc_debugfs(mmc);
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+
+ return 0;
+
+err_slot_name:
+ mmc_remove_host(mmc);
+ if (host->use_reg)
+ omap_hsmmc_reg_put(host);
+err_irq:
+ if (host->tx_chan)
+ dma_release_channel(host->tx_chan);
+ if (host->rx_chan)
+ dma_release_channel(host->rx_chan);
+ pm_runtime_put_sync(host->dev);
+ pm_runtime_disable(host->dev);
+ if (host->dbclk)
+ clk_disable_unprepare(host->dbclk);
+err1:
+err_gpio:
+ mmc_free_host(mmc);
+err:
+ return ret;
+}
+
+static int omap_hsmmc_remove(struct platform_device *pdev)
+{
+ struct omap_hsmmc_host *host = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(host->dev);
+ mmc_remove_host(host->mmc);
+ if (host->use_reg)
+ omap_hsmmc_reg_put(host);
+
+ if (host->tx_chan)
+ dma_release_channel(host->tx_chan);
+ if (host->rx_chan)
+ dma_release_channel(host->rx_chan);
+
+ pm_runtime_put_sync(host->dev);
+ pm_runtime_disable(host->dev);
+ if (host->dbclk)
+ clk_disable_unprepare(host->dbclk);
+
+ mmc_free_host(host->mmc);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int omap_hsmmc_suspend(struct device *dev)
+{
+ struct omap_hsmmc_host *host = dev_get_drvdata(dev);
+
+ if (!host)
+ return 0;
+
+ pm_runtime_get_sync(host->dev);
+
+ if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) {
+ OMAP_HSMMC_WRITE(host->base, ISE, 0);
+ OMAP_HSMMC_WRITE(host->base, IE, 0);
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_WRITE(host->base, HCTL,
+ OMAP_HSMMC_READ(host->base, HCTL) & ~SDBP);
+ }
+
+ /* do not wake up due to sdio irq */
+ if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
+ !(host->mmc->pm_flags & MMC_PM_WAKE_SDIO_IRQ))
+ disable_irq(host->wake_irq);
+
+ if (host->dbclk)
+ clk_disable_unprepare(host->dbclk);
+
+ pm_runtime_put_sync(host->dev);
+ return 0;
+}
+
+/* Routine to resume the MMC device */
+static int omap_hsmmc_resume(struct device *dev)
+{
+ struct omap_hsmmc_host *host = dev_get_drvdata(dev);
+
+ if (!host)
+ return 0;
+
+ pm_runtime_get_sync(host->dev);
+
+ if (host->dbclk)
+ clk_prepare_enable(host->dbclk);
+
+ if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER))
+ omap_hsmmc_conf_bus_power(host);
+
+ omap_hsmmc_protect_card(host);
+
+ if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
+ !(host->mmc->pm_flags & MMC_PM_WAKE_SDIO_IRQ))
+ enable_irq(host->wake_irq);
+
+ pm_runtime_mark_last_busy(host->dev);
+ pm_runtime_put_autosuspend(host->dev);
+ return 0;
+}
+#endif
+
+static int omap_hsmmc_runtime_suspend(struct device *dev)
+{
+ struct omap_hsmmc_host *host;
+ unsigned long flags;
+ int ret = 0;
+
+ host = platform_get_drvdata(to_platform_device(dev));
+ omap_hsmmc_context_save(host);
+ dev_dbg(dev, "disabled\n");
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
+ (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
+ /* disable sdio irq handling to prevent race */
+ OMAP_HSMMC_WRITE(host->base, ISE, 0);
+ OMAP_HSMMC_WRITE(host->base, IE, 0);
+
+ if (!(OMAP_HSMMC_READ(host->base, PSTATE) & DLEV_DAT(1))) {
+ /*
+ * dat1 line low, pending sdio irq
+ * race condition: possible irq handler running on
+ * multi-core, abort
+ */
+ dev_dbg(dev, "pending sdio irq, abort suspend\n");
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
+ OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
+ pm_runtime_mark_last_busy(dev);
+ ret = -EBUSY;
+ goto abort;
+ }
+
+ pinctrl_pm_select_idle_state(dev);
+
+ WARN_ON(host->flags & HSMMC_WAKE_IRQ_ENABLED);
+ enable_irq(host->wake_irq);
+ host->flags |= HSMMC_WAKE_IRQ_ENABLED;
+ } else {
+ pinctrl_pm_select_idle_state(dev);
+ }
+
+abort:
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+ return ret;
+}
+
+static int omap_hsmmc_runtime_resume(struct device *dev)
+{
+ struct omap_hsmmc_host *host;
+ unsigned long flags;
+
+ host = platform_get_drvdata(to_platform_device(dev));
+ omap_hsmmc_context_restore(host);
+ dev_dbg(dev, "enabled\n");
+
+ spin_lock_irqsave(&host->irq_lock, flags);
+ if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
+ (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
+ /* sdio irq flag can't change while in runtime suspend */
+ if (host->flags & HSMMC_WAKE_IRQ_ENABLED) {
+ disable_irq_nosync(host->wake_irq);
+ host->flags &= ~HSMMC_WAKE_IRQ_ENABLED;
+ }
+
+ pinctrl_pm_select_default_state(host->dev);
+
+ /* irq lost, if pinmux incorrect */
+ OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+ OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
+ OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
+ } else {
+ pinctrl_pm_select_default_state(host->dev);
+ }
+ spin_unlock_irqrestore(&host->irq_lock, flags);
+ return 0;
+}
+
+static struct dev_pm_ops omap_hsmmc_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(omap_hsmmc_suspend, omap_hsmmc_resume)
+ .runtime_suspend = omap_hsmmc_runtime_suspend,
+ .runtime_resume = omap_hsmmc_runtime_resume,
+};
+
+static struct platform_driver omap_hsmmc_driver = {
+ .probe = omap_hsmmc_probe,
+ .remove = omap_hsmmc_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .pm = &omap_hsmmc_dev_pm_ops,
+ .of_match_table = of_match_ptr(omap_mmc_of_match),
+ },
+};
+
+module_platform_driver(omap_hsmmc_driver);
+MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Texas Instruments Inc");