diff options
Diffstat (limited to 'drivers/mtd/nand')
66 files changed, 49410 insertions, 0 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig new file mode 100644 index 000000000..5897d8d8f --- /dev/null +++ b/drivers/mtd/nand/Kconfig @@ -0,0 +1,533 @@ +config MTD_NAND_ECC + tristate + +config MTD_NAND_ECC_SMC + bool "NAND ECC Smart Media byte order" + depends on MTD_NAND_ECC + default n + help + Software ECC according to the Smart Media Specification. + The original Linux implementation had byte 0 and 1 swapped. + + +menuconfig MTD_NAND + tristate "NAND Device Support" + depends on MTD + select MTD_NAND_IDS + select MTD_NAND_ECC + help + This enables support for accessing all type of NAND flash + devices. For further information see + <http://www.linux-mtd.infradead.org/doc/nand.html>. + +if MTD_NAND + +config MTD_NAND_BCH + tristate + select BCH + depends on MTD_NAND_ECC_BCH + default MTD_NAND + +config MTD_NAND_ECC_BCH + bool "Support software BCH ECC" + default n + help + This enables support for software BCH error correction. Binary BCH + codes are more powerful and cpu intensive than traditional Hamming + ECC codes. They are used with NAND devices requiring more than 1 bit + of error correction. + +config MTD_SM_COMMON + tristate + default n + +config MTD_NAND_DENALI + tristate "Support Denali NAND controller" + depends on HAS_DMA + help + Enable support for the Denali NAND controller. This should be + combined with either the PCI or platform drivers to provide device + registration. + +config MTD_NAND_DENALI_PCI + tristate "Support Denali NAND controller on Intel Moorestown" + depends on PCI && MTD_NAND_DENALI + help + Enable the driver for NAND flash on Intel Moorestown, using the + Denali NAND controller core. + +config MTD_NAND_DENALI_DT + tristate "Support Denali NAND controller as a DT device" + depends on HAVE_CLK && MTD_NAND_DENALI + help + Enable the driver for NAND flash on platforms using a Denali NAND + controller as a DT device. + +config MTD_NAND_DENALI_SCRATCH_REG_ADDR + hex "Denali NAND size scratch register address" + default "0xFF108018" + depends on MTD_NAND_DENALI_PCI + help + Some platforms place the NAND chip size in a scratch register + because (some versions of) the driver aren't able to automatically + determine the size of certain chips. Set the address of the + scratch register here to enable this feature. On Intel Moorestown + boards, the scratch register is at 0xFF108018. + +config MTD_NAND_GPIO + tristate "GPIO assisted NAND Flash driver" + depends on GPIOLIB + help + This enables a NAND flash driver where control signals are + connected to GPIO pins, and commands and data are communicated + via a memory mapped interface. + +config MTD_NAND_AMS_DELTA + tristate "NAND Flash device on Amstrad E3" + depends on MACH_AMS_DELTA + default y + help + Support for NAND flash on Amstrad E3 (Delta). + +config MTD_NAND_OMAP2 + tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4" + depends on ARCH_OMAP2PLUS + help + Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4 + platforms. + +config MTD_NAND_OMAP_BCH + depends on MTD_NAND_OMAP2 + bool "Support hardware based BCH error correction" + default n + select BCH + help + This config enables the ELM hardware engine, which can be used to + locate and correct errors when using BCH ECC scheme. This offloads + the cpu from doing ECC error searching and correction. However some + legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine + so this is optional for them. + +config MTD_NAND_OMAP_BCH_BUILD + def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH + +config MTD_NAND_IDS + tristate + +config MTD_NAND_RICOH + tristate "Ricoh xD card reader" + default n + depends on PCI + select MTD_SM_COMMON + help + Enable support for Ricoh R5C852 xD card reader + You also need to enable ether + NAND SSFDC (SmartMedia) read only translation layer' or new + expermental, readwrite + 'SmartMedia/xD new translation layer' + +config MTD_NAND_AU1550 + tristate "Au1550/1200 NAND support" + depends on MIPS_ALCHEMY + help + This enables the driver for the NAND flash controller on the + AMD/Alchemy 1550 SOC. + +config MTD_NAND_BF5XX + tristate "Blackfin on-chip NAND Flash Controller driver" + depends on BF54x || BF52x + help + This enables the Blackfin on-chip NAND flash controller + + No board specific support is done by this driver, each board + must advertise a platform_device for the driver to attach. + + This driver can also be built as a module. If so, the module + will be called bf5xx-nand. + +config MTD_NAND_BF5XX_HWECC + bool "BF5XX NAND Hardware ECC" + default y + depends on MTD_NAND_BF5XX + help + Enable the use of the BF5XX's internal ECC generator when + using NAND. + +config MTD_NAND_BF5XX_BOOTROM_ECC + bool "Use Blackfin BootROM ECC Layout" + default n + depends on MTD_NAND_BF5XX_HWECC + help + If you wish to modify NAND pages and allow the Blackfin on-chip + BootROM to boot from them, say Y here. This is only necessary + if you are booting U-Boot out of NAND and you wish to update + U-Boot from Linux' userspace. Otherwise, you should say N here. + + If unsure, say N. + +config MTD_NAND_S3C2410 + tristate "NAND Flash support for Samsung S3C SoCs" + depends on ARCH_S3C24XX || ARCH_S3C64XX + help + This enables the NAND flash controller on the S3C24xx and S3C64xx + SoCs + + No board specific support is done by this driver, each board + must advertise a platform_device for the driver to attach. + +config MTD_NAND_S3C2410_DEBUG + bool "Samsung S3C NAND driver debug" + depends on MTD_NAND_S3C2410 + help + Enable debugging of the S3C NAND driver + +config MTD_NAND_S3C2410_HWECC + bool "Samsung S3C NAND Hardware ECC" + depends on MTD_NAND_S3C2410 + help + Enable the use of the controller's internal ECC generator when + using NAND. Early versions of the chips have had problems with + incorrect ECC generation, and if using these, the default of + software ECC is preferable. + +config MTD_NAND_NDFC + tristate "NDFC NanD Flash Controller" + depends on 4xx + select MTD_NAND_ECC_SMC + help + NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs + +config MTD_NAND_S3C2410_CLKSTOP + bool "Samsung S3C NAND IDLE clock stop" + depends on MTD_NAND_S3C2410 + default n + help + Stop the clock to the NAND controller when there is no chip + selected to save power. This will mean there is a small delay + when the is NAND chip selected or released, but will save + approximately 5mA of power when there is nothing happening. + +config MTD_NAND_DISKONCHIP + tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)" + depends on HAS_IOMEM + select REED_SOLOMON + select REED_SOLOMON_DEC16 + help + This is a reimplementation of M-Systems DiskOnChip 2000, + Millennium and Millennium Plus as a standard NAND device driver, + as opposed to the earlier self-contained MTD device drivers. + This should enable, among other things, proper JFFS2 operation on + these devices. + +config MTD_NAND_DISKONCHIP_PROBE_ADVANCED + bool "Advanced detection options for DiskOnChip" + depends on MTD_NAND_DISKONCHIP + help + This option allows you to specify nonstandard address at which to + probe for a DiskOnChip, or to change the detection options. You + are unlikely to need any of this unless you are using LinuxBIOS. + Say 'N'. + +config MTD_NAND_DISKONCHIP_PROBE_ADDRESS + hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED + depends on MTD_NAND_DISKONCHIP + default "0" + ---help--- + By default, the probe for DiskOnChip devices will look for a + DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. + This option allows you to specify a single address at which to probe + for the device, which is useful if you have other devices in that + range which get upset when they are probed. + + (Note that on PowerPC, the normal probe will only check at + 0xE4000000.) + + Normally, you should leave this set to zero, to allow the probe at + the normal addresses. + +config MTD_NAND_DISKONCHIP_PROBE_HIGH + bool "Probe high addresses" + depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED + help + By default, the probe for DiskOnChip devices will look for a + DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. + This option changes to make it probe between 0xFFFC8000 and + 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be + useful to you. Say 'N'. + +config MTD_NAND_DISKONCHIP_BBTWRITE + bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP" + depends on MTD_NAND_DISKONCHIP + help + On DiskOnChip devices shipped with the INFTL filesystem (Millennium + and 2000 TSOP/Alon), Linux reserves some space at the end of the + device for the Bad Block Table (BBT). If you have existing INFTL + data on your device (created by non-Linux tools such as M-Systems' + DOS drivers), your data might overlap the area Linux wants to use for + the BBT. If this is a concern for you, leave this option disabled and + Linux will not write BBT data into this area. + The downside of leaving this option disabled is that if bad blocks + are detected by Linux, they will not be recorded in the BBT, which + could cause future problems. + Once you enable this option, new filesystems (INFTL or others, created + in Linux or other operating systems) will not use the reserved area. + The only reason not to enable this option is to prevent damage to + preexisting filesystems. + Even if you leave this disabled, you can enable BBT writes at module + load time (assuming you build diskonchip as a module) with the module + parameter "inftl_bbt_write=1". + +config MTD_NAND_DOCG4 + tristate "Support for DiskOnChip G4" + depends on HAS_IOMEM + select BCH + select BITREVERSE + help + Support for diskonchip G4 nand flash, found in various smartphones and + PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba + Portege G900, Asus P526, and O2 XDA Zinc. + + With this driver you will be able to use UBI and create a ubifs on the + device, so you may wish to consider enabling UBI and UBIFS as well. + + These devices ship with the Mys/Sandisk SAFTL formatting, for which + there is currently no mtd parser, so you may want to use command line + partitioning to segregate write-protected blocks. On the Treo680, the + first five erase blocks (256KiB each) are write-protected, followed + by the block containing the saftl partition table. This is probably + typical. + +config MTD_NAND_SHARPSL + tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" + depends on ARCH_PXA + +config MTD_NAND_CAFE + tristate "NAND support for OLPC CAFÉ chip" + depends on PCI + select REED_SOLOMON + select REED_SOLOMON_DEC16 + help + Use NAND flash attached to the CAFÉ chip designed for the OLPC + laptop. + +config MTD_NAND_CS553X + tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" + depends on X86_32 + help + The CS553x companion chips for the AMD Geode processor + include NAND flash controllers with built-in hardware ECC + capabilities; enabling this option will allow you to use + these. The driver will check the MSRs to verify that the + controller is enabled for NAND, and currently requires that + the controller be in MMIO mode. + + If you say "m", the module will be called cs553x_nand. + +config MTD_NAND_ATMEL + tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32" + depends on ARCH_AT91 || AVR32 + help + Enables support for NAND Flash / Smart Media Card interface + on Atmel AT91 and AVR32 processors. + +config MTD_NAND_PXA3xx + tristate "NAND support on PXA3xx and Armada 370/XP" + depends on PXA3xx || ARCH_MMP || PLAT_ORION + help + This enables the driver for the NAND flash device found on + PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). + +config MTD_NAND_SLC_LPC32XX + tristate "NXP LPC32xx SLC Controller" + depends on ARCH_LPC32XX + help + Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell + chips) NAND controller. This is the default for the PHYTEC 3250 + reference board which contains a NAND256R3A2CZA6 chip. + + Please check the actual NAND chip connected and its support + by the SLC NAND controller. + +config MTD_NAND_MLC_LPC32XX + tristate "NXP LPC32xx MLC Controller" + depends on ARCH_LPC32XX + help + Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND + controller. This is the default for the WORK92105 controller + board. + + Please check the actual NAND chip connected and its support + by the MLC NAND controller. + +config MTD_NAND_CM_X270 + tristate "Support for NAND Flash on CM-X270 modules" + depends on MACH_ARMCORE + +config MTD_NAND_PASEMI + tristate "NAND support for PA Semi PWRficient" + depends on PPC_PASEMI + help + Enables support for NAND Flash interface on PA Semi PWRficient + based boards + +config MTD_NAND_TMIO + tristate "NAND Flash device on Toshiba Mobile IO Controller" + depends on MFD_TMIO + help + Support for NAND flash connected to a Toshiba Mobile IO + Controller in some PDAs, including the Sharp SL6000x. + +config MTD_NAND_NANDSIM + tristate "Support for NAND Flash Simulator" + help + The simulator may simulate various NAND flash chips for the + MTD nand layer. + +config MTD_NAND_GPMI_NAND + tristate "GPMI NAND Flash Controller driver" + depends on MTD_NAND && MXS_DMA + help + Enables NAND Flash support for IMX23, IMX28 or IMX6. + The GPMI controller is very powerful, with the help of BCH + module, it can do the hardware ECC. The GPMI supports several + NAND flashs at the same time. The GPMI may conflicts with other + block, such as SD card. So pay attention to it when you enable + the GPMI. + +config MTD_NAND_BCM47XXNFLASH + tristate "Support for NAND flash on BCM4706 BCMA bus" + depends on BCMA_NFLASH + help + BCMA bus can have various flash memories attached, they are + registered by bcma as platform devices. This enables driver for + NAND flash memories. For now only BCM4706 is supported. + +config MTD_NAND_PLATFORM + tristate "Support for generic platform NAND driver" + depends on HAS_IOMEM + help + This implements a generic NAND driver for on-SOC platform + devices. You will need to provide platform-specific functions + via platform_data. + +config MTD_NAND_ORION + tristate "NAND Flash support for Marvell Orion SoC" + depends on PLAT_ORION + help + This enables the NAND flash controller on Orion machines. + + No board specific support is done by this driver, each board + must advertise a platform_device for the driver to attach. + +config MTD_NAND_FSL_ELBC + tristate "NAND support for Freescale eLBC controllers" + depends on PPC + select FSL_LBC + help + Various Freescale chips, including the 8313, include a NAND Flash + Controller Module with built-in hardware ECC capabilities. + Enabling this option will enable you to use this to control + external NAND devices. + +config MTD_NAND_FSL_IFC + tristate "NAND support for Freescale IFC controller" + depends on MTD_NAND && FSL_SOC + select FSL_IFC + select MEMORY + help + Various Freescale chips e.g P1010, include a NAND Flash machine + with built-in hardware ECC capabilities. + Enabling this option will enable you to use this to control + external NAND devices. + +config MTD_NAND_FSL_UPM + tristate "Support for NAND on Freescale UPM" + depends on PPC_83xx || PPC_85xx + select FSL_LBC + help + Enables support for NAND Flash chips wired onto Freescale PowerPC + processor localbus with User-Programmable Machine support. + +config MTD_NAND_MPC5121_NFC + tristate "MPC5121 built-in NAND Flash Controller support" + depends on PPC_MPC512x + help + This enables the driver for the NAND flash controller on the + MPC5121 SoC. + +config MTD_NAND_MXC + tristate "MXC NAND support" + depends on ARCH_MXC + help + This enables the driver for the NAND flash controller on the + MXC processors. + +config MTD_NAND_SH_FLCTL + tristate "Support for NAND on Renesas SuperH FLCTL" + depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST + depends on HAS_IOMEM + depends on HAS_DMA + help + Several Renesas SuperH CPU has FLCTL. This option enables support + for NAND Flash using FLCTL. + +config MTD_NAND_DAVINCI + tristate "Support NAND on DaVinci/Keystone SoC" + depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) + help + Enable the driver for NAND flash chips on Texas Instruments + DaVinci/Keystone processors. + +config MTD_NAND_TXX9NDFMC + tristate "NAND Flash support for TXx9 SoC" + depends on SOC_TX4938 || SOC_TX4939 + help + This enables the NAND flash controller on the TXx9 SoCs. + +config MTD_NAND_SOCRATES + tristate "Support for NAND on Socrates board" + depends on SOCRATES + help + Enables support for NAND Flash chips wired onto Socrates board. + +config MTD_NAND_NUC900 + tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." + depends on ARCH_W90X900 + help + This enables the driver for the NAND Flash on evaluation board based + on w90p910 / NUC9xx. + +config MTD_NAND_JZ4740 + tristate "Support for JZ4740 SoC NAND controller" + depends on MACH_JZ4740 + help + Enables support for NAND Flash on JZ4740 SoC based boards. + +config MTD_NAND_FSMC + tristate "Support for NAND on ST Micros FSMC" + depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 + help + Enables support for NAND Flash chips on the ST Microelectronics + Flexible Static Memory Controller (FSMC) + +config MTD_NAND_XWAY + tristate "Support for NAND on Lantiq XWAY SoC" + depends on LANTIQ && SOC_TYPE_XWAY + select MTD_NAND_PLATFORM + help + Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached + to the External Bus Unit (EBU). + +config MTD_NAND_SUNXI + tristate "Support for NAND on Allwinner SoCs" + depends on ARCH_SUNXI + help + Enables support for NAND Flash chips on Allwinner SoCs. + +config MTD_NAND_HISI504 + tristate "Support for NAND controller on Hisilicon SoC Hip04" + depends on HAS_DMA + help + Enables support for NAND controller on Hisilicon SoC Hip04. + +endif # MTD_NAND diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile new file mode 100644 index 000000000..582bbd05a --- /dev/null +++ b/drivers/mtd/nand/Makefile @@ -0,0 +1,56 @@ +# +# linux/drivers/nand/Makefile +# + +obj-$(CONFIG_MTD_NAND) += nand.o +obj-$(CONFIG_MTD_NAND_ECC) += nand_ecc.o +obj-$(CONFIG_MTD_NAND_BCH) += nand_bch.o +obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.o +obj-$(CONFIG_MTD_SM_COMMON) += sm_common.o + +obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nand.o +obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o +obj-$(CONFIG_MTD_NAND_DENALI) += denali.o +obj-$(CONFIG_MTD_NAND_DENALI_PCI) += denali_pci.o +obj-$(CONFIG_MTD_NAND_DENALI_DT) += denali_dt.o +obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o +obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o +obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o +obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o +obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o +obj-$(CONFIG_MTD_NAND_DOCG4) += docg4.o +obj-$(CONFIG_MTD_NAND_FSMC) += fsmc_nand.o +obj-$(CONFIG_MTD_NAND_SHARPSL) += sharpsl.o +obj-$(CONFIG_MTD_NAND_NANDSIM) += nandsim.o +obj-$(CONFIG_MTD_NAND_CS553X) += cs553x_nand.o +obj-$(CONFIG_MTD_NAND_NDFC) += ndfc.o +obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o +obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o +obj-$(CONFIG_MTD_NAND_OMAP2) += omap2.o +obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o +obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o +obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o +obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o +obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o +obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o +obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o +obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o +obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o +obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o +obj-$(CONFIG_MTD_NAND_SLC_LPC32XX) += lpc32xx_slc.o +obj-$(CONFIG_MTD_NAND_MLC_LPC32XX) += lpc32xx_mlc.o +obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o +obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o +obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o +obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o +obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o +obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o +obj-$(CONFIG_MTD_NAND_RICOH) += r852.o +obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o +obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/ +obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o +obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/ +obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o +obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o + +nand-objs := nand_base.o nand_bbt.o nand_timings.o diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c new file mode 100644 index 000000000..842f8fe91 --- /dev/null +++ b/drivers/mtd/nand/ams-delta.c @@ -0,0 +1,296 @@ +/* + * drivers/mtd/nand/ams-delta.c + * + * Copyright (C) 2006 Jonathan McDowell <noodles@earth.li> + * + * Derived from drivers/mtd/toto.c + * Converted to platform driver by Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> + * Partially stolen from drivers/mtd/nand/plat_nand.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Overview: + * This is a device driver for the NAND flash device found on the + * Amstrad E3 (Delta). + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/gpio.h> +#include <linux/platform_data/gpio-omap.h> + +#include <asm/io.h> +#include <asm/sizes.h> + +#include <mach/board-ams-delta.h> + +#include <mach/hardware.h> + +/* + * MTD structure for E3 (Delta) + */ +static struct mtd_info *ams_delta_mtd = NULL; + +/* + * Define partitions for flash devices + */ + +static struct mtd_partition partition_info[] = { + { .name = "Kernel", + .offset = 0, + .size = 3 * SZ_1M + SZ_512K }, + { .name = "u-boot", + .offset = 3 * SZ_1M + SZ_512K, + .size = SZ_256K }, + { .name = "u-boot params", + .offset = 3 * SZ_1M + SZ_512K + SZ_256K, + .size = SZ_256K }, + { .name = "Amstrad LDR", + .offset = 4 * SZ_1M, + .size = SZ_256K }, + { .name = "File system", + .offset = 4 * SZ_1M + 1 * SZ_256K, + .size = 27 * SZ_1M }, + { .name = "PBL reserved", + .offset = 32 * SZ_1M - 3 * SZ_256K, + .size = 3 * SZ_256K }, +}; + +static void ams_delta_write_byte(struct mtd_info *mtd, u_char byte) +{ + struct nand_chip *this = mtd->priv; + void __iomem *io_base = this->priv; + + writew(0, io_base + OMAP_MPUIO_IO_CNTL); + writew(byte, this->IO_ADDR_W); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 0); + ndelay(40); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 1); +} + +static u_char ams_delta_read_byte(struct mtd_info *mtd) +{ + u_char res; + struct nand_chip *this = mtd->priv; + void __iomem *io_base = this->priv; + + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 0); + ndelay(40); + writew(~0, io_base + OMAP_MPUIO_IO_CNTL); + res = readw(this->IO_ADDR_R); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 1); + + return res; +} + +static void ams_delta_write_buf(struct mtd_info *mtd, const u_char *buf, + int len) +{ + int i; + + for (i=0; i<len; i++) + ams_delta_write_byte(mtd, buf[i]); +} + +static void ams_delta_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + int i; + + for (i=0; i<len; i++) + buf[i] = ams_delta_read_byte(mtd); +} + +/* + * Command control function + * + * ctrl: + * NAND_NCE: bit 0 -> bit 2 + * NAND_CLE: bit 1 -> bit 7 + * NAND_ALE: bit 2 -> bit 6 + */ +static void ams_delta_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + + if (ctrl & NAND_CTRL_CHANGE) { + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NCE, + (ctrl & NAND_NCE) == 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_CLE, + (ctrl & NAND_CLE) != 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_ALE, + (ctrl & NAND_ALE) != 0); + } + + if (cmd != NAND_CMD_NONE) + ams_delta_write_byte(mtd, cmd); +} + +static int ams_delta_nand_ready(struct mtd_info *mtd) +{ + return gpio_get_value(AMS_DELTA_GPIO_PIN_NAND_RB); +} + +static const struct gpio _mandatory_gpio[] = { + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NCE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nce", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NRE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nre", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWP, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nwp", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nwe", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_ALE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_ale", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_CLE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_cle", + }, +}; + +/* + * Main initialization routine + */ +static int ams_delta_init(struct platform_device *pdev) +{ + struct nand_chip *this; + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + void __iomem *io_base; + int err = 0; + + if (!res) + return -ENXIO; + + /* Allocate memory for MTD device structure and private data */ + ams_delta_mtd = kzalloc(sizeof(struct mtd_info) + + sizeof(struct nand_chip), GFP_KERNEL); + if (!ams_delta_mtd) { + printk (KERN_WARNING "Unable to allocate E3 NAND MTD device structure.\n"); + err = -ENOMEM; + goto out; + } + + ams_delta_mtd->owner = THIS_MODULE; + + /* Get pointer to private data */ + this = (struct nand_chip *) (&ams_delta_mtd[1]); + + /* Link the private data with the MTD structure */ + ams_delta_mtd->priv = this; + + /* + * Don't try to request the memory region from here, + * it should have been already requested from the + * gpio-omap driver and requesting it again would fail. + */ + + io_base = ioremap(res->start, resource_size(res)); + if (io_base == NULL) { + dev_err(&pdev->dev, "ioremap failed\n"); + err = -EIO; + goto out_free; + } + + this->priv = io_base; + + /* Set address of NAND IO lines */ + this->IO_ADDR_R = io_base + OMAP_MPUIO_INPUT_LATCH; + this->IO_ADDR_W = io_base + OMAP_MPUIO_OUTPUT; + this->read_byte = ams_delta_read_byte; + this->write_buf = ams_delta_write_buf; + this->read_buf = ams_delta_read_buf; + this->cmd_ctrl = ams_delta_hwcontrol; + if (gpio_request(AMS_DELTA_GPIO_PIN_NAND_RB, "nand_rdy") == 0) { + this->dev_ready = ams_delta_nand_ready; + } else { + this->dev_ready = NULL; + printk(KERN_NOTICE "Couldn't request gpio for Delta NAND ready.\n"); + } + /* 25 us command delay time */ + this->chip_delay = 30; + this->ecc.mode = NAND_ECC_SOFT; + + platform_set_drvdata(pdev, io_base); + + /* Set chip enabled, but */ + err = gpio_request_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); + if (err) + goto out_gpio; + + /* Scan to find existence of the device */ + if (nand_scan(ams_delta_mtd, 1)) { + err = -ENXIO; + goto out_mtd; + } + + /* Register the partitions */ + mtd_device_register(ams_delta_mtd, partition_info, + ARRAY_SIZE(partition_info)); + + goto out; + + out_mtd: + gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); +out_gpio: + gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB); + iounmap(io_base); +out_free: + kfree(ams_delta_mtd); + out: + return err; +} + +/* + * Clean up routine + */ +static int ams_delta_cleanup(struct platform_device *pdev) +{ + void __iomem *io_base = platform_get_drvdata(pdev); + + /* Release resources, unregister device */ + nand_release(ams_delta_mtd); + + gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); + gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB); + iounmap(io_base); + + /* Free the MTD device structure */ + kfree(ams_delta_mtd); + + return 0; +} + +static struct platform_driver ams_delta_nand_driver = { + .probe = ams_delta_init, + .remove = ams_delta_cleanup, + .driver = { + .name = "ams-delta-nand", + }, +}; + +module_platform_driver(ams_delta_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Jonathan McDowell <noodles@earth.li>"); +MODULE_DESCRIPTION("Glue layer for NAND flash on Amstrad E3 (Delta)"); diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c new file mode 100644 index 000000000..46010bd89 --- /dev/null +++ b/drivers/mtd/nand/atmel_nand.c @@ -0,0 +1,2412 @@ +/* + * Copyright © 2003 Rick Bronson + * + * Derived from drivers/mtd/nand/autcpu12.c + * Copyright © 2001 Thomas Gleixner (gleixner@autronix.de) + * + * Derived from drivers/mtd/spia.c + * Copyright © 2000 Steven J. Hill (sjhill@cotw.com) + * + * + * Add Hardware ECC support for AT91SAM9260 / AT91SAM9263 + * Richard Genoud (richard.genoud@gmail.com), Adeneo Copyright © 2007 + * + * Derived from Das U-Boot source code + * (u-boot-1.1.5/board/atmel/at91sam9263ek/nand.c) + * © Copyright 2006 ATMEL Rousset, Lacressonniere Nicolas + * + * Add Programmable Multibit ECC support for various AT91 SoC + * © Copyright 2012 ATMEL, Hong Xu + * + * Add Nand Flash Controller support for SAMA5 SoC + * © Copyright 2013 ATMEL, Josh Wu (josh.wu@atmel.com) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/of_mtd.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> + +#include <linux/delay.h> +#include <linux/dmaengine.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/platform_data/atmel.h> + +static int use_dma = 1; +module_param(use_dma, int, 0); + +static int on_flash_bbt = 0; +module_param(on_flash_bbt, int, 0); + +/* Register access macros */ +#define ecc_readl(add, reg) \ + __raw_readl(add + ATMEL_ECC_##reg) +#define ecc_writel(add, reg, value) \ + __raw_writel((value), add + ATMEL_ECC_##reg) + +#include "atmel_nand_ecc.h" /* Hardware ECC registers */ +#include "atmel_nand_nfc.h" /* Nand Flash Controller definition */ + +struct atmel_nand_caps { + bool pmecc_correct_erase_page; +}; + +/* oob layout for large page size + * bad block info is on bytes 0 and 1 + * the bytes have to be consecutives to avoid + * several NAND_CMD_RNDOUT during read + */ +static struct nand_ecclayout atmel_oobinfo_large = { + .eccbytes = 4, + .eccpos = {60, 61, 62, 63}, + .oobfree = { + {2, 58} + }, +}; + +/* oob layout for small page size + * bad block info is on bytes 4 and 5 + * the bytes have to be consecutives to avoid + * several NAND_CMD_RNDOUT during read + */ +static struct nand_ecclayout atmel_oobinfo_small = { + .eccbytes = 4, + .eccpos = {0, 1, 2, 3}, + .oobfree = { + {6, 10} + }, +}; + +struct atmel_nfc { + void __iomem *base_cmd_regs; + void __iomem *hsmc_regs; + void *sram_bank0; + dma_addr_t sram_bank0_phys; + bool use_nfc_sram; + bool write_by_sram; + + struct clk *clk; + + bool is_initialized; + struct completion comp_ready; + struct completion comp_cmd_done; + struct completion comp_xfer_done; + + /* Point to the sram bank which include readed data via NFC */ + void *data_in_sram; + bool will_write_sram; +}; +static struct atmel_nfc nand_nfc; + +struct atmel_nand_host { + struct nand_chip nand_chip; + struct mtd_info mtd; + void __iomem *io_base; + dma_addr_t io_phys; + struct atmel_nand_data board; + struct device *dev; + void __iomem *ecc; + + struct completion comp; + struct dma_chan *dma_chan; + + struct atmel_nfc *nfc; + + struct atmel_nand_caps *caps; + bool has_pmecc; + u8 pmecc_corr_cap; + u16 pmecc_sector_size; + bool has_no_lookup_table; + u32 pmecc_lookup_table_offset; + u32 pmecc_lookup_table_offset_512; + u32 pmecc_lookup_table_offset_1024; + + int pmecc_degree; /* Degree of remainders */ + int pmecc_cw_len; /* Length of codeword */ + + void __iomem *pmerrloc_base; + void __iomem *pmecc_rom_base; + + /* lookup table for alpha_to and index_of */ + void __iomem *pmecc_alpha_to; + void __iomem *pmecc_index_of; + + /* data for pmecc computation */ + int16_t *pmecc_partial_syn; + int16_t *pmecc_si; + int16_t *pmecc_smu; /* Sigma table */ + int16_t *pmecc_lmu; /* polynomal order */ + int *pmecc_mu; + int *pmecc_dmu; + int *pmecc_delta; +}; + +static struct nand_ecclayout atmel_pmecc_oobinfo; + +/* + * Enable NAND. + */ +static void atmel_nand_enable(struct atmel_nand_host *host) +{ + if (gpio_is_valid(host->board.enable_pin)) + gpio_set_value(host->board.enable_pin, 0); +} + +/* + * Disable NAND. + */ +static void atmel_nand_disable(struct atmel_nand_host *host) +{ + if (gpio_is_valid(host->board.enable_pin)) + gpio_set_value(host->board.enable_pin, 1); +} + +/* + * Hardware specific access to control-lines + */ +static void atmel_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + if (ctrl & NAND_NCE) + atmel_nand_enable(host); + else + atmel_nand_disable(host); + } + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writeb(cmd, host->io_base + (1 << host->board.cle)); + else + writeb(cmd, host->io_base + (1 << host->board.ale)); +} + +/* + * Read the Device Ready pin. + */ +static int atmel_nand_device_ready(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + return gpio_get_value(host->board.rdy_pin) ^ + !!host->board.rdy_pin_active_low; +} + +/* Set up for hardware ready pin and enable pin. */ +static int atmel_nand_set_enable_ready_pins(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + int res = 0; + + if (gpio_is_valid(host->board.rdy_pin)) { + res = devm_gpio_request(host->dev, + host->board.rdy_pin, "nand_rdy"); + if (res < 0) { + dev_err(host->dev, + "can't request rdy gpio %d\n", + host->board.rdy_pin); + return res; + } + + res = gpio_direction_input(host->board.rdy_pin); + if (res < 0) { + dev_err(host->dev, + "can't request input direction rdy gpio %d\n", + host->board.rdy_pin); + return res; + } + + chip->dev_ready = atmel_nand_device_ready; + } + + if (gpio_is_valid(host->board.enable_pin)) { + res = devm_gpio_request(host->dev, + host->board.enable_pin, "nand_enable"); + if (res < 0) { + dev_err(host->dev, + "can't request enable gpio %d\n", + host->board.enable_pin); + return res; + } + + res = gpio_direction_output(host->board.enable_pin, 1); + if (res < 0) { + dev_err(host->dev, + "can't request output direction enable gpio %d\n", + host->board.enable_pin); + return res; + } + } + + return res; +} + +/* + * Minimal-overhead PIO for data access. + */ +static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + if (host->nfc && host->nfc->use_nfc_sram && host->nfc->data_in_sram) { + memcpy(buf, host->nfc->data_in_sram, len); + host->nfc->data_in_sram += len; + } else { + __raw_readsb(nand_chip->IO_ADDR_R, buf, len); + } +} + +static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + if (host->nfc && host->nfc->use_nfc_sram && host->nfc->data_in_sram) { + memcpy(buf, host->nfc->data_in_sram, len); + host->nfc->data_in_sram += len; + } else { + __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2); + } +} + +static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_writesb(nand_chip->IO_ADDR_W, buf, len); +} + +static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + + __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2); +} + +static void dma_complete_func(void *completion) +{ + complete(completion); +} + +static int nfc_set_sram_bank(struct atmel_nand_host *host, unsigned int bank) +{ + /* NFC only has two banks. Must be 0 or 1 */ + if (bank > 1) + return -EINVAL; + + if (bank) { + /* Only for a 2k-page or lower flash, NFC can handle 2 banks */ + if (host->mtd.writesize > 2048) + return -EINVAL; + nfc_writel(host->nfc->hsmc_regs, BANK, ATMEL_HSMC_NFC_BANK1); + } else { + nfc_writel(host->nfc->hsmc_regs, BANK, ATMEL_HSMC_NFC_BANK0); + } + + return 0; +} + +static uint nfc_get_sram_off(struct atmel_nand_host *host) +{ + if (nfc_readl(host->nfc->hsmc_regs, BANK) & ATMEL_HSMC_NFC_BANK1) + return NFC_SRAM_BANK1_OFFSET; + else + return 0; +} + +static dma_addr_t nfc_sram_phys(struct atmel_nand_host *host) +{ + if (nfc_readl(host->nfc->hsmc_regs, BANK) & ATMEL_HSMC_NFC_BANK1) + return host->nfc->sram_bank0_phys + NFC_SRAM_BANK1_OFFSET; + else + return host->nfc->sram_bank0_phys; +} + +static int atmel_nand_dma_op(struct mtd_info *mtd, void *buf, int len, + int is_read) +{ + struct dma_device *dma_dev; + enum dma_ctrl_flags flags; + dma_addr_t dma_src_addr, dma_dst_addr, phys_addr; + struct dma_async_tx_descriptor *tx = NULL; + dma_cookie_t cookie; + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + void *p = buf; + int err = -EIO; + enum dma_data_direction dir = is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE; + struct atmel_nfc *nfc = host->nfc; + + if (buf >= high_memory) + goto err_buf; + + dma_dev = host->dma_chan->device; + + flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; + + phys_addr = dma_map_single(dma_dev->dev, p, len, dir); + if (dma_mapping_error(dma_dev->dev, phys_addr)) { + dev_err(host->dev, "Failed to dma_map_single\n"); + goto err_buf; + } + + if (is_read) { + if (nfc && nfc->data_in_sram) + dma_src_addr = nfc_sram_phys(host) + (nfc->data_in_sram + - (nfc->sram_bank0 + nfc_get_sram_off(host))); + else + dma_src_addr = host->io_phys; + + dma_dst_addr = phys_addr; + } else { + dma_src_addr = phys_addr; + + if (nfc && nfc->write_by_sram) + dma_dst_addr = nfc_sram_phys(host); + else + dma_dst_addr = host->io_phys; + } + + tx = dma_dev->device_prep_dma_memcpy(host->dma_chan, dma_dst_addr, + dma_src_addr, len, flags); + if (!tx) { + dev_err(host->dev, "Failed to prepare DMA memcpy\n"); + goto err_dma; + } + + init_completion(&host->comp); + tx->callback = dma_complete_func; + tx->callback_param = &host->comp; + + cookie = tx->tx_submit(tx); + if (dma_submit_error(cookie)) { + dev_err(host->dev, "Failed to do DMA tx_submit\n"); + goto err_dma; + } + + dma_async_issue_pending(host->dma_chan); + wait_for_completion(&host->comp); + + if (is_read && nfc && nfc->data_in_sram) + /* After read data from SRAM, need to increase the position */ + nfc->data_in_sram += len; + + err = 0; + +err_dma: + dma_unmap_single(dma_dev->dev, phys_addr, len, dir); +err_buf: + if (err != 0) + dev_dbg(host->dev, "Fall back to CPU I/O\n"); + return err; +} + +static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + + if (use_dma && len > mtd->oobsize) + /* only use DMA for bigger than oob size: better performances */ + if (atmel_nand_dma_op(mtd, buf, len, 1) == 0) + return; + + if (host->board.bus_width_16) + atmel_read_buf16(mtd, buf, len); + else + atmel_read_buf8(mtd, buf, len); +} + +static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + + if (use_dma && len > mtd->oobsize) + /* only use DMA for bigger than oob size: better performances */ + if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0) + return; + + if (host->board.bus_width_16) + atmel_write_buf16(mtd, buf, len); + else + atmel_write_buf8(mtd, buf, len); +} + +/* + * Return number of ecc bytes per sector according to sector size and + * correction capability + * + * Following table shows what at91 PMECC supported: + * Correction Capability Sector_512_bytes Sector_1024_bytes + * ===================== ================ ================= + * 2-bits 4-bytes 4-bytes + * 4-bits 7-bytes 7-bytes + * 8-bits 13-bytes 14-bytes + * 12-bits 20-bytes 21-bytes + * 24-bits 39-bytes 42-bytes + */ +static int pmecc_get_ecc_bytes(int cap, int sector_size) +{ + int m = 12 + sector_size / 512; + return (m * cap + 7) / 8; +} + +static void pmecc_config_ecc_layout(struct nand_ecclayout *layout, + int oobsize, int ecc_len) +{ + int i; + + layout->eccbytes = ecc_len; + + /* ECC will occupy the last ecc_len bytes continuously */ + for (i = 0; i < ecc_len; i++) + layout->eccpos[i] = oobsize - ecc_len + i; + + layout->oobfree[0].offset = PMECC_OOB_RESERVED_BYTES; + layout->oobfree[0].length = + oobsize - ecc_len - layout->oobfree[0].offset; +} + +static void __iomem *pmecc_get_alpha_to(struct atmel_nand_host *host) +{ + int table_size; + + table_size = host->pmecc_sector_size == 512 ? + PMECC_LOOKUP_TABLE_SIZE_512 : PMECC_LOOKUP_TABLE_SIZE_1024; + + return host->pmecc_rom_base + host->pmecc_lookup_table_offset + + table_size * sizeof(int16_t); +} + +static int pmecc_data_alloc(struct atmel_nand_host *host) +{ + const int cap = host->pmecc_corr_cap; + int size; + + size = (2 * cap + 1) * sizeof(int16_t); + host->pmecc_partial_syn = devm_kzalloc(host->dev, size, GFP_KERNEL); + host->pmecc_si = devm_kzalloc(host->dev, size, GFP_KERNEL); + host->pmecc_lmu = devm_kzalloc(host->dev, + (cap + 1) * sizeof(int16_t), GFP_KERNEL); + host->pmecc_smu = devm_kzalloc(host->dev, + (cap + 2) * size, GFP_KERNEL); + + size = (cap + 1) * sizeof(int); + host->pmecc_mu = devm_kzalloc(host->dev, size, GFP_KERNEL); + host->pmecc_dmu = devm_kzalloc(host->dev, size, GFP_KERNEL); + host->pmecc_delta = devm_kzalloc(host->dev, size, GFP_KERNEL); + + if (!host->pmecc_partial_syn || + !host->pmecc_si || + !host->pmecc_lmu || + !host->pmecc_smu || + !host->pmecc_mu || + !host->pmecc_dmu || + !host->pmecc_delta) + return -ENOMEM; + + return 0; +} + +static void pmecc_gen_syndrome(struct mtd_info *mtd, int sector) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + int i; + uint32_t value; + + /* Fill odd syndromes */ + for (i = 0; i < host->pmecc_corr_cap; i++) { + value = pmecc_readl_rem_relaxed(host->ecc, sector, i / 2); + if (i & 1) + value >>= 16; + value &= 0xffff; + host->pmecc_partial_syn[(2 * i) + 1] = (int16_t)value; + } +} + +static void pmecc_substitute(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + int16_t __iomem *alpha_to = host->pmecc_alpha_to; + int16_t __iomem *index_of = host->pmecc_index_of; + int16_t *partial_syn = host->pmecc_partial_syn; + const int cap = host->pmecc_corr_cap; + int16_t *si; + int i, j; + + /* si[] is a table that holds the current syndrome value, + * an element of that table belongs to the field + */ + si = host->pmecc_si; + + memset(&si[1], 0, sizeof(int16_t) * (2 * cap - 1)); + + /* Computation 2t syndromes based on S(x) */ + /* Odd syndromes */ + for (i = 1; i < 2 * cap; i += 2) { + for (j = 0; j < host->pmecc_degree; j++) { + if (partial_syn[i] & ((unsigned short)0x1 << j)) + si[i] = readw_relaxed(alpha_to + i * j) ^ si[i]; + } + } + /* Even syndrome = (Odd syndrome) ** 2 */ + for (i = 2, j = 1; j <= cap; i = ++j << 1) { + if (si[j] == 0) { + si[i] = 0; + } else { + int16_t tmp; + + tmp = readw_relaxed(index_of + si[j]); + tmp = (tmp * 2) % host->pmecc_cw_len; + si[i] = readw_relaxed(alpha_to + tmp); + } + } + + return; +} + +static void pmecc_get_sigma(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + int16_t *lmu = host->pmecc_lmu; + int16_t *si = host->pmecc_si; + int *mu = host->pmecc_mu; + int *dmu = host->pmecc_dmu; /* Discrepancy */ + int *delta = host->pmecc_delta; /* Delta order */ + int cw_len = host->pmecc_cw_len; + const int16_t cap = host->pmecc_corr_cap; + const int num = 2 * cap + 1; + int16_t __iomem *index_of = host->pmecc_index_of; + int16_t __iomem *alpha_to = host->pmecc_alpha_to; + int i, j, k; + uint32_t dmu_0_count, tmp; + int16_t *smu = host->pmecc_smu; + + /* index of largest delta */ + int ro; + int largest; + int diff; + + dmu_0_count = 0; + + /* First Row */ + + /* Mu */ + mu[0] = -1; + + memset(smu, 0, sizeof(int16_t) * num); + smu[0] = 1; + + /* discrepancy set to 1 */ + dmu[0] = 1; + /* polynom order set to 0 */ + lmu[0] = 0; + delta[0] = (mu[0] * 2 - lmu[0]) >> 1; + + /* Second Row */ + + /* Mu */ + mu[1] = 0; + /* Sigma(x) set to 1 */ + memset(&smu[num], 0, sizeof(int16_t) * num); + smu[num] = 1; + + /* discrepancy set to S1 */ + dmu[1] = si[1]; + + /* polynom order set to 0 */ + lmu[1] = 0; + + delta[1] = (mu[1] * 2 - lmu[1]) >> 1; + + /* Init the Sigma(x) last row */ + memset(&smu[(cap + 1) * num], 0, sizeof(int16_t) * num); + + for (i = 1; i <= cap; i++) { + mu[i + 1] = i << 1; + /* Begin Computing Sigma (Mu+1) and L(mu) */ + /* check if discrepancy is set to 0 */ + if (dmu[i] == 0) { + dmu_0_count++; + + tmp = ((cap - (lmu[i] >> 1) - 1) / 2); + if ((cap - (lmu[i] >> 1) - 1) & 0x1) + tmp += 2; + else + tmp += 1; + + if (dmu_0_count == tmp) { + for (j = 0; j <= (lmu[i] >> 1) + 1; j++) + smu[(cap + 1) * num + j] = + smu[i * num + j]; + + lmu[cap + 1] = lmu[i]; + return; + } + + /* copy polynom */ + for (j = 0; j <= lmu[i] >> 1; j++) + smu[(i + 1) * num + j] = smu[i * num + j]; + + /* copy previous polynom order to the next */ + lmu[i + 1] = lmu[i]; + } else { + ro = 0; + largest = -1; + /* find largest delta with dmu != 0 */ + for (j = 0; j < i; j++) { + if ((dmu[j]) && (delta[j] > largest)) { + largest = delta[j]; + ro = j; + } + } + + /* compute difference */ + diff = (mu[i] - mu[ro]); + + /* Compute degree of the new smu polynomial */ + if ((lmu[i] >> 1) > ((lmu[ro] >> 1) + diff)) + lmu[i + 1] = lmu[i]; + else + lmu[i + 1] = ((lmu[ro] >> 1) + diff) * 2; + + /* Init smu[i+1] with 0 */ + for (k = 0; k < num; k++) + smu[(i + 1) * num + k] = 0; + + /* Compute smu[i+1] */ + for (k = 0; k <= lmu[ro] >> 1; k++) { + int16_t a, b, c; + + if (!(smu[ro * num + k] && dmu[i])) + continue; + a = readw_relaxed(index_of + dmu[i]); + b = readw_relaxed(index_of + dmu[ro]); + c = readw_relaxed(index_of + smu[ro * num + k]); + tmp = a + (cw_len - b) + c; + a = readw_relaxed(alpha_to + tmp % cw_len); + smu[(i + 1) * num + (k + diff)] = a; + } + + for (k = 0; k <= lmu[i] >> 1; k++) + smu[(i + 1) * num + k] ^= smu[i * num + k]; + } + + /* End Computing Sigma (Mu+1) and L(mu) */ + /* In either case compute delta */ + delta[i + 1] = (mu[i + 1] * 2 - lmu[i + 1]) >> 1; + + /* Do not compute discrepancy for the last iteration */ + if (i >= cap) + continue; + + for (k = 0; k <= (lmu[i + 1] >> 1); k++) { + tmp = 2 * (i - 1); + if (k == 0) { + dmu[i + 1] = si[tmp + 3]; + } else if (smu[(i + 1) * num + k] && si[tmp + 3 - k]) { + int16_t a, b, c; + a = readw_relaxed(index_of + + smu[(i + 1) * num + k]); + b = si[2 * (i - 1) + 3 - k]; + c = readw_relaxed(index_of + b); + tmp = a + c; + tmp %= cw_len; + dmu[i + 1] = readw_relaxed(alpha_to + tmp) ^ + dmu[i + 1]; + } + } + } + + return; +} + +static int pmecc_err_location(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + unsigned long end_time; + const int cap = host->pmecc_corr_cap; + const int num = 2 * cap + 1; + int sector_size = host->pmecc_sector_size; + int err_nbr = 0; /* number of error */ + int roots_nbr; /* number of roots */ + int i; + uint32_t val; + int16_t *smu = host->pmecc_smu; + + pmerrloc_writel(host->pmerrloc_base, ELDIS, PMERRLOC_DISABLE); + + for (i = 0; i <= host->pmecc_lmu[cap + 1] >> 1; i++) { + pmerrloc_writel_sigma_relaxed(host->pmerrloc_base, i, + smu[(cap + 1) * num + i]); + err_nbr++; + } + + val = (err_nbr - 1) << 16; + if (sector_size == 1024) + val |= 1; + + pmerrloc_writel(host->pmerrloc_base, ELCFG, val); + pmerrloc_writel(host->pmerrloc_base, ELEN, + sector_size * 8 + host->pmecc_degree * cap); + + end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS); + while (!(pmerrloc_readl_relaxed(host->pmerrloc_base, ELISR) + & PMERRLOC_CALC_DONE)) { + if (unlikely(time_after(jiffies, end_time))) { + dev_err(host->dev, "PMECC: Timeout to calculate error location.\n"); + return -1; + } + cpu_relax(); + } + + roots_nbr = (pmerrloc_readl_relaxed(host->pmerrloc_base, ELISR) + & PMERRLOC_ERR_NUM_MASK) >> 8; + /* Number of roots == degree of smu hence <= cap */ + if (roots_nbr == host->pmecc_lmu[cap + 1] >> 1) + return err_nbr - 1; + + /* Number of roots does not match the degree of smu + * unable to correct error */ + return -1; +} + +static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc, + int sector_num, int extra_bytes, int err_nbr) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + int i = 0; + int byte_pos, bit_pos, sector_size, pos; + uint32_t tmp; + uint8_t err_byte; + + sector_size = host->pmecc_sector_size; + + while (err_nbr) { + tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_base, i) - 1; + byte_pos = tmp / 8; + bit_pos = tmp % 8; + + if (byte_pos >= (sector_size + extra_bytes)) + BUG(); /* should never happen */ + + if (byte_pos < sector_size) { + err_byte = *(buf + byte_pos); + *(buf + byte_pos) ^= (1 << bit_pos); + + pos = sector_num * host->pmecc_sector_size + byte_pos; + dev_info(host->dev, "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + pos, bit_pos, err_byte, *(buf + byte_pos)); + } else { + /* Bit flip in OOB area */ + tmp = sector_num * nand_chip->ecc.bytes + + (byte_pos - sector_size); + err_byte = ecc[tmp]; + ecc[tmp] ^= (1 << bit_pos); + + pos = tmp + nand_chip->ecc.layout->eccpos[0]; + dev_info(host->dev, "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n", + pos, bit_pos, err_byte, ecc[tmp]); + } + + i++; + err_nbr--; + } + + return; +} + +static int pmecc_correction(struct mtd_info *mtd, u32 pmecc_stat, uint8_t *buf, + u8 *ecc) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + int i, err_nbr; + uint8_t *buf_pos; + int max_bitflips = 0; + + /* If can correct bitfilps from erased page, do the normal check */ + if (host->caps->pmecc_correct_erase_page) + goto normal_check; + + for (i = 0; i < nand_chip->ecc.total; i++) + if (ecc[i] != 0xff) + goto normal_check; + /* Erased page, return OK */ + return 0; + +normal_check: + for (i = 0; i < nand_chip->ecc.steps; i++) { + err_nbr = 0; + if (pmecc_stat & 0x1) { + buf_pos = buf + i * host->pmecc_sector_size; + + pmecc_gen_syndrome(mtd, i); + pmecc_substitute(mtd); + pmecc_get_sigma(mtd); + + err_nbr = pmecc_err_location(mtd); + if (err_nbr == -1) { + dev_err(host->dev, "PMECC: Too many errors\n"); + mtd->ecc_stats.failed++; + return -EIO; + } else { + pmecc_correct_data(mtd, buf_pos, ecc, i, + nand_chip->ecc.bytes, err_nbr); + mtd->ecc_stats.corrected += err_nbr; + max_bitflips = max_t(int, max_bitflips, err_nbr); + } + } + pmecc_stat >>= 1; + } + + return max_bitflips; +} + +static void pmecc_enable(struct atmel_nand_host *host, int ecc_op) +{ + u32 val; + + if (ecc_op != NAND_ECC_READ && ecc_op != NAND_ECC_WRITE) { + dev_err(host->dev, "atmel_nand: wrong pmecc operation type!"); + return; + } + + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_RST); + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE); + val = pmecc_readl_relaxed(host->ecc, CFG); + + if (ecc_op == NAND_ECC_READ) + pmecc_writel(host->ecc, CFG, (val & ~PMECC_CFG_WRITE_OP) + | PMECC_CFG_AUTO_ENABLE); + else + pmecc_writel(host->ecc, CFG, (val | PMECC_CFG_WRITE_OP) + & ~PMECC_CFG_AUTO_ENABLE); + + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_ENABLE); + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DATA); +} + +static int atmel_nand_pmecc_read_page(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, int page) +{ + struct atmel_nand_host *host = chip->priv; + int eccsize = chip->ecc.size * chip->ecc.steps; + uint8_t *oob = chip->oob_poi; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint32_t stat; + unsigned long end_time; + int bitflips = 0; + + if (!host->nfc || !host->nfc->use_nfc_sram) + pmecc_enable(host, NAND_ECC_READ); + + chip->read_buf(mtd, buf, eccsize); + chip->read_buf(mtd, oob, mtd->oobsize); + + end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS); + while ((pmecc_readl_relaxed(host->ecc, SR) & PMECC_SR_BUSY)) { + if (unlikely(time_after(jiffies, end_time))) { + dev_err(host->dev, "PMECC: Timeout to get error status.\n"); + return -EIO; + } + cpu_relax(); + } + + stat = pmecc_readl_relaxed(host->ecc, ISR); + if (stat != 0) { + bitflips = pmecc_correction(mtd, stat, buf, &oob[eccpos[0]]); + if (bitflips < 0) + /* uncorrectable errors */ + return 0; + } + + return bitflips; +} + +static int atmel_nand_pmecc_write_page(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + struct atmel_nand_host *host = chip->priv; + uint32_t *eccpos = chip->ecc.layout->eccpos; + int i, j; + unsigned long end_time; + + if (!host->nfc || !host->nfc->write_by_sram) { + pmecc_enable(host, NAND_ECC_WRITE); + chip->write_buf(mtd, (u8 *)buf, mtd->writesize); + } + + end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS); + while ((pmecc_readl_relaxed(host->ecc, SR) & PMECC_SR_BUSY)) { + if (unlikely(time_after(jiffies, end_time))) { + dev_err(host->dev, "PMECC: Timeout to get ECC value.\n"); + return -EIO; + } + cpu_relax(); + } + + for (i = 0; i < chip->ecc.steps; i++) { + for (j = 0; j < chip->ecc.bytes; j++) { + int pos; + + pos = i * chip->ecc.bytes + j; + chip->oob_poi[eccpos[pos]] = + pmecc_readb_ecc_relaxed(host->ecc, i, j); + } + } + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static void atmel_pmecc_core_init(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + uint32_t val = 0; + struct nand_ecclayout *ecc_layout; + + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_RST); + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE); + + switch (host->pmecc_corr_cap) { + case 2: + val = PMECC_CFG_BCH_ERR2; + break; + case 4: + val = PMECC_CFG_BCH_ERR4; + break; + case 8: + val = PMECC_CFG_BCH_ERR8; + break; + case 12: + val = PMECC_CFG_BCH_ERR12; + break; + case 24: + val = PMECC_CFG_BCH_ERR24; + break; + } + + if (host->pmecc_sector_size == 512) + val |= PMECC_CFG_SECTOR512; + else if (host->pmecc_sector_size == 1024) + val |= PMECC_CFG_SECTOR1024; + + switch (nand_chip->ecc.steps) { + case 1: + val |= PMECC_CFG_PAGE_1SECTOR; + break; + case 2: + val |= PMECC_CFG_PAGE_2SECTORS; + break; + case 4: + val |= PMECC_CFG_PAGE_4SECTORS; + break; + case 8: + val |= PMECC_CFG_PAGE_8SECTORS; + break; + } + + val |= (PMECC_CFG_READ_OP | PMECC_CFG_SPARE_DISABLE + | PMECC_CFG_AUTO_DISABLE); + pmecc_writel(host->ecc, CFG, val); + + ecc_layout = nand_chip->ecc.layout; + pmecc_writel(host->ecc, SAREA, mtd->oobsize - 1); + pmecc_writel(host->ecc, SADDR, ecc_layout->eccpos[0]); + pmecc_writel(host->ecc, EADDR, + ecc_layout->eccpos[ecc_layout->eccbytes - 1]); + /* See datasheet about PMECC Clock Control Register */ + pmecc_writel(host->ecc, CLK, 2); + pmecc_writel(host->ecc, IDR, 0xff); + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_ENABLE); +} + +/* + * Get minimum ecc requirements from NAND. + * If pmecc-cap, pmecc-sector-size in DTS are not specified, this function + * will set them according to minimum ecc requirement. Otherwise, use the + * value in DTS file. + * return 0 if success. otherwise return error code. + */ +static int pmecc_choose_ecc(struct atmel_nand_host *host, + int *cap, int *sector_size) +{ + /* Get minimum ECC requirements */ + if (host->nand_chip.ecc_strength_ds) { + *cap = host->nand_chip.ecc_strength_ds; + *sector_size = host->nand_chip.ecc_step_ds; + dev_info(host->dev, "minimum ECC: %d bits in %d bytes\n", + *cap, *sector_size); + } else { + *cap = 2; + *sector_size = 512; + dev_info(host->dev, "can't detect min. ECC, assume 2 bits in 512 bytes\n"); + } + + /* If device tree doesn't specify, use NAND's minimum ECC parameters */ + if (host->pmecc_corr_cap == 0) { + /* use the most fitable ecc bits (the near bigger one ) */ + if (*cap <= 2) + host->pmecc_corr_cap = 2; + else if (*cap <= 4) + host->pmecc_corr_cap = 4; + else if (*cap <= 8) + host->pmecc_corr_cap = 8; + else if (*cap <= 12) + host->pmecc_corr_cap = 12; + else if (*cap <= 24) + host->pmecc_corr_cap = 24; + else + return -EINVAL; + } + if (host->pmecc_sector_size == 0) { + /* use the most fitable sector size (the near smaller one ) */ + if (*sector_size >= 1024) + host->pmecc_sector_size = 1024; + else if (*sector_size >= 512) + host->pmecc_sector_size = 512; + else + return -EINVAL; + } + return 0; +} + +static inline int deg(unsigned int poly) +{ + /* polynomial degree is the most-significant bit index */ + return fls(poly) - 1; +} + +static int build_gf_tables(int mm, unsigned int poly, + int16_t *index_of, int16_t *alpha_to) +{ + unsigned int i, x = 1; + const unsigned int k = 1 << deg(poly); + unsigned int nn = (1 << mm) - 1; + + /* primitive polynomial must be of degree m */ + if (k != (1u << mm)) + return -EINVAL; + + for (i = 0; i < nn; i++) { + alpha_to[i] = x; + index_of[x] = i; + if (i && (x == 1)) + /* polynomial is not primitive (a^i=1 with 0<i<2^m-1) */ + return -EINVAL; + x <<= 1; + if (x & k) + x ^= poly; + } + alpha_to[nn] = 1; + index_of[0] = 0; + + return 0; +} + +static uint16_t *create_lookup_table(struct device *dev, int sector_size) +{ + int degree = (sector_size == 512) ? + PMECC_GF_DIMENSION_13 : + PMECC_GF_DIMENSION_14; + unsigned int poly = (sector_size == 512) ? + PMECC_GF_13_PRIMITIVE_POLY : + PMECC_GF_14_PRIMITIVE_POLY; + int table_size = (sector_size == 512) ? + PMECC_LOOKUP_TABLE_SIZE_512 : + PMECC_LOOKUP_TABLE_SIZE_1024; + + int16_t *addr = devm_kzalloc(dev, 2 * table_size * sizeof(uint16_t), + GFP_KERNEL); + if (addr && build_gf_tables(degree, poly, addr, addr + table_size)) + return NULL; + + return addr; +} + +static int atmel_pmecc_nand_init_params(struct platform_device *pdev, + struct atmel_nand_host *host) +{ + struct mtd_info *mtd = &host->mtd; + struct nand_chip *nand_chip = &host->nand_chip; + struct resource *regs, *regs_pmerr, *regs_rom; + uint16_t *galois_table; + int cap, sector_size, err_no; + + err_no = pmecc_choose_ecc(host, &cap, §or_size); + if (err_no) { + dev_err(host->dev, "The NAND flash's ECC requirement are not support!"); + return err_no; + } + + if (cap > host->pmecc_corr_cap || + sector_size != host->pmecc_sector_size) + dev_info(host->dev, "WARNING: Be Caution! Using different PMECC parameters from Nand ONFI ECC reqirement.\n"); + + cap = host->pmecc_corr_cap; + sector_size = host->pmecc_sector_size; + host->pmecc_lookup_table_offset = (sector_size == 512) ? + host->pmecc_lookup_table_offset_512 : + host->pmecc_lookup_table_offset_1024; + + dev_info(host->dev, "Initialize PMECC params, cap: %d, sector: %d\n", + cap, sector_size); + + regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!regs) { + dev_warn(host->dev, + "Can't get I/O resource regs for PMECC controller, rolling back on software ECC\n"); + nand_chip->ecc.mode = NAND_ECC_SOFT; + return 0; + } + + host->ecc = devm_ioremap_resource(&pdev->dev, regs); + if (IS_ERR(host->ecc)) { + err_no = PTR_ERR(host->ecc); + goto err; + } + + regs_pmerr = platform_get_resource(pdev, IORESOURCE_MEM, 2); + host->pmerrloc_base = devm_ioremap_resource(&pdev->dev, regs_pmerr); + if (IS_ERR(host->pmerrloc_base)) { + err_no = PTR_ERR(host->pmerrloc_base); + goto err; + } + + if (!host->has_no_lookup_table) { + regs_rom = platform_get_resource(pdev, IORESOURCE_MEM, 3); + host->pmecc_rom_base = devm_ioremap_resource(&pdev->dev, + regs_rom); + if (IS_ERR(host->pmecc_rom_base)) { + dev_err(host->dev, "Can not get I/O resource for ROM, will build a lookup table in runtime!\n"); + host->has_no_lookup_table = true; + } + } + + if (host->has_no_lookup_table) { + /* Build the look-up table in runtime */ + galois_table = create_lookup_table(host->dev, sector_size); + if (!galois_table) { + dev_err(host->dev, "Failed to build a lookup table in runtime!\n"); + err_no = -EINVAL; + goto err; + } + + host->pmecc_rom_base = (void __iomem *)galois_table; + host->pmecc_lookup_table_offset = 0; + } + + nand_chip->ecc.size = sector_size; + + /* set ECC page size and oob layout */ + switch (mtd->writesize) { + case 512: + case 1024: + case 2048: + case 4096: + case 8192: + if (sector_size > mtd->writesize) { + dev_err(host->dev, "pmecc sector size is bigger than the page size!\n"); + err_no = -EINVAL; + goto err; + } + + host->pmecc_degree = (sector_size == 512) ? + PMECC_GF_DIMENSION_13 : PMECC_GF_DIMENSION_14; + host->pmecc_cw_len = (1 << host->pmecc_degree) - 1; + host->pmecc_alpha_to = pmecc_get_alpha_to(host); + host->pmecc_index_of = host->pmecc_rom_base + + host->pmecc_lookup_table_offset; + + nand_chip->ecc.strength = cap; + nand_chip->ecc.bytes = pmecc_get_ecc_bytes(cap, sector_size); + nand_chip->ecc.steps = mtd->writesize / sector_size; + nand_chip->ecc.total = nand_chip->ecc.bytes * + nand_chip->ecc.steps; + if (nand_chip->ecc.total > + mtd->oobsize - PMECC_OOB_RESERVED_BYTES) { + dev_err(host->dev, "No room for ECC bytes\n"); + err_no = -EINVAL; + goto err; + } + pmecc_config_ecc_layout(&atmel_pmecc_oobinfo, + mtd->oobsize, + nand_chip->ecc.total); + + nand_chip->ecc.layout = &atmel_pmecc_oobinfo; + break; + default: + dev_warn(host->dev, + "Unsupported page size for PMECC, use Software ECC\n"); + /* page size not handled by HW ECC */ + /* switching back to soft ECC */ + nand_chip->ecc.mode = NAND_ECC_SOFT; + return 0; + } + + /* Allocate data for PMECC computation */ + err_no = pmecc_data_alloc(host); + if (err_no) { + dev_err(host->dev, + "Cannot allocate memory for PMECC computation!\n"); + goto err; + } + + nand_chip->options |= NAND_NO_SUBPAGE_WRITE; + nand_chip->ecc.read_page = atmel_nand_pmecc_read_page; + nand_chip->ecc.write_page = atmel_nand_pmecc_write_page; + + atmel_pmecc_core_init(mtd); + + return 0; + +err: + return err_no; +} + +/* + * Calculate HW ECC + * + * function called after a write + * + * mtd: MTD block structure + * dat: raw data (unused) + * ecc_code: buffer for ECC + */ +static int atmel_nand_calculate(struct mtd_info *mtd, + const u_char *dat, unsigned char *ecc_code) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + unsigned int ecc_value; + + /* get the first 2 ECC bytes */ + ecc_value = ecc_readl(host->ecc, PR); + + ecc_code[0] = ecc_value & 0xFF; + ecc_code[1] = (ecc_value >> 8) & 0xFF; + + /* get the last 2 ECC bytes */ + ecc_value = ecc_readl(host->ecc, NPR) & ATMEL_ECC_NPARITY; + + ecc_code[2] = ecc_value & 0xFF; + ecc_code[3] = (ecc_value >> 8) & 0xFF; + + return 0; +} + +/* + * HW ECC read page function + * + * mtd: mtd info structure + * chip: nand chip info structure + * buf: buffer to store read data + * oob_required: caller expects OOB data read to chip->oob_poi + */ +static int atmel_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + int eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint8_t *p = buf; + uint8_t *oob = chip->oob_poi; + uint8_t *ecc_pos; + int stat; + unsigned int max_bitflips = 0; + + /* + * Errata: ALE is incorrectly wired up to the ECC controller + * on the AP7000, so it will include the address cycles in the + * ECC calculation. + * + * Workaround: Reset the parity registers before reading the + * actual data. + */ + struct atmel_nand_host *host = chip->priv; + if (host->board.need_reset_workaround) + ecc_writel(host->ecc, CR, ATMEL_ECC_RST); + + /* read the page */ + chip->read_buf(mtd, p, eccsize); + + /* move to ECC position if needed */ + if (eccpos[0] != 0) { + /* This only works on large pages + * because the ECC controller waits for + * NAND_CMD_RNDOUTSTART after the + * NAND_CMD_RNDOUT. + * anyway, for small pages, the eccpos[0] == 0 + */ + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, + mtd->writesize + eccpos[0], -1); + } + + /* the ECC controller needs to read the ECC just after the data */ + ecc_pos = oob + eccpos[0]; + chip->read_buf(mtd, ecc_pos, eccbytes); + + /* check if there's an error */ + stat = chip->ecc.correct(mtd, p, oob, NULL); + + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + + /* get back to oob start (end of page) */ + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1); + + /* read the oob */ + chip->read_buf(mtd, oob, mtd->oobsize); + + return max_bitflips; +} + +/* + * HW ECC Correction + * + * function called after a read + * + * mtd: MTD block structure + * dat: raw data read from the chip + * read_ecc: ECC from the chip (unused) + * isnull: unused + * + * Detect and correct a 1 bit error for a page + */ +static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *isnull) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + unsigned int ecc_status; + unsigned int ecc_word, ecc_bit; + + /* get the status from the Status Register */ + ecc_status = ecc_readl(host->ecc, SR); + + /* if there's no error */ + if (likely(!(ecc_status & ATMEL_ECC_RECERR))) + return 0; + + /* get error bit offset (4 bits) */ + ecc_bit = ecc_readl(host->ecc, PR) & ATMEL_ECC_BITADDR; + /* get word address (12 bits) */ + ecc_word = ecc_readl(host->ecc, PR) & ATMEL_ECC_WORDADDR; + ecc_word >>= 4; + + /* if there are multiple errors */ + if (ecc_status & ATMEL_ECC_MULERR) { + /* check if it is a freshly erased block + * (filled with 0xff) */ + if ((ecc_bit == ATMEL_ECC_BITADDR) + && (ecc_word == (ATMEL_ECC_WORDADDR >> 4))) { + /* the block has just been erased, return OK */ + return 0; + } + /* it doesn't seems to be a freshly + * erased block. + * We can't correct so many errors */ + dev_dbg(host->dev, "atmel_nand : multiple errors detected." + " Unable to correct.\n"); + return -EIO; + } + + /* if there's a single bit error : we can correct it */ + if (ecc_status & ATMEL_ECC_ECCERR) { + /* there's nothing much to do here. + * the bit error is on the ECC itself. + */ + dev_dbg(host->dev, "atmel_nand : one bit error on ECC code." + " Nothing to correct\n"); + return 0; + } + + dev_dbg(host->dev, "atmel_nand : one bit error on data." + " (word offset in the page :" + " 0x%x bit offset : 0x%x)\n", + ecc_word, ecc_bit); + /* correct the error */ + if (nand_chip->options & NAND_BUSWIDTH_16) { + /* 16 bits words */ + ((unsigned short *) dat)[ecc_word] ^= (1 << ecc_bit); + } else { + /* 8 bits words */ + dat[ecc_word] ^= (1 << ecc_bit); + } + dev_dbg(host->dev, "atmel_nand : error corrected\n"); + return 1; +} + +/* + * Enable HW ECC : unused on most chips + */ +static void atmel_nand_hwctl(struct mtd_info *mtd, int mode) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + if (host->board.need_reset_workaround) + ecc_writel(host->ecc, CR, ATMEL_ECC_RST); +} + +static const struct of_device_id atmel_nand_dt_ids[]; + +static int atmel_of_init_port(struct atmel_nand_host *host, + struct device_node *np) +{ + u32 val; + u32 offset[2]; + int ecc_mode; + struct atmel_nand_data *board = &host->board; + enum of_gpio_flags flags = 0; + + host->caps = (struct atmel_nand_caps *) + of_match_device(atmel_nand_dt_ids, host->dev)->data; + + if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) { + if (val >= 32) { + dev_err(host->dev, "invalid addr-offset %u\n", val); + return -EINVAL; + } + board->ale = val; + } + + if (of_property_read_u32(np, "atmel,nand-cmd-offset", &val) == 0) { + if (val >= 32) { + dev_err(host->dev, "invalid cmd-offset %u\n", val); + return -EINVAL; + } + board->cle = val; + } + + ecc_mode = of_get_nand_ecc_mode(np); + + board->ecc_mode = ecc_mode < 0 ? NAND_ECC_SOFT : ecc_mode; + + board->on_flash_bbt = of_get_nand_on_flash_bbt(np); + + board->has_dma = of_property_read_bool(np, "atmel,nand-has-dma"); + + if (of_get_nand_bus_width(np) == 16) + board->bus_width_16 = 1; + + board->rdy_pin = of_get_gpio_flags(np, 0, &flags); + board->rdy_pin_active_low = (flags == OF_GPIO_ACTIVE_LOW); + + board->enable_pin = of_get_gpio(np, 1); + board->det_pin = of_get_gpio(np, 2); + + host->has_pmecc = of_property_read_bool(np, "atmel,has-pmecc"); + + /* load the nfc driver if there is */ + of_platform_populate(np, NULL, NULL, host->dev); + + if (!(board->ecc_mode == NAND_ECC_HW) || !host->has_pmecc) + return 0; /* Not using PMECC */ + + /* use PMECC, get correction capability, sector size and lookup + * table offset. + * If correction bits and sector size are not specified, then find + * them from NAND ONFI parameters. + */ + if (of_property_read_u32(np, "atmel,pmecc-cap", &val) == 0) { + if ((val != 2) && (val != 4) && (val != 8) && (val != 12) && + (val != 24)) { + dev_err(host->dev, + "Unsupported PMECC correction capability: %d; should be 2, 4, 8, 12 or 24\n", + val); + return -EINVAL; + } + host->pmecc_corr_cap = (u8)val; + } + + if (of_property_read_u32(np, "atmel,pmecc-sector-size", &val) == 0) { + if ((val != 512) && (val != 1024)) { + dev_err(host->dev, + "Unsupported PMECC sector size: %d; should be 512 or 1024 bytes\n", + val); + return -EINVAL; + } + host->pmecc_sector_size = (u16)val; + } + + if (of_property_read_u32_array(np, "atmel,pmecc-lookup-table-offset", + offset, 2) != 0) { + dev_err(host->dev, "Cannot get PMECC lookup table offset, will build a lookup table in runtime.\n"); + host->has_no_lookup_table = true; + /* Will build a lookup table and initialize the offset later */ + return 0; + } + if (!offset[0] && !offset[1]) { + dev_err(host->dev, "Invalid PMECC lookup table offset\n"); + return -EINVAL; + } + host->pmecc_lookup_table_offset_512 = offset[0]; + host->pmecc_lookup_table_offset_1024 = offset[1]; + + return 0; +} + +static int atmel_hw_nand_init_params(struct platform_device *pdev, + struct atmel_nand_host *host) +{ + struct mtd_info *mtd = &host->mtd; + struct nand_chip *nand_chip = &host->nand_chip; + struct resource *regs; + + regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!regs) { + dev_err(host->dev, + "Can't get I/O resource regs, use software ECC\n"); + nand_chip->ecc.mode = NAND_ECC_SOFT; + return 0; + } + + host->ecc = devm_ioremap_resource(&pdev->dev, regs); + if (IS_ERR(host->ecc)) + return PTR_ERR(host->ecc); + + /* ECC is calculated for the whole page (1 step) */ + nand_chip->ecc.size = mtd->writesize; + + /* set ECC page size and oob layout */ + switch (mtd->writesize) { + case 512: + nand_chip->ecc.layout = &atmel_oobinfo_small; + ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_528); + break; + case 1024: + nand_chip->ecc.layout = &atmel_oobinfo_large; + ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_1056); + break; + case 2048: + nand_chip->ecc.layout = &atmel_oobinfo_large; + ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_2112); + break; + case 4096: + nand_chip->ecc.layout = &atmel_oobinfo_large; + ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_4224); + break; + default: + /* page size not handled by HW ECC */ + /* switching back to soft ECC */ + nand_chip->ecc.mode = NAND_ECC_SOFT; + return 0; + } + + /* set up for HW ECC */ + nand_chip->ecc.calculate = atmel_nand_calculate; + nand_chip->ecc.correct = atmel_nand_correct; + nand_chip->ecc.hwctl = atmel_nand_hwctl; + nand_chip->ecc.read_page = atmel_nand_read_page; + nand_chip->ecc.bytes = 4; + nand_chip->ecc.strength = 1; + + return 0; +} + +static inline u32 nfc_read_status(struct atmel_nand_host *host) +{ + u32 err_flags = NFC_SR_DTOE | NFC_SR_UNDEF | NFC_SR_AWB | NFC_SR_ASE; + u32 nfc_status = nfc_readl(host->nfc->hsmc_regs, SR); + + if (unlikely(nfc_status & err_flags)) { + if (nfc_status & NFC_SR_DTOE) + dev_err(host->dev, "NFC: Waiting Nand R/B Timeout Error\n"); + else if (nfc_status & NFC_SR_UNDEF) + dev_err(host->dev, "NFC: Access Undefined Area Error\n"); + else if (nfc_status & NFC_SR_AWB) + dev_err(host->dev, "NFC: Access memory While NFC is busy\n"); + else if (nfc_status & NFC_SR_ASE) + dev_err(host->dev, "NFC: Access memory Size Error\n"); + } + + return nfc_status; +} + +/* SMC interrupt service routine */ +static irqreturn_t hsmc_interrupt(int irq, void *dev_id) +{ + struct atmel_nand_host *host = dev_id; + u32 status, mask, pending; + irqreturn_t ret = IRQ_NONE; + + status = nfc_read_status(host); + mask = nfc_readl(host->nfc->hsmc_regs, IMR); + pending = status & mask; + + if (pending & NFC_SR_XFR_DONE) { + complete(&host->nfc->comp_xfer_done); + nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_XFR_DONE); + ret = IRQ_HANDLED; + } + if (pending & NFC_SR_RB_EDGE) { + complete(&host->nfc->comp_ready); + nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_RB_EDGE); + ret = IRQ_HANDLED; + } + if (pending & NFC_SR_CMD_DONE) { + complete(&host->nfc->comp_cmd_done); + nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_CMD_DONE); + ret = IRQ_HANDLED; + } + + return ret; +} + +/* NFC(Nand Flash Controller) related functions */ +static void nfc_prepare_interrupt(struct atmel_nand_host *host, u32 flag) +{ + if (flag & NFC_SR_XFR_DONE) + init_completion(&host->nfc->comp_xfer_done); + + if (flag & NFC_SR_RB_EDGE) + init_completion(&host->nfc->comp_ready); + + if (flag & NFC_SR_CMD_DONE) + init_completion(&host->nfc->comp_cmd_done); + + /* Enable interrupt that need to wait for */ + nfc_writel(host->nfc->hsmc_regs, IER, flag); +} + +static int nfc_wait_interrupt(struct atmel_nand_host *host, u32 flag) +{ + int i, index = 0; + struct completion *comp[3]; /* Support 3 interrupt completion */ + + if (flag & NFC_SR_XFR_DONE) + comp[index++] = &host->nfc->comp_xfer_done; + + if (flag & NFC_SR_RB_EDGE) + comp[index++] = &host->nfc->comp_ready; + + if (flag & NFC_SR_CMD_DONE) + comp[index++] = &host->nfc->comp_cmd_done; + + if (index == 0) { + dev_err(host->dev, "Unknown interrupt flag: 0x%08x\n", flag); + return -EINVAL; + } + + for (i = 0; i < index; i++) { + if (wait_for_completion_timeout(comp[i], + msecs_to_jiffies(NFC_TIME_OUT_MS))) + continue; /* wait for next completion */ + else + goto err_timeout; + } + + return 0; + +err_timeout: + dev_err(host->dev, "Time out to wait for interrupt: 0x%08x\n", flag); + /* Disable the interrupt as it is not handled by interrupt handler */ + nfc_writel(host->nfc->hsmc_regs, IDR, flag); + return -ETIMEDOUT; +} + +static int nfc_send_command(struct atmel_nand_host *host, + unsigned int cmd, unsigned int addr, unsigned char cycle0) +{ + unsigned long timeout; + u32 flag = NFC_SR_CMD_DONE; + flag |= cmd & NFCADDR_CMD_DATAEN ? NFC_SR_XFR_DONE : 0; + + dev_dbg(host->dev, + "nfc_cmd: 0x%08x, addr1234: 0x%08x, cycle0: 0x%02x\n", + cmd, addr, cycle0); + + timeout = jiffies + msecs_to_jiffies(NFC_TIME_OUT_MS); + while (nfc_readl(host->nfc->hsmc_regs, SR) & NFC_SR_BUSY) { + if (time_after(jiffies, timeout)) { + dev_err(host->dev, + "Time out to wait for NFC ready!\n"); + return -ETIMEDOUT; + } + } + + nfc_prepare_interrupt(host, flag); + nfc_writel(host->nfc->hsmc_regs, CYCLE0, cycle0); + nfc_cmd_addr1234_writel(cmd, addr, host->nfc->base_cmd_regs); + return nfc_wait_interrupt(host, flag); +} + +static int nfc_device_ready(struct mtd_info *mtd) +{ + u32 status, mask; + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + status = nfc_read_status(host); + mask = nfc_readl(host->nfc->hsmc_regs, IMR); + + /* The mask should be 0. If not we may lost interrupts */ + if (unlikely(mask & status)) + dev_err(host->dev, "Lost the interrupt flags: 0x%08x\n", + mask & status); + + return status & NFC_SR_RB_EDGE; +} + +static void nfc_select_chip(struct mtd_info *mtd, int chip) +{ + struct nand_chip *nand_chip = mtd->priv; + struct atmel_nand_host *host = nand_chip->priv; + + if (chip == -1) + nfc_writel(host->nfc->hsmc_regs, CTRL, NFC_CTRL_DISABLE); + else + nfc_writel(host->nfc->hsmc_regs, CTRL, NFC_CTRL_ENABLE); +} + +static int nfc_make_addr(struct mtd_info *mtd, int command, int column, + int page_addr, unsigned int *addr1234, unsigned int *cycle0) +{ + struct nand_chip *chip = mtd->priv; + + int acycle = 0; + unsigned char addr_bytes[8]; + int index = 0, bit_shift; + + BUG_ON(addr1234 == NULL || cycle0 == NULL); + + *cycle0 = 0; + *addr1234 = 0; + + if (column != -1) { + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + addr_bytes[acycle++] = column & 0xff; + if (mtd->writesize > 512) + addr_bytes[acycle++] = (column >> 8) & 0xff; + } + + if (page_addr != -1) { + addr_bytes[acycle++] = page_addr & 0xff; + addr_bytes[acycle++] = (page_addr >> 8) & 0xff; + if (chip->chipsize > (128 << 20)) + addr_bytes[acycle++] = (page_addr >> 16) & 0xff; + } + + if (acycle > 4) + *cycle0 = addr_bytes[index++]; + + for (bit_shift = 0; index < acycle; bit_shift += 8) + *addr1234 += addr_bytes[index++] << bit_shift; + + /* return acycle in cmd register */ + return acycle << NFCADDR_CMD_ACYCLE_BIT_POS; +} + +static void nfc_nand_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + unsigned long timeout; + unsigned int nfc_addr_cmd = 0; + + unsigned int cmd1 = command << NFCADDR_CMD_CMD1_BIT_POS; + + /* Set default settings: no cmd2, no addr cycle. read from nand */ + unsigned int cmd2 = 0; + unsigned int vcmd2 = 0; + int acycle = NFCADDR_CMD_ACYCLE_NONE; + int csid = NFCADDR_CMD_CSID_3; + int dataen = NFCADDR_CMD_DATADIS; + int nfcwr = NFCADDR_CMD_NFCRD; + unsigned int addr1234 = 0; + unsigned int cycle0 = 0; + bool do_addr = true; + host->nfc->data_in_sram = NULL; + + dev_dbg(host->dev, "%s: cmd = 0x%02x, col = 0x%08x, page = 0x%08x\n", + __func__, command, column, page_addr); + + switch (command) { + case NAND_CMD_RESET: + nfc_addr_cmd = cmd1 | acycle | csid | dataen | nfcwr; + nfc_send_command(host, nfc_addr_cmd, addr1234, cycle0); + udelay(chip->chip_delay); + + nfc_nand_command(mtd, NAND_CMD_STATUS, -1, -1); + timeout = jiffies + msecs_to_jiffies(NFC_TIME_OUT_MS); + while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) { + if (time_after(jiffies, timeout)) { + dev_err(host->dev, + "Time out to wait status ready!\n"); + break; + } + } + return; + case NAND_CMD_STATUS: + do_addr = false; + break; + case NAND_CMD_PARAM: + case NAND_CMD_READID: + do_addr = false; + acycle = NFCADDR_CMD_ACYCLE_1; + if (column != -1) + addr1234 = column; + break; + case NAND_CMD_RNDOUT: + cmd2 = NAND_CMD_RNDOUTSTART << NFCADDR_CMD_CMD2_BIT_POS; + vcmd2 = NFCADDR_CMD_VCMD2; + break; + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + if (command == NAND_CMD_READOOB) { + column += mtd->writesize; + command = NAND_CMD_READ0; /* only READ0 is valid */ + cmd1 = command << NFCADDR_CMD_CMD1_BIT_POS; + } + if (host->nfc->use_nfc_sram) { + /* Enable Data transfer to sram */ + dataen = NFCADDR_CMD_DATAEN; + + /* Need enable PMECC now, since NFC will transfer + * data in bus after sending nfc read command. + */ + if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) + pmecc_enable(host, NAND_ECC_READ); + } + + cmd2 = NAND_CMD_READSTART << NFCADDR_CMD_CMD2_BIT_POS; + vcmd2 = NFCADDR_CMD_VCMD2; + break; + /* For prgramming command, the cmd need set to write enable */ + case NAND_CMD_PAGEPROG: + case NAND_CMD_SEQIN: + case NAND_CMD_RNDIN: + nfcwr = NFCADDR_CMD_NFCWR; + if (host->nfc->will_write_sram && command == NAND_CMD_SEQIN) + dataen = NFCADDR_CMD_DATAEN; + break; + default: + break; + } + + if (do_addr) + acycle = nfc_make_addr(mtd, command, column, page_addr, + &addr1234, &cycle0); + + nfc_addr_cmd = cmd1 | cmd2 | vcmd2 | acycle | csid | dataen | nfcwr; + nfc_send_command(host, nfc_addr_cmd, addr1234, cycle0); + + /* + * Program and erase have their own busy handlers status, sequential + * in, and deplete1 need no delay. + */ + switch (command) { + case NAND_CMD_CACHEDPROG: + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_RNDIN: + case NAND_CMD_STATUS: + case NAND_CMD_RNDOUT: + case NAND_CMD_SEQIN: + case NAND_CMD_READID: + return; + + case NAND_CMD_READ0: + if (dataen == NFCADDR_CMD_DATAEN) { + host->nfc->data_in_sram = host->nfc->sram_bank0 + + nfc_get_sram_off(host); + return; + } + /* fall through */ + default: + nfc_prepare_interrupt(host, NFC_SR_RB_EDGE); + nfc_wait_interrupt(host, NFC_SR_RB_EDGE); + } +} + +static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, int data_len, const uint8_t *buf, + int oob_required, int page, int cached, int raw) +{ + int cfg, len; + int status = 0; + struct atmel_nand_host *host = chip->priv; + void *sram = host->nfc->sram_bank0 + nfc_get_sram_off(host); + + /* Subpage write is not supported */ + if (offset || (data_len < mtd->writesize)) + return -EINVAL; + + len = mtd->writesize; + /* Copy page data to sram that will write to nand via NFC */ + if (use_dma) { + if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) != 0) + /* Fall back to use cpu copy */ + memcpy(sram, buf, len); + } else { + memcpy(sram, buf, len); + } + + cfg = nfc_readl(host->nfc->hsmc_regs, CFG); + if (unlikely(raw) && oob_required) { + memcpy(sram + len, chip->oob_poi, mtd->oobsize); + len += mtd->oobsize; + nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); + } else { + nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); + } + + if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) + /* + * When use NFC sram, need set up PMECC before send + * NAND_CMD_SEQIN command. Since when the nand command + * is sent, nfc will do transfer from sram and nand. + */ + pmecc_enable(host, NAND_ECC_WRITE); + + host->nfc->will_write_sram = true; + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + host->nfc->will_write_sram = false; + + if (likely(!raw)) + /* Need to write ecc into oob */ + status = chip->ecc.write_page(mtd, chip, buf, oob_required); + + if (status < 0) + return status; + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + + if ((status & NAND_STATUS_FAIL) && (chip->errstat)) + status = chip->errstat(mtd, chip, FL_WRITING, status, page); + + if (status & NAND_STATUS_FAIL) + return -EIO; + + return 0; +} + +static int nfc_sram_init(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct atmel_nand_host *host = chip->priv; + int res = 0; + + /* Initialize the NFC CFG register */ + unsigned int cfg_nfc = 0; + + /* set page size and oob layout */ + switch (mtd->writesize) { + case 512: + cfg_nfc = NFC_CFG_PAGESIZE_512; + break; + case 1024: + cfg_nfc = NFC_CFG_PAGESIZE_1024; + break; + case 2048: + cfg_nfc = NFC_CFG_PAGESIZE_2048; + break; + case 4096: + cfg_nfc = NFC_CFG_PAGESIZE_4096; + break; + case 8192: + cfg_nfc = NFC_CFG_PAGESIZE_8192; + break; + default: + dev_err(host->dev, "Unsupported page size for NFC.\n"); + res = -ENXIO; + return res; + } + + /* oob bytes size = (NFCSPARESIZE + 1) * 4 + * Max support spare size is 512 bytes. */ + cfg_nfc |= (((mtd->oobsize / 4) - 1) << NFC_CFG_NFC_SPARESIZE_BIT_POS + & NFC_CFG_NFC_SPARESIZE); + /* default set a max timeout */ + cfg_nfc |= NFC_CFG_RSPARE | + NFC_CFG_NFC_DTOCYC | NFC_CFG_NFC_DTOMUL; + + nfc_writel(host->nfc->hsmc_regs, CFG, cfg_nfc); + + host->nfc->will_write_sram = false; + nfc_set_sram_bank(host, 0); + + /* Use Write page with NFC SRAM only for PMECC or ECC NONE. */ + if (host->nfc->write_by_sram) { + if ((chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) || + chip->ecc.mode == NAND_ECC_NONE) + chip->write_page = nfc_sram_write_page; + else + host->nfc->write_by_sram = false; + } + + dev_info(host->dev, "Using NFC Sram read %s\n", + host->nfc->write_by_sram ? "and write" : ""); + return 0; +} + +static struct platform_driver atmel_nand_nfc_driver; +/* + * Probe for the NAND device. + */ +static int atmel_nand_probe(struct platform_device *pdev) +{ + struct atmel_nand_host *host; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + struct resource *mem; + struct mtd_part_parser_data ppdata = {}; + int res, irq; + + /* Allocate memory for the device structure (and zero it) */ + host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + + res = platform_driver_register(&atmel_nand_nfc_driver); + if (res) + dev_err(&pdev->dev, "atmel_nand: can't register NFC driver\n"); + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->io_base = devm_ioremap_resource(&pdev->dev, mem); + if (IS_ERR(host->io_base)) { + res = PTR_ERR(host->io_base); + goto err_nand_ioremap; + } + host->io_phys = (dma_addr_t)mem->start; + + mtd = &host->mtd; + nand_chip = &host->nand_chip; + host->dev = &pdev->dev; + if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) { + /* Only when CONFIG_OF is enabled of_node can be parsed */ + res = atmel_of_init_port(host, pdev->dev.of_node); + if (res) + goto err_nand_ioremap; + } else { + memcpy(&host->board, dev_get_platdata(&pdev->dev), + sizeof(struct atmel_nand_data)); + } + + nand_chip->priv = host; /* link the private data structures */ + mtd->priv = nand_chip; + mtd->owner = THIS_MODULE; + + /* Set address of NAND IO lines */ + nand_chip->IO_ADDR_R = host->io_base; + nand_chip->IO_ADDR_W = host->io_base; + + if (nand_nfc.is_initialized) { + /* NFC driver is probed and initialized */ + host->nfc = &nand_nfc; + + nand_chip->select_chip = nfc_select_chip; + nand_chip->dev_ready = nfc_device_ready; + nand_chip->cmdfunc = nfc_nand_command; + + /* Initialize the interrupt for NFC */ + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(host->dev, "Cannot get HSMC irq!\n"); + res = irq; + goto err_nand_ioremap; + } + + res = devm_request_irq(&pdev->dev, irq, hsmc_interrupt, + 0, "hsmc", host); + if (res) { + dev_err(&pdev->dev, "Unable to request HSMC irq %d\n", + irq); + goto err_nand_ioremap; + } + } else { + res = atmel_nand_set_enable_ready_pins(mtd); + if (res) + goto err_nand_ioremap; + + nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl; + } + + nand_chip->ecc.mode = host->board.ecc_mode; + nand_chip->chip_delay = 40; /* 40us command delay time */ + + if (host->board.bus_width_16) /* 16-bit bus width */ + nand_chip->options |= NAND_BUSWIDTH_16; + + nand_chip->read_buf = atmel_read_buf; + nand_chip->write_buf = atmel_write_buf; + + platform_set_drvdata(pdev, host); + atmel_nand_enable(host); + + if (gpio_is_valid(host->board.det_pin)) { + res = devm_gpio_request(&pdev->dev, + host->board.det_pin, "nand_det"); + if (res < 0) { + dev_err(&pdev->dev, + "can't request det gpio %d\n", + host->board.det_pin); + goto err_no_card; + } + + res = gpio_direction_input(host->board.det_pin); + if (res < 0) { + dev_err(&pdev->dev, + "can't request input direction det gpio %d\n", + host->board.det_pin); + goto err_no_card; + } + + if (gpio_get_value(host->board.det_pin)) { + dev_info(&pdev->dev, "No SmartMedia card inserted.\n"); + res = -ENXIO; + goto err_no_card; + } + } + + if (host->board.on_flash_bbt || on_flash_bbt) { + dev_info(&pdev->dev, "Use On Flash BBT\n"); + nand_chip->bbt_options |= NAND_BBT_USE_FLASH; + } + + if (!host->board.has_dma) + use_dma = 0; + + if (use_dma) { + dma_cap_mask_t mask; + + dma_cap_zero(mask); + dma_cap_set(DMA_MEMCPY, mask); + host->dma_chan = dma_request_channel(mask, NULL, NULL); + if (!host->dma_chan) { + dev_err(host->dev, "Failed to request DMA channel\n"); + use_dma = 0; + } + } + if (use_dma) + dev_info(host->dev, "Using %s for DMA transfers.\n", + dma_chan_name(host->dma_chan)); + else + dev_info(host->dev, "No DMA support for NAND access.\n"); + + /* first scan to find the device and get the page size */ + if (nand_scan_ident(mtd, 1, NULL)) { + res = -ENXIO; + goto err_scan_ident; + } + + if (nand_chip->ecc.mode == NAND_ECC_HW) { + if (host->has_pmecc) + res = atmel_pmecc_nand_init_params(pdev, host); + else + res = atmel_hw_nand_init_params(pdev, host); + + if (res != 0) + goto err_hw_ecc; + } + + /* initialize the nfc configuration register */ + if (host->nfc && host->nfc->use_nfc_sram) { + res = nfc_sram_init(mtd); + if (res) { + host->nfc->use_nfc_sram = false; + dev_err(host->dev, "Disable use nfc sram for data transfer.\n"); + } + } + + /* second phase scan */ + if (nand_scan_tail(mtd)) { + res = -ENXIO; + goto err_scan_tail; + } + + mtd->name = "atmel_nand"; + ppdata.of_node = pdev->dev.of_node; + res = mtd_device_parse_register(mtd, NULL, &ppdata, + host->board.parts, host->board.num_parts); + if (!res) + return res; + +err_scan_tail: + if (host->has_pmecc && host->nand_chip.ecc.mode == NAND_ECC_HW) + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE); +err_hw_ecc: +err_scan_ident: +err_no_card: + atmel_nand_disable(host); + if (host->dma_chan) + dma_release_channel(host->dma_chan); +err_nand_ioremap: + return res; +} + +/* + * Remove a NAND device. + */ +static int atmel_nand_remove(struct platform_device *pdev) +{ + struct atmel_nand_host *host = platform_get_drvdata(pdev); + struct mtd_info *mtd = &host->mtd; + + nand_release(mtd); + + atmel_nand_disable(host); + + if (host->has_pmecc && host->nand_chip.ecc.mode == NAND_ECC_HW) { + pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE); + pmerrloc_writel(host->pmerrloc_base, ELDIS, + PMERRLOC_DISABLE); + } + + if (host->dma_chan) + dma_release_channel(host->dma_chan); + + platform_driver_unregister(&atmel_nand_nfc_driver); + + return 0; +} + +static struct atmel_nand_caps at91rm9200_caps = { + .pmecc_correct_erase_page = false, +}; + +static struct atmel_nand_caps sama5d4_caps = { + .pmecc_correct_erase_page = true, +}; + +static const struct of_device_id atmel_nand_dt_ids[] = { + { .compatible = "atmel,at91rm9200-nand", .data = &at91rm9200_caps }, + { .compatible = "atmel,sama5d4-nand", .data = &sama5d4_caps }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, atmel_nand_dt_ids); + +static int atmel_nand_nfc_probe(struct platform_device *pdev) +{ + struct atmel_nfc *nfc = &nand_nfc; + struct resource *nfc_cmd_regs, *nfc_hsmc_regs, *nfc_sram; + int ret; + + nfc_cmd_regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nfc->base_cmd_regs = devm_ioremap_resource(&pdev->dev, nfc_cmd_regs); + if (IS_ERR(nfc->base_cmd_regs)) + return PTR_ERR(nfc->base_cmd_regs); + + nfc_hsmc_regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); + nfc->hsmc_regs = devm_ioremap_resource(&pdev->dev, nfc_hsmc_regs); + if (IS_ERR(nfc->hsmc_regs)) + return PTR_ERR(nfc->hsmc_regs); + + nfc_sram = platform_get_resource(pdev, IORESOURCE_MEM, 2); + if (nfc_sram) { + nfc->sram_bank0 = (void * __force) + devm_ioremap_resource(&pdev->dev, nfc_sram); + if (IS_ERR(nfc->sram_bank0)) { + dev_warn(&pdev->dev, "Fail to ioremap the NFC sram with error: %ld. So disable NFC sram.\n", + PTR_ERR(nfc->sram_bank0)); + } else { + nfc->use_nfc_sram = true; + nfc->sram_bank0_phys = (dma_addr_t)nfc_sram->start; + + if (pdev->dev.of_node) + nfc->write_by_sram = of_property_read_bool( + pdev->dev.of_node, + "atmel,write-by-sram"); + } + } + + nfc_writel(nfc->hsmc_regs, IDR, 0xffffffff); + nfc_readl(nfc->hsmc_regs, SR); /* clear the NFC_SR */ + + nfc->clk = devm_clk_get(&pdev->dev, NULL); + if (!IS_ERR(nfc->clk)) { + ret = clk_prepare_enable(nfc->clk); + if (ret) + return ret; + } else { + dev_warn(&pdev->dev, "NFC clock missing, update your Device Tree"); + } + + nfc->is_initialized = true; + dev_info(&pdev->dev, "NFC is probed.\n"); + + return 0; +} + +static int atmel_nand_nfc_remove(struct platform_device *pdev) +{ + struct atmel_nfc *nfc = &nand_nfc; + + if (!IS_ERR(nfc->clk)) + clk_disable_unprepare(nfc->clk); + + return 0; +} + +static const struct of_device_id atmel_nand_nfc_match[] = { + { .compatible = "atmel,sama5d3-nfc" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, atmel_nand_nfc_match); + +static struct platform_driver atmel_nand_nfc_driver = { + .driver = { + .name = "atmel_nand_nfc", + .of_match_table = of_match_ptr(atmel_nand_nfc_match), + }, + .probe = atmel_nand_nfc_probe, + .remove = atmel_nand_nfc_remove, +}; + +static struct platform_driver atmel_nand_driver = { + .probe = atmel_nand_probe, + .remove = atmel_nand_remove, + .driver = { + .name = "atmel_nand", + .of_match_table = of_match_ptr(atmel_nand_dt_ids), + }, +}; + +module_platform_driver(atmel_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Rick Bronson"); +MODULE_DESCRIPTION("NAND/SmartMedia driver for AT91 / AVR32"); +MODULE_ALIAS("platform:atmel_nand"); diff --git a/drivers/mtd/nand/atmel_nand_ecc.h b/drivers/mtd/nand/atmel_nand_ecc.h new file mode 100644 index 000000000..668e7358f --- /dev/null +++ b/drivers/mtd/nand/atmel_nand_ecc.h @@ -0,0 +1,158 @@ +/* + * Error Corrected Code Controller (ECC) - System peripherals regsters. + * Based on AT91SAM9260 datasheet revision B. + * + * Copyright (C) 2007 Andrew Victor + * Copyright (C) 2007 - 2012 Atmel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef ATMEL_NAND_ECC_H +#define ATMEL_NAND_ECC_H + +#define ATMEL_ECC_CR 0x00 /* Control register */ +#define ATMEL_ECC_RST (1 << 0) /* Reset parity */ + +#define ATMEL_ECC_MR 0x04 /* Mode register */ +#define ATMEL_ECC_PAGESIZE (3 << 0) /* Page Size */ +#define ATMEL_ECC_PAGESIZE_528 (0) +#define ATMEL_ECC_PAGESIZE_1056 (1) +#define ATMEL_ECC_PAGESIZE_2112 (2) +#define ATMEL_ECC_PAGESIZE_4224 (3) + +#define ATMEL_ECC_SR 0x08 /* Status register */ +#define ATMEL_ECC_RECERR (1 << 0) /* Recoverable Error */ +#define ATMEL_ECC_ECCERR (1 << 1) /* ECC Single Bit Error */ +#define ATMEL_ECC_MULERR (1 << 2) /* Multiple Errors */ + +#define ATMEL_ECC_PR 0x0c /* Parity register */ +#define ATMEL_ECC_BITADDR (0xf << 0) /* Bit Error Address */ +#define ATMEL_ECC_WORDADDR (0xfff << 4) /* Word Error Address */ + +#define ATMEL_ECC_NPR 0x10 /* NParity register */ +#define ATMEL_ECC_NPARITY (0xffff << 0) /* NParity */ + +/* PMECC Register Definitions */ +#define ATMEL_PMECC_CFG 0x000 /* Configuration Register */ +#define PMECC_CFG_BCH_ERR2 (0 << 0) +#define PMECC_CFG_BCH_ERR4 (1 << 0) +#define PMECC_CFG_BCH_ERR8 (2 << 0) +#define PMECC_CFG_BCH_ERR12 (3 << 0) +#define PMECC_CFG_BCH_ERR24 (4 << 0) + +#define PMECC_CFG_SECTOR512 (0 << 4) +#define PMECC_CFG_SECTOR1024 (1 << 4) + +#define PMECC_CFG_PAGE_1SECTOR (0 << 8) +#define PMECC_CFG_PAGE_2SECTORS (1 << 8) +#define PMECC_CFG_PAGE_4SECTORS (2 << 8) +#define PMECC_CFG_PAGE_8SECTORS (3 << 8) + +#define PMECC_CFG_READ_OP (0 << 12) +#define PMECC_CFG_WRITE_OP (1 << 12) + +#define PMECC_CFG_SPARE_ENABLE (1 << 16) +#define PMECC_CFG_SPARE_DISABLE (0 << 16) + +#define PMECC_CFG_AUTO_ENABLE (1 << 20) +#define PMECC_CFG_AUTO_DISABLE (0 << 20) + +#define ATMEL_PMECC_SAREA 0x004 /* Spare area size */ +#define ATMEL_PMECC_SADDR 0x008 /* PMECC starting address */ +#define ATMEL_PMECC_EADDR 0x00c /* PMECC ending address */ +#define ATMEL_PMECC_CLK 0x010 /* PMECC clock control */ +#define PMECC_CLK_133MHZ (2 << 0) + +#define ATMEL_PMECC_CTRL 0x014 /* PMECC control register */ +#define PMECC_CTRL_RST (1 << 0) +#define PMECC_CTRL_DATA (1 << 1) +#define PMECC_CTRL_USER (1 << 2) +#define PMECC_CTRL_ENABLE (1 << 4) +#define PMECC_CTRL_DISABLE (1 << 5) + +#define ATMEL_PMECC_SR 0x018 /* PMECC status register */ +#define PMECC_SR_BUSY (1 << 0) +#define PMECC_SR_ENABLE (1 << 4) + +#define ATMEL_PMECC_IER 0x01c /* PMECC interrupt enable */ +#define PMECC_IER_ENABLE (1 << 0) +#define ATMEL_PMECC_IDR 0x020 /* PMECC interrupt disable */ +#define PMECC_IER_DISABLE (1 << 0) +#define ATMEL_PMECC_IMR 0x024 /* PMECC interrupt mask */ +#define PMECC_IER_MASK (1 << 0) +#define ATMEL_PMECC_ISR 0x028 /* PMECC interrupt status */ +#define ATMEL_PMECC_ECCx 0x040 /* PMECC ECC x */ +#define ATMEL_PMECC_REMx 0x240 /* PMECC REM x */ + +/* PMERRLOC Register Definitions */ +#define ATMEL_PMERRLOC_ELCFG 0x000 /* Error location config */ +#define PMERRLOC_ELCFG_SECTOR_512 (0 << 0) +#define PMERRLOC_ELCFG_SECTOR_1024 (1 << 0) +#define PMERRLOC_ELCFG_NUM_ERRORS(n) ((n) << 16) + +#define ATMEL_PMERRLOC_ELPRIM 0x004 /* Error location primitive */ +#define ATMEL_PMERRLOC_ELEN 0x008 /* Error location enable */ +#define ATMEL_PMERRLOC_ELDIS 0x00c /* Error location disable */ +#define PMERRLOC_DISABLE (1 << 0) + +#define ATMEL_PMERRLOC_ELSR 0x010 /* Error location status */ +#define PMERRLOC_ELSR_BUSY (1 << 0) +#define ATMEL_PMERRLOC_ELIER 0x014 /* Error location int enable */ +#define ATMEL_PMERRLOC_ELIDR 0x018 /* Error location int disable */ +#define ATMEL_PMERRLOC_ELIMR 0x01c /* Error location int mask */ +#define ATMEL_PMERRLOC_ELISR 0x020 /* Error location int status */ +#define PMERRLOC_ERR_NUM_MASK (0x1f << 8) +#define PMERRLOC_CALC_DONE (1 << 0) +#define ATMEL_PMERRLOC_SIGMAx 0x028 /* Error location SIGMA x */ +#define ATMEL_PMERRLOC_ELx 0x08c /* Error location x */ + +/* Register access macros for PMECC */ +#define pmecc_readl_relaxed(addr, reg) \ + readl_relaxed((addr) + ATMEL_PMECC_##reg) + +#define pmecc_writel(addr, reg, value) \ + writel((value), (addr) + ATMEL_PMECC_##reg) + +#define pmecc_readb_ecc_relaxed(addr, sector, n) \ + readb_relaxed((addr) + ATMEL_PMECC_ECCx + ((sector) * 0x40) + (n)) + +#define pmecc_readl_rem_relaxed(addr, sector, n) \ + readl_relaxed((addr) + ATMEL_PMECC_REMx + ((sector) * 0x40) + ((n) * 4)) + +#define pmerrloc_readl_relaxed(addr, reg) \ + readl_relaxed((addr) + ATMEL_PMERRLOC_##reg) + +#define pmerrloc_writel(addr, reg, value) \ + writel((value), (addr) + ATMEL_PMERRLOC_##reg) + +#define pmerrloc_writel_sigma_relaxed(addr, n, value) \ + writel_relaxed((value), (addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4)) + +#define pmerrloc_readl_sigma_relaxed(addr, n) \ + readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4)) + +#define pmerrloc_readl_el_relaxed(addr, n) \ + readl_relaxed((addr) + ATMEL_PMERRLOC_ELx + ((n) * 4)) + +/* Galois field dimension */ +#define PMECC_GF_DIMENSION_13 13 +#define PMECC_GF_DIMENSION_14 14 + +/* Primitive Polynomial used by PMECC */ +#define PMECC_GF_13_PRIMITIVE_POLY 0x201b +#define PMECC_GF_14_PRIMITIVE_POLY 0x4443 + +#define PMECC_LOOKUP_TABLE_SIZE_512 0x2000 +#define PMECC_LOOKUP_TABLE_SIZE_1024 0x4000 + +/* Time out value for reading PMECC status register */ +#define PMECC_MAX_TIMEOUT_MS 100 + +/* Reserved bytes in oob area */ +#define PMECC_OOB_RESERVED_BYTES 2 + +#endif diff --git a/drivers/mtd/nand/atmel_nand_nfc.h b/drivers/mtd/nand/atmel_nand_nfc.h new file mode 100644 index 000000000..4d5d26221 --- /dev/null +++ b/drivers/mtd/nand/atmel_nand_nfc.h @@ -0,0 +1,103 @@ +/* + * Atmel Nand Flash Controller (NFC) - System peripherals regsters. + * Based on SAMA5D3 datasheet. + * + * © Copyright 2013 Atmel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef ATMEL_NAND_NFC_H +#define ATMEL_NAND_NFC_H + +/* + * HSMC NFC registers + */ +#define ATMEL_HSMC_NFC_CFG 0x00 /* NFC Configuration Register */ +#define NFC_CFG_PAGESIZE (7 << 0) +#define NFC_CFG_PAGESIZE_512 (0 << 0) +#define NFC_CFG_PAGESIZE_1024 (1 << 0) +#define NFC_CFG_PAGESIZE_2048 (2 << 0) +#define NFC_CFG_PAGESIZE_4096 (3 << 0) +#define NFC_CFG_PAGESIZE_8192 (4 << 0) +#define NFC_CFG_WSPARE (1 << 8) +#define NFC_CFG_RSPARE (1 << 9) +#define NFC_CFG_NFC_DTOCYC (0xf << 16) +#define NFC_CFG_NFC_DTOMUL (0x7 << 20) +#define NFC_CFG_NFC_SPARESIZE (0x7f << 24) +#define NFC_CFG_NFC_SPARESIZE_BIT_POS 24 + +#define ATMEL_HSMC_NFC_CTRL 0x04 /* NFC Control Register */ +#define NFC_CTRL_ENABLE (1 << 0) +#define NFC_CTRL_DISABLE (1 << 1) + +#define ATMEL_HSMC_NFC_SR 0x08 /* NFC Status Register */ +#define NFC_SR_BUSY (1 << 8) +#define NFC_SR_XFR_DONE (1 << 16) +#define NFC_SR_CMD_DONE (1 << 17) +#define NFC_SR_DTOE (1 << 20) +#define NFC_SR_UNDEF (1 << 21) +#define NFC_SR_AWB (1 << 22) +#define NFC_SR_ASE (1 << 23) +#define NFC_SR_RB_EDGE (1 << 24) + +#define ATMEL_HSMC_NFC_IER 0x0c +#define ATMEL_HSMC_NFC_IDR 0x10 +#define ATMEL_HSMC_NFC_IMR 0x14 +#define ATMEL_HSMC_NFC_CYCLE0 0x18 /* NFC Address Cycle Zero */ +#define ATMEL_HSMC_NFC_ADDR_CYCLE0 (0xff) + +#define ATMEL_HSMC_NFC_BANK 0x1c /* NFC Bank Register */ +#define ATMEL_HSMC_NFC_BANK0 (0 << 0) +#define ATMEL_HSMC_NFC_BANK1 (1 << 0) + +#define nfc_writel(addr, reg, value) \ + writel((value), (addr) + ATMEL_HSMC_NFC_##reg) + +#define nfc_readl(addr, reg) \ + readl_relaxed((addr) + ATMEL_HSMC_NFC_##reg) + +/* + * NFC Address Command definitions + */ +#define NFCADDR_CMD_CMD1 (0xff << 2) /* Command for Cycle 1 */ +#define NFCADDR_CMD_CMD1_BIT_POS 2 +#define NFCADDR_CMD_CMD2 (0xff << 10) /* Command for Cycle 2 */ +#define NFCADDR_CMD_CMD2_BIT_POS 10 +#define NFCADDR_CMD_VCMD2 (0x1 << 18) /* Valid Cycle 2 Command */ +#define NFCADDR_CMD_ACYCLE (0x7 << 19) /* Number of Address required */ +#define NFCADDR_CMD_ACYCLE_NONE (0x0 << 19) +#define NFCADDR_CMD_ACYCLE_1 (0x1 << 19) +#define NFCADDR_CMD_ACYCLE_2 (0x2 << 19) +#define NFCADDR_CMD_ACYCLE_3 (0x3 << 19) +#define NFCADDR_CMD_ACYCLE_4 (0x4 << 19) +#define NFCADDR_CMD_ACYCLE_5 (0x5 << 19) +#define NFCADDR_CMD_ACYCLE_BIT_POS 19 +#define NFCADDR_CMD_CSID (0x7 << 22) /* Chip Select Identifier */ +#define NFCADDR_CMD_CSID_0 (0x0 << 22) +#define NFCADDR_CMD_CSID_1 (0x1 << 22) +#define NFCADDR_CMD_CSID_2 (0x2 << 22) +#define NFCADDR_CMD_CSID_3 (0x3 << 22) +#define NFCADDR_CMD_CSID_4 (0x4 << 22) +#define NFCADDR_CMD_CSID_5 (0x5 << 22) +#define NFCADDR_CMD_CSID_6 (0x6 << 22) +#define NFCADDR_CMD_CSID_7 (0x7 << 22) +#define NFCADDR_CMD_DATAEN (0x1 << 25) /* Data Transfer Enable */ +#define NFCADDR_CMD_DATADIS (0x0 << 25) /* Data Transfer Disable */ +#define NFCADDR_CMD_NFCRD (0x0 << 26) /* NFC Read Enable */ +#define NFCADDR_CMD_NFCWR (0x1 << 26) /* NFC Write Enable */ +#define NFCADDR_CMD_NFCBUSY (0x1 << 27) /* NFC Busy */ + +#define nfc_cmd_addr1234_writel(cmd, addr1234, nfc_base) \ + writel((addr1234), (cmd) + nfc_base) + +#define nfc_cmd_readl(bitstatus, nfc_base) \ + readl_relaxed((bitstatus) + nfc_base) + +#define NFC_TIME_OUT_MS 100 +#define NFC_SRAM_BANK1_OFFSET 0x1200 + +#endif diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c new file mode 100644 index 000000000..c0c3be180 --- /dev/null +++ b/drivers/mtd/nand/au1550nd.c @@ -0,0 +1,515 @@ +/* + * drivers/mtd/nand/au1550nd.c + * + * Copyright (C) 2004 Embedded Edge, LLC + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/slab.h> +#include <linux/gpio.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/platform_device.h> +#include <asm/io.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-au1x00/au1550nd.h> + + +struct au1550nd_ctx { + struct mtd_info info; + struct nand_chip chip; + + int cs; + void __iomem *base; + void (*write_byte)(struct mtd_info *, u_char); +}; + +/** + * au_read_byte - read one byte from the chip + * @mtd: MTD device structure + * + * read function for 8bit buswidth + */ +static u_char au_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + u_char ret = readb(this->IO_ADDR_R); + wmb(); /* drain writebuffer */ + return ret; +} + +/** + * au_write_byte - write one byte to the chip + * @mtd: MTD device structure + * @byte: pointer to data byte to write + * + * write function for 8it buswidth + */ +static void au_write_byte(struct mtd_info *mtd, u_char byte) +{ + struct nand_chip *this = mtd->priv; + writeb(byte, this->IO_ADDR_W); + wmb(); /* drain writebuffer */ +} + +/** + * au_read_byte16 - read one byte endianness aware from the chip + * @mtd: MTD device structure + * + * read function for 16bit buswidth with endianness conversion + */ +static u_char au_read_byte16(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + u_char ret = (u_char) cpu_to_le16(readw(this->IO_ADDR_R)); + wmb(); /* drain writebuffer */ + return ret; +} + +/** + * au_write_byte16 - write one byte endianness aware to the chip + * @mtd: MTD device structure + * @byte: pointer to data byte to write + * + * write function for 16bit buswidth with endianness conversion + */ +static void au_write_byte16(struct mtd_info *mtd, u_char byte) +{ + struct nand_chip *this = mtd->priv; + writew(le16_to_cpu((u16) byte), this->IO_ADDR_W); + wmb(); /* drain writebuffer */ +} + +/** + * au_read_word - read one word from the chip + * @mtd: MTD device structure + * + * read function for 16bit buswidth without endianness conversion + */ +static u16 au_read_word(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + u16 ret = readw(this->IO_ADDR_R); + wmb(); /* drain writebuffer */ + return ret; +} + +/** + * au_write_buf - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + * + * write function for 8bit buswidth + */ +static void au_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + + for (i = 0; i < len; i++) { + writeb(buf[i], this->IO_ADDR_W); + wmb(); /* drain writebuffer */ + } +} + +/** + * au_read_buf - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + * + * read function for 8bit buswidth + */ +static void au_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + + for (i = 0; i < len; i++) { + buf[i] = readb(this->IO_ADDR_R); + wmb(); /* drain writebuffer */ + } +} + +/** + * au_write_buf16 - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + * + * write function for 16bit buswidth + */ +static void au_write_buf16(struct mtd_info *mtd, const u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + u16 *p = (u16 *) buf; + len >>= 1; + + for (i = 0; i < len; i++) { + writew(p[i], this->IO_ADDR_W); + wmb(); /* drain writebuffer */ + } + +} + +/** + * au_read_buf16 - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + * + * read function for 16bit buswidth + */ +static void au_read_buf16(struct mtd_info *mtd, u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + u16 *p = (u16 *) buf; + len >>= 1; + + for (i = 0; i < len; i++) { + p[i] = readw(this->IO_ADDR_R); + wmb(); /* drain writebuffer */ + } +} + +/* Select the chip by setting nCE to low */ +#define NAND_CTL_SETNCE 1 +/* Deselect the chip by setting nCE to high */ +#define NAND_CTL_CLRNCE 2 +/* Select the command latch by setting CLE to high */ +#define NAND_CTL_SETCLE 3 +/* Deselect the command latch by setting CLE to low */ +#define NAND_CTL_CLRCLE 4 +/* Select the address latch by setting ALE to high */ +#define NAND_CTL_SETALE 5 +/* Deselect the address latch by setting ALE to low */ +#define NAND_CTL_CLRALE 6 + +static void au1550_hwcontrol(struct mtd_info *mtd, int cmd) +{ + struct au1550nd_ctx *ctx = container_of(mtd, struct au1550nd_ctx, info); + struct nand_chip *this = mtd->priv; + + switch (cmd) { + + case NAND_CTL_SETCLE: + this->IO_ADDR_W = ctx->base + MEM_STNAND_CMD; + break; + + case NAND_CTL_CLRCLE: + this->IO_ADDR_W = ctx->base + MEM_STNAND_DATA; + break; + + case NAND_CTL_SETALE: + this->IO_ADDR_W = ctx->base + MEM_STNAND_ADDR; + break; + + case NAND_CTL_CLRALE: + this->IO_ADDR_W = ctx->base + MEM_STNAND_DATA; + /* FIXME: Nobody knows why this is necessary, + * but it works only that way */ + udelay(1); + break; + + case NAND_CTL_SETNCE: + /* assert (force assert) chip enable */ + alchemy_wrsmem((1 << (4 + ctx->cs)), AU1000_MEM_STNDCTL); + break; + + case NAND_CTL_CLRNCE: + /* deassert chip enable */ + alchemy_wrsmem(0, AU1000_MEM_STNDCTL); + break; + } + + this->IO_ADDR_R = this->IO_ADDR_W; + + wmb(); /* Drain the writebuffer */ +} + +int au1550_device_ready(struct mtd_info *mtd) +{ + return (alchemy_rdsmem(AU1000_MEM_STSTAT) & 0x1) ? 1 : 0; +} + +/** + * au1550_select_chip - control -CE line + * Forbid driving -CE manually permitting the NAND controller to do this. + * Keeping -CE asserted during the whole sector reads interferes with the + * NOR flash and PCMCIA drivers as it causes contention on the static bus. + * We only have to hold -CE low for the NAND read commands since the flash + * chip needs it to be asserted during chip not ready time but the NAND + * controller keeps it released. + * + * @mtd: MTD device structure + * @chip: chipnumber to select, -1 for deselect + */ +static void au1550_select_chip(struct mtd_info *mtd, int chip) +{ +} + +/** + * au1550_command - Send command to NAND device + * @mtd: MTD device structure + * @command: the command to be sent + * @column: the column address for this command, -1 if none + * @page_addr: the page address for this command, -1 if none + */ +static void au1550_command(struct mtd_info *mtd, unsigned command, int column, int page_addr) +{ + struct au1550nd_ctx *ctx = container_of(mtd, struct au1550nd_ctx, info); + struct nand_chip *this = mtd->priv; + int ce_override = 0, i; + unsigned long flags = 0; + + /* Begin command latch cycle */ + au1550_hwcontrol(mtd, NAND_CTL_SETCLE); + /* + * Write out the command to the device. + */ + if (command == NAND_CMD_SEQIN) { + int readcmd; + + if (column >= mtd->writesize) { + /* OOB area */ + column -= mtd->writesize; + readcmd = NAND_CMD_READOOB; + } else if (column < 256) { + /* First 256 bytes --> READ0 */ + readcmd = NAND_CMD_READ0; + } else { + column -= 256; + readcmd = NAND_CMD_READ1; + } + ctx->write_byte(mtd, readcmd); + } + ctx->write_byte(mtd, command); + + /* Set ALE and clear CLE to start address cycle */ + au1550_hwcontrol(mtd, NAND_CTL_CLRCLE); + + if (column != -1 || page_addr != -1) { + au1550_hwcontrol(mtd, NAND_CTL_SETALE); + + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (this->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + ctx->write_byte(mtd, column); + } + if (page_addr != -1) { + ctx->write_byte(mtd, (u8)(page_addr & 0xff)); + + if (command == NAND_CMD_READ0 || + command == NAND_CMD_READ1 || + command == NAND_CMD_READOOB) { + /* + * NAND controller will release -CE after + * the last address byte is written, so we'll + * have to forcibly assert it. No interrupts + * are allowed while we do this as we don't + * want the NOR flash or PCMCIA drivers to + * steal our precious bytes of data... + */ + ce_override = 1; + local_irq_save(flags); + au1550_hwcontrol(mtd, NAND_CTL_SETNCE); + } + + ctx->write_byte(mtd, (u8)(page_addr >> 8)); + + /* One more address cycle for devices > 32MiB */ + if (this->chipsize > (32 << 20)) + ctx->write_byte(mtd, + ((page_addr >> 16) & 0x0f)); + } + /* Latch in address */ + au1550_hwcontrol(mtd, NAND_CTL_CLRALE); + } + + /* + * Program and erase have their own busy handlers. + * Status and sequential in need no delay. + */ + switch (command) { + + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + break; + + case NAND_CMD_READ0: + case NAND_CMD_READ1: + case NAND_CMD_READOOB: + /* Check if we're really driving -CE low (just in case) */ + if (unlikely(!ce_override)) + break; + + /* Apply a short delay always to ensure that we do wait tWB. */ + ndelay(100); + /* Wait for a chip to become ready... */ + for (i = this->chip_delay; !this->dev_ready(mtd) && i > 0; --i) + udelay(1); + + /* Release -CE and re-enable interrupts. */ + au1550_hwcontrol(mtd, NAND_CTL_CLRNCE); + local_irq_restore(flags); + return; + } + /* Apply this short delay always to ensure that we do wait tWB. */ + ndelay(100); + + while(!this->dev_ready(mtd)); +} + +static int find_nand_cs(unsigned long nand_base) +{ + void __iomem *base = + (void __iomem *)KSEG1ADDR(AU1000_STATIC_MEM_PHYS_ADDR); + unsigned long addr, staddr, start, mask, end; + int i; + + for (i = 0; i < 4; i++) { + addr = 0x1000 + (i * 0x10); /* CSx */ + staddr = __raw_readl(base + addr + 0x08); /* STADDRx */ + /* figure out the decoded range of this CS */ + start = (staddr << 4) & 0xfffc0000; + mask = (staddr << 18) & 0xfffc0000; + end = (start | (start - 1)) & ~(start ^ mask); + if ((nand_base >= start) && (nand_base < end)) + return i; + } + + return -ENODEV; +} + +static int au1550nd_probe(struct platform_device *pdev) +{ + struct au1550nd_platdata *pd; + struct au1550nd_ctx *ctx; + struct nand_chip *this; + struct resource *r; + int ret, cs; + + pd = dev_get_platdata(&pdev->dev); + if (!pd) { + dev_err(&pdev->dev, "missing platform data\n"); + return -ENODEV; + } + + ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + dev_err(&pdev->dev, "no NAND memory resource\n"); + ret = -ENODEV; + goto out1; + } + if (request_mem_region(r->start, resource_size(r), "au1550-nand")) { + dev_err(&pdev->dev, "cannot claim NAND memory area\n"); + ret = -ENOMEM; + goto out1; + } + + ctx->base = ioremap_nocache(r->start, 0x1000); + if (!ctx->base) { + dev_err(&pdev->dev, "cannot remap NAND memory area\n"); + ret = -ENODEV; + goto out2; + } + + this = &ctx->chip; + ctx->info.priv = this; + ctx->info.owner = THIS_MODULE; + + /* figure out which CS# r->start belongs to */ + cs = find_nand_cs(r->start); + if (cs < 0) { + dev_err(&pdev->dev, "cannot detect NAND chipselect\n"); + ret = -ENODEV; + goto out3; + } + ctx->cs = cs; + + this->dev_ready = au1550_device_ready; + this->select_chip = au1550_select_chip; + this->cmdfunc = au1550_command; + + /* 30 us command delay time */ + this->chip_delay = 30; + this->ecc.mode = NAND_ECC_SOFT; + + if (pd->devwidth) + this->options |= NAND_BUSWIDTH_16; + + this->read_byte = (pd->devwidth) ? au_read_byte16 : au_read_byte; + ctx->write_byte = (pd->devwidth) ? au_write_byte16 : au_write_byte; + this->read_word = au_read_word; + this->write_buf = (pd->devwidth) ? au_write_buf16 : au_write_buf; + this->read_buf = (pd->devwidth) ? au_read_buf16 : au_read_buf; + + ret = nand_scan(&ctx->info, 1); + if (ret) { + dev_err(&pdev->dev, "NAND scan failed with %d\n", ret); + goto out3; + } + + mtd_device_register(&ctx->info, pd->parts, pd->num_parts); + + platform_set_drvdata(pdev, ctx); + + return 0; + +out3: + iounmap(ctx->base); +out2: + release_mem_region(r->start, resource_size(r)); +out1: + kfree(ctx); + return ret; +} + +static int au1550nd_remove(struct platform_device *pdev) +{ + struct au1550nd_ctx *ctx = platform_get_drvdata(pdev); + struct resource *r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + nand_release(&ctx->info); + iounmap(ctx->base); + release_mem_region(r->start, 0x1000); + kfree(ctx); + return 0; +} + +static struct platform_driver au1550nd_driver = { + .driver = { + .name = "au1550-nand", + }, + .probe = au1550nd_probe, + .remove = au1550nd_remove, +}; + +module_platform_driver(au1550nd_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Embedded Edge, LLC"); +MODULE_DESCRIPTION("Board-specific glue layer for NAND flash on Pb1550 board"); diff --git a/drivers/mtd/nand/bcm47xxnflash/Makefile b/drivers/mtd/nand/bcm47xxnflash/Makefile new file mode 100644 index 000000000..f05b119e1 --- /dev/null +++ b/drivers/mtd/nand/bcm47xxnflash/Makefile @@ -0,0 +1,4 @@ +bcm47xxnflash-y += main.o +bcm47xxnflash-y += ops_bcm4706.o + +obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash.o diff --git a/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h b/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h new file mode 100644 index 000000000..c005a6233 --- /dev/null +++ b/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h @@ -0,0 +1,26 @@ +#ifndef __BCM47XXNFLASH_H +#define __BCM47XXNFLASH_H + +#ifndef pr_fmt +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt +#endif + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> + +struct bcm47xxnflash { + struct bcma_drv_cc *cc; + + struct nand_chip nand_chip; + struct mtd_info mtd; + + unsigned curr_command; + int curr_page_addr; + int curr_column; + + u8 id_data[8]; +}; + +int bcm47xxnflash_ops_bcm4706_init(struct bcm47xxnflash *b47n); + +#endif /* BCM47XXNFLASH */ diff --git a/drivers/mtd/nand/bcm47xxnflash/main.c b/drivers/mtd/nand/bcm47xxnflash/main.c new file mode 100644 index 000000000..461577cfb --- /dev/null +++ b/drivers/mtd/nand/bcm47xxnflash/main.c @@ -0,0 +1,79 @@ +/* + * BCM47XX NAND flash driver + * + * Copyright (C) 2012 Rafał Miłecki <zajec5@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include "bcm47xxnflash.h" + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/slab.h> +#include <linux/platform_device.h> +#include <linux/bcma/bcma.h> + +MODULE_DESCRIPTION("NAND flash driver for BCMA bus"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Rafał Miłecki"); + +static const char *probes[] = { "bcm47xxpart", NULL }; + +static int bcm47xxnflash_probe(struct platform_device *pdev) +{ + struct bcma_nflash *nflash = dev_get_platdata(&pdev->dev); + struct bcm47xxnflash *b47n; + int err = 0; + + b47n = devm_kzalloc(&pdev->dev, sizeof(*b47n), GFP_KERNEL); + if (!b47n) + return -ENOMEM; + + b47n->nand_chip.priv = b47n; + b47n->mtd.owner = THIS_MODULE; + b47n->mtd.priv = &b47n->nand_chip; /* Required */ + b47n->cc = container_of(nflash, struct bcma_drv_cc, nflash); + + if (b47n->cc->core->bus->chipinfo.id == BCMA_CHIP_ID_BCM4706) { + err = bcm47xxnflash_ops_bcm4706_init(b47n); + } else { + pr_err("Device not supported\n"); + err = -ENOTSUPP; + } + if (err) { + pr_err("Initialization failed: %d\n", err); + return err; + } + + err = mtd_device_parse_register(&b47n->mtd, probes, NULL, NULL, 0); + if (err) { + pr_err("Failed to register MTD device: %d\n", err); + return err; + } + + return 0; +} + +static int bcm47xxnflash_remove(struct platform_device *pdev) +{ + struct bcma_nflash *nflash = dev_get_platdata(&pdev->dev); + + if (nflash->mtd) + mtd_device_unregister(nflash->mtd); + + return 0; +} + +static struct platform_driver bcm47xxnflash_driver = { + .probe = bcm47xxnflash_probe, + .remove = bcm47xxnflash_remove, + .driver = { + .name = "bcma_nflash", + }, +}; + +module_platform_driver(bcm47xxnflash_driver); diff --git a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c b/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c new file mode 100644 index 000000000..592befc7f --- /dev/null +++ b/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c @@ -0,0 +1,454 @@ +/* + * BCM47XX NAND flash driver + * + * Copyright (C) 2012 Rafał Miłecki <zajec5@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include "bcm47xxnflash.h" + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/bcma/bcma.h> + +/* Broadcom uses 1'000'000 but it seems to be too many. Tests on WNDR4500 has + * shown ~1000 retries as maxiumum. */ +#define NFLASH_READY_RETRIES 10000 + +#define NFLASH_SECTOR_SIZE 512 + +#define NCTL_CMD0 0x00010000 +#define NCTL_COL 0x00020000 /* Update column with value from BCMA_CC_NFLASH_COL_ADDR */ +#define NCTL_ROW 0x00040000 /* Update row (page) with value from BCMA_CC_NFLASH_ROW_ADDR */ +#define NCTL_CMD1W 0x00080000 +#define NCTL_READ 0x00100000 +#define NCTL_WRITE 0x00200000 +#define NCTL_SPECADDR 0x01000000 +#define NCTL_READY 0x04000000 +#define NCTL_ERR 0x08000000 +#define NCTL_CSA 0x40000000 +#define NCTL_START 0x80000000 + +/************************************************** + * Various helpers + **************************************************/ + +static inline u8 bcm47xxnflash_ops_bcm4706_ns_to_cycle(u16 ns, u16 clock) +{ + return ((ns * 1000 * clock) / 1000000) + 1; +} + +static int bcm47xxnflash_ops_bcm4706_ctl_cmd(struct bcma_drv_cc *cc, u32 code) +{ + int i = 0; + + bcma_cc_write32(cc, BCMA_CC_NFLASH_CTL, NCTL_START | code); + for (i = 0; i < NFLASH_READY_RETRIES; i++) { + if (!(bcma_cc_read32(cc, BCMA_CC_NFLASH_CTL) & NCTL_START)) { + i = 0; + break; + } + } + if (i) { + pr_err("NFLASH control command not ready!\n"); + return -EBUSY; + } + return 0; +} + +static int bcm47xxnflash_ops_bcm4706_poll(struct bcma_drv_cc *cc) +{ + int i; + + for (i = 0; i < NFLASH_READY_RETRIES; i++) { + if (bcma_cc_read32(cc, BCMA_CC_NFLASH_CTL) & NCTL_READY) { + if (bcma_cc_read32(cc, BCMA_CC_NFLASH_CTL) & + BCMA_CC_NFLASH_CTL_ERR) { + pr_err("Error on polling\n"); + return -EBUSY; + } else { + return 0; + } + } + } + + pr_err("Polling timeout!\n"); + return -EBUSY; +} + +/************************************************** + * R/W + **************************************************/ + +static void bcm47xxnflash_ops_bcm4706_read(struct mtd_info *mtd, uint8_t *buf, + int len) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + + u32 ctlcode; + u32 *dest = (u32 *)buf; + int i; + int toread; + + BUG_ON(b47n->curr_page_addr & ~nand_chip->pagemask); + /* Don't validate column using nand_chip->page_shift, it may be bigger + * when accessing OOB */ + + while (len) { + /* We can read maximum of 0x200 bytes at once */ + toread = min(len, 0x200); + + /* Set page and column */ + bcma_cc_write32(b47n->cc, BCMA_CC_NFLASH_COL_ADDR, + b47n->curr_column); + bcma_cc_write32(b47n->cc, BCMA_CC_NFLASH_ROW_ADDR, + b47n->curr_page_addr); + + /* Prepare to read */ + ctlcode = NCTL_CSA | NCTL_CMD1W | NCTL_ROW | NCTL_COL | + NCTL_CMD0; + ctlcode |= NAND_CMD_READSTART << 8; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(b47n->cc, ctlcode)) + return; + if (bcm47xxnflash_ops_bcm4706_poll(b47n->cc)) + return; + + /* Eventually read some data :) */ + for (i = 0; i < toread; i += 4, dest++) { + ctlcode = NCTL_CSA | 0x30000000 | NCTL_READ; + if (i == toread - 4) /* Last read goes without that */ + ctlcode &= ~NCTL_CSA; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(b47n->cc, + ctlcode)) + return; + *dest = bcma_cc_read32(b47n->cc, BCMA_CC_NFLASH_DATA); + } + + b47n->curr_column += toread; + len -= toread; + } +} + +static void bcm47xxnflash_ops_bcm4706_write(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + struct bcma_drv_cc *cc = b47n->cc; + + u32 ctlcode; + const u32 *data = (u32 *)buf; + int i; + + BUG_ON(b47n->curr_page_addr & ~nand_chip->pagemask); + /* Don't validate column using nand_chip->page_shift, it may be bigger + * when accessing OOB */ + + for (i = 0; i < len; i += 4, data++) { + bcma_cc_write32(cc, BCMA_CC_NFLASH_DATA, *data); + + ctlcode = NCTL_CSA | 0x30000000 | NCTL_WRITE; + if (i == len - 4) /* Last read goes without that */ + ctlcode &= ~NCTL_CSA; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, ctlcode)) { + pr_err("%s ctl_cmd didn't work!\n", __func__); + return; + } + } + + b47n->curr_column += len; +} + +/************************************************** + * NAND chip ops + **************************************************/ + +static void bcm47xxnflash_ops_bcm4706_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + u32 code = 0; + + if (cmd == NAND_CMD_NONE) + return; + + if (cmd & NAND_CTRL_CLE) + code = cmd | NCTL_CMD0; + + /* nCS is not needed for reset command */ + if (cmd != NAND_CMD_RESET) + code |= NCTL_CSA; + + bcm47xxnflash_ops_bcm4706_ctl_cmd(b47n->cc, code); +} + +/* Default nand_select_chip calls cmd_ctrl, which is not used in BCM4706 */ +static void bcm47xxnflash_ops_bcm4706_select_chip(struct mtd_info *mtd, + int chip) +{ + return; +} + +static int bcm47xxnflash_ops_bcm4706_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + + return !!(bcma_cc_read32(b47n->cc, BCMA_CC_NFLASH_CTL) & NCTL_READY); +} + +/* + * Default nand_command and nand_command_lp don't match BCM4706 hardware layout. + * For example, reading chip id is performed in a non-standard way. + * Setting column and page is also handled differently, we use a special + * registers of ChipCommon core. Hacking cmd_ctrl to understand and convert + * standard commands would be much more complicated. + */ +static void bcm47xxnflash_ops_bcm4706_cmdfunc(struct mtd_info *mtd, + unsigned command, int column, + int page_addr) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + struct bcma_drv_cc *cc = b47n->cc; + u32 ctlcode; + int i; + + if (column != -1) + b47n->curr_column = column; + if (page_addr != -1) + b47n->curr_page_addr = page_addr; + + switch (command) { + case NAND_CMD_RESET: + nand_chip->cmd_ctrl(mtd, command, NAND_CTRL_CLE); + + ndelay(100); + nand_wait_ready(mtd); + break; + case NAND_CMD_READID: + ctlcode = NCTL_CSA | 0x01000000 | NCTL_CMD1W | NCTL_CMD0; + ctlcode |= NAND_CMD_READID; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(b47n->cc, ctlcode)) { + pr_err("READID error\n"); + break; + } + + /* + * Reading is specific, last one has to go without NCTL_CSA + * bit. We don't know how many reads NAND subsystem is going + * to perform, so cache everything. + */ + for (i = 0; i < ARRAY_SIZE(b47n->id_data); i++) { + ctlcode = NCTL_CSA | NCTL_READ; + if (i == ARRAY_SIZE(b47n->id_data) - 1) + ctlcode &= ~NCTL_CSA; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(b47n->cc, + ctlcode)) { + pr_err("READID error\n"); + break; + } + b47n->id_data[i] = + bcma_cc_read32(b47n->cc, BCMA_CC_NFLASH_DATA) + & 0xFF; + } + + break; + case NAND_CMD_STATUS: + ctlcode = NCTL_CSA | NCTL_CMD0 | NAND_CMD_STATUS; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, ctlcode)) + pr_err("STATUS command error\n"); + break; + case NAND_CMD_READ0: + break; + case NAND_CMD_READOOB: + if (page_addr != -1) + b47n->curr_column += mtd->writesize; + break; + case NAND_CMD_ERASE1: + bcma_cc_write32(cc, BCMA_CC_NFLASH_ROW_ADDR, + b47n->curr_page_addr); + ctlcode = NCTL_ROW | NCTL_CMD1W | NCTL_CMD0 | + NAND_CMD_ERASE1 | (NAND_CMD_ERASE2 << 8); + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, ctlcode)) + pr_err("ERASE1 failed\n"); + break; + case NAND_CMD_ERASE2: + break; + case NAND_CMD_SEQIN: + /* Set page and column */ + bcma_cc_write32(cc, BCMA_CC_NFLASH_COL_ADDR, + b47n->curr_column); + bcma_cc_write32(cc, BCMA_CC_NFLASH_ROW_ADDR, + b47n->curr_page_addr); + + /* Prepare to write */ + ctlcode = 0x40000000 | NCTL_ROW | NCTL_COL | NCTL_CMD0; + ctlcode |= NAND_CMD_SEQIN; + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, ctlcode)) + pr_err("SEQIN failed\n"); + break; + case NAND_CMD_PAGEPROG: + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, NCTL_CMD0 | + NAND_CMD_PAGEPROG)) + pr_err("PAGEPROG failed\n"); + if (bcm47xxnflash_ops_bcm4706_poll(cc)) + pr_err("PAGEPROG not ready\n"); + break; + default: + pr_err("Command 0x%X unsupported\n", command); + break; + } + b47n->curr_command = command; +} + +static u8 bcm47xxnflash_ops_bcm4706_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + struct bcma_drv_cc *cc = b47n->cc; + u32 tmp = 0; + + switch (b47n->curr_command) { + case NAND_CMD_READID: + if (b47n->curr_column >= ARRAY_SIZE(b47n->id_data)) { + pr_err("Requested invalid id_data: %d\n", + b47n->curr_column); + return 0; + } + return b47n->id_data[b47n->curr_column++]; + case NAND_CMD_STATUS: + if (bcm47xxnflash_ops_bcm4706_ctl_cmd(cc, NCTL_READ)) + return 0; + return bcma_cc_read32(cc, BCMA_CC_NFLASH_DATA) & 0xff; + case NAND_CMD_READOOB: + bcm47xxnflash_ops_bcm4706_read(mtd, (u8 *)&tmp, 4); + return tmp & 0xFF; + } + + pr_err("Invalid command for byte read: 0x%X\n", b47n->curr_command); + return 0; +} + +static void bcm47xxnflash_ops_bcm4706_read_buf(struct mtd_info *mtd, + uint8_t *buf, int len) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + + switch (b47n->curr_command) { + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + bcm47xxnflash_ops_bcm4706_read(mtd, buf, len); + return; + } + + pr_err("Invalid command for buf read: 0x%X\n", b47n->curr_command); +} + +static void bcm47xxnflash_ops_bcm4706_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + struct nand_chip *nand_chip = (struct nand_chip *)mtd->priv; + struct bcm47xxnflash *b47n = (struct bcm47xxnflash *)nand_chip->priv; + + switch (b47n->curr_command) { + case NAND_CMD_SEQIN: + bcm47xxnflash_ops_bcm4706_write(mtd, buf, len); + return; + } + + pr_err("Invalid command for buf write: 0x%X\n", b47n->curr_command); +} + +/************************************************** + * Init + **************************************************/ + +int bcm47xxnflash_ops_bcm4706_init(struct bcm47xxnflash *b47n) +{ + struct nand_chip *nand_chip = (struct nand_chip *)&b47n->nand_chip; + int err; + u32 freq; + u16 clock; + u8 w0, w1, w2, w3, w4; + + unsigned long chipsize; /* MiB */ + u8 tbits, col_bits, col_size, row_bits, row_bsize; + u32 val; + + b47n->nand_chip.select_chip = bcm47xxnflash_ops_bcm4706_select_chip; + nand_chip->cmd_ctrl = bcm47xxnflash_ops_bcm4706_cmd_ctrl; + nand_chip->dev_ready = bcm47xxnflash_ops_bcm4706_dev_ready; + b47n->nand_chip.cmdfunc = bcm47xxnflash_ops_bcm4706_cmdfunc; + b47n->nand_chip.read_byte = bcm47xxnflash_ops_bcm4706_read_byte; + b47n->nand_chip.read_buf = bcm47xxnflash_ops_bcm4706_read_buf; + b47n->nand_chip.write_buf = bcm47xxnflash_ops_bcm4706_write_buf; + + nand_chip->chip_delay = 50; + b47n->nand_chip.bbt_options = NAND_BBT_USE_FLASH; + b47n->nand_chip.ecc.mode = NAND_ECC_NONE; /* TODO: implement ECC */ + + /* Enable NAND flash access */ + bcma_cc_set32(b47n->cc, BCMA_CC_4706_FLASHSCFG, + BCMA_CC_4706_FLASHSCFG_NF1); + + /* Configure wait counters */ + if (b47n->cc->status & BCMA_CC_CHIPST_4706_PKG_OPTION) { + /* 400 MHz */ + freq = 400000000 / 4; + } else { + freq = bcma_chipco_pll_read(b47n->cc, 4); + freq = (freq & 0xFFF) >> 3; + /* Fixed reference clock 25 MHz and m = 2 */ + freq = (freq * 25000000 / 2) / 4; + } + clock = freq / 1000000; + w0 = bcm47xxnflash_ops_bcm4706_ns_to_cycle(15, clock); + w1 = bcm47xxnflash_ops_bcm4706_ns_to_cycle(20, clock); + w2 = bcm47xxnflash_ops_bcm4706_ns_to_cycle(10, clock); + w3 = bcm47xxnflash_ops_bcm4706_ns_to_cycle(10, clock); + w4 = bcm47xxnflash_ops_bcm4706_ns_to_cycle(100, clock); + bcma_cc_write32(b47n->cc, BCMA_CC_NFLASH_WAITCNT0, + (w4 << 24 | w3 << 18 | w2 << 12 | w1 << 6 | w0)); + + /* Scan NAND */ + err = nand_scan(&b47n->mtd, 1); + if (err) { + pr_err("Could not scan NAND flash: %d\n", err); + goto exit; + } + + /* Configure FLASH */ + chipsize = b47n->nand_chip.chipsize >> 20; + tbits = ffs(chipsize); /* find first bit set */ + if (!tbits || tbits != fls(chipsize)) { + pr_err("Invalid flash size: 0x%lX\n", chipsize); + err = -ENOTSUPP; + goto exit; + } + tbits += 19; /* Broadcom increases *index* by 20, we increase *pos* */ + + col_bits = b47n->nand_chip.page_shift + 1; + col_size = (col_bits + 7) / 8; + + row_bits = tbits - col_bits + 1; + row_bsize = (row_bits + 7) / 8; + + val = ((row_bsize - 1) << 6) | ((col_size - 1) << 4) | 2; + bcma_cc_write32(b47n->cc, BCMA_CC_NFLASH_CONF, val); + +exit: + if (err) + bcma_cc_mask32(b47n->cc, BCMA_CC_4706_FLASHSCFG, + ~BCMA_CC_4706_FLASHSCFG_NF1); + return err; +} diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/bf5xx_nand.c new file mode 100644 index 000000000..4d8d4ba4b --- /dev/null +++ b/drivers/mtd/nand/bf5xx_nand.c @@ -0,0 +1,847 @@ +/* linux/drivers/mtd/nand/bf5xx_nand.c + * + * Copyright 2006-2008 Analog Devices Inc. + * http://blackfin.uclinux.org/ + * Bryan Wu <bryan.wu@analog.com> + * + * Blackfin BF5xx on-chip NAND flash controller driver + * + * Derived from drivers/mtd/nand/s3c2410.c + * Copyright (c) 2007 Ben Dooks <ben@simtec.co.uk> + * + * Derived from drivers/mtd/nand/cafe.c + * Copyright © 2006 Red Hat, Inc. + * Copyright © 2006 David Woodhouse <dwmw2@infradead.org> + * + * Changelog: + * 12-Jun-2007 Bryan Wu: Initial version + * 18-Jul-2007 Bryan Wu: + * - ECC_HW and ECC_SW supported + * - DMA supported in ECC_HW + * - YAFFS tested as rootfs in both ECC_HW and ECC_SW + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/io.h> +#include <linux/bitops.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/blackfin.h> +#include <asm/dma.h> +#include <asm/cacheflush.h> +#include <asm/nand.h> +#include <asm/portmux.h> + +#define DRV_NAME "bf5xx-nand" +#define DRV_VERSION "1.2" +#define DRV_AUTHOR "Bryan Wu <bryan.wu@analog.com>" +#define DRV_DESC "BF5xx on-chip NAND FLash Controller Driver" + +/* NFC_STAT Masks */ +#define NBUSY 0x01 /* Not Busy */ +#define WB_FULL 0x02 /* Write Buffer Full */ +#define PG_WR_STAT 0x04 /* Page Write Pending */ +#define PG_RD_STAT 0x08 /* Page Read Pending */ +#define WB_EMPTY 0x10 /* Write Buffer Empty */ + +/* NFC_IRQSTAT Masks */ +#define NBUSYIRQ 0x01 /* Not Busy IRQ */ +#define WB_OVF 0x02 /* Write Buffer Overflow */ +#define WB_EDGE 0x04 /* Write Buffer Edge Detect */ +#define RD_RDY 0x08 /* Read Data Ready */ +#define WR_DONE 0x10 /* Page Write Done */ + +/* NFC_RST Masks */ +#define ECC_RST 0x01 /* ECC (and NFC counters) Reset */ + +/* NFC_PGCTL Masks */ +#define PG_RD_START 0x01 /* Page Read Start */ +#define PG_WR_START 0x02 /* Page Write Start */ + +#ifdef CONFIG_MTD_NAND_BF5XX_HWECC +static int hardware_ecc = 1; +#else +static int hardware_ecc; +#endif + +static const unsigned short bfin_nfc_pin_req[] = + {P_NAND_CE, + P_NAND_RB, + P_NAND_D0, + P_NAND_D1, + P_NAND_D2, + P_NAND_D3, + P_NAND_D4, + P_NAND_D5, + P_NAND_D6, + P_NAND_D7, + P_NAND_WE, + P_NAND_RE, + P_NAND_CLE, + P_NAND_ALE, + 0}; + +#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC +static struct nand_ecclayout bootrom_ecclayout = { + .eccbytes = 24, + .eccpos = { + 0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2, + 0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2, + 0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2, + 0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2, + 0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2, + 0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2, + 0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2, + 0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2 + }, + .oobfree = { + { 0x8 * 0 + 3, 5 }, + { 0x8 * 1 + 3, 5 }, + { 0x8 * 2 + 3, 5 }, + { 0x8 * 3 + 3, 5 }, + { 0x8 * 4 + 3, 5 }, + { 0x8 * 5 + 3, 5 }, + { 0x8 * 6 + 3, 5 }, + { 0x8 * 7 + 3, 5 }, + } +}; +#endif + +/* + * Data structures for bf5xx nand flash controller driver + */ + +/* bf5xx nand info */ +struct bf5xx_nand_info { + /* mtd info */ + struct nand_hw_control controller; + struct mtd_info mtd; + struct nand_chip chip; + + /* platform info */ + struct bf5xx_nand_platform *platform; + + /* device info */ + struct device *device; + + /* DMA stuff */ + struct completion dma_completion; +}; + +/* + * Conversion functions + */ +static struct bf5xx_nand_info *mtd_to_nand_info(struct mtd_info *mtd) +{ + return container_of(mtd, struct bf5xx_nand_info, mtd); +} + +static struct bf5xx_nand_info *to_nand_info(struct platform_device *pdev) +{ + return platform_get_drvdata(pdev); +} + +static struct bf5xx_nand_platform *to_nand_plat(struct platform_device *pdev) +{ + return dev_get_platdata(&pdev->dev); +} + +/* + * struct nand_chip interface function pointers + */ + +/* + * bf5xx_nand_hwcontrol + * + * Issue command and address cycles to the chip + */ +static void bf5xx_nand_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + if (cmd == NAND_CMD_NONE) + return; + + while (bfin_read_NFC_STAT() & WB_FULL) + cpu_relax(); + + if (ctrl & NAND_CLE) + bfin_write_NFC_CMD(cmd); + else if (ctrl & NAND_ALE) + bfin_write_NFC_ADDR(cmd); + SSYNC(); +} + +/* + * bf5xx_nand_devready() + * + * returns 0 if the nand is busy, 1 if it is ready + */ +static int bf5xx_nand_devready(struct mtd_info *mtd) +{ + unsigned short val = bfin_read_NFC_STAT(); + + if ((val & NBUSY) == NBUSY) + return 1; + else + return 0; +} + +/* + * ECC functions + * These allow the bf5xx to use the controller's ECC + * generator block to ECC the data as it passes through + */ + +/* + * ECC error correction function + */ +static int bf5xx_nand_correct_data_256(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct bf5xx_nand_info *info = mtd_to_nand_info(mtd); + u32 syndrome[5]; + u32 calced, stored; + int i; + unsigned short failing_bit, failing_byte; + u_char data; + + calced = calc_ecc[0] | (calc_ecc[1] << 8) | (calc_ecc[2] << 16); + stored = read_ecc[0] | (read_ecc[1] << 8) | (read_ecc[2] << 16); + + syndrome[0] = (calced ^ stored); + + /* + * syndrome 0: all zero + * No error in data + * No action + */ + if (!syndrome[0] || !calced || !stored) + return 0; + + /* + * sysdrome 0: only one bit is one + * ECC data was incorrect + * No action + */ + if (hweight32(syndrome[0]) == 1) { + dev_err(info->device, "ECC data was incorrect!\n"); + return 1; + } + + syndrome[1] = (calced & 0x7FF) ^ (stored & 0x7FF); + syndrome[2] = (calced & 0x7FF) ^ ((calced >> 11) & 0x7FF); + syndrome[3] = (stored & 0x7FF) ^ ((stored >> 11) & 0x7FF); + syndrome[4] = syndrome[2] ^ syndrome[3]; + + for (i = 0; i < 5; i++) + dev_info(info->device, "syndrome[%d] 0x%08x\n", i, syndrome[i]); + + dev_info(info->device, + "calced[0x%08x], stored[0x%08x]\n", + calced, stored); + + /* + * sysdrome 0: exactly 11 bits are one, each parity + * and parity' pair is 1 & 0 or 0 & 1. + * 1-bit correctable error + * Correct the error + */ + if (hweight32(syndrome[0]) == 11 && syndrome[4] == 0x7FF) { + dev_info(info->device, + "1-bit correctable error, correct it.\n"); + dev_info(info->device, + "syndrome[1] 0x%08x\n", syndrome[1]); + + failing_bit = syndrome[1] & 0x7; + failing_byte = syndrome[1] >> 0x3; + data = *(dat + failing_byte); + data = data ^ (0x1 << failing_bit); + *(dat + failing_byte) = data; + + return 0; + } + + /* + * sysdrome 0: random data + * More than 1-bit error, non-correctable error + * Discard data, mark bad block + */ + dev_err(info->device, + "More than 1-bit error, non-correctable error.\n"); + dev_err(info->device, + "Please discard data, mark bad block\n"); + + return 1; +} + +static int bf5xx_nand_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct nand_chip *chip = mtd->priv; + int ret; + + ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc); + + /* If ecc size is 512, correct second 256 bytes */ + if (chip->ecc.size == 512) { + dat += 256; + read_ecc += 3; + calc_ecc += 3; + ret |= bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc); + } + + return ret; +} + +static void bf5xx_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + return; +} + +static int bf5xx_nand_calculate_ecc(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_code) +{ + struct bf5xx_nand_info *info = mtd_to_nand_info(mtd); + struct nand_chip *chip = mtd->priv; + u16 ecc0, ecc1; + u32 code[2]; + u8 *p; + + /* first 3 bytes ECC code for 256 page size */ + ecc0 = bfin_read_NFC_ECC0(); + ecc1 = bfin_read_NFC_ECC1(); + + code[0] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11); + + dev_dbg(info->device, "returning ecc 0x%08x\n", code[0]); + + p = (u8 *) code; + memcpy(ecc_code, p, 3); + + /* second 3 bytes ECC code for 512 ecc size */ + if (chip->ecc.size == 512) { + ecc0 = bfin_read_NFC_ECC2(); + ecc1 = bfin_read_NFC_ECC3(); + code[1] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11); + + /* second 3 bytes in ecc_code for second 256 + * bytes of 512 page size + */ + p = (u8 *) (code + 1); + memcpy((ecc_code + 3), p, 3); + dev_dbg(info->device, "returning ecc 0x%08x\n", code[1]); + } + + return 0; +} + +/* + * PIO mode for buffer writing and reading + */ +static void bf5xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + int i; + unsigned short val; + + /* + * Data reads are requested by first writing to NFC_DATA_RD + * and then reading back from NFC_READ. + */ + for (i = 0; i < len; i++) { + while (bfin_read_NFC_STAT() & WB_FULL) + cpu_relax(); + + /* Contents do not matter */ + bfin_write_NFC_DATA_RD(0x0000); + SSYNC(); + + while ((bfin_read_NFC_IRQSTAT() & RD_RDY) != RD_RDY) + cpu_relax(); + + buf[i] = bfin_read_NFC_READ(); + + val = bfin_read_NFC_IRQSTAT(); + val |= RD_RDY; + bfin_write_NFC_IRQSTAT(val); + SSYNC(); + } +} + +static uint8_t bf5xx_nand_read_byte(struct mtd_info *mtd) +{ + uint8_t val; + + bf5xx_nand_read_buf(mtd, &val, 1); + + return val; +} + +static void bf5xx_nand_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + int i; + + for (i = 0; i < len; i++) { + while (bfin_read_NFC_STAT() & WB_FULL) + cpu_relax(); + + bfin_write_NFC_DATA_WR(buf[i]); + SSYNC(); + } +} + +static void bf5xx_nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len) +{ + int i; + u16 *p = (u16 *) buf; + len >>= 1; + + /* + * Data reads are requested by first writing to NFC_DATA_RD + * and then reading back from NFC_READ. + */ + bfin_write_NFC_DATA_RD(0x5555); + + SSYNC(); + + for (i = 0; i < len; i++) + p[i] = bfin_read_NFC_READ(); +} + +static void bf5xx_nand_write_buf16(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + int i; + u16 *p = (u16 *) buf; + len >>= 1; + + for (i = 0; i < len; i++) + bfin_write_NFC_DATA_WR(p[i]); + + SSYNC(); +} + +/* + * DMA functions for buffer writing and reading + */ +static irqreturn_t bf5xx_nand_dma_irq(int irq, void *dev_id) +{ + struct bf5xx_nand_info *info = dev_id; + + clear_dma_irqstat(CH_NFC); + disable_dma(CH_NFC); + complete(&info->dma_completion); + + return IRQ_HANDLED; +} + +static void bf5xx_nand_dma_rw(struct mtd_info *mtd, + uint8_t *buf, int is_read) +{ + struct bf5xx_nand_info *info = mtd_to_nand_info(mtd); + struct nand_chip *chip = mtd->priv; + unsigned short val; + + dev_dbg(info->device, " mtd->%p, buf->%p, is_read %d\n", + mtd, buf, is_read); + + /* + * Before starting a dma transfer, be sure to invalidate/flush + * the cache over the address range of your DMA buffer to + * prevent cache coherency problems. Otherwise very subtle bugs + * can be introduced to your driver. + */ + if (is_read) + invalidate_dcache_range((unsigned int)buf, + (unsigned int)(buf + chip->ecc.size)); + else + flush_dcache_range((unsigned int)buf, + (unsigned int)(buf + chip->ecc.size)); + + /* + * This register must be written before each page is + * transferred to generate the correct ECC register + * values. + */ + bfin_write_NFC_RST(ECC_RST); + SSYNC(); + while (bfin_read_NFC_RST() & ECC_RST) + cpu_relax(); + + disable_dma(CH_NFC); + clear_dma_irqstat(CH_NFC); + + /* setup DMA register with Blackfin DMA API */ + set_dma_config(CH_NFC, 0x0); + set_dma_start_addr(CH_NFC, (unsigned long) buf); + + /* The DMAs have different size on BF52x and BF54x */ +#ifdef CONFIG_BF52x + set_dma_x_count(CH_NFC, (chip->ecc.size >> 1)); + set_dma_x_modify(CH_NFC, 2); + val = DI_EN | WDSIZE_16; +#endif + +#ifdef CONFIG_BF54x + set_dma_x_count(CH_NFC, (chip->ecc.size >> 2)); + set_dma_x_modify(CH_NFC, 4); + val = DI_EN | WDSIZE_32; +#endif + /* setup write or read operation */ + if (is_read) + val |= WNR; + set_dma_config(CH_NFC, val); + enable_dma(CH_NFC); + + /* Start PAGE read/write operation */ + if (is_read) + bfin_write_NFC_PGCTL(PG_RD_START); + else + bfin_write_NFC_PGCTL(PG_WR_START); + wait_for_completion(&info->dma_completion); +} + +static void bf5xx_nand_dma_read_buf(struct mtd_info *mtd, + uint8_t *buf, int len) +{ + struct bf5xx_nand_info *info = mtd_to_nand_info(mtd); + struct nand_chip *chip = mtd->priv; + + dev_dbg(info->device, "mtd->%p, buf->%p, int %d\n", mtd, buf, len); + + if (len == chip->ecc.size) + bf5xx_nand_dma_rw(mtd, buf, 1); + else + bf5xx_nand_read_buf(mtd, buf, len); +} + +static void bf5xx_nand_dma_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + struct bf5xx_nand_info *info = mtd_to_nand_info(mtd); + struct nand_chip *chip = mtd->priv; + + dev_dbg(info->device, "mtd->%p, buf->%p, len %d\n", mtd, buf, len); + + if (len == chip->ecc.size) + bf5xx_nand_dma_rw(mtd, (uint8_t *)buf, 0); + else + bf5xx_nand_write_buf(mtd, buf, len); +} + +static int bf5xx_nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + bf5xx_nand_read_buf(mtd, buf, mtd->writesize); + bf5xx_nand_read_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static int bf5xx_nand_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + bf5xx_nand_write_buf(mtd, buf, mtd->writesize); + bf5xx_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +/* + * System initialization functions + */ +static int bf5xx_nand_dma_init(struct bf5xx_nand_info *info) +{ + int ret; + + /* Do not use dma */ + if (!hardware_ecc) + return 0; + + init_completion(&info->dma_completion); + + /* Request NFC DMA channel */ + ret = request_dma(CH_NFC, "BF5XX NFC driver"); + if (ret < 0) { + dev_err(info->device, " unable to get DMA channel\n"); + return ret; + } + +#ifdef CONFIG_BF54x + /* Setup DMAC1 channel mux for NFC which shared with SDH */ + bfin_write_DMAC1_PERIMUX(bfin_read_DMAC1_PERIMUX() & ~1); + SSYNC(); +#endif + + set_dma_callback(CH_NFC, bf5xx_nand_dma_irq, info); + + /* Turn off the DMA channel first */ + disable_dma(CH_NFC); + return 0; +} + +static void bf5xx_nand_dma_remove(struct bf5xx_nand_info *info) +{ + /* Free NFC DMA channel */ + if (hardware_ecc) + free_dma(CH_NFC); +} + +/* + * BF5XX NFC hardware initialization + * - pin mux setup + * - clear interrupt status + */ +static int bf5xx_nand_hw_init(struct bf5xx_nand_info *info) +{ + int err = 0; + unsigned short val; + struct bf5xx_nand_platform *plat = info->platform; + + /* setup NFC_CTL register */ + dev_info(info->device, + "data_width=%d, wr_dly=%d, rd_dly=%d\n", + (plat->data_width ? 16 : 8), + plat->wr_dly, plat->rd_dly); + + val = (1 << NFC_PG_SIZE_OFFSET) | + (plat->data_width << NFC_NWIDTH_OFFSET) | + (plat->rd_dly << NFC_RDDLY_OFFSET) | + (plat->wr_dly << NFC_WRDLY_OFFSET); + dev_dbg(info->device, "NFC_CTL is 0x%04x\n", val); + + bfin_write_NFC_CTL(val); + SSYNC(); + + /* clear interrupt status */ + bfin_write_NFC_IRQMASK(0x0); + SSYNC(); + val = bfin_read_NFC_IRQSTAT(); + bfin_write_NFC_IRQSTAT(val); + SSYNC(); + + /* DMA initialization */ + if (bf5xx_nand_dma_init(info)) + err = -ENXIO; + + return err; +} + +/* + * Device management interface + */ +static int bf5xx_nand_add_partition(struct bf5xx_nand_info *info) +{ + struct mtd_info *mtd = &info->mtd; + struct mtd_partition *parts = info->platform->partitions; + int nr = info->platform->nr_partitions; + + return mtd_device_register(mtd, parts, nr); +} + +static int bf5xx_nand_remove(struct platform_device *pdev) +{ + struct bf5xx_nand_info *info = to_nand_info(pdev); + + /* first thing we need to do is release all our mtds + * and their partitions, then go through freeing the + * resources used + */ + nand_release(&info->mtd); + + peripheral_free_list(bfin_nfc_pin_req); + bf5xx_nand_dma_remove(info); + + return 0; +} + +static int bf5xx_nand_scan(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + int ret; + + ret = nand_scan_ident(mtd, 1, NULL); + if (ret) + return ret; + + if (hardware_ecc) { + /* + * for nand with page size > 512B, think it as several sections with 512B + */ + if (likely(mtd->writesize >= 512)) { + chip->ecc.size = 512; + chip->ecc.bytes = 6; + chip->ecc.strength = 2; + } else { + chip->ecc.size = 256; + chip->ecc.bytes = 3; + chip->ecc.strength = 1; + bfin_write_NFC_CTL(bfin_read_NFC_CTL() & ~(1 << NFC_PG_SIZE_OFFSET)); + SSYNC(); + } + } + + return nand_scan_tail(mtd); +} + +/* + * bf5xx_nand_probe + * + * called by device layer when it finds a device matching + * one our driver can handled. This code checks to see if + * it can allocate all necessary resources then calls the + * nand layer to look for devices + */ +static int bf5xx_nand_probe(struct platform_device *pdev) +{ + struct bf5xx_nand_platform *plat = to_nand_plat(pdev); + struct bf5xx_nand_info *info = NULL; + struct nand_chip *chip = NULL; + struct mtd_info *mtd = NULL; + int err = 0; + + dev_dbg(&pdev->dev, "(%p)\n", pdev); + + if (!plat) { + dev_err(&pdev->dev, "no platform specific information\n"); + return -EINVAL; + } + + if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) { + dev_err(&pdev->dev, "requesting Peripherals failed\n"); + return -EFAULT; + } + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (info == NULL) { + err = -ENOMEM; + goto out_err; + } + + platform_set_drvdata(pdev, info); + + spin_lock_init(&info->controller.lock); + init_waitqueue_head(&info->controller.wq); + + info->device = &pdev->dev; + info->platform = plat; + + /* initialise chip data struct */ + chip = &info->chip; + + if (plat->data_width) + chip->options |= NAND_BUSWIDTH_16; + + chip->options |= NAND_CACHEPRG | NAND_SKIP_BBTSCAN; + + chip->read_buf = (plat->data_width) ? + bf5xx_nand_read_buf16 : bf5xx_nand_read_buf; + chip->write_buf = (plat->data_width) ? + bf5xx_nand_write_buf16 : bf5xx_nand_write_buf; + + chip->read_byte = bf5xx_nand_read_byte; + + chip->cmd_ctrl = bf5xx_nand_hwcontrol; + chip->dev_ready = bf5xx_nand_devready; + + chip->priv = &info->mtd; + chip->controller = &info->controller; + + chip->IO_ADDR_R = (void __iomem *) NFC_READ; + chip->IO_ADDR_W = (void __iomem *) NFC_DATA_WR; + + chip->chip_delay = 0; + + /* initialise mtd info data struct */ + mtd = &info->mtd; + mtd->priv = chip; + mtd->owner = THIS_MODULE; + + /* initialise the hardware */ + err = bf5xx_nand_hw_init(info); + if (err) + goto out_err; + + /* setup hardware ECC data struct */ + if (hardware_ecc) { +#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC + chip->ecc.layout = &bootrom_ecclayout; +#endif + chip->read_buf = bf5xx_nand_dma_read_buf; + chip->write_buf = bf5xx_nand_dma_write_buf; + chip->ecc.calculate = bf5xx_nand_calculate_ecc; + chip->ecc.correct = bf5xx_nand_correct_data; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.hwctl = bf5xx_nand_enable_hwecc; + chip->ecc.read_page_raw = bf5xx_nand_read_page_raw; + chip->ecc.write_page_raw = bf5xx_nand_write_page_raw; + } else { + chip->ecc.mode = NAND_ECC_SOFT; + } + + /* scan hardware nand chip and setup mtd info data struct */ + if (bf5xx_nand_scan(mtd)) { + err = -ENXIO; + goto out_err_nand_scan; + } + +#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC + chip->badblockpos = 63; +#endif + + /* add NAND partition */ + bf5xx_nand_add_partition(info); + + dev_dbg(&pdev->dev, "initialised ok\n"); + return 0; + +out_err_nand_scan: + bf5xx_nand_dma_remove(info); +out_err: + peripheral_free_list(bfin_nfc_pin_req); + + return err; +} + +/* driver device registration */ +static struct platform_driver bf5xx_nand_driver = { + .probe = bf5xx_nand_probe, + .remove = bf5xx_nand_remove, + .driver = { + .name = DRV_NAME, + }, +}; + +module_platform_driver(bf5xx_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR(DRV_AUTHOR); +MODULE_DESCRIPTION(DRV_DESC); +MODULE_ALIAS("platform:" DRV_NAME); diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c new file mode 100644 index 000000000..9a0f45f1d --- /dev/null +++ b/drivers/mtd/nand/cafe_nand.c @@ -0,0 +1,869 @@ +/* + * Driver for One Laptop Per Child ‘CAFÉ’ controller, aka Marvell 88ALP01 + * + * The data sheet for this device can be found at: + * http://wiki.laptop.org/go/Datasheets + * + * Copyright © 2006 Red Hat, Inc. + * Copyright © 2006 David Woodhouse <dwmw2@infradead.org> + */ + +#define DEBUG + +#include <linux/device.h> +#undef DEBUG +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/rslib.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <asm/io.h> + +#define CAFE_NAND_CTRL1 0x00 +#define CAFE_NAND_CTRL2 0x04 +#define CAFE_NAND_CTRL3 0x08 +#define CAFE_NAND_STATUS 0x0c +#define CAFE_NAND_IRQ 0x10 +#define CAFE_NAND_IRQ_MASK 0x14 +#define CAFE_NAND_DATA_LEN 0x18 +#define CAFE_NAND_ADDR1 0x1c +#define CAFE_NAND_ADDR2 0x20 +#define CAFE_NAND_TIMING1 0x24 +#define CAFE_NAND_TIMING2 0x28 +#define CAFE_NAND_TIMING3 0x2c +#define CAFE_NAND_NONMEM 0x30 +#define CAFE_NAND_ECC_RESULT 0x3C +#define CAFE_NAND_DMA_CTRL 0x40 +#define CAFE_NAND_DMA_ADDR0 0x44 +#define CAFE_NAND_DMA_ADDR1 0x48 +#define CAFE_NAND_ECC_SYN01 0x50 +#define CAFE_NAND_ECC_SYN23 0x54 +#define CAFE_NAND_ECC_SYN45 0x58 +#define CAFE_NAND_ECC_SYN67 0x5c +#define CAFE_NAND_READ_DATA 0x1000 +#define CAFE_NAND_WRITE_DATA 0x2000 + +#define CAFE_GLOBAL_CTRL 0x3004 +#define CAFE_GLOBAL_IRQ 0x3008 +#define CAFE_GLOBAL_IRQ_MASK 0x300c +#define CAFE_NAND_RESET 0x3034 + +/* Missing from the datasheet: bit 19 of CTRL1 sets CE0 vs. CE1 */ +#define CTRL1_CHIPSELECT (1<<19) + +struct cafe_priv { + struct nand_chip nand; + struct pci_dev *pdev; + void __iomem *mmio; + struct rs_control *rs; + uint32_t ctl1; + uint32_t ctl2; + int datalen; + int nr_data; + int data_pos; + int page_addr; + dma_addr_t dmaaddr; + unsigned char *dmabuf; +}; + +static int usedma = 1; +module_param(usedma, int, 0644); + +static int skipbbt = 0; +module_param(skipbbt, int, 0644); + +static int debug = 0; +module_param(debug, int, 0644); + +static int regdebug = 0; +module_param(regdebug, int, 0644); + +static int checkecc = 1; +module_param(checkecc, int, 0644); + +static unsigned int numtimings; +static int timing[3]; +module_param_array(timing, int, &numtimings, 0644); + +static const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL }; + +/* Hrm. Why isn't this already conditional on something in the struct device? */ +#define cafe_dev_dbg(dev, args...) do { if (debug) dev_dbg(dev, ##args); } while(0) + +/* Make it easier to switch to PIO if we need to */ +#define cafe_readl(cafe, addr) readl((cafe)->mmio + CAFE_##addr) +#define cafe_writel(cafe, datum, addr) writel(datum, (cafe)->mmio + CAFE_##addr) + +static int cafe_device_ready(struct mtd_info *mtd) +{ + struct cafe_priv *cafe = mtd->priv; + int result = !!(cafe_readl(cafe, NAND_STATUS) & 0x40000000); + uint32_t irqs = cafe_readl(cafe, NAND_IRQ); + + cafe_writel(cafe, irqs, NAND_IRQ); + + cafe_dev_dbg(&cafe->pdev->dev, "NAND device is%s ready, IRQ %x (%x) (%x,%x)\n", + result?"":" not", irqs, cafe_readl(cafe, NAND_IRQ), + cafe_readl(cafe, GLOBAL_IRQ), cafe_readl(cafe, GLOBAL_IRQ_MASK)); + + return result; +} + + +static void cafe_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct cafe_priv *cafe = mtd->priv; + + if (usedma) + memcpy(cafe->dmabuf + cafe->datalen, buf, len); + else + memcpy_toio(cafe->mmio + CAFE_NAND_WRITE_DATA + cafe->datalen, buf, len); + + cafe->datalen += len; + + cafe_dev_dbg(&cafe->pdev->dev, "Copy 0x%x bytes to write buffer. datalen 0x%x\n", + len, cafe->datalen); +} + +static void cafe_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct cafe_priv *cafe = mtd->priv; + + if (usedma) + memcpy(buf, cafe->dmabuf + cafe->datalen, len); + else + memcpy_fromio(buf, cafe->mmio + CAFE_NAND_READ_DATA + cafe->datalen, len); + + cafe_dev_dbg(&cafe->pdev->dev, "Copy 0x%x bytes from position 0x%x in read buffer.\n", + len, cafe->datalen); + cafe->datalen += len; +} + +static uint8_t cafe_read_byte(struct mtd_info *mtd) +{ + struct cafe_priv *cafe = mtd->priv; + uint8_t d; + + cafe_read_buf(mtd, &d, 1); + cafe_dev_dbg(&cafe->pdev->dev, "Read %02x\n", d); + + return d; +} + +static void cafe_nand_cmdfunc(struct mtd_info *mtd, unsigned command, + int column, int page_addr) +{ + struct cafe_priv *cafe = mtd->priv; + int adrbytes = 0; + uint32_t ctl1; + uint32_t doneint = 0x80000000; + + cafe_dev_dbg(&cafe->pdev->dev, "cmdfunc %02x, 0x%x, 0x%x\n", + command, column, page_addr); + + if (command == NAND_CMD_ERASE2 || command == NAND_CMD_PAGEPROG) { + /* Second half of a command we already calculated */ + cafe_writel(cafe, cafe->ctl2 | 0x100 | command, NAND_CTRL2); + ctl1 = cafe->ctl1; + cafe->ctl2 &= ~(1<<30); + cafe_dev_dbg(&cafe->pdev->dev, "Continue command, ctl1 %08x, #data %d\n", + cafe->ctl1, cafe->nr_data); + goto do_command; + } + /* Reset ECC engine */ + cafe_writel(cafe, 0, NAND_CTRL2); + + /* Emulate NAND_CMD_READOOB on large-page chips */ + if (mtd->writesize > 512 && + command == NAND_CMD_READOOB) { + column += mtd->writesize; + command = NAND_CMD_READ0; + } + + /* FIXME: Do we need to send read command before sending data + for small-page chips, to position the buffer correctly? */ + + if (column != -1) { + cafe_writel(cafe, column, NAND_ADDR1); + adrbytes = 2; + if (page_addr != -1) + goto write_adr2; + } else if (page_addr != -1) { + cafe_writel(cafe, page_addr & 0xffff, NAND_ADDR1); + page_addr >>= 16; + write_adr2: + cafe_writel(cafe, page_addr, NAND_ADDR2); + adrbytes += 2; + if (mtd->size > mtd->writesize << 16) + adrbytes++; + } + + cafe->data_pos = cafe->datalen = 0; + + /* Set command valid bit, mask in the chip select bit */ + ctl1 = 0x80000000 | command | (cafe->ctl1 & CTRL1_CHIPSELECT); + + /* Set RD or WR bits as appropriate */ + if (command == NAND_CMD_READID || command == NAND_CMD_STATUS) { + ctl1 |= (1<<26); /* rd */ + /* Always 5 bytes, for now */ + cafe->datalen = 4; + /* And one address cycle -- even for STATUS, since the controller doesn't work without */ + adrbytes = 1; + } else if (command == NAND_CMD_READ0 || command == NAND_CMD_READ1 || + command == NAND_CMD_READOOB || command == NAND_CMD_RNDOUT) { + ctl1 |= 1<<26; /* rd */ + /* For now, assume just read to end of page */ + cafe->datalen = mtd->writesize + mtd->oobsize - column; + } else if (command == NAND_CMD_SEQIN) + ctl1 |= 1<<25; /* wr */ + + /* Set number of address bytes */ + if (adrbytes) + ctl1 |= ((adrbytes-1)|8) << 27; + + if (command == NAND_CMD_SEQIN || command == NAND_CMD_ERASE1) { + /* Ignore the first command of a pair; the hardware + deals with them both at once, later */ + cafe->ctl1 = ctl1; + cafe_dev_dbg(&cafe->pdev->dev, "Setup for delayed command, ctl1 %08x, dlen %x\n", + cafe->ctl1, cafe->datalen); + return; + } + /* RNDOUT and READ0 commands need a following byte */ + if (command == NAND_CMD_RNDOUT) + cafe_writel(cafe, cafe->ctl2 | 0x100 | NAND_CMD_RNDOUTSTART, NAND_CTRL2); + else if (command == NAND_CMD_READ0 && mtd->writesize > 512) + cafe_writel(cafe, cafe->ctl2 | 0x100 | NAND_CMD_READSTART, NAND_CTRL2); + + do_command: + cafe_dev_dbg(&cafe->pdev->dev, "dlen %x, ctl1 %x, ctl2 %x\n", + cafe->datalen, ctl1, cafe_readl(cafe, NAND_CTRL2)); + + /* NB: The datasheet lies -- we really should be subtracting 1 here */ + cafe_writel(cafe, cafe->datalen, NAND_DATA_LEN); + cafe_writel(cafe, 0x90000000, NAND_IRQ); + if (usedma && (ctl1 & (3<<25))) { + uint32_t dmactl = 0xc0000000 + cafe->datalen; + /* If WR or RD bits set, set up DMA */ + if (ctl1 & (1<<26)) { + /* It's a read */ + dmactl |= (1<<29); + /* ... so it's done when the DMA is done, not just + the command. */ + doneint = 0x10000000; + } + cafe_writel(cafe, dmactl, NAND_DMA_CTRL); + } + cafe->datalen = 0; + + if (unlikely(regdebug)) { + int i; + printk("About to write command %08x to register 0\n", ctl1); + for (i=4; i< 0x5c; i+=4) + printk("Register %x: %08x\n", i, readl(cafe->mmio + i)); + } + + cafe_writel(cafe, ctl1, NAND_CTRL1); + /* Apply this short delay always to ensure that we do wait tWB in + * any case on any machine. */ + ndelay(100); + + if (1) { + int c; + uint32_t irqs; + + for (c = 500000; c != 0; c--) { + irqs = cafe_readl(cafe, NAND_IRQ); + if (irqs & doneint) + break; + udelay(1); + if (!(c % 100000)) + cafe_dev_dbg(&cafe->pdev->dev, "Wait for ready, IRQ %x\n", irqs); + cpu_relax(); + } + cafe_writel(cafe, doneint, NAND_IRQ); + cafe_dev_dbg(&cafe->pdev->dev, "Command %x completed after %d usec, irqs %x (%x)\n", + command, 500000-c, irqs, cafe_readl(cafe, NAND_IRQ)); + } + + WARN_ON(cafe->ctl2 & (1<<30)); + + switch (command) { + + case NAND_CMD_CACHEDPROG: + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_RNDIN: + case NAND_CMD_STATUS: + case NAND_CMD_RNDOUT: + cafe_writel(cafe, cafe->ctl2, NAND_CTRL2); + return; + } + nand_wait_ready(mtd); + cafe_writel(cafe, cafe->ctl2, NAND_CTRL2); +} + +static void cafe_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct cafe_priv *cafe = mtd->priv; + + cafe_dev_dbg(&cafe->pdev->dev, "select_chip %d\n", chipnr); + + /* Mask the appropriate bit into the stored value of ctl1 + which will be used by cafe_nand_cmdfunc() */ + if (chipnr) + cafe->ctl1 |= CTRL1_CHIPSELECT; + else + cafe->ctl1 &= ~CTRL1_CHIPSELECT; +} + +static irqreturn_t cafe_nand_interrupt(int irq, void *id) +{ + struct mtd_info *mtd = id; + struct cafe_priv *cafe = mtd->priv; + uint32_t irqs = cafe_readl(cafe, NAND_IRQ); + cafe_writel(cafe, irqs & ~0x90000000, NAND_IRQ); + if (!irqs) + return IRQ_NONE; + + cafe_dev_dbg(&cafe->pdev->dev, "irq, bits %x (%x)\n", irqs, cafe_readl(cafe, NAND_IRQ)); + return IRQ_HANDLED; +} + +static void cafe_nand_bug(struct mtd_info *mtd) +{ + BUG(); +} + +static int cafe_nand_write_oob(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + int status = 0; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/* Don't use -- use nand_read_oob_std for now */ +static int cafe_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} +/** + * cafe_nand_read_page_syndrome - [REPLACEABLE] hardware ecc syndrome based page read + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller expects OOB data read to chip->oob_poi + * + * The hw generator calculates the error syndrome automatically. Therefore + * we need a special oob layout and handling. + */ +static int cafe_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct cafe_priv *cafe = mtd->priv; + unsigned int max_bitflips = 0; + + cafe_dev_dbg(&cafe->pdev->dev, "ECC result %08x SYN1,2 %08x\n", + cafe_readl(cafe, NAND_ECC_RESULT), + cafe_readl(cafe, NAND_ECC_SYN01)); + + chip->read_buf(mtd, buf, mtd->writesize); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (checkecc && cafe_readl(cafe, NAND_ECC_RESULT) & (1<<18)) { + unsigned short syn[8], pat[4]; + int pos[4]; + u8 *oob = chip->oob_poi; + int i, n; + + for (i=0; i<8; i+=2) { + uint32_t tmp = cafe_readl(cafe, NAND_ECC_SYN01 + (i*2)); + syn[i] = cafe->rs->index_of[tmp & 0xfff]; + syn[i+1] = cafe->rs->index_of[(tmp >> 16) & 0xfff]; + } + + n = decode_rs16(cafe->rs, NULL, NULL, 1367, syn, 0, pos, 0, + pat); + + for (i = 0; i < n; i++) { + int p = pos[i]; + + /* The 12-bit symbols are mapped to bytes here */ + + if (p > 1374) { + /* out of range */ + n = -1374; + } else if (p == 0) { + /* high four bits do not correspond to data */ + if (pat[i] > 0xff) + n = -2048; + else + buf[0] ^= pat[i]; + } else if (p == 1365) { + buf[2047] ^= pat[i] >> 4; + oob[0] ^= pat[i] << 4; + } else if (p > 1365) { + if ((p & 1) == 1) { + oob[3*p/2 - 2048] ^= pat[i] >> 4; + oob[3*p/2 - 2047] ^= pat[i] << 4; + } else { + oob[3*p/2 - 2049] ^= pat[i] >> 8; + oob[3*p/2 - 2048] ^= pat[i]; + } + } else if ((p & 1) == 1) { + buf[3*p/2] ^= pat[i] >> 4; + buf[3*p/2 + 1] ^= pat[i] << 4; + } else { + buf[3*p/2 - 1] ^= pat[i] >> 8; + buf[3*p/2] ^= pat[i]; + } + } + + if (n < 0) { + dev_dbg(&cafe->pdev->dev, "Failed to correct ECC at %08x\n", + cafe_readl(cafe, NAND_ADDR2) * 2048); + for (i = 0; i < 0x5c; i += 4) + printk("Register %x: %08x\n", i, readl(cafe->mmio + i)); + mtd->ecc_stats.failed++; + } else { + dev_dbg(&cafe->pdev->dev, "Corrected %d symbol errors\n", n); + mtd->ecc_stats.corrected += n; + max_bitflips = max_t(unsigned int, max_bitflips, n); + } + } + + return max_bitflips; +} + +static struct nand_ecclayout cafe_oobinfo_2048 = { + .eccbytes = 14, + .eccpos = { 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, + .oobfree = {{14, 50}} +}; + +/* Ick. The BBT code really ought to be able to work this bit out + for itself from the above, at least for the 2KiB case */ +static uint8_t cafe_bbt_pattern_2048[] = { 'B', 'b', 't', '0' }; +static uint8_t cafe_mirror_pattern_2048[] = { '1', 't', 'b', 'B' }; + +static uint8_t cafe_bbt_pattern_512[] = { 0xBB }; +static uint8_t cafe_mirror_pattern_512[] = { 0xBC }; + + +static struct nand_bbt_descr cafe_bbt_main_descr_2048 = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 14, + .len = 4, + .veroffs = 18, + .maxblocks = 4, + .pattern = cafe_bbt_pattern_2048 +}; + +static struct nand_bbt_descr cafe_bbt_mirror_descr_2048 = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 14, + .len = 4, + .veroffs = 18, + .maxblocks = 4, + .pattern = cafe_mirror_pattern_2048 +}; + +static struct nand_ecclayout cafe_oobinfo_512 = { + .eccbytes = 14, + .eccpos = { 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, + .oobfree = {{14, 2}} +}; + +static struct nand_bbt_descr cafe_bbt_main_descr_512 = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 14, + .len = 1, + .veroffs = 15, + .maxblocks = 4, + .pattern = cafe_bbt_pattern_512 +}; + +static struct nand_bbt_descr cafe_bbt_mirror_descr_512 = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 14, + .len = 1, + .veroffs = 15, + .maxblocks = 4, + .pattern = cafe_mirror_pattern_512 +}; + + +static int cafe_nand_write_page_lowlevel(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + struct cafe_priv *cafe = mtd->priv; + + chip->write_buf(mtd, buf, mtd->writesize); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + /* Set up ECC autogeneration */ + cafe->ctl2 |= (1<<30); + + return 0; +} + +static int cafe_nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + return 0; +} + +/* F_2[X]/(X**6+X+1) */ +static unsigned short gf64_mul(u8 a, u8 b) +{ + u8 c; + unsigned int i; + + c = 0; + for (i = 0; i < 6; i++) { + if (a & 1) + c ^= b; + a >>= 1; + b <<= 1; + if ((b & 0x40) != 0) + b ^= 0x43; + } + + return c; +} + +/* F_64[X]/(X**2+X+A**-1) with A the generator of F_64[X] */ +static u16 gf4096_mul(u16 a, u16 b) +{ + u8 ah, al, bh, bl, ch, cl; + + ah = a >> 6; + al = a & 0x3f; + bh = b >> 6; + bl = b & 0x3f; + + ch = gf64_mul(ah ^ al, bh ^ bl) ^ gf64_mul(al, bl); + cl = gf64_mul(gf64_mul(ah, bh), 0x21) ^ gf64_mul(al, bl); + + return (ch << 6) ^ cl; +} + +static int cafe_mul(int x) +{ + if (x == 0) + return 1; + return gf4096_mul(x, 0xe01); +} + +static int cafe_nand_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct mtd_info *mtd; + struct cafe_priv *cafe; + uint32_t ctrl; + int err = 0; + int old_dma; + struct nand_buffers *nbuf; + + /* Very old versions shared the same PCI ident for all three + functions on the chip. Verify the class too... */ + if ((pdev->class >> 8) != PCI_CLASS_MEMORY_FLASH) + return -ENODEV; + + err = pci_enable_device(pdev); + if (err) + return err; + + pci_set_master(pdev); + + mtd = kzalloc(sizeof(*mtd) + sizeof(struct cafe_priv), GFP_KERNEL); + if (!mtd) + return -ENOMEM; + cafe = (void *)(&mtd[1]); + + mtd->dev.parent = &pdev->dev; + mtd->priv = cafe; + mtd->owner = THIS_MODULE; + + cafe->pdev = pdev; + cafe->mmio = pci_iomap(pdev, 0, 0); + if (!cafe->mmio) { + dev_warn(&pdev->dev, "failed to iomap\n"); + err = -ENOMEM; + goto out_free_mtd; + } + + cafe->rs = init_rs_non_canonical(12, &cafe_mul, 0, 1, 8); + if (!cafe->rs) { + err = -ENOMEM; + goto out_ior; + } + + cafe->nand.cmdfunc = cafe_nand_cmdfunc; + cafe->nand.dev_ready = cafe_device_ready; + cafe->nand.read_byte = cafe_read_byte; + cafe->nand.read_buf = cafe_read_buf; + cafe->nand.write_buf = cafe_write_buf; + cafe->nand.select_chip = cafe_select_chip; + + cafe->nand.chip_delay = 0; + + /* Enable the following for a flash based bad block table */ + cafe->nand.bbt_options = NAND_BBT_USE_FLASH; + cafe->nand.options = NAND_OWN_BUFFERS; + + if (skipbbt) { + cafe->nand.options |= NAND_SKIP_BBTSCAN; + cafe->nand.block_bad = cafe_nand_block_bad; + } + + if (numtimings && numtimings != 3) { + dev_warn(&cafe->pdev->dev, "%d timing register values ignored; precisely three are required\n", numtimings); + } + + if (numtimings == 3) { + cafe_dev_dbg(&cafe->pdev->dev, "Using provided timings (%08x %08x %08x)\n", + timing[0], timing[1], timing[2]); + } else { + timing[0] = cafe_readl(cafe, NAND_TIMING1); + timing[1] = cafe_readl(cafe, NAND_TIMING2); + timing[2] = cafe_readl(cafe, NAND_TIMING3); + + if (timing[0] | timing[1] | timing[2]) { + cafe_dev_dbg(&cafe->pdev->dev, "Timing registers already set (%08x %08x %08x)\n", + timing[0], timing[1], timing[2]); + } else { + dev_warn(&cafe->pdev->dev, "Timing registers unset; using most conservative defaults\n"); + timing[0] = timing[1] = timing[2] = 0xffffffff; + } + } + + /* Start off by resetting the NAND controller completely */ + cafe_writel(cafe, 1, NAND_RESET); + cafe_writel(cafe, 0, NAND_RESET); + + cafe_writel(cafe, timing[0], NAND_TIMING1); + cafe_writel(cafe, timing[1], NAND_TIMING2); + cafe_writel(cafe, timing[2], NAND_TIMING3); + + cafe_writel(cafe, 0xffffffff, NAND_IRQ_MASK); + err = request_irq(pdev->irq, &cafe_nand_interrupt, IRQF_SHARED, + "CAFE NAND", mtd); + if (err) { + dev_warn(&pdev->dev, "Could not register IRQ %d\n", pdev->irq); + goto out_ior; + } + + /* Disable master reset, enable NAND clock */ + ctrl = cafe_readl(cafe, GLOBAL_CTRL); + ctrl &= 0xffffeff0; + ctrl |= 0x00007000; + cafe_writel(cafe, ctrl | 0x05, GLOBAL_CTRL); + cafe_writel(cafe, ctrl | 0x0a, GLOBAL_CTRL); + cafe_writel(cafe, 0, NAND_DMA_CTRL); + + cafe_writel(cafe, 0x7006, GLOBAL_CTRL); + cafe_writel(cafe, 0x700a, GLOBAL_CTRL); + + /* Enable NAND IRQ in global IRQ mask register */ + cafe_writel(cafe, 0x80000007, GLOBAL_IRQ_MASK); + cafe_dev_dbg(&cafe->pdev->dev, "Control %x, IRQ mask %x\n", + cafe_readl(cafe, GLOBAL_CTRL), + cafe_readl(cafe, GLOBAL_IRQ_MASK)); + + /* Do not use the DMA for the nand_scan_ident() */ + old_dma = usedma; + usedma = 0; + + /* Scan to find existence of the device */ + if (nand_scan_ident(mtd, 2, NULL)) { + err = -ENXIO; + goto out_irq; + } + + cafe->dmabuf = dma_alloc_coherent(&cafe->pdev->dev, + 2112 + sizeof(struct nand_buffers) + + mtd->writesize + mtd->oobsize, + &cafe->dmaaddr, GFP_KERNEL); + if (!cafe->dmabuf) { + err = -ENOMEM; + goto out_irq; + } + cafe->nand.buffers = nbuf = (void *)cafe->dmabuf + 2112; + + /* Set up DMA address */ + cafe_writel(cafe, cafe->dmaaddr & 0xffffffff, NAND_DMA_ADDR0); + if (sizeof(cafe->dmaaddr) > 4) + /* Shift in two parts to shut the compiler up */ + cafe_writel(cafe, (cafe->dmaaddr >> 16) >> 16, NAND_DMA_ADDR1); + else + cafe_writel(cafe, 0, NAND_DMA_ADDR1); + + cafe_dev_dbg(&cafe->pdev->dev, "Set DMA address to %x (virt %p)\n", + cafe_readl(cafe, NAND_DMA_ADDR0), cafe->dmabuf); + + /* this driver does not need the @ecccalc and @ecccode */ + nbuf->ecccalc = NULL; + nbuf->ecccode = NULL; + nbuf->databuf = (uint8_t *)(nbuf + 1); + + /* Restore the DMA flag */ + usedma = old_dma; + + cafe->ctl2 = 1<<27; /* Reed-Solomon ECC */ + if (mtd->writesize == 2048) + cafe->ctl2 |= 1<<29; /* 2KiB page size */ + + /* Set up ECC according to the type of chip we found */ + if (mtd->writesize == 2048) { + cafe->nand.ecc.layout = &cafe_oobinfo_2048; + cafe->nand.bbt_td = &cafe_bbt_main_descr_2048; + cafe->nand.bbt_md = &cafe_bbt_mirror_descr_2048; + } else if (mtd->writesize == 512) { + cafe->nand.ecc.layout = &cafe_oobinfo_512; + cafe->nand.bbt_td = &cafe_bbt_main_descr_512; + cafe->nand.bbt_md = &cafe_bbt_mirror_descr_512; + } else { + printk(KERN_WARNING "Unexpected NAND flash writesize %d. Aborting\n", + mtd->writesize); + goto out_free_dma; + } + cafe->nand.ecc.mode = NAND_ECC_HW_SYNDROME; + cafe->nand.ecc.size = mtd->writesize; + cafe->nand.ecc.bytes = 14; + cafe->nand.ecc.strength = 4; + cafe->nand.ecc.hwctl = (void *)cafe_nand_bug; + cafe->nand.ecc.calculate = (void *)cafe_nand_bug; + cafe->nand.ecc.correct = (void *)cafe_nand_bug; + cafe->nand.ecc.write_page = cafe_nand_write_page_lowlevel; + cafe->nand.ecc.write_oob = cafe_nand_write_oob; + cafe->nand.ecc.read_page = cafe_nand_read_page; + cafe->nand.ecc.read_oob = cafe_nand_read_oob; + + err = nand_scan_tail(mtd); + if (err) + goto out_free_dma; + + pci_set_drvdata(pdev, mtd); + + mtd->name = "cafe_nand"; + mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0); + + goto out; + + out_free_dma: + dma_free_coherent(&cafe->pdev->dev, + 2112 + sizeof(struct nand_buffers) + + mtd->writesize + mtd->oobsize, + cafe->dmabuf, cafe->dmaaddr); + out_irq: + /* Disable NAND IRQ in global IRQ mask register */ + cafe_writel(cafe, ~1 & cafe_readl(cafe, GLOBAL_IRQ_MASK), GLOBAL_IRQ_MASK); + free_irq(pdev->irq, mtd); + out_ior: + pci_iounmap(pdev, cafe->mmio); + out_free_mtd: + kfree(mtd); + out: + return err; +} + +static void cafe_nand_remove(struct pci_dev *pdev) +{ + struct mtd_info *mtd = pci_get_drvdata(pdev); + struct cafe_priv *cafe = mtd->priv; + + /* Disable NAND IRQ in global IRQ mask register */ + cafe_writel(cafe, ~1 & cafe_readl(cafe, GLOBAL_IRQ_MASK), GLOBAL_IRQ_MASK); + free_irq(pdev->irq, mtd); + nand_release(mtd); + free_rs(cafe->rs); + pci_iounmap(pdev, cafe->mmio); + dma_free_coherent(&cafe->pdev->dev, + 2112 + sizeof(struct nand_buffers) + + mtd->writesize + mtd->oobsize, + cafe->dmabuf, cafe->dmaaddr); + kfree(mtd); +} + +static const struct pci_device_id cafe_nand_tbl[] = { + { PCI_VENDOR_ID_MARVELL, PCI_DEVICE_ID_MARVELL_88ALP01_NAND, + PCI_ANY_ID, PCI_ANY_ID }, + { } +}; + +MODULE_DEVICE_TABLE(pci, cafe_nand_tbl); + +static int cafe_nand_resume(struct pci_dev *pdev) +{ + uint32_t ctrl; + struct mtd_info *mtd = pci_get_drvdata(pdev); + struct cafe_priv *cafe = mtd->priv; + + /* Start off by resetting the NAND controller completely */ + cafe_writel(cafe, 1, NAND_RESET); + cafe_writel(cafe, 0, NAND_RESET); + cafe_writel(cafe, 0xffffffff, NAND_IRQ_MASK); + + /* Restore timing configuration */ + cafe_writel(cafe, timing[0], NAND_TIMING1); + cafe_writel(cafe, timing[1], NAND_TIMING2); + cafe_writel(cafe, timing[2], NAND_TIMING3); + + /* Disable master reset, enable NAND clock */ + ctrl = cafe_readl(cafe, GLOBAL_CTRL); + ctrl &= 0xffffeff0; + ctrl |= 0x00007000; + cafe_writel(cafe, ctrl | 0x05, GLOBAL_CTRL); + cafe_writel(cafe, ctrl | 0x0a, GLOBAL_CTRL); + cafe_writel(cafe, 0, NAND_DMA_CTRL); + cafe_writel(cafe, 0x7006, GLOBAL_CTRL); + cafe_writel(cafe, 0x700a, GLOBAL_CTRL); + + /* Set up DMA address */ + cafe_writel(cafe, cafe->dmaaddr & 0xffffffff, NAND_DMA_ADDR0); + if (sizeof(cafe->dmaaddr) > 4) + /* Shift in two parts to shut the compiler up */ + cafe_writel(cafe, (cafe->dmaaddr >> 16) >> 16, NAND_DMA_ADDR1); + else + cafe_writel(cafe, 0, NAND_DMA_ADDR1); + + /* Enable NAND IRQ in global IRQ mask register */ + cafe_writel(cafe, 0x80000007, GLOBAL_IRQ_MASK); + return 0; +} + +static struct pci_driver cafe_nand_pci_driver = { + .name = "CAFÉ NAND", + .id_table = cafe_nand_tbl, + .probe = cafe_nand_probe, + .remove = cafe_nand_remove, + .resume = cafe_nand_resume, +}; + +module_pci_driver(cafe_nand_pci_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>"); +MODULE_DESCRIPTION("NAND flash driver for OLPC CAFÉ chip"); diff --git a/drivers/mtd/nand/cmx270_nand.c b/drivers/mtd/nand/cmx270_nand.c new file mode 100644 index 000000000..66ec95e6c --- /dev/null +++ b/drivers/mtd/nand/cmx270_nand.c @@ -0,0 +1,250 @@ +/* + * linux/drivers/mtd/nand/cmx270-nand.c + * + * Copyright (C) 2006 Compulab, Ltd. + * Mike Rapoport <mike@compulab.co.il> + * + * Derived from drivers/mtd/nand/h1910.c + * Copyright (C) 2002 Marius Gröger (mag@sysgo.de) + * Copyright (c) 2001 Thomas Gleixner (gleixner@autronix.de) + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Overview: + * This is a device driver for the NAND flash device found on the + * CM-X270 board. + */ + +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/slab.h> +#include <linux/gpio.h> +#include <linux/module.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/mach-types.h> + +#include <mach/pxa2xx-regs.h> + +#define GPIO_NAND_CS (11) +#define GPIO_NAND_RB (89) + +/* MTD structure for CM-X270 board */ +static struct mtd_info *cmx270_nand_mtd; + +/* remaped IO address of the device */ +static void __iomem *cmx270_nand_io; + +/* + * Define static partitions for flash device + */ +static struct mtd_partition partition_info[] = { + [0] = { + .name = "cmx270-0", + .offset = 0, + .size = MTDPART_SIZ_FULL + } +}; +#define NUM_PARTITIONS (ARRAY_SIZE(partition_info)) + +static u_char cmx270_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + + return (readl(this->IO_ADDR_R) >> 16); +} + +static void cmx270_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + + for (i=0; i<len; i++) + writel((*buf++ << 16), this->IO_ADDR_W); +} + +static void cmx270_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + + for (i=0; i<len; i++) + *buf++ = readl(this->IO_ADDR_R) >> 16; +} + +static inline void nand_cs_on(void) +{ + gpio_set_value(GPIO_NAND_CS, 0); +} + +static void nand_cs_off(void) +{ + dsb(); + + gpio_set_value(GPIO_NAND_CS, 1); +} + +/* + * hardware specific access to control-lines + */ +static void cmx270_hwcontrol(struct mtd_info *mtd, int dat, + unsigned int ctrl) +{ + struct nand_chip* this = mtd->priv; + unsigned int nandaddr = (unsigned int)this->IO_ADDR_W; + + dsb(); + + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_ALE ) + nandaddr |= (1 << 3); + else + nandaddr &= ~(1 << 3); + if ( ctrl & NAND_CLE ) + nandaddr |= (1 << 2); + else + nandaddr &= ~(1 << 2); + if ( ctrl & NAND_NCE ) + nand_cs_on(); + else + nand_cs_off(); + } + + dsb(); + this->IO_ADDR_W = (void __iomem*)nandaddr; + if (dat != NAND_CMD_NONE) + writel((dat << 16), this->IO_ADDR_W); + + dsb(); +} + +/* + * read device ready pin + */ +static int cmx270_device_ready(struct mtd_info *mtd) +{ + dsb(); + + return (gpio_get_value(GPIO_NAND_RB)); +} + +/* + * Main initialization routine + */ +static int __init cmx270_init(void) +{ + struct nand_chip *this; + int ret; + + if (!(machine_is_armcore() && cpu_is_pxa27x())) + return -ENODEV; + + ret = gpio_request(GPIO_NAND_CS, "NAND CS"); + if (ret) { + pr_warning("CM-X270: failed to request NAND CS gpio\n"); + return ret; + } + + gpio_direction_output(GPIO_NAND_CS, 1); + + ret = gpio_request(GPIO_NAND_RB, "NAND R/B"); + if (ret) { + pr_warning("CM-X270: failed to request NAND R/B gpio\n"); + goto err_gpio_request; + } + + gpio_direction_input(GPIO_NAND_RB); + + /* Allocate memory for MTD device structure and private data */ + cmx270_nand_mtd = kzalloc(sizeof(struct mtd_info) + + sizeof(struct nand_chip), + GFP_KERNEL); + if (!cmx270_nand_mtd) { + ret = -ENOMEM; + goto err_kzalloc; + } + + cmx270_nand_io = ioremap(PXA_CS1_PHYS, 12); + if (!cmx270_nand_io) { + pr_debug("Unable to ioremap NAND device\n"); + ret = -EINVAL; + goto err_ioremap; + } + + /* Get pointer to private data */ + this = (struct nand_chip *)(&cmx270_nand_mtd[1]); + + /* Link the private data with the MTD structure */ + cmx270_nand_mtd->owner = THIS_MODULE; + cmx270_nand_mtd->priv = this; + + /* insert callbacks */ + this->IO_ADDR_R = cmx270_nand_io; + this->IO_ADDR_W = cmx270_nand_io; + this->cmd_ctrl = cmx270_hwcontrol; + this->dev_ready = cmx270_device_ready; + + /* 15 us command delay time */ + this->chip_delay = 20; + this->ecc.mode = NAND_ECC_SOFT; + + /* read/write functions */ + this->read_byte = cmx270_read_byte; + this->read_buf = cmx270_read_buf; + this->write_buf = cmx270_write_buf; + + /* Scan to find existence of the device */ + if (nand_scan (cmx270_nand_mtd, 1)) { + pr_notice("No NAND device\n"); + ret = -ENXIO; + goto err_scan; + } + + /* Register the partitions */ + ret = mtd_device_parse_register(cmx270_nand_mtd, NULL, NULL, + partition_info, NUM_PARTITIONS); + if (ret) + goto err_scan; + + /* Return happy */ + return 0; + +err_scan: + iounmap(cmx270_nand_io); +err_ioremap: + kfree(cmx270_nand_mtd); +err_kzalloc: + gpio_free(GPIO_NAND_RB); +err_gpio_request: + gpio_free(GPIO_NAND_CS); + + return ret; + +} +module_init(cmx270_init); + +/* + * Clean up routine + */ +static void __exit cmx270_cleanup(void) +{ + /* Release resources, unregister device */ + nand_release(cmx270_nand_mtd); + + gpio_free(GPIO_NAND_RB); + gpio_free(GPIO_NAND_CS); + + iounmap(cmx270_nand_io); + + /* Free the MTD device structure */ + kfree (cmx270_nand_mtd); +} +module_exit(cmx270_cleanup); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Mike Rapoport <mike@compulab.co.il>"); +MODULE_DESCRIPTION("NAND flash driver for Compulab CM-X270 Module"); diff --git a/drivers/mtd/nand/cs553x_nand.c b/drivers/mtd/nand/cs553x_nand.c new file mode 100644 index 000000000..88109d375 --- /dev/null +++ b/drivers/mtd/nand/cs553x_nand.c @@ -0,0 +1,354 @@ +/* + * drivers/mtd/nand/cs553x_nand.c + * + * (C) 2005, 2006 Red Hat Inc. + * + * Author: David Woodhouse <dwmw2@infradead.org> + * Tom Sylla <tom.sylla@amd.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Overview: + * This is a device driver for the NAND flash controller found on + * the AMD CS5535/CS5536 companion chipsets for the Geode processor. + * mtd-id for command line partitioning is cs553x_nand_cs[0-3] + * where 0-3 reflects the chip select for NAND. + * + */ + +#include <linux/kernel.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/msr.h> +#include <asm/io.h> + +#define NR_CS553X_CONTROLLERS 4 + +#define MSR_DIVIL_GLD_CAP 0x51400000 /* DIVIL capabilitiies */ +#define CAP_CS5535 0x2df000ULL +#define CAP_CS5536 0x5df500ULL + +/* NAND Timing MSRs */ +#define MSR_NANDF_DATA 0x5140001b /* NAND Flash Data Timing MSR */ +#define MSR_NANDF_CTL 0x5140001c /* NAND Flash Control Timing */ +#define MSR_NANDF_RSVD 0x5140001d /* Reserved */ + +/* NAND BAR MSRs */ +#define MSR_DIVIL_LBAR_FLSH0 0x51400010 /* Flash Chip Select 0 */ +#define MSR_DIVIL_LBAR_FLSH1 0x51400011 /* Flash Chip Select 1 */ +#define MSR_DIVIL_LBAR_FLSH2 0x51400012 /* Flash Chip Select 2 */ +#define MSR_DIVIL_LBAR_FLSH3 0x51400013 /* Flash Chip Select 3 */ + /* Each made up of... */ +#define FLSH_LBAR_EN (1ULL<<32) +#define FLSH_NOR_NAND (1ULL<<33) /* 1 for NAND */ +#define FLSH_MEM_IO (1ULL<<34) /* 1 for MMIO */ + /* I/O BARs have BASE_ADDR in bits 15:4, IO_MASK in 47:36 */ + /* MMIO BARs have BASE_ADDR in bits 31:12, MEM_MASK in 63:44 */ + +/* Pin function selection MSR (IDE vs. flash on the IDE pins) */ +#define MSR_DIVIL_BALL_OPTS 0x51400015 +#define PIN_OPT_IDE (1<<0) /* 0 for flash, 1 for IDE */ + +/* Registers within the NAND flash controller BAR -- memory mapped */ +#define MM_NAND_DATA 0x00 /* 0 to 0x7ff, in fact */ +#define MM_NAND_CTL 0x800 /* Any even address 0x800-0x80e */ +#define MM_NAND_IO 0x801 /* Any odd address 0x801-0x80f */ +#define MM_NAND_STS 0x810 +#define MM_NAND_ECC_LSB 0x811 +#define MM_NAND_ECC_MSB 0x812 +#define MM_NAND_ECC_COL 0x813 +#define MM_NAND_LAC 0x814 +#define MM_NAND_ECC_CTL 0x815 + +/* Registers within the NAND flash controller BAR -- I/O mapped */ +#define IO_NAND_DATA 0x00 /* 0 to 3, in fact */ +#define IO_NAND_CTL 0x04 +#define IO_NAND_IO 0x05 +#define IO_NAND_STS 0x06 +#define IO_NAND_ECC_CTL 0x08 +#define IO_NAND_ECC_LSB 0x09 +#define IO_NAND_ECC_MSB 0x0a +#define IO_NAND_ECC_COL 0x0b +#define IO_NAND_LAC 0x0c + +#define CS_NAND_CTL_DIST_EN (1<<4) /* Enable NAND Distract interrupt */ +#define CS_NAND_CTL_RDY_INT_MASK (1<<3) /* Enable RDY/BUSY# interrupt */ +#define CS_NAND_CTL_ALE (1<<2) +#define CS_NAND_CTL_CLE (1<<1) +#define CS_NAND_CTL_CE (1<<0) /* Keep low; 1 to reset */ + +#define CS_NAND_STS_FLASH_RDY (1<<3) +#define CS_NAND_CTLR_BUSY (1<<2) +#define CS_NAND_CMD_COMP (1<<1) +#define CS_NAND_DIST_ST (1<<0) + +#define CS_NAND_ECC_PARITY (1<<2) +#define CS_NAND_ECC_CLRECC (1<<1) +#define CS_NAND_ECC_ENECC (1<<0) + +static void cs553x_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + + while (unlikely(len > 0x800)) { + memcpy_fromio(buf, this->IO_ADDR_R, 0x800); + buf += 0x800; + len -= 0x800; + } + memcpy_fromio(buf, this->IO_ADDR_R, len); +} + +static void cs553x_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + + while (unlikely(len > 0x800)) { + memcpy_toio(this->IO_ADDR_R, buf, 0x800); + buf += 0x800; + len -= 0x800; + } + memcpy_toio(this->IO_ADDR_R, buf, len); +} + +static unsigned char cs553x_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + return readb(this->IO_ADDR_R); +} + +static void cs553x_write_byte(struct mtd_info *mtd, u_char byte) +{ + struct nand_chip *this = mtd->priv; + int i = 100000; + + while (i && readb(this->IO_ADDR_R + MM_NAND_STS) & CS_NAND_CTLR_BUSY) { + udelay(1); + i--; + } + writeb(byte, this->IO_ADDR_W + 0x801); +} + +static void cs553x_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *this = mtd->priv; + void __iomem *mmio_base = this->IO_ADDR_R; + if (ctrl & NAND_CTRL_CHANGE) { + unsigned char ctl = (ctrl & ~NAND_CTRL_CHANGE ) ^ 0x01; + writeb(ctl, mmio_base + MM_NAND_CTL); + } + if (cmd != NAND_CMD_NONE) + cs553x_write_byte(mtd, cmd); +} + +static int cs553x_device_ready(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + void __iomem *mmio_base = this->IO_ADDR_R; + unsigned char foo = readb(mmio_base + MM_NAND_STS); + + return (foo & CS_NAND_STS_FLASH_RDY) && !(foo & CS_NAND_CTLR_BUSY); +} + +static void cs_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct nand_chip *this = mtd->priv; + void __iomem *mmio_base = this->IO_ADDR_R; + + writeb(0x07, mmio_base + MM_NAND_ECC_CTL); +} + +static int cs_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code) +{ + uint32_t ecc; + struct nand_chip *this = mtd->priv; + void __iomem *mmio_base = this->IO_ADDR_R; + + ecc = readl(mmio_base + MM_NAND_STS); + + ecc_code[1] = ecc >> 8; + ecc_code[0] = ecc >> 16; + ecc_code[2] = ecc >> 24; + return 0; +} + +static struct mtd_info *cs553x_mtd[4]; + +static int __init cs553x_init_one(int cs, int mmio, unsigned long adr) +{ + int err = 0; + struct nand_chip *this; + struct mtd_info *new_mtd; + + printk(KERN_NOTICE "Probing CS553x NAND controller CS#%d at %sIO 0x%08lx\n", cs, mmio?"MM":"P", adr); + + if (!mmio) { + printk(KERN_NOTICE "PIO mode not yet implemented for CS553X NAND controller\n"); + return -ENXIO; + } + + /* Allocate memory for MTD device structure and private data */ + new_mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL); + if (!new_mtd) { + err = -ENOMEM; + goto out; + } + + /* Get pointer to private data */ + this = (struct nand_chip *)(&new_mtd[1]); + + /* Link the private data with the MTD structure */ + new_mtd->priv = this; + new_mtd->owner = THIS_MODULE; + + /* map physical address */ + this->IO_ADDR_R = this->IO_ADDR_W = ioremap(adr, 4096); + if (!this->IO_ADDR_R) { + printk(KERN_WARNING "ioremap cs553x NAND @0x%08lx failed\n", adr); + err = -EIO; + goto out_mtd; + } + + this->cmd_ctrl = cs553x_hwcontrol; + this->dev_ready = cs553x_device_ready; + this->read_byte = cs553x_read_byte; + this->read_buf = cs553x_read_buf; + this->write_buf = cs553x_write_buf; + + this->chip_delay = 0; + + this->ecc.mode = NAND_ECC_HW; + this->ecc.size = 256; + this->ecc.bytes = 3; + this->ecc.hwctl = cs_enable_hwecc; + this->ecc.calculate = cs_calculate_ecc; + this->ecc.correct = nand_correct_data; + this->ecc.strength = 1; + + /* Enable the following for a flash based bad block table */ + this->bbt_options = NAND_BBT_USE_FLASH; + + /* Scan to find existence of the device */ + if (nand_scan(new_mtd, 1)) { + err = -ENXIO; + goto out_ior; + } + + new_mtd->name = kasprintf(GFP_KERNEL, "cs553x_nand_cs%d", cs); + + cs553x_mtd[cs] = new_mtd; + goto out; + +out_ior: + iounmap(this->IO_ADDR_R); +out_mtd: + kfree(new_mtd); +out: + return err; +} + +static int is_geode(void) +{ + /* These are the CPUs which will have a CS553[56] companion chip */ + if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD && + boot_cpu_data.x86 == 5 && + boot_cpu_data.x86_model == 10) + return 1; /* Geode LX */ + + if ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC || + boot_cpu_data.x86_vendor == X86_VENDOR_CYRIX) && + boot_cpu_data.x86 == 5 && + boot_cpu_data.x86_model == 5) + return 1; /* Geode GX (née GX2) */ + + return 0; +} + +static int __init cs553x_init(void) +{ + int err = -ENXIO; + int i; + uint64_t val; + + /* If the CPU isn't a Geode GX or LX, abort */ + if (!is_geode()) + return -ENXIO; + + /* If it doesn't have the CS553[56], abort */ + rdmsrl(MSR_DIVIL_GLD_CAP, val); + val &= ~0xFFULL; + if (val != CAP_CS5535 && val != CAP_CS5536) + return -ENXIO; + + /* If it doesn't have the NAND controller enabled, abort */ + rdmsrl(MSR_DIVIL_BALL_OPTS, val); + if (val & PIN_OPT_IDE) { + printk(KERN_INFO "CS553x NAND controller: Flash I/O not enabled in MSR_DIVIL_BALL_OPTS.\n"); + return -ENXIO; + } + + for (i = 0; i < NR_CS553X_CONTROLLERS; i++) { + rdmsrl(MSR_DIVIL_LBAR_FLSH0 + i, val); + + if ((val & (FLSH_LBAR_EN|FLSH_NOR_NAND)) == (FLSH_LBAR_EN|FLSH_NOR_NAND)) + err = cs553x_init_one(i, !!(val & FLSH_MEM_IO), val & 0xFFFFFFFF); + } + + /* Register all devices together here. This means we can easily hack it to + do mtdconcat etc. if we want to. */ + for (i = 0; i < NR_CS553X_CONTROLLERS; i++) { + if (cs553x_mtd[i]) { + /* If any devices registered, return success. Else the last error. */ + mtd_device_parse_register(cs553x_mtd[i], NULL, NULL, + NULL, 0); + err = 0; + } + } + + return err; +} + +module_init(cs553x_init); + +static void __exit cs553x_cleanup(void) +{ + int i; + + for (i = 0; i < NR_CS553X_CONTROLLERS; i++) { + struct mtd_info *mtd = cs553x_mtd[i]; + struct nand_chip *this; + void __iomem *mmio_base; + + if (!mtd) + continue; + + this = cs553x_mtd[i]->priv; + mmio_base = this->IO_ADDR_R; + + /* Release resources, unregister device */ + nand_release(cs553x_mtd[i]); + kfree(cs553x_mtd[i]->name); + cs553x_mtd[i] = NULL; + + /* unmap physical address */ + iounmap(mmio_base); + + /* Free the MTD device structure */ + kfree(mtd); + } +} + +module_exit(cs553x_cleanup); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>"); +MODULE_DESCRIPTION("NAND controller driver for AMD CS5535/CS5536 companion chip"); diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c new file mode 100644 index 000000000..feb6d18de --- /dev/null +++ b/drivers/mtd/nand/davinci_nand.c @@ -0,0 +1,883 @@ +/* + * davinci_nand.c - NAND Flash Driver for DaVinci family chips + * + * Copyright © 2006 Texas Instruments. + * + * Port to 2.6.23 Copyright © 2008 by: + * Sander Huijsen <Shuijsen@optelecom-nkf.com> + * Troy Kisky <troy.kisky@boundarydevices.com> + * Dirk Behme <Dirk.Behme@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/slab.h> +#include <linux/of_device.h> +#include <linux/of.h> +#include <linux/of_mtd.h> + +#include <linux/platform_data/mtd-davinci.h> +#include <linux/platform_data/mtd-davinci-aemif.h> + +/* + * This is a device driver for the NAND flash controller found on the + * various DaVinci family chips. It handles up to four SoC chipselects, + * and some flavors of secondary chipselect (e.g. based on A12) as used + * with multichip packages. + * + * The 1-bit ECC hardware is supported, as well as the newer 4-bit ECC + * available on chips like the DM355 and OMAP-L137 and needed with the + * more error-prone MLC NAND chips. + * + * This driver assumes EM_WAIT connects all the NAND devices' RDY/nBUSY + * outputs in a "wire-AND" configuration, with no per-chip signals. + */ +struct davinci_nand_info { + struct mtd_info mtd; + struct nand_chip chip; + struct nand_ecclayout ecclayout; + + struct device *dev; + struct clk *clk; + + bool is_readmode; + + void __iomem *base; + void __iomem *vaddr; + + uint32_t ioaddr; + uint32_t current_cs; + + uint32_t mask_chipsel; + uint32_t mask_ale; + uint32_t mask_cle; + + uint32_t core_chipsel; + + struct davinci_aemif_timing *timing; +}; + +static DEFINE_SPINLOCK(davinci_nand_lock); +static bool ecc4_busy; + +#define to_davinci_nand(m) container_of(m, struct davinci_nand_info, mtd) + + +static inline unsigned int davinci_nand_readl(struct davinci_nand_info *info, + int offset) +{ + return __raw_readl(info->base + offset); +} + +static inline void davinci_nand_writel(struct davinci_nand_info *info, + int offset, unsigned long value) +{ + __raw_writel(value, info->base + offset); +} + +/*----------------------------------------------------------------------*/ + +/* + * Access to hardware control lines: ALE, CLE, secondary chipselect. + */ + +static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + uint32_t addr = info->current_cs; + struct nand_chip *nand = mtd->priv; + + /* Did the control lines change? */ + if (ctrl & NAND_CTRL_CHANGE) { + if ((ctrl & NAND_CTRL_CLE) == NAND_CTRL_CLE) + addr |= info->mask_cle; + else if ((ctrl & NAND_CTRL_ALE) == NAND_CTRL_ALE) + addr |= info->mask_ale; + + nand->IO_ADDR_W = (void __iomem __force *)addr; + } + + if (cmd != NAND_CMD_NONE) + iowrite8(cmd, nand->IO_ADDR_W); +} + +static void nand_davinci_select_chip(struct mtd_info *mtd, int chip) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + uint32_t addr = info->ioaddr; + + /* maybe kick in a second chipselect */ + if (chip > 0) + addr |= info->mask_chipsel; + info->current_cs = addr; + + info->chip.IO_ADDR_W = (void __iomem __force *)addr; + info->chip.IO_ADDR_R = info->chip.IO_ADDR_W; +} + +/*----------------------------------------------------------------------*/ + +/* + * 1-bit hardware ECC ... context maintained for each core chipselect + */ + +static inline uint32_t nand_davinci_readecc_1bit(struct mtd_info *mtd) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + + return davinci_nand_readl(info, NANDF1ECC_OFFSET + + 4 * info->core_chipsel); +} + +static void nand_davinci_hwctl_1bit(struct mtd_info *mtd, int mode) +{ + struct davinci_nand_info *info; + uint32_t nandcfr; + unsigned long flags; + + info = to_davinci_nand(mtd); + + /* Reset ECC hardware */ + nand_davinci_readecc_1bit(mtd); + + spin_lock_irqsave(&davinci_nand_lock, flags); + + /* Restart ECC hardware */ + nandcfr = davinci_nand_readl(info, NANDFCR_OFFSET); + nandcfr |= BIT(8 + info->core_chipsel); + davinci_nand_writel(info, NANDFCR_OFFSET, nandcfr); + + spin_unlock_irqrestore(&davinci_nand_lock, flags); +} + +/* + * Read hardware ECC value and pack into three bytes + */ +static int nand_davinci_calculate_1bit(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_code) +{ + unsigned int ecc_val = nand_davinci_readecc_1bit(mtd); + unsigned int ecc24 = (ecc_val & 0x0fff) | ((ecc_val & 0x0fff0000) >> 4); + + /* invert so that erased block ecc is correct */ + ecc24 = ~ecc24; + ecc_code[0] = (u_char)(ecc24); + ecc_code[1] = (u_char)(ecc24 >> 8); + ecc_code[2] = (u_char)(ecc24 >> 16); + + return 0; +} + +static int nand_davinci_correct_1bit(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct nand_chip *chip = mtd->priv; + uint32_t eccNand = read_ecc[0] | (read_ecc[1] << 8) | + (read_ecc[2] << 16); + uint32_t eccCalc = calc_ecc[0] | (calc_ecc[1] << 8) | + (calc_ecc[2] << 16); + uint32_t diff = eccCalc ^ eccNand; + + if (diff) { + if ((((diff >> 12) ^ diff) & 0xfff) == 0xfff) { + /* Correctable error */ + if ((diff >> (12 + 3)) < chip->ecc.size) { + dat[diff >> (12 + 3)] ^= BIT((diff >> 12) & 7); + return 1; + } else { + return -1; + } + } else if (!(diff & (diff - 1))) { + /* Single bit ECC error in the ECC itself, + * nothing to fix */ + return 1; + } else { + /* Uncorrectable error */ + return -1; + } + + } + return 0; +} + +/*----------------------------------------------------------------------*/ + +/* + * 4-bit hardware ECC ... context maintained over entire AEMIF + * + * This is a syndrome engine, but we avoid NAND_ECC_HW_SYNDROME + * since that forces use of a problematic "infix OOB" layout. + * Among other things, it trashes manufacturer bad block markers. + * Also, and specific to this hardware, it ECC-protects the "prepad" + * in the OOB ... while having ECC protection for parts of OOB would + * seem useful, the current MTD stack sometimes wants to update the + * OOB without recomputing ECC. + */ + +static void nand_davinci_hwctl_4bit(struct mtd_info *mtd, int mode) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + unsigned long flags; + u32 val; + + spin_lock_irqsave(&davinci_nand_lock, flags); + + /* Start 4-bit ECC calculation for read/write */ + val = davinci_nand_readl(info, NANDFCR_OFFSET); + val &= ~(0x03 << 4); + val |= (info->core_chipsel << 4) | BIT(12); + davinci_nand_writel(info, NANDFCR_OFFSET, val); + + info->is_readmode = (mode == NAND_ECC_READ); + + spin_unlock_irqrestore(&davinci_nand_lock, flags); +} + +/* Read raw ECC code after writing to NAND. */ +static void +nand_davinci_readecc_4bit(struct davinci_nand_info *info, u32 code[4]) +{ + const u32 mask = 0x03ff03ff; + + code[0] = davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET) & mask; + code[1] = davinci_nand_readl(info, NAND_4BIT_ECC2_OFFSET) & mask; + code[2] = davinci_nand_readl(info, NAND_4BIT_ECC3_OFFSET) & mask; + code[3] = davinci_nand_readl(info, NAND_4BIT_ECC4_OFFSET) & mask; +} + +/* Terminate read ECC; or return ECC (as bytes) of data written to NAND. */ +static int nand_davinci_calculate_4bit(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_code) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + u32 raw_ecc[4], *p; + unsigned i; + + /* After a read, terminate ECC calculation by a dummy read + * of some 4-bit ECC register. ECC covers everything that + * was read; correct() just uses the hardware state, so + * ecc_code is not needed. + */ + if (info->is_readmode) { + davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET); + return 0; + } + + /* Pack eight raw 10-bit ecc values into ten bytes, making + * two passes which each convert four values (in upper and + * lower halves of two 32-bit words) into five bytes. The + * ROM boot loader uses this same packing scheme. + */ + nand_davinci_readecc_4bit(info, raw_ecc); + for (i = 0, p = raw_ecc; i < 2; i++, p += 2) { + *ecc_code++ = p[0] & 0xff; + *ecc_code++ = ((p[0] >> 8) & 0x03) | ((p[0] >> 14) & 0xfc); + *ecc_code++ = ((p[0] >> 22) & 0x0f) | ((p[1] << 4) & 0xf0); + *ecc_code++ = ((p[1] >> 4) & 0x3f) | ((p[1] >> 10) & 0xc0); + *ecc_code++ = (p[1] >> 18) & 0xff; + } + + return 0; +} + +/* Correct up to 4 bits in data we just read, using state left in the + * hardware plus the ecc_code computed when it was first written. + */ +static int nand_davinci_correct_4bit(struct mtd_info *mtd, + u_char *data, u_char *ecc_code, u_char *null) +{ + int i; + struct davinci_nand_info *info = to_davinci_nand(mtd); + unsigned short ecc10[8]; + unsigned short *ecc16; + u32 syndrome[4]; + u32 ecc_state; + unsigned num_errors, corrected; + unsigned long timeo; + + /* All bytes 0xff? It's an erased page; ignore its ECC. */ + for (i = 0; i < 10; i++) { + if (ecc_code[i] != 0xff) + goto compare; + } + return 0; + +compare: + /* Unpack ten bytes into eight 10 bit values. We know we're + * little-endian, and use type punning for less shifting/masking. + */ + if (WARN_ON(0x01 & (unsigned) ecc_code)) + return -EINVAL; + ecc16 = (unsigned short *)ecc_code; + + ecc10[0] = (ecc16[0] >> 0) & 0x3ff; + ecc10[1] = ((ecc16[0] >> 10) & 0x3f) | ((ecc16[1] << 6) & 0x3c0); + ecc10[2] = (ecc16[1] >> 4) & 0x3ff; + ecc10[3] = ((ecc16[1] >> 14) & 0x3) | ((ecc16[2] << 2) & 0x3fc); + ecc10[4] = (ecc16[2] >> 8) | ((ecc16[3] << 8) & 0x300); + ecc10[5] = (ecc16[3] >> 2) & 0x3ff; + ecc10[6] = ((ecc16[3] >> 12) & 0xf) | ((ecc16[4] << 4) & 0x3f0); + ecc10[7] = (ecc16[4] >> 6) & 0x3ff; + + /* Tell ECC controller about the expected ECC codes. */ + for (i = 7; i >= 0; i--) + davinci_nand_writel(info, NAND_4BIT_ECC_LOAD_OFFSET, ecc10[i]); + + /* Allow time for syndrome calculation ... then read it. + * A syndrome of all zeroes 0 means no detected errors. + */ + davinci_nand_readl(info, NANDFSR_OFFSET); + nand_davinci_readecc_4bit(info, syndrome); + if (!(syndrome[0] | syndrome[1] | syndrome[2] | syndrome[3])) + return 0; + + /* + * Clear any previous address calculation by doing a dummy read of an + * error address register. + */ + davinci_nand_readl(info, NAND_ERR_ADD1_OFFSET); + + /* Start address calculation, and wait for it to complete. + * We _could_ start reading more data while this is working, + * to speed up the overall page read. + */ + davinci_nand_writel(info, NANDFCR_OFFSET, + davinci_nand_readl(info, NANDFCR_OFFSET) | BIT(13)); + + /* + * ECC_STATE field reads 0x3 (Error correction complete) immediately + * after setting the 4BITECC_ADD_CALC_START bit. So if you immediately + * begin trying to poll for the state, you may fall right out of your + * loop without any of the correction calculations having taken place. + * The recommendation from the hardware team is to initially delay as + * long as ECC_STATE reads less than 4. After that, ECC HW has entered + * correction state. + */ + timeo = jiffies + usecs_to_jiffies(100); + do { + ecc_state = (davinci_nand_readl(info, + NANDFSR_OFFSET) >> 8) & 0x0f; + cpu_relax(); + } while ((ecc_state < 4) && time_before(jiffies, timeo)); + + for (;;) { + u32 fsr = davinci_nand_readl(info, NANDFSR_OFFSET); + + switch ((fsr >> 8) & 0x0f) { + case 0: /* no error, should not happen */ + davinci_nand_readl(info, NAND_ERR_ERRVAL1_OFFSET); + return 0; + case 1: /* five or more errors detected */ + davinci_nand_readl(info, NAND_ERR_ERRVAL1_OFFSET); + return -EIO; + case 2: /* error addresses computed */ + case 3: + num_errors = 1 + ((fsr >> 16) & 0x03); + goto correct; + default: /* still working on it */ + cpu_relax(); + continue; + } + } + +correct: + /* correct each error */ + for (i = 0, corrected = 0; i < num_errors; i++) { + int error_address, error_value; + + if (i > 1) { + error_address = davinci_nand_readl(info, + NAND_ERR_ADD2_OFFSET); + error_value = davinci_nand_readl(info, + NAND_ERR_ERRVAL2_OFFSET); + } else { + error_address = davinci_nand_readl(info, + NAND_ERR_ADD1_OFFSET); + error_value = davinci_nand_readl(info, + NAND_ERR_ERRVAL1_OFFSET); + } + + if (i & 1) { + error_address >>= 16; + error_value >>= 16; + } + error_address &= 0x3ff; + error_address = (512 + 7) - error_address; + + if (error_address < 512) { + data[error_address] ^= error_value; + corrected++; + } + } + + return corrected; +} + +/*----------------------------------------------------------------------*/ + +/* + * NOTE: NAND boot requires ALE == EM_A[1], CLE == EM_A[2], so that's + * how these chips are normally wired. This translates to both 8 and 16 + * bit busses using ALE == BIT(3) in byte addresses, and CLE == BIT(4). + * + * For now we assume that configuration, or any other one which ignores + * the two LSBs for NAND access ... so we can issue 32-bit reads/writes + * and have that transparently morphed into multiple NAND operations. + */ +static void nand_davinci_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0) + ioread32_rep(chip->IO_ADDR_R, buf, len >> 2); + else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0) + ioread16_rep(chip->IO_ADDR_R, buf, len >> 1); + else + ioread8_rep(chip->IO_ADDR_R, buf, len); +} + +static void nand_davinci_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0) + iowrite32_rep(chip->IO_ADDR_R, buf, len >> 2); + else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0) + iowrite16_rep(chip->IO_ADDR_R, buf, len >> 1); + else + iowrite8_rep(chip->IO_ADDR_R, buf, len); +} + +/* + * Check hardware register for wait status. Returns 1 if device is ready, + * 0 if it is still busy. + */ +static int nand_davinci_dev_ready(struct mtd_info *mtd) +{ + struct davinci_nand_info *info = to_davinci_nand(mtd); + + return davinci_nand_readl(info, NANDFSR_OFFSET) & BIT(0); +} + +/*----------------------------------------------------------------------*/ + +/* An ECC layout for using 4-bit ECC with small-page flash, storing + * ten ECC bytes plus the manufacturer's bad block marker byte, and + * and not overlapping the default BBT markers. + */ +static struct nand_ecclayout hwecc4_small = { + .eccbytes = 10, + .eccpos = { 0, 1, 2, 3, 4, + /* offset 5 holds the badblock marker */ + 6, 7, + 13, 14, 15, }, + .oobfree = { + {.offset = 8, .length = 5, }, + {.offset = 16, }, + }, +}; + +/* An ECC layout for using 4-bit ECC with large-page (2048bytes) flash, + * storing ten ECC bytes plus the manufacturer's bad block marker byte, + * and not overlapping the default BBT markers. + */ +static struct nand_ecclayout hwecc4_2048 = { + .eccbytes = 40, + .eccpos = { + /* at the end of spare sector */ + 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, + 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, + 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, + }, + .oobfree = { + /* 2 bytes at offset 0 hold manufacturer badblock markers */ + {.offset = 2, .length = 22, }, + /* 5 bytes at offset 8 hold BBT markers */ + /* 8 bytes at offset 16 hold JFFS2 clean markers */ + }, +}; + +#if defined(CONFIG_OF) +static const struct of_device_id davinci_nand_of_match[] = { + {.compatible = "ti,davinci-nand", }, + {.compatible = "ti,keystone-nand", }, + {}, +}; +MODULE_DEVICE_TABLE(of, davinci_nand_of_match); + +static struct davinci_nand_pdata + *nand_davinci_get_pdata(struct platform_device *pdev) +{ + if (!dev_get_platdata(&pdev->dev) && pdev->dev.of_node) { + struct davinci_nand_pdata *pdata; + const char *mode; + u32 prop; + + pdata = devm_kzalloc(&pdev->dev, + sizeof(struct davinci_nand_pdata), + GFP_KERNEL); + pdev->dev.platform_data = pdata; + if (!pdata) + return ERR_PTR(-ENOMEM); + if (!of_property_read_u32(pdev->dev.of_node, + "ti,davinci-chipselect", &prop)) + pdev->id = prop; + else + return ERR_PTR(-EINVAL); + + if (!of_property_read_u32(pdev->dev.of_node, + "ti,davinci-mask-ale", &prop)) + pdata->mask_ale = prop; + if (!of_property_read_u32(pdev->dev.of_node, + "ti,davinci-mask-cle", &prop)) + pdata->mask_cle = prop; + if (!of_property_read_u32(pdev->dev.of_node, + "ti,davinci-mask-chipsel", &prop)) + pdata->mask_chipsel = prop; + if (!of_property_read_string(pdev->dev.of_node, + "nand-ecc-mode", &mode) || + !of_property_read_string(pdev->dev.of_node, + "ti,davinci-ecc-mode", &mode)) { + if (!strncmp("none", mode, 4)) + pdata->ecc_mode = NAND_ECC_NONE; + if (!strncmp("soft", mode, 4)) + pdata->ecc_mode = NAND_ECC_SOFT; + if (!strncmp("hw", mode, 2)) + pdata->ecc_mode = NAND_ECC_HW; + } + if (!of_property_read_u32(pdev->dev.of_node, + "ti,davinci-ecc-bits", &prop)) + pdata->ecc_bits = prop; + + prop = of_get_nand_bus_width(pdev->dev.of_node); + if (0 < prop || !of_property_read_u32(pdev->dev.of_node, + "ti,davinci-nand-buswidth", &prop)) + if (prop == 16) + pdata->options |= NAND_BUSWIDTH_16; + if (of_property_read_bool(pdev->dev.of_node, + "nand-on-flash-bbt") || + of_property_read_bool(pdev->dev.of_node, + "ti,davinci-nand-use-bbt")) + pdata->bbt_options = NAND_BBT_USE_FLASH; + + if (of_device_is_compatible(pdev->dev.of_node, + "ti,keystone-nand")) { + pdata->options |= NAND_NO_SUBPAGE_WRITE; + } + } + + return dev_get_platdata(&pdev->dev); +} +#else +static struct davinci_nand_pdata + *nand_davinci_get_pdata(struct platform_device *pdev) +{ + return dev_get_platdata(&pdev->dev); +} +#endif + +static int nand_davinci_probe(struct platform_device *pdev) +{ + struct davinci_nand_pdata *pdata; + struct davinci_nand_info *info; + struct resource *res1; + struct resource *res2; + void __iomem *vaddr; + void __iomem *base; + int ret; + uint32_t val; + nand_ecc_modes_t ecc_mode; + + pdata = nand_davinci_get_pdata(pdev); + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + + /* insist on board-specific configuration */ + if (!pdata) + return -ENODEV; + + /* which external chipselect will we be managing? */ + if (pdev->id < 0 || pdev->id > 3) + return -ENODEV; + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + platform_set_drvdata(pdev, info); + + res1 = platform_get_resource(pdev, IORESOURCE_MEM, 0); + res2 = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!res1 || !res2) { + dev_err(&pdev->dev, "resource missing\n"); + return -EINVAL; + } + + vaddr = devm_ioremap_resource(&pdev->dev, res1); + if (IS_ERR(vaddr)) + return PTR_ERR(vaddr); + + /* + * This registers range is used to setup NAND settings. In case with + * TI AEMIF driver, the same memory address range is requested already + * by AEMIF, so we cannot request it twice, just ioremap. + * The AEMIF and NAND drivers not use the same registers in this range. + */ + base = devm_ioremap(&pdev->dev, res2->start, resource_size(res2)); + if (!base) { + dev_err(&pdev->dev, "ioremap failed for resource %pR\n", res2); + return -EADDRNOTAVAIL; + } + + info->dev = &pdev->dev; + info->base = base; + info->vaddr = vaddr; + + info->mtd.priv = &info->chip; + info->mtd.name = dev_name(&pdev->dev); + info->mtd.owner = THIS_MODULE; + + info->mtd.dev.parent = &pdev->dev; + + info->chip.IO_ADDR_R = vaddr; + info->chip.IO_ADDR_W = vaddr; + info->chip.chip_delay = 0; + info->chip.select_chip = nand_davinci_select_chip; + + /* options such as NAND_BBT_USE_FLASH */ + info->chip.bbt_options = pdata->bbt_options; + /* options such as 16-bit widths */ + info->chip.options = pdata->options; + info->chip.bbt_td = pdata->bbt_td; + info->chip.bbt_md = pdata->bbt_md; + info->timing = pdata->timing; + + info->ioaddr = (uint32_t __force) vaddr; + + info->current_cs = info->ioaddr; + info->core_chipsel = pdev->id; + info->mask_chipsel = pdata->mask_chipsel; + + /* use nandboot-capable ALE/CLE masks by default */ + info->mask_ale = pdata->mask_ale ? : MASK_ALE; + info->mask_cle = pdata->mask_cle ? : MASK_CLE; + + /* Set address of hardware control function */ + info->chip.cmd_ctrl = nand_davinci_hwcontrol; + info->chip.dev_ready = nand_davinci_dev_ready; + + /* Speed up buffer I/O */ + info->chip.read_buf = nand_davinci_read_buf; + info->chip.write_buf = nand_davinci_write_buf; + + /* Use board-specific ECC config */ + ecc_mode = pdata->ecc_mode; + + ret = -EINVAL; + switch (ecc_mode) { + case NAND_ECC_NONE: + case NAND_ECC_SOFT: + pdata->ecc_bits = 0; + break; + case NAND_ECC_HW: + if (pdata->ecc_bits == 4) { + /* No sanity checks: CPUs must support this, + * and the chips may not use NAND_BUSWIDTH_16. + */ + + /* No sharing 4-bit hardware between chipselects yet */ + spin_lock_irq(&davinci_nand_lock); + if (ecc4_busy) + ret = -EBUSY; + else + ecc4_busy = true; + spin_unlock_irq(&davinci_nand_lock); + + if (ret == -EBUSY) + return ret; + + info->chip.ecc.calculate = nand_davinci_calculate_4bit; + info->chip.ecc.correct = nand_davinci_correct_4bit; + info->chip.ecc.hwctl = nand_davinci_hwctl_4bit; + info->chip.ecc.bytes = 10; + } else { + info->chip.ecc.calculate = nand_davinci_calculate_1bit; + info->chip.ecc.correct = nand_davinci_correct_1bit; + info->chip.ecc.hwctl = nand_davinci_hwctl_1bit; + info->chip.ecc.bytes = 3; + } + info->chip.ecc.size = 512; + info->chip.ecc.strength = pdata->ecc_bits; + break; + default: + return -EINVAL; + } + info->chip.ecc.mode = ecc_mode; + + info->clk = devm_clk_get(&pdev->dev, "aemif"); + if (IS_ERR(info->clk)) { + ret = PTR_ERR(info->clk); + dev_dbg(&pdev->dev, "unable to get AEMIF clock, err %d\n", ret); + return ret; + } + + ret = clk_prepare_enable(info->clk); + if (ret < 0) { + dev_dbg(&pdev->dev, "unable to enable AEMIF clock, err %d\n", + ret); + goto err_clk_enable; + } + + spin_lock_irq(&davinci_nand_lock); + + /* put CSxNAND into NAND mode */ + val = davinci_nand_readl(info, NANDFCR_OFFSET); + val |= BIT(info->core_chipsel); + davinci_nand_writel(info, NANDFCR_OFFSET, val); + + spin_unlock_irq(&davinci_nand_lock); + + /* Scan to find existence of the device(s) */ + ret = nand_scan_ident(&info->mtd, pdata->mask_chipsel ? 2 : 1, NULL); + if (ret < 0) { + dev_dbg(&pdev->dev, "no NAND chip(s) found\n"); + goto err; + } + + /* Update ECC layout if needed ... for 1-bit HW ECC, the default + * is OK, but it allocates 6 bytes when only 3 are needed (for + * each 512 bytes). For the 4-bit HW ECC, that default is not + * usable: 10 bytes are needed, not 6. + */ + if (pdata->ecc_bits == 4) { + int chunks = info->mtd.writesize / 512; + + if (!chunks || info->mtd.oobsize < 16) { + dev_dbg(&pdev->dev, "too small\n"); + ret = -EINVAL; + goto err; + } + + /* For small page chips, preserve the manufacturer's + * badblock marking data ... and make sure a flash BBT + * table marker fits in the free bytes. + */ + if (chunks == 1) { + info->ecclayout = hwecc4_small; + info->ecclayout.oobfree[1].length = + info->mtd.oobsize - 16; + goto syndrome_done; + } + if (chunks == 4) { + info->ecclayout = hwecc4_2048; + info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST; + goto syndrome_done; + } + + /* 4KiB page chips are not yet supported. The eccpos from + * nand_ecclayout cannot hold 80 bytes and change to eccpos[] + * breaks userspace ioctl interface with mtd-utils. Once we + * resolve this issue, NAND_ECC_HW_OOB_FIRST mode can be used + * for the 4KiB page chips. + * + * TODO: Note that nand_ecclayout has now been expanded and can + * hold plenty of OOB entries. + */ + dev_warn(&pdev->dev, "no 4-bit ECC support yet " + "for 4KiB-page NAND\n"); + ret = -EIO; + goto err; + +syndrome_done: + info->chip.ecc.layout = &info->ecclayout; + } + + ret = nand_scan_tail(&info->mtd); + if (ret < 0) + goto err; + + if (pdata->parts) + ret = mtd_device_parse_register(&info->mtd, NULL, NULL, + pdata->parts, pdata->nr_parts); + else { + struct mtd_part_parser_data ppdata; + + ppdata.of_node = pdev->dev.of_node; + ret = mtd_device_parse_register(&info->mtd, NULL, &ppdata, + NULL, 0); + } + if (ret < 0) + goto err; + + val = davinci_nand_readl(info, NRCSR_OFFSET); + dev_info(&pdev->dev, "controller rev. %d.%d\n", + (val >> 8) & 0xff, val & 0xff); + + return 0; + +err: + clk_disable_unprepare(info->clk); + +err_clk_enable: + spin_lock_irq(&davinci_nand_lock); + if (ecc_mode == NAND_ECC_HW_SYNDROME) + ecc4_busy = false; + spin_unlock_irq(&davinci_nand_lock); + return ret; +} + +static int nand_davinci_remove(struct platform_device *pdev) +{ + struct davinci_nand_info *info = platform_get_drvdata(pdev); + + spin_lock_irq(&davinci_nand_lock); + if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME) + ecc4_busy = false; + spin_unlock_irq(&davinci_nand_lock); + + nand_release(&info->mtd); + + clk_disable_unprepare(info->clk); + + return 0; +} + +static struct platform_driver nand_davinci_driver = { + .probe = nand_davinci_probe, + .remove = nand_davinci_remove, + .driver = { + .name = "davinci_nand", + .of_match_table = of_match_ptr(davinci_nand_of_match), + }, +}; +MODULE_ALIAS("platform:davinci_nand"); + +module_platform_driver(nand_davinci_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Texas Instruments"); +MODULE_DESCRIPTION("Davinci NAND flash driver"); + diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c new file mode 100644 index 000000000..870c7fc0f --- /dev/null +++ b/drivers/mtd/nand/denali.c @@ -0,0 +1,1621 @@ +/* + * NAND Flash Controller Device Driver + * Copyright © 2009-2010, Intel Corporation and its suppliers. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * + */ +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/wait.h> +#include <linux/mutex.h> +#include <linux/slab.h> +#include <linux/mtd/mtd.h> +#include <linux/module.h> + +#include "denali.h" + +MODULE_LICENSE("GPL"); + +/* + * We define a module parameter that allows the user to override + * the hardware and decide what timing mode should be used. + */ +#define NAND_DEFAULT_TIMINGS -1 + +static int onfi_timing_mode = NAND_DEFAULT_TIMINGS; +module_param(onfi_timing_mode, int, S_IRUGO); +MODULE_PARM_DESC(onfi_timing_mode, + "Overrides default ONFI setting. -1 indicates use default timings"); + +#define DENALI_NAND_NAME "denali-nand" + +/* + * We define a macro here that combines all interrupts this driver uses into + * a single constant value, for convenience. + */ +#define DENALI_IRQ_ALL (INTR_STATUS__DMA_CMD_COMP | \ + INTR_STATUS__ECC_TRANSACTION_DONE | \ + INTR_STATUS__ECC_ERR | \ + INTR_STATUS__PROGRAM_FAIL | \ + INTR_STATUS__LOAD_COMP | \ + INTR_STATUS__PROGRAM_COMP | \ + INTR_STATUS__TIME_OUT | \ + INTR_STATUS__ERASE_FAIL | \ + INTR_STATUS__RST_COMP | \ + INTR_STATUS__ERASE_COMP) + +/* + * indicates whether or not the internal value for the flash bank is + * valid or not + */ +#define CHIP_SELECT_INVALID -1 + +#define SUPPORT_8BITECC 1 + +/* + * This macro divides two integers and rounds fractional values up + * to the nearest integer value. + */ +#define CEIL_DIV(X, Y) (((X)%(Y)) ? ((X)/(Y)+1) : ((X)/(Y))) + +/* + * this macro allows us to convert from an MTD structure to our own + * device context (denali) structure. + */ +#define mtd_to_denali(m) container_of(m, struct denali_nand_info, mtd) + +/* + * These constants are defined by the driver to enable common driver + * configuration options. + */ +#define SPARE_ACCESS 0x41 +#define MAIN_ACCESS 0x42 +#define MAIN_SPARE_ACCESS 0x43 +#define PIPELINE_ACCESS 0x2000 + +#define DENALI_READ 0 +#define DENALI_WRITE 0x100 + +/* types of device accesses. We can issue commands and get status */ +#define COMMAND_CYCLE 0 +#define ADDR_CYCLE 1 +#define STATUS_CYCLE 2 + +/* + * this is a helper macro that allows us to + * format the bank into the proper bits for the controller + */ +#define BANK(x) ((x) << 24) + +/* forward declarations */ +static void clear_interrupts(struct denali_nand_info *denali); +static uint32_t wait_for_irq(struct denali_nand_info *denali, + uint32_t irq_mask); +static void denali_irq_enable(struct denali_nand_info *denali, + uint32_t int_mask); +static uint32_t read_interrupt_status(struct denali_nand_info *denali); + +/* + * Certain operations for the denali NAND controller use an indexed mode to + * read/write data. The operation is performed by writing the address value + * of the command to the device memory followed by the data. This function + * abstracts this common operation. + */ +static void index_addr(struct denali_nand_info *denali, + uint32_t address, uint32_t data) +{ + iowrite32(address, denali->flash_mem); + iowrite32(data, denali->flash_mem + 0x10); +} + +/* Perform an indexed read of the device */ +static void index_addr_read_data(struct denali_nand_info *denali, + uint32_t address, uint32_t *pdata) +{ + iowrite32(address, denali->flash_mem); + *pdata = ioread32(denali->flash_mem + 0x10); +} + +/* + * We need to buffer some data for some of the NAND core routines. + * The operations manage buffering that data. + */ +static void reset_buf(struct denali_nand_info *denali) +{ + denali->buf.head = denali->buf.tail = 0; +} + +static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte) +{ + denali->buf.buf[denali->buf.tail++] = byte; +} + +/* reads the status of the device */ +static void read_status(struct denali_nand_info *denali) +{ + uint32_t cmd; + + /* initialize the data buffer to store status */ + reset_buf(denali); + + cmd = ioread32(denali->flash_reg + WRITE_PROTECT); + if (cmd) + write_byte_to_buf(denali, NAND_STATUS_WP); + else + write_byte_to_buf(denali, 0); +} + +/* resets a specific device connected to the core */ +static void reset_bank(struct denali_nand_info *denali) +{ + uint32_t irq_status; + uint32_t irq_mask = INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT; + + clear_interrupts(denali); + + iowrite32(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET); + + irq_status = wait_for_irq(denali, irq_mask); + + if (irq_status & INTR_STATUS__TIME_OUT) + dev_err(denali->dev, "reset bank failed.\n"); +} + +/* Reset the flash controller */ +static uint16_t denali_nand_reset(struct denali_nand_info *denali) +{ + int i; + + dev_dbg(denali->dev, "%s, Line %d, Function: %s\n", + __FILE__, __LINE__, __func__); + + for (i = 0; i < denali->max_banks; i++) + iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT, + denali->flash_reg + INTR_STATUS(i)); + + for (i = 0; i < denali->max_banks; i++) { + iowrite32(1 << i, denali->flash_reg + DEVICE_RESET); + while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) & + (INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT))) + cpu_relax(); + if (ioread32(denali->flash_reg + INTR_STATUS(i)) & + INTR_STATUS__TIME_OUT) + dev_dbg(denali->dev, + "NAND Reset operation timed out on bank %d\n", i); + } + + for (i = 0; i < denali->max_banks; i++) + iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT, + denali->flash_reg + INTR_STATUS(i)); + + return PASS; +} + +/* + * this routine calculates the ONFI timing values for a given mode and + * programs the clocking register accordingly. The mode is determined by + * the get_onfi_nand_para routine. + */ +static void nand_onfi_timing_set(struct denali_nand_info *denali, + uint16_t mode) +{ + uint16_t Trea[6] = {40, 30, 25, 20, 20, 16}; + uint16_t Trp[6] = {50, 25, 17, 15, 12, 10}; + uint16_t Treh[6] = {30, 15, 15, 10, 10, 7}; + uint16_t Trc[6] = {100, 50, 35, 30, 25, 20}; + uint16_t Trhoh[6] = {0, 15, 15, 15, 15, 15}; + uint16_t Trloh[6] = {0, 0, 0, 0, 5, 5}; + uint16_t Tcea[6] = {100, 45, 30, 25, 25, 25}; + uint16_t Tadl[6] = {200, 100, 100, 100, 70, 70}; + uint16_t Trhw[6] = {200, 100, 100, 100, 100, 100}; + uint16_t Trhz[6] = {200, 100, 100, 100, 100, 100}; + uint16_t Twhr[6] = {120, 80, 80, 60, 60, 60}; + uint16_t Tcs[6] = {70, 35, 25, 25, 20, 15}; + + uint16_t data_invalid_rhoh, data_invalid_rloh, data_invalid; + uint16_t dv_window = 0; + uint16_t en_lo, en_hi; + uint16_t acc_clks; + uint16_t addr_2_data, re_2_we, re_2_re, we_2_re, cs_cnt; + + dev_dbg(denali->dev, "%s, Line %d, Function: %s\n", + __FILE__, __LINE__, __func__); + + en_lo = CEIL_DIV(Trp[mode], CLK_X); + en_hi = CEIL_DIV(Treh[mode], CLK_X); +#if ONFI_BLOOM_TIME + if ((en_hi * CLK_X) < (Treh[mode] + 2)) + en_hi++; +#endif + + if ((en_lo + en_hi) * CLK_X < Trc[mode]) + en_lo += CEIL_DIV((Trc[mode] - (en_lo + en_hi) * CLK_X), CLK_X); + + if ((en_lo + en_hi) < CLK_MULTI) + en_lo += CLK_MULTI - en_lo - en_hi; + + while (dv_window < 8) { + data_invalid_rhoh = en_lo * CLK_X + Trhoh[mode]; + + data_invalid_rloh = (en_lo + en_hi) * CLK_X + Trloh[mode]; + + data_invalid = data_invalid_rhoh < data_invalid_rloh ? + data_invalid_rhoh : data_invalid_rloh; + + dv_window = data_invalid - Trea[mode]; + + if (dv_window < 8) + en_lo++; + } + + acc_clks = CEIL_DIV(Trea[mode], CLK_X); + + while (acc_clks * CLK_X - Trea[mode] < 3) + acc_clks++; + + if (data_invalid - acc_clks * CLK_X < 2) + dev_warn(denali->dev, "%s, Line %d: Warning!\n", + __FILE__, __LINE__); + + addr_2_data = CEIL_DIV(Tadl[mode], CLK_X); + re_2_we = CEIL_DIV(Trhw[mode], CLK_X); + re_2_re = CEIL_DIV(Trhz[mode], CLK_X); + we_2_re = CEIL_DIV(Twhr[mode], CLK_X); + cs_cnt = CEIL_DIV((Tcs[mode] - Trp[mode]), CLK_X); + if (cs_cnt == 0) + cs_cnt = 1; + + if (Tcea[mode]) { + while (cs_cnt * CLK_X + Trea[mode] < Tcea[mode]) + cs_cnt++; + } + +#if MODE5_WORKAROUND + if (mode == 5) + acc_clks = 5; +#endif + + /* Sighting 3462430: Temporary hack for MT29F128G08CJABAWP:B */ + if (ioread32(denali->flash_reg + MANUFACTURER_ID) == 0 && + ioread32(denali->flash_reg + DEVICE_ID) == 0x88) + acc_clks = 6; + + iowrite32(acc_clks, denali->flash_reg + ACC_CLKS); + iowrite32(re_2_we, denali->flash_reg + RE_2_WE); + iowrite32(re_2_re, denali->flash_reg + RE_2_RE); + iowrite32(we_2_re, denali->flash_reg + WE_2_RE); + iowrite32(addr_2_data, denali->flash_reg + ADDR_2_DATA); + iowrite32(en_lo, denali->flash_reg + RDWR_EN_LO_CNT); + iowrite32(en_hi, denali->flash_reg + RDWR_EN_HI_CNT); + iowrite32(cs_cnt, denali->flash_reg + CS_SETUP_CNT); +} + +/* queries the NAND device to see what ONFI modes it supports. */ +static uint16_t get_onfi_nand_para(struct denali_nand_info *denali) +{ + int i; + + /* + * we needn't to do a reset here because driver has already + * reset all the banks before + */ + if (!(ioread32(denali->flash_reg + ONFI_TIMING_MODE) & + ONFI_TIMING_MODE__VALUE)) + return FAIL; + + for (i = 5; i > 0; i--) { + if (ioread32(denali->flash_reg + ONFI_TIMING_MODE) & + (0x01 << i)) + break; + } + + nand_onfi_timing_set(denali, i); + + /* + * By now, all the ONFI devices we know support the page cache + * rw feature. So here we enable the pipeline_rw_ahead feature + */ + /* iowrite32(1, denali->flash_reg + CACHE_WRITE_ENABLE); */ + /* iowrite32(1, denali->flash_reg + CACHE_READ_ENABLE); */ + + return PASS; +} + +static void get_samsung_nand_para(struct denali_nand_info *denali, + uint8_t device_id) +{ + if (device_id == 0xd3) { /* Samsung K9WAG08U1A */ + /* Set timing register values according to datasheet */ + iowrite32(5, denali->flash_reg + ACC_CLKS); + iowrite32(20, denali->flash_reg + RE_2_WE); + iowrite32(12, denali->flash_reg + WE_2_RE); + iowrite32(14, denali->flash_reg + ADDR_2_DATA); + iowrite32(3, denali->flash_reg + RDWR_EN_LO_CNT); + iowrite32(2, denali->flash_reg + RDWR_EN_HI_CNT); + iowrite32(2, denali->flash_reg + CS_SETUP_CNT); + } +} + +static void get_toshiba_nand_para(struct denali_nand_info *denali) +{ + uint32_t tmp; + + /* + * Workaround to fix a controller bug which reports a wrong + * spare area size for some kind of Toshiba NAND device + */ + if ((ioread32(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) && + (ioread32(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64)) { + iowrite32(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE); + tmp = ioread32(denali->flash_reg + DEVICES_CONNECTED) * + ioread32(denali->flash_reg + DEVICE_SPARE_AREA_SIZE); + iowrite32(tmp, + denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE); +#if SUPPORT_15BITECC + iowrite32(15, denali->flash_reg + ECC_CORRECTION); +#elif SUPPORT_8BITECC + iowrite32(8, denali->flash_reg + ECC_CORRECTION); +#endif + } +} + +static void get_hynix_nand_para(struct denali_nand_info *denali, + uint8_t device_id) +{ + uint32_t main_size, spare_size; + + switch (device_id) { + case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */ + case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */ + iowrite32(128, denali->flash_reg + PAGES_PER_BLOCK); + iowrite32(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE); + iowrite32(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE); + main_size = 4096 * + ioread32(denali->flash_reg + DEVICES_CONNECTED); + spare_size = 224 * + ioread32(denali->flash_reg + DEVICES_CONNECTED); + iowrite32(main_size, + denali->flash_reg + LOGICAL_PAGE_DATA_SIZE); + iowrite32(spare_size, + denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE); + iowrite32(0, denali->flash_reg + DEVICE_WIDTH); +#if SUPPORT_15BITECC + iowrite32(15, denali->flash_reg + ECC_CORRECTION); +#elif SUPPORT_8BITECC + iowrite32(8, denali->flash_reg + ECC_CORRECTION); +#endif + break; + default: + dev_warn(denali->dev, + "Spectra: Unknown Hynix NAND (Device ID: 0x%x).\n" + "Will use default parameter values instead.\n", + device_id); + } +} + +/* + * determines how many NAND chips are connected to the controller. Note for + * Intel CE4100 devices we don't support more than one device. + */ +static void find_valid_banks(struct denali_nand_info *denali) +{ + uint32_t id[denali->max_banks]; + int i; + + denali->total_used_banks = 1; + for (i = 0; i < denali->max_banks; i++) { + index_addr(denali, MODE_11 | (i << 24) | 0, 0x90); + index_addr(denali, MODE_11 | (i << 24) | 1, 0); + index_addr_read_data(denali, MODE_11 | (i << 24) | 2, &id[i]); + + dev_dbg(denali->dev, + "Return 1st ID for bank[%d]: %x\n", i, id[i]); + + if (i == 0) { + if (!(id[i] & 0x0ff)) + break; /* WTF? */ + } else { + if ((id[i] & 0x0ff) == (id[0] & 0x0ff)) + denali->total_used_banks++; + else + break; + } + } + + if (denali->platform == INTEL_CE4100) { + /* + * Platform limitations of the CE4100 device limit + * users to a single chip solution for NAND. + * Multichip support is not enabled. + */ + if (denali->total_used_banks != 1) { + dev_err(denali->dev, + "Sorry, Intel CE4100 only supports a single NAND device.\n"); + BUG(); + } + } + dev_dbg(denali->dev, + "denali->total_used_banks: %d\n", denali->total_used_banks); +} + +/* + * Use the configuration feature register to determine the maximum number of + * banks that the hardware supports. + */ +static void detect_max_banks(struct denali_nand_info *denali) +{ + uint32_t features = ioread32(denali->flash_reg + FEATURES); + + denali->max_banks = 2 << (features & FEATURES__N_BANKS); +} + +static void detect_partition_feature(struct denali_nand_info *denali) +{ + /* + * For MRST platform, denali->fwblks represent the + * number of blocks firmware is taken, + * FW is in protect partition and MTD driver has no + * permission to access it. So let driver know how many + * blocks it can't touch. + */ + if (ioread32(denali->flash_reg + FEATURES) & FEATURES__PARTITION) { + if ((ioread32(denali->flash_reg + PERM_SRC_ID(1)) & + PERM_SRC_ID__SRCID) == SPECTRA_PARTITION_ID) { + denali->fwblks = + ((ioread32(denali->flash_reg + MIN_MAX_BANK(1)) & + MIN_MAX_BANK__MIN_VALUE) * + denali->blksperchip) + + + (ioread32(denali->flash_reg + MIN_BLK_ADDR(1)) & + MIN_BLK_ADDR__VALUE); + } else { + denali->fwblks = SPECTRA_START_BLOCK; + } + } else { + denali->fwblks = SPECTRA_START_BLOCK; + } +} + +static uint16_t denali_nand_timing_set(struct denali_nand_info *denali) +{ + uint16_t status = PASS; + uint32_t id_bytes[8], addr; + uint8_t maf_id, device_id; + int i; + + dev_dbg(denali->dev, "%s, Line %d, Function: %s\n", + __FILE__, __LINE__, __func__); + + /* + * Use read id method to get device ID and other params. + * For some NAND chips, controller can't report the correct + * device ID by reading from DEVICE_ID register + */ + addr = MODE_11 | BANK(denali->flash_bank); + index_addr(denali, addr | 0, 0x90); + index_addr(denali, addr | 1, 0); + for (i = 0; i < 8; i++) + index_addr_read_data(denali, addr | 2, &id_bytes[i]); + maf_id = id_bytes[0]; + device_id = id_bytes[1]; + + if (ioread32(denali->flash_reg + ONFI_DEVICE_NO_OF_LUNS) & + ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE) { /* ONFI 1.0 NAND */ + if (FAIL == get_onfi_nand_para(denali)) + return FAIL; + } else if (maf_id == 0xEC) { /* Samsung NAND */ + get_samsung_nand_para(denali, device_id); + } else if (maf_id == 0x98) { /* Toshiba NAND */ + get_toshiba_nand_para(denali); + } else if (maf_id == 0xAD) { /* Hynix NAND */ + get_hynix_nand_para(denali, device_id); + } + + dev_info(denali->dev, + "Dump timing register values:\n" + "acc_clks: %d, re_2_we: %d, re_2_re: %d\n" + "we_2_re: %d, addr_2_data: %d, rdwr_en_lo_cnt: %d\n" + "rdwr_en_hi_cnt: %d, cs_setup_cnt: %d\n", + ioread32(denali->flash_reg + ACC_CLKS), + ioread32(denali->flash_reg + RE_2_WE), + ioread32(denali->flash_reg + RE_2_RE), + ioread32(denali->flash_reg + WE_2_RE), + ioread32(denali->flash_reg + ADDR_2_DATA), + ioread32(denali->flash_reg + RDWR_EN_LO_CNT), + ioread32(denali->flash_reg + RDWR_EN_HI_CNT), + ioread32(denali->flash_reg + CS_SETUP_CNT)); + + find_valid_banks(denali); + + detect_partition_feature(denali); + + /* + * If the user specified to override the default timings + * with a specific ONFI mode, we apply those changes here. + */ + if (onfi_timing_mode != NAND_DEFAULT_TIMINGS) + nand_onfi_timing_set(denali, onfi_timing_mode); + + return status; +} + +static void denali_set_intr_modes(struct denali_nand_info *denali, + uint16_t INT_ENABLE) +{ + dev_dbg(denali->dev, "%s, Line %d, Function: %s\n", + __FILE__, __LINE__, __func__); + + if (INT_ENABLE) + iowrite32(1, denali->flash_reg + GLOBAL_INT_ENABLE); + else + iowrite32(0, denali->flash_reg + GLOBAL_INT_ENABLE); +} + +/* + * validation function to verify that the controlling software is making + * a valid request + */ +static inline bool is_flash_bank_valid(int flash_bank) +{ + return flash_bank >= 0 && flash_bank < 4; +} + +static void denali_irq_init(struct denali_nand_info *denali) +{ + uint32_t int_mask; + int i; + + /* Disable global interrupts */ + denali_set_intr_modes(denali, false); + + int_mask = DENALI_IRQ_ALL; + + /* Clear all status bits */ + for (i = 0; i < denali->max_banks; ++i) + iowrite32(0xFFFF, denali->flash_reg + INTR_STATUS(i)); + + denali_irq_enable(denali, int_mask); +} + +static void denali_irq_cleanup(int irqnum, struct denali_nand_info *denali) +{ + denali_set_intr_modes(denali, false); + free_irq(irqnum, denali); +} + +static void denali_irq_enable(struct denali_nand_info *denali, + uint32_t int_mask) +{ + int i; + + for (i = 0; i < denali->max_banks; ++i) + iowrite32(int_mask, denali->flash_reg + INTR_EN(i)); +} + +/* + * This function only returns when an interrupt that this driver cares about + * occurs. This is to reduce the overhead of servicing interrupts + */ +static inline uint32_t denali_irq_detected(struct denali_nand_info *denali) +{ + return read_interrupt_status(denali) & DENALI_IRQ_ALL; +} + +/* Interrupts are cleared by writing a 1 to the appropriate status bit */ +static inline void clear_interrupt(struct denali_nand_info *denali, + uint32_t irq_mask) +{ + uint32_t intr_status_reg; + + intr_status_reg = INTR_STATUS(denali->flash_bank); + + iowrite32(irq_mask, denali->flash_reg + intr_status_reg); +} + +static void clear_interrupts(struct denali_nand_info *denali) +{ + uint32_t status; + + spin_lock_irq(&denali->irq_lock); + + status = read_interrupt_status(denali); + clear_interrupt(denali, status); + + denali->irq_status = 0x0; + spin_unlock_irq(&denali->irq_lock); +} + +static uint32_t read_interrupt_status(struct denali_nand_info *denali) +{ + uint32_t intr_status_reg; + + intr_status_reg = INTR_STATUS(denali->flash_bank); + + return ioread32(denali->flash_reg + intr_status_reg); +} + +/* + * This is the interrupt service routine. It handles all interrupts + * sent to this device. Note that on CE4100, this is a shared interrupt. + */ +static irqreturn_t denali_isr(int irq, void *dev_id) +{ + struct denali_nand_info *denali = dev_id; + uint32_t irq_status; + irqreturn_t result = IRQ_NONE; + + spin_lock(&denali->irq_lock); + + /* check to see if a valid NAND chip has been selected. */ + if (is_flash_bank_valid(denali->flash_bank)) { + /* + * check to see if controller generated the interrupt, + * since this is a shared interrupt + */ + irq_status = denali_irq_detected(denali); + if (irq_status != 0) { + /* handle interrupt */ + /* first acknowledge it */ + clear_interrupt(denali, irq_status); + /* + * store the status in the device context for someone + * to read + */ + denali->irq_status |= irq_status; + /* notify anyone who cares that it happened */ + complete(&denali->complete); + /* tell the OS that we've handled this */ + result = IRQ_HANDLED; + } + } + spin_unlock(&denali->irq_lock); + return result; +} +#define BANK(x) ((x) << 24) + +static uint32_t wait_for_irq(struct denali_nand_info *denali, uint32_t irq_mask) +{ + unsigned long comp_res; + uint32_t intr_status; + unsigned long timeout = msecs_to_jiffies(1000); + + do { + comp_res = + wait_for_completion_timeout(&denali->complete, timeout); + spin_lock_irq(&denali->irq_lock); + intr_status = denali->irq_status; + + if (intr_status & irq_mask) { + denali->irq_status &= ~irq_mask; + spin_unlock_irq(&denali->irq_lock); + /* our interrupt was detected */ + break; + } + + /* + * these are not the interrupts you are looking for - + * need to wait again + */ + spin_unlock_irq(&denali->irq_lock); + } while (comp_res != 0); + + if (comp_res == 0) { + /* timeout */ + pr_err("timeout occurred, status = 0x%x, mask = 0x%x\n", + intr_status, irq_mask); + + intr_status = 0; + } + return intr_status; +} + +/* + * This helper function setups the registers for ECC and whether or not + * the spare area will be transferred. + */ +static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en, + bool transfer_spare) +{ + int ecc_en_flag, transfer_spare_flag; + + /* set ECC, transfer spare bits if needed */ + ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0; + transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0; + + /* Enable spare area/ECC per user's request. */ + iowrite32(ecc_en_flag, denali->flash_reg + ECC_ENABLE); + iowrite32(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG); +} + +/* + * sends a pipeline command operation to the controller. See the Denali NAND + * controller's user guide for more information (section 4.2.3.6). + */ +static int denali_send_pipeline_cmd(struct denali_nand_info *denali, + bool ecc_en, bool transfer_spare, + int access_type, int op) +{ + int status = PASS; + uint32_t page_count = 1; + uint32_t addr, cmd, irq_status, irq_mask; + + if (op == DENALI_READ) + irq_mask = INTR_STATUS__LOAD_COMP; + else if (op == DENALI_WRITE) + irq_mask = 0; + else + BUG(); + + setup_ecc_for_xfer(denali, ecc_en, transfer_spare); + + clear_interrupts(denali); + + addr = BANK(denali->flash_bank) | denali->page; + + if (op == DENALI_WRITE && access_type != SPARE_ACCESS) { + cmd = MODE_01 | addr; + iowrite32(cmd, denali->flash_mem); + } else if (op == DENALI_WRITE && access_type == SPARE_ACCESS) { + /* read spare area */ + cmd = MODE_10 | addr; + index_addr(denali, cmd, access_type); + + cmd = MODE_01 | addr; + iowrite32(cmd, denali->flash_mem); + } else if (op == DENALI_READ) { + /* setup page read request for access type */ + cmd = MODE_10 | addr; + index_addr(denali, cmd, access_type); + + /* + * page 33 of the NAND controller spec indicates we should not + * use the pipeline commands in Spare area only mode. + * So we don't. + */ + if (access_type == SPARE_ACCESS) { + cmd = MODE_01 | addr; + iowrite32(cmd, denali->flash_mem); + } else { + index_addr(denali, cmd, + PIPELINE_ACCESS | op | page_count); + + /* + * wait for command to be accepted + * can always use status0 bit as the + * mask is identical for each bank. + */ + irq_status = wait_for_irq(denali, irq_mask); + + if (irq_status == 0) { + dev_err(denali->dev, + "cmd, page, addr on timeout (0x%x, 0x%x, 0x%x)\n", + cmd, denali->page, addr); + status = FAIL; + } else { + cmd = MODE_01 | addr; + iowrite32(cmd, denali->flash_mem); + } + } + } + return status; +} + +/* helper function that simply writes a buffer to the flash */ +static int write_data_to_flash_mem(struct denali_nand_info *denali, + const uint8_t *buf, int len) +{ + uint32_t *buf32; + int i; + + /* + * verify that the len is a multiple of 4. + * see comment in read_data_from_flash_mem() + */ + BUG_ON((len % 4) != 0); + + /* write the data to the flash memory */ + buf32 = (uint32_t *)buf; + for (i = 0; i < len / 4; i++) + iowrite32(*buf32++, denali->flash_mem + 0x10); + return i * 4; /* intent is to return the number of bytes read */ +} + +/* helper function that simply reads a buffer from the flash */ +static int read_data_from_flash_mem(struct denali_nand_info *denali, + uint8_t *buf, int len) +{ + uint32_t *buf32; + int i; + + /* + * we assume that len will be a multiple of 4, if not it would be nice + * to know about it ASAP rather than have random failures... + * This assumption is based on the fact that this function is designed + * to be used to read flash pages, which are typically multiples of 4. + */ + BUG_ON((len % 4) != 0); + + /* transfer the data from the flash */ + buf32 = (uint32_t *)buf; + for (i = 0; i < len / 4; i++) + *buf32++ = ioread32(denali->flash_mem + 0x10); + return i * 4; /* intent is to return the number of bytes read */ +} + +/* writes OOB data to the device */ +static int write_oob_data(struct mtd_info *mtd, uint8_t *buf, int page) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + uint32_t irq_status; + uint32_t irq_mask = INTR_STATUS__PROGRAM_COMP | + INTR_STATUS__PROGRAM_FAIL; + int status = 0; + + denali->page = page; + + if (denali_send_pipeline_cmd(denali, false, false, SPARE_ACCESS, + DENALI_WRITE) == PASS) { + write_data_to_flash_mem(denali, buf, mtd->oobsize); + + /* wait for operation to complete */ + irq_status = wait_for_irq(denali, irq_mask); + + if (irq_status == 0) { + dev_err(denali->dev, "OOB write failed\n"); + status = -EIO; + } + } else { + dev_err(denali->dev, "unable to send pipeline command\n"); + status = -EIO; + } + return status; +} + +/* reads OOB data from the device */ +static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + uint32_t irq_mask = INTR_STATUS__LOAD_COMP; + uint32_t irq_status, addr, cmd; + + denali->page = page; + + if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS, + DENALI_READ) == PASS) { + read_data_from_flash_mem(denali, buf, mtd->oobsize); + + /* + * wait for command to be accepted + * can always use status0 bit as the + * mask is identical for each bank. + */ + irq_status = wait_for_irq(denali, irq_mask); + + if (irq_status == 0) + dev_err(denali->dev, "page on OOB timeout %d\n", + denali->page); + + /* + * We set the device back to MAIN_ACCESS here as I observed + * instability with the controller if you do a block erase + * and the last transaction was a SPARE_ACCESS. Block erase + * is reliable (according to the MTD test infrastructure) + * if you are in MAIN_ACCESS. + */ + addr = BANK(denali->flash_bank) | denali->page; + cmd = MODE_10 | addr; + index_addr(denali, cmd, MAIN_ACCESS); + } +} + +/* + * this function examines buffers to see if they contain data that + * indicate that the buffer is part of an erased region of flash. + */ +static bool is_erased(uint8_t *buf, int len) +{ + int i; + + for (i = 0; i < len; i++) + if (buf[i] != 0xFF) + return false; + return true; +} +#define ECC_SECTOR_SIZE 512 + +#define ECC_SECTOR(x) (((x) & ECC_ERROR_ADDRESS__SECTOR_NR) >> 12) +#define ECC_BYTE(x) (((x) & ECC_ERROR_ADDRESS__OFFSET)) +#define ECC_CORRECTION_VALUE(x) ((x) & ERR_CORRECTION_INFO__BYTEMASK) +#define ECC_ERROR_CORRECTABLE(x) (!((x) & ERR_CORRECTION_INFO__ERROR_TYPE)) +#define ECC_ERR_DEVICE(x) (((x) & ERR_CORRECTION_INFO__DEVICE_NR) >> 8) +#define ECC_LAST_ERR(x) ((x) & ERR_CORRECTION_INFO__LAST_ERR_INFO) + +static bool handle_ecc(struct denali_nand_info *denali, uint8_t *buf, + uint32_t irq_status, unsigned int *max_bitflips) +{ + bool check_erased_page = false; + unsigned int bitflips = 0; + + if (irq_status & INTR_STATUS__ECC_ERR) { + /* read the ECC errors. we'll ignore them for now */ + uint32_t err_address, err_correction_info, err_byte, + err_sector, err_device, err_correction_value; + denali_set_intr_modes(denali, false); + + do { + err_address = ioread32(denali->flash_reg + + ECC_ERROR_ADDRESS); + err_sector = ECC_SECTOR(err_address); + err_byte = ECC_BYTE(err_address); + + err_correction_info = ioread32(denali->flash_reg + + ERR_CORRECTION_INFO); + err_correction_value = + ECC_CORRECTION_VALUE(err_correction_info); + err_device = ECC_ERR_DEVICE(err_correction_info); + + if (ECC_ERROR_CORRECTABLE(err_correction_info)) { + /* + * If err_byte is larger than ECC_SECTOR_SIZE, + * means error happened in OOB, so we ignore + * it. It's no need for us to correct it + * err_device is represented the NAND error + * bits are happened in if there are more + * than one NAND connected. + */ + if (err_byte < ECC_SECTOR_SIZE) { + int offset; + + offset = (err_sector * + ECC_SECTOR_SIZE + + err_byte) * + denali->devnum + + err_device; + /* correct the ECC error */ + buf[offset] ^= err_correction_value; + denali->mtd.ecc_stats.corrected++; + bitflips++; + } + } else { + /* + * if the error is not correctable, need to + * look at the page to see if it is an erased + * page. if so, then it's not a real ECC error + */ + check_erased_page = true; + } + } while (!ECC_LAST_ERR(err_correction_info)); + /* + * Once handle all ecc errors, controller will triger + * a ECC_TRANSACTION_DONE interrupt, so here just wait + * for a while for this interrupt + */ + while (!(read_interrupt_status(denali) & + INTR_STATUS__ECC_TRANSACTION_DONE)) + cpu_relax(); + clear_interrupts(denali); + denali_set_intr_modes(denali, true); + } + *max_bitflips = bitflips; + return check_erased_page; +} + +/* programs the controller to either enable/disable DMA transfers */ +static void denali_enable_dma(struct denali_nand_info *denali, bool en) +{ + iowrite32(en ? DMA_ENABLE__FLAG : 0, denali->flash_reg + DMA_ENABLE); + ioread32(denali->flash_reg + DMA_ENABLE); +} + +/* setups the HW to perform the data DMA */ +static void denali_setup_dma(struct denali_nand_info *denali, int op) +{ + uint32_t mode; + const int page_count = 1; + uint32_t addr = denali->buf.dma_buf; + + mode = MODE_10 | BANK(denali->flash_bank); + + /* DMA is a four step process */ + + /* 1. setup transfer type and # of pages */ + index_addr(denali, mode | denali->page, 0x2000 | op | page_count); + + /* 2. set memory high address bits 23:8 */ + index_addr(denali, mode | ((addr >> 16) << 8), 0x2200); + + /* 3. set memory low address bits 23:8 */ + index_addr(denali, mode | ((addr & 0xffff) << 8), 0x2300); + + /* 4. interrupt when complete, burst len = 64 bytes */ + index_addr(denali, mode | 0x14000, 0x2400); +} + +/* + * writes a page. user specifies type, and this function handles the + * configuration details. + */ +static int write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, bool raw_xfer) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + dma_addr_t addr = denali->buf.dma_buf; + size_t size = denali->mtd.writesize + denali->mtd.oobsize; + uint32_t irq_status; + uint32_t irq_mask = INTR_STATUS__DMA_CMD_COMP | + INTR_STATUS__PROGRAM_FAIL; + + /* + * if it is a raw xfer, we want to disable ecc and send the spare area. + * !raw_xfer - enable ecc + * raw_xfer - transfer spare + */ + setup_ecc_for_xfer(denali, !raw_xfer, raw_xfer); + + /* copy buffer into DMA buffer */ + memcpy(denali->buf.buf, buf, mtd->writesize); + + if (raw_xfer) { + /* transfer the data to the spare area */ + memcpy(denali->buf.buf + mtd->writesize, + chip->oob_poi, + mtd->oobsize); + } + + dma_sync_single_for_device(denali->dev, addr, size, DMA_TO_DEVICE); + + clear_interrupts(denali); + denali_enable_dma(denali, true); + + denali_setup_dma(denali, DENALI_WRITE); + + /* wait for operation to complete */ + irq_status = wait_for_irq(denali, irq_mask); + + if (irq_status == 0) { + dev_err(denali->dev, "timeout on write_page (type = %d)\n", + raw_xfer); + denali->status = NAND_STATUS_FAIL; + } + + denali_enable_dma(denali, false); + dma_sync_single_for_cpu(denali->dev, addr, size, DMA_TO_DEVICE); + + return 0; +} + +/* NAND core entry points */ + +/* + * this is the callback that the NAND core calls to write a page. Since + * writing a page with ECC or without is similar, all the work is done + * by write_page above. + */ +static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + /* + * for regular page writes, we let HW handle all the ECC + * data written to the device. + */ + return write_page(mtd, chip, buf, false); +} + +/* + * This is the callback that the NAND core calls to write a page without ECC. + * raw access is similar to ECC page writes, so all the work is done in the + * write_page() function above. + */ +static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + /* + * for raw page writes, we want to disable ECC and simply write + * whatever data is in the buffer. + */ + return write_page(mtd, chip, buf, true); +} + +static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + return write_oob_data(mtd, chip->oob_poi, page); +} + +static int denali_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + read_oob_data(mtd, chip->oob_poi, page); + + return 0; +} + +static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + unsigned int max_bitflips; + struct denali_nand_info *denali = mtd_to_denali(mtd); + + dma_addr_t addr = denali->buf.dma_buf; + size_t size = denali->mtd.writesize + denali->mtd.oobsize; + + uint32_t irq_status; + uint32_t irq_mask = INTR_STATUS__ECC_TRANSACTION_DONE | + INTR_STATUS__ECC_ERR; + bool check_erased_page = false; + + if (page != denali->page) { + dev_err(denali->dev, + "IN %s: page %d is not equal to denali->page %d", + __func__, page, denali->page); + BUG(); + } + + setup_ecc_for_xfer(denali, true, false); + + denali_enable_dma(denali, true); + dma_sync_single_for_device(denali->dev, addr, size, DMA_FROM_DEVICE); + + clear_interrupts(denali); + denali_setup_dma(denali, DENALI_READ); + + /* wait for operation to complete */ + irq_status = wait_for_irq(denali, irq_mask); + + dma_sync_single_for_cpu(denali->dev, addr, size, DMA_FROM_DEVICE); + + memcpy(buf, denali->buf.buf, mtd->writesize); + + check_erased_page = handle_ecc(denali, buf, irq_status, &max_bitflips); + denali_enable_dma(denali, false); + + if (check_erased_page) { + read_oob_data(&denali->mtd, chip->oob_poi, denali->page); + + /* check ECC failures that may have occurred on erased pages */ + if (check_erased_page) { + if (!is_erased(buf, denali->mtd.writesize)) + denali->mtd.ecc_stats.failed++; + if (!is_erased(buf, denali->mtd.oobsize)) + denali->mtd.ecc_stats.failed++; + } + } + return max_bitflips; +} + +static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + dma_addr_t addr = denali->buf.dma_buf; + size_t size = denali->mtd.writesize + denali->mtd.oobsize; + uint32_t irq_mask = INTR_STATUS__DMA_CMD_COMP; + + if (page != denali->page) { + dev_err(denali->dev, + "IN %s: page %d is not equal to denali->page %d", + __func__, page, denali->page); + BUG(); + } + + setup_ecc_for_xfer(denali, false, true); + denali_enable_dma(denali, true); + + dma_sync_single_for_device(denali->dev, addr, size, DMA_FROM_DEVICE); + + clear_interrupts(denali); + denali_setup_dma(denali, DENALI_READ); + + /* wait for operation to complete */ + wait_for_irq(denali, irq_mask); + + dma_sync_single_for_cpu(denali->dev, addr, size, DMA_FROM_DEVICE); + + denali_enable_dma(denali, false); + + memcpy(buf, denali->buf.buf, mtd->writesize); + memcpy(chip->oob_poi, denali->buf.buf + mtd->writesize, mtd->oobsize); + + return 0; +} + +static uint8_t denali_read_byte(struct mtd_info *mtd) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + uint8_t result = 0xff; + + if (denali->buf.head < denali->buf.tail) + result = denali->buf.buf[denali->buf.head++]; + + return result; +} + +static void denali_select_chip(struct mtd_info *mtd, int chip) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + + spin_lock_irq(&denali->irq_lock); + denali->flash_bank = chip; + spin_unlock_irq(&denali->irq_lock); +} + +static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + int status = denali->status; + + denali->status = 0; + + return status; +} + +static int denali_erase(struct mtd_info *mtd, int page) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + + uint32_t cmd, irq_status; + + clear_interrupts(denali); + + /* setup page read request for access type */ + cmd = MODE_10 | BANK(denali->flash_bank) | page; + index_addr(denali, cmd, 0x1); + + /* wait for erase to complete or failure to occur */ + irq_status = wait_for_irq(denali, INTR_STATUS__ERASE_COMP | + INTR_STATUS__ERASE_FAIL); + + return irq_status & INTR_STATUS__ERASE_FAIL ? NAND_STATUS_FAIL : PASS; +} + +static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col, + int page) +{ + struct denali_nand_info *denali = mtd_to_denali(mtd); + uint32_t addr, id; + int i; + + switch (cmd) { + case NAND_CMD_PAGEPROG: + break; + case NAND_CMD_STATUS: + read_status(denali); + break; + case NAND_CMD_READID: + case NAND_CMD_PARAM: + reset_buf(denali); + /* + * sometimes ManufactureId read from register is not right + * e.g. some of Micron MT29F32G08QAA MLC NAND chips + * So here we send READID cmd to NAND insteand + */ + addr = MODE_11 | BANK(denali->flash_bank); + index_addr(denali, addr | 0, 0x90); + index_addr(denali, addr | 1, 0); + for (i = 0; i < 8; i++) { + index_addr_read_data(denali, addr | 2, &id); + write_byte_to_buf(denali, id); + } + break; + case NAND_CMD_READ0: + case NAND_CMD_SEQIN: + denali->page = page; + break; + case NAND_CMD_RESET: + reset_bank(denali); + break; + case NAND_CMD_READOOB: + /* TODO: Read OOB data */ + break; + default: + pr_err(": unsupported command received 0x%x\n", cmd); + break; + } +} +/* end NAND core entry points */ + +/* Initialization code to bring the device up to a known good state */ +static void denali_hw_init(struct denali_nand_info *denali) +{ + /* + * tell driver how many bit controller will skip before + * writing ECC code in OOB, this register may be already + * set by firmware. So we read this value out. + * if this value is 0, just let it be. + */ + denali->bbtskipbytes = ioread32(denali->flash_reg + + SPARE_AREA_SKIP_BYTES); + detect_max_banks(denali); + denali_nand_reset(denali); + iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED); + iowrite32(CHIP_EN_DONT_CARE__FLAG, + denali->flash_reg + CHIP_ENABLE_DONT_CARE); + + iowrite32(0xffff, denali->flash_reg + SPARE_AREA_MARKER); + + /* Should set value for these registers when init */ + iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES); + iowrite32(1, denali->flash_reg + ECC_ENABLE); + denali_nand_timing_set(denali); + denali_irq_init(denali); +} + +/* + * Althogh controller spec said SLC ECC is forceb to be 4bit, + * but denali controller in MRST only support 15bit and 8bit ECC + * correction + */ +#define ECC_8BITS 14 +static struct nand_ecclayout nand_8bit_oob = { + .eccbytes = 14, +}; + +#define ECC_15BITS 26 +static struct nand_ecclayout nand_15bit_oob = { + .eccbytes = 26, +}; + +static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' }; +static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 8, + .len = 4, + .veroffs = 12, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 8, + .len = 4, + .veroffs = 12, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/* initialize driver data structures */ +static void denali_drv_init(struct denali_nand_info *denali) +{ + denali->idx = 0; + + /* setup interrupt handler */ + /* + * the completion object will be used to notify + * the callee that the interrupt is done + */ + init_completion(&denali->complete); + + /* + * the spinlock will be used to synchronize the ISR with any + * element that might be access shared data (interrupt status) + */ + spin_lock_init(&denali->irq_lock); + + /* indicate that MTD has not selected a valid bank yet */ + denali->flash_bank = CHIP_SELECT_INVALID; + + /* initialize our irq_status variable to indicate no interrupts */ + denali->irq_status = 0; +} + +int denali_init(struct denali_nand_info *denali) +{ + int ret; + + if (denali->platform == INTEL_CE4100) { + /* + * Due to a silicon limitation, we can only support + * ONFI timing mode 1 and below. + */ + if (onfi_timing_mode < -1 || onfi_timing_mode > 1) { + pr_err("Intel CE4100 only supports ONFI timing mode 1 or below\n"); + return -EINVAL; + } + } + + /* allocate a temporary buffer for nand_scan_ident() */ + denali->buf.buf = devm_kzalloc(denali->dev, PAGE_SIZE, + GFP_DMA | GFP_KERNEL); + if (!denali->buf.buf) + return -ENOMEM; + + denali->mtd.dev.parent = denali->dev; + denali_hw_init(denali); + denali_drv_init(denali); + + /* + * denali_isr register is done after all the hardware + * initilization is finished + */ + if (request_irq(denali->irq, denali_isr, IRQF_SHARED, + DENALI_NAND_NAME, denali)) { + pr_err("Spectra: Unable to allocate IRQ\n"); + return -ENODEV; + } + + /* now that our ISR is registered, we can enable interrupts */ + denali_set_intr_modes(denali, true); + denali->mtd.name = "denali-nand"; + denali->mtd.owner = THIS_MODULE; + denali->mtd.priv = &denali->nand; + + /* register the driver with the NAND core subsystem */ + denali->nand.select_chip = denali_select_chip; + denali->nand.cmdfunc = denali_cmdfunc; + denali->nand.read_byte = denali_read_byte; + denali->nand.waitfunc = denali_waitfunc; + + /* + * scan for NAND devices attached to the controller + * this is the first stage in a two step process to register + * with the nand subsystem + */ + if (nand_scan_ident(&denali->mtd, denali->max_banks, NULL)) { + ret = -ENXIO; + goto failed_req_irq; + } + + /* allocate the right size buffer now */ + devm_kfree(denali->dev, denali->buf.buf); + denali->buf.buf = devm_kzalloc(denali->dev, + denali->mtd.writesize + denali->mtd.oobsize, + GFP_KERNEL); + if (!denali->buf.buf) { + ret = -ENOMEM; + goto failed_req_irq; + } + + /* Is 32-bit DMA supported? */ + ret = dma_set_mask(denali->dev, DMA_BIT_MASK(32)); + if (ret) { + pr_err("Spectra: no usable DMA configuration\n"); + goto failed_req_irq; + } + + denali->buf.dma_buf = dma_map_single(denali->dev, denali->buf.buf, + denali->mtd.writesize + denali->mtd.oobsize, + DMA_BIDIRECTIONAL); + if (dma_mapping_error(denali->dev, denali->buf.dma_buf)) { + dev_err(denali->dev, "Spectra: failed to map DMA buffer\n"); + ret = -EIO; + goto failed_req_irq; + } + + /* + * support for multi nand + * MTD known nothing about multi nand, so we should tell it + * the real pagesize and anything necessery + */ + denali->devnum = ioread32(denali->flash_reg + DEVICES_CONNECTED); + denali->nand.chipsize <<= (denali->devnum - 1); + denali->nand.page_shift += (denali->devnum - 1); + denali->nand.pagemask = (denali->nand.chipsize >> + denali->nand.page_shift) - 1; + denali->nand.bbt_erase_shift += (denali->devnum - 1); + denali->nand.phys_erase_shift = denali->nand.bbt_erase_shift; + denali->nand.chip_shift += (denali->devnum - 1); + denali->mtd.writesize <<= (denali->devnum - 1); + denali->mtd.oobsize <<= (denali->devnum - 1); + denali->mtd.erasesize <<= (denali->devnum - 1); + denali->mtd.size = denali->nand.numchips * denali->nand.chipsize; + denali->bbtskipbytes *= denali->devnum; + + /* + * second stage of the NAND scan + * this stage requires information regarding ECC and + * bad block management. + */ + + /* Bad block management */ + denali->nand.bbt_td = &bbt_main_descr; + denali->nand.bbt_md = &bbt_mirror_descr; + + /* skip the scan for now until we have OOB read and write support */ + denali->nand.bbt_options |= NAND_BBT_USE_FLASH; + denali->nand.options |= NAND_SKIP_BBTSCAN; + denali->nand.ecc.mode = NAND_ECC_HW_SYNDROME; + + /* no subpage writes on denali */ + denali->nand.options |= NAND_NO_SUBPAGE_WRITE; + + /* + * Denali Controller only support 15bit and 8bit ECC in MRST, + * so just let controller do 15bit ECC for MLC and 8bit ECC for + * SLC if possible. + * */ + if (!nand_is_slc(&denali->nand) && + (denali->mtd.oobsize > (denali->bbtskipbytes + + ECC_15BITS * (denali->mtd.writesize / + ECC_SECTOR_SIZE)))) { + /* if MLC OOB size is large enough, use 15bit ECC*/ + denali->nand.ecc.strength = 15; + denali->nand.ecc.layout = &nand_15bit_oob; + denali->nand.ecc.bytes = ECC_15BITS; + iowrite32(15, denali->flash_reg + ECC_CORRECTION); + } else if (denali->mtd.oobsize < (denali->bbtskipbytes + + ECC_8BITS * (denali->mtd.writesize / + ECC_SECTOR_SIZE))) { + pr_err("Your NAND chip OOB is not large enough to contain 8bit ECC correction codes"); + goto failed_req_irq; + } else { + denali->nand.ecc.strength = 8; + denali->nand.ecc.layout = &nand_8bit_oob; + denali->nand.ecc.bytes = ECC_8BITS; + iowrite32(8, denali->flash_reg + ECC_CORRECTION); + } + + denali->nand.ecc.bytes *= denali->devnum; + denali->nand.ecc.strength *= denali->devnum; + denali->nand.ecc.layout->eccbytes *= + denali->mtd.writesize / ECC_SECTOR_SIZE; + denali->nand.ecc.layout->oobfree[0].offset = + denali->bbtskipbytes + denali->nand.ecc.layout->eccbytes; + denali->nand.ecc.layout->oobfree[0].length = + denali->mtd.oobsize - denali->nand.ecc.layout->eccbytes - + denali->bbtskipbytes; + + /* + * Let driver know the total blocks number and how many blocks + * contained by each nand chip. blksperchip will help driver to + * know how many blocks is taken by FW. + */ + denali->totalblks = denali->mtd.size >> denali->nand.phys_erase_shift; + denali->blksperchip = denali->totalblks / denali->nand.numchips; + + /* override the default read operations */ + denali->nand.ecc.size = ECC_SECTOR_SIZE * denali->devnum; + denali->nand.ecc.read_page = denali_read_page; + denali->nand.ecc.read_page_raw = denali_read_page_raw; + denali->nand.ecc.write_page = denali_write_page; + denali->nand.ecc.write_page_raw = denali_write_page_raw; + denali->nand.ecc.read_oob = denali_read_oob; + denali->nand.ecc.write_oob = denali_write_oob; + denali->nand.erase = denali_erase; + + if (nand_scan_tail(&denali->mtd)) { + ret = -ENXIO; + goto failed_req_irq; + } + + ret = mtd_device_register(&denali->mtd, NULL, 0); + if (ret) { + dev_err(denali->dev, "Spectra: Failed to register MTD: %d\n", + ret); + goto failed_req_irq; + } + return 0; + +failed_req_irq: + denali_irq_cleanup(denali->irq, denali); + + return ret; +} +EXPORT_SYMBOL(denali_init); + +/* driver exit point */ +void denali_remove(struct denali_nand_info *denali) +{ + denali_irq_cleanup(denali->irq, denali); + dma_unmap_single(denali->dev, denali->buf.dma_buf, + denali->mtd.writesize + denali->mtd.oobsize, + DMA_BIDIRECTIONAL); +} +EXPORT_SYMBOL(denali_remove); diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h new file mode 100644 index 000000000..145bf8893 --- /dev/null +++ b/drivers/mtd/nand/denali.h @@ -0,0 +1,483 @@ +/* + * NAND Flash Controller Device Driver + * Copyright (c) 2009 - 2010, Intel Corporation and its suppliers. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * + */ + +#ifndef __DENALI_H__ +#define __DENALI_H__ + +#include <linux/mtd/nand.h> + +#define DEVICE_RESET 0x0 +#define DEVICE_RESET__BANK0 0x0001 +#define DEVICE_RESET__BANK1 0x0002 +#define DEVICE_RESET__BANK2 0x0004 +#define DEVICE_RESET__BANK3 0x0008 + +#define TRANSFER_SPARE_REG 0x10 +#define TRANSFER_SPARE_REG__FLAG 0x0001 + +#define LOAD_WAIT_CNT 0x20 +#define LOAD_WAIT_CNT__VALUE 0xffff + +#define PROGRAM_WAIT_CNT 0x30 +#define PROGRAM_WAIT_CNT__VALUE 0xffff + +#define ERASE_WAIT_CNT 0x40 +#define ERASE_WAIT_CNT__VALUE 0xffff + +#define INT_MON_CYCCNT 0x50 +#define INT_MON_CYCCNT__VALUE 0xffff + +#define RB_PIN_ENABLED 0x60 +#define RB_PIN_ENABLED__BANK0 0x0001 +#define RB_PIN_ENABLED__BANK1 0x0002 +#define RB_PIN_ENABLED__BANK2 0x0004 +#define RB_PIN_ENABLED__BANK3 0x0008 + +#define MULTIPLANE_OPERATION 0x70 +#define MULTIPLANE_OPERATION__FLAG 0x0001 + +#define MULTIPLANE_READ_ENABLE 0x80 +#define MULTIPLANE_READ_ENABLE__FLAG 0x0001 + +#define COPYBACK_DISABLE 0x90 +#define COPYBACK_DISABLE__FLAG 0x0001 + +#define CACHE_WRITE_ENABLE 0xa0 +#define CACHE_WRITE_ENABLE__FLAG 0x0001 + +#define CACHE_READ_ENABLE 0xb0 +#define CACHE_READ_ENABLE__FLAG 0x0001 + +#define PREFETCH_MODE 0xc0 +#define PREFETCH_MODE__PREFETCH_EN 0x0001 +#define PREFETCH_MODE__PREFETCH_BURST_LENGTH 0xfff0 + +#define CHIP_ENABLE_DONT_CARE 0xd0 +#define CHIP_EN_DONT_CARE__FLAG 0x01 + +#define ECC_ENABLE 0xe0 +#define ECC_ENABLE__FLAG 0x0001 + +#define GLOBAL_INT_ENABLE 0xf0 +#define GLOBAL_INT_EN_FLAG 0x01 + +#define WE_2_RE 0x100 +#define WE_2_RE__VALUE 0x003f + +#define ADDR_2_DATA 0x110 +#define ADDR_2_DATA__VALUE 0x003f + +#define RE_2_WE 0x120 +#define RE_2_WE__VALUE 0x003f + +#define ACC_CLKS 0x130 +#define ACC_CLKS__VALUE 0x000f + +#define NUMBER_OF_PLANES 0x140 +#define NUMBER_OF_PLANES__VALUE 0x0007 + +#define PAGES_PER_BLOCK 0x150 +#define PAGES_PER_BLOCK__VALUE 0xffff + +#define DEVICE_WIDTH 0x160 +#define DEVICE_WIDTH__VALUE 0x0003 + +#define DEVICE_MAIN_AREA_SIZE 0x170 +#define DEVICE_MAIN_AREA_SIZE__VALUE 0xffff + +#define DEVICE_SPARE_AREA_SIZE 0x180 +#define DEVICE_SPARE_AREA_SIZE__VALUE 0xffff + +#define TWO_ROW_ADDR_CYCLES 0x190 +#define TWO_ROW_ADDR_CYCLES__FLAG 0x0001 + +#define MULTIPLANE_ADDR_RESTRICT 0x1a0 +#define MULTIPLANE_ADDR_RESTRICT__FLAG 0x0001 + +#define ECC_CORRECTION 0x1b0 +#define ECC_CORRECTION__VALUE 0x001f + +#define READ_MODE 0x1c0 +#define READ_MODE__VALUE 0x000f + +#define WRITE_MODE 0x1d0 +#define WRITE_MODE__VALUE 0x000f + +#define COPYBACK_MODE 0x1e0 +#define COPYBACK_MODE__VALUE 0x000f + +#define RDWR_EN_LO_CNT 0x1f0 +#define RDWR_EN_LO_CNT__VALUE 0x001f + +#define RDWR_EN_HI_CNT 0x200 +#define RDWR_EN_HI_CNT__VALUE 0x001f + +#define MAX_RD_DELAY 0x210 +#define MAX_RD_DELAY__VALUE 0x000f + +#define CS_SETUP_CNT 0x220 +#define CS_SETUP_CNT__VALUE 0x001f + +#define SPARE_AREA_SKIP_BYTES 0x230 +#define SPARE_AREA_SKIP_BYTES__VALUE 0x003f + +#define SPARE_AREA_MARKER 0x240 +#define SPARE_AREA_MARKER__VALUE 0xffff + +#define DEVICES_CONNECTED 0x250 +#define DEVICES_CONNECTED__VALUE 0x0007 + +#define DIE_MASK 0x260 +#define DIE_MASK__VALUE 0x00ff + +#define FIRST_BLOCK_OF_NEXT_PLANE 0x270 +#define FIRST_BLOCK_OF_NEXT_PLANE__VALUE 0xffff + +#define WRITE_PROTECT 0x280 +#define WRITE_PROTECT__FLAG 0x0001 + +#define RE_2_RE 0x290 +#define RE_2_RE__VALUE 0x003f + +#define MANUFACTURER_ID 0x300 +#define MANUFACTURER_ID__VALUE 0x00ff + +#define DEVICE_ID 0x310 +#define DEVICE_ID__VALUE 0x00ff + +#define DEVICE_PARAM_0 0x320 +#define DEVICE_PARAM_0__VALUE 0x00ff + +#define DEVICE_PARAM_1 0x330 +#define DEVICE_PARAM_1__VALUE 0x00ff + +#define DEVICE_PARAM_2 0x340 +#define DEVICE_PARAM_2__VALUE 0x00ff + +#define LOGICAL_PAGE_DATA_SIZE 0x350 +#define LOGICAL_PAGE_DATA_SIZE__VALUE 0xffff + +#define LOGICAL_PAGE_SPARE_SIZE 0x360 +#define LOGICAL_PAGE_SPARE_SIZE__VALUE 0xffff + +#define REVISION 0x370 +#define REVISION__VALUE 0xffff + +#define ONFI_DEVICE_FEATURES 0x380 +#define ONFI_DEVICE_FEATURES__VALUE 0x003f + +#define ONFI_OPTIONAL_COMMANDS 0x390 +#define ONFI_OPTIONAL_COMMANDS__VALUE 0x003f + +#define ONFI_TIMING_MODE 0x3a0 +#define ONFI_TIMING_MODE__VALUE 0x003f + +#define ONFI_PGM_CACHE_TIMING_MODE 0x3b0 +#define ONFI_PGM_CACHE_TIMING_MODE__VALUE 0x003f + +#define ONFI_DEVICE_NO_OF_LUNS 0x3c0 +#define ONFI_DEVICE_NO_OF_LUNS__NO_OF_LUNS 0x00ff +#define ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE 0x0100 + +#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L 0x3d0 +#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L__VALUE 0xffff + +#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U 0x3e0 +#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U__VALUE 0xffff + +#define FEATURES 0x3f0 +#define FEATURES__N_BANKS 0x0003 +#define FEATURES__ECC_MAX_ERR 0x003c +#define FEATURES__DMA 0x0040 +#define FEATURES__CMD_DMA 0x0080 +#define FEATURES__PARTITION 0x0100 +#define FEATURES__XDMA_SIDEBAND 0x0200 +#define FEATURES__GPREG 0x0400 +#define FEATURES__INDEX_ADDR 0x0800 + +#define TRANSFER_MODE 0x400 +#define TRANSFER_MODE__VALUE 0x0003 + +#define INTR_STATUS(__bank) (0x410 + ((__bank) * 0x50)) +#define INTR_EN(__bank) (0x420 + ((__bank) * 0x50)) + +#define INTR_STATUS__ECC_TRANSACTION_DONE 0x0001 +#define INTR_STATUS__ECC_ERR 0x0002 +#define INTR_STATUS__DMA_CMD_COMP 0x0004 +#define INTR_STATUS__TIME_OUT 0x0008 +#define INTR_STATUS__PROGRAM_FAIL 0x0010 +#define INTR_STATUS__ERASE_FAIL 0x0020 +#define INTR_STATUS__LOAD_COMP 0x0040 +#define INTR_STATUS__PROGRAM_COMP 0x0080 +#define INTR_STATUS__ERASE_COMP 0x0100 +#define INTR_STATUS__PIPE_CPYBCK_CMD_COMP 0x0200 +#define INTR_STATUS__LOCKED_BLK 0x0400 +#define INTR_STATUS__UNSUP_CMD 0x0800 +#define INTR_STATUS__INT_ACT 0x1000 +#define INTR_STATUS__RST_COMP 0x2000 +#define INTR_STATUS__PIPE_CMD_ERR 0x4000 +#define INTR_STATUS__PAGE_XFER_INC 0x8000 + +#define INTR_EN__ECC_TRANSACTION_DONE 0x0001 +#define INTR_EN__ECC_ERR 0x0002 +#define INTR_EN__DMA_CMD_COMP 0x0004 +#define INTR_EN__TIME_OUT 0x0008 +#define INTR_EN__PROGRAM_FAIL 0x0010 +#define INTR_EN__ERASE_FAIL 0x0020 +#define INTR_EN__LOAD_COMP 0x0040 +#define INTR_EN__PROGRAM_COMP 0x0080 +#define INTR_EN__ERASE_COMP 0x0100 +#define INTR_EN__PIPE_CPYBCK_CMD_COMP 0x0200 +#define INTR_EN__LOCKED_BLK 0x0400 +#define INTR_EN__UNSUP_CMD 0x0800 +#define INTR_EN__INT_ACT 0x1000 +#define INTR_EN__RST_COMP 0x2000 +#define INTR_EN__PIPE_CMD_ERR 0x4000 +#define INTR_EN__PAGE_XFER_INC 0x8000 + +#define PAGE_CNT(__bank) (0x430 + ((__bank) * 0x50)) +#define ERR_PAGE_ADDR(__bank) (0x440 + ((__bank) * 0x50)) +#define ERR_BLOCK_ADDR(__bank) (0x450 + ((__bank) * 0x50)) + +#define DATA_INTR 0x550 +#define DATA_INTR__WRITE_SPACE_AV 0x0001 +#define DATA_INTR__READ_DATA_AV 0x0002 + +#define DATA_INTR_EN 0x560 +#define DATA_INTR_EN__WRITE_SPACE_AV 0x0001 +#define DATA_INTR_EN__READ_DATA_AV 0x0002 + +#define GPREG_0 0x570 +#define GPREG_0__VALUE 0xffff + +#define GPREG_1 0x580 +#define GPREG_1__VALUE 0xffff + +#define GPREG_2 0x590 +#define GPREG_2__VALUE 0xffff + +#define GPREG_3 0x5a0 +#define GPREG_3__VALUE 0xffff + +#define ECC_THRESHOLD 0x600 +#define ECC_THRESHOLD__VALUE 0x03ff + +#define ECC_ERROR_BLOCK_ADDRESS 0x610 +#define ECC_ERROR_BLOCK_ADDRESS__VALUE 0xffff + +#define ECC_ERROR_PAGE_ADDRESS 0x620 +#define ECC_ERROR_PAGE_ADDRESS__VALUE 0x0fff +#define ECC_ERROR_PAGE_ADDRESS__BANK 0xf000 + +#define ECC_ERROR_ADDRESS 0x630 +#define ECC_ERROR_ADDRESS__OFFSET 0x0fff +#define ECC_ERROR_ADDRESS__SECTOR_NR 0xf000 + +#define ERR_CORRECTION_INFO 0x640 +#define ERR_CORRECTION_INFO__BYTEMASK 0x00ff +#define ERR_CORRECTION_INFO__DEVICE_NR 0x0f00 +#define ERR_CORRECTION_INFO__ERROR_TYPE 0x4000 +#define ERR_CORRECTION_INFO__LAST_ERR_INFO 0x8000 + +#define DMA_ENABLE 0x700 +#define DMA_ENABLE__FLAG 0x0001 + +#define IGNORE_ECC_DONE 0x710 +#define IGNORE_ECC_DONE__FLAG 0x0001 + +#define DMA_INTR 0x720 +#define DMA_INTR__TARGET_ERROR 0x0001 +#define DMA_INTR__DESC_COMP_CHANNEL0 0x0002 +#define DMA_INTR__DESC_COMP_CHANNEL1 0x0004 +#define DMA_INTR__DESC_COMP_CHANNEL2 0x0008 +#define DMA_INTR__DESC_COMP_CHANNEL3 0x0010 +#define DMA_INTR__MEMCOPY_DESC_COMP 0x0020 + +#define DMA_INTR_EN 0x730 +#define DMA_INTR_EN__TARGET_ERROR 0x0001 +#define DMA_INTR_EN__DESC_COMP_CHANNEL0 0x0002 +#define DMA_INTR_EN__DESC_COMP_CHANNEL1 0x0004 +#define DMA_INTR_EN__DESC_COMP_CHANNEL2 0x0008 +#define DMA_INTR_EN__DESC_COMP_CHANNEL3 0x0010 +#define DMA_INTR_EN__MEMCOPY_DESC_COMP 0x0020 + +#define TARGET_ERR_ADDR_LO 0x740 +#define TARGET_ERR_ADDR_LO__VALUE 0xffff + +#define TARGET_ERR_ADDR_HI 0x750 +#define TARGET_ERR_ADDR_HI__VALUE 0xffff + +#define CHNL_ACTIVE 0x760 +#define CHNL_ACTIVE__CHANNEL0 0x0001 +#define CHNL_ACTIVE__CHANNEL1 0x0002 +#define CHNL_ACTIVE__CHANNEL2 0x0004 +#define CHNL_ACTIVE__CHANNEL3 0x0008 + +#define ACTIVE_SRC_ID 0x800 +#define ACTIVE_SRC_ID__VALUE 0x00ff + +#define PTN_INTR 0x810 +#define PTN_INTR__CONFIG_ERROR 0x0001 +#define PTN_INTR__ACCESS_ERROR_BANK0 0x0002 +#define PTN_INTR__ACCESS_ERROR_BANK1 0x0004 +#define PTN_INTR__ACCESS_ERROR_BANK2 0x0008 +#define PTN_INTR__ACCESS_ERROR_BANK3 0x0010 +#define PTN_INTR__REG_ACCESS_ERROR 0x0020 + +#define PTN_INTR_EN 0x820 +#define PTN_INTR_EN__CONFIG_ERROR 0x0001 +#define PTN_INTR_EN__ACCESS_ERROR_BANK0 0x0002 +#define PTN_INTR_EN__ACCESS_ERROR_BANK1 0x0004 +#define PTN_INTR_EN__ACCESS_ERROR_BANK2 0x0008 +#define PTN_INTR_EN__ACCESS_ERROR_BANK3 0x0010 +#define PTN_INTR_EN__REG_ACCESS_ERROR 0x0020 + +#define PERM_SRC_ID(__bank) (0x830 + ((__bank) * 0x40)) +#define PERM_SRC_ID__SRCID 0x00ff +#define PERM_SRC_ID__DIRECT_ACCESS_ACTIVE 0x0800 +#define PERM_SRC_ID__WRITE_ACTIVE 0x2000 +#define PERM_SRC_ID__READ_ACTIVE 0x4000 +#define PERM_SRC_ID__PARTITION_VALID 0x8000 + +#define MIN_BLK_ADDR(__bank) (0x840 + ((__bank) * 0x40)) +#define MIN_BLK_ADDR__VALUE 0xffff + +#define MAX_BLK_ADDR(__bank) (0x850 + ((__bank) * 0x40)) +#define MAX_BLK_ADDR__VALUE 0xffff + +#define MIN_MAX_BANK(__bank) (0x860 + ((__bank) * 0x40)) +#define MIN_MAX_BANK__MIN_VALUE 0x0003 +#define MIN_MAX_BANK__MAX_VALUE 0x000c + + +/* ffsdefs.h */ +#define CLEAR 0 /*use this to clear a field instead of "fail"*/ +#define SET 1 /*use this to set a field instead of "pass"*/ +#define FAIL 1 /*failed flag*/ +#define PASS 0 /*success flag*/ +#define ERR -1 /*error flag*/ + +/* lld.h */ +#define GOOD_BLOCK 0 +#define DEFECTIVE_BLOCK 1 +#define READ_ERROR 2 + +#define CLK_X 5 +#define CLK_MULTI 4 + +/* spectraswconfig.h */ +#define CMD_DMA 0 + +#define SPECTRA_PARTITION_ID 0 +/**** Block Table and Reserved Block Parameters *****/ +#define SPECTRA_START_BLOCK 3 +#define NUM_FREE_BLOCKS_GATE 30 + +/* KBV - Updated to LNW scratch register address */ +#define SCRATCH_REG_ADDR CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR +#define SCRATCH_REG_SIZE 64 + +#define GLOB_HWCTL_DEFAULT_BLKS 2048 + +#define SUPPORT_15BITECC 1 +#define SUPPORT_8BITECC 1 + +#define CUSTOM_CONF_PARAMS 0 + +#define ONFI_BLOOM_TIME 1 +#define MODE5_WORKAROUND 0 + + +#define MODE_00 0x00000000 +#define MODE_01 0x04000000 +#define MODE_10 0x08000000 +#define MODE_11 0x0C000000 + + +#define DATA_TRANSFER_MODE 0 +#define PROTECTION_PER_BLOCK 1 +#define LOAD_WAIT_COUNT 2 +#define PROGRAM_WAIT_COUNT 3 +#define ERASE_WAIT_COUNT 4 +#define INT_MONITOR_CYCLE_COUNT 5 +#define READ_BUSY_PIN_ENABLED 6 +#define MULTIPLANE_OPERATION_SUPPORT 7 +#define PRE_FETCH_MODE 8 +#define CE_DONT_CARE_SUPPORT 9 +#define COPYBACK_SUPPORT 10 +#define CACHE_WRITE_SUPPORT 11 +#define CACHE_READ_SUPPORT 12 +#define NUM_PAGES_IN_BLOCK 13 +#define ECC_ENABLE_SELECT 14 +#define WRITE_ENABLE_2_READ_ENABLE 15 +#define ADDRESS_2_DATA 16 +#define READ_ENABLE_2_WRITE_ENABLE 17 +#define TWO_ROW_ADDRESS_CYCLES 18 +#define MULTIPLANE_ADDRESS_RESTRICT 19 +#define ACC_CLOCKS 20 +#define READ_WRITE_ENABLE_LOW_COUNT 21 +#define READ_WRITE_ENABLE_HIGH_COUNT 22 + +#define ECC_SECTOR_SIZE 512 + +struct nand_buf { + int head; + int tail; + uint8_t *buf; + dma_addr_t dma_buf; +}; + +#define INTEL_CE4100 1 +#define INTEL_MRST 2 +#define DT 3 + +struct denali_nand_info { + struct mtd_info mtd; + struct nand_chip nand; + int flash_bank; /* currently selected chip */ + int status; + int platform; + struct nand_buf buf; + struct device *dev; + int total_used_banks; + uint32_t block; /* stored for future use */ + uint16_t page; + void __iomem *flash_reg; /* Mapped io reg base address */ + void __iomem *flash_mem; /* Mapped io reg base address */ + + /* elements used by ISR */ + struct completion complete; + spinlock_t irq_lock; + uint32_t irq_status; + int irq_debug_array[32]; + int idx; + int irq; + + uint32_t devnum; /* represent how many nands connected */ + uint32_t fwblks; /* represent how many blocks FW used */ + uint32_t totalblks; + uint32_t blksperchip; + uint32_t bbtskipbytes; + uint32_t max_banks; +}; + +extern int denali_init(struct denali_nand_info *denali); +extern void denali_remove(struct denali_nand_info *denali); + +#endif /* __DENALI_H__ */ diff --git a/drivers/mtd/nand/denali_dt.c b/drivers/mtd/nand/denali_dt.c new file mode 100644 index 000000000..0cb1e8d9f --- /dev/null +++ b/drivers/mtd/nand/denali_dt.c @@ -0,0 +1,131 @@ +/* + * NAND Flash Controller Device Driver for DT + * + * Copyright © 2011, Picochip. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/slab.h> + +#include "denali.h" + +struct denali_dt { + struct denali_nand_info denali; + struct clk *clk; +}; + +static const struct of_device_id denali_nand_dt_ids[] = { + { .compatible = "denali,denali-nand-dt" }, + { /* sentinel */ } + }; + +MODULE_DEVICE_TABLE(of, denali_nand_dt_ids); + +static u64 denali_dma_mask; + +static int denali_dt_probe(struct platform_device *ofdev) +{ + struct resource *denali_reg, *nand_data; + struct denali_dt *dt; + struct denali_nand_info *denali; + int ret; + const struct of_device_id *of_id; + + of_id = of_match_device(denali_nand_dt_ids, &ofdev->dev); + if (of_id) { + ofdev->id_entry = of_id->data; + } else { + pr_err("Failed to find the right device id.\n"); + return -ENOMEM; + } + + dt = devm_kzalloc(&ofdev->dev, sizeof(*dt), GFP_KERNEL); + if (!dt) + return -ENOMEM; + denali = &dt->denali; + + denali->platform = DT; + denali->dev = &ofdev->dev; + denali->irq = platform_get_irq(ofdev, 0); + if (denali->irq < 0) { + dev_err(&ofdev->dev, "no irq defined\n"); + return denali->irq; + } + + denali_reg = platform_get_resource_byname(ofdev, IORESOURCE_MEM, "denali_reg"); + denali->flash_reg = devm_ioremap_resource(&ofdev->dev, denali_reg); + if (IS_ERR(denali->flash_reg)) + return PTR_ERR(denali->flash_reg); + + nand_data = platform_get_resource_byname(ofdev, IORESOURCE_MEM, "nand_data"); + denali->flash_mem = devm_ioremap_resource(&ofdev->dev, nand_data); + if (IS_ERR(denali->flash_mem)) + return PTR_ERR(denali->flash_mem); + + if (!of_property_read_u32(ofdev->dev.of_node, + "dma-mask", (u32 *)&denali_dma_mask)) { + denali->dev->dma_mask = &denali_dma_mask; + } else { + denali->dev->dma_mask = NULL; + } + + dt->clk = devm_clk_get(&ofdev->dev, NULL); + if (IS_ERR(dt->clk)) { + dev_err(&ofdev->dev, "no clk available\n"); + return PTR_ERR(dt->clk); + } + clk_prepare_enable(dt->clk); + + ret = denali_init(denali); + if (ret) + goto out_disable_clk; + + platform_set_drvdata(ofdev, dt); + return 0; + +out_disable_clk: + clk_disable_unprepare(dt->clk); + + return ret; +} + +static int denali_dt_remove(struct platform_device *ofdev) +{ + struct denali_dt *dt = platform_get_drvdata(ofdev); + + denali_remove(&dt->denali); + clk_disable(dt->clk); + + return 0; +} + +static struct platform_driver denali_dt_driver = { + .probe = denali_dt_probe, + .remove = denali_dt_remove, + .driver = { + .name = "denali-nand-dt", + .of_match_table = denali_nand_dt_ids, + }, +}; + +module_platform_driver(denali_dt_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Jamie Iles"); +MODULE_DESCRIPTION("DT driver for Denali NAND controller"); diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/denali_pci.c new file mode 100644 index 000000000..6e2f387b8 --- /dev/null +++ b/drivers/mtd/nand/denali_pci.c @@ -0,0 +1,142 @@ +/* + * NAND Flash Controller Device Driver + * Copyright © 2009-2010, Intel Corporation and its suppliers. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/slab.h> + +#include "denali.h" + +#define DENALI_NAND_NAME "denali-nand-pci" + +/* List of platforms this NAND controller has be integrated into */ +static const struct pci_device_id denali_pci_ids[] = { + { PCI_VDEVICE(INTEL, 0x0701), INTEL_CE4100 }, + { PCI_VDEVICE(INTEL, 0x0809), INTEL_MRST }, + { /* end: all zeroes */ } +}; +MODULE_DEVICE_TABLE(pci, denali_pci_ids); + +static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id) +{ + int ret = -ENODEV; + resource_size_t csr_base, mem_base; + unsigned long csr_len, mem_len; + struct denali_nand_info *denali; + + denali = kzalloc(sizeof(*denali), GFP_KERNEL); + if (!denali) + return -ENOMEM; + + ret = pci_enable_device(dev); + if (ret) { + pr_err("Spectra: pci_enable_device failed.\n"); + goto failed_alloc_memery; + } + + if (id->driver_data == INTEL_CE4100) { + denali->platform = INTEL_CE4100; + mem_base = pci_resource_start(dev, 0); + mem_len = pci_resource_len(dev, 1); + csr_base = pci_resource_start(dev, 1); + csr_len = pci_resource_len(dev, 1); + } else { + denali->platform = INTEL_MRST; + csr_base = pci_resource_start(dev, 0); + csr_len = pci_resource_len(dev, 0); + mem_base = pci_resource_start(dev, 1); + mem_len = pci_resource_len(dev, 1); + if (!mem_len) { + mem_base = csr_base + csr_len; + mem_len = csr_len; + } + } + + pci_set_master(dev); + denali->dev = &dev->dev; + denali->irq = dev->irq; + + ret = pci_request_regions(dev, DENALI_NAND_NAME); + if (ret) { + pr_err("Spectra: Unable to request memory regions\n"); + goto failed_enable_dev; + } + + denali->flash_reg = ioremap_nocache(csr_base, csr_len); + if (!denali->flash_reg) { + pr_err("Spectra: Unable to remap memory region\n"); + ret = -ENOMEM; + goto failed_req_regions; + } + + denali->flash_mem = ioremap_nocache(mem_base, mem_len); + if (!denali->flash_mem) { + pr_err("Spectra: ioremap_nocache failed!"); + ret = -ENOMEM; + goto failed_remap_reg; + } + + ret = denali_init(denali); + if (ret) + goto failed_remap_mem; + + pci_set_drvdata(dev, denali); + + return 0; + +failed_remap_mem: + iounmap(denali->flash_mem); +failed_remap_reg: + iounmap(denali->flash_reg); +failed_req_regions: + pci_release_regions(dev); +failed_enable_dev: + pci_disable_device(dev); +failed_alloc_memery: + kfree(denali); + + return ret; +} + +/* driver exit point */ +static void denali_pci_remove(struct pci_dev *dev) +{ + struct denali_nand_info *denali = pci_get_drvdata(dev); + + denali_remove(denali); + iounmap(denali->flash_reg); + iounmap(denali->flash_mem); + pci_release_regions(dev); + pci_disable_device(dev); + kfree(denali); +} + +static struct pci_driver denali_pci_driver = { + .name = DENALI_NAND_NAME, + .id_table = denali_pci_ids, + .probe = denali_pci_probe, + .remove = denali_pci_remove, +}; + +static int denali_init_pci(void) +{ + return pci_register_driver(&denali_pci_driver); +} +module_init(denali_init_pci); + +static void denali_exit_pci(void) +{ + pci_unregister_driver(&denali_pci_driver); +} +module_exit(denali_exit_pci); diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c new file mode 100644 index 000000000..f68a7bcce --- /dev/null +++ b/drivers/mtd/nand/diskonchip.c @@ -0,0 +1,1716 @@ +/* + * drivers/mtd/nand/diskonchip.c + * + * (C) 2003 Red Hat, Inc. + * (C) 2004 Dan Brown <dan_brown@ieee.org> + * (C) 2004 Kalev Lember <kalev@smartlink.ee> + * + * Author: David Woodhouse <dwmw2@infradead.org> + * Additional Diskonchip 2000 and Millennium support by Dan Brown <dan_brown@ieee.org> + * Diskonchip Millennium Plus support by Kalev Lember <kalev@smartlink.ee> + * + * Error correction code lifted from the old docecc code + * Author: Fabrice Bellard (fabrice.bellard@netgem.com) + * Copyright (C) 2000 Netgem S.A. + * converted to the generic Reed-Solomon library by Thomas Gleixner <tglx@linutronix.de> + * + * Interface to generic NAND code for M-Systems DiskOnChip devices + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/sched.h> +#include <linux/delay.h> +#include <linux/rslib.h> +#include <linux/moduleparam.h> +#include <linux/slab.h> +#include <asm/io.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/doc2000.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/inftl.h> +#include <linux/module.h> + +/* Where to look for the devices? */ +#ifndef CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS +#define CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS 0 +#endif + +static unsigned long doc_locations[] __initdata = { +#if defined (__alpha__) || defined(__i386__) || defined(__x86_64__) +#ifdef CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH + 0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000, + 0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000, + 0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000, + 0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000, + 0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000, +#else + 0xc8000, 0xca000, 0xcc000, 0xce000, + 0xd0000, 0xd2000, 0xd4000, 0xd6000, + 0xd8000, 0xda000, 0xdc000, 0xde000, + 0xe0000, 0xe2000, 0xe4000, 0xe6000, + 0xe8000, 0xea000, 0xec000, 0xee000, +#endif +#endif + 0xffffffff }; + +static struct mtd_info *doclist = NULL; + +struct doc_priv { + void __iomem *virtadr; + unsigned long physadr; + u_char ChipID; + u_char CDSNControl; + int chips_per_floor; /* The number of chips detected on each floor */ + int curfloor; + int curchip; + int mh0_page; + int mh1_page; + struct mtd_info *nextdoc; +}; + +/* This is the syndrome computed by the HW ecc generator upon reading an empty + page, one with all 0xff for data and stored ecc code. */ +static u_char empty_read_syndrome[6] = { 0x26, 0xff, 0x6d, 0x47, 0x73, 0x7a }; + +/* This is the ecc value computed by the HW ecc generator upon writing an empty + page, one with all 0xff for data. */ +static u_char empty_write_ecc[6] = { 0x4b, 0x00, 0xe2, 0x0e, 0x93, 0xf7 }; + +#define INFTL_BBT_RESERVED_BLOCKS 4 + +#define DoC_is_MillenniumPlus(doc) ((doc)->ChipID == DOC_ChipID_DocMilPlus16 || (doc)->ChipID == DOC_ChipID_DocMilPlus32) +#define DoC_is_Millennium(doc) ((doc)->ChipID == DOC_ChipID_DocMil) +#define DoC_is_2000(doc) ((doc)->ChipID == DOC_ChipID_Doc2k) + +static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int bitmask); +static void doc200x_select_chip(struct mtd_info *mtd, int chip); + +static int debug = 0; +module_param(debug, int, 0); + +static int try_dword = 1; +module_param(try_dword, int, 0); + +static int no_ecc_failures = 0; +module_param(no_ecc_failures, int, 0); + +static int no_autopart = 0; +module_param(no_autopart, int, 0); + +static int show_firmware_partition = 0; +module_param(show_firmware_partition, int, 0); + +#ifdef CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE +static int inftl_bbt_write = 1; +#else +static int inftl_bbt_write = 0; +#endif +module_param(inftl_bbt_write, int, 0); + +static unsigned long doc_config_location = CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS; +module_param(doc_config_location, ulong, 0); +MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip"); + +/* Sector size for HW ECC */ +#define SECTOR_SIZE 512 +/* The sector bytes are packed into NB_DATA 10 bit words */ +#define NB_DATA (((SECTOR_SIZE + 1) * 8 + 6) / 10) +/* Number of roots */ +#define NROOTS 4 +/* First consective root */ +#define FCR 510 +/* Number of symbols */ +#define NN 1023 + +/* the Reed Solomon control structure */ +static struct rs_control *rs_decoder; + +/* + * The HW decoder in the DoC ASIC's provides us a error syndrome, + * which we must convert to a standard syndrome usable by the generic + * Reed-Solomon library code. + * + * Fabrice Bellard figured this out in the old docecc code. I added + * some comments, improved a minor bit and converted it to make use + * of the generic Reed-Solomon library. tglx + */ +static int doc_ecc_decode(struct rs_control *rs, uint8_t *data, uint8_t *ecc) +{ + int i, j, nerr, errpos[8]; + uint8_t parity; + uint16_t ds[4], s[5], tmp, errval[8], syn[4]; + + memset(syn, 0, sizeof(syn)); + /* Convert the ecc bytes into words */ + ds[0] = ((ecc[4] & 0xff) >> 0) | ((ecc[5] & 0x03) << 8); + ds[1] = ((ecc[5] & 0xfc) >> 2) | ((ecc[2] & 0x0f) << 6); + ds[2] = ((ecc[2] & 0xf0) >> 4) | ((ecc[3] & 0x3f) << 4); + ds[3] = ((ecc[3] & 0xc0) >> 6) | ((ecc[0] & 0xff) << 2); + parity = ecc[1]; + + /* Initialize the syndrome buffer */ + for (i = 0; i < NROOTS; i++) + s[i] = ds[0]; + /* + * Evaluate + * s[i] = ds[3]x^3 + ds[2]x^2 + ds[1]x^1 + ds[0] + * where x = alpha^(FCR + i) + */ + for (j = 1; j < NROOTS; j++) { + if (ds[j] == 0) + continue; + tmp = rs->index_of[ds[j]]; + for (i = 0; i < NROOTS; i++) + s[i] ^= rs->alpha_to[rs_modnn(rs, tmp + (FCR + i) * j)]; + } + + /* Calc syn[i] = s[i] / alpha^(v + i) */ + for (i = 0; i < NROOTS; i++) { + if (s[i]) + syn[i] = rs_modnn(rs, rs->index_of[s[i]] + (NN - FCR - i)); + } + /* Call the decoder library */ + nerr = decode_rs16(rs, NULL, NULL, 1019, syn, 0, errpos, 0, errval); + + /* Incorrectable errors ? */ + if (nerr < 0) + return nerr; + + /* + * Correct the errors. The bitpositions are a bit of magic, + * but they are given by the design of the de/encoder circuit + * in the DoC ASIC's. + */ + for (i = 0; i < nerr; i++) { + int index, bitpos, pos = 1015 - errpos[i]; + uint8_t val; + if (pos >= NB_DATA && pos < 1019) + continue; + if (pos < NB_DATA) { + /* extract bit position (MSB first) */ + pos = 10 * (NB_DATA - 1 - pos) - 6; + /* now correct the following 10 bits. At most two bytes + can be modified since pos is even */ + index = (pos >> 3) ^ 1; + bitpos = pos & 7; + if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { + val = (uint8_t) (errval[i] >> (2 + bitpos)); + parity ^= val; + if (index < SECTOR_SIZE) + data[index] ^= val; + } + index = ((pos >> 3) + 1) ^ 1; + bitpos = (bitpos + 10) & 7; + if (bitpos == 0) + bitpos = 8; + if ((index >= 0 && index < SECTOR_SIZE) || index == (SECTOR_SIZE + 1)) { + val = (uint8_t) (errval[i] << (8 - bitpos)); + parity ^= val; + if (index < SECTOR_SIZE) + data[index] ^= val; + } + } + } + /* If the parity is wrong, no rescue possible */ + return parity ? -EBADMSG : nerr; +} + +static void DoC_Delay(struct doc_priv *doc, unsigned short cycles) +{ + volatile char dummy; + int i; + + for (i = 0; i < cycles; i++) { + if (DoC_is_Millennium(doc)) + dummy = ReadDOC(doc->virtadr, NOP); + else if (DoC_is_MillenniumPlus(doc)) + dummy = ReadDOC(doc->virtadr, Mplus_NOP); + else + dummy = ReadDOC(doc->virtadr, DOCStatus); + } + +} + +#define CDSN_CTRL_FR_B_MASK (CDSN_CTRL_FR_B0 | CDSN_CTRL_FR_B1) + +/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */ +static int _DoC_WaitReady(struct doc_priv *doc) +{ + void __iomem *docptr = doc->virtadr; + unsigned long timeo = jiffies + (HZ * 10); + + if (debug) + printk("_DoC_WaitReady...\n"); + /* Out-of-line routine to wait for chip response */ + if (DoC_is_MillenniumPlus(doc)) { + while ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { + if (time_after(jiffies, timeo)) { + printk("_DoC_WaitReady timed out.\n"); + return -EIO; + } + udelay(1); + cond_resched(); + } + } else { + while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { + if (time_after(jiffies, timeo)) { + printk("_DoC_WaitReady timed out.\n"); + return -EIO; + } + udelay(1); + cond_resched(); + } + } + + return 0; +} + +static inline int DoC_WaitReady(struct doc_priv *doc) +{ + void __iomem *docptr = doc->virtadr; + int ret = 0; + + if (DoC_is_MillenniumPlus(doc)) { + DoC_Delay(doc, 4); + + if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) + /* Call the out-of-line routine to wait */ + ret = _DoC_WaitReady(doc); + } else { + DoC_Delay(doc, 4); + + if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) + /* Call the out-of-line routine to wait */ + ret = _DoC_WaitReady(doc); + DoC_Delay(doc, 2); + } + + if (debug) + printk("DoC_WaitReady OK\n"); + return ret; +} + +static void doc2000_write_byte(struct mtd_info *mtd, u_char datum) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + if (debug) + printk("write_byte %02x\n", datum); + WriteDOC(datum, docptr, CDSNSlowIO); + WriteDOC(datum, docptr, 2k_CDSN_IO); +} + +static u_char doc2000_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + u_char ret; + + ReadDOC(docptr, CDSNSlowIO); + DoC_Delay(doc, 2); + ret = ReadDOC(docptr, 2k_CDSN_IO); + if (debug) + printk("read_byte returns %02x\n", ret); + return ret; +} + +static void doc2000_writebuf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + if (debug) + printk("writebuf of %d bytes: ", len); + for (i = 0; i < len; i++) { + WriteDOC_(buf[i], docptr, DoC_2k_CDSN_IO + i); + if (debug && i < 16) + printk("%02x ", buf[i]); + } + if (debug) + printk("\n"); +} + +static void doc2000_readbuf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + if (debug) + printk("readbuf of %d bytes: ", len); + + for (i = 0; i < len; i++) { + buf[i] = ReadDOC(docptr, 2k_CDSN_IO + i); + } +} + +static void doc2000_readbuf_dword(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + if (debug) + printk("readbuf_dword of %d bytes: ", len); + + if (unlikely((((unsigned long)buf) | len) & 3)) { + for (i = 0; i < len; i++) { + *(uint8_t *) (&buf[i]) = ReadDOC(docptr, 2k_CDSN_IO + i); + } + } else { + for (i = 0; i < len; i += 4) { + *(uint32_t *) (&buf[i]) = readl(docptr + DoC_2k_CDSN_IO + i); + } + } +} + +static uint16_t __init doc200x_ident_chip(struct mtd_info *mtd, int nr) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + uint16_t ret; + + doc200x_select_chip(mtd, nr); + doc200x_hwcontrol(mtd, NAND_CMD_READID, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + /* We can't use dev_ready here, but at least we wait for the + * command to complete + */ + udelay(50); + + ret = this->read_byte(mtd) << 8; + ret |= this->read_byte(mtd); + + if (doc->ChipID == DOC_ChipID_Doc2k && try_dword && !nr) { + /* First chip probe. See if we get same results by 32-bit access */ + union { + uint32_t dword; + uint8_t byte[4]; + } ident; + void __iomem *docptr = doc->virtadr; + + doc200x_hwcontrol(mtd, NAND_CMD_READID, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, 0, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + doc200x_hwcontrol(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + + udelay(50); + + ident.dword = readl(docptr + DoC_2k_CDSN_IO); + if (((ident.byte[0] << 8) | ident.byte[1]) == ret) { + printk(KERN_INFO "DiskOnChip 2000 responds to DWORD access\n"); + this->read_buf = &doc2000_readbuf_dword; + } + } + + return ret; +} + +static void __init doc2000_count_chips(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + uint16_t mfrid; + int i; + + /* Max 4 chips per floor on DiskOnChip 2000 */ + doc->chips_per_floor = 4; + + /* Find out what the first chip is */ + mfrid = doc200x_ident_chip(mtd, 0); + + /* Find how many chips in each floor. */ + for (i = 1; i < 4; i++) { + if (doc200x_ident_chip(mtd, i) != mfrid) + break; + } + doc->chips_per_floor = i; + printk(KERN_DEBUG "Detected %d chips per floor.\n", i); +} + +static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this) +{ + struct doc_priv *doc = this->priv; + + int status; + + DoC_WaitReady(doc); + this->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + DoC_WaitReady(doc); + status = (int)this->read_byte(mtd); + + return status; +} + +static void doc2001_write_byte(struct mtd_info *mtd, u_char datum) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + WriteDOC(datum, docptr, CDSNSlowIO); + WriteDOC(datum, docptr, Mil_CDSN_IO); + WriteDOC(datum, docptr, WritePipeTerm); +} + +static u_char doc2001_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + //ReadDOC(docptr, CDSNSlowIO); + /* 11.4.5 -- delay twice to allow extended length cycle */ + DoC_Delay(doc, 2); + ReadDOC(docptr, ReadPipeInit); + //return ReadDOC(docptr, Mil_CDSN_IO); + return ReadDOC(docptr, LastDataRead); +} + +static void doc2001_writebuf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + for (i = 0; i < len; i++) + WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); + /* Terminate write pipeline */ + WriteDOC(0x00, docptr, WritePipeTerm); +} + +static void doc2001_readbuf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + /* Start read pipeline */ + ReadDOC(docptr, ReadPipeInit); + + for (i = 0; i < len - 1; i++) + buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff)); + + /* Terminate read pipeline */ + buf[i] = ReadDOC(docptr, LastDataRead); +} + +static u_char doc2001plus_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + u_char ret; + + ReadDOC(docptr, Mplus_ReadPipeInit); + ReadDOC(docptr, Mplus_ReadPipeInit); + ret = ReadDOC(docptr, Mplus_LastDataRead); + if (debug) + printk("read_byte returns %02x\n", ret); + return ret; +} + +static void doc2001plus_writebuf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + if (debug) + printk("writebuf of %d bytes: ", len); + for (i = 0; i < len; i++) { + WriteDOC_(buf[i], docptr, DoC_Mil_CDSN_IO + i); + if (debug && i < 16) + printk("%02x ", buf[i]); + } + if (debug) + printk("\n"); +} + +static void doc2001plus_readbuf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + + if (debug) + printk("readbuf of %d bytes: ", len); + + /* Start read pipeline */ + ReadDOC(docptr, Mplus_ReadPipeInit); + ReadDOC(docptr, Mplus_ReadPipeInit); + + for (i = 0; i < len - 2; i++) { + buf[i] = ReadDOC(docptr, Mil_CDSN_IO); + if (debug && i < 16) + printk("%02x ", buf[i]); + } + + /* Terminate read pipeline */ + buf[len - 2] = ReadDOC(docptr, Mplus_LastDataRead); + if (debug && i < 16) + printk("%02x ", buf[len - 2]); + buf[len - 1] = ReadDOC(docptr, Mplus_LastDataRead); + if (debug && i < 16) + printk("%02x ", buf[len - 1]); + if (debug) + printk("\n"); +} + +static void doc2001plus_select_chip(struct mtd_info *mtd, int chip) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int floor = 0; + + if (debug) + printk("select chip (%d)\n", chip); + + if (chip == -1) { + /* Disable flash internally */ + WriteDOC(0, docptr, Mplus_FlashSelect); + return; + } + + floor = chip / doc->chips_per_floor; + chip -= (floor * doc->chips_per_floor); + + /* Assert ChipEnable and deassert WriteProtect */ + WriteDOC((DOC_FLASH_CE), docptr, Mplus_FlashSelect); + this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + doc->curchip = chip; + doc->curfloor = floor; +} + +static void doc200x_select_chip(struct mtd_info *mtd, int chip) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int floor = 0; + + if (debug) + printk("select chip (%d)\n", chip); + + if (chip == -1) + return; + + floor = chip / doc->chips_per_floor; + chip -= (floor * doc->chips_per_floor); + + /* 11.4.4 -- deassert CE before changing chip */ + doc200x_hwcontrol(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); + + WriteDOC(floor, docptr, FloorSelect); + WriteDOC(chip, docptr, CDSNDeviceSelect); + + doc200x_hwcontrol(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + doc->curchip = chip; + doc->curfloor = floor; +} + +#define CDSN_CTRL_MSK (CDSN_CTRL_CE | CDSN_CTRL_CLE | CDSN_CTRL_ALE) + +static void doc200x_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + if (ctrl & NAND_CTRL_CHANGE) { + doc->CDSNControl &= ~CDSN_CTRL_MSK; + doc->CDSNControl |= ctrl & CDSN_CTRL_MSK; + if (debug) + printk("hwcontrol(%d): %02x\n", cmd, doc->CDSNControl); + WriteDOC(doc->CDSNControl, docptr, CDSNControl); + /* 11.4.3 -- 4 NOPs after CSDNControl write */ + DoC_Delay(doc, 4); + } + if (cmd != NAND_CMD_NONE) { + if (DoC_is_2000(doc)) + doc2000_write_byte(mtd, cmd); + else + doc2001_write_byte(mtd, cmd); + } +} + +static void doc2001plus_command(struct mtd_info *mtd, unsigned command, int column, int page_addr) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + /* + * Must terminate write pipeline before sending any commands + * to the device. + */ + if (command == NAND_CMD_PAGEPROG) { + WriteDOC(0x00, docptr, Mplus_WritePipeTerm); + WriteDOC(0x00, docptr, Mplus_WritePipeTerm); + } + + /* + * Write out the command to the device. + */ + if (command == NAND_CMD_SEQIN) { + int readcmd; + + if (column >= mtd->writesize) { + /* OOB area */ + column -= mtd->writesize; + readcmd = NAND_CMD_READOOB; + } else if (column < 256) { + /* First 256 bytes --> READ0 */ + readcmd = NAND_CMD_READ0; + } else { + column -= 256; + readcmd = NAND_CMD_READ1; + } + WriteDOC(readcmd, docptr, Mplus_FlashCmd); + } + WriteDOC(command, docptr, Mplus_FlashCmd); + WriteDOC(0, docptr, Mplus_WritePipeTerm); + WriteDOC(0, docptr, Mplus_WritePipeTerm); + + if (column != -1 || page_addr != -1) { + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (this->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + WriteDOC(column, docptr, Mplus_FlashAddress); + } + if (page_addr != -1) { + WriteDOC((unsigned char)(page_addr & 0xff), docptr, Mplus_FlashAddress); + WriteDOC((unsigned char)((page_addr >> 8) & 0xff), docptr, Mplus_FlashAddress); + /* One more address cycle for higher density devices */ + if (this->chipsize & 0x0c000000) { + WriteDOC((unsigned char)((page_addr >> 16) & 0x0f), docptr, Mplus_FlashAddress); + printk("high density\n"); + } + } + WriteDOC(0, docptr, Mplus_WritePipeTerm); + WriteDOC(0, docptr, Mplus_WritePipeTerm); + /* deassert ALE */ + if (command == NAND_CMD_READ0 || command == NAND_CMD_READ1 || + command == NAND_CMD_READOOB || command == NAND_CMD_READID) + WriteDOC(0, docptr, Mplus_FlashControl); + } + + /* + * program and erase have their own busy handlers + * status and sequential in needs no delay + */ + switch (command) { + + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + if (this->dev_ready) + break; + udelay(this->chip_delay); + WriteDOC(NAND_CMD_STATUS, docptr, Mplus_FlashCmd); + WriteDOC(0, docptr, Mplus_WritePipeTerm); + WriteDOC(0, docptr, Mplus_WritePipeTerm); + while (!(this->read_byte(mtd) & 0x40)) ; + return; + + /* This applies to read commands */ + default: + /* + * If we don't have access to the busy pin, we apply the given + * command delay + */ + if (!this->dev_ready) { + udelay(this->chip_delay); + return; + } + } + + /* Apply this short delay always to ensure that we do wait tWB in + * any case on any machine. */ + ndelay(100); + /* wait until command is processed */ + while (!this->dev_ready(mtd)) ; +} + +static int doc200x_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + if (DoC_is_MillenniumPlus(doc)) { + /* 11.4.2 -- must NOP four times before checking FR/B# */ + DoC_Delay(doc, 4); + if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) { + if (debug) + printk("not ready\n"); + return 0; + } + if (debug) + printk("was ready\n"); + return 1; + } else { + /* 11.4.2 -- must NOP four times before checking FR/B# */ + DoC_Delay(doc, 4); + if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { + if (debug) + printk("not ready\n"); + return 0; + } + /* 11.4.2 -- Must NOP twice if it's ready */ + DoC_Delay(doc, 2); + if (debug) + printk("was ready\n"); + return 1; + } +} + +static int doc200x_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + /* This is our last resort if we couldn't find or create a BBT. Just + pretend all blocks are good. */ + return 0; +} + +static void doc200x_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + /* Prime the ECC engine */ + switch (mode) { + case NAND_ECC_READ: + WriteDOC(DOC_ECC_RESET, docptr, ECCConf); + WriteDOC(DOC_ECC_EN, docptr, ECCConf); + break; + case NAND_ECC_WRITE: + WriteDOC(DOC_ECC_RESET, docptr, ECCConf); + WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf); + break; + } +} + +static void doc2001plus_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + + /* Prime the ECC engine */ + switch (mode) { + case NAND_ECC_READ: + WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); + WriteDOC(DOC_ECC_EN, docptr, Mplus_ECCConf); + break; + case NAND_ECC_WRITE: + WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf); + WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, Mplus_ECCConf); + break; + } +} + +/* This code is only called on write */ +static int doc200x_calculate_ecc(struct mtd_info *mtd, const u_char *dat, unsigned char *ecc_code) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + int i; + int emptymatch = 1; + + /* flush the pipeline */ + if (DoC_is_2000(doc)) { + WriteDOC(doc->CDSNControl & ~CDSN_CTRL_FLASH_IO, docptr, CDSNControl); + WriteDOC(0, docptr, 2k_CDSN_IO); + WriteDOC(0, docptr, 2k_CDSN_IO); + WriteDOC(0, docptr, 2k_CDSN_IO); + WriteDOC(doc->CDSNControl, docptr, CDSNControl); + } else if (DoC_is_MillenniumPlus(doc)) { + WriteDOC(0, docptr, Mplus_NOP); + WriteDOC(0, docptr, Mplus_NOP); + WriteDOC(0, docptr, Mplus_NOP); + } else { + WriteDOC(0, docptr, NOP); + WriteDOC(0, docptr, NOP); + WriteDOC(0, docptr, NOP); + } + + for (i = 0; i < 6; i++) { + if (DoC_is_MillenniumPlus(doc)) + ecc_code[i] = ReadDOC_(docptr, DoC_Mplus_ECCSyndrome0 + i); + else + ecc_code[i] = ReadDOC_(docptr, DoC_ECCSyndrome0 + i); + if (ecc_code[i] != empty_write_ecc[i]) + emptymatch = 0; + } + if (DoC_is_MillenniumPlus(doc)) + WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf); + else + WriteDOC(DOC_ECC_DIS, docptr, ECCConf); +#if 0 + /* If emptymatch=1, we might have an all-0xff data buffer. Check. */ + if (emptymatch) { + /* Note: this somewhat expensive test should not be triggered + often. It could be optimized away by examining the data in + the writebuf routine, and remembering the result. */ + for (i = 0; i < 512; i++) { + if (dat[i] == 0xff) + continue; + emptymatch = 0; + break; + } + } + /* If emptymatch still =1, we do have an all-0xff data buffer. + Return all-0xff ecc value instead of the computed one, so + it'll look just like a freshly-erased page. */ + if (emptymatch) + memset(ecc_code, 0xff, 6); +#endif + return 0; +} + +static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *isnull) +{ + int i, ret = 0; + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + void __iomem *docptr = doc->virtadr; + uint8_t calc_ecc[6]; + volatile u_char dummy; + int emptymatch = 1; + + /* flush the pipeline */ + if (DoC_is_2000(doc)) { + dummy = ReadDOC(docptr, 2k_ECCStatus); + dummy = ReadDOC(docptr, 2k_ECCStatus); + dummy = ReadDOC(docptr, 2k_ECCStatus); + } else if (DoC_is_MillenniumPlus(doc)) { + dummy = ReadDOC(docptr, Mplus_ECCConf); + dummy = ReadDOC(docptr, Mplus_ECCConf); + dummy = ReadDOC(docptr, Mplus_ECCConf); + } else { + dummy = ReadDOC(docptr, ECCConf); + dummy = ReadDOC(docptr, ECCConf); + dummy = ReadDOC(docptr, ECCConf); + } + + /* Error occurred ? */ + if (dummy & 0x80) { + for (i = 0; i < 6; i++) { + if (DoC_is_MillenniumPlus(doc)) + calc_ecc[i] = ReadDOC_(docptr, DoC_Mplus_ECCSyndrome0 + i); + else + calc_ecc[i] = ReadDOC_(docptr, DoC_ECCSyndrome0 + i); + if (calc_ecc[i] != empty_read_syndrome[i]) + emptymatch = 0; + } + /* If emptymatch=1, the read syndrome is consistent with an + all-0xff data and stored ecc block. Check the stored ecc. */ + if (emptymatch) { + for (i = 0; i < 6; i++) { + if (read_ecc[i] == 0xff) + continue; + emptymatch = 0; + break; + } + } + /* If emptymatch still =1, check the data block. */ + if (emptymatch) { + /* Note: this somewhat expensive test should not be triggered + often. It could be optimized away by examining the data in + the readbuf routine, and remembering the result. */ + for (i = 0; i < 512; i++) { + if (dat[i] == 0xff) + continue; + emptymatch = 0; + break; + } + } + /* If emptymatch still =1, this is almost certainly a freshly- + erased block, in which case the ECC will not come out right. + We'll suppress the error and tell the caller everything's + OK. Because it is. */ + if (!emptymatch) + ret = doc_ecc_decode(rs_decoder, dat, calc_ecc); + if (ret > 0) + printk(KERN_ERR "doc200x_correct_data corrected %d errors\n", ret); + } + if (DoC_is_MillenniumPlus(doc)) + WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf); + else + WriteDOC(DOC_ECC_DIS, docptr, ECCConf); + if (no_ecc_failures && mtd_is_eccerr(ret)) { + printk(KERN_ERR "suppressing ECC failure\n"); + ret = 0; + } + return ret; +} + +//u_char mydatabuf[528]; + +/* The strange out-of-order .oobfree list below is a (possibly unneeded) + * attempt to retain compatibility. It used to read: + * .oobfree = { {8, 8} } + * Since that leaves two bytes unusable, it was changed. But the following + * scheme might affect existing jffs2 installs by moving the cleanmarker: + * .oobfree = { {6, 10} } + * jffs2 seems to handle the above gracefully, but the current scheme seems + * safer. The only problem with it is that any code that parses oobfree must + * be able to handle out-of-order segments. + */ +static struct nand_ecclayout doc200x_oobinfo = { + .eccbytes = 6, + .eccpos = {0, 1, 2, 3, 4, 5}, + .oobfree = {{8, 8}, {6, 2}} +}; + +/* Find the (I)NFTL Media Header, and optionally also the mirror media header. + On successful return, buf will contain a copy of the media header for + further processing. id is the string to scan for, and will presumably be + either "ANAND" or "BNAND". If findmirror=1, also look for the mirror media + header. The page #s of the found media headers are placed in mh0_page and + mh1_page in the DOC private structure. */ +static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const char *id, int findmirror) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + unsigned offs; + int ret; + size_t retlen; + + for (offs = 0; offs < mtd->size; offs += mtd->erasesize) { + ret = mtd_read(mtd, offs, mtd->writesize, &retlen, buf); + if (retlen != mtd->writesize) + continue; + if (ret) { + printk(KERN_WARNING "ECC error scanning DOC at 0x%x\n", offs); + } + if (memcmp(buf, id, 6)) + continue; + printk(KERN_INFO "Found DiskOnChip %s Media Header at 0x%x\n", id, offs); + if (doc->mh0_page == -1) { + doc->mh0_page = offs >> this->page_shift; + if (!findmirror) + return 1; + continue; + } + doc->mh1_page = offs >> this->page_shift; + return 2; + } + if (doc->mh0_page == -1) { + printk(KERN_WARNING "DiskOnChip %s Media Header not found.\n", id); + return 0; + } + /* Only one mediaheader was found. We want buf to contain a + mediaheader on return, so we'll have to re-read the one we found. */ + offs = doc->mh0_page << this->page_shift; + ret = mtd_read(mtd, offs, mtd->writesize, &retlen, buf); + if (retlen != mtd->writesize) { + /* Insanity. Give up. */ + printk(KERN_ERR "Read DiskOnChip Media Header once, but can't reread it???\n"); + return 0; + } + return 1; +} + +static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + int ret = 0; + u_char *buf; + struct NFTLMediaHeader *mh; + const unsigned psize = 1 << this->page_shift; + int numparts = 0; + unsigned blocks, maxblocks; + int offs, numheaders; + + buf = kmalloc(mtd->writesize, GFP_KERNEL); + if (!buf) { + return 0; + } + if (!(numheaders = find_media_headers(mtd, buf, "ANAND", 1))) + goto out; + mh = (struct NFTLMediaHeader *)buf; + + le16_to_cpus(&mh->NumEraseUnits); + le16_to_cpus(&mh->FirstPhysicalEUN); + le32_to_cpus(&mh->FormattedSize); + + printk(KERN_INFO " DataOrgID = %s\n" + " NumEraseUnits = %d\n" + " FirstPhysicalEUN = %d\n" + " FormattedSize = %d\n" + " UnitSizeFactor = %d\n", + mh->DataOrgID, mh->NumEraseUnits, + mh->FirstPhysicalEUN, mh->FormattedSize, + mh->UnitSizeFactor); + + blocks = mtd->size >> this->phys_erase_shift; + maxblocks = min(32768U, mtd->erasesize - psize); + + if (mh->UnitSizeFactor == 0x00) { + /* Auto-determine UnitSizeFactor. The constraints are: + - There can be at most 32768 virtual blocks. + - There can be at most (virtual block size - page size) + virtual blocks (because MediaHeader+BBT must fit in 1). + */ + mh->UnitSizeFactor = 0xff; + while (blocks > maxblocks) { + blocks >>= 1; + maxblocks = min(32768U, (maxblocks << 1) + psize); + mh->UnitSizeFactor--; + } + printk(KERN_WARNING "UnitSizeFactor=0x00 detected. Correct value is assumed to be 0x%02x.\n", mh->UnitSizeFactor); + } + + /* NOTE: The lines below modify internal variables of the NAND and MTD + layers; variables with have already been configured by nand_scan. + Unfortunately, we didn't know before this point what these values + should be. Thus, this code is somewhat dependent on the exact + implementation of the NAND layer. */ + if (mh->UnitSizeFactor != 0xff) { + this->bbt_erase_shift += (0xff - mh->UnitSizeFactor); + mtd->erasesize <<= (0xff - mh->UnitSizeFactor); + printk(KERN_INFO "Setting virtual erase size to %d\n", mtd->erasesize); + blocks = mtd->size >> this->bbt_erase_shift; + maxblocks = min(32768U, mtd->erasesize - psize); + } + + if (blocks > maxblocks) { + printk(KERN_ERR "UnitSizeFactor of 0x%02x is inconsistent with device size. Aborting.\n", mh->UnitSizeFactor); + goto out; + } + + /* Skip past the media headers. */ + offs = max(doc->mh0_page, doc->mh1_page); + offs <<= this->page_shift; + offs += mtd->erasesize; + + if (show_firmware_partition == 1) { + parts[0].name = " DiskOnChip Firmware / Media Header partition"; + parts[0].offset = 0; + parts[0].size = offs; + numparts = 1; + } + + parts[numparts].name = " DiskOnChip BDTL partition"; + parts[numparts].offset = offs; + parts[numparts].size = (mh->NumEraseUnits - numheaders) << this->bbt_erase_shift; + + offs += parts[numparts].size; + numparts++; + + if (offs < mtd->size) { + parts[numparts].name = " DiskOnChip Remainder partition"; + parts[numparts].offset = offs; + parts[numparts].size = mtd->size - offs; + numparts++; + } + + ret = numparts; + out: + kfree(buf); + return ret; +} + +/* This is a stripped-down copy of the code in inftlmount.c */ +static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partition *parts) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + int ret = 0; + u_char *buf; + struct INFTLMediaHeader *mh; + struct INFTLPartition *ip; + int numparts = 0; + int blocks; + int vshift, lastvunit = 0; + int i; + int end = mtd->size; + + if (inftl_bbt_write) + end -= (INFTL_BBT_RESERVED_BLOCKS << this->phys_erase_shift); + + buf = kmalloc(mtd->writesize, GFP_KERNEL); + if (!buf) { + return 0; + } + + if (!find_media_headers(mtd, buf, "BNAND", 0)) + goto out; + doc->mh1_page = doc->mh0_page + (4096 >> this->page_shift); + mh = (struct INFTLMediaHeader *)buf; + + le32_to_cpus(&mh->NoOfBootImageBlocks); + le32_to_cpus(&mh->NoOfBinaryPartitions); + le32_to_cpus(&mh->NoOfBDTLPartitions); + le32_to_cpus(&mh->BlockMultiplierBits); + le32_to_cpus(&mh->FormatFlags); + le32_to_cpus(&mh->PercentUsed); + + printk(KERN_INFO " bootRecordID = %s\n" + " NoOfBootImageBlocks = %d\n" + " NoOfBinaryPartitions = %d\n" + " NoOfBDTLPartitions = %d\n" + " BlockMultiplerBits = %d\n" + " FormatFlgs = %d\n" + " OsakVersion = %d.%d.%d.%d\n" + " PercentUsed = %d\n", + mh->bootRecordID, mh->NoOfBootImageBlocks, + mh->NoOfBinaryPartitions, + mh->NoOfBDTLPartitions, + mh->BlockMultiplierBits, mh->FormatFlags, + ((unsigned char *) &mh->OsakVersion)[0] & 0xf, + ((unsigned char *) &mh->OsakVersion)[1] & 0xf, + ((unsigned char *) &mh->OsakVersion)[2] & 0xf, + ((unsigned char *) &mh->OsakVersion)[3] & 0xf, + mh->PercentUsed); + + vshift = this->phys_erase_shift + mh->BlockMultiplierBits; + + blocks = mtd->size >> vshift; + if (blocks > 32768) { + printk(KERN_ERR "BlockMultiplierBits=%d is inconsistent with device size. Aborting.\n", mh->BlockMultiplierBits); + goto out; + } + + blocks = doc->chips_per_floor << (this->chip_shift - this->phys_erase_shift); + if (inftl_bbt_write && (blocks > mtd->erasesize)) { + printk(KERN_ERR "Writeable BBTs spanning more than one erase block are not yet supported. FIX ME!\n"); + goto out; + } + + /* Scan the partitions */ + for (i = 0; (i < 4); i++) { + ip = &(mh->Partitions[i]); + le32_to_cpus(&ip->virtualUnits); + le32_to_cpus(&ip->firstUnit); + le32_to_cpus(&ip->lastUnit); + le32_to_cpus(&ip->flags); + le32_to_cpus(&ip->spareUnits); + le32_to_cpus(&ip->Reserved0); + + printk(KERN_INFO " PARTITION[%d] ->\n" + " virtualUnits = %d\n" + " firstUnit = %d\n" + " lastUnit = %d\n" + " flags = 0x%x\n" + " spareUnits = %d\n", + i, ip->virtualUnits, ip->firstUnit, + ip->lastUnit, ip->flags, + ip->spareUnits); + + if ((show_firmware_partition == 1) && + (i == 0) && (ip->firstUnit > 0)) { + parts[0].name = " DiskOnChip IPL / Media Header partition"; + parts[0].offset = 0; + parts[0].size = mtd->erasesize * ip->firstUnit; + numparts = 1; + } + + if (ip->flags & INFTL_BINARY) + parts[numparts].name = " DiskOnChip BDK partition"; + else + parts[numparts].name = " DiskOnChip BDTL partition"; + parts[numparts].offset = ip->firstUnit << vshift; + parts[numparts].size = (1 + ip->lastUnit - ip->firstUnit) << vshift; + numparts++; + if (ip->lastUnit > lastvunit) + lastvunit = ip->lastUnit; + if (ip->flags & INFTL_LAST) + break; + } + lastvunit++; + if ((lastvunit << vshift) < end) { + parts[numparts].name = " DiskOnChip Remainder partition"; + parts[numparts].offset = lastvunit << vshift; + parts[numparts].size = end - parts[numparts].offset; + numparts++; + } + ret = numparts; + out: + kfree(buf); + return ret; +} + +static int __init nftl_scan_bbt(struct mtd_info *mtd) +{ + int ret, numparts; + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + struct mtd_partition parts[2]; + + memset((char *)parts, 0, sizeof(parts)); + /* On NFTL, we have to find the media headers before we can read the + BBTs, since they're stored in the media header eraseblocks. */ + numparts = nftl_partscan(mtd, parts); + if (!numparts) + return -EIO; + this->bbt_td->options = NAND_BBT_ABSPAGE | NAND_BBT_8BIT | + NAND_BBT_SAVECONTENT | NAND_BBT_WRITE | + NAND_BBT_VERSION; + this->bbt_td->veroffs = 7; + this->bbt_td->pages[0] = doc->mh0_page + 1; + if (doc->mh1_page != -1) { + this->bbt_md->options = NAND_BBT_ABSPAGE | NAND_BBT_8BIT | + NAND_BBT_SAVECONTENT | NAND_BBT_WRITE | + NAND_BBT_VERSION; + this->bbt_md->veroffs = 7; + this->bbt_md->pages[0] = doc->mh1_page + 1; + } else { + this->bbt_md = NULL; + } + + /* It's safe to set bd=NULL below because NAND_BBT_CREATE is not set. + At least as nand_bbt.c is currently written. */ + if ((ret = nand_scan_bbt(mtd, NULL))) + return ret; + mtd_device_register(mtd, NULL, 0); + if (!no_autopart) + mtd_device_register(mtd, parts, numparts); + return 0; +} + +static int __init inftl_scan_bbt(struct mtd_info *mtd) +{ + int ret, numparts; + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + struct mtd_partition parts[5]; + + if (this->numchips > doc->chips_per_floor) { + printk(KERN_ERR "Multi-floor INFTL devices not yet supported.\n"); + return -EIO; + } + + if (DoC_is_MillenniumPlus(doc)) { + this->bbt_td->options = NAND_BBT_2BIT | NAND_BBT_ABSPAGE; + if (inftl_bbt_write) + this->bbt_td->options |= NAND_BBT_WRITE; + this->bbt_td->pages[0] = 2; + this->bbt_md = NULL; + } else { + this->bbt_td->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; + if (inftl_bbt_write) + this->bbt_td->options |= NAND_BBT_WRITE; + this->bbt_td->offs = 8; + this->bbt_td->len = 8; + this->bbt_td->veroffs = 7; + this->bbt_td->maxblocks = INFTL_BBT_RESERVED_BLOCKS; + this->bbt_td->reserved_block_code = 0x01; + this->bbt_td->pattern = "MSYS_BBT"; + + this->bbt_md->options = NAND_BBT_LASTBLOCK | NAND_BBT_8BIT | NAND_BBT_VERSION; + if (inftl_bbt_write) + this->bbt_md->options |= NAND_BBT_WRITE; + this->bbt_md->offs = 8; + this->bbt_md->len = 8; + this->bbt_md->veroffs = 7; + this->bbt_md->maxblocks = INFTL_BBT_RESERVED_BLOCKS; + this->bbt_md->reserved_block_code = 0x01; + this->bbt_md->pattern = "TBB_SYSM"; + } + + /* It's safe to set bd=NULL below because NAND_BBT_CREATE is not set. + At least as nand_bbt.c is currently written. */ + if ((ret = nand_scan_bbt(mtd, NULL))) + return ret; + memset((char *)parts, 0, sizeof(parts)); + numparts = inftl_partscan(mtd, parts); + /* At least for now, require the INFTL Media Header. We could probably + do without it for non-INFTL use, since all it gives us is + autopartitioning, but I want to give it more thought. */ + if (!numparts) + return -EIO; + mtd_device_register(mtd, NULL, 0); + if (!no_autopart) + mtd_device_register(mtd, parts, numparts); + return 0; +} + +static inline int __init doc2000_init(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + + this->read_byte = doc2000_read_byte; + this->write_buf = doc2000_writebuf; + this->read_buf = doc2000_readbuf; + this->scan_bbt = nftl_scan_bbt; + + doc->CDSNControl = CDSN_CTRL_FLASH_IO | CDSN_CTRL_ECC_IO; + doc2000_count_chips(mtd); + mtd->name = "DiskOnChip 2000 (NFTL Model)"; + return (4 * doc->chips_per_floor); +} + +static inline int __init doc2001_init(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + + this->read_byte = doc2001_read_byte; + this->write_buf = doc2001_writebuf; + this->read_buf = doc2001_readbuf; + + ReadDOC(doc->virtadr, ChipID); + ReadDOC(doc->virtadr, ChipID); + ReadDOC(doc->virtadr, ChipID); + if (ReadDOC(doc->virtadr, ChipID) != DOC_ChipID_DocMil) { + /* It's not a Millennium; it's one of the newer + DiskOnChip 2000 units with a similar ASIC. + Treat it like a Millennium, except that it + can have multiple chips. */ + doc2000_count_chips(mtd); + mtd->name = "DiskOnChip 2000 (INFTL Model)"; + this->scan_bbt = inftl_scan_bbt; + return (4 * doc->chips_per_floor); + } else { + /* Bog-standard Millennium */ + doc->chips_per_floor = 1; + mtd->name = "DiskOnChip Millennium"; + this->scan_bbt = nftl_scan_bbt; + return 1; + } +} + +static inline int __init doc2001plus_init(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + struct doc_priv *doc = this->priv; + + this->read_byte = doc2001plus_read_byte; + this->write_buf = doc2001plus_writebuf; + this->read_buf = doc2001plus_readbuf; + this->scan_bbt = inftl_scan_bbt; + this->cmd_ctrl = NULL; + this->select_chip = doc2001plus_select_chip; + this->cmdfunc = doc2001plus_command; + this->ecc.hwctl = doc2001plus_enable_hwecc; + + doc->chips_per_floor = 1; + mtd->name = "DiskOnChip Millennium Plus"; + + return 1; +} + +static int __init doc_probe(unsigned long physadr) +{ + unsigned char ChipID; + struct mtd_info *mtd; + struct nand_chip *nand; + struct doc_priv *doc; + void __iomem *virtadr; + unsigned char save_control; + unsigned char tmp, tmpb, tmpc; + int reg, len, numchips; + int ret = 0; + + if (!request_mem_region(physadr, DOC_IOREMAP_LEN, "DiskOnChip")) + return -EBUSY; + virtadr = ioremap(physadr, DOC_IOREMAP_LEN); + if (!virtadr) { + printk(KERN_ERR "Diskonchip ioremap failed: 0x%x bytes at 0x%lx\n", DOC_IOREMAP_LEN, physadr); + ret = -EIO; + goto error_ioremap; + } + + /* It's not possible to cleanly detect the DiskOnChip - the + * bootup procedure will put the device into reset mode, and + * it's not possible to talk to it without actually writing + * to the DOCControl register. So we store the current contents + * of the DOCControl register's location, in case we later decide + * that it's not a DiskOnChip, and want to put it back how we + * found it. + */ + save_control = ReadDOC(virtadr, DOCControl); + + /* Reset the DiskOnChip ASIC */ + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET, virtadr, DOCControl); + + /* Enable the DiskOnChip ASIC */ + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); + WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL, virtadr, DOCControl); + + ChipID = ReadDOC(virtadr, ChipID); + + switch (ChipID) { + case DOC_ChipID_Doc2k: + reg = DoC_2k_ECCStatus; + break; + case DOC_ChipID_DocMil: + reg = DoC_ECCConf; + break; + case DOC_ChipID_DocMilPlus16: + case DOC_ChipID_DocMilPlus32: + case 0: + /* Possible Millennium Plus, need to do more checks */ + /* Possibly release from power down mode */ + for (tmp = 0; (tmp < 4); tmp++) + ReadDOC(virtadr, Mplus_Power); + + /* Reset the Millennium Plus ASIC */ + tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; + WriteDOC(tmp, virtadr, Mplus_DOCControl); + WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); + + mdelay(1); + /* Enable the Millennium Plus ASIC */ + tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT | DOC_MODE_BDECT; + WriteDOC(tmp, virtadr, Mplus_DOCControl); + WriteDOC(~tmp, virtadr, Mplus_CtrlConfirm); + mdelay(1); + + ChipID = ReadDOC(virtadr, ChipID); + + switch (ChipID) { + case DOC_ChipID_DocMilPlus16: + reg = DoC_Mplus_Toggle; + break; + case DOC_ChipID_DocMilPlus32: + printk(KERN_ERR "DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n"); + default: + ret = -ENODEV; + goto notfound; + } + break; + + default: + ret = -ENODEV; + goto notfound; + } + /* Check the TOGGLE bit in the ECC register */ + tmp = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; + tmpb = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; + tmpc = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT; + if ((tmp == tmpb) || (tmp != tmpc)) { + printk(KERN_WARNING "Possible DiskOnChip at 0x%lx failed TOGGLE test, dropping.\n", physadr); + ret = -ENODEV; + goto notfound; + } + + for (mtd = doclist; mtd; mtd = doc->nextdoc) { + unsigned char oldval; + unsigned char newval; + nand = mtd->priv; + doc = nand->priv; + /* Use the alias resolution register to determine if this is + in fact the same DOC aliased to a new address. If writes + to one chip's alias resolution register change the value on + the other chip, they're the same chip. */ + if (ChipID == DOC_ChipID_DocMilPlus16) { + oldval = ReadDOC(doc->virtadr, Mplus_AliasResolution); + newval = ReadDOC(virtadr, Mplus_AliasResolution); + } else { + oldval = ReadDOC(doc->virtadr, AliasResolution); + newval = ReadDOC(virtadr, AliasResolution); + } + if (oldval != newval) + continue; + if (ChipID == DOC_ChipID_DocMilPlus16) { + WriteDOC(~newval, virtadr, Mplus_AliasResolution); + oldval = ReadDOC(doc->virtadr, Mplus_AliasResolution); + WriteDOC(newval, virtadr, Mplus_AliasResolution); // restore it + } else { + WriteDOC(~newval, virtadr, AliasResolution); + oldval = ReadDOC(doc->virtadr, AliasResolution); + WriteDOC(newval, virtadr, AliasResolution); // restore it + } + newval = ~newval; + if (oldval == newval) { + printk(KERN_DEBUG "Found alias of DOC at 0x%lx to 0x%lx\n", doc->physadr, physadr); + goto notfound; + } + } + + printk(KERN_NOTICE "DiskOnChip found at 0x%lx\n", physadr); + + len = sizeof(struct mtd_info) + + sizeof(struct nand_chip) + sizeof(struct doc_priv) + (2 * sizeof(struct nand_bbt_descr)); + mtd = kzalloc(len, GFP_KERNEL); + if (!mtd) { + ret = -ENOMEM; + goto fail; + } + + nand = (struct nand_chip *) (mtd + 1); + doc = (struct doc_priv *) (nand + 1); + nand->bbt_td = (struct nand_bbt_descr *) (doc + 1); + nand->bbt_md = nand->bbt_td + 1; + + mtd->priv = nand; + mtd->owner = THIS_MODULE; + + nand->priv = doc; + nand->select_chip = doc200x_select_chip; + nand->cmd_ctrl = doc200x_hwcontrol; + nand->dev_ready = doc200x_dev_ready; + nand->waitfunc = doc200x_wait; + nand->block_bad = doc200x_block_bad; + nand->ecc.hwctl = doc200x_enable_hwecc; + nand->ecc.calculate = doc200x_calculate_ecc; + nand->ecc.correct = doc200x_correct_data; + + nand->ecc.layout = &doc200x_oobinfo; + nand->ecc.mode = NAND_ECC_HW_SYNDROME; + nand->ecc.size = 512; + nand->ecc.bytes = 6; + nand->ecc.strength = 2; + nand->bbt_options = NAND_BBT_USE_FLASH; + + doc->physadr = physadr; + doc->virtadr = virtadr; + doc->ChipID = ChipID; + doc->curfloor = -1; + doc->curchip = -1; + doc->mh0_page = -1; + doc->mh1_page = -1; + doc->nextdoc = doclist; + + if (ChipID == DOC_ChipID_Doc2k) + numchips = doc2000_init(mtd); + else if (ChipID == DOC_ChipID_DocMilPlus16) + numchips = doc2001plus_init(mtd); + else + numchips = doc2001_init(mtd); + + if ((ret = nand_scan(mtd, numchips))) { + /* DBB note: i believe nand_release is necessary here, as + buffers may have been allocated in nand_base. Check with + Thomas. FIX ME! */ + /* nand_release will call mtd_device_unregister, but we + haven't yet added it. This is handled without incident by + mtd_device_unregister, as far as I can tell. */ + nand_release(mtd); + kfree(mtd); + goto fail; + } + + /* Success! */ + doclist = mtd; + return 0; + + notfound: + /* Put back the contents of the DOCControl register, in case it's not + actually a DiskOnChip. */ + WriteDOC(save_control, virtadr, DOCControl); + fail: + iounmap(virtadr); + +error_ioremap: + release_mem_region(physadr, DOC_IOREMAP_LEN); + + return ret; +} + +static void release_nanddoc(void) +{ + struct mtd_info *mtd, *nextmtd; + struct nand_chip *nand; + struct doc_priv *doc; + + for (mtd = doclist; mtd; mtd = nextmtd) { + nand = mtd->priv; + doc = nand->priv; + + nextmtd = doc->nextdoc; + nand_release(mtd); + iounmap(doc->virtadr); + release_mem_region(doc->physadr, DOC_IOREMAP_LEN); + kfree(mtd); + } +} + +static int __init init_nanddoc(void) +{ + int i, ret = 0; + + /* We could create the decoder on demand, if memory is a concern. + * This way we have it handy, if an error happens + * + * Symbolsize is 10 (bits) + * Primitve polynomial is x^10+x^3+1 + * first consecutive root is 510 + * primitve element to generate roots = 1 + * generator polinomial degree = 4 + */ + rs_decoder = init_rs(10, 0x409, FCR, 1, NROOTS); + if (!rs_decoder) { + printk(KERN_ERR "DiskOnChip: Could not create a RS decoder\n"); + return -ENOMEM; + } + + if (doc_config_location) { + printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location); + ret = doc_probe(doc_config_location); + if (ret < 0) + goto outerr; + } else { + for (i = 0; (doc_locations[i] != 0xffffffff); i++) { + doc_probe(doc_locations[i]); + } + } + /* No banner message any more. Print a message if no DiskOnChip + found, so the user knows we at least tried. */ + if (!doclist) { + printk(KERN_INFO "No valid DiskOnChip devices found\n"); + ret = -ENODEV; + goto outerr; + } + return 0; + outerr: + free_rs(rs_decoder); + return ret; +} + +static void __exit cleanup_nanddoc(void) +{ + /* Cleanup the nand/DoC resources */ + release_nanddoc(); + + /* Free the reed solomon resources */ + if (rs_decoder) { + free_rs(rs_decoder); + } +} + +module_init(init_nanddoc); +module_exit(cleanup_nanddoc); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>"); +MODULE_DESCRIPTION("M-Systems DiskOnChip 2000, Millennium and Millennium Plus device driver"); diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c new file mode 100644 index 000000000..e5d7bcaaf --- /dev/null +++ b/drivers/mtd/nand/docg4.c @@ -0,0 +1,1393 @@ +/* + * Copyright © 2012 Mike Dunn <mikedunn@newsguy.com> + * + * mtd nand driver for M-Systems DiskOnChip G4 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Tested on the Palm Treo 680. The G4 is also present on Toshiba Portege, Asus + * P526, some HTC smartphones (Wizard, Prophet, ...), O2 XDA Zinc, maybe others. + * Should work on these as well. Let me know! + * + * TODO: + * + * Mechanism for management of password-protected areas + * + * Hamming ecc when reading oob only + * + * According to the M-Sys documentation, this device is also available in a + * "dual-die" configuration having a 256MB capacity, but no mechanism for + * detecting this variant is documented. Currently this driver assumes 128MB + * capacity. + * + * Support for multiple cascaded devices ("floors"). Not sure which gadgets + * contain multiple G4s in a cascaded configuration, if any. + * + */ + +#include <linux/kernel.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/string.h> +#include <linux/sched.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/export.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/bitops.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/bch.h> +#include <linux/bitrev.h> +#include <linux/jiffies.h> + +/* + * In "reliable mode" consecutive 2k pages are used in parallel (in some + * fashion) to store the same data. The data can be read back from the + * even-numbered pages in the normal manner; odd-numbered pages will appear to + * contain junk. Systems that boot from the docg4 typically write the secondary + * program loader (SPL) code in this mode. The SPL is loaded by the initial + * program loader (IPL, stored in the docg4's 2k NOR-like region that is mapped + * to the reset vector address). This module parameter enables you to use this + * driver to write the SPL. When in this mode, no more than 2k of data can be + * written at a time, because the addresses do not increment in the normal + * manner, and the starting offset must be within an even-numbered 2k region; + * i.e., invalid starting offsets are 0x800, 0xa00, 0xc00, 0xe00, 0x1800, + * 0x1a00, ... Reliable mode is a special case and should not be used unless + * you know what you're doing. + */ +static bool reliable_mode; +module_param(reliable_mode, bool, 0); +MODULE_PARM_DESC(reliable_mode, "pages are programmed in reliable mode"); + +/* + * You'll want to ignore badblocks if you're reading a partition that contains + * data written by the TrueFFS library (i.e., by PalmOS, Windows, etc), since + * it does not use mtd nand's method for marking bad blocks (using oob area). + * This will also skip the check of the "page written" flag. + */ +static bool ignore_badblocks; +module_param(ignore_badblocks, bool, 0); +MODULE_PARM_DESC(ignore_badblocks, "no badblock checking performed"); + +struct docg4_priv { + struct mtd_info *mtd; + struct device *dev; + void __iomem *virtadr; + int status; + struct { + unsigned int command; + int column; + int page; + } last_command; + uint8_t oob_buf[16]; + uint8_t ecc_buf[7]; + int oob_page; + struct bch_control *bch; +}; + +/* + * Defines prefixed with DOCG4 are unique to the diskonchip G4. All others are + * shared with other diskonchip devices (P3, G3 at least). + * + * Functions with names prefixed with docg4_ are mtd / nand interface functions + * (though they may also be called internally). All others are internal. + */ + +#define DOC_IOSPACE_DATA 0x0800 + +/* register offsets */ +#define DOC_CHIPID 0x1000 +#define DOC_DEVICESELECT 0x100a +#define DOC_ASICMODE 0x100c +#define DOC_DATAEND 0x101e +#define DOC_NOP 0x103e + +#define DOC_FLASHSEQUENCE 0x1032 +#define DOC_FLASHCOMMAND 0x1034 +#define DOC_FLASHADDRESS 0x1036 +#define DOC_FLASHCONTROL 0x1038 +#define DOC_ECCCONF0 0x1040 +#define DOC_ECCCONF1 0x1042 +#define DOC_HAMMINGPARITY 0x1046 +#define DOC_BCH_SYNDROM(idx) (0x1048 + idx) + +#define DOC_ASICMODECONFIRM 0x1072 +#define DOC_CHIPID_INV 0x1074 +#define DOC_POWERMODE 0x107c + +#define DOCG4_MYSTERY_REG 0x1050 + +/* apparently used only to write oob bytes 6 and 7 */ +#define DOCG4_OOB_6_7 0x1052 + +/* DOC_FLASHSEQUENCE register commands */ +#define DOC_SEQ_RESET 0x00 +#define DOCG4_SEQ_PAGE_READ 0x03 +#define DOCG4_SEQ_FLUSH 0x29 +#define DOCG4_SEQ_PAGEWRITE 0x16 +#define DOCG4_SEQ_PAGEPROG 0x1e +#define DOCG4_SEQ_BLOCKERASE 0x24 +#define DOCG4_SEQ_SETMODE 0x45 + +/* DOC_FLASHCOMMAND register commands */ +#define DOCG4_CMD_PAGE_READ 0x00 +#define DOC_CMD_ERASECYCLE2 0xd0 +#define DOCG4_CMD_FLUSH 0x70 +#define DOCG4_CMD_READ2 0x30 +#define DOC_CMD_PROG_BLOCK_ADDR 0x60 +#define DOCG4_CMD_PAGEWRITE 0x80 +#define DOC_CMD_PROG_CYCLE2 0x10 +#define DOCG4_CMD_FAST_MODE 0xa3 /* functionality guessed */ +#define DOC_CMD_RELIABLE_MODE 0x22 +#define DOC_CMD_RESET 0xff + +/* DOC_POWERMODE register bits */ +#define DOC_POWERDOWN_READY 0x80 + +/* DOC_FLASHCONTROL register bits */ +#define DOC_CTRL_CE 0x10 +#define DOC_CTRL_UNKNOWN 0x40 +#define DOC_CTRL_FLASHREADY 0x01 + +/* DOC_ECCCONF0 register bits */ +#define DOC_ECCCONF0_READ_MODE 0x8000 +#define DOC_ECCCONF0_UNKNOWN 0x2000 +#define DOC_ECCCONF0_ECC_ENABLE 0x1000 +#define DOC_ECCCONF0_DATA_BYTES_MASK 0x07ff + +/* DOC_ECCCONF1 register bits */ +#define DOC_ECCCONF1_BCH_SYNDROM_ERR 0x80 +#define DOC_ECCCONF1_ECC_ENABLE 0x07 +#define DOC_ECCCONF1_PAGE_IS_WRITTEN 0x20 + +/* DOC_ASICMODE register bits */ +#define DOC_ASICMODE_RESET 0x00 +#define DOC_ASICMODE_NORMAL 0x01 +#define DOC_ASICMODE_POWERDOWN 0x02 +#define DOC_ASICMODE_MDWREN 0x04 +#define DOC_ASICMODE_BDETCT_RESET 0x08 +#define DOC_ASICMODE_RSTIN_RESET 0x10 +#define DOC_ASICMODE_RAM_WE 0x20 + +/* good status values read after read/write/erase operations */ +#define DOCG4_PROGSTATUS_GOOD 0x51 +#define DOCG4_PROGSTATUS_GOOD_2 0xe0 + +/* + * On read operations (page and oob-only), the first byte read from I/O reg is a + * status. On error, it reads 0x73; otherwise, it reads either 0x71 (first read + * after reset only) or 0x51, so bit 1 is presumed to be an error indicator. + */ +#define DOCG4_READ_ERROR 0x02 /* bit 1 indicates read error */ + +/* anatomy of the device */ +#define DOCG4_CHIP_SIZE 0x8000000 +#define DOCG4_PAGE_SIZE 0x200 +#define DOCG4_PAGES_PER_BLOCK 0x200 +#define DOCG4_BLOCK_SIZE (DOCG4_PAGES_PER_BLOCK * DOCG4_PAGE_SIZE) +#define DOCG4_NUMBLOCKS (DOCG4_CHIP_SIZE / DOCG4_BLOCK_SIZE) +#define DOCG4_OOB_SIZE 0x10 +#define DOCG4_CHIP_SHIFT 27 /* log_2(DOCG4_CHIP_SIZE) */ +#define DOCG4_PAGE_SHIFT 9 /* log_2(DOCG4_PAGE_SIZE) */ +#define DOCG4_ERASE_SHIFT 18 /* log_2(DOCG4_BLOCK_SIZE) */ + +/* all but the last byte is included in ecc calculation */ +#define DOCG4_BCH_SIZE (DOCG4_PAGE_SIZE + DOCG4_OOB_SIZE - 1) + +#define DOCG4_USERDATA_LEN 520 /* 512 byte page plus 8 oob avail to user */ + +/* expected values from the ID registers */ +#define DOCG4_IDREG1_VALUE 0x0400 +#define DOCG4_IDREG2_VALUE 0xfbff + +/* primitive polynomial used to build the Galois field used by hw ecc gen */ +#define DOCG4_PRIMITIVE_POLY 0x4443 + +#define DOCG4_M 14 /* Galois field is of order 2^14 */ +#define DOCG4_T 4 /* BCH alg corrects up to 4 bit errors */ + +#define DOCG4_FACTORY_BBT_PAGE 16 /* page where read-only factory bbt lives */ +#define DOCG4_REDUNDANT_BBT_PAGE 24 /* page where redundant factory bbt lives */ + +/* + * Bytes 0, 1 are used as badblock marker. + * Bytes 2 - 6 are available to the user. + * Byte 7 is hamming ecc for first 7 oob bytes only. + * Bytes 8 - 14 are hw-generated ecc covering entire page + oob bytes 0 - 14. + * Byte 15 (the last) is used by the driver as a "page written" flag. + */ +static struct nand_ecclayout docg4_oobinfo = { + .eccbytes = 9, + .eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15}, + .oobavail = 5, + .oobfree = { {.offset = 2, .length = 5} } +}; + +/* + * The device has a nop register which M-Sys claims is for the purpose of + * inserting precise delays. But beware; at least some operations fail if the + * nop writes are replaced with a generic delay! + */ +static inline void write_nop(void __iomem *docptr) +{ + writew(0, docptr + DOC_NOP); +} + +static void docg4_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + int i; + struct nand_chip *nand = mtd->priv; + uint16_t *p = (uint16_t *) buf; + len >>= 1; + + for (i = 0; i < len; i++) + p[i] = readw(nand->IO_ADDR_R); +} + +static void docg4_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + int i; + struct nand_chip *nand = mtd->priv; + uint16_t *p = (uint16_t *) buf; + len >>= 1; + + for (i = 0; i < len; i++) + writew(p[i], nand->IO_ADDR_W); +} + +static int poll_status(struct docg4_priv *doc) +{ + /* + * Busy-wait for the FLASHREADY bit to be set in the FLASHCONTROL + * register. Operations known to take a long time (e.g., block erase) + * should sleep for a while before calling this. + */ + + uint16_t flash_status; + unsigned long timeo; + void __iomem *docptr = doc->virtadr; + + dev_dbg(doc->dev, "%s...\n", __func__); + + /* hardware quirk requires reading twice initially */ + flash_status = readw(docptr + DOC_FLASHCONTROL); + + timeo = jiffies + msecs_to_jiffies(200); /* generous timeout */ + do { + cpu_relax(); + flash_status = readb(docptr + DOC_FLASHCONTROL); + } while (!(flash_status & DOC_CTRL_FLASHREADY) && + time_before(jiffies, timeo)); + + if (unlikely(!(flash_status & DOC_CTRL_FLASHREADY))) { + dev_err(doc->dev, "%s: timed out!\n", __func__); + return NAND_STATUS_FAIL; + } + + return 0; +} + + +static int docg4_wait(struct mtd_info *mtd, struct nand_chip *nand) +{ + + struct docg4_priv *doc = nand->priv; + int status = NAND_STATUS_WP; /* inverse logic?? */ + dev_dbg(doc->dev, "%s...\n", __func__); + + /* report any previously unreported error */ + if (doc->status) { + status |= doc->status; + doc->status = 0; + return status; + } + + status |= poll_status(doc); + return status; +} + +static void docg4_select_chip(struct mtd_info *mtd, int chip) +{ + /* + * Select among multiple cascaded chips ("floors"). Multiple floors are + * not yet supported, so the only valid non-negative value is 0. + */ + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + + dev_dbg(doc->dev, "%s: chip %d\n", __func__, chip); + + if (chip < 0) + return; /* deselected */ + + if (chip > 0) + dev_warn(doc->dev, "multiple floors currently unsupported\n"); + + writew(0, docptr + DOC_DEVICESELECT); +} + +static void reset(struct mtd_info *mtd) +{ + /* full device reset */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + + writew(DOC_ASICMODE_RESET | DOC_ASICMODE_MDWREN, + docptr + DOC_ASICMODE); + writew(~(DOC_ASICMODE_RESET | DOC_ASICMODE_MDWREN), + docptr + DOC_ASICMODECONFIRM); + write_nop(docptr); + + writew(DOC_ASICMODE_NORMAL | DOC_ASICMODE_MDWREN, + docptr + DOC_ASICMODE); + writew(~(DOC_ASICMODE_NORMAL | DOC_ASICMODE_MDWREN), + docptr + DOC_ASICMODECONFIRM); + + writew(DOC_ECCCONF1_ECC_ENABLE, docptr + DOC_ECCCONF1); + + poll_status(doc); +} + +static void read_hw_ecc(void __iomem *docptr, uint8_t *ecc_buf) +{ + /* read the 7 hw-generated ecc bytes */ + + int i; + for (i = 0; i < 7; i++) { /* hw quirk; read twice */ + ecc_buf[i] = readb(docptr + DOC_BCH_SYNDROM(i)); + ecc_buf[i] = readb(docptr + DOC_BCH_SYNDROM(i)); + } +} + +static int correct_data(struct mtd_info *mtd, uint8_t *buf, int page) +{ + /* + * Called after a page read when hardware reports bitflips. + * Up to four bitflips can be corrected. + */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + int i, numerrs, errpos[4]; + const uint8_t blank_read_hwecc[8] = { + 0xcf, 0x72, 0xfc, 0x1b, 0xa9, 0xc7, 0xb9, 0 }; + + read_hw_ecc(docptr, doc->ecc_buf); /* read 7 hw-generated ecc bytes */ + + /* check if read error is due to a blank page */ + if (!memcmp(doc->ecc_buf, blank_read_hwecc, 7)) + return 0; /* yes */ + + /* skip additional check of "written flag" if ignore_badblocks */ + if (ignore_badblocks == false) { + + /* + * If the hw ecc bytes are not those of a blank page, there's + * still a chance that the page is blank, but was read with + * errors. Check the "written flag" in last oob byte, which + * is set to zero when a page is written. If more than half + * the bits are set, assume a blank page. Unfortunately, the + * bit flips(s) are not reported in stats. + */ + + if (nand->oob_poi[15]) { + int bit, numsetbits = 0; + unsigned long written_flag = nand->oob_poi[15]; + for_each_set_bit(bit, &written_flag, 8) + numsetbits++; + if (numsetbits > 4) { /* assume blank */ + dev_warn(doc->dev, + "error(s) in blank page " + "at offset %08x\n", + page * DOCG4_PAGE_SIZE); + return 0; + } + } + } + + /* + * The hardware ecc unit produces oob_ecc ^ calc_ecc. The kernel's bch + * algorithm is used to decode this. However the hw operates on page + * data in a bit order that is the reverse of that of the bch alg, + * requiring that the bits be reversed on the result. Thanks to Ivan + * Djelic for his analysis! + */ + for (i = 0; i < 7; i++) + doc->ecc_buf[i] = bitrev8(doc->ecc_buf[i]); + + numerrs = decode_bch(doc->bch, NULL, DOCG4_USERDATA_LEN, NULL, + doc->ecc_buf, NULL, errpos); + + if (numerrs == -EBADMSG) { + dev_warn(doc->dev, "uncorrectable errors at offset %08x\n", + page * DOCG4_PAGE_SIZE); + return -EBADMSG; + } + + BUG_ON(numerrs < 0); /* -EINVAL, or anything other than -EBADMSG */ + + /* undo last step in BCH alg (modulo mirroring not needed) */ + for (i = 0; i < numerrs; i++) + errpos[i] = (errpos[i] & ~7)|(7-(errpos[i] & 7)); + + /* fix the errors */ + for (i = 0; i < numerrs; i++) { + + /* ignore if error within oob ecc bytes */ + if (errpos[i] > DOCG4_USERDATA_LEN * 8) + continue; + + /* if error within oob area preceeding ecc bytes... */ + if (errpos[i] > DOCG4_PAGE_SIZE * 8) + change_bit(errpos[i] - DOCG4_PAGE_SIZE * 8, + (unsigned long *)nand->oob_poi); + + else /* error in page data */ + change_bit(errpos[i], (unsigned long *)buf); + } + + dev_notice(doc->dev, "%d error(s) corrected at offset %08x\n", + numerrs, page * DOCG4_PAGE_SIZE); + + return numerrs; +} + +static uint8_t docg4_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + + dev_dbg(doc->dev, "%s\n", __func__); + + if (doc->last_command.command == NAND_CMD_STATUS) { + int status; + + /* + * Previous nand command was status request, so nand + * infrastructure code expects to read the status here. If an + * error occurred in a previous operation, report it. + */ + doc->last_command.command = 0; + + if (doc->status) { + status = doc->status; + doc->status = 0; + } + + /* why is NAND_STATUS_WP inverse logic?? */ + else + status = NAND_STATUS_WP | NAND_STATUS_READY; + + return status; + } + + dev_warn(doc->dev, "unexpected call to read_byte()\n"); + + return 0; +} + +static void write_addr(struct docg4_priv *doc, uint32_t docg4_addr) +{ + /* write the four address bytes packed in docg4_addr to the device */ + + void __iomem *docptr = doc->virtadr; + writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS); + docg4_addr >>= 8; + writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS); + docg4_addr >>= 8; + writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS); + docg4_addr >>= 8; + writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS); +} + +static int read_progstatus(struct docg4_priv *doc) +{ + /* + * This apparently checks the status of programming. Done after an + * erasure, and after page data is written. On error, the status is + * saved, to be later retrieved by the nand infrastructure code. + */ + void __iomem *docptr = doc->virtadr; + + /* status is read from the I/O reg */ + uint16_t status1 = readw(docptr + DOC_IOSPACE_DATA); + uint16_t status2 = readw(docptr + DOC_IOSPACE_DATA); + uint16_t status3 = readw(docptr + DOCG4_MYSTERY_REG); + + dev_dbg(doc->dev, "docg4: %s: %02x %02x %02x\n", + __func__, status1, status2, status3); + + if (status1 != DOCG4_PROGSTATUS_GOOD + || status2 != DOCG4_PROGSTATUS_GOOD_2 + || status3 != DOCG4_PROGSTATUS_GOOD_2) { + doc->status = NAND_STATUS_FAIL; + dev_warn(doc->dev, "read_progstatus failed: " + "%02x, %02x, %02x\n", status1, status2, status3); + return -EIO; + } + return 0; +} + +static int pageprog(struct mtd_info *mtd) +{ + /* + * Final step in writing a page. Writes the contents of its + * internal buffer out to the flash array, or some such. + */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + int retval = 0; + + dev_dbg(doc->dev, "docg4: %s\n", __func__); + + writew(DOCG4_SEQ_PAGEPROG, docptr + DOC_FLASHSEQUENCE); + writew(DOC_CMD_PROG_CYCLE2, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + write_nop(docptr); + + /* Just busy-wait; usleep_range() slows things down noticeably. */ + poll_status(doc); + + writew(DOCG4_SEQ_FLUSH, docptr + DOC_FLASHSEQUENCE); + writew(DOCG4_CMD_FLUSH, docptr + DOC_FLASHCOMMAND); + writew(DOC_ECCCONF0_READ_MODE | 4, docptr + DOC_ECCCONF0); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + + retval = read_progstatus(doc); + writew(0, docptr + DOC_DATAEND); + write_nop(docptr); + poll_status(doc); + write_nop(docptr); + + return retval; +} + +static void sequence_reset(struct mtd_info *mtd) +{ + /* common starting sequence for all operations */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + + writew(DOC_CTRL_UNKNOWN | DOC_CTRL_CE, docptr + DOC_FLASHCONTROL); + writew(DOC_SEQ_RESET, docptr + DOC_FLASHSEQUENCE); + writew(DOC_CMD_RESET, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + write_nop(docptr); + poll_status(doc); + write_nop(docptr); +} + +static void read_page_prologue(struct mtd_info *mtd, uint32_t docg4_addr) +{ + /* first step in reading a page */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + + dev_dbg(doc->dev, + "docg4: %s: g4 page %08x\n", __func__, docg4_addr); + + sequence_reset(mtd); + + writew(DOCG4_SEQ_PAGE_READ, docptr + DOC_FLASHSEQUENCE); + writew(DOCG4_CMD_PAGE_READ, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + + write_addr(doc, docg4_addr); + + write_nop(docptr); + writew(DOCG4_CMD_READ2, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + write_nop(docptr); + + poll_status(doc); +} + +static void write_page_prologue(struct mtd_info *mtd, uint32_t docg4_addr) +{ + /* first step in writing a page */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + + dev_dbg(doc->dev, + "docg4: %s: g4 addr: %x\n", __func__, docg4_addr); + sequence_reset(mtd); + + if (unlikely(reliable_mode)) { + writew(DOCG4_SEQ_SETMODE, docptr + DOC_FLASHSEQUENCE); + writew(DOCG4_CMD_FAST_MODE, docptr + DOC_FLASHCOMMAND); + writew(DOC_CMD_RELIABLE_MODE, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + } + + writew(DOCG4_SEQ_PAGEWRITE, docptr + DOC_FLASHSEQUENCE); + writew(DOCG4_CMD_PAGEWRITE, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + write_addr(doc, docg4_addr); + write_nop(docptr); + write_nop(docptr); + poll_status(doc); +} + +static uint32_t mtd_to_docg4_address(int page, int column) +{ + /* + * Convert mtd address to format used by the device, 32 bit packed. + * + * Some notes on G4 addressing... The M-Sys documentation on this device + * claims that pages are 2K in length, and indeed, the format of the + * address used by the device reflects that. But within each page are + * four 512 byte "sub-pages", each with its own oob data that is + * read/written immediately after the 512 bytes of page data. This oob + * data contains the ecc bytes for the preceeding 512 bytes. + * + * Rather than tell the mtd nand infrastructure that page size is 2k, + * with four sub-pages each, we engage in a little subterfuge and tell + * the infrastructure code that pages are 512 bytes in size. This is + * done because during the course of reverse-engineering the device, I + * never observed an instance where an entire 2K "page" was read or + * written as a unit. Each "sub-page" is always addressed individually, + * its data read/written, and ecc handled before the next "sub-page" is + * addressed. + * + * This requires us to convert addresses passed by the mtd nand + * infrastructure code to those used by the device. + * + * The address that is written to the device consists of four bytes: the + * first two are the 2k page number, and the second is the index into + * the page. The index is in terms of 16-bit half-words and includes + * the preceeding oob data, so e.g., the index into the second + * "sub-page" is 0x108, and the full device address of the start of mtd + * page 0x201 is 0x00800108. + */ + int g4_page = page / 4; /* device's 2K page */ + int g4_index = (page % 4) * 0x108 + column/2; /* offset into page */ + return (g4_page << 16) | g4_index; /* pack */ +} + +static void docg4_command(struct mtd_info *mtd, unsigned command, int column, + int page_addr) +{ + /* handle standard nand commands */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + uint32_t g4_addr = mtd_to_docg4_address(page_addr, column); + + dev_dbg(doc->dev, "%s %x, page_addr=%x, column=%x\n", + __func__, command, page_addr, column); + + /* + * Save the command and its arguments. This enables emulation of + * standard flash devices, and also some optimizations. + */ + doc->last_command.command = command; + doc->last_command.column = column; + doc->last_command.page = page_addr; + + switch (command) { + + case NAND_CMD_RESET: + reset(mtd); + break; + + case NAND_CMD_READ0: + read_page_prologue(mtd, g4_addr); + break; + + case NAND_CMD_STATUS: + /* next call to read_byte() will expect a status */ + break; + + case NAND_CMD_SEQIN: + if (unlikely(reliable_mode)) { + uint16_t g4_page = g4_addr >> 16; + + /* writes to odd-numbered 2k pages are invalid */ + if (g4_page & 0x01) + dev_warn(doc->dev, + "invalid reliable mode address\n"); + } + + write_page_prologue(mtd, g4_addr); + + /* hack for deferred write of oob bytes */ + if (doc->oob_page == page_addr) + memcpy(nand->oob_poi, doc->oob_buf, 16); + break; + + case NAND_CMD_PAGEPROG: + pageprog(mtd); + break; + + /* we don't expect these, based on review of nand_base.c */ + case NAND_CMD_READOOB: + case NAND_CMD_READID: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + dev_warn(doc->dev, "docg4_command: " + "unexpected nand command 0x%x\n", command); + break; + + } +} + +static int read_page(struct mtd_info *mtd, struct nand_chip *nand, + uint8_t *buf, int page, bool use_ecc) +{ + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + uint16_t status, edc_err, *buf16; + int bits_corrected = 0; + + dev_dbg(doc->dev, "%s: page %08x\n", __func__, page); + + writew(DOC_ECCCONF0_READ_MODE | + DOC_ECCCONF0_ECC_ENABLE | + DOC_ECCCONF0_UNKNOWN | + DOCG4_BCH_SIZE, + docptr + DOC_ECCCONF0); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + + /* the 1st byte from the I/O reg is a status; the rest is page data */ + status = readw(docptr + DOC_IOSPACE_DATA); + if (status & DOCG4_READ_ERROR) { + dev_err(doc->dev, + "docg4_read_page: bad status: 0x%02x\n", status); + writew(0, docptr + DOC_DATAEND); + return -EIO; + } + + dev_dbg(doc->dev, "%s: status = 0x%x\n", __func__, status); + + docg4_read_buf(mtd, buf, DOCG4_PAGE_SIZE); /* read the page data */ + + /* this device always reads oob after page data */ + /* first 14 oob bytes read from I/O reg */ + docg4_read_buf(mtd, nand->oob_poi, 14); + + /* last 2 read from another reg */ + buf16 = (uint16_t *)(nand->oob_poi + 14); + *buf16 = readw(docptr + DOCG4_MYSTERY_REG); + + write_nop(docptr); + + if (likely(use_ecc == true)) { + + /* read the register that tells us if bitflip(s) detected */ + edc_err = readw(docptr + DOC_ECCCONF1); + edc_err = readw(docptr + DOC_ECCCONF1); + dev_dbg(doc->dev, "%s: edc_err = 0x%02x\n", __func__, edc_err); + + /* If bitflips are reported, attempt to correct with ecc */ + if (edc_err & DOC_ECCCONF1_BCH_SYNDROM_ERR) { + bits_corrected = correct_data(mtd, buf, page); + if (bits_corrected == -EBADMSG) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += bits_corrected; + } + } + + writew(0, docptr + DOC_DATAEND); + if (bits_corrected == -EBADMSG) /* uncorrectable errors */ + return 0; + return bits_corrected; +} + + +static int docg4_read_page_raw(struct mtd_info *mtd, struct nand_chip *nand, + uint8_t *buf, int oob_required, int page) +{ + return read_page(mtd, nand, buf, page, false); +} + +static int docg4_read_page(struct mtd_info *mtd, struct nand_chip *nand, + uint8_t *buf, int oob_required, int page) +{ + return read_page(mtd, nand, buf, page, true); +} + +static int docg4_read_oob(struct mtd_info *mtd, struct nand_chip *nand, + int page) +{ + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + uint16_t status; + + dev_dbg(doc->dev, "%s: page %x\n", __func__, page); + + docg4_command(mtd, NAND_CMD_READ0, nand->ecc.size, page); + + writew(DOC_ECCCONF0_READ_MODE | DOCG4_OOB_SIZE, docptr + DOC_ECCCONF0); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + + /* the 1st byte from the I/O reg is a status; the rest is oob data */ + status = readw(docptr + DOC_IOSPACE_DATA); + if (status & DOCG4_READ_ERROR) { + dev_warn(doc->dev, + "docg4_read_oob failed: status = 0x%02x\n", status); + return -EIO; + } + + dev_dbg(doc->dev, "%s: status = 0x%x\n", __func__, status); + + docg4_read_buf(mtd, nand->oob_poi, 16); + + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + writew(0, docptr + DOC_DATAEND); + write_nop(docptr); + + return 0; +} + +static int docg4_erase_block(struct mtd_info *mtd, int page) +{ + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + uint16_t g4_page; + + dev_dbg(doc->dev, "%s: page %04x\n", __func__, page); + + sequence_reset(mtd); + + writew(DOCG4_SEQ_BLOCKERASE, docptr + DOC_FLASHSEQUENCE); + writew(DOC_CMD_PROG_BLOCK_ADDR, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + + /* only 2 bytes of address are written to specify erase block */ + g4_page = (uint16_t)(page / 4); /* to g4's 2k page addressing */ + writeb(g4_page & 0xff, docptr + DOC_FLASHADDRESS); + g4_page >>= 8; + writeb(g4_page & 0xff, docptr + DOC_FLASHADDRESS); + write_nop(docptr); + + /* start the erasure */ + writew(DOC_CMD_ERASECYCLE2, docptr + DOC_FLASHCOMMAND); + write_nop(docptr); + write_nop(docptr); + + usleep_range(500, 1000); /* erasure is long; take a snooze */ + poll_status(doc); + writew(DOCG4_SEQ_FLUSH, docptr + DOC_FLASHSEQUENCE); + writew(DOCG4_CMD_FLUSH, docptr + DOC_FLASHCOMMAND); + writew(DOC_ECCCONF0_READ_MODE | 4, docptr + DOC_ECCCONF0); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + write_nop(docptr); + + read_progstatus(doc); + + writew(0, docptr + DOC_DATAEND); + write_nop(docptr); + poll_status(doc); + write_nop(docptr); + + return nand->waitfunc(mtd, nand); +} + +static int write_page(struct mtd_info *mtd, struct nand_chip *nand, + const uint8_t *buf, bool use_ecc) +{ + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + uint8_t ecc_buf[8]; + + dev_dbg(doc->dev, "%s...\n", __func__); + + writew(DOC_ECCCONF0_ECC_ENABLE | + DOC_ECCCONF0_UNKNOWN | + DOCG4_BCH_SIZE, + docptr + DOC_ECCCONF0); + write_nop(docptr); + + /* write the page data */ + docg4_write_buf16(mtd, buf, DOCG4_PAGE_SIZE); + + /* oob bytes 0 through 5 are written to I/O reg */ + docg4_write_buf16(mtd, nand->oob_poi, 6); + + /* oob byte 6 written to a separate reg */ + writew(nand->oob_poi[6], docptr + DOCG4_OOB_6_7); + + write_nop(docptr); + write_nop(docptr); + + /* write hw-generated ecc bytes to oob */ + if (likely(use_ecc == true)) { + /* oob byte 7 is hamming code */ + uint8_t hamming = readb(docptr + DOC_HAMMINGPARITY); + hamming = readb(docptr + DOC_HAMMINGPARITY); /* 2nd read */ + writew(hamming, docptr + DOCG4_OOB_6_7); + write_nop(docptr); + + /* read the 7 bch bytes from ecc regs */ + read_hw_ecc(docptr, ecc_buf); + ecc_buf[7] = 0; /* clear the "page written" flag */ + } + + /* write user-supplied bytes to oob */ + else { + writew(nand->oob_poi[7], docptr + DOCG4_OOB_6_7); + write_nop(docptr); + memcpy(ecc_buf, &nand->oob_poi[8], 8); + } + + docg4_write_buf16(mtd, ecc_buf, 8); + write_nop(docptr); + write_nop(docptr); + writew(0, docptr + DOC_DATAEND); + write_nop(docptr); + + return 0; +} + +static int docg4_write_page_raw(struct mtd_info *mtd, struct nand_chip *nand, + const uint8_t *buf, int oob_required) +{ + return write_page(mtd, nand, buf, false); +} + +static int docg4_write_page(struct mtd_info *mtd, struct nand_chip *nand, + const uint8_t *buf, int oob_required) +{ + return write_page(mtd, nand, buf, true); +} + +static int docg4_write_oob(struct mtd_info *mtd, struct nand_chip *nand, + int page) +{ + /* + * Writing oob-only is not really supported, because MLC nand must write + * oob bytes at the same time as page data. Nonetheless, we save the + * oob buffer contents here, and then write it along with the page data + * if the same page is subsequently written. This allows user space + * utilities that write the oob data prior to the page data to work + * (e.g., nandwrite). The disdvantage is that, if the intention was to + * write oob only, the operation is quietly ignored. Also, oob can get + * corrupted if two concurrent processes are running nandwrite. + */ + + /* note that bytes 7..14 are hw generated hamming/ecc and overwritten */ + struct docg4_priv *doc = nand->priv; + doc->oob_page = page; + memcpy(doc->oob_buf, nand->oob_poi, 16); + return 0; +} + +static int __init read_factory_bbt(struct mtd_info *mtd) +{ + /* + * The device contains a read-only factory bad block table. Read it and + * update the memory-based bbt accordingly. + */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + uint32_t g4_addr = mtd_to_docg4_address(DOCG4_FACTORY_BBT_PAGE, 0); + uint8_t *buf; + int i, block; + __u32 eccfailed_stats = mtd->ecc_stats.failed; + + buf = kzalloc(DOCG4_PAGE_SIZE, GFP_KERNEL); + if (buf == NULL) + return -ENOMEM; + + read_page_prologue(mtd, g4_addr); + docg4_read_page(mtd, nand, buf, 0, DOCG4_FACTORY_BBT_PAGE); + + /* + * If no memory-based bbt was created, exit. This will happen if module + * parameter ignore_badblocks is set. Then why even call this function? + * For an unknown reason, block erase always fails if it's the first + * operation after device power-up. The above read ensures it never is. + * Ugly, I know. + */ + if (nand->bbt == NULL) /* no memory-based bbt */ + goto exit; + + if (mtd->ecc_stats.failed > eccfailed_stats) { + /* + * Whoops, an ecc failure ocurred reading the factory bbt. + * It is stored redundantly, so we get another chance. + */ + eccfailed_stats = mtd->ecc_stats.failed; + docg4_read_page(mtd, nand, buf, 0, DOCG4_REDUNDANT_BBT_PAGE); + if (mtd->ecc_stats.failed > eccfailed_stats) { + dev_warn(doc->dev, + "The factory bbt could not be read!\n"); + goto exit; + } + } + + /* + * Parse factory bbt and update memory-based bbt. Factory bbt format is + * simple: one bit per block, block numbers increase left to right (msb + * to lsb). Bit clear means bad block. + */ + for (i = block = 0; block < DOCG4_NUMBLOCKS; block += 8, i++) { + int bitnum; + unsigned long bits = ~buf[i]; + for_each_set_bit(bitnum, &bits, 8) { + int badblock = block + 7 - bitnum; + nand->bbt[badblock / 4] |= + 0x03 << ((badblock % 4) * 2); + mtd->ecc_stats.badblocks++; + dev_notice(doc->dev, "factory-marked bad block: %d\n", + badblock); + } + } + exit: + kfree(buf); + return 0; +} + +static int docg4_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + /* + * Mark a block as bad. Bad blocks are marked in the oob area of the + * first page of the block. The default scan_bbt() in the nand + * infrastructure code works fine for building the memory-based bbt + * during initialization, as does the nand infrastructure function that + * checks if a block is bad by reading the bbt. This function replaces + * the nand default because writes to oob-only are not supported. + */ + + int ret, i; + uint8_t *buf; + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + struct nand_bbt_descr *bbtd = nand->badblock_pattern; + int page = (int)(ofs >> nand->page_shift); + uint32_t g4_addr = mtd_to_docg4_address(page, 0); + + dev_dbg(doc->dev, "%s: %08llx\n", __func__, ofs); + + if (unlikely(ofs & (DOCG4_BLOCK_SIZE - 1))) + dev_warn(doc->dev, "%s: ofs %llx not start of block!\n", + __func__, ofs); + + /* allocate blank buffer for page data */ + buf = kzalloc(DOCG4_PAGE_SIZE, GFP_KERNEL); + if (buf == NULL) + return -ENOMEM; + + /* write bit-wise negation of pattern to oob buffer */ + memset(nand->oob_poi, 0xff, mtd->oobsize); + for (i = 0; i < bbtd->len; i++) + nand->oob_poi[bbtd->offs + i] = ~bbtd->pattern[i]; + + /* write first page of block */ + write_page_prologue(mtd, g4_addr); + docg4_write_page(mtd, nand, buf, 1); + ret = pageprog(mtd); + + kfree(buf); + + return ret; +} + +static int docg4_block_neverbad(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + /* only called when module_param ignore_badblocks is set */ + return 0; +} + +static int docg4_suspend(struct platform_device *pdev, pm_message_t state) +{ + /* + * Put the device into "deep power-down" mode. Note that CE# must be + * deasserted for this to take effect. The xscale, e.g., can be + * configured to float this signal when the processor enters power-down, + * and a suitable pull-up ensures its deassertion. + */ + + int i; + uint8_t pwr_down; + struct docg4_priv *doc = platform_get_drvdata(pdev); + void __iomem *docptr = doc->virtadr; + + dev_dbg(doc->dev, "%s...\n", __func__); + + /* poll the register that tells us we're ready to go to sleep */ + for (i = 0; i < 10; i++) { + pwr_down = readb(docptr + DOC_POWERMODE); + if (pwr_down & DOC_POWERDOWN_READY) + break; + usleep_range(1000, 4000); + } + + if (pwr_down & DOC_POWERDOWN_READY) { + dev_err(doc->dev, "suspend failed; " + "timeout polling DOC_POWERDOWN_READY\n"); + return -EIO; + } + + writew(DOC_ASICMODE_POWERDOWN | DOC_ASICMODE_MDWREN, + docptr + DOC_ASICMODE); + writew(~(DOC_ASICMODE_POWERDOWN | DOC_ASICMODE_MDWREN), + docptr + DOC_ASICMODECONFIRM); + + write_nop(docptr); + + return 0; +} + +static int docg4_resume(struct platform_device *pdev) +{ + + /* + * Exit power-down. Twelve consecutive reads of the address below + * accomplishes this, assuming CE# has been asserted. + */ + + struct docg4_priv *doc = platform_get_drvdata(pdev); + void __iomem *docptr = doc->virtadr; + int i; + + dev_dbg(doc->dev, "%s...\n", __func__); + + for (i = 0; i < 12; i++) + readb(docptr + 0x1fff); + + return 0; +} + +static void __init init_mtd_structs(struct mtd_info *mtd) +{ + /* initialize mtd and nand data structures */ + + /* + * Note that some of the following initializations are not usually + * required within a nand driver because they are performed by the nand + * infrastructure code as part of nand_scan(). In this case they need + * to be initialized here because we skip call to nand_scan_ident() (the + * first half of nand_scan()). The call to nand_scan_ident() is skipped + * because for this device the chip id is not read in the manner of a + * standard nand device. Unfortunately, nand_scan_ident() does other + * things as well, such as call nand_set_defaults(). + */ + + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + + mtd->size = DOCG4_CHIP_SIZE; + mtd->name = "Msys_Diskonchip_G4"; + mtd->writesize = DOCG4_PAGE_SIZE; + mtd->erasesize = DOCG4_BLOCK_SIZE; + mtd->oobsize = DOCG4_OOB_SIZE; + nand->chipsize = DOCG4_CHIP_SIZE; + nand->chip_shift = DOCG4_CHIP_SHIFT; + nand->bbt_erase_shift = nand->phys_erase_shift = DOCG4_ERASE_SHIFT; + nand->chip_delay = 20; + nand->page_shift = DOCG4_PAGE_SHIFT; + nand->pagemask = 0x3ffff; + nand->badblockpos = NAND_LARGE_BADBLOCK_POS; + nand->badblockbits = 8; + nand->ecc.layout = &docg4_oobinfo; + nand->ecc.mode = NAND_ECC_HW_SYNDROME; + nand->ecc.size = DOCG4_PAGE_SIZE; + nand->ecc.prepad = 8; + nand->ecc.bytes = 8; + nand->ecc.strength = DOCG4_T; + nand->options = NAND_BUSWIDTH_16 | NAND_NO_SUBPAGE_WRITE; + nand->IO_ADDR_R = nand->IO_ADDR_W = doc->virtadr + DOC_IOSPACE_DATA; + nand->controller = &nand->hwcontrol; + spin_lock_init(&nand->controller->lock); + init_waitqueue_head(&nand->controller->wq); + + /* methods */ + nand->cmdfunc = docg4_command; + nand->waitfunc = docg4_wait; + nand->select_chip = docg4_select_chip; + nand->read_byte = docg4_read_byte; + nand->block_markbad = docg4_block_markbad; + nand->read_buf = docg4_read_buf; + nand->write_buf = docg4_write_buf16; + nand->erase = docg4_erase_block; + nand->ecc.read_page = docg4_read_page; + nand->ecc.write_page = docg4_write_page; + nand->ecc.read_page_raw = docg4_read_page_raw; + nand->ecc.write_page_raw = docg4_write_page_raw; + nand->ecc.read_oob = docg4_read_oob; + nand->ecc.write_oob = docg4_write_oob; + + /* + * The way the nand infrastructure code is written, a memory-based bbt + * is not created if NAND_SKIP_BBTSCAN is set. With no memory bbt, + * nand->block_bad() is used. So when ignoring bad blocks, we skip the + * scan and define a dummy block_bad() which always returns 0. + */ + if (ignore_badblocks) { + nand->options |= NAND_SKIP_BBTSCAN; + nand->block_bad = docg4_block_neverbad; + } + +} + +static int __init read_id_reg(struct mtd_info *mtd) +{ + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + void __iomem *docptr = doc->virtadr; + uint16_t id1, id2; + + /* check for presence of g4 chip by reading id registers */ + id1 = readw(docptr + DOC_CHIPID); + id1 = readw(docptr + DOCG4_MYSTERY_REG); + id2 = readw(docptr + DOC_CHIPID_INV); + id2 = readw(docptr + DOCG4_MYSTERY_REG); + + if (id1 == DOCG4_IDREG1_VALUE && id2 == DOCG4_IDREG2_VALUE) { + dev_info(doc->dev, + "NAND device: 128MiB Diskonchip G4 detected\n"); + return 0; + } + + return -ENODEV; +} + +static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL }; + +static int __init probe_docg4(struct platform_device *pdev) +{ + struct mtd_info *mtd; + struct nand_chip *nand; + void __iomem *virtadr; + struct docg4_priv *doc; + int len, retval; + struct resource *r; + struct device *dev = &pdev->dev; + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (r == NULL) { + dev_err(dev, "no io memory resource defined!\n"); + return -ENODEV; + } + + virtadr = ioremap(r->start, resource_size(r)); + if (!virtadr) { + dev_err(dev, "Diskonchip ioremap failed: %pR\n", r); + return -EIO; + } + + len = sizeof(struct mtd_info) + sizeof(struct nand_chip) + + sizeof(struct docg4_priv); + mtd = kzalloc(len, GFP_KERNEL); + if (mtd == NULL) { + retval = -ENOMEM; + goto fail; + } + nand = (struct nand_chip *) (mtd + 1); + doc = (struct docg4_priv *) (nand + 1); + mtd->priv = nand; + nand->priv = doc; + mtd->owner = THIS_MODULE; + doc->virtadr = virtadr; + doc->dev = dev; + + init_mtd_structs(mtd); + + /* initialize kernel bch algorithm */ + doc->bch = init_bch(DOCG4_M, DOCG4_T, DOCG4_PRIMITIVE_POLY); + if (doc->bch == NULL) { + retval = -EINVAL; + goto fail; + } + + platform_set_drvdata(pdev, doc); + + reset(mtd); + retval = read_id_reg(mtd); + if (retval == -ENODEV) { + dev_warn(dev, "No diskonchip G4 device found.\n"); + goto fail; + } + + retval = nand_scan_tail(mtd); + if (retval) + goto fail; + + retval = read_factory_bbt(mtd); + if (retval) + goto fail; + + retval = mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0); + if (retval) + goto fail; + + doc->mtd = mtd; + return 0; + + fail: + iounmap(virtadr); + if (mtd) { + /* re-declarations avoid compiler warning */ + struct nand_chip *nand = mtd->priv; + struct docg4_priv *doc = nand->priv; + nand_release(mtd); /* deletes partitions and mtd devices */ + free_bch(doc->bch); + kfree(mtd); + } + + return retval; +} + +static int __exit cleanup_docg4(struct platform_device *pdev) +{ + struct docg4_priv *doc = platform_get_drvdata(pdev); + nand_release(doc->mtd); + free_bch(doc->bch); + kfree(doc->mtd); + iounmap(doc->virtadr); + return 0; +} + +static struct platform_driver docg4_driver = { + .driver = { + .name = "docg4", + }, + .suspend = docg4_suspend, + .resume = docg4_resume, + .remove = __exit_p(cleanup_docg4), +}; + +module_platform_driver_probe(docg4_driver, probe_docg4); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Mike Dunn"); +MODULE_DESCRIPTION("M-Systems DiskOnChip G4 device driver"); diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c new file mode 100644 index 000000000..04b22fd37 --- /dev/null +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -0,0 +1,963 @@ +/* Freescale Enhanced Local Bus Controller NAND driver + * + * Copyright © 2006-2007, 2010 Freescale Semiconductor + * + * Authors: Nick Spence <nick.spence@freescale.com>, + * Scott Wood <scottwood@freescale.com> + * Jack Lan <jack.lan@freescale.com> + * Roy Zang <tie-fei.zang@freescale.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/interrupt.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <asm/io.h> +#include <asm/fsl_lbc.h> + +#define MAX_BANKS 8 +#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */ +#define FCM_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait for FCM */ + +/* mtd information per set */ + +struct fsl_elbc_mtd { + struct mtd_info mtd; + struct nand_chip chip; + struct fsl_lbc_ctrl *ctrl; + + struct device *dev; + int bank; /* Chip select bank number */ + u8 __iomem *vbase; /* Chip select base virtual address */ + int page_size; /* NAND page size (0=512, 1=2048) */ + unsigned int fmr; /* FCM Flash Mode Register value */ +}; + +/* Freescale eLBC FCM controller information */ + +struct fsl_elbc_fcm_ctrl { + struct nand_hw_control controller; + struct fsl_elbc_mtd *chips[MAX_BANKS]; + + u8 __iomem *addr; /* Address of assigned FCM buffer */ + unsigned int page; /* Last page written to / read from */ + unsigned int read_bytes; /* Number of bytes read during command */ + unsigned int column; /* Saved column from SEQIN */ + unsigned int index; /* Pointer to next byte to 'read' */ + unsigned int status; /* status read from LTESR after last op */ + unsigned int mdr; /* UPM/FCM Data Register value */ + unsigned int use_mdr; /* Non zero if the MDR is to be set */ + unsigned int oob; /* Non zero if operating on OOB data */ + unsigned int counter; /* counter for the initializations */ + unsigned int max_bitflips; /* Saved during READ0 cmd */ +}; + +/* These map to the positions used by the FCM hardware ECC generator */ + +/* Small Page FLASH with FMR[ECCM] = 0 */ +static struct nand_ecclayout fsl_elbc_oob_sp_eccm0 = { + .eccbytes = 3, + .eccpos = {6, 7, 8}, + .oobfree = { {0, 5}, {9, 7} }, +}; + +/* Small Page FLASH with FMR[ECCM] = 1 */ +static struct nand_ecclayout fsl_elbc_oob_sp_eccm1 = { + .eccbytes = 3, + .eccpos = {8, 9, 10}, + .oobfree = { {0, 5}, {6, 2}, {11, 5} }, +}; + +/* Large Page FLASH with FMR[ECCM] = 0 */ +static struct nand_ecclayout fsl_elbc_oob_lp_eccm0 = { + .eccbytes = 12, + .eccpos = {6, 7, 8, 22, 23, 24, 38, 39, 40, 54, 55, 56}, + .oobfree = { {1, 5}, {9, 13}, {25, 13}, {41, 13}, {57, 7} }, +}; + +/* Large Page FLASH with FMR[ECCM] = 1 */ +static struct nand_ecclayout fsl_elbc_oob_lp_eccm1 = { + .eccbytes = 12, + .eccpos = {8, 9, 10, 24, 25, 26, 40, 41, 42, 56, 57, 58}, + .oobfree = { {1, 7}, {11, 13}, {27, 13}, {43, 13}, {59, 5} }, +}; + +/* + * ELBC may use HW ECC, so that OOB offsets, that NAND core uses for bbt, + * interfere with ECC positions, that's why we implement our own descriptors. + * OOB {11, 5}, works for both SP and LP chips, with ECCM = 1 and ECCM = 0. + */ +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/*=================================*/ + +/* + * Set up the FCM hardware block and page address fields, and the fcm + * structure addr field to point to the correct FCM buffer in memory + */ +static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + int buf_num; + + elbc_fcm_ctrl->page = page_addr; + + if (priv->page_size) { + /* + * large page size chip : FPAR[PI] save the lowest 6 bits, + * FBAR[BLK] save the other bits. + */ + out_be32(&lbc->fbar, page_addr >> 6); + out_be32(&lbc->fpar, + ((page_addr << FPAR_LP_PI_SHIFT) & FPAR_LP_PI) | + (oob ? FPAR_LP_MS : 0) | column); + buf_num = (page_addr & 1) << 2; + } else { + /* + * small page size chip : FPAR[PI] save the lowest 5 bits, + * FBAR[BLK] save the other bits. + */ + out_be32(&lbc->fbar, page_addr >> 5); + out_be32(&lbc->fpar, + ((page_addr << FPAR_SP_PI_SHIFT) & FPAR_SP_PI) | + (oob ? FPAR_SP_MS : 0) | column); + buf_num = page_addr & 7; + } + + elbc_fcm_ctrl->addr = priv->vbase + buf_num * 1024; + elbc_fcm_ctrl->index = column; + + /* for OOB data point to the second half of the buffer */ + if (oob) + elbc_fcm_ctrl->index += priv->page_size ? 2048 : 512; + + dev_vdbg(priv->dev, "set_addr: bank=%d, " + "elbc_fcm_ctrl->addr=0x%p (0x%p), " + "index %x, pes %d ps %d\n", + buf_num, elbc_fcm_ctrl->addr, priv->vbase, + elbc_fcm_ctrl->index, + chip->phys_erase_shift, chip->page_shift); +} + +/* + * execute FCM command and wait for it to complete + */ +static int fsl_elbc_run_command(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + /* Setup the FMR[OP] to execute without write protection */ + out_be32(&lbc->fmr, priv->fmr | 3); + if (elbc_fcm_ctrl->use_mdr) + out_be32(&lbc->mdr, elbc_fcm_ctrl->mdr); + + dev_vdbg(priv->dev, + "fsl_elbc_run_command: fmr=%08x fir=%08x fcr=%08x\n", + in_be32(&lbc->fmr), in_be32(&lbc->fir), in_be32(&lbc->fcr)); + dev_vdbg(priv->dev, + "fsl_elbc_run_command: fbar=%08x fpar=%08x " + "fbcr=%08x bank=%d\n", + in_be32(&lbc->fbar), in_be32(&lbc->fpar), + in_be32(&lbc->fbcr), priv->bank); + + ctrl->irq_status = 0; + /* execute special operation */ + out_be32(&lbc->lsor, priv->bank); + + /* wait for FCM complete flag or timeout */ + wait_event_timeout(ctrl->irq_wait, ctrl->irq_status, + FCM_TIMEOUT_MSECS * HZ/1000); + elbc_fcm_ctrl->status = ctrl->irq_status; + /* store mdr value in case it was needed */ + if (elbc_fcm_ctrl->use_mdr) + elbc_fcm_ctrl->mdr = in_be32(&lbc->mdr); + + elbc_fcm_ctrl->use_mdr = 0; + + if (elbc_fcm_ctrl->status != LTESR_CC) { + dev_info(priv->dev, + "command failed: fir %x fcr %x status %x mdr %x\n", + in_be32(&lbc->fir), in_be32(&lbc->fcr), + elbc_fcm_ctrl->status, elbc_fcm_ctrl->mdr); + return -EIO; + } + + if (chip->ecc.mode != NAND_ECC_HW) + return 0; + + elbc_fcm_ctrl->max_bitflips = 0; + + if (elbc_fcm_ctrl->read_bytes == mtd->writesize + mtd->oobsize) { + uint32_t lteccr = in_be32(&lbc->lteccr); + /* + * if command was a full page read and the ELBC + * has the LTECCR register, then bits 12-15 (ppc order) of + * LTECCR indicates which 512 byte sub-pages had fixed errors. + * bits 28-31 are uncorrectable errors, marked elsewhere. + * for small page nand only 1 bit is used. + * if the ELBC doesn't have the lteccr register it reads 0 + * FIXME: 4 bits can be corrected on NANDs with 2k pages, so + * count the number of sub-pages with bitflips and update + * ecc_stats.corrected accordingly. + */ + if (lteccr & 0x000F000F) + out_be32(&lbc->lteccr, 0x000F000F); /* clear lteccr */ + if (lteccr & 0x000F0000) { + mtd->ecc_stats.corrected++; + elbc_fcm_ctrl->max_bitflips = 1; + } + } + + return 0; +} + +static void fsl_elbc_do_read(struct nand_chip *chip, int oob) +{ + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + if (priv->page_size) { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_CM1 << FIR_OP3_SHIFT) | + (FIR_OP_RBW << FIR_OP4_SHIFT)); + + out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) | + (NAND_CMD_READSTART << FCR_CMD1_SHIFT)); + } else { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_RBW << FIR_OP3_SHIFT)); + + if (oob) + out_be32(&lbc->fcr, NAND_CMD_READOOB << FCR_CMD0_SHIFT); + else + out_be32(&lbc->fcr, NAND_CMD_READ0 << FCR_CMD0_SHIFT); + } +} + +/* cmdfunc send commands to the FCM */ +static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + + elbc_fcm_ctrl->use_mdr = 0; + + /* clear the read buffer */ + elbc_fcm_ctrl->read_bytes = 0; + if (command != NAND_CMD_PAGEPROG) + elbc_fcm_ctrl->index = 0; + + switch (command) { + /* READ0 and READ1 read the entire buffer to use hardware ECC. */ + case NAND_CMD_READ1: + column += 256; + + /* fall-through */ + case NAND_CMD_READ0: + dev_dbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_READ0, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + + out_be32(&lbc->fbcr, 0); /* read entire page to enable ECC */ + set_addr(mtd, 0, page_addr, 0); + + elbc_fcm_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + elbc_fcm_ctrl->index += column; + + fsl_elbc_do_read(chip, 0); + fsl_elbc_run_command(mtd); + return; + + /* READOOB reads only the OOB because no ECC is performed. */ + case NAND_CMD_READOOB: + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_READOOB, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + out_be32(&lbc->fbcr, mtd->oobsize - column); + set_addr(mtd, column, page_addr, 1); + + elbc_fcm_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + + fsl_elbc_do_read(chip, 1); + fsl_elbc_run_command(mtd); + return; + + case NAND_CMD_READID: + case NAND_CMD_PARAM: + dev_vdbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD %x\n", command); + + out_be32(&lbc->fir, (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_UA << FIR_OP1_SHIFT) | + (FIR_OP_RBW << FIR_OP2_SHIFT)); + out_be32(&lbc->fcr, command << FCR_CMD0_SHIFT); + /* + * although currently it's 8 bytes for READID, we always read + * the maximum 256 bytes(for PARAM) + */ + out_be32(&lbc->fbcr, 256); + elbc_fcm_ctrl->read_bytes = 256; + elbc_fcm_ctrl->use_mdr = 1; + elbc_fcm_ctrl->mdr = column; + set_addr(mtd, 0, 0, 0); + fsl_elbc_run_command(mtd); + return; + + /* ERASE1 stores the block and page address */ + case NAND_CMD_ERASE1: + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_ERASE1, " + "page_addr: 0x%x.\n", page_addr); + set_addr(mtd, 0, page_addr, 0); + return; + + /* ERASE2 uses the block and page address from ERASE1 */ + case NAND_CMD_ERASE2: + dev_vdbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n"); + + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_PA << FIR_OP1_SHIFT) | + (FIR_OP_CM2 << FIR_OP2_SHIFT) | + (FIR_OP_CW1 << FIR_OP3_SHIFT) | + (FIR_OP_RS << FIR_OP4_SHIFT)); + + out_be32(&lbc->fcr, + (NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) | + (NAND_CMD_STATUS << FCR_CMD1_SHIFT) | + (NAND_CMD_ERASE2 << FCR_CMD2_SHIFT)); + + out_be32(&lbc->fbcr, 0); + elbc_fcm_ctrl->read_bytes = 0; + elbc_fcm_ctrl->use_mdr = 1; + + fsl_elbc_run_command(mtd); + return; + + /* SEQIN sets up the addr buffer and all registers except the length */ + case NAND_CMD_SEQIN: { + __be32 fcr; + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, " + "page_addr: 0x%x, column: 0x%x.\n", + page_addr, column); + + elbc_fcm_ctrl->column = column; + elbc_fcm_ctrl->use_mdr = 1; + + if (column >= mtd->writesize) { + /* OOB area */ + column -= mtd->writesize; + elbc_fcm_ctrl->oob = 1; + } else { + WARN_ON(column != 0); + elbc_fcm_ctrl->oob = 0; + } + + fcr = (NAND_CMD_STATUS << FCR_CMD1_SHIFT) | + (NAND_CMD_SEQIN << FCR_CMD2_SHIFT) | + (NAND_CMD_PAGEPROG << FCR_CMD3_SHIFT); + + if (priv->page_size) { + out_be32(&lbc->fir, + (FIR_OP_CM2 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_WB << FIR_OP3_SHIFT) | + (FIR_OP_CM3 << FIR_OP4_SHIFT) | + (FIR_OP_CW1 << FIR_OP5_SHIFT) | + (FIR_OP_RS << FIR_OP6_SHIFT)); + } else { + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_CM2 << FIR_OP1_SHIFT) | + (FIR_OP_CA << FIR_OP2_SHIFT) | + (FIR_OP_PA << FIR_OP3_SHIFT) | + (FIR_OP_WB << FIR_OP4_SHIFT) | + (FIR_OP_CM3 << FIR_OP5_SHIFT) | + (FIR_OP_CW1 << FIR_OP6_SHIFT) | + (FIR_OP_RS << FIR_OP7_SHIFT)); + + if (elbc_fcm_ctrl->oob) + /* OOB area --> READOOB */ + fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT; + else + /* First 256 bytes --> READ0 */ + fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT; + } + + out_be32(&lbc->fcr, fcr); + set_addr(mtd, column, page_addr, elbc_fcm_ctrl->oob); + return; + } + + /* PAGEPROG reuses all of the setup from SEQIN and adds the length */ + case NAND_CMD_PAGEPROG: { + dev_vdbg(priv->dev, + "fsl_elbc_cmdfunc: NAND_CMD_PAGEPROG " + "writing %d bytes.\n", elbc_fcm_ctrl->index); + + /* if the write did not start at 0 or is not a full page + * then set the exact length, otherwise use a full page + * write so the HW generates the ECC. + */ + if (elbc_fcm_ctrl->oob || elbc_fcm_ctrl->column != 0 || + elbc_fcm_ctrl->index != mtd->writesize + mtd->oobsize) + out_be32(&lbc->fbcr, + elbc_fcm_ctrl->index - elbc_fcm_ctrl->column); + else + out_be32(&lbc->fbcr, 0); + + fsl_elbc_run_command(mtd); + return; + } + + /* CMD_STATUS must read the status byte while CEB is active */ + /* Note - it does not wait for the ready line */ + case NAND_CMD_STATUS: + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_RBW << FIR_OP1_SHIFT)); + out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT); + out_be32(&lbc->fbcr, 1); + set_addr(mtd, 0, 0, 0); + elbc_fcm_ctrl->read_bytes = 1; + + fsl_elbc_run_command(mtd); + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + setbits8(elbc_fcm_ctrl->addr, NAND_STATUS_WP); + return; + + /* RESET without waiting for the ready line */ + case NAND_CMD_RESET: + dev_dbg(priv->dev, "fsl_elbc_cmdfunc: NAND_CMD_RESET.\n"); + out_be32(&lbc->fir, FIR_OP_CM0 << FIR_OP0_SHIFT); + out_be32(&lbc->fcr, NAND_CMD_RESET << FCR_CMD0_SHIFT); + fsl_elbc_run_command(mtd); + return; + + default: + dev_err(priv->dev, + "fsl_elbc_cmdfunc: error, unsupported command 0x%x.\n", + command); + } +} + +static void fsl_elbc_select_chip(struct mtd_info *mtd, int chip) +{ + /* The hardware does not seem to support multiple + * chips per bank. + */ +} + +/* + * Write buf to the FCM Controller Data Buffer + */ +static void fsl_elbc_write_buf(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + unsigned int bufsize = mtd->writesize + mtd->oobsize; + + if (len <= 0) { + dev_err(priv->dev, "write_buf of %d bytes", len); + elbc_fcm_ctrl->status = 0; + return; + } + + if ((unsigned int)len > bufsize - elbc_fcm_ctrl->index) { + dev_err(priv->dev, + "write_buf beyond end of buffer " + "(%d requested, %u available)\n", + len, bufsize - elbc_fcm_ctrl->index); + len = bufsize - elbc_fcm_ctrl->index; + } + + memcpy_toio(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index], buf, len); + /* + * This is workaround for the weird elbc hangs during nand write, + * Scott Wood says: "...perhaps difference in how long it takes a + * write to make it through the localbus compared to a write to IMMR + * is causing problems, and sync isn't helping for some reason." + * Reading back the last byte helps though. + */ + in_8(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index] + len - 1); + + elbc_fcm_ctrl->index += len; +} + +/* + * read a byte from either the FCM hardware buffer if it has any data left + * otherwise issue a command to read a single byte. + */ +static u8 fsl_elbc_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + + /* If there are still bytes in the FCM, then use the next byte. */ + if (elbc_fcm_ctrl->index < elbc_fcm_ctrl->read_bytes) + return in_8(&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index++]); + + dev_err(priv->dev, "read_byte beyond end of buffer\n"); + return ERR_BYTE; +} + +/* + * Read from the FCM Controller Data Buffer + */ +static void fsl_elbc_read_buf(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + int avail; + + if (len < 0) + return; + + avail = min((unsigned int)len, + elbc_fcm_ctrl->read_bytes - elbc_fcm_ctrl->index); + memcpy_fromio(buf, &elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index], avail); + elbc_fcm_ctrl->index += avail; + + if (len > avail) + dev_err(priv->dev, + "read_buf beyond end of buffer " + "(%d requested, %d available)\n", + len, avail); +} + +/* This function is called after Program and Erase Operations to + * check for success or failure. + */ +static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + + if (elbc_fcm_ctrl->status != LTESR_CC) + return NAND_STATUS_FAIL; + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + return (elbc_fcm_ctrl->mdr & 0xff) | NAND_STATUS_WP; +} + +static int fsl_elbc_chip_init_tail(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + unsigned int al; + + /* calculate FMR Address Length field */ + al = 0; + if (chip->pagemask & 0xffff0000) + al++; + if (chip->pagemask & 0xff000000) + al++; + + priv->fmr |= al << FMR_AL_SHIFT; + + dev_dbg(priv->dev, "fsl_elbc_init: nand->numchips = %d\n", + chip->numchips); + dev_dbg(priv->dev, "fsl_elbc_init: nand->chipsize = %lld\n", + chip->chipsize); + dev_dbg(priv->dev, "fsl_elbc_init: nand->pagemask = %8x\n", + chip->pagemask); + dev_dbg(priv->dev, "fsl_elbc_init: nand->chip_delay = %d\n", + chip->chip_delay); + dev_dbg(priv->dev, "fsl_elbc_init: nand->badblockpos = %d\n", + chip->badblockpos); + dev_dbg(priv->dev, "fsl_elbc_init: nand->chip_shift = %d\n", + chip->chip_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->page_shift = %d\n", + chip->page_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->phys_erase_shift = %d\n", + chip->phys_erase_shift); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.mode = %d\n", + chip->ecc.mode); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.steps = %d\n", + chip->ecc.steps); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.bytes = %d\n", + chip->ecc.bytes); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.total = %d\n", + chip->ecc.total); + dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.layout = %p\n", + chip->ecc.layout); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->flags = %08x\n", mtd->flags); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->size = %lld\n", mtd->size); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->erasesize = %d\n", + mtd->erasesize); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->writesize = %d\n", + mtd->writesize); + dev_dbg(priv->dev, "fsl_elbc_init: mtd->oobsize = %d\n", + mtd->oobsize); + + /* adjust Option Register and ECC to match Flash page size */ + if (mtd->writesize == 512) { + priv->page_size = 0; + clrbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS); + } else if (mtd->writesize == 2048) { + priv->page_size = 1; + setbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS); + /* adjust ecc setup if needed */ + if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) == + BR_DECC_CHK_GEN) { + chip->ecc.size = 512; + chip->ecc.layout = (priv->fmr & FMR_ECCM) ? + &fsl_elbc_oob_lp_eccm1 : + &fsl_elbc_oob_lp_eccm0; + } + } else { + dev_err(priv->dev, + "fsl_elbc_init: page size %d is not supported\n", + mtd->writesize); + return -1; + } + + return 0; +} + +static int fsl_elbc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct fsl_elbc_mtd *priv = chip->priv; + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + + fsl_elbc_read_buf(mtd, buf, mtd->writesize); + if (oob_required) + fsl_elbc_read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (fsl_elbc_wait(mtd, chip) & NAND_STATUS_FAIL) + mtd->ecc_stats.failed++; + + return elbc_fcm_ctrl->max_bitflips; +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + fsl_elbc_write_buf(mtd, buf, mtd->writesize); + fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_subpage(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, uint32_t data_len, + const uint8_t *buf, int oob_required) +{ + fsl_elbc_write_buf(mtd, buf, mtd->writesize); + fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv) +{ + struct fsl_lbc_ctrl *ctrl = priv->ctrl; + struct fsl_lbc_regs __iomem *lbc = ctrl->regs; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; + struct nand_chip *chip = &priv->chip; + + dev_dbg(priv->dev, "eLBC Set Information for bank %d\n", priv->bank); + + /* Fill in fsl_elbc_mtd structure */ + priv->mtd.priv = chip; + priv->mtd.owner = THIS_MODULE; + + /* set timeout to maximum */ + priv->fmr = 15 << FMR_CWTO_SHIFT; + if (in_be32(&lbc->bank[priv->bank].or) & OR_FCM_PGS) + priv->fmr |= FMR_ECCM; + + /* fill in nand_chip structure */ + /* set up function call table */ + chip->read_byte = fsl_elbc_read_byte; + chip->write_buf = fsl_elbc_write_buf; + chip->read_buf = fsl_elbc_read_buf; + chip->select_chip = fsl_elbc_select_chip; + chip->cmdfunc = fsl_elbc_cmdfunc; + chip->waitfunc = fsl_elbc_wait; + + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + + /* set up nand options */ + chip->bbt_options = NAND_BBT_USE_FLASH; + + chip->controller = &elbc_fcm_ctrl->controller; + chip->priv = priv; + + chip->ecc.read_page = fsl_elbc_read_page; + chip->ecc.write_page = fsl_elbc_write_page; + chip->ecc.write_subpage = fsl_elbc_write_subpage; + + /* If CS Base Register selects full hardware ECC then use it */ + if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) == + BR_DECC_CHK_GEN) { + chip->ecc.mode = NAND_ECC_HW; + /* put in small page settings and adjust later if needed */ + chip->ecc.layout = (priv->fmr & FMR_ECCM) ? + &fsl_elbc_oob_sp_eccm1 : &fsl_elbc_oob_sp_eccm0; + chip->ecc.size = 512; + chip->ecc.bytes = 3; + chip->ecc.strength = 1; + } else { + /* otherwise fall back to default software ECC */ + chip->ecc.mode = NAND_ECC_SOFT; + } + + return 0; +} + +static int fsl_elbc_chip_remove(struct fsl_elbc_mtd *priv) +{ + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand; + nand_release(&priv->mtd); + + kfree(priv->mtd.name); + + if (priv->vbase) + iounmap(priv->vbase); + + elbc_fcm_ctrl->chips[priv->bank] = NULL; + kfree(priv); + return 0; +} + +static DEFINE_MUTEX(fsl_elbc_nand_mutex); + +static int fsl_elbc_nand_probe(struct platform_device *pdev) +{ + struct fsl_lbc_regs __iomem *lbc; + struct fsl_elbc_mtd *priv; + struct resource res; + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl; + static const char *part_probe_types[] + = { "cmdlinepart", "RedBoot", "ofpart", NULL }; + int ret; + int bank; + struct device *dev; + struct device_node *node = pdev->dev.of_node; + struct mtd_part_parser_data ppdata; + + ppdata.of_node = pdev->dev.of_node; + if (!fsl_lbc_ctrl_dev || !fsl_lbc_ctrl_dev->regs) + return -ENODEV; + lbc = fsl_lbc_ctrl_dev->regs; + dev = fsl_lbc_ctrl_dev->dev; + + /* get, allocate and map the memory resource */ + ret = of_address_to_resource(node, 0, &res); + if (ret) { + dev_err(dev, "failed to get resource\n"); + return ret; + } + + /* find which chip select it is connected to */ + for (bank = 0; bank < MAX_BANKS; bank++) + if ((in_be32(&lbc->bank[bank].br) & BR_V) && + (in_be32(&lbc->bank[bank].br) & BR_MSEL) == BR_MS_FCM && + (in_be32(&lbc->bank[bank].br) & + in_be32(&lbc->bank[bank].or) & BR_BA) + == fsl_lbc_addr(res.start)) + break; + + if (bank >= MAX_BANKS) { + dev_err(dev, "address did not match any chip selects\n"); + return -ENODEV; + } + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + mutex_lock(&fsl_elbc_nand_mutex); + if (!fsl_lbc_ctrl_dev->nand) { + elbc_fcm_ctrl = kzalloc(sizeof(*elbc_fcm_ctrl), GFP_KERNEL); + if (!elbc_fcm_ctrl) { + mutex_unlock(&fsl_elbc_nand_mutex); + ret = -ENOMEM; + goto err; + } + elbc_fcm_ctrl->counter++; + + spin_lock_init(&elbc_fcm_ctrl->controller.lock); + init_waitqueue_head(&elbc_fcm_ctrl->controller.wq); + fsl_lbc_ctrl_dev->nand = elbc_fcm_ctrl; + } else { + elbc_fcm_ctrl = fsl_lbc_ctrl_dev->nand; + } + mutex_unlock(&fsl_elbc_nand_mutex); + + elbc_fcm_ctrl->chips[bank] = priv; + priv->bank = bank; + priv->ctrl = fsl_lbc_ctrl_dev; + priv->dev = &pdev->dev; + dev_set_drvdata(priv->dev, priv); + + priv->vbase = ioremap(res.start, resource_size(&res)); + if (!priv->vbase) { + dev_err(dev, "failed to map chip region\n"); + ret = -ENOMEM; + goto err; + } + + priv->mtd.name = kasprintf(GFP_KERNEL, "%llx.flash", (u64)res.start); + if (!priv->mtd.name) { + ret = -ENOMEM; + goto err; + } + + ret = fsl_elbc_chip_init(priv); + if (ret) + goto err; + + ret = nand_scan_ident(&priv->mtd, 1, NULL); + if (ret) + goto err; + + ret = fsl_elbc_chip_init_tail(&priv->mtd); + if (ret) + goto err; + + ret = nand_scan_tail(&priv->mtd); + if (ret) + goto err; + + /* First look for RedBoot table or partitions on the command + * line, these take precedence over device tree information */ + mtd_device_parse_register(&priv->mtd, part_probe_types, &ppdata, + NULL, 0); + + printk(KERN_INFO "eLBC NAND device at 0x%llx, bank %d\n", + (unsigned long long)res.start, priv->bank); + return 0; + +err: + fsl_elbc_chip_remove(priv); + return ret; +} + +static int fsl_elbc_nand_remove(struct platform_device *pdev) +{ + struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = fsl_lbc_ctrl_dev->nand; + struct fsl_elbc_mtd *priv = dev_get_drvdata(&pdev->dev); + + fsl_elbc_chip_remove(priv); + + mutex_lock(&fsl_elbc_nand_mutex); + elbc_fcm_ctrl->counter--; + if (!elbc_fcm_ctrl->counter) { + fsl_lbc_ctrl_dev->nand = NULL; + kfree(elbc_fcm_ctrl); + } + mutex_unlock(&fsl_elbc_nand_mutex); + + return 0; + +} + +static const struct of_device_id fsl_elbc_nand_match[] = { + { .compatible = "fsl,elbc-fcm-nand", }, + {} +}; + +static struct platform_driver fsl_elbc_nand_driver = { + .driver = { + .name = "fsl,elbc-fcm-nand", + .of_match_table = fsl_elbc_nand_match, + }, + .probe = fsl_elbc_nand_probe, + .remove = fsl_elbc_nand_remove, +}; + +module_platform_driver(fsl_elbc_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Freescale"); +MODULE_DESCRIPTION("Freescale Enhanced Local Bus Controller MTD NAND driver"); diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c new file mode 100644 index 000000000..51394e599 --- /dev/null +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -0,0 +1,1178 @@ +/* + * Freescale Integrated Flash Controller NAND driver + * + * Copyright 2011-2012 Freescale Semiconductor, Inc + * + * Author: Dipen Dudhat <Dipen.Dudhat@freescale.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/of_address.h> +#include <linux/slab.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/fsl_ifc.h> + +#define ERR_BYTE 0xFF /* Value returned for read + bytes when read failed */ +#define IFC_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait + for IFC NAND Machine */ + +struct fsl_ifc_ctrl; + +/* mtd information per set */ +struct fsl_ifc_mtd { + struct mtd_info mtd; + struct nand_chip chip; + struct fsl_ifc_ctrl *ctrl; + + struct device *dev; + int bank; /* Chip select bank number */ + unsigned int bufnum_mask; /* bufnum = page & bufnum_mask */ + u8 __iomem *vbase; /* Chip select base virtual address */ +}; + +/* overview of the fsl ifc controller */ +struct fsl_ifc_nand_ctrl { + struct nand_hw_control controller; + struct fsl_ifc_mtd *chips[FSL_IFC_BANK_COUNT]; + + void __iomem *addr; /* Address of assigned IFC buffer */ + unsigned int page; /* Last page written to / read from */ + unsigned int read_bytes;/* Number of bytes read during command */ + unsigned int column; /* Saved column from SEQIN */ + unsigned int index; /* Pointer to next byte to 'read' */ + unsigned int oob; /* Non zero if operating on OOB data */ + unsigned int eccread; /* Non zero for a full-page ECC read */ + unsigned int counter; /* counter for the initializations */ + unsigned int max_bitflips; /* Saved during READ0 cmd */ +}; + +static struct fsl_ifc_nand_ctrl *ifc_nand_ctrl; + +/* 512-byte page with 4-bit ECC, 8-bit */ +static struct nand_ecclayout oob_512_8bit_ecc4 = { + .eccbytes = 8, + .eccpos = {8, 9, 10, 11, 12, 13, 14, 15}, + .oobfree = { {0, 5}, {6, 2} }, +}; + +/* 512-byte page with 4-bit ECC, 16-bit */ +static struct nand_ecclayout oob_512_16bit_ecc4 = { + .eccbytes = 8, + .eccpos = {8, 9, 10, 11, 12, 13, 14, 15}, + .oobfree = { {2, 6}, }, +}; + +/* 2048-byte page size with 4-bit ECC */ +static struct nand_ecclayout oob_2048_ecc4 = { + .eccbytes = 32, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + }, + .oobfree = { {2, 6}, {40, 24} }, +}; + +/* 4096-byte page size with 4-bit ECC */ +static struct nand_ecclayout oob_4096_ecc4 = { + .eccbytes = 64, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + }, + .oobfree = { {2, 6}, {72, 56} }, +}; + +/* 4096-byte page size with 8-bit ECC -- requires 218-byte OOB */ +static struct nand_ecclayout oob_4096_ecc8 = { + .eccbytes = 128, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + }, + .oobfree = { {2, 6}, {136, 82} }, +}; + +/* 8192-byte page size with 4-bit ECC */ +static struct nand_ecclayout oob_8192_ecc4 = { + .eccbytes = 128, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + }, + .oobfree = { {2, 6}, {136, 208} }, +}; + +/* 8192-byte page size with 8-bit ECC -- requires 218-byte OOB */ +static struct nand_ecclayout oob_8192_ecc8 = { + .eccbytes = 256, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + 136, 137, 138, 139, 140, 141, 142, 143, + 144, 145, 146, 147, 148, 149, 150, 151, + 152, 153, 154, 155, 156, 157, 158, 159, + 160, 161, 162, 163, 164, 165, 166, 167, + 168, 169, 170, 171, 172, 173, 174, 175, + 176, 177, 178, 179, 180, 181, 182, 183, + 184, 185, 186, 187, 188, 189, 190, 191, + 192, 193, 194, 195, 196, 197, 198, 199, + 200, 201, 202, 203, 204, 205, 206, 207, + 208, 209, 210, 211, 212, 213, 214, 215, + 216, 217, 218, 219, 220, 221, 222, 223, + 224, 225, 226, 227, 228, 229, 230, 231, + 232, 233, 234, 235, 236, 237, 238, 239, + 240, 241, 242, 243, 244, 245, 246, 247, + 248, 249, 250, 251, 252, 253, 254, 255, + 256, 257, 258, 259, 260, 261, 262, 263, + }, + .oobfree = { {2, 6}, {264, 80} }, +}; + +/* + * Generic flash bbt descriptors + */ +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 2, /* 0 on 8-bit small page */ + .len = 4, + .veroffs = 6, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 2, /* 0 on 8-bit small page */ + .len = 4, + .veroffs = 6, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/* + * Set up the IFC hardware block and page address fields, and the ifc nand + * structure addr field to point to the correct IFC buffer in memory + */ +static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + int buf_num; + + ifc_nand_ctrl->page = page_addr; + /* Program ROW0/COL0 */ + iowrite32be(page_addr, &ifc->ifc_nand.row0); + iowrite32be((oob ? IFC_NAND_COL_MS : 0) | column, &ifc->ifc_nand.col0); + + buf_num = page_addr & priv->bufnum_mask; + + ifc_nand_ctrl->addr = priv->vbase + buf_num * (mtd->writesize * 2); + ifc_nand_ctrl->index = column; + + /* for OOB data point to the second half of the buffer */ + if (oob) + ifc_nand_ctrl->index += mtd->writesize; +} + +static int is_blank(struct mtd_info *mtd, unsigned int bufnum) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + u8 __iomem *addr = priv->vbase + bufnum * (mtd->writesize * 2); + u32 __iomem *mainarea = (u32 __iomem *)addr; + u8 __iomem *oob = addr + mtd->writesize; + int i; + + for (i = 0; i < mtd->writesize / 4; i++) { + if (__raw_readl(&mainarea[i]) != 0xffffffff) + return 0; + } + + for (i = 0; i < chip->ecc.layout->eccbytes; i++) { + int pos = chip->ecc.layout->eccpos[i]; + + if (__raw_readb(&oob[pos]) != 0xff) + return 0; + } + + return 1; +} + +/* returns nonzero if entire page is blank */ +static int check_read_ecc(struct mtd_info *mtd, struct fsl_ifc_ctrl *ctrl, + u32 *eccstat, unsigned int bufnum) +{ + u32 reg = eccstat[bufnum / 4]; + int errors; + + errors = (reg >> ((3 - bufnum % 4) * 8)) & 15; + + return errors; +} + +/* + * execute IFC NAND command and wait for it to complete + */ +static void fsl_ifc_run_command(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_nand_ctrl *nctrl = ifc_nand_ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + u32 eccstat[4]; + int i; + + /* set the chip select for NAND Transaction */ + iowrite32be(priv->bank << IFC_NAND_CSEL_SHIFT, + &ifc->ifc_nand.nand_csel); + + dev_vdbg(priv->dev, + "%s: fir0=%08x fcr0=%08x\n", + __func__, + ioread32be(&ifc->ifc_nand.nand_fir0), + ioread32be(&ifc->ifc_nand.nand_fcr0)); + + ctrl->nand_stat = 0; + + /* start read/write seq */ + iowrite32be(IFC_NAND_SEQ_STRT_FIR_STRT, &ifc->ifc_nand.nandseq_strt); + + /* wait for command complete flag or timeout */ + wait_event_timeout(ctrl->nand_wait, ctrl->nand_stat, + msecs_to_jiffies(IFC_TIMEOUT_MSECS)); + + /* ctrl->nand_stat will be updated from IRQ context */ + if (!ctrl->nand_stat) + dev_err(priv->dev, "Controller is not responding\n"); + if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_FTOER) + dev_err(priv->dev, "NAND Flash Timeout Error\n"); + if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_WPER) + dev_err(priv->dev, "NAND Flash Write Protect Error\n"); + + nctrl->max_bitflips = 0; + + if (nctrl->eccread) { + int errors; + int bufnum = nctrl->page & priv->bufnum_mask; + int sector = bufnum * chip->ecc.steps; + int sector_end = sector + chip->ecc.steps - 1; + + for (i = sector / 4; i <= sector_end / 4; i++) + eccstat[i] = ioread32be(&ifc->ifc_nand.nand_eccstat[i]); + + for (i = sector; i <= sector_end; i++) { + errors = check_read_ecc(mtd, ctrl, eccstat, i); + + if (errors == 15) { + /* + * Uncorrectable error. + * OK only if the whole page is blank. + * + * We disable ECCER reporting due to... + * erratum IFC-A002770 -- so report it now if we + * see an uncorrectable error in ECCSTAT. + */ + if (!is_blank(mtd, bufnum)) + ctrl->nand_stat |= + IFC_NAND_EVTER_STAT_ECCER; + break; + } + + mtd->ecc_stats.corrected += errors; + nctrl->max_bitflips = max_t(unsigned int, + nctrl->max_bitflips, + errors); + } + + nctrl->eccread = 0; + } +} + +static void fsl_ifc_do_read(struct nand_chip *chip, + int oob, + struct mtd_info *mtd) +{ + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + + /* Program FIR/IFC_NAND_FCR0 for Small/Large page */ + if (mtd->writesize > 512) { + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | + (IFC_FIR_OP_CMD1 << IFC_NAND_FIR0_OP3_SHIFT) | + (IFC_FIR_OP_RBCD << IFC_NAND_FIR0_OP4_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(0x0, &ifc->ifc_nand.nand_fir1); + + iowrite32be((NAND_CMD_READ0 << IFC_NAND_FCR0_CMD0_SHIFT) | + (NAND_CMD_READSTART << IFC_NAND_FCR0_CMD1_SHIFT), + &ifc->ifc_nand.nand_fcr0); + } else { + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | + (IFC_FIR_OP_RBCD << IFC_NAND_FIR0_OP3_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(0x0, &ifc->ifc_nand.nand_fir1); + + if (oob) + iowrite32be(NAND_CMD_READOOB << + IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + else + iowrite32be(NAND_CMD_READ0 << + IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + } +} + +/* cmdfunc send commands to the IFC NAND Machine */ +static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) { + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + + /* clear the read buffer */ + ifc_nand_ctrl->read_bytes = 0; + if (command != NAND_CMD_PAGEPROG) + ifc_nand_ctrl->index = 0; + + switch (command) { + /* READ0 read the entire buffer to use hardware ECC. */ + case NAND_CMD_READ0: + iowrite32be(0, &ifc->ifc_nand.nand_fbcr); + set_addr(mtd, 0, page_addr, 0); + + ifc_nand_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + ifc_nand_ctrl->index += column; + + if (chip->ecc.mode == NAND_ECC_HW) + ifc_nand_ctrl->eccread = 1; + + fsl_ifc_do_read(chip, 0, mtd); + fsl_ifc_run_command(mtd); + return; + + /* READOOB reads only the OOB because no ECC is performed. */ + case NAND_CMD_READOOB: + iowrite32be(mtd->oobsize - column, &ifc->ifc_nand.nand_fbcr); + set_addr(mtd, column, page_addr, 1); + + ifc_nand_ctrl->read_bytes = mtd->writesize + mtd->oobsize; + + fsl_ifc_do_read(chip, 1, mtd); + fsl_ifc_run_command(mtd); + + return; + + case NAND_CMD_READID: + case NAND_CMD_PARAM: { + int timing = IFC_FIR_OP_RB; + if (command == NAND_CMD_PARAM) + timing = IFC_FIR_OP_RBCD; + + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) | + (timing << IFC_NAND_FIR0_OP2_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(command << IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + iowrite32be(column, &ifc->ifc_nand.row3); + + /* + * although currently it's 8 bytes for READID, we always read + * the maximum 256 bytes(for PARAM) + */ + iowrite32be(256, &ifc->ifc_nand.nand_fbcr); + ifc_nand_ctrl->read_bytes = 256; + + set_addr(mtd, 0, 0, 0); + fsl_ifc_run_command(mtd); + return; + } + + /* ERASE1 stores the block and page address */ + case NAND_CMD_ERASE1: + set_addr(mtd, 0, page_addr, 0); + return; + + /* ERASE2 uses the block and page address from ERASE1 */ + case NAND_CMD_ERASE2: + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_CMD1 << IFC_NAND_FIR0_OP2_SHIFT), + &ifc->ifc_nand.nand_fir0); + + iowrite32be((NAND_CMD_ERASE1 << IFC_NAND_FCR0_CMD0_SHIFT) | + (NAND_CMD_ERASE2 << IFC_NAND_FCR0_CMD1_SHIFT), + &ifc->ifc_nand.nand_fcr0); + + iowrite32be(0, &ifc->ifc_nand.nand_fbcr); + ifc_nand_ctrl->read_bytes = 0; + fsl_ifc_run_command(mtd); + return; + + /* SEQIN sets up the addr buffer and all registers except the length */ + case NAND_CMD_SEQIN: { + u32 nand_fcr0; + ifc_nand_ctrl->column = column; + ifc_nand_ctrl->oob = 0; + + if (mtd->writesize > 512) { + nand_fcr0 = + (NAND_CMD_SEQIN << IFC_NAND_FCR0_CMD0_SHIFT) | + (NAND_CMD_STATUS << IFC_NAND_FCR0_CMD1_SHIFT) | + (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD2_SHIFT); + + iowrite32be( + (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | + (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP3_SHIFT) | + (IFC_FIR_OP_CMD2 << IFC_NAND_FIR0_OP4_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be( + (IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP7_SHIFT), + &ifc->ifc_nand.nand_fir1); + } else { + nand_fcr0 = ((NAND_CMD_PAGEPROG << + IFC_NAND_FCR0_CMD1_SHIFT) | + (NAND_CMD_SEQIN << + IFC_NAND_FCR0_CMD2_SHIFT) | + (NAND_CMD_STATUS << + IFC_NAND_FCR0_CMD3_SHIFT)); + + iowrite32be( + (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_CMD2 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP2_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP3_SHIFT) | + (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP4_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be( + (IFC_FIR_OP_CMD1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_CW3 << IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP7_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP8_SHIFT), + &ifc->ifc_nand.nand_fir1); + + if (column >= mtd->writesize) + nand_fcr0 |= + NAND_CMD_READOOB << IFC_NAND_FCR0_CMD0_SHIFT; + else + nand_fcr0 |= + NAND_CMD_READ0 << IFC_NAND_FCR0_CMD0_SHIFT; + } + + if (column >= mtd->writesize) { + /* OOB area --> READOOB */ + column -= mtd->writesize; + ifc_nand_ctrl->oob = 1; + } + iowrite32be(nand_fcr0, &ifc->ifc_nand.nand_fcr0); + set_addr(mtd, column, page_addr, ifc_nand_ctrl->oob); + return; + } + + /* PAGEPROG reuses all of the setup from SEQIN and adds the length */ + case NAND_CMD_PAGEPROG: { + if (ifc_nand_ctrl->oob) { + iowrite32be(ifc_nand_ctrl->index - + ifc_nand_ctrl->column, + &ifc->ifc_nand.nand_fbcr); + } else { + iowrite32be(0, &ifc->ifc_nand.nand_fbcr); + } + + fsl_ifc_run_command(mtd); + return; + } + + case NAND_CMD_STATUS: + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_RB << IFC_NAND_FIR0_OP1_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(NAND_CMD_STATUS << IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + iowrite32be(1, &ifc->ifc_nand.nand_fbcr); + set_addr(mtd, 0, 0, 0); + ifc_nand_ctrl->read_bytes = 1; + + fsl_ifc_run_command(mtd); + + /* + * The chip always seems to report that it is + * write-protected, even when it is not. + */ + if (chip->options & NAND_BUSWIDTH_16) + setbits16(ifc_nand_ctrl->addr, NAND_STATUS_WP); + else + setbits8(ifc_nand_ctrl->addr, NAND_STATUS_WP); + return; + + case NAND_CMD_RESET: + iowrite32be(IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT, + &ifc->ifc_nand.nand_fir0); + iowrite32be(NAND_CMD_RESET << IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + fsl_ifc_run_command(mtd); + return; + + default: + dev_err(priv->dev, "%s: error, unsupported command 0x%x.\n", + __func__, command); + } +} + +static void fsl_ifc_select_chip(struct mtd_info *mtd, int chip) +{ + /* The hardware does not seem to support multiple + * chips per bank. + */ +} + +/* + * Write buf to the IFC NAND Controller Data Buffer + */ +static void fsl_ifc_write_buf(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + unsigned int bufsize = mtd->writesize + mtd->oobsize; + + if (len <= 0) { + dev_err(priv->dev, "%s: len %d bytes", __func__, len); + return; + } + + if ((unsigned int)len > bufsize - ifc_nand_ctrl->index) { + dev_err(priv->dev, + "%s: beyond end of buffer (%d requested, %u available)\n", + __func__, len, bufsize - ifc_nand_ctrl->index); + len = bufsize - ifc_nand_ctrl->index; + } + + memcpy_toio(ifc_nand_ctrl->addr + ifc_nand_ctrl->index, buf, len); + ifc_nand_ctrl->index += len; +} + +/* + * Read a byte from either the IFC hardware buffer + * read function for 8-bit buswidth + */ +static uint8_t fsl_ifc_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + unsigned int offset; + + /* + * If there are still bytes in the IFC buffer, then use the + * next byte. + */ + if (ifc_nand_ctrl->index < ifc_nand_ctrl->read_bytes) { + offset = ifc_nand_ctrl->index++; + return in_8(ifc_nand_ctrl->addr + offset); + } + + dev_err(priv->dev, "%s: beyond end of buffer\n", __func__); + return ERR_BYTE; +} + +/* + * Read two bytes from the IFC hardware buffer + * read function for 16-bit buswith + */ +static uint8_t fsl_ifc_read_byte16(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + uint16_t data; + + /* + * If there are still bytes in the IFC buffer, then use the + * next byte. + */ + if (ifc_nand_ctrl->index < ifc_nand_ctrl->read_bytes) { + data = in_be16(ifc_nand_ctrl->addr + ifc_nand_ctrl->index); + ifc_nand_ctrl->index += 2; + return (uint8_t) data; + } + + dev_err(priv->dev, "%s: beyond end of buffer\n", __func__); + return ERR_BYTE; +} + +/* + * Read from the IFC Controller Data Buffer + */ +static void fsl_ifc_read_buf(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + int avail; + + if (len < 0) { + dev_err(priv->dev, "%s: len %d bytes", __func__, len); + return; + } + + avail = min((unsigned int)len, + ifc_nand_ctrl->read_bytes - ifc_nand_ctrl->index); + memcpy_fromio(buf, ifc_nand_ctrl->addr + ifc_nand_ctrl->index, avail); + ifc_nand_ctrl->index += avail; + + if (len > avail) + dev_err(priv->dev, + "%s: beyond end of buffer (%d requested, %d available)\n", + __func__, len, avail); +} + +/* + * This function is called after Program and Erase Operations to + * check for success or failure. + */ +static int fsl_ifc_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + u32 nand_fsr; + + /* Use READ_STATUS command, but wait for the device to be ready */ + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_RDSTAT << IFC_NAND_FIR0_OP1_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(NAND_CMD_STATUS << IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + iowrite32be(1, &ifc->ifc_nand.nand_fbcr); + set_addr(mtd, 0, 0, 0); + ifc_nand_ctrl->read_bytes = 1; + + fsl_ifc_run_command(mtd); + + nand_fsr = ioread32be(&ifc->ifc_nand.nand_fsr); + + /* + * The chip always seems to report that it is + * write-protected, even when it is not. + */ + return nand_fsr | NAND_STATUS_WP; +} + +static int fsl_ifc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct fsl_ifc_mtd *priv = chip->priv; + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_nand_ctrl *nctrl = ifc_nand_ctrl; + + fsl_ifc_read_buf(mtd, buf, mtd->writesize); + if (oob_required) + fsl_ifc_read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_ECCER) + dev_err(priv->dev, "NAND Flash ECC Uncorrectable Error\n"); + + if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC) + mtd->ecc_stats.failed++; + + return nctrl->max_bitflips; +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_ifc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + fsl_ifc_write_buf(mtd, buf, mtd->writesize); + fsl_ifc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static int fsl_ifc_chip_init_tail(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_ifc_mtd *priv = chip->priv; + + dev_dbg(priv->dev, "%s: nand->numchips = %d\n", __func__, + chip->numchips); + dev_dbg(priv->dev, "%s: nand->chipsize = %lld\n", __func__, + chip->chipsize); + dev_dbg(priv->dev, "%s: nand->pagemask = %8x\n", __func__, + chip->pagemask); + dev_dbg(priv->dev, "%s: nand->chip_delay = %d\n", __func__, + chip->chip_delay); + dev_dbg(priv->dev, "%s: nand->badblockpos = %d\n", __func__, + chip->badblockpos); + dev_dbg(priv->dev, "%s: nand->chip_shift = %d\n", __func__, + chip->chip_shift); + dev_dbg(priv->dev, "%s: nand->page_shift = %d\n", __func__, + chip->page_shift); + dev_dbg(priv->dev, "%s: nand->phys_erase_shift = %d\n", __func__, + chip->phys_erase_shift); + dev_dbg(priv->dev, "%s: nand->ecc.mode = %d\n", __func__, + chip->ecc.mode); + dev_dbg(priv->dev, "%s: nand->ecc.steps = %d\n", __func__, + chip->ecc.steps); + dev_dbg(priv->dev, "%s: nand->ecc.bytes = %d\n", __func__, + chip->ecc.bytes); + dev_dbg(priv->dev, "%s: nand->ecc.total = %d\n", __func__, + chip->ecc.total); + dev_dbg(priv->dev, "%s: nand->ecc.layout = %p\n", __func__, + chip->ecc.layout); + dev_dbg(priv->dev, "%s: mtd->flags = %08x\n", __func__, mtd->flags); + dev_dbg(priv->dev, "%s: mtd->size = %lld\n", __func__, mtd->size); + dev_dbg(priv->dev, "%s: mtd->erasesize = %d\n", __func__, + mtd->erasesize); + dev_dbg(priv->dev, "%s: mtd->writesize = %d\n", __func__, + mtd->writesize); + dev_dbg(priv->dev, "%s: mtd->oobsize = %d\n", __func__, + mtd->oobsize); + + return 0; +} + +static void fsl_ifc_sram_init(struct fsl_ifc_mtd *priv) +{ + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + uint32_t csor = 0, csor_8k = 0, csor_ext = 0; + uint32_t cs = priv->bank; + + /* Save CSOR and CSOR_ext */ + csor = ioread32be(&ifc->csor_cs[cs].csor); + csor_ext = ioread32be(&ifc->csor_cs[cs].csor_ext); + + /* chage PageSize 8K and SpareSize 1K*/ + csor_8k = (csor & ~(CSOR_NAND_PGS_MASK)) | 0x0018C000; + iowrite32be(csor_8k, &ifc->csor_cs[cs].csor); + iowrite32be(0x0000400, &ifc->csor_cs[cs].csor_ext); + + /* READID */ + iowrite32be((IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RB << IFC_NAND_FIR0_OP2_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be(NAND_CMD_READID << IFC_NAND_FCR0_CMD0_SHIFT, + &ifc->ifc_nand.nand_fcr0); + iowrite32be(0x0, &ifc->ifc_nand.row3); + + iowrite32be(0x0, &ifc->ifc_nand.nand_fbcr); + + /* Program ROW0/COL0 */ + iowrite32be(0x0, &ifc->ifc_nand.row0); + iowrite32be(0x0, &ifc->ifc_nand.col0); + + /* set the chip select for NAND Transaction */ + iowrite32be(cs << IFC_NAND_CSEL_SHIFT, &ifc->ifc_nand.nand_csel); + + /* start read seq */ + iowrite32be(IFC_NAND_SEQ_STRT_FIR_STRT, &ifc->ifc_nand.nandseq_strt); + + /* wait for command complete flag or timeout */ + wait_event_timeout(ctrl->nand_wait, ctrl->nand_stat, + msecs_to_jiffies(IFC_TIMEOUT_MSECS)); + + if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC) + printk(KERN_ERR "fsl-ifc: Failed to Initialise SRAM\n"); + + /* Restore CSOR and CSOR_ext */ + iowrite32be(csor, &ifc->csor_cs[cs].csor); + iowrite32be(csor_ext, &ifc->csor_cs[cs].csor_ext); +} + +static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) +{ + struct fsl_ifc_ctrl *ctrl = priv->ctrl; + struct fsl_ifc_regs __iomem *ifc = ctrl->regs; + struct nand_chip *chip = &priv->chip; + struct nand_ecclayout *layout; + u32 csor; + + /* Fill in fsl_ifc_mtd structure */ + priv->mtd.priv = chip; + priv->mtd.owner = THIS_MODULE; + + /* fill in nand_chip structure */ + /* set up function call table */ + if ((ioread32be(&ifc->cspr_cs[priv->bank].cspr)) & CSPR_PORT_SIZE_16) + chip->read_byte = fsl_ifc_read_byte16; + else + chip->read_byte = fsl_ifc_read_byte; + + chip->write_buf = fsl_ifc_write_buf; + chip->read_buf = fsl_ifc_read_buf; + chip->select_chip = fsl_ifc_select_chip; + chip->cmdfunc = fsl_ifc_cmdfunc; + chip->waitfunc = fsl_ifc_wait; + + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + + iowrite32be(0x0, &ifc->ifc_nand.ncfgr); + + /* set up nand options */ + chip->bbt_options = NAND_BBT_USE_FLASH; + chip->options = NAND_NO_SUBPAGE_WRITE; + + if (ioread32be(&ifc->cspr_cs[priv->bank].cspr) & CSPR_PORT_SIZE_16) { + chip->read_byte = fsl_ifc_read_byte16; + chip->options |= NAND_BUSWIDTH_16; + } else { + chip->read_byte = fsl_ifc_read_byte; + } + + chip->controller = &ifc_nand_ctrl->controller; + chip->priv = priv; + + chip->ecc.read_page = fsl_ifc_read_page; + chip->ecc.write_page = fsl_ifc_write_page; + + csor = ioread32be(&ifc->csor_cs[priv->bank].csor); + + /* Hardware generates ECC per 512 Bytes */ + chip->ecc.size = 512; + chip->ecc.bytes = 8; + chip->ecc.strength = 4; + + switch (csor & CSOR_NAND_PGS_MASK) { + case CSOR_NAND_PGS_512: + if (chip->options & NAND_BUSWIDTH_16) { + layout = &oob_512_16bit_ecc4; + } else { + layout = &oob_512_8bit_ecc4; + + /* Avoid conflict with bad block marker */ + bbt_main_descr.offs = 0; + bbt_mirror_descr.offs = 0; + } + + priv->bufnum_mask = 15; + break; + + case CSOR_NAND_PGS_2K: + layout = &oob_2048_ecc4; + priv->bufnum_mask = 3; + break; + + case CSOR_NAND_PGS_4K: + if ((csor & CSOR_NAND_ECC_MODE_MASK) == + CSOR_NAND_ECC_MODE_4) { + layout = &oob_4096_ecc4; + } else { + layout = &oob_4096_ecc8; + chip->ecc.bytes = 16; + chip->ecc.strength = 8; + } + + priv->bufnum_mask = 1; + break; + + case CSOR_NAND_PGS_8K: + if ((csor & CSOR_NAND_ECC_MODE_MASK) == + CSOR_NAND_ECC_MODE_4) { + layout = &oob_8192_ecc4; + } else { + layout = &oob_8192_ecc8; + chip->ecc.bytes = 16; + chip->ecc.strength = 8; + } + + priv->bufnum_mask = 0; + break; + + default: + dev_err(priv->dev, "bad csor %#x: bad page size\n", csor); + return -ENODEV; + } + + /* Must also set CSOR_NAND_ECC_ENC_EN if DEC_EN set */ + if (csor & CSOR_NAND_ECC_DEC_EN) { + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.layout = layout; + } else { + chip->ecc.mode = NAND_ECC_SOFT; + } + + if (ctrl->version == FSL_IFC_VERSION_1_1_0) + fsl_ifc_sram_init(priv); + + return 0; +} + +static int fsl_ifc_chip_remove(struct fsl_ifc_mtd *priv) +{ + nand_release(&priv->mtd); + + kfree(priv->mtd.name); + + if (priv->vbase) + iounmap(priv->vbase); + + ifc_nand_ctrl->chips[priv->bank] = NULL; + + return 0; +} + +static int match_bank(struct fsl_ifc_regs __iomem *ifc, int bank, + phys_addr_t addr) +{ + u32 cspr = ioread32be(&ifc->cspr_cs[bank].cspr); + + if (!(cspr & CSPR_V)) + return 0; + if ((cspr & CSPR_MSEL) != CSPR_MSEL_NAND) + return 0; + + return (cspr & CSPR_BA) == convert_ifc_address(addr); +} + +static DEFINE_MUTEX(fsl_ifc_nand_mutex); + +static int fsl_ifc_nand_probe(struct platform_device *dev) +{ + struct fsl_ifc_regs __iomem *ifc; + struct fsl_ifc_mtd *priv; + struct resource res; + static const char *part_probe_types[] + = { "cmdlinepart", "RedBoot", "ofpart", NULL }; + int ret; + int bank; + struct device_node *node = dev->dev.of_node; + struct mtd_part_parser_data ppdata; + + ppdata.of_node = dev->dev.of_node; + if (!fsl_ifc_ctrl_dev || !fsl_ifc_ctrl_dev->regs) + return -ENODEV; + ifc = fsl_ifc_ctrl_dev->regs; + + /* get, allocate and map the memory resource */ + ret = of_address_to_resource(node, 0, &res); + if (ret) { + dev_err(&dev->dev, "%s: failed to get resource\n", __func__); + return ret; + } + + /* find which chip select it is connected to */ + for (bank = 0; bank < fsl_ifc_ctrl_dev->banks; bank++) { + if (match_bank(ifc, bank, res.start)) + break; + } + + if (bank >= fsl_ifc_ctrl_dev->banks) { + dev_err(&dev->dev, "%s: address did not match any chip selects\n", + __func__); + return -ENODEV; + } + + priv = devm_kzalloc(&dev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + mutex_lock(&fsl_ifc_nand_mutex); + if (!fsl_ifc_ctrl_dev->nand) { + ifc_nand_ctrl = kzalloc(sizeof(*ifc_nand_ctrl), GFP_KERNEL); + if (!ifc_nand_ctrl) { + mutex_unlock(&fsl_ifc_nand_mutex); + return -ENOMEM; + } + + ifc_nand_ctrl->read_bytes = 0; + ifc_nand_ctrl->index = 0; + ifc_nand_ctrl->addr = NULL; + fsl_ifc_ctrl_dev->nand = ifc_nand_ctrl; + + spin_lock_init(&ifc_nand_ctrl->controller.lock); + init_waitqueue_head(&ifc_nand_ctrl->controller.wq); + } else { + ifc_nand_ctrl = fsl_ifc_ctrl_dev->nand; + } + mutex_unlock(&fsl_ifc_nand_mutex); + + ifc_nand_ctrl->chips[bank] = priv; + priv->bank = bank; + priv->ctrl = fsl_ifc_ctrl_dev; + priv->dev = &dev->dev; + + priv->vbase = ioremap(res.start, resource_size(&res)); + if (!priv->vbase) { + dev_err(priv->dev, "%s: failed to map chip region\n", __func__); + ret = -ENOMEM; + goto err; + } + + dev_set_drvdata(priv->dev, priv); + + iowrite32be(IFC_NAND_EVTER_EN_OPC_EN | + IFC_NAND_EVTER_EN_FTOER_EN | + IFC_NAND_EVTER_EN_WPER_EN, + &ifc->ifc_nand.nand_evter_en); + + /* enable NAND Machine Interrupts */ + iowrite32be(IFC_NAND_EVTER_INTR_OPCIR_EN | + IFC_NAND_EVTER_INTR_FTOERIR_EN | + IFC_NAND_EVTER_INTR_WPERIR_EN, + &ifc->ifc_nand.nand_evter_intr_en); + priv->mtd.name = kasprintf(GFP_KERNEL, "%llx.flash", (u64)res.start); + if (!priv->mtd.name) { + ret = -ENOMEM; + goto err; + } + + ret = fsl_ifc_chip_init(priv); + if (ret) + goto err; + + ret = nand_scan_ident(&priv->mtd, 1, NULL); + if (ret) + goto err; + + ret = fsl_ifc_chip_init_tail(&priv->mtd); + if (ret) + goto err; + + ret = nand_scan_tail(&priv->mtd); + if (ret) + goto err; + + /* First look for RedBoot table or partitions on the command + * line, these take precedence over device tree information */ + mtd_device_parse_register(&priv->mtd, part_probe_types, &ppdata, + NULL, 0); + + dev_info(priv->dev, "IFC NAND device at 0x%llx, bank %d\n", + (unsigned long long)res.start, priv->bank); + return 0; + +err: + fsl_ifc_chip_remove(priv); + return ret; +} + +static int fsl_ifc_nand_remove(struct platform_device *dev) +{ + struct fsl_ifc_mtd *priv = dev_get_drvdata(&dev->dev); + + fsl_ifc_chip_remove(priv); + + mutex_lock(&fsl_ifc_nand_mutex); + ifc_nand_ctrl->counter--; + if (!ifc_nand_ctrl->counter) { + fsl_ifc_ctrl_dev->nand = NULL; + kfree(ifc_nand_ctrl); + } + mutex_unlock(&fsl_ifc_nand_mutex); + + return 0; +} + +static const struct of_device_id fsl_ifc_nand_match[] = { + { + .compatible = "fsl,ifc-nand", + }, + {} +}; + +static struct platform_driver fsl_ifc_nand_driver = { + .driver = { + .name = "fsl,ifc-nand", + .of_match_table = fsl_ifc_nand_match, + }, + .probe = fsl_ifc_nand_probe, + .remove = fsl_ifc_nand_remove, +}; + +module_platform_driver(fsl_ifc_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Freescale"); +MODULE_DESCRIPTION("Freescale Integrated Flash Controller MTD NAND driver"); diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/fsl_upm.c new file mode 100644 index 000000000..72755d7ec --- /dev/null +++ b/drivers/mtd/nand/fsl_upm.c @@ -0,0 +1,361 @@ +/* + * Freescale UPM NAND driver. + * + * Copyright © 2007-2008 MontaVista Software, Inc. + * + * Author: Anton Vorontsov <avorontsov@ru.mvista.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/mtd.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/of_gpio.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <asm/fsl_lbc.h> + +#define FSL_UPM_WAIT_RUN_PATTERN 0x1 +#define FSL_UPM_WAIT_WRITE_BYTE 0x2 +#define FSL_UPM_WAIT_WRITE_BUFFER 0x4 + +struct fsl_upm_nand { + struct device *dev; + struct mtd_info mtd; + struct nand_chip chip; + int last_ctrl; + struct mtd_partition *parts; + struct fsl_upm upm; + uint8_t upm_addr_offset; + uint8_t upm_cmd_offset; + void __iomem *io_base; + int rnb_gpio[NAND_MAX_CHIPS]; + uint32_t mchip_offsets[NAND_MAX_CHIPS]; + uint32_t mchip_count; + uint32_t mchip_number; + int chip_delay; + uint32_t wait_flags; +}; + +static inline struct fsl_upm_nand *to_fsl_upm_nand(struct mtd_info *mtdinfo) +{ + return container_of(mtdinfo, struct fsl_upm_nand, mtd); +} + +static int fun_chip_ready(struct mtd_info *mtd) +{ + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + + if (gpio_get_value(fun->rnb_gpio[fun->mchip_number])) + return 1; + + dev_vdbg(fun->dev, "busy\n"); + return 0; +} + +static void fun_wait_rnb(struct fsl_upm_nand *fun) +{ + if (fun->rnb_gpio[fun->mchip_number] >= 0) { + int cnt = 1000000; + + while (--cnt && !fun_chip_ready(&fun->mtd)) + cpu_relax(); + if (!cnt) + dev_err(fun->dev, "tired waiting for RNB\n"); + } else { + ndelay(100); + } +} + +static void fun_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + u32 mar; + + if (!(ctrl & fun->last_ctrl)) { + fsl_upm_end_pattern(&fun->upm); + + if (cmd == NAND_CMD_NONE) + return; + + fun->last_ctrl = ctrl & (NAND_ALE | NAND_CLE); + } + + if (ctrl & NAND_CTRL_CHANGE) { + if (ctrl & NAND_ALE) + fsl_upm_start_pattern(&fun->upm, fun->upm_addr_offset); + else if (ctrl & NAND_CLE) + fsl_upm_start_pattern(&fun->upm, fun->upm_cmd_offset); + } + + mar = (cmd << (32 - fun->upm.width)) | + fun->mchip_offsets[fun->mchip_number]; + fsl_upm_run_pattern(&fun->upm, chip->IO_ADDR_R, mar); + + if (fun->wait_flags & FSL_UPM_WAIT_RUN_PATTERN) + fun_wait_rnb(fun); +} + +static void fun_select_chip(struct mtd_info *mtd, int mchip_nr) +{ + struct nand_chip *chip = mtd->priv; + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + + if (mchip_nr == -1) { + chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); + } else if (mchip_nr >= 0 && mchip_nr < NAND_MAX_CHIPS) { + fun->mchip_number = mchip_nr; + chip->IO_ADDR_R = fun->io_base + fun->mchip_offsets[mchip_nr]; + chip->IO_ADDR_W = chip->IO_ADDR_R; + } else { + BUG(); + } +} + +static uint8_t fun_read_byte(struct mtd_info *mtd) +{ + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + + return in_8(fun->chip.IO_ADDR_R); +} + +static void fun_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + int i; + + for (i = 0; i < len; i++) + buf[i] = in_8(fun->chip.IO_ADDR_R); +} + +static void fun_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct fsl_upm_nand *fun = to_fsl_upm_nand(mtd); + int i; + + for (i = 0; i < len; i++) { + out_8(fun->chip.IO_ADDR_W, buf[i]); + if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BYTE) + fun_wait_rnb(fun); + } + if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BUFFER) + fun_wait_rnb(fun); +} + +static int fun_chip_init(struct fsl_upm_nand *fun, + const struct device_node *upm_np, + const struct resource *io_res) +{ + int ret; + struct device_node *flash_np; + struct mtd_part_parser_data ppdata; + + fun->chip.IO_ADDR_R = fun->io_base; + fun->chip.IO_ADDR_W = fun->io_base; + fun->chip.cmd_ctrl = fun_cmd_ctrl; + fun->chip.chip_delay = fun->chip_delay; + fun->chip.read_byte = fun_read_byte; + fun->chip.read_buf = fun_read_buf; + fun->chip.write_buf = fun_write_buf; + fun->chip.ecc.mode = NAND_ECC_SOFT; + if (fun->mchip_count > 1) + fun->chip.select_chip = fun_select_chip; + + if (fun->rnb_gpio[0] >= 0) + fun->chip.dev_ready = fun_chip_ready; + + fun->mtd.priv = &fun->chip; + fun->mtd.owner = THIS_MODULE; + + flash_np = of_get_next_child(upm_np, NULL); + if (!flash_np) + return -ENODEV; + + fun->mtd.name = kasprintf(GFP_KERNEL, "0x%llx.%s", (u64)io_res->start, + flash_np->name); + if (!fun->mtd.name) { + ret = -ENOMEM; + goto err; + } + + ret = nand_scan(&fun->mtd, fun->mchip_count); + if (ret) + goto err; + + ppdata.of_node = flash_np; + ret = mtd_device_parse_register(&fun->mtd, NULL, &ppdata, NULL, 0); +err: + of_node_put(flash_np); + if (ret) + kfree(fun->mtd.name); + return ret; +} + +static int fun_probe(struct platform_device *ofdev) +{ + struct fsl_upm_nand *fun; + struct resource io_res; + const __be32 *prop; + int rnb_gpio; + int ret; + int size; + int i; + + fun = kzalloc(sizeof(*fun), GFP_KERNEL); + if (!fun) + return -ENOMEM; + + ret = of_address_to_resource(ofdev->dev.of_node, 0, &io_res); + if (ret) { + dev_err(&ofdev->dev, "can't get IO base\n"); + goto err1; + } + + ret = fsl_upm_find(io_res.start, &fun->upm); + if (ret) { + dev_err(&ofdev->dev, "can't find UPM\n"); + goto err1; + } + + prop = of_get_property(ofdev->dev.of_node, "fsl,upm-addr-offset", + &size); + if (!prop || size != sizeof(uint32_t)) { + dev_err(&ofdev->dev, "can't get UPM address offset\n"); + ret = -EINVAL; + goto err1; + } + fun->upm_addr_offset = *prop; + + prop = of_get_property(ofdev->dev.of_node, "fsl,upm-cmd-offset", &size); + if (!prop || size != sizeof(uint32_t)) { + dev_err(&ofdev->dev, "can't get UPM command offset\n"); + ret = -EINVAL; + goto err1; + } + fun->upm_cmd_offset = *prop; + + prop = of_get_property(ofdev->dev.of_node, + "fsl,upm-addr-line-cs-offsets", &size); + if (prop && (size / sizeof(uint32_t)) > 0) { + fun->mchip_count = size / sizeof(uint32_t); + if (fun->mchip_count >= NAND_MAX_CHIPS) { + dev_err(&ofdev->dev, "too much multiple chips\n"); + goto err1; + } + for (i = 0; i < fun->mchip_count; i++) + fun->mchip_offsets[i] = be32_to_cpu(prop[i]); + } else { + fun->mchip_count = 1; + } + + for (i = 0; i < fun->mchip_count; i++) { + fun->rnb_gpio[i] = -1; + rnb_gpio = of_get_gpio(ofdev->dev.of_node, i); + if (rnb_gpio >= 0) { + ret = gpio_request(rnb_gpio, dev_name(&ofdev->dev)); + if (ret) { + dev_err(&ofdev->dev, + "can't request RNB gpio #%d\n", i); + goto err2; + } + gpio_direction_input(rnb_gpio); + fun->rnb_gpio[i] = rnb_gpio; + } else if (rnb_gpio == -EINVAL) { + dev_err(&ofdev->dev, "RNB gpio #%d is invalid\n", i); + goto err2; + } + } + + prop = of_get_property(ofdev->dev.of_node, "chip-delay", NULL); + if (prop) + fun->chip_delay = be32_to_cpup(prop); + else + fun->chip_delay = 50; + + prop = of_get_property(ofdev->dev.of_node, "fsl,upm-wait-flags", &size); + if (prop && size == sizeof(uint32_t)) + fun->wait_flags = be32_to_cpup(prop); + else + fun->wait_flags = FSL_UPM_WAIT_RUN_PATTERN | + FSL_UPM_WAIT_WRITE_BYTE; + + fun->io_base = devm_ioremap_nocache(&ofdev->dev, io_res.start, + resource_size(&io_res)); + if (!fun->io_base) { + ret = -ENOMEM; + goto err2; + } + + fun->dev = &ofdev->dev; + fun->last_ctrl = NAND_CLE; + + ret = fun_chip_init(fun, ofdev->dev.of_node, &io_res); + if (ret) + goto err2; + + dev_set_drvdata(&ofdev->dev, fun); + + return 0; +err2: + for (i = 0; i < fun->mchip_count; i++) { + if (fun->rnb_gpio[i] < 0) + break; + gpio_free(fun->rnb_gpio[i]); + } +err1: + kfree(fun); + + return ret; +} + +static int fun_remove(struct platform_device *ofdev) +{ + struct fsl_upm_nand *fun = dev_get_drvdata(&ofdev->dev); + int i; + + nand_release(&fun->mtd); + kfree(fun->mtd.name); + + for (i = 0; i < fun->mchip_count; i++) { + if (fun->rnb_gpio[i] < 0) + break; + gpio_free(fun->rnb_gpio[i]); + } + + kfree(fun); + + return 0; +} + +static const struct of_device_id of_fun_match[] = { + { .compatible = "fsl,upm-nand" }, + {}, +}; +MODULE_DEVICE_TABLE(of, of_fun_match); + +static struct platform_driver of_fun_driver = { + .driver = { + .name = "fsl,upm-nand", + .of_match_table = of_fun_match, + }, + .probe = fun_probe, + .remove = fun_remove, +}; + +module_platform_driver(of_fun_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Anton Vorontsov <avorontsov@ru.mvista.com>"); +MODULE_DESCRIPTION("Driver for NAND chips working through Freescale " + "LocalBus User-Programmable Machine"); diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c new file mode 100644 index 000000000..e58af4bfa --- /dev/null +++ b/drivers/mtd/nand/fsmc_nand.c @@ -0,0 +1,1242 @@ +/* + * drivers/mtd/nand/fsmc_nand.c + * + * ST Microelectronics + * Flexible Static Memory Controller (FSMC) + * Driver for NAND portions + * + * Copyright © 2010 ST Microelectronics + * Vipin Kumar <vipin.kumar@st.com> + * Ashish Priyadarshi + * + * Based on drivers/mtd/nand/nomadik_nand.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/dmaengine.h> +#include <linux/dma-direction.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/resource.h> +#include <linux/sched.h> +#include <linux/types.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/mtd/partitions.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/mtd/fsmc.h> +#include <linux/amba/bus.h> +#include <mtd/mtd-abi.h> + +static struct nand_ecclayout fsmc_ecc1_128_layout = { + .eccbytes = 24, + .eccpos = {2, 3, 4, 18, 19, 20, 34, 35, 36, 50, 51, 52, + 66, 67, 68, 82, 83, 84, 98, 99, 100, 114, 115, 116}, + .oobfree = { + {.offset = 8, .length = 8}, + {.offset = 24, .length = 8}, + {.offset = 40, .length = 8}, + {.offset = 56, .length = 8}, + {.offset = 72, .length = 8}, + {.offset = 88, .length = 8}, + {.offset = 104, .length = 8}, + {.offset = 120, .length = 8} + } +}; + +static struct nand_ecclayout fsmc_ecc1_64_layout = { + .eccbytes = 12, + .eccpos = {2, 3, 4, 18, 19, 20, 34, 35, 36, 50, 51, 52}, + .oobfree = { + {.offset = 8, .length = 8}, + {.offset = 24, .length = 8}, + {.offset = 40, .length = 8}, + {.offset = 56, .length = 8}, + } +}; + +static struct nand_ecclayout fsmc_ecc1_16_layout = { + .eccbytes = 3, + .eccpos = {2, 3, 4}, + .oobfree = { + {.offset = 8, .length = 8}, + } +}; + +/* + * ECC4 layout for NAND of pagesize 8192 bytes & OOBsize 256 bytes. 13*16 bytes + * of OB size is reserved for ECC, Byte no. 0 & 1 reserved for bad block and 46 + * bytes are free for use. + */ +static struct nand_ecclayout fsmc_ecc4_256_layout = { + .eccbytes = 208, + .eccpos = { 2, 3, 4, 5, 6, 7, 8, + 9, 10, 11, 12, 13, 14, + 18, 19, 20, 21, 22, 23, 24, + 25, 26, 27, 28, 29, 30, + 34, 35, 36, 37, 38, 39, 40, + 41, 42, 43, 44, 45, 46, + 50, 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + 66, 67, 68, 69, 70, 71, 72, + 73, 74, 75, 76, 77, 78, + 82, 83, 84, 85, 86, 87, 88, + 89, 90, 91, 92, 93, 94, + 98, 99, 100, 101, 102, 103, 104, + 105, 106, 107, 108, 109, 110, + 114, 115, 116, 117, 118, 119, 120, + 121, 122, 123, 124, 125, 126, + 130, 131, 132, 133, 134, 135, 136, + 137, 138, 139, 140, 141, 142, + 146, 147, 148, 149, 150, 151, 152, + 153, 154, 155, 156, 157, 158, + 162, 163, 164, 165, 166, 167, 168, + 169, 170, 171, 172, 173, 174, + 178, 179, 180, 181, 182, 183, 184, + 185, 186, 187, 188, 189, 190, + 194, 195, 196, 197, 198, 199, 200, + 201, 202, 203, 204, 205, 206, + 210, 211, 212, 213, 214, 215, 216, + 217, 218, 219, 220, 221, 222, + 226, 227, 228, 229, 230, 231, 232, + 233, 234, 235, 236, 237, 238, + 242, 243, 244, 245, 246, 247, 248, + 249, 250, 251, 252, 253, 254 + }, + .oobfree = { + {.offset = 15, .length = 3}, + {.offset = 31, .length = 3}, + {.offset = 47, .length = 3}, + {.offset = 63, .length = 3}, + {.offset = 79, .length = 3}, + {.offset = 95, .length = 3}, + {.offset = 111, .length = 3}, + {.offset = 127, .length = 3}, + {.offset = 143, .length = 3}, + {.offset = 159, .length = 3}, + {.offset = 175, .length = 3}, + {.offset = 191, .length = 3}, + {.offset = 207, .length = 3}, + {.offset = 223, .length = 3}, + {.offset = 239, .length = 3}, + {.offset = 255, .length = 1} + } +}; + +/* + * ECC4 layout for NAND of pagesize 4096 bytes & OOBsize 224 bytes. 13*8 bytes + * of OOB size is reserved for ECC, Byte no. 0 & 1 reserved for bad block & 118 + * bytes are free for use. + */ +static struct nand_ecclayout fsmc_ecc4_224_layout = { + .eccbytes = 104, + .eccpos = { 2, 3, 4, 5, 6, 7, 8, + 9, 10, 11, 12, 13, 14, + 18, 19, 20, 21, 22, 23, 24, + 25, 26, 27, 28, 29, 30, + 34, 35, 36, 37, 38, 39, 40, + 41, 42, 43, 44, 45, 46, + 50, 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + 66, 67, 68, 69, 70, 71, 72, + 73, 74, 75, 76, 77, 78, + 82, 83, 84, 85, 86, 87, 88, + 89, 90, 91, 92, 93, 94, + 98, 99, 100, 101, 102, 103, 104, + 105, 106, 107, 108, 109, 110, + 114, 115, 116, 117, 118, 119, 120, + 121, 122, 123, 124, 125, 126 + }, + .oobfree = { + {.offset = 15, .length = 3}, + {.offset = 31, .length = 3}, + {.offset = 47, .length = 3}, + {.offset = 63, .length = 3}, + {.offset = 79, .length = 3}, + {.offset = 95, .length = 3}, + {.offset = 111, .length = 3}, + {.offset = 127, .length = 97} + } +}; + +/* + * ECC4 layout for NAND of pagesize 4096 bytes & OOBsize 128 bytes. 13*8 bytes + * of OOB size is reserved for ECC, Byte no. 0 & 1 reserved for bad block & 22 + * bytes are free for use. + */ +static struct nand_ecclayout fsmc_ecc4_128_layout = { + .eccbytes = 104, + .eccpos = { 2, 3, 4, 5, 6, 7, 8, + 9, 10, 11, 12, 13, 14, + 18, 19, 20, 21, 22, 23, 24, + 25, 26, 27, 28, 29, 30, + 34, 35, 36, 37, 38, 39, 40, + 41, 42, 43, 44, 45, 46, + 50, 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + 66, 67, 68, 69, 70, 71, 72, + 73, 74, 75, 76, 77, 78, + 82, 83, 84, 85, 86, 87, 88, + 89, 90, 91, 92, 93, 94, + 98, 99, 100, 101, 102, 103, 104, + 105, 106, 107, 108, 109, 110, + 114, 115, 116, 117, 118, 119, 120, + 121, 122, 123, 124, 125, 126 + }, + .oobfree = { + {.offset = 15, .length = 3}, + {.offset = 31, .length = 3}, + {.offset = 47, .length = 3}, + {.offset = 63, .length = 3}, + {.offset = 79, .length = 3}, + {.offset = 95, .length = 3}, + {.offset = 111, .length = 3}, + {.offset = 127, .length = 1} + } +}; + +/* + * ECC4 layout for NAND of pagesize 2048 bytes & OOBsize 64 bytes. 13*4 bytes of + * OOB size is reserved for ECC, Byte no. 0 & 1 reserved for bad block and 10 + * bytes are free for use. + */ +static struct nand_ecclayout fsmc_ecc4_64_layout = { + .eccbytes = 52, + .eccpos = { 2, 3, 4, 5, 6, 7, 8, + 9, 10, 11, 12, 13, 14, + 18, 19, 20, 21, 22, 23, 24, + 25, 26, 27, 28, 29, 30, + 34, 35, 36, 37, 38, 39, 40, + 41, 42, 43, 44, 45, 46, + 50, 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + }, + .oobfree = { + {.offset = 15, .length = 3}, + {.offset = 31, .length = 3}, + {.offset = 47, .length = 3}, + {.offset = 63, .length = 1}, + } +}; + +/* + * ECC4 layout for NAND of pagesize 512 bytes & OOBsize 16 bytes. 13 bytes of + * OOB size is reserved for ECC, Byte no. 4 & 5 reserved for bad block and One + * byte is free for use. + */ +static struct nand_ecclayout fsmc_ecc4_16_layout = { + .eccbytes = 13, + .eccpos = { 0, 1, 2, 3, 6, 7, 8, + 9, 10, 11, 12, 13, 14 + }, + .oobfree = { + {.offset = 15, .length = 1}, + } +}; + +/* + * ECC placement definitions in oobfree type format. + * There are 13 bytes of ecc for every 512 byte block and it has to be read + * consecutively and immediately after the 512 byte data block for hardware to + * generate the error bit offsets in 512 byte data. + * Managing the ecc bytes in the following way makes it easier for software to + * read ecc bytes consecutive to data bytes. This way is similar to + * oobfree structure maintained already in generic nand driver + */ +static struct fsmc_eccplace fsmc_ecc4_lp_place = { + .eccplace = { + {.offset = 2, .length = 13}, + {.offset = 18, .length = 13}, + {.offset = 34, .length = 13}, + {.offset = 50, .length = 13}, + {.offset = 66, .length = 13}, + {.offset = 82, .length = 13}, + {.offset = 98, .length = 13}, + {.offset = 114, .length = 13} + } +}; + +static struct fsmc_eccplace fsmc_ecc4_sp_place = { + .eccplace = { + {.offset = 0, .length = 4}, + {.offset = 6, .length = 9} + } +}; + +/** + * struct fsmc_nand_data - structure for FSMC NAND device state + * + * @pid: Part ID on the AMBA PrimeCell format + * @mtd: MTD info for a NAND flash. + * @nand: Chip related info for a NAND flash. + * @partitions: Partition info for a NAND Flash. + * @nr_partitions: Total number of partition of a NAND flash. + * + * @ecc_place: ECC placing locations in oobfree type format. + * @bank: Bank number for probed device. + * @clk: Clock structure for FSMC. + * + * @read_dma_chan: DMA channel for read access + * @write_dma_chan: DMA channel for write access to NAND + * @dma_access_complete: Completion structure + * + * @data_pa: NAND Physical port for Data. + * @data_va: NAND port for Data. + * @cmd_va: NAND port for Command. + * @addr_va: NAND port for Address. + * @regs_va: FSMC regs base address. + */ +struct fsmc_nand_data { + u32 pid; + struct mtd_info mtd; + struct nand_chip nand; + struct mtd_partition *partitions; + unsigned int nr_partitions; + + struct fsmc_eccplace *ecc_place; + unsigned int bank; + struct device *dev; + enum access_mode mode; + struct clk *clk; + + /* DMA related objects */ + struct dma_chan *read_dma_chan; + struct dma_chan *write_dma_chan; + struct completion dma_access_complete; + + struct fsmc_nand_timings *dev_timings; + + dma_addr_t data_pa; + void __iomem *data_va; + void __iomem *cmd_va; + void __iomem *addr_va; + void __iomem *regs_va; + + void (*select_chip)(uint32_t bank, uint32_t busw); +}; + +/* Assert CS signal based on chipnr */ +static void fsmc_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct nand_chip *chip = mtd->priv; + struct fsmc_nand_data *host; + + host = container_of(mtd, struct fsmc_nand_data, mtd); + + switch (chipnr) { + case -1: + chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); + break; + case 0: + case 1: + case 2: + case 3: + if (host->select_chip) + host->select_chip(chipnr, + chip->options & NAND_BUSWIDTH_16); + break; + + default: + BUG(); + } +} + +/* + * fsmc_cmd_ctrl - For facilitaing Hardware access + * This routine allows hardware specific access to control-lines(ALE,CLE) + */ +static void fsmc_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *this = mtd->priv; + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + void __iomem *regs = host->regs_va; + unsigned int bank = host->bank; + + if (ctrl & NAND_CTRL_CHANGE) { + u32 pc; + + if (ctrl & NAND_CLE) { + this->IO_ADDR_R = host->cmd_va; + this->IO_ADDR_W = host->cmd_va; + } else if (ctrl & NAND_ALE) { + this->IO_ADDR_R = host->addr_va; + this->IO_ADDR_W = host->addr_va; + } else { + this->IO_ADDR_R = host->data_va; + this->IO_ADDR_W = host->data_va; + } + + pc = readl(FSMC_NAND_REG(regs, bank, PC)); + if (ctrl & NAND_NCE) + pc |= FSMC_ENABLE; + else + pc &= ~FSMC_ENABLE; + writel_relaxed(pc, FSMC_NAND_REG(regs, bank, PC)); + } + + mb(); + + if (cmd != NAND_CMD_NONE) + writeb_relaxed(cmd, this->IO_ADDR_W); +} + +/* + * fsmc_nand_setup - FSMC (Flexible Static Memory Controller) init routine + * + * This routine initializes timing parameters related to NAND memory access in + * FSMC registers + */ +static void fsmc_nand_setup(void __iomem *regs, uint32_t bank, + uint32_t busw, struct fsmc_nand_timings *timings) +{ + uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON; + uint32_t tclr, tar, thiz, thold, twait, tset; + struct fsmc_nand_timings *tims; + struct fsmc_nand_timings default_timings = { + .tclr = FSMC_TCLR_1, + .tar = FSMC_TAR_1, + .thiz = FSMC_THIZ_1, + .thold = FSMC_THOLD_4, + .twait = FSMC_TWAIT_6, + .tset = FSMC_TSET_0, + }; + + if (timings) + tims = timings; + else + tims = &default_timings; + + tclr = (tims->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT; + tar = (tims->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT; + thiz = (tims->thiz & FSMC_THIZ_MASK) << FSMC_THIZ_SHIFT; + thold = (tims->thold & FSMC_THOLD_MASK) << FSMC_THOLD_SHIFT; + twait = (tims->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT; + tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; + + if (busw) + writel_relaxed(value | FSMC_DEVWID_16, + FSMC_NAND_REG(regs, bank, PC)); + else + writel_relaxed(value | FSMC_DEVWID_8, + FSMC_NAND_REG(regs, bank, PC)); + + writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) | tclr | tar, + FSMC_NAND_REG(regs, bank, PC)); + writel_relaxed(thiz | thold | twait | tset, + FSMC_NAND_REG(regs, bank, COMM)); + writel_relaxed(thiz | thold | twait | tset, + FSMC_NAND_REG(regs, bank, ATTRIB)); +} + +/* + * fsmc_enable_hwecc - Enables Hardware ECC through FSMC registers + */ +static void fsmc_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + void __iomem *regs = host->regs_va; + uint32_t bank = host->bank; + + writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) & ~FSMC_ECCPLEN_256, + FSMC_NAND_REG(regs, bank, PC)); + writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) & ~FSMC_ECCEN, + FSMC_NAND_REG(regs, bank, PC)); + writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) | FSMC_ECCEN, + FSMC_NAND_REG(regs, bank, PC)); +} + +/* + * fsmc_read_hwecc_ecc4 - Hardware ECC calculator for ecc4 option supported by + * FSMC. ECC is 13 bytes for 512 bytes of data (supports error correction up to + * max of 8-bits) + */ +static int fsmc_read_hwecc_ecc4(struct mtd_info *mtd, const uint8_t *data, + uint8_t *ecc) +{ + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + void __iomem *regs = host->regs_va; + uint32_t bank = host->bank; + uint32_t ecc_tmp; + unsigned long deadline = jiffies + FSMC_BUSY_WAIT_TIMEOUT; + + do { + if (readl_relaxed(FSMC_NAND_REG(regs, bank, STS)) & FSMC_CODE_RDY) + break; + else + cond_resched(); + } while (!time_after_eq(jiffies, deadline)); + + if (time_after_eq(jiffies, deadline)) { + dev_err(host->dev, "calculate ecc timed out\n"); + return -ETIMEDOUT; + } + + ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1)); + ecc[0] = (uint8_t) (ecc_tmp >> 0); + ecc[1] = (uint8_t) (ecc_tmp >> 8); + ecc[2] = (uint8_t) (ecc_tmp >> 16); + ecc[3] = (uint8_t) (ecc_tmp >> 24); + + ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC2)); + ecc[4] = (uint8_t) (ecc_tmp >> 0); + ecc[5] = (uint8_t) (ecc_tmp >> 8); + ecc[6] = (uint8_t) (ecc_tmp >> 16); + ecc[7] = (uint8_t) (ecc_tmp >> 24); + + ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC3)); + ecc[8] = (uint8_t) (ecc_tmp >> 0); + ecc[9] = (uint8_t) (ecc_tmp >> 8); + ecc[10] = (uint8_t) (ecc_tmp >> 16); + ecc[11] = (uint8_t) (ecc_tmp >> 24); + + ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, STS)); + ecc[12] = (uint8_t) (ecc_tmp >> 16); + + return 0; +} + +/* + * fsmc_read_hwecc_ecc1 - Hardware ECC calculator for ecc1 option supported by + * FSMC. ECC is 3 bytes for 512 bytes of data (supports error correction up to + * max of 1-bit) + */ +static int fsmc_read_hwecc_ecc1(struct mtd_info *mtd, const uint8_t *data, + uint8_t *ecc) +{ + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + void __iomem *regs = host->regs_va; + uint32_t bank = host->bank; + uint32_t ecc_tmp; + + ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1)); + ecc[0] = (uint8_t) (ecc_tmp >> 0); + ecc[1] = (uint8_t) (ecc_tmp >> 8); + ecc[2] = (uint8_t) (ecc_tmp >> 16); + + return 0; +} + +/* Count the number of 0's in buff upto a max of max_bits */ +static int count_written_bits(uint8_t *buff, int size, int max_bits) +{ + int k, written_bits = 0; + + for (k = 0; k < size; k++) { + written_bits += hweight8(~buff[k]); + if (written_bits > max_bits) + break; + } + + return written_bits; +} + +static void dma_complete(void *param) +{ + struct fsmc_nand_data *host = param; + + complete(&host->dma_access_complete); +} + +static int dma_xfer(struct fsmc_nand_data *host, void *buffer, int len, + enum dma_data_direction direction) +{ + struct dma_chan *chan; + struct dma_device *dma_dev; + struct dma_async_tx_descriptor *tx; + dma_addr_t dma_dst, dma_src, dma_addr; + dma_cookie_t cookie; + unsigned long flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; + int ret; + + if (direction == DMA_TO_DEVICE) + chan = host->write_dma_chan; + else if (direction == DMA_FROM_DEVICE) + chan = host->read_dma_chan; + else + return -EINVAL; + + dma_dev = chan->device; + dma_addr = dma_map_single(dma_dev->dev, buffer, len, direction); + + if (direction == DMA_TO_DEVICE) { + dma_src = dma_addr; + dma_dst = host->data_pa; + } else { + dma_src = host->data_pa; + dma_dst = dma_addr; + } + + tx = dma_dev->device_prep_dma_memcpy(chan, dma_dst, dma_src, + len, flags); + if (!tx) { + dev_err(host->dev, "device_prep_dma_memcpy error\n"); + ret = -EIO; + goto unmap_dma; + } + + tx->callback = dma_complete; + tx->callback_param = host; + cookie = tx->tx_submit(tx); + + ret = dma_submit_error(cookie); + if (ret) { + dev_err(host->dev, "dma_submit_error %d\n", cookie); + goto unmap_dma; + } + + dma_async_issue_pending(chan); + + ret = + wait_for_completion_timeout(&host->dma_access_complete, + msecs_to_jiffies(3000)); + if (ret <= 0) { + dmaengine_terminate_all(chan); + dev_err(host->dev, "wait_for_completion_timeout\n"); + if (!ret) + ret = -ETIMEDOUT; + goto unmap_dma; + } + + ret = 0; + +unmap_dma: + dma_unmap_single(dma_dev->dev, dma_addr, len, direction); + + return ret; +} + +/* + * fsmc_write_buf - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void fsmc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + int i; + struct nand_chip *chip = mtd->priv; + + if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) && + IS_ALIGNED(len, sizeof(uint32_t))) { + uint32_t *p = (uint32_t *)buf; + len = len >> 2; + for (i = 0; i < len; i++) + writel_relaxed(p[i], chip->IO_ADDR_W); + } else { + for (i = 0; i < len; i++) + writeb_relaxed(buf[i], chip->IO_ADDR_W); + } +} + +/* + * fsmc_read_buf - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void fsmc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + int i; + struct nand_chip *chip = mtd->priv; + + if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) && + IS_ALIGNED(len, sizeof(uint32_t))) { + uint32_t *p = (uint32_t *)buf; + len = len >> 2; + for (i = 0; i < len; i++) + p[i] = readl_relaxed(chip->IO_ADDR_R); + } else { + for (i = 0; i < len; i++) + buf[i] = readb_relaxed(chip->IO_ADDR_R); + } +} + +/* + * fsmc_read_buf_dma - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void fsmc_read_buf_dma(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct fsmc_nand_data *host; + + host = container_of(mtd, struct fsmc_nand_data, mtd); + dma_xfer(host, buf, len, DMA_FROM_DEVICE); +} + +/* + * fsmc_write_buf_dma - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void fsmc_write_buf_dma(struct mtd_info *mtd, const uint8_t *buf, + int len) +{ + struct fsmc_nand_data *host; + + host = container_of(mtd, struct fsmc_nand_data, mtd); + dma_xfer(host, (void *)buf, len, DMA_TO_DEVICE); +} + +/* + * fsmc_read_page_hwecc + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller expects OOB data read to chip->oob_poi + * @page: page number to read + * + * This routine is needed for fsmc version 8 as reading from NAND chip has to be + * performed in a strict sequence as follows: + * data(512 byte) -> ecc(13 byte) + * After this read, fsmc hardware generates and reports error data bits(up to a + * max of 8 bits) + */ +static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + struct fsmc_eccplace *ecc_place = host->ecc_place; + int i, j, s, stat, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + int off, len, group = 0; + /* + * ecc_oob is intentionally taken as uint16_t. In 16bit devices, we + * end up reading 14 bytes (7 words) from oob. The local array is + * to maintain word alignment + */ + uint16_t ecc_oob[7]; + uint8_t *oob = (uint8_t *)&ecc_oob[0]; + unsigned int max_bitflips = 0; + + for (i = 0, s = 0; s < eccsteps; s++, i += eccbytes, p += eccsize) { + chip->cmdfunc(mtd, NAND_CMD_READ0, s * eccsize, page); + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + + for (j = 0; j < eccbytes;) { + off = ecc_place->eccplace[group].offset; + len = ecc_place->eccplace[group].length; + group++; + + /* + * length is intentionally kept a higher multiple of 2 + * to read at least 13 bytes even in case of 16 bit NAND + * devices + */ + if (chip->options & NAND_BUSWIDTH_16) + len = roundup(len, 2); + + chip->cmdfunc(mtd, NAND_CMD_READOOB, off, page); + chip->read_buf(mtd, oob + j, len); + j += len; + } + + memcpy(&ecc_code[i], oob, chip->ecc.bytes); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + + stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + } + + return max_bitflips; +} + +/* + * fsmc_bch8_correct_data + * @mtd: mtd info structure + * @dat: buffer of read data + * @read_ecc: ecc read from device spare area + * @calc_ecc: ecc calculated from read data + * + * calc_ecc is a 104 bit information containing maximum of 8 error + * offset informations of 13 bits each in 512 bytes of read data. + */ +static int fsmc_bch8_correct_data(struct mtd_info *mtd, uint8_t *dat, + uint8_t *read_ecc, uint8_t *calc_ecc) +{ + struct fsmc_nand_data *host = container_of(mtd, + struct fsmc_nand_data, mtd); + struct nand_chip *chip = mtd->priv; + void __iomem *regs = host->regs_va; + unsigned int bank = host->bank; + uint32_t err_idx[8]; + uint32_t num_err, i; + uint32_t ecc1, ecc2, ecc3, ecc4; + + num_err = (readl_relaxed(FSMC_NAND_REG(regs, bank, STS)) >> 10) & 0xF; + + /* no bit flipping */ + if (likely(num_err == 0)) + return 0; + + /* too many errors */ + if (unlikely(num_err > 8)) { + /* + * This is a temporary erase check. A newly erased page read + * would result in an ecc error because the oob data is also + * erased to FF and the calculated ecc for an FF data is not + * FF..FF. + * This is a workaround to skip performing correction in case + * data is FF..FF + * + * Logic: + * For every page, each bit written as 0 is counted until these + * number of bits are greater than 8 (the maximum correction + * capability of FSMC for each 512 + 13 bytes) + */ + + int bits_ecc = count_written_bits(read_ecc, chip->ecc.bytes, 8); + int bits_data = count_written_bits(dat, chip->ecc.size, 8); + + if ((bits_ecc + bits_data) <= 8) { + if (bits_data) + memset(dat, 0xff, chip->ecc.size); + return bits_data; + } + + return -EBADMSG; + } + + /* + * ------------------- calc_ecc[] bit wise -----------|--13 bits--| + * |---idx[7]--|--.....-----|---idx[2]--||---idx[1]--||---idx[0]--| + * + * calc_ecc is a 104 bit information containing maximum of 8 error + * offset informations of 13 bits each. calc_ecc is copied into a + * uint64_t array and error offset indexes are populated in err_idx + * array + */ + ecc1 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1)); + ecc2 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC2)); + ecc3 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC3)); + ecc4 = readl_relaxed(FSMC_NAND_REG(regs, bank, STS)); + + err_idx[0] = (ecc1 >> 0) & 0x1FFF; + err_idx[1] = (ecc1 >> 13) & 0x1FFF; + err_idx[2] = (((ecc2 >> 0) & 0x7F) << 6) | ((ecc1 >> 26) & 0x3F); + err_idx[3] = (ecc2 >> 7) & 0x1FFF; + err_idx[4] = (((ecc3 >> 0) & 0x1) << 12) | ((ecc2 >> 20) & 0xFFF); + err_idx[5] = (ecc3 >> 1) & 0x1FFF; + err_idx[6] = (ecc3 >> 14) & 0x1FFF; + err_idx[7] = (((ecc4 >> 16) & 0xFF) << 5) | ((ecc3 >> 27) & 0x1F); + + i = 0; + while (num_err--) { + change_bit(0, (unsigned long *)&err_idx[i]); + change_bit(1, (unsigned long *)&err_idx[i]); + + if (err_idx[i] < chip->ecc.size * 8) { + change_bit(err_idx[i], (unsigned long *)dat); + i++; + } + } + return i; +} + +static bool filter(struct dma_chan *chan, void *slave) +{ + chan->private = slave; + return true; +} + +#ifdef CONFIG_OF +static int fsmc_nand_probe_config_dt(struct platform_device *pdev, + struct device_node *np) +{ + struct fsmc_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + u32 val; + int ret; + + /* Set default NAND width to 8 bits */ + pdata->width = 8; + if (!of_property_read_u32(np, "bank-width", &val)) { + if (val == 2) { + pdata->width = 16; + } else if (val != 1) { + dev_err(&pdev->dev, "invalid bank-width %u\n", val); + return -EINVAL; + } + } + if (of_get_property(np, "nand-skip-bbtscan", NULL)) + pdata->options = NAND_SKIP_BBTSCAN; + + pdata->nand_timings = devm_kzalloc(&pdev->dev, + sizeof(*pdata->nand_timings), GFP_KERNEL); + if (!pdata->nand_timings) + return -ENOMEM; + ret = of_property_read_u8_array(np, "timings", (u8 *)pdata->nand_timings, + sizeof(*pdata->nand_timings)); + if (ret) { + dev_info(&pdev->dev, "No timings in dts specified, using default timings!\n"); + pdata->nand_timings = NULL; + } + + /* Set default NAND bank to 0 */ + pdata->bank = 0; + if (!of_property_read_u32(np, "bank", &val)) { + if (val > 3) { + dev_err(&pdev->dev, "invalid bank %u\n", val); + return -EINVAL; + } + pdata->bank = val; + } + return 0; +} +#else +static int fsmc_nand_probe_config_dt(struct platform_device *pdev, + struct device_node *np) +{ + return -ENOSYS; +} +#endif + +/* + * fsmc_nand_probe - Probe function + * @pdev: platform device structure + */ +static int __init fsmc_nand_probe(struct platform_device *pdev) +{ + struct fsmc_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + struct device_node __maybe_unused *np = pdev->dev.of_node; + struct mtd_part_parser_data ppdata = {}; + struct fsmc_nand_data *host; + struct mtd_info *mtd; + struct nand_chip *nand; + struct resource *res; + dma_cap_mask_t mask; + int ret = 0; + u32 pid; + int i; + + if (np) { + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + pdev->dev.platform_data = pdata; + ret = fsmc_nand_probe_config_dt(pdev, np); + if (ret) { + dev_err(&pdev->dev, "no platform data\n"); + return -ENODEV; + } + } + + if (!pdata) { + dev_err(&pdev->dev, "platform data is NULL\n"); + return -EINVAL; + } + + /* Allocate memory for the device structure (and zero it) */ + host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_data"); + host->data_va = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->data_va)) + return PTR_ERR(host->data_va); + + host->data_pa = (dma_addr_t)res->start; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_addr"); + host->addr_va = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->addr_va)) + return PTR_ERR(host->addr_va); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_cmd"); + host->cmd_va = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->cmd_va)) + return PTR_ERR(host->cmd_va); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fsmc_regs"); + host->regs_va = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->regs_va)) + return PTR_ERR(host->regs_va); + + host->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(host->clk)) { + dev_err(&pdev->dev, "failed to fetch block clock\n"); + return PTR_ERR(host->clk); + } + + ret = clk_prepare_enable(host->clk); + if (ret) + goto err_clk_prepare_enable; + + /* + * This device ID is actually a common AMBA ID as used on the + * AMBA PrimeCell bus. However it is not a PrimeCell. + */ + for (pid = 0, i = 0; i < 4; i++) + pid |= (readl(host->regs_va + resource_size(res) - 0x20 + 4 * i) & 255) << (i * 8); + host->pid = pid; + dev_info(&pdev->dev, "FSMC device partno %03x, manufacturer %02x, " + "revision %02x, config %02x\n", + AMBA_PART_BITS(pid), AMBA_MANF_BITS(pid), + AMBA_REV_BITS(pid), AMBA_CONFIG_BITS(pid)); + + host->bank = pdata->bank; + host->select_chip = pdata->select_bank; + host->partitions = pdata->partitions; + host->nr_partitions = pdata->nr_partitions; + host->dev = &pdev->dev; + host->dev_timings = pdata->nand_timings; + host->mode = pdata->mode; + + if (host->mode == USE_DMA_ACCESS) + init_completion(&host->dma_access_complete); + + /* Link all private pointers */ + mtd = &host->mtd; + nand = &host->nand; + mtd->priv = nand; + nand->priv = host; + + host->mtd.owner = THIS_MODULE; + nand->IO_ADDR_R = host->data_va; + nand->IO_ADDR_W = host->data_va; + nand->cmd_ctrl = fsmc_cmd_ctrl; + nand->chip_delay = 30; + + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.hwctl = fsmc_enable_hwecc; + nand->ecc.size = 512; + nand->options = pdata->options; + nand->select_chip = fsmc_select_chip; + nand->badblockbits = 7; + + if (pdata->width == FSMC_NAND_BW16) + nand->options |= NAND_BUSWIDTH_16; + + switch (host->mode) { + case USE_DMA_ACCESS: + dma_cap_zero(mask); + dma_cap_set(DMA_MEMCPY, mask); + host->read_dma_chan = dma_request_channel(mask, filter, + pdata->read_dma_priv); + if (!host->read_dma_chan) { + dev_err(&pdev->dev, "Unable to get read dma channel\n"); + goto err_req_read_chnl; + } + host->write_dma_chan = dma_request_channel(mask, filter, + pdata->write_dma_priv); + if (!host->write_dma_chan) { + dev_err(&pdev->dev, "Unable to get write dma channel\n"); + goto err_req_write_chnl; + } + nand->read_buf = fsmc_read_buf_dma; + nand->write_buf = fsmc_write_buf_dma; + break; + + default: + case USE_WORD_ACCESS: + nand->read_buf = fsmc_read_buf; + nand->write_buf = fsmc_write_buf; + break; + } + + fsmc_nand_setup(host->regs_va, host->bank, + nand->options & NAND_BUSWIDTH_16, + host->dev_timings); + + if (AMBA_REV_BITS(host->pid) >= 8) { + nand->ecc.read_page = fsmc_read_page_hwecc; + nand->ecc.calculate = fsmc_read_hwecc_ecc4; + nand->ecc.correct = fsmc_bch8_correct_data; + nand->ecc.bytes = 13; + nand->ecc.strength = 8; + } else { + nand->ecc.calculate = fsmc_read_hwecc_ecc1; + nand->ecc.correct = nand_correct_data; + nand->ecc.bytes = 3; + nand->ecc.strength = 1; + } + + /* + * Scan to find existence of the device + */ + if (nand_scan_ident(&host->mtd, 1, NULL)) { + ret = -ENXIO; + dev_err(&pdev->dev, "No NAND Device found!\n"); + goto err_scan_ident; + } + + if (AMBA_REV_BITS(host->pid) >= 8) { + switch (host->mtd.oobsize) { + case 16: + nand->ecc.layout = &fsmc_ecc4_16_layout; + host->ecc_place = &fsmc_ecc4_sp_place; + break; + case 64: + nand->ecc.layout = &fsmc_ecc4_64_layout; + host->ecc_place = &fsmc_ecc4_lp_place; + break; + case 128: + nand->ecc.layout = &fsmc_ecc4_128_layout; + host->ecc_place = &fsmc_ecc4_lp_place; + break; + case 224: + nand->ecc.layout = &fsmc_ecc4_224_layout; + host->ecc_place = &fsmc_ecc4_lp_place; + break; + case 256: + nand->ecc.layout = &fsmc_ecc4_256_layout; + host->ecc_place = &fsmc_ecc4_lp_place; + break; + default: + dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n", + mtd->oobsize); + BUG(); + } + } else { + switch (host->mtd.oobsize) { + case 16: + nand->ecc.layout = &fsmc_ecc1_16_layout; + break; + case 64: + nand->ecc.layout = &fsmc_ecc1_64_layout; + break; + case 128: + nand->ecc.layout = &fsmc_ecc1_128_layout; + break; + default: + dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n", + mtd->oobsize); + BUG(); + } + } + + /* Second stage of scan to fill MTD data-structures */ + if (nand_scan_tail(&host->mtd)) { + ret = -ENXIO; + goto err_probe; + } + + /* + * The partition information can is accessed by (in the same precedence) + * + * command line through Bootloader, + * platform data, + * default partition information present in driver. + */ + /* + * Check for partition info passed + */ + host->mtd.name = "nand"; + ppdata.of_node = np; + ret = mtd_device_parse_register(&host->mtd, NULL, &ppdata, + host->partitions, host->nr_partitions); + if (ret) + goto err_probe; + + platform_set_drvdata(pdev, host); + dev_info(&pdev->dev, "FSMC NAND driver registration successful\n"); + return 0; + +err_probe: +err_scan_ident: + if (host->mode == USE_DMA_ACCESS) + dma_release_channel(host->write_dma_chan); +err_req_write_chnl: + if (host->mode == USE_DMA_ACCESS) + dma_release_channel(host->read_dma_chan); +err_req_read_chnl: + clk_disable_unprepare(host->clk); +err_clk_prepare_enable: + clk_put(host->clk); + return ret; +} + +/* + * Clean up routine + */ +static int fsmc_nand_remove(struct platform_device *pdev) +{ + struct fsmc_nand_data *host = platform_get_drvdata(pdev); + + if (host) { + nand_release(&host->mtd); + + if (host->mode == USE_DMA_ACCESS) { + dma_release_channel(host->write_dma_chan); + dma_release_channel(host->read_dma_chan); + } + clk_disable_unprepare(host->clk); + clk_put(host->clk); + } + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int fsmc_nand_suspend(struct device *dev) +{ + struct fsmc_nand_data *host = dev_get_drvdata(dev); + if (host) + clk_disable_unprepare(host->clk); + return 0; +} + +static int fsmc_nand_resume(struct device *dev) +{ + struct fsmc_nand_data *host = dev_get_drvdata(dev); + if (host) { + clk_prepare_enable(host->clk); + fsmc_nand_setup(host->regs_va, host->bank, + host->nand.options & NAND_BUSWIDTH_16, + host->dev_timings); + } + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(fsmc_nand_pm_ops, fsmc_nand_suspend, fsmc_nand_resume); + +#ifdef CONFIG_OF +static const struct of_device_id fsmc_nand_id_table[] = { + { .compatible = "st,spear600-fsmc-nand" }, + { .compatible = "stericsson,fsmc-nand" }, + {} +}; +MODULE_DEVICE_TABLE(of, fsmc_nand_id_table); +#endif + +static struct platform_driver fsmc_nand_driver = { + .remove = fsmc_nand_remove, + .driver = { + .name = "fsmc-nand", + .of_match_table = of_match_ptr(fsmc_nand_id_table), + .pm = &fsmc_nand_pm_ops, + }, +}; + +module_platform_driver_probe(fsmc_nand_driver, fsmc_nand_probe); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Vipin Kumar <vipin.kumar@st.com>, Ashish Priyadarshi"); +MODULE_DESCRIPTION("NAND driver for SPEAr Platforms"); diff --git a/drivers/mtd/nand/gpio.c b/drivers/mtd/nand/gpio.c new file mode 100644 index 000000000..73c4048c3 --- /dev/null +++ b/drivers/mtd/nand/gpio.c @@ -0,0 +1,321 @@ +/* + * drivers/mtd/nand/gpio.c + * + * Updated, and converted to generic GPIO based driver by Russell King. + * + * Written by Ben Dooks <ben@simtec.co.uk> + * Based on 2.4 version by Mark Whittaker + * + * © 2004 Simtec Electronics + * + * Device driver for NAND flash that uses a memory mapped interface to + * read/write the NAND commands and data, and GPIO pins for control signals + * (the DT binding refers to this as "GPIO assisted NAND flash") + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/kernel.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/nand-gpio.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_gpio.h> + +struct gpiomtd { + void __iomem *io_sync; + struct mtd_info mtd_info; + struct nand_chip nand_chip; + struct gpio_nand_platdata plat; +}; + +#define gpio_nand_getpriv(x) container_of(x, struct gpiomtd, mtd_info) + + +#ifdef CONFIG_ARM +/* gpio_nand_dosync() + * + * Make sure the GPIO state changes occur in-order with writes to NAND + * memory region. + * Needed on PXA due to bus-reordering within the SoC itself (see section on + * I/O ordering in PXA manual (section 2.3, p35) + */ +static void gpio_nand_dosync(struct gpiomtd *gpiomtd) +{ + unsigned long tmp; + + if (gpiomtd->io_sync) { + /* + * Linux memory barriers don't cater for what's required here. + * What's required is what's here - a read from a separate + * region with a dependency on that read. + */ + tmp = readl(gpiomtd->io_sync); + asm volatile("mov %1, %0\n" : "=r" (tmp) : "r" (tmp)); + } +} +#else +static inline void gpio_nand_dosync(struct gpiomtd *gpiomtd) {} +#endif + +static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); + + gpio_nand_dosync(gpiomtd); + + if (ctrl & NAND_CTRL_CHANGE) { + gpio_set_value(gpiomtd->plat.gpio_nce, !(ctrl & NAND_NCE)); + gpio_set_value(gpiomtd->plat.gpio_cle, !!(ctrl & NAND_CLE)); + gpio_set_value(gpiomtd->plat.gpio_ale, !!(ctrl & NAND_ALE)); + gpio_nand_dosync(gpiomtd); + } + if (cmd == NAND_CMD_NONE) + return; + + writeb(cmd, gpiomtd->nand_chip.IO_ADDR_W); + gpio_nand_dosync(gpiomtd); +} + +static int gpio_nand_devready(struct mtd_info *mtd) +{ + struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); + + return gpio_get_value(gpiomtd->plat.gpio_rdy); +} + +#ifdef CONFIG_OF +static const struct of_device_id gpio_nand_id_table[] = { + { .compatible = "gpio-control-nand" }, + {} +}; +MODULE_DEVICE_TABLE(of, gpio_nand_id_table); + +static int gpio_nand_get_config_of(const struct device *dev, + struct gpio_nand_platdata *plat) +{ + u32 val; + + if (!dev->of_node) + return -ENODEV; + + if (!of_property_read_u32(dev->of_node, "bank-width", &val)) { + if (val == 2) { + plat->options |= NAND_BUSWIDTH_16; + } else if (val != 1) { + dev_err(dev, "invalid bank-width %u\n", val); + return -EINVAL; + } + } + + plat->gpio_rdy = of_get_gpio(dev->of_node, 0); + plat->gpio_nce = of_get_gpio(dev->of_node, 1); + plat->gpio_ale = of_get_gpio(dev->of_node, 2); + plat->gpio_cle = of_get_gpio(dev->of_node, 3); + plat->gpio_nwp = of_get_gpio(dev->of_node, 4); + + if (!of_property_read_u32(dev->of_node, "chip-delay", &val)) + plat->chip_delay = val; + + return 0; +} + +static struct resource *gpio_nand_get_io_sync_of(struct platform_device *pdev) +{ + struct resource *r; + u64 addr; + + if (of_property_read_u64(pdev->dev.of_node, + "gpio-control-nand,io-sync-reg", &addr)) + return NULL; + + r = devm_kzalloc(&pdev->dev, sizeof(*r), GFP_KERNEL); + if (!r) + return NULL; + + r->start = addr; + r->end = r->start + 0x3; + r->flags = IORESOURCE_MEM; + + return r; +} +#else /* CONFIG_OF */ +static inline int gpio_nand_get_config_of(const struct device *dev, + struct gpio_nand_platdata *plat) +{ + return -ENOSYS; +} + +static inline struct resource * +gpio_nand_get_io_sync_of(struct platform_device *pdev) +{ + return NULL; +} +#endif /* CONFIG_OF */ + +static inline int gpio_nand_get_config(const struct device *dev, + struct gpio_nand_platdata *plat) +{ + int ret = gpio_nand_get_config_of(dev, plat); + + if (!ret) + return ret; + + if (dev_get_platdata(dev)) { + memcpy(plat, dev_get_platdata(dev), sizeof(*plat)); + return 0; + } + + return -EINVAL; +} + +static inline struct resource * +gpio_nand_get_io_sync(struct platform_device *pdev) +{ + struct resource *r = gpio_nand_get_io_sync_of(pdev); + + if (r) + return r; + + return platform_get_resource(pdev, IORESOURCE_MEM, 1); +} + +static int gpio_nand_remove(struct platform_device *pdev) +{ + struct gpiomtd *gpiomtd = platform_get_drvdata(pdev); + + nand_release(&gpiomtd->mtd_info); + + if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) + gpio_set_value(gpiomtd->plat.gpio_nwp, 0); + gpio_set_value(gpiomtd->plat.gpio_nce, 1); + + return 0; +} + +static int gpio_nand_probe(struct platform_device *pdev) +{ + struct gpiomtd *gpiomtd; + struct nand_chip *chip; + struct resource *res; + struct mtd_part_parser_data ppdata = {}; + int ret = 0; + + if (!pdev->dev.of_node && !dev_get_platdata(&pdev->dev)) + return -EINVAL; + + gpiomtd = devm_kzalloc(&pdev->dev, sizeof(*gpiomtd), GFP_KERNEL); + if (!gpiomtd) + return -ENOMEM; + + chip = &gpiomtd->nand_chip; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(chip->IO_ADDR_R)) + return PTR_ERR(chip->IO_ADDR_R); + + res = gpio_nand_get_io_sync(pdev); + if (res) { + gpiomtd->io_sync = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(gpiomtd->io_sync)) + return PTR_ERR(gpiomtd->io_sync); + } + + ret = gpio_nand_get_config(&pdev->dev, &gpiomtd->plat); + if (ret) + return ret; + + ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nce, "NAND NCE"); + if (ret) + return ret; + gpio_direction_output(gpiomtd->plat.gpio_nce, 1); + + if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) { + ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp, + "NAND NWP"); + if (ret) + return ret; + } + + ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_ale, "NAND ALE"); + if (ret) + return ret; + gpio_direction_output(gpiomtd->plat.gpio_ale, 0); + + ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_cle, "NAND CLE"); + if (ret) + return ret; + gpio_direction_output(gpiomtd->plat.gpio_cle, 0); + + if (gpio_is_valid(gpiomtd->plat.gpio_rdy)) { + ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_rdy, + "NAND RDY"); + if (ret) + return ret; + gpio_direction_input(gpiomtd->plat.gpio_rdy); + chip->dev_ready = gpio_nand_devready; + } + + chip->IO_ADDR_W = chip->IO_ADDR_R; + chip->ecc.mode = NAND_ECC_SOFT; + chip->options = gpiomtd->plat.options; + chip->chip_delay = gpiomtd->plat.chip_delay; + chip->cmd_ctrl = gpio_nand_cmd_ctrl; + + gpiomtd->mtd_info.priv = chip; + gpiomtd->mtd_info.owner = THIS_MODULE; + + platform_set_drvdata(pdev, gpiomtd); + + if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) + gpio_direction_output(gpiomtd->plat.gpio_nwp, 1); + + if (nand_scan(&gpiomtd->mtd_info, 1)) { + ret = -ENXIO; + goto err_wp; + } + + if (gpiomtd->plat.adjust_parts) + gpiomtd->plat.adjust_parts(&gpiomtd->plat, + gpiomtd->mtd_info.size); + + ppdata.of_node = pdev->dev.of_node; + ret = mtd_device_parse_register(&gpiomtd->mtd_info, NULL, &ppdata, + gpiomtd->plat.parts, + gpiomtd->plat.num_parts); + if (!ret) + return 0; + +err_wp: + if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) + gpio_set_value(gpiomtd->plat.gpio_nwp, 0); + + return ret; +} + +static struct platform_driver gpio_nand_driver = { + .probe = gpio_nand_probe, + .remove = gpio_nand_remove, + .driver = { + .name = "gpio-nand", + .of_match_table = of_match_ptr(gpio_nand_id_table), + }, +}; + +module_platform_driver(gpio_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_DESCRIPTION("GPIO NAND Driver"); diff --git a/drivers/mtd/nand/gpmi-nand/Makefile b/drivers/mtd/nand/gpmi-nand/Makefile new file mode 100644 index 000000000..3a462487c --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/Makefile @@ -0,0 +1,3 @@ +obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi_nand.o +gpmi_nand-objs += gpmi-nand.o +gpmi_nand-objs += gpmi-lib.o diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h new file mode 100644 index 000000000..05bb91f2f --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h @@ -0,0 +1,128 @@ +/* + * Freescale GPMI NAND Flash Driver + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008 Embedded Alley Solutions, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#ifndef __GPMI_NAND_BCH_REGS_H +#define __GPMI_NAND_BCH_REGS_H + +#define HW_BCH_CTRL 0x00000000 +#define HW_BCH_CTRL_SET 0x00000004 +#define HW_BCH_CTRL_CLR 0x00000008 +#define HW_BCH_CTRL_TOG 0x0000000c + +#define BM_BCH_CTRL_COMPLETE_IRQ_EN (1 << 8) +#define BM_BCH_CTRL_COMPLETE_IRQ (1 << 0) + +#define HW_BCH_STATUS0 0x00000010 +#define HW_BCH_MODE 0x00000020 +#define HW_BCH_ENCODEPTR 0x00000030 +#define HW_BCH_DATAPTR 0x00000040 +#define HW_BCH_METAPTR 0x00000050 +#define HW_BCH_LAYOUTSELECT 0x00000070 + +#define HW_BCH_FLASH0LAYOUT0 0x00000080 + +#define BP_BCH_FLASH0LAYOUT0_NBLOCKS 24 +#define BM_BCH_FLASH0LAYOUT0_NBLOCKS (0xff << BP_BCH_FLASH0LAYOUT0_NBLOCKS) +#define BF_BCH_FLASH0LAYOUT0_NBLOCKS(v) \ + (((v) << BP_BCH_FLASH0LAYOUT0_NBLOCKS) & BM_BCH_FLASH0LAYOUT0_NBLOCKS) + +#define BP_BCH_FLASH0LAYOUT0_META_SIZE 16 +#define BM_BCH_FLASH0LAYOUT0_META_SIZE (0xff << BP_BCH_FLASH0LAYOUT0_META_SIZE) +#define BF_BCH_FLASH0LAYOUT0_META_SIZE(v) \ + (((v) << BP_BCH_FLASH0LAYOUT0_META_SIZE)\ + & BM_BCH_FLASH0LAYOUT0_META_SIZE) + +#define BP_BCH_FLASH0LAYOUT0_ECC0 12 +#define BM_BCH_FLASH0LAYOUT0_ECC0 (0xf << BP_BCH_FLASH0LAYOUT0_ECC0) +#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0 11 +#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0 (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) +#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x) \ + (GPMI_IS_MX6(x) \ + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) \ + & MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0) \ + : (((v) << BP_BCH_FLASH0LAYOUT0_ECC0) \ + & BM_BCH_FLASH0LAYOUT0_ECC0) \ + ) + +#define MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14 10 +#define MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14 \ + (0x1 << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14) +#define BF_BCH_FLASH0LAYOUT0_GF(v, x) \ + ((GPMI_IS_MX6(x) && ((v) == 14)) \ + ? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14) \ + & MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14) \ + : 0 \ + ) + +#define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE 0 +#define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ + (0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) +#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ + (0x3ff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) +#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x) \ + (GPMI_IS_MX6(x) \ + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ + : ((v) & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ + ) + +#define HW_BCH_FLASH0LAYOUT1 0x00000090 + +#define BP_BCH_FLASH0LAYOUT1_PAGE_SIZE 16 +#define BM_BCH_FLASH0LAYOUT1_PAGE_SIZE \ + (0xffff << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE) +#define BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(v) \ + (((v) << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE) \ + & BM_BCH_FLASH0LAYOUT1_PAGE_SIZE) + +#define BP_BCH_FLASH0LAYOUT1_ECCN 12 +#define BM_BCH_FLASH0LAYOUT1_ECCN (0xf << BP_BCH_FLASH0LAYOUT1_ECCN) +#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN 11 +#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) +#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x) \ + (GPMI_IS_MX6(x) \ + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) \ + & MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN) \ + : (((v) << BP_BCH_FLASH0LAYOUT1_ECCN) \ + & BM_BCH_FLASH0LAYOUT1_ECCN) \ + ) + +#define MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14 10 +#define MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14 \ + (0x1 << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14) +#define BF_BCH_FLASH0LAYOUT1_GF(v, x) \ + ((GPMI_IS_MX6(x) && ((v) == 14)) \ + ? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14) \ + & MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14) \ + : 0 \ + ) + +#define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE 0 +#define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ + (0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) +#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ + (0x3ff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) +#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x) \ + (GPMI_IS_MX6(x) \ + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ + : ((v) & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ + ) + +#define HW_BCH_VERSION 0x00000160 +#endif diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c new file mode 100644 index 000000000..43fa16b5f --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -0,0 +1,1508 @@ +/* + * Freescale GPMI NAND Flash Driver + * + * Copyright (C) 2008-2011 Freescale Semiconductor, Inc. + * Copyright (C) 2008 Embedded Alley Solutions, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/slab.h> + +#include "gpmi-nand.h" +#include "gpmi-regs.h" +#include "bch-regs.h" + +static struct timing_threshod timing_default_threshold = { + .max_data_setup_cycles = (BM_GPMI_TIMING0_DATA_SETUP >> + BP_GPMI_TIMING0_DATA_SETUP), + .internal_data_setup_in_ns = 0, + .max_sample_delay_factor = (BM_GPMI_CTRL1_RDN_DELAY >> + BP_GPMI_CTRL1_RDN_DELAY), + .max_dll_clock_period_in_ns = 32, + .max_dll_delay_in_ns = 16, +}; + +#define MXS_SET_ADDR 0x4 +#define MXS_CLR_ADDR 0x8 +/* + * Clear the bit and poll it cleared. This is usually called with + * a reset address and mask being either SFTRST(bit 31) or CLKGATE + * (bit 30). + */ +static int clear_poll_bit(void __iomem *addr, u32 mask) +{ + int timeout = 0x400; + + /* clear the bit */ + writel(mask, addr + MXS_CLR_ADDR); + + /* + * SFTRST needs 3 GPMI clocks to settle, the reference manual + * recommends to wait 1us. + */ + udelay(1); + + /* poll the bit becoming clear */ + while ((readl(addr) & mask) && --timeout) + /* nothing */; + + return !timeout; +} + +#define MODULE_CLKGATE (1 << 30) +#define MODULE_SFTRST (1 << 31) +/* + * The current mxs_reset_block() will do two things: + * [1] enable the module. + * [2] reset the module. + * + * In most of the cases, it's ok. + * But in MX23, there is a hardware bug in the BCH block (see erratum #2847). + * If you try to soft reset the BCH block, it becomes unusable until + * the next hard reset. This case occurs in the NAND boot mode. When the board + * boots by NAND, the ROM of the chip will initialize the BCH blocks itself. + * So If the driver tries to reset the BCH again, the BCH will not work anymore. + * You will see a DMA timeout in this case. The bug has been fixed + * in the following chips, such as MX28. + * + * To avoid this bug, just add a new parameter `just_enable` for + * the mxs_reset_block(), and rewrite it here. + */ +static int gpmi_reset_block(void __iomem *reset_addr, bool just_enable) +{ + int ret; + int timeout = 0x400; + + /* clear and poll SFTRST */ + ret = clear_poll_bit(reset_addr, MODULE_SFTRST); + if (unlikely(ret)) + goto error; + + /* clear CLKGATE */ + writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR); + + if (!just_enable) { + /* set SFTRST to reset the block */ + writel(MODULE_SFTRST, reset_addr + MXS_SET_ADDR); + udelay(1); + + /* poll CLKGATE becoming set */ + while ((!(readl(reset_addr) & MODULE_CLKGATE)) && --timeout) + /* nothing */; + if (unlikely(!timeout)) + goto error; + } + + /* clear and poll SFTRST */ + ret = clear_poll_bit(reset_addr, MODULE_SFTRST); + if (unlikely(ret)) + goto error; + + /* clear and poll CLKGATE */ + ret = clear_poll_bit(reset_addr, MODULE_CLKGATE); + if (unlikely(ret)) + goto error; + + return 0; + +error: + pr_err("%s(%p): module reset timeout\n", __func__, reset_addr); + return -ETIMEDOUT; +} + +static int __gpmi_enable_clk(struct gpmi_nand_data *this, bool v) +{ + struct clk *clk; + int ret; + int i; + + for (i = 0; i < GPMI_CLK_MAX; i++) { + clk = this->resources.clock[i]; + if (!clk) + break; + + if (v) { + ret = clk_prepare_enable(clk); + if (ret) + goto err_clk; + } else { + clk_disable_unprepare(clk); + } + } + return 0; + +err_clk: + for (; i > 0; i--) + clk_disable_unprepare(this->resources.clock[i - 1]); + return ret; +} + +#define gpmi_enable_clk(x) __gpmi_enable_clk(x, true) +#define gpmi_disable_clk(x) __gpmi_enable_clk(x, false) + +int gpmi_init(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + int ret; + + ret = gpmi_enable_clk(this); + if (ret) + goto err_out; + ret = gpmi_reset_block(r->gpmi_regs, false); + if (ret) + goto err_out; + + /* + * Reset BCH here, too. We got failures otherwise :( + * See later BCH reset for explanation of MX23 handling + */ + ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); + if (ret) + goto err_out; + + + /* Choose NAND mode. */ + writel(BM_GPMI_CTRL1_GPMI_MODE, r->gpmi_regs + HW_GPMI_CTRL1_CLR); + + /* Set the IRQ polarity. */ + writel(BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY, + r->gpmi_regs + HW_GPMI_CTRL1_SET); + + /* Disable Write-Protection. */ + writel(BM_GPMI_CTRL1_DEV_RESET, r->gpmi_regs + HW_GPMI_CTRL1_SET); + + /* Select BCH ECC. */ + writel(BM_GPMI_CTRL1_BCH_MODE, r->gpmi_regs + HW_GPMI_CTRL1_SET); + + /* + * Decouple the chip select from dma channel. We use dma0 for all + * the chips. + */ + writel(BM_GPMI_CTRL1_DECOUPLE_CS, r->gpmi_regs + HW_GPMI_CTRL1_SET); + + gpmi_disable_clk(this); + return 0; +err_out: + return ret; +} + +/* This function is very useful. It is called only when the bug occur. */ +void gpmi_dump_info(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + struct bch_geometry *geo = &this->bch_geometry; + u32 reg; + int i; + + dev_err(this->dev, "Show GPMI registers :\n"); + for (i = 0; i <= HW_GPMI_DEBUG / 0x10 + 1; i++) { + reg = readl(r->gpmi_regs + i * 0x10); + dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); + } + + /* start to print out the BCH info */ + dev_err(this->dev, "Show BCH registers :\n"); + for (i = 0; i <= HW_BCH_VERSION / 0x10 + 1; i++) { + reg = readl(r->bch_regs + i * 0x10); + dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); + } + dev_err(this->dev, "BCH Geometry :\n" + "GF length : %u\n" + "ECC Strength : %u\n" + "Page Size in Bytes : %u\n" + "Metadata Size in Bytes : %u\n" + "ECC Chunk Size in Bytes: %u\n" + "ECC Chunk Count : %u\n" + "Payload Size in Bytes : %u\n" + "Auxiliary Size in Bytes: %u\n" + "Auxiliary Status Offset: %u\n" + "Block Mark Byte Offset : %u\n" + "Block Mark Bit Offset : %u\n", + geo->gf_len, + geo->ecc_strength, + geo->page_size, + geo->metadata_size, + geo->ecc_chunk_size, + geo->ecc_chunk_count, + geo->payload_size, + geo->auxiliary_size, + geo->auxiliary_status_offset, + geo->block_mark_byte_offset, + geo->block_mark_bit_offset); +} + +/* Configures the geometry for BCH. */ +int bch_set_geometry(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + struct bch_geometry *bch_geo = &this->bch_geometry; + unsigned int block_count; + unsigned int block_size; + unsigned int metadata_size; + unsigned int ecc_strength; + unsigned int page_size; + unsigned int gf_len; + int ret; + + if (common_nfc_set_geometry(this)) + return !0; + + block_count = bch_geo->ecc_chunk_count - 1; + block_size = bch_geo->ecc_chunk_size; + metadata_size = bch_geo->metadata_size; + ecc_strength = bch_geo->ecc_strength >> 1; + page_size = bch_geo->page_size; + gf_len = bch_geo->gf_len; + + ret = gpmi_enable_clk(this); + if (ret) + goto err_out; + + /* + * Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this + * chip, otherwise it will lock up. So we skip resetting BCH on the MX23. + * On the other hand, the MX28 needs the reset, because one case has been + * seen where the BCH produced ECC errors constantly after 10000 + * consecutive reboots. The latter case has not been seen on the MX23 + * yet, still we don't know if it could happen there as well. + */ + ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); + if (ret) + goto err_out; + + /* Configure layout 0. */ + writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count) + | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size) + | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) + | BF_BCH_FLASH0LAYOUT0_GF(gf_len, this) + | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this), + r->bch_regs + HW_BCH_FLASH0LAYOUT0); + + writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size) + | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) + | BF_BCH_FLASH0LAYOUT1_GF(gf_len, this) + | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this), + r->bch_regs + HW_BCH_FLASH0LAYOUT1); + + /* Set *all* chip selects to use layout 0. */ + writel(0, r->bch_regs + HW_BCH_LAYOUTSELECT); + + /* Enable interrupts. */ + writel(BM_BCH_CTRL_COMPLETE_IRQ_EN, + r->bch_regs + HW_BCH_CTRL_SET); + + gpmi_disable_clk(this); + return 0; +err_out: + return ret; +} + +/* Converts time in nanoseconds to cycles. */ +static unsigned int ns_to_cycles(unsigned int time, + unsigned int period, unsigned int min) +{ + unsigned int k; + + k = (time + period - 1) / period; + return max(k, min); +} + +#define DEF_MIN_PROP_DELAY 5 +#define DEF_MAX_PROP_DELAY 9 +/* Apply timing to current hardware conditions. */ +static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, + struct gpmi_nfc_hardware_timing *hw) +{ + struct timing_threshod *nfc = &timing_default_threshold; + struct resources *r = &this->resources; + struct nand_chip *nand = &this->nand; + struct nand_timing target = this->timing; + bool improved_timing_is_available; + unsigned long clock_frequency_in_hz; + unsigned int clock_period_in_ns; + bool dll_use_half_periods; + unsigned int dll_delay_shift; + unsigned int max_sample_delay_in_ns; + unsigned int address_setup_in_cycles; + unsigned int data_setup_in_ns; + unsigned int data_setup_in_cycles; + unsigned int data_hold_in_cycles; + int ideal_sample_delay_in_ns; + unsigned int sample_delay_factor; + int tEYE; + unsigned int min_prop_delay_in_ns = DEF_MIN_PROP_DELAY; + unsigned int max_prop_delay_in_ns = DEF_MAX_PROP_DELAY; + + /* + * If there are multiple chips, we need to relax the timings to allow + * for signal distortion due to higher capacitance. + */ + if (nand->numchips > 2) { + target.data_setup_in_ns += 10; + target.data_hold_in_ns += 10; + target.address_setup_in_ns += 10; + } else if (nand->numchips > 1) { + target.data_setup_in_ns += 5; + target.data_hold_in_ns += 5; + target.address_setup_in_ns += 5; + } + + /* Check if improved timing information is available. */ + improved_timing_is_available = + (target.tREA_in_ns >= 0) && + (target.tRLOH_in_ns >= 0) && + (target.tRHOH_in_ns >= 0); + + /* Inspect the clock. */ + nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]); + clock_frequency_in_hz = nfc->clock_frequency_in_hz; + clock_period_in_ns = NSEC_PER_SEC / clock_frequency_in_hz; + + /* + * The NFC quantizes setup and hold parameters in terms of clock cycles. + * Here, we quantize the setup and hold timing parameters to the + * next-highest clock period to make sure we apply at least the + * specified times. + * + * For data setup and data hold, the hardware interprets a value of zero + * as the largest possible delay. This is not what's intended by a zero + * in the input parameter, so we impose a minimum of one cycle. + */ + data_setup_in_cycles = ns_to_cycles(target.data_setup_in_ns, + clock_period_in_ns, 1); + data_hold_in_cycles = ns_to_cycles(target.data_hold_in_ns, + clock_period_in_ns, 1); + address_setup_in_cycles = ns_to_cycles(target.address_setup_in_ns, + clock_period_in_ns, 0); + + /* + * The clock's period affects the sample delay in a number of ways: + * + * (1) The NFC HAL tells us the maximum clock period the sample delay + * DLL can tolerate. If the clock period is greater than half that + * maximum, we must configure the DLL to be driven by half periods. + * + * (2) We need to convert from an ideal sample delay, in ns, to a + * "sample delay factor," which the NFC uses. This factor depends on + * whether we're driving the DLL with full or half periods. + * Paraphrasing the reference manual: + * + * AD = SDF x 0.125 x RP + * + * where: + * + * AD is the applied delay, in ns. + * SDF is the sample delay factor, which is dimensionless. + * RP is the reference period, in ns, which is a full clock period + * if the DLL is being driven by full periods, or half that if + * the DLL is being driven by half periods. + * + * Let's re-arrange this in a way that's more useful to us: + * + * 8 + * SDF = AD x ---- + * RP + * + * The reference period is either the clock period or half that, so this + * is: + * + * 8 AD x DDF + * SDF = AD x ----- = -------- + * f x P P + * + * where: + * + * f is 1 or 1/2, depending on how we're driving the DLL. + * P is the clock period. + * DDF is the DLL Delay Factor, a dimensionless value that + * incorporates all the constants in the conversion. + * + * DDF will be either 8 or 16, both of which are powers of two. We can + * reduce the cost of this conversion by using bit shifts instead of + * multiplication or division. Thus: + * + * AD << DDS + * SDF = --------- + * P + * + * or + * + * AD = (SDF >> DDS) x P + * + * where: + * + * DDS is the DLL Delay Shift, the logarithm to base 2 of the DDF. + */ + if (clock_period_in_ns > (nfc->max_dll_clock_period_in_ns >> 1)) { + dll_use_half_periods = true; + dll_delay_shift = 3 + 1; + } else { + dll_use_half_periods = false; + dll_delay_shift = 3; + } + + /* + * Compute the maximum sample delay the NFC allows, under current + * conditions. If the clock is running too slowly, no sample delay is + * possible. + */ + if (clock_period_in_ns > nfc->max_dll_clock_period_in_ns) + max_sample_delay_in_ns = 0; + else { + /* + * Compute the delay implied by the largest sample delay factor + * the NFC allows. + */ + max_sample_delay_in_ns = + (nfc->max_sample_delay_factor * clock_period_in_ns) >> + dll_delay_shift; + + /* + * Check if the implied sample delay larger than the NFC + * actually allows. + */ + if (max_sample_delay_in_ns > nfc->max_dll_delay_in_ns) + max_sample_delay_in_ns = nfc->max_dll_delay_in_ns; + } + + /* + * Check if improved timing information is available. If not, we have to + * use a less-sophisticated algorithm. + */ + if (!improved_timing_is_available) { + /* + * Fold the read setup time required by the NFC into the ideal + * sample delay. + */ + ideal_sample_delay_in_ns = target.gpmi_sample_delay_in_ns + + nfc->internal_data_setup_in_ns; + + /* + * The ideal sample delay may be greater than the maximum + * allowed by the NFC. If so, we can trade off sample delay time + * for more data setup time. + * + * In each iteration of the following loop, we add a cycle to + * the data setup time and subtract a corresponding amount from + * the sample delay until we've satisified the constraints or + * can't do any better. + */ + while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) && + (data_setup_in_cycles < nfc->max_data_setup_cycles)) { + + data_setup_in_cycles++; + ideal_sample_delay_in_ns -= clock_period_in_ns; + + if (ideal_sample_delay_in_ns < 0) + ideal_sample_delay_in_ns = 0; + + } + + /* + * Compute the sample delay factor that corresponds most closely + * to the ideal sample delay. If the result is too large for the + * NFC, use the maximum value. + * + * Notice that we use the ns_to_cycles function to compute the + * sample delay factor. We do this because the form of the + * computation is the same as that for calculating cycles. + */ + sample_delay_factor = + ns_to_cycles( + ideal_sample_delay_in_ns << dll_delay_shift, + clock_period_in_ns, 0); + + if (sample_delay_factor > nfc->max_sample_delay_factor) + sample_delay_factor = nfc->max_sample_delay_factor; + + /* Skip to the part where we return our results. */ + goto return_results; + } + + /* + * If control arrives here, we have more detailed timing information, + * so we can use a better algorithm. + */ + + /* + * Fold the read setup time required by the NFC into the maximum + * propagation delay. + */ + max_prop_delay_in_ns += nfc->internal_data_setup_in_ns; + + /* + * Earlier, we computed the number of clock cycles required to satisfy + * the data setup time. Now, we need to know the actual nanoseconds. + */ + data_setup_in_ns = clock_period_in_ns * data_setup_in_cycles; + + /* + * Compute tEYE, the width of the data eye when reading from the NAND + * Flash. The eye width is fundamentally determined by the data setup + * time, perturbed by propagation delays and some characteristics of the + * NAND Flash device. + * + * start of the eye = max_prop_delay + tREA + * end of the eye = min_prop_delay + tRHOH + data_setup + */ + tEYE = (int)min_prop_delay_in_ns + (int)target.tRHOH_in_ns + + (int)data_setup_in_ns; + + tEYE -= (int)max_prop_delay_in_ns + (int)target.tREA_in_ns; + + /* + * The eye must be open. If it's not, we can try to open it by + * increasing its main forcer, the data setup time. + * + * In each iteration of the following loop, we increase the data setup + * time by a single clock cycle. We do this until either the eye is + * open or we run into NFC limits. + */ + while ((tEYE <= 0) && + (data_setup_in_cycles < nfc->max_data_setup_cycles)) { + /* Give a cycle to data setup. */ + data_setup_in_cycles++; + /* Synchronize the data setup time with the cycles. */ + data_setup_in_ns += clock_period_in_ns; + /* Adjust tEYE accordingly. */ + tEYE += clock_period_in_ns; + } + + /* + * When control arrives here, the eye is open. The ideal time to sample + * the data is in the center of the eye: + * + * end of the eye + start of the eye + * --------------------------------- - data_setup + * 2 + * + * After some algebra, this simplifies to the code immediately below. + */ + ideal_sample_delay_in_ns = + ((int)max_prop_delay_in_ns + + (int)target.tREA_in_ns + + (int)min_prop_delay_in_ns + + (int)target.tRHOH_in_ns - + (int)data_setup_in_ns) >> 1; + + /* + * The following figure illustrates some aspects of a NAND Flash read: + * + * + * __ _____________________________________ + * RDN \_________________/ + * + * <---- tEYE -----> + * /-----------------\ + * Read Data ----------------------------< >--------- + * \-----------------/ + * ^ ^ ^ ^ + * | | | | + * |<--Data Setup -->|<--Delay Time -->| | + * | | | | + * | | | + * | |<-- Quantized Delay Time -->| + * | | | + * + * + * We have some issues we must now address: + * + * (1) The *ideal* sample delay time must not be negative. If it is, we + * jam it to zero. + * + * (2) The *ideal* sample delay time must not be greater than that + * allowed by the NFC. If it is, we can increase the data setup + * time, which will reduce the delay between the end of the data + * setup and the center of the eye. It will also make the eye + * larger, which might help with the next issue... + * + * (3) The *quantized* sample delay time must not fall either before the + * eye opens or after it closes (the latter is the problem + * illustrated in the above figure). + */ + + /* Jam a negative ideal sample delay to zero. */ + if (ideal_sample_delay_in_ns < 0) + ideal_sample_delay_in_ns = 0; + + /* + * Extend the data setup as needed to reduce the ideal sample delay + * below the maximum permitted by the NFC. + */ + while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) && + (data_setup_in_cycles < nfc->max_data_setup_cycles)) { + + /* Give a cycle to data setup. */ + data_setup_in_cycles++; + /* Synchronize the data setup time with the cycles. */ + data_setup_in_ns += clock_period_in_ns; + /* Adjust tEYE accordingly. */ + tEYE += clock_period_in_ns; + + /* + * Decrease the ideal sample delay by one half cycle, to keep it + * in the middle of the eye. + */ + ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1); + + /* Jam a negative ideal sample delay to zero. */ + if (ideal_sample_delay_in_ns < 0) + ideal_sample_delay_in_ns = 0; + } + + /* + * Compute the sample delay factor that corresponds to the ideal sample + * delay. If the result is too large, then use the maximum allowed + * value. + * + * Notice that we use the ns_to_cycles function to compute the sample + * delay factor. We do this because the form of the computation is the + * same as that for calculating cycles. + */ + sample_delay_factor = + ns_to_cycles(ideal_sample_delay_in_ns << dll_delay_shift, + clock_period_in_ns, 0); + + if (sample_delay_factor > nfc->max_sample_delay_factor) + sample_delay_factor = nfc->max_sample_delay_factor; + + /* + * These macros conveniently encapsulate a computation we'll use to + * continuously evaluate whether or not the data sample delay is inside + * the eye. + */ + #define IDEAL_DELAY ((int) ideal_sample_delay_in_ns) + + #define QUANTIZED_DELAY \ + ((int) ((sample_delay_factor * clock_period_in_ns) >> \ + dll_delay_shift)) + + #define DELAY_ERROR (abs(QUANTIZED_DELAY - IDEAL_DELAY)) + + #define SAMPLE_IS_NOT_WITHIN_THE_EYE (DELAY_ERROR > (tEYE >> 1)) + + /* + * While the quantized sample time falls outside the eye, reduce the + * sample delay or extend the data setup to move the sampling point back + * toward the eye. Do not allow the number of data setup cycles to + * exceed the maximum allowed by the NFC. + */ + while (SAMPLE_IS_NOT_WITHIN_THE_EYE && + (data_setup_in_cycles < nfc->max_data_setup_cycles)) { + /* + * If control arrives here, the quantized sample delay falls + * outside the eye. Check if it's before the eye opens, or after + * the eye closes. + */ + if (QUANTIZED_DELAY > IDEAL_DELAY) { + /* + * If control arrives here, the quantized sample delay + * falls after the eye closes. Decrease the quantized + * delay time and then go back to re-evaluate. + */ + if (sample_delay_factor != 0) + sample_delay_factor--; + continue; + } + + /* + * If control arrives here, the quantized sample delay falls + * before the eye opens. Shift the sample point by increasing + * data setup time. This will also make the eye larger. + */ + + /* Give a cycle to data setup. */ + data_setup_in_cycles++; + /* Synchronize the data setup time with the cycles. */ + data_setup_in_ns += clock_period_in_ns; + /* Adjust tEYE accordingly. */ + tEYE += clock_period_in_ns; + + /* + * Decrease the ideal sample delay by one half cycle, to keep it + * in the middle of the eye. + */ + ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1); + + /* ...and one less period for the delay time. */ + ideal_sample_delay_in_ns -= clock_period_in_ns; + + /* Jam a negative ideal sample delay to zero. */ + if (ideal_sample_delay_in_ns < 0) + ideal_sample_delay_in_ns = 0; + + /* + * We have a new ideal sample delay, so re-compute the quantized + * delay. + */ + sample_delay_factor = + ns_to_cycles( + ideal_sample_delay_in_ns << dll_delay_shift, + clock_period_in_ns, 0); + + if (sample_delay_factor > nfc->max_sample_delay_factor) + sample_delay_factor = nfc->max_sample_delay_factor; + } + + /* Control arrives here when we're ready to return our results. */ +return_results: + hw->data_setup_in_cycles = data_setup_in_cycles; + hw->data_hold_in_cycles = data_hold_in_cycles; + hw->address_setup_in_cycles = address_setup_in_cycles; + hw->use_half_periods = dll_use_half_periods; + hw->sample_delay_factor = sample_delay_factor; + hw->device_busy_timeout = GPMI_DEFAULT_BUSY_TIMEOUT; + hw->wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS; + + /* Return success. */ + return 0; +} + +/* + * <1> Firstly, we should know what's the GPMI-clock means. + * The GPMI-clock is the internal clock in the gpmi nand controller. + * If you set 100MHz to gpmi nand controller, the GPMI-clock's period + * is 10ns. Mark the GPMI-clock's period as GPMI-clock-period. + * + * <2> Secondly, we should know what's the frequency on the nand chip pins. + * The frequency on the nand chip pins is derived from the GPMI-clock. + * We can get it from the following equation: + * + * F = G / (DS + DH) + * + * F : the frequency on the nand chip pins. + * G : the GPMI clock, such as 100MHz. + * DS : GPMI_HW_GPMI_TIMING0:DATA_SETUP + * DH : GPMI_HW_GPMI_TIMING0:DATA_HOLD + * + * <3> Thirdly, when the frequency on the nand chip pins is above 33MHz, + * the nand EDO(extended Data Out) timing could be applied. + * The GPMI implements a feedback read strobe to sample the read data. + * The feedback read strobe can be delayed to support the nand EDO timing + * where the read strobe may deasserts before the read data is valid, and + * read data is valid for some time after read strobe. + * + * The following figure illustrates some aspects of a NAND Flash read: + * + * |<---tREA---->| + * | | + * | | | + * |<--tRP-->| | + * | | | + * __ ___|__________________________________ + * RDN \________/ | + * | + * /---------\ + * Read Data --------------< >--------- + * \---------/ + * | | + * |<-D->| + * FeedbackRDN ________ ____________ + * \___________/ + * + * D stands for delay, set in the HW_GPMI_CTRL1:RDN_DELAY. + * + * + * <4> Now, we begin to describe how to compute the right RDN_DELAY. + * + * 4.1) From the aspect of the nand chip pins: + * Delay = (tREA + C - tRP) {1} + * + * tREA : the maximum read access time. From the ONFI nand standards, + * we know that tREA is 16ns in mode 5, tREA is 20ns is mode 4. + * Please check it in : www.onfi.org + * C : a constant for adjust the delay. default is 4. + * tRP : the read pulse width. + * Specified by the HW_GPMI_TIMING0:DATA_SETUP: + * tRP = (GPMI-clock-period) * DATA_SETUP + * + * 4.2) From the aspect of the GPMI nand controller: + * Delay = RDN_DELAY * 0.125 * RP {2} + * + * RP : the DLL reference period. + * if (GPMI-clock-period > DLL_THRETHOLD) + * RP = GPMI-clock-period / 2; + * else + * RP = GPMI-clock-period; + * + * Set the HW_GPMI_CTRL1:HALF_PERIOD if GPMI-clock-period + * is greater DLL_THRETHOLD. In other SOCs, the DLL_THRETHOLD + * is 16ns, but in mx6q, we use 12ns. + * + * 4.3) since {1} equals {2}, we get: + * + * (tREA + 4 - tRP) * 8 + * RDN_DELAY = --------------------- {3} + * RP + * + * 4.4) We only support the fastest asynchronous mode of ONFI nand. + * For some ONFI nand, the mode 4 is the fastest mode; + * while for some ONFI nand, the mode 5 is the fastest mode. + * So we only support the mode 4 and mode 5. It is no need to + * support other modes. + */ +static void gpmi_compute_edo_timing(struct gpmi_nand_data *this, + struct gpmi_nfc_hardware_timing *hw) +{ + struct resources *r = &this->resources; + unsigned long rate = clk_get_rate(r->clock[0]); + int mode = this->timing_mode; + int dll_threshold = this->devdata->max_chain_delay; + unsigned long delay; + unsigned long clk_period; + int t_rea; + int c = 4; + int t_rp; + int rp; + + /* + * [1] for GPMI_HW_GPMI_TIMING0: + * The async mode requires 40MHz for mode 4, 50MHz for mode 5. + * The GPMI can support 100MHz at most. So if we want to + * get the 40MHz or 50MHz, we have to set DS=1, DH=1. + * Set the ADDRESS_SETUP to 0 in mode 4. + */ + hw->data_setup_in_cycles = 1; + hw->data_hold_in_cycles = 1; + hw->address_setup_in_cycles = ((mode == 5) ? 1 : 0); + + /* [2] for GPMI_HW_GPMI_TIMING1 */ + hw->device_busy_timeout = 0x9000; + + /* [3] for GPMI_HW_GPMI_CTRL1 */ + hw->wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY; + + /* + * Enlarge 10 times for the numerator and denominator in {3}. + * This make us to get more accurate result. + */ + clk_period = NSEC_PER_SEC / (rate / 10); + dll_threshold *= 10; + t_rea = ((mode == 5) ? 16 : 20) * 10; + c *= 10; + + t_rp = clk_period * 1; /* DATA_SETUP is 1 */ + + if (clk_period > dll_threshold) { + hw->use_half_periods = 1; + rp = clk_period / 2; + } else { + hw->use_half_periods = 0; + rp = clk_period; + } + + /* + * Multiply the numerator with 10, we could do a round off: + * 7.8 round up to 8; 7.4 round down to 7. + */ + delay = (((t_rea + c - t_rp) * 8) * 10) / rp; + delay = (delay + 5) / 10; + + hw->sample_delay_factor = delay; +} + +static int enable_edo_mode(struct gpmi_nand_data *this, int mode) +{ + struct resources *r = &this->resources; + struct nand_chip *nand = &this->nand; + struct mtd_info *mtd = &this->mtd; + uint8_t *feature; + unsigned long rate; + int ret; + + feature = kzalloc(ONFI_SUBFEATURE_PARAM_LEN, GFP_KERNEL); + if (!feature) + return -ENOMEM; + + nand->select_chip(mtd, 0); + + /* [1] send SET FEATURE commond to NAND */ + feature[0] = mode; + ret = nand->onfi_set_features(mtd, nand, + ONFI_FEATURE_ADDR_TIMING_MODE, feature); + if (ret) + goto err_out; + + /* [2] send GET FEATURE command to double-check the timing mode */ + memset(feature, 0, ONFI_SUBFEATURE_PARAM_LEN); + ret = nand->onfi_get_features(mtd, nand, + ONFI_FEATURE_ADDR_TIMING_MODE, feature); + if (ret || feature[0] != mode) + goto err_out; + + nand->select_chip(mtd, -1); + + /* [3] set the main IO clock, 100MHz for mode 5, 80MHz for mode 4. */ + rate = (mode == 5) ? 100000000 : 80000000; + clk_set_rate(r->clock[0], rate); + + /* Let the gpmi_begin() re-compute the timing again. */ + this->flags &= ~GPMI_TIMING_INIT_OK; + + this->flags |= GPMI_ASYNC_EDO_ENABLED; + this->timing_mode = mode; + kfree(feature); + dev_info(this->dev, "enable the asynchronous EDO mode %d\n", mode); + return 0; + +err_out: + nand->select_chip(mtd, -1); + kfree(feature); + dev_err(this->dev, "mode:%d ,failed in set feature.\n", mode); + return -EINVAL; +} + +int gpmi_extra_init(struct gpmi_nand_data *this) +{ + struct nand_chip *chip = &this->nand; + + /* Enable the asynchronous EDO feature. */ + if (GPMI_IS_MX6(this) && chip->onfi_version) { + int mode = onfi_get_async_timing_mode(chip); + + /* We only support the timing mode 4 and mode 5. */ + if (mode & ONFI_TIMING_MODE_5) + mode = 5; + else if (mode & ONFI_TIMING_MODE_4) + mode = 4; + else + return 0; + + return enable_edo_mode(this, mode); + } + return 0; +} + +/* Begin the I/O */ +void gpmi_begin(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + void __iomem *gpmi_regs = r->gpmi_regs; + unsigned int clock_period_in_ns; + uint32_t reg; + unsigned int dll_wait_time_in_us; + struct gpmi_nfc_hardware_timing hw; + int ret; + + /* Enable the clock. */ + ret = gpmi_enable_clk(this); + if (ret) { + dev_err(this->dev, "We failed in enable the clk\n"); + goto err_out; + } + + /* Only initialize the timing once */ + if (this->flags & GPMI_TIMING_INIT_OK) + return; + this->flags |= GPMI_TIMING_INIT_OK; + + if (this->flags & GPMI_ASYNC_EDO_ENABLED) + gpmi_compute_edo_timing(this, &hw); + else + gpmi_nfc_compute_hardware_timing(this, &hw); + + /* [1] Set HW_GPMI_TIMING0 */ + reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) | + BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles) | + BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles); + + writel(reg, gpmi_regs + HW_GPMI_TIMING0); + + /* [2] Set HW_GPMI_TIMING1 */ + writel(BF_GPMI_TIMING1_BUSY_TIMEOUT(hw.device_busy_timeout), + gpmi_regs + HW_GPMI_TIMING1); + + /* [3] The following code is to set the HW_GPMI_CTRL1. */ + + /* Set the WRN_DLY_SEL */ + writel(BM_GPMI_CTRL1_WRN_DLY_SEL, gpmi_regs + HW_GPMI_CTRL1_CLR); + writel(BF_GPMI_CTRL1_WRN_DLY_SEL(hw.wrn_dly_sel), + gpmi_regs + HW_GPMI_CTRL1_SET); + + /* DLL_ENABLE must be set to 0 when setting RDN_DELAY or HALF_PERIOD. */ + writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_CLR); + + /* Clear out the DLL control fields. */ + reg = BM_GPMI_CTRL1_RDN_DELAY | BM_GPMI_CTRL1_HALF_PERIOD; + writel(reg, gpmi_regs + HW_GPMI_CTRL1_CLR); + + /* If no sample delay is called for, return immediately. */ + if (!hw.sample_delay_factor) + return; + + /* Set RDN_DELAY or HALF_PERIOD. */ + reg = ((hw.use_half_periods) ? BM_GPMI_CTRL1_HALF_PERIOD : 0) + | BF_GPMI_CTRL1_RDN_DELAY(hw.sample_delay_factor); + + writel(reg, gpmi_regs + HW_GPMI_CTRL1_SET); + + /* At last, we enable the DLL. */ + writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_SET); + + /* + * After we enable the GPMI DLL, we have to wait 64 clock cycles before + * we can use the GPMI. Calculate the amount of time we need to wait, + * in microseconds. + */ + clock_period_in_ns = NSEC_PER_SEC / clk_get_rate(r->clock[0]); + dll_wait_time_in_us = (clock_period_in_ns * 64) / 1000; + + if (!dll_wait_time_in_us) + dll_wait_time_in_us = 1; + + /* Wait for the DLL to settle. */ + udelay(dll_wait_time_in_us); + +err_out: + return; +} + +void gpmi_end(struct gpmi_nand_data *this) +{ + gpmi_disable_clk(this); +} + +/* Clears a BCH interrupt. */ +void gpmi_clear_bch(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + writel(BM_BCH_CTRL_COMPLETE_IRQ, r->bch_regs + HW_BCH_CTRL_CLR); +} + +/* Returns the Ready/Busy status of the given chip. */ +int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) +{ + struct resources *r = &this->resources; + uint32_t mask = 0; + uint32_t reg = 0; + + if (GPMI_IS_MX23(this)) { + mask = MX23_BM_GPMI_DEBUG_READY0 << chip; + reg = readl(r->gpmi_regs + HW_GPMI_DEBUG); + } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6(this)) { + /* + * In the imx6, all the ready/busy pins are bound + * together. So we only need to check chip 0. + */ + if (GPMI_IS_MX6(this)) + chip = 0; + + /* MX28 shares the same R/B register as MX6Q. */ + mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip); + reg = readl(r->gpmi_regs + HW_GPMI_STAT); + } else + dev_err(this->dev, "unknown arch.\n"); + return reg & mask; +} + +static inline void set_dma_type(struct gpmi_nand_data *this, + enum dma_ops_type type) +{ + this->last_dma_type = this->dma_type; + this->dma_type = type; +} + +int gpmi_send_command(struct gpmi_nand_data *this) +{ + struct dma_chan *channel = get_dma_chan(this); + struct dma_async_tx_descriptor *desc; + struct scatterlist *sgl; + int chip = this->current_chip; + u32 pio[3]; + + /* [1] send out the PIO words */ + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE) + | BM_GPMI_CTRL0_ADDRESS_INCREMENT + | BF_GPMI_CTRL0_XFER_COUNT(this->command_length); + pio[1] = pio[2] = 0; + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, + ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); + if (!desc) + return -EINVAL; + + /* [2] send out the COMMAND + ADDRESS string stored in @buffer */ + sgl = &this->cmd_sgl; + + sg_init_one(sgl, this->cmd_buffer, this->command_length); + dma_map_sg(this->dev, sgl, 1, DMA_TO_DEVICE); + desc = dmaengine_prep_slave_sg(channel, + sgl, 1, DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + /* [3] submit the DMA */ + set_dma_type(this, DMA_FOR_COMMAND); + return start_dma_without_bch_irq(this, desc); +} + +int gpmi_send_data(struct gpmi_nand_data *this) +{ + struct dma_async_tx_descriptor *desc; + struct dma_chan *channel = get_dma_chan(this); + int chip = this->current_chip; + uint32_t command_mode; + uint32_t address; + u32 pio[2]; + + /* [1] PIO */ + command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE; + address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA; + + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(address) + | BF_GPMI_CTRL0_XFER_COUNT(this->upper_len); + pio[1] = 0; + desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, + ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); + if (!desc) + return -EINVAL; + + /* [2] send DMA request */ + prepare_data_dma(this, DMA_TO_DEVICE); + desc = dmaengine_prep_slave_sg(channel, &this->data_sgl, + 1, DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + /* [3] submit the DMA */ + set_dma_type(this, DMA_FOR_WRITE_DATA); + return start_dma_without_bch_irq(this, desc); +} + +int gpmi_read_data(struct gpmi_nand_data *this) +{ + struct dma_async_tx_descriptor *desc; + struct dma_chan *channel = get_dma_chan(this); + int chip = this->current_chip; + u32 pio[2]; + + /* [1] : send PIO */ + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA) + | BF_GPMI_CTRL0_XFER_COUNT(this->upper_len); + pio[1] = 0; + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, + ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); + if (!desc) + return -EINVAL; + + /* [2] : send DMA request */ + prepare_data_dma(this, DMA_FROM_DEVICE); + desc = dmaengine_prep_slave_sg(channel, &this->data_sgl, + 1, DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + /* [3] : submit the DMA */ + set_dma_type(this, DMA_FOR_READ_DATA); + return start_dma_without_bch_irq(this, desc); +} + +int gpmi_send_page(struct gpmi_nand_data *this, + dma_addr_t payload, dma_addr_t auxiliary) +{ + struct bch_geometry *geo = &this->bch_geometry; + uint32_t command_mode; + uint32_t address; + uint32_t ecc_command; + uint32_t buffer_mask; + struct dma_async_tx_descriptor *desc; + struct dma_chan *channel = get_dma_chan(this); + int chip = this->current_chip; + u32 pio[6]; + + /* A DMA descriptor that does an ECC page read. */ + command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE; + address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA; + ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE; + buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE | + BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY; + + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(address) + | BF_GPMI_CTRL0_XFER_COUNT(0); + pio[1] = 0; + pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC + | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command) + | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask); + pio[3] = geo->page_size; + pio[4] = payload; + pio[5] = auxiliary; + + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, + ARRAY_SIZE(pio), DMA_TRANS_NONE, + DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + set_dma_type(this, DMA_FOR_WRITE_ECC_PAGE); + return start_dma_with_bch_irq(this, desc); +} + +int gpmi_read_page(struct gpmi_nand_data *this, + dma_addr_t payload, dma_addr_t auxiliary) +{ + struct bch_geometry *geo = &this->bch_geometry; + uint32_t command_mode; + uint32_t address; + uint32_t ecc_command; + uint32_t buffer_mask; + struct dma_async_tx_descriptor *desc; + struct dma_chan *channel = get_dma_chan(this); + int chip = this->current_chip; + u32 pio[6]; + + /* [1] Wait for the chip to report ready. */ + command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY; + address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA; + + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(address) + | BF_GPMI_CTRL0_XFER_COUNT(0); + pio[1] = 0; + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, 2, + DMA_TRANS_NONE, 0); + if (!desc) + return -EINVAL; + + /* [2] Enable the BCH block and read. */ + command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ; + address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA; + ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE; + buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE + | BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY; + + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(address) + | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size); + + pio[1] = 0; + pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC + | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command) + | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask); + pio[3] = geo->page_size; + pio[4] = payload; + pio[5] = auxiliary; + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, + ARRAY_SIZE(pio), DMA_TRANS_NONE, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + /* [3] Disable the BCH block */ + command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY; + address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA; + + pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode) + | BM_GPMI_CTRL0_WORD_LENGTH + | BF_GPMI_CTRL0_CS(chip, this) + | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this) + | BF_GPMI_CTRL0_ADDRESS(address) + | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size); + pio[1] = 0; + pio[2] = 0; /* clear GPMI_HW_GPMI_ECCCTRL, disable the BCH. */ + desc = dmaengine_prep_slave_sg(channel, + (struct scatterlist *)pio, 3, + DMA_TRANS_NONE, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EINVAL; + + /* [4] submit the DMA */ + set_dma_type(this, DMA_FOR_READ_ECC_PAGE); + return start_dma_with_bch_irq(this, desc); +} + +/** + * gpmi_copy_bits - copy bits from one memory region to another + * @dst: destination buffer + * @dst_bit_off: bit offset we're starting to write at + * @src: source buffer + * @src_bit_off: bit offset we're starting to read from + * @nbits: number of bits to copy + * + * This functions copies bits from one memory region to another, and is used by + * the GPMI driver to copy ECC sections which are not guaranteed to be byte + * aligned. + * + * src and dst should not overlap. + * + */ +void gpmi_copy_bits(u8 *dst, size_t dst_bit_off, + const u8 *src, size_t src_bit_off, + size_t nbits) +{ + size_t i; + size_t nbytes; + u32 src_buffer = 0; + size_t bits_in_src_buffer = 0; + + if (!nbits) + return; + + /* + * Move src and dst pointers to the closest byte pointer and store bit + * offsets within a byte. + */ + src += src_bit_off / 8; + src_bit_off %= 8; + + dst += dst_bit_off / 8; + dst_bit_off %= 8; + + /* + * Initialize the src_buffer value with bits available in the first + * byte of data so that we end up with a byte aligned src pointer. + */ + if (src_bit_off) { + src_buffer = src[0] >> src_bit_off; + if (nbits >= (8 - src_bit_off)) { + bits_in_src_buffer += 8 - src_bit_off; + } else { + src_buffer &= GENMASK(nbits - 1, 0); + bits_in_src_buffer += nbits; + } + nbits -= bits_in_src_buffer; + src++; + } + + /* Calculate the number of bytes that can be copied from src to dst. */ + nbytes = nbits / 8; + + /* Try to align dst to a byte boundary. */ + if (dst_bit_off) { + if (bits_in_src_buffer < (8 - dst_bit_off) && nbytes) { + src_buffer |= src[0] << bits_in_src_buffer; + bits_in_src_buffer += 8; + src++; + nbytes--; + } + + if (bits_in_src_buffer >= (8 - dst_bit_off)) { + dst[0] &= GENMASK(dst_bit_off - 1, 0); + dst[0] |= src_buffer << dst_bit_off; + src_buffer >>= (8 - dst_bit_off); + bits_in_src_buffer -= (8 - dst_bit_off); + dst_bit_off = 0; + dst++; + if (bits_in_src_buffer > 7) { + bits_in_src_buffer -= 8; + dst[0] = src_buffer; + dst++; + src_buffer >>= 8; + } + } + } + + if (!bits_in_src_buffer && !dst_bit_off) { + /* + * Both src and dst pointers are byte aligned, thus we can + * just use the optimized memcpy function. + */ + if (nbytes) + memcpy(dst, src, nbytes); + } else { + /* + * src buffer is not byte aligned, hence we have to copy each + * src byte to the src_buffer variable before extracting a byte + * to store in dst. + */ + for (i = 0; i < nbytes; i++) { + src_buffer |= src[i] << bits_in_src_buffer; + dst[i] = src_buffer; + src_buffer >>= 8; + } + } + /* Update dst and src pointers */ + dst += nbytes; + src += nbytes; + + /* + * nbits is the number of remaining bits. It should not exceed 8 as + * we've already copied as much bytes as possible. + */ + nbits %= 8; + + /* + * If there's no more bits to copy to the destination and src buffer + * was already byte aligned, then we're done. + */ + if (!nbits && !bits_in_src_buffer) + return; + + /* Copy the remaining bits to src_buffer */ + if (nbits) + src_buffer |= (*src & GENMASK(nbits - 1, 0)) << + bits_in_src_buffer; + bits_in_src_buffer += nbits; + + /* + * In case there were not enough bits to get a byte aligned dst buffer + * prepare the src_buffer variable to match the dst organization (shift + * src_buffer by dst_bit_off and retrieve the least significant bits + * from dst). + */ + if (dst_bit_off) + src_buffer = (src_buffer << dst_bit_off) | + (*dst & GENMASK(dst_bit_off - 1, 0)); + bits_in_src_buffer += dst_bit_off; + + /* + * Keep most significant bits from dst if we end up with an unaligned + * number of bits. + */ + nbytes = bits_in_src_buffer / 8; + if (bits_in_src_buffer % 8) { + src_buffer |= (dst[nbytes] & + GENMASK(7, bits_in_src_buffer % 8)) << + (nbytes * 8); + nbytes++; + } + + /* Copy the remaining bytes to dst */ + for (i = 0; i < nbytes; i++) { + dst[i] = src_buffer; + src_buffer >>= 8; + } +} diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c new file mode 100644 index 000000000..1b8f3500e --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -0,0 +1,2051 @@ +/* + * Freescale GPMI NAND Flash Driver + * + * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. + * Copyright (C) 2008 Embedded Alley Solutions, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/mtd/partitions.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_mtd.h> +#include "gpmi-nand.h" +#include "bch-regs.h" + +/* Resource names for the GPMI NAND driver. */ +#define GPMI_NAND_GPMI_REGS_ADDR_RES_NAME "gpmi-nand" +#define GPMI_NAND_BCH_REGS_ADDR_RES_NAME "bch" +#define GPMI_NAND_BCH_INTERRUPT_RES_NAME "bch" + +/* add our owner bbt descriptor */ +static uint8_t scan_ff_pattern[] = { 0xff }; +static struct nand_bbt_descr gpmi_bbt_descr = { + .options = 0, + .offs = 0, + .len = 1, + .pattern = scan_ff_pattern +}; + +/* + * We may change the layout if we can get the ECC info from the datasheet, + * else we will use all the (page + OOB). + */ +static struct nand_ecclayout gpmi_hw_ecclayout = { + .eccbytes = 0, + .eccpos = { 0, }, + .oobfree = { {.offset = 0, .length = 0} } +}; + +static const struct gpmi_devdata gpmi_devdata_imx23 = { + .type = IS_MX23, + .bch_max_ecc_strength = 20, + .max_chain_delay = 16, +}; + +static const struct gpmi_devdata gpmi_devdata_imx28 = { + .type = IS_MX28, + .bch_max_ecc_strength = 20, + .max_chain_delay = 16, +}; + +static const struct gpmi_devdata gpmi_devdata_imx6q = { + .type = IS_MX6Q, + .bch_max_ecc_strength = 40, + .max_chain_delay = 12, +}; + +static const struct gpmi_devdata gpmi_devdata_imx6sx = { + .type = IS_MX6SX, + .bch_max_ecc_strength = 62, + .max_chain_delay = 12, +}; + +static irqreturn_t bch_irq(int irq, void *cookie) +{ + struct gpmi_nand_data *this = cookie; + + gpmi_clear_bch(this); + complete(&this->bch_done); + return IRQ_HANDLED; +} + +/* + * Calculate the ECC strength by hand: + * E : The ECC strength. + * G : the length of Galois Field. + * N : The chunk count of per page. + * O : the oobsize of the NAND chip. + * M : the metasize of per page. + * + * The formula is : + * E * G * N + * ------------ <= (O - M) + * 8 + * + * So, we get E by: + * (O - M) * 8 + * E <= ------------- + * G * N + */ +static inline int get_ecc_strength(struct gpmi_nand_data *this) +{ + struct bch_geometry *geo = &this->bch_geometry; + struct mtd_info *mtd = &this->mtd; + int ecc_strength; + + ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8) + / (geo->gf_len * geo->ecc_chunk_count); + + /* We need the minor even number. */ + return round_down(ecc_strength, 2); +} + +static inline bool gpmi_check_ecc(struct gpmi_nand_data *this) +{ + struct bch_geometry *geo = &this->bch_geometry; + + /* Do the sanity check. */ + if (GPMI_IS_MX23(this) || GPMI_IS_MX28(this)) { + /* The mx23/mx28 only support the GF13. */ + if (geo->gf_len == 14) + return false; + } + return geo->ecc_strength <= this->devdata->bch_max_ecc_strength; +} + +/* + * If we can get the ECC information from the nand chip, we do not + * need to calculate them ourselves. + * + * We may have available oob space in this case. + */ +static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this) +{ + struct bch_geometry *geo = &this->bch_geometry; + struct mtd_info *mtd = &this->mtd; + struct nand_chip *chip = mtd->priv; + struct nand_oobfree *of = gpmi_hw_ecclayout.oobfree; + unsigned int block_mark_bit_offset; + + if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0)) + return false; + + switch (chip->ecc_step_ds) { + case SZ_512: + geo->gf_len = 13; + break; + case SZ_1K: + geo->gf_len = 14; + break; + default: + dev_err(this->dev, + "unsupported nand chip. ecc bits : %d, ecc size : %d\n", + chip->ecc_strength_ds, chip->ecc_step_ds); + return false; + } + geo->ecc_chunk_size = chip->ecc_step_ds; + geo->ecc_strength = round_up(chip->ecc_strength_ds, 2); + if (!gpmi_check_ecc(this)) + return false; + + /* Keep the C >= O */ + if (geo->ecc_chunk_size < mtd->oobsize) { + dev_err(this->dev, + "unsupported nand chip. ecc size: %d, oob size : %d\n", + chip->ecc_step_ds, mtd->oobsize); + return false; + } + + /* The default value, see comment in the legacy_set_geometry(). */ + geo->metadata_size = 10; + + geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size; + + /* + * Now, the NAND chip with 2K page(data chunk is 512byte) shows below: + * + * | P | + * |<----------------------------------------------------->| + * | | + * | (Block Mark) | + * | P' | | | | + * |<-------------------------------------------->| D | | O' | + * | |<---->| |<--->| + * V V V V V + * +---+----------+-+----------+-+----------+-+----------+-+-----+ + * | M | data |E| data |E| data |E| data |E| | + * +---+----------+-+----------+-+----------+-+----------+-+-----+ + * ^ ^ + * | O | + * |<------------>| + * | | + * + * P : the page size for BCH module. + * E : The ECC strength. + * G : the length of Galois Field. + * N : The chunk count of per page. + * M : the metasize of per page. + * C : the ecc chunk size, aka the "data" above. + * P': the nand chip's page size. + * O : the nand chip's oob size. + * O': the free oob. + * + * The formula for P is : + * + * E * G * N + * P = ------------ + P' + M + * 8 + * + * The position of block mark moves forward in the ECC-based view + * of page, and the delta is: + * + * E * G * (N - 1) + * D = (---------------- + M) + * 8 + * + * Please see the comment in legacy_set_geometry(). + * With the condition C >= O , we still can get same result. + * So the bit position of the physical block mark within the ECC-based + * view of the page is : + * (P' - D) * 8 + */ + geo->page_size = mtd->writesize + geo->metadata_size + + (geo->gf_len * geo->ecc_strength * geo->ecc_chunk_count) / 8; + + /* The available oob size we have. */ + if (geo->page_size < mtd->writesize + mtd->oobsize) { + of->offset = geo->page_size - mtd->writesize; + of->length = mtd->oobsize - of->offset; + } + + geo->payload_size = mtd->writesize; + + geo->auxiliary_status_offset = ALIGN(geo->metadata_size, 4); + geo->auxiliary_size = ALIGN(geo->metadata_size, 4) + + ALIGN(geo->ecc_chunk_count, 4); + + if (!this->swap_block_mark) + return true; + + /* For bit swap. */ + block_mark_bit_offset = mtd->writesize * 8 - + (geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1) + + geo->metadata_size * 8); + + geo->block_mark_byte_offset = block_mark_bit_offset / 8; + geo->block_mark_bit_offset = block_mark_bit_offset % 8; + return true; +} + +static int legacy_set_geometry(struct gpmi_nand_data *this) +{ + struct bch_geometry *geo = &this->bch_geometry; + struct mtd_info *mtd = &this->mtd; + unsigned int metadata_size; + unsigned int status_size; + unsigned int block_mark_bit_offset; + + /* + * The size of the metadata can be changed, though we set it to 10 + * bytes now. But it can't be too large, because we have to save + * enough space for BCH. + */ + geo->metadata_size = 10; + + /* The default for the length of Galois Field. */ + geo->gf_len = 13; + + /* The default for chunk size. */ + geo->ecc_chunk_size = 512; + while (geo->ecc_chunk_size < mtd->oobsize) { + geo->ecc_chunk_size *= 2; /* keep C >= O */ + geo->gf_len = 14; + } + + geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size; + + /* We use the same ECC strength for all chunks. */ + geo->ecc_strength = get_ecc_strength(this); + if (!gpmi_check_ecc(this)) { + dev_err(this->dev, + "required ecc strength of the NAND chip: %d is not supported by the GPMI controller (%d)\n", + geo->ecc_strength, + this->devdata->bch_max_ecc_strength); + return -EINVAL; + } + + geo->page_size = mtd->writesize + mtd->oobsize; + geo->payload_size = mtd->writesize; + + /* + * The auxiliary buffer contains the metadata and the ECC status. The + * metadata is padded to the nearest 32-bit boundary. The ECC status + * contains one byte for every ECC chunk, and is also padded to the + * nearest 32-bit boundary. + */ + metadata_size = ALIGN(geo->metadata_size, 4); + status_size = ALIGN(geo->ecc_chunk_count, 4); + + geo->auxiliary_size = metadata_size + status_size; + geo->auxiliary_status_offset = metadata_size; + + if (!this->swap_block_mark) + return 0; + + /* + * We need to compute the byte and bit offsets of + * the physical block mark within the ECC-based view of the page. + * + * NAND chip with 2K page shows below: + * (Block Mark) + * | | + * | D | + * |<---->| + * V V + * +---+----------+-+----------+-+----------+-+----------+-+ + * | M | data |E| data |E| data |E| data |E| + * +---+----------+-+----------+-+----------+-+----------+-+ + * + * The position of block mark moves forward in the ECC-based view + * of page, and the delta is: + * + * E * G * (N - 1) + * D = (---------------- + M) + * 8 + * + * With the formula to compute the ECC strength, and the condition + * : C >= O (C is the ecc chunk size) + * + * It's easy to deduce to the following result: + * + * E * G (O - M) C - M C - M + * ----------- <= ------- <= -------- < --------- + * 8 N N (N - 1) + * + * So, we get: + * + * E * G * (N - 1) + * D = (---------------- + M) < C + * 8 + * + * The above inequality means the position of block mark + * within the ECC-based view of the page is still in the data chunk, + * and it's NOT in the ECC bits of the chunk. + * + * Use the following to compute the bit position of the + * physical block mark within the ECC-based view of the page: + * (page_size - D) * 8 + * + * --Huang Shijie + */ + block_mark_bit_offset = mtd->writesize * 8 - + (geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1) + + geo->metadata_size * 8); + + geo->block_mark_byte_offset = block_mark_bit_offset / 8; + geo->block_mark_bit_offset = block_mark_bit_offset % 8; + return 0; +} + +int common_nfc_set_geometry(struct gpmi_nand_data *this) +{ + if (of_property_read_bool(this->dev->of_node, "fsl,use-minimum-ecc") + && set_geometry_by_ecc_info(this)) + return 0; + return legacy_set_geometry(this); +} + +struct dma_chan *get_dma_chan(struct gpmi_nand_data *this) +{ + /* We use the DMA channel 0 to access all the nand chips. */ + return this->dma_chans[0]; +} + +/* Can we use the upper's buffer directly for DMA? */ +void prepare_data_dma(struct gpmi_nand_data *this, enum dma_data_direction dr) +{ + struct scatterlist *sgl = &this->data_sgl; + int ret; + + /* first try to map the upper buffer directly */ + if (virt_addr_valid(this->upper_buf) && + !object_is_on_stack(this->upper_buf)) { + sg_init_one(sgl, this->upper_buf, this->upper_len); + ret = dma_map_sg(this->dev, sgl, 1, dr); + if (ret == 0) + goto map_fail; + + this->direct_dma_map_ok = true; + return; + } + +map_fail: + /* We have to use our own DMA buffer. */ + sg_init_one(sgl, this->data_buffer_dma, this->upper_len); + + if (dr == DMA_TO_DEVICE) + memcpy(this->data_buffer_dma, this->upper_buf, this->upper_len); + + dma_map_sg(this->dev, sgl, 1, dr); + + this->direct_dma_map_ok = false; +} + +/* This will be called after the DMA operation is finished. */ +static void dma_irq_callback(void *param) +{ + struct gpmi_nand_data *this = param; + struct completion *dma_c = &this->dma_done; + + switch (this->dma_type) { + case DMA_FOR_COMMAND: + dma_unmap_sg(this->dev, &this->cmd_sgl, 1, DMA_TO_DEVICE); + break; + + case DMA_FOR_READ_DATA: + dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE); + if (this->direct_dma_map_ok == false) + memcpy(this->upper_buf, this->data_buffer_dma, + this->upper_len); + break; + + case DMA_FOR_WRITE_DATA: + dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE); + break; + + case DMA_FOR_READ_ECC_PAGE: + case DMA_FOR_WRITE_ECC_PAGE: + /* We have to wait the BCH interrupt to finish. */ + break; + + default: + dev_err(this->dev, "in wrong DMA operation.\n"); + } + + complete(dma_c); +} + +int start_dma_without_bch_irq(struct gpmi_nand_data *this, + struct dma_async_tx_descriptor *desc) +{ + struct completion *dma_c = &this->dma_done; + unsigned long timeout; + + init_completion(dma_c); + + desc->callback = dma_irq_callback; + desc->callback_param = this; + dmaengine_submit(desc); + dma_async_issue_pending(get_dma_chan(this)); + + /* Wait for the interrupt from the DMA block. */ + timeout = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000)); + if (!timeout) { + dev_err(this->dev, "DMA timeout, last DMA :%d\n", + this->last_dma_type); + gpmi_dump_info(this); + return -ETIMEDOUT; + } + return 0; +} + +/* + * This function is used in BCH reading or BCH writing pages. + * It will wait for the BCH interrupt as long as ONE second. + * Actually, we must wait for two interrupts : + * [1] firstly the DMA interrupt and + * [2] secondly the BCH interrupt. + */ +int start_dma_with_bch_irq(struct gpmi_nand_data *this, + struct dma_async_tx_descriptor *desc) +{ + struct completion *bch_c = &this->bch_done; + unsigned long timeout; + + /* Prepare to receive an interrupt from the BCH block. */ + init_completion(bch_c); + + /* start the DMA */ + start_dma_without_bch_irq(this, desc); + + /* Wait for the interrupt from the BCH block. */ + timeout = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000)); + if (!timeout) { + dev_err(this->dev, "BCH timeout, last DMA :%d\n", + this->last_dma_type); + gpmi_dump_info(this); + return -ETIMEDOUT; + } + return 0; +} + +static int acquire_register_block(struct gpmi_nand_data *this, + const char *res_name) +{ + struct platform_device *pdev = this->pdev; + struct resources *res = &this->resources; + struct resource *r; + void __iomem *p; + + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name); + p = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(p)) + return PTR_ERR(p); + + if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME)) + res->gpmi_regs = p; + else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME)) + res->bch_regs = p; + else + dev_err(this->dev, "unknown resource name : %s\n", res_name); + + return 0; +} + +static int acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h) +{ + struct platform_device *pdev = this->pdev; + const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME; + struct resource *r; + int err; + + r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name); + if (!r) { + dev_err(this->dev, "Can't get resource for %s\n", res_name); + return -ENODEV; + } + + err = devm_request_irq(this->dev, r->start, irq_h, 0, res_name, this); + if (err) + dev_err(this->dev, "error requesting BCH IRQ\n"); + + return err; +} + +static void release_dma_channels(struct gpmi_nand_data *this) +{ + unsigned int i; + for (i = 0; i < DMA_CHANS; i++) + if (this->dma_chans[i]) { + dma_release_channel(this->dma_chans[i]); + this->dma_chans[i] = NULL; + } +} + +static int acquire_dma_channels(struct gpmi_nand_data *this) +{ + struct platform_device *pdev = this->pdev; + struct dma_chan *dma_chan; + + /* request dma channel */ + dma_chan = dma_request_slave_channel(&pdev->dev, "rx-tx"); + if (!dma_chan) { + dev_err(this->dev, "Failed to request DMA channel.\n"); + goto acquire_err; + } + + this->dma_chans[0] = dma_chan; + return 0; + +acquire_err: + release_dma_channels(this); + return -EINVAL; +} + +static char *extra_clks_for_mx6q[GPMI_CLK_MAX] = { + "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch", +}; + +static int gpmi_get_clks(struct gpmi_nand_data *this) +{ + struct resources *r = &this->resources; + char **extra_clks = NULL; + struct clk *clk; + int err, i; + + /* The main clock is stored in the first. */ + r->clock[0] = devm_clk_get(this->dev, "gpmi_io"); + if (IS_ERR(r->clock[0])) { + err = PTR_ERR(r->clock[0]); + goto err_clock; + } + + /* Get extra clocks */ + if (GPMI_IS_MX6(this)) + extra_clks = extra_clks_for_mx6q; + if (!extra_clks) + return 0; + + for (i = 1; i < GPMI_CLK_MAX; i++) { + if (extra_clks[i - 1] == NULL) + break; + + clk = devm_clk_get(this->dev, extra_clks[i - 1]); + if (IS_ERR(clk)) { + err = PTR_ERR(clk); + goto err_clock; + } + + r->clock[i] = clk; + } + + if (GPMI_IS_MX6(this)) + /* + * Set the default value for the gpmi clock. + * + * If you want to use the ONFI nand which is in the + * Synchronous Mode, you should change the clock as you need. + */ + clk_set_rate(r->clock[0], 22000000); + + return 0; + +err_clock: + dev_dbg(this->dev, "failed in finding the clocks.\n"); + return err; +} + +static int acquire_resources(struct gpmi_nand_data *this) +{ + int ret; + + ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME); + if (ret) + goto exit_regs; + + ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME); + if (ret) + goto exit_regs; + + ret = acquire_bch_irq(this, bch_irq); + if (ret) + goto exit_regs; + + ret = acquire_dma_channels(this); + if (ret) + goto exit_regs; + + ret = gpmi_get_clks(this); + if (ret) + goto exit_clock; + return 0; + +exit_clock: + release_dma_channels(this); +exit_regs: + return ret; +} + +static void release_resources(struct gpmi_nand_data *this) +{ + release_dma_channels(this); +} + +static int init_hardware(struct gpmi_nand_data *this) +{ + int ret; + + /* + * This structure contains the "safe" GPMI timing that should succeed + * with any NAND Flash device + * (although, with less-than-optimal performance). + */ + struct nand_timing safe_timing = { + .data_setup_in_ns = 80, + .data_hold_in_ns = 60, + .address_setup_in_ns = 25, + .gpmi_sample_delay_in_ns = 6, + .tREA_in_ns = -1, + .tRLOH_in_ns = -1, + .tRHOH_in_ns = -1, + }; + + /* Initialize the hardwares. */ + ret = gpmi_init(this); + if (ret) + return ret; + + this->timing = safe_timing; + return 0; +} + +static int read_page_prepare(struct gpmi_nand_data *this, + void *destination, unsigned length, + void *alt_virt, dma_addr_t alt_phys, unsigned alt_size, + void **use_virt, dma_addr_t *use_phys) +{ + struct device *dev = this->dev; + + if (virt_addr_valid(destination)) { + dma_addr_t dest_phys; + + dest_phys = dma_map_single(dev, destination, + length, DMA_FROM_DEVICE); + if (dma_mapping_error(dev, dest_phys)) { + if (alt_size < length) { + dev_err(dev, "Alternate buffer is too small\n"); + return -ENOMEM; + } + goto map_failed; + } + *use_virt = destination; + *use_phys = dest_phys; + this->direct_dma_map_ok = true; + return 0; + } + +map_failed: + *use_virt = alt_virt; + *use_phys = alt_phys; + this->direct_dma_map_ok = false; + return 0; +} + +static inline void read_page_end(struct gpmi_nand_data *this, + void *destination, unsigned length, + void *alt_virt, dma_addr_t alt_phys, unsigned alt_size, + void *used_virt, dma_addr_t used_phys) +{ + if (this->direct_dma_map_ok) + dma_unmap_single(this->dev, used_phys, length, DMA_FROM_DEVICE); +} + +static inline void read_page_swap_end(struct gpmi_nand_data *this, + void *destination, unsigned length, + void *alt_virt, dma_addr_t alt_phys, unsigned alt_size, + void *used_virt, dma_addr_t used_phys) +{ + if (!this->direct_dma_map_ok) + memcpy(destination, alt_virt, length); +} + +static int send_page_prepare(struct gpmi_nand_data *this, + const void *source, unsigned length, + void *alt_virt, dma_addr_t alt_phys, unsigned alt_size, + const void **use_virt, dma_addr_t *use_phys) +{ + struct device *dev = this->dev; + + if (virt_addr_valid(source)) { + dma_addr_t source_phys; + + source_phys = dma_map_single(dev, (void *)source, length, + DMA_TO_DEVICE); + if (dma_mapping_error(dev, source_phys)) { + if (alt_size < length) { + dev_err(dev, "Alternate buffer is too small\n"); + return -ENOMEM; + } + goto map_failed; + } + *use_virt = source; + *use_phys = source_phys; + return 0; + } +map_failed: + /* + * Copy the content of the source buffer into the alternate + * buffer and set up the return values accordingly. + */ + memcpy(alt_virt, source, length); + + *use_virt = alt_virt; + *use_phys = alt_phys; + return 0; +} + +static void send_page_end(struct gpmi_nand_data *this, + const void *source, unsigned length, + void *alt_virt, dma_addr_t alt_phys, unsigned alt_size, + const void *used_virt, dma_addr_t used_phys) +{ + struct device *dev = this->dev; + if (used_virt == source) + dma_unmap_single(dev, used_phys, length, DMA_TO_DEVICE); +} + +static void gpmi_free_dma_buffer(struct gpmi_nand_data *this) +{ + struct device *dev = this->dev; + + if (this->page_buffer_virt && virt_addr_valid(this->page_buffer_virt)) + dma_free_coherent(dev, this->page_buffer_size, + this->page_buffer_virt, + this->page_buffer_phys); + kfree(this->cmd_buffer); + kfree(this->data_buffer_dma); + kfree(this->raw_buffer); + + this->cmd_buffer = NULL; + this->data_buffer_dma = NULL; + this->page_buffer_virt = NULL; + this->page_buffer_size = 0; +} + +/* Allocate the DMA buffers */ +static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this) +{ + struct bch_geometry *geo = &this->bch_geometry; + struct device *dev = this->dev; + struct mtd_info *mtd = &this->mtd; + + /* [1] Allocate a command buffer. PAGE_SIZE is enough. */ + this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA | GFP_KERNEL); + if (this->cmd_buffer == NULL) + goto error_alloc; + + /* + * [2] Allocate a read/write data buffer. + * The gpmi_alloc_dma_buffer can be called twice. + * We allocate a PAGE_SIZE length buffer if gpmi_alloc_dma_buffer + * is called before the nand_scan_ident; and we allocate a buffer + * of the real NAND page size when the gpmi_alloc_dma_buffer is + * called after the nand_scan_ident. + */ + this->data_buffer_dma = kzalloc(mtd->writesize ?: PAGE_SIZE, + GFP_DMA | GFP_KERNEL); + if (this->data_buffer_dma == NULL) + goto error_alloc; + + /* + * [3] Allocate the page buffer. + * + * Both the payload buffer and the auxiliary buffer must appear on + * 32-bit boundaries. We presume the size of the payload buffer is a + * power of two and is much larger than four, which guarantees the + * auxiliary buffer will appear on a 32-bit boundary. + */ + this->page_buffer_size = geo->payload_size + geo->auxiliary_size; + this->page_buffer_virt = dma_alloc_coherent(dev, this->page_buffer_size, + &this->page_buffer_phys, GFP_DMA); + if (!this->page_buffer_virt) + goto error_alloc; + + this->raw_buffer = kzalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); + if (!this->raw_buffer) + goto error_alloc; + + /* Slice up the page buffer. */ + this->payload_virt = this->page_buffer_virt; + this->payload_phys = this->page_buffer_phys; + this->auxiliary_virt = this->payload_virt + geo->payload_size; + this->auxiliary_phys = this->payload_phys + geo->payload_size; + return 0; + +error_alloc: + gpmi_free_dma_buffer(this); + return -ENOMEM; +} + +static void gpmi_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + int ret; + + /* + * Every operation begins with a command byte and a series of zero or + * more address bytes. These are distinguished by either the Address + * Latch Enable (ALE) or Command Latch Enable (CLE) signals being + * asserted. When MTD is ready to execute the command, it will deassert + * both latch enables. + * + * Rather than run a separate DMA operation for every single byte, we + * queue them up and run a single DMA operation for the entire series + * of command and data bytes. NAND_CMD_NONE means the END of the queue. + */ + if ((ctrl & (NAND_ALE | NAND_CLE))) { + if (data != NAND_CMD_NONE) + this->cmd_buffer[this->command_length++] = data; + return; + } + + if (!this->command_length) + return; + + ret = gpmi_send_command(this); + if (ret) + dev_err(this->dev, "Chip: %u, Error %d\n", + this->current_chip, ret); + + this->command_length = 0; +} + +static int gpmi_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + + return gpmi_is_ready(this, this->current_chip); +} + +static void gpmi_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + + if ((this->current_chip < 0) && (chipnr >= 0)) + gpmi_begin(this); + else if ((this->current_chip >= 0) && (chipnr < 0)) + gpmi_end(this); + + this->current_chip = chipnr; +} + +static void gpmi_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + + dev_dbg(this->dev, "len is %d\n", len); + this->upper_buf = buf; + this->upper_len = len; + + gpmi_read_data(this); +} + +static void gpmi_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + + dev_dbg(this->dev, "len is %d\n", len); + this->upper_buf = (uint8_t *)buf; + this->upper_len = len; + + gpmi_send_data(this); +} + +static uint8_t gpmi_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + uint8_t *buf = this->data_buffer_dma; + + gpmi_read_buf(mtd, buf, 1); + return buf[0]; +} + +/* + * Handles block mark swapping. + * It can be called in swapping the block mark, or swapping it back, + * because the the operations are the same. + */ +static void block_mark_swapping(struct gpmi_nand_data *this, + void *payload, void *auxiliary) +{ + struct bch_geometry *nfc_geo = &this->bch_geometry; + unsigned char *p; + unsigned char *a; + unsigned int bit; + unsigned char mask; + unsigned char from_data; + unsigned char from_oob; + + if (!this->swap_block_mark) + return; + + /* + * If control arrives here, we're swapping. Make some convenience + * variables. + */ + bit = nfc_geo->block_mark_bit_offset; + p = payload + nfc_geo->block_mark_byte_offset; + a = auxiliary; + + /* + * Get the byte from the data area that overlays the block mark. Since + * the ECC engine applies its own view to the bits in the page, the + * physical block mark won't (in general) appear on a byte boundary in + * the data. + */ + from_data = (p[0] >> bit) | (p[1] << (8 - bit)); + + /* Get the byte from the OOB. */ + from_oob = a[0]; + + /* Swap them. */ + a[0] = from_data; + + mask = (0x1 << bit) - 1; + p[0] = (p[0] & mask) | (from_oob << bit); + + mask = ~0 << bit; + p[1] = (p[1] & mask) | (from_oob >> (8 - bit)); +} + +static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct gpmi_nand_data *this = chip->priv; + struct bch_geometry *nfc_geo = &this->bch_geometry; + void *payload_virt; + dma_addr_t payload_phys; + void *auxiliary_virt; + dma_addr_t auxiliary_phys; + unsigned int i; + unsigned char *status; + unsigned int max_bitflips = 0; + int ret; + + dev_dbg(this->dev, "page number is : %d\n", page); + ret = read_page_prepare(this, buf, nfc_geo->payload_size, + this->payload_virt, this->payload_phys, + nfc_geo->payload_size, + &payload_virt, &payload_phys); + if (ret) { + dev_err(this->dev, "Inadequate DMA buffer\n"); + ret = -ENOMEM; + return ret; + } + auxiliary_virt = this->auxiliary_virt; + auxiliary_phys = this->auxiliary_phys; + + /* go! */ + ret = gpmi_read_page(this, payload_phys, auxiliary_phys); + read_page_end(this, buf, nfc_geo->payload_size, + this->payload_virt, this->payload_phys, + nfc_geo->payload_size, + payload_virt, payload_phys); + if (ret) { + dev_err(this->dev, "Error in ECC-based read: %d\n", ret); + return ret; + } + + /* handle the block mark swapping */ + block_mark_swapping(this, payload_virt, auxiliary_virt); + + /* Loop over status bytes, accumulating ECC status. */ + status = auxiliary_virt + nfc_geo->auxiliary_status_offset; + + for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) { + if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED)) + continue; + + if (*status == STATUS_UNCORRECTABLE) { + mtd->ecc_stats.failed++; + continue; + } + mtd->ecc_stats.corrected += *status; + max_bitflips = max_t(unsigned int, max_bitflips, *status); + } + + if (oob_required) { + /* + * It's time to deliver the OOB bytes. See gpmi_ecc_read_oob() + * for details about our policy for delivering the OOB. + * + * We fill the caller's buffer with set bits, and then copy the + * block mark to th caller's buffer. Note that, if block mark + * swapping was necessary, it has already been done, so we can + * rely on the first byte of the auxiliary buffer to contain + * the block mark. + */ + memset(chip->oob_poi, ~0, mtd->oobsize); + chip->oob_poi[0] = ((uint8_t *) auxiliary_virt)[0]; + } + + read_page_swap_end(this, buf, nfc_geo->payload_size, + this->payload_virt, this->payload_phys, + nfc_geo->payload_size, + payload_virt, payload_phys); + + return max_bitflips; +} + +/* Fake a virtual small page for the subpage read */ +static int gpmi_ecc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offs, uint32_t len, uint8_t *buf, int page) +{ + struct gpmi_nand_data *this = chip->priv; + void __iomem *bch_regs = this->resources.bch_regs; + struct bch_geometry old_geo = this->bch_geometry; + struct bch_geometry *geo = &this->bch_geometry; + int size = chip->ecc.size; /* ECC chunk size */ + int meta, n, page_size; + u32 r1_old, r2_old, r1_new, r2_new; + unsigned int max_bitflips; + int first, last, marker_pos; + int ecc_parity_size; + int col = 0; + int old_swap_block_mark = this->swap_block_mark; + + /* The size of ECC parity */ + ecc_parity_size = geo->gf_len * geo->ecc_strength / 8; + + /* Align it with the chunk size */ + first = offs / size; + last = (offs + len - 1) / size; + + if (this->swap_block_mark) { + /* + * Find the chunk which contains the Block Marker. + * If this chunk is in the range of [first, last], + * we have to read out the whole page. + * Why? since we had swapped the data at the position of Block + * Marker to the metadata which is bound with the chunk 0. + */ + marker_pos = geo->block_mark_byte_offset / size; + if (last >= marker_pos && first <= marker_pos) { + dev_dbg(this->dev, + "page:%d, first:%d, last:%d, marker at:%d\n", + page, first, last, marker_pos); + return gpmi_ecc_read_page(mtd, chip, buf, 0, page); + } + } + + meta = geo->metadata_size; + if (first) { + col = meta + (size + ecc_parity_size) * first; + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, col, -1); + + meta = 0; + buf = buf + first * size; + } + + /* Save the old environment */ + r1_old = r1_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT0); + r2_old = r2_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT1); + + /* change the BCH registers and bch_geometry{} */ + n = last - first + 1; + page_size = meta + (size + ecc_parity_size) * n; + + r1_new &= ~(BM_BCH_FLASH0LAYOUT0_NBLOCKS | + BM_BCH_FLASH0LAYOUT0_META_SIZE); + r1_new |= BF_BCH_FLASH0LAYOUT0_NBLOCKS(n - 1) + | BF_BCH_FLASH0LAYOUT0_META_SIZE(meta); + writel(r1_new, bch_regs + HW_BCH_FLASH0LAYOUT0); + + r2_new &= ~BM_BCH_FLASH0LAYOUT1_PAGE_SIZE; + r2_new |= BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size); + writel(r2_new, bch_regs + HW_BCH_FLASH0LAYOUT1); + + geo->ecc_chunk_count = n; + geo->payload_size = n * size; + geo->page_size = page_size; + geo->auxiliary_status_offset = ALIGN(meta, 4); + + dev_dbg(this->dev, "page:%d(%d:%d)%d, chunk:(%d:%d), BCH PG size:%d\n", + page, offs, len, col, first, n, page_size); + + /* Read the subpage now */ + this->swap_block_mark = false; + max_bitflips = gpmi_ecc_read_page(mtd, chip, buf, 0, page); + + /* Restore */ + writel(r1_old, bch_regs + HW_BCH_FLASH0LAYOUT0); + writel(r2_old, bch_regs + HW_BCH_FLASH0LAYOUT1); + this->bch_geometry = old_geo; + this->swap_block_mark = old_swap_block_mark; + + return max_bitflips; +} + +static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + struct gpmi_nand_data *this = chip->priv; + struct bch_geometry *nfc_geo = &this->bch_geometry; + const void *payload_virt; + dma_addr_t payload_phys; + const void *auxiliary_virt; + dma_addr_t auxiliary_phys; + int ret; + + dev_dbg(this->dev, "ecc write page.\n"); + if (this->swap_block_mark) { + /* + * If control arrives here, we're doing block mark swapping. + * Since we can't modify the caller's buffers, we must copy them + * into our own. + */ + memcpy(this->payload_virt, buf, mtd->writesize); + payload_virt = this->payload_virt; + payload_phys = this->payload_phys; + + memcpy(this->auxiliary_virt, chip->oob_poi, + nfc_geo->auxiliary_size); + auxiliary_virt = this->auxiliary_virt; + auxiliary_phys = this->auxiliary_phys; + + /* Handle block mark swapping. */ + block_mark_swapping(this, + (void *)payload_virt, (void *)auxiliary_virt); + } else { + /* + * If control arrives here, we're not doing block mark swapping, + * so we can to try and use the caller's buffers. + */ + ret = send_page_prepare(this, + buf, mtd->writesize, + this->payload_virt, this->payload_phys, + nfc_geo->payload_size, + &payload_virt, &payload_phys); + if (ret) { + dev_err(this->dev, "Inadequate payload DMA buffer\n"); + return 0; + } + + ret = send_page_prepare(this, + chip->oob_poi, mtd->oobsize, + this->auxiliary_virt, this->auxiliary_phys, + nfc_geo->auxiliary_size, + &auxiliary_virt, &auxiliary_phys); + if (ret) { + dev_err(this->dev, "Inadequate auxiliary DMA buffer\n"); + goto exit_auxiliary; + } + } + + /* Ask the NFC. */ + ret = gpmi_send_page(this, payload_phys, auxiliary_phys); + if (ret) + dev_err(this->dev, "Error in ECC-based write: %d\n", ret); + + if (!this->swap_block_mark) { + send_page_end(this, chip->oob_poi, mtd->oobsize, + this->auxiliary_virt, this->auxiliary_phys, + nfc_geo->auxiliary_size, + auxiliary_virt, auxiliary_phys); +exit_auxiliary: + send_page_end(this, buf, mtd->writesize, + this->payload_virt, this->payload_phys, + nfc_geo->payload_size, + payload_virt, payload_phys); + } + + return 0; +} + +/* + * There are several places in this driver where we have to handle the OOB and + * block marks. This is the function where things are the most complicated, so + * this is where we try to explain it all. All the other places refer back to + * here. + * + * These are the rules, in order of decreasing importance: + * + * 1) Nothing the caller does can be allowed to imperil the block mark. + * + * 2) In read operations, the first byte of the OOB we return must reflect the + * true state of the block mark, no matter where that block mark appears in + * the physical page. + * + * 3) ECC-based read operations return an OOB full of set bits (since we never + * allow ECC-based writes to the OOB, it doesn't matter what ECC-based reads + * return). + * + * 4) "Raw" read operations return a direct view of the physical bytes in the + * page, using the conventional definition of which bytes are data and which + * are OOB. This gives the caller a way to see the actual, physical bytes + * in the page, without the distortions applied by our ECC engine. + * + * + * What we do for this specific read operation depends on two questions: + * + * 1) Are we doing a "raw" read, or an ECC-based read? + * + * 2) Are we using block mark swapping or transcription? + * + * There are four cases, illustrated by the following Karnaugh map: + * + * | Raw | ECC-based | + * -------------+-------------------------+-------------------------+ + * | Read the conventional | | + * | OOB at the end of the | | + * Swapping | page and return it. It | | + * | contains exactly what | | + * | we want. | Read the block mark and | + * -------------+-------------------------+ return it in a buffer | + * | Read the conventional | full of set bits. | + * | OOB at the end of the | | + * | page and also the block | | + * Transcribing | mark in the metadata. | | + * | Copy the block mark | | + * | into the first byte of | | + * | the OOB. | | + * -------------+-------------------------+-------------------------+ + * + * Note that we break rule #4 in the Transcribing/Raw case because we're not + * giving an accurate view of the actual, physical bytes in the page (we're + * overwriting the block mark). That's OK because it's more important to follow + * rule #2. + * + * It turns out that knowing whether we want an "ECC-based" or "raw" read is not + * easy. When reading a page, for example, the NAND Flash MTD code calls our + * ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an + * ECC-based or raw view of the page is implicit in which function it calls + * (there is a similar pair of ECC-based/raw functions for writing). + */ +static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + struct gpmi_nand_data *this = chip->priv; + + dev_dbg(this->dev, "page number is %d\n", page); + /* clear the OOB buffer */ + memset(chip->oob_poi, ~0, mtd->oobsize); + + /* Read out the conventional OOB. */ + chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + /* + * Now, we want to make sure the block mark is correct. In the + * non-transcribing case (!GPMI_IS_MX23()), we already have it. + * Otherwise, we need to explicitly read it. + */ + if (GPMI_IS_MX23(this)) { + /* Read the block mark into the first byte of the OOB buffer. */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + chip->oob_poi[0] = chip->read_byte(mtd); + } + + return 0; +} + +static int +gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) +{ + struct nand_oobfree *of = mtd->ecclayout->oobfree; + int status = 0; + + /* Do we have available oob area? */ + if (!of->length) + return -EPERM; + + if (!nand_is_slc(chip)) + return -EPERM; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of->offset, page); + chip->write_buf(mtd, chip->oob_poi + of->offset, of->length); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/* + * This function reads a NAND page without involving the ECC engine (no HW + * ECC correction). + * The tricky part in the GPMI/BCH controller is that it stores ECC bits + * inline (interleaved with payload DATA), and do not align data chunk on + * byte boundaries. + * We thus need to take care moving the payload data and ECC bits stored in the + * page into the provided buffers, which is why we're using gpmi_copy_bits. + * + * See set_geometry_by_ecc_info inline comments to have a full description + * of the layout used by the GPMI controller. + */ +static int gpmi_ecc_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + struct gpmi_nand_data *this = chip->priv; + struct bch_geometry *nfc_geo = &this->bch_geometry; + int eccsize = nfc_geo->ecc_chunk_size; + int eccbits = nfc_geo->ecc_strength * nfc_geo->gf_len; + u8 *tmp_buf = this->raw_buffer; + size_t src_bit_off; + size_t oob_bit_off; + size_t oob_byte_off; + uint8_t *oob = chip->oob_poi; + int step; + + chip->read_buf(mtd, tmp_buf, + mtd->writesize + mtd->oobsize); + + /* + * If required, swap the bad block marker and the data stored in the + * metadata section, so that we don't wrongly consider a block as bad. + * + * See the layout description for a detailed explanation on why this + * is needed. + */ + if (this->swap_block_mark) { + u8 swap = tmp_buf[0]; + + tmp_buf[0] = tmp_buf[mtd->writesize]; + tmp_buf[mtd->writesize] = swap; + } + + /* + * Copy the metadata section into the oob buffer (this section is + * guaranteed to be aligned on a byte boundary). + */ + if (oob_required) + memcpy(oob, tmp_buf, nfc_geo->metadata_size); + + oob_bit_off = nfc_geo->metadata_size * 8; + src_bit_off = oob_bit_off; + + /* Extract interleaved payload data and ECC bits */ + for (step = 0; step < nfc_geo->ecc_chunk_count; step++) { + if (buf) + gpmi_copy_bits(buf, step * eccsize * 8, + tmp_buf, src_bit_off, + eccsize * 8); + src_bit_off += eccsize * 8; + + /* Align last ECC block to align a byte boundary */ + if (step == nfc_geo->ecc_chunk_count - 1 && + (oob_bit_off + eccbits) % 8) + eccbits += 8 - ((oob_bit_off + eccbits) % 8); + + if (oob_required) + gpmi_copy_bits(oob, oob_bit_off, + tmp_buf, src_bit_off, + eccbits); + + src_bit_off += eccbits; + oob_bit_off += eccbits; + } + + if (oob_required) { + oob_byte_off = oob_bit_off / 8; + + if (oob_byte_off < mtd->oobsize) + memcpy(oob + oob_byte_off, + tmp_buf + mtd->writesize + oob_byte_off, + mtd->oobsize - oob_byte_off); + } + + return 0; +} + +/* + * This function writes a NAND page without involving the ECC engine (no HW + * ECC generation). + * The tricky part in the GPMI/BCH controller is that it stores ECC bits + * inline (interleaved with payload DATA), and do not align data chunk on + * byte boundaries. + * We thus need to take care moving the OOB area at the right place in the + * final page, which is why we're using gpmi_copy_bits. + * + * See set_geometry_by_ecc_info inline comments to have a full description + * of the layout used by the GPMI controller. + */ +static int gpmi_ecc_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, + int oob_required) +{ + struct gpmi_nand_data *this = chip->priv; + struct bch_geometry *nfc_geo = &this->bch_geometry; + int eccsize = nfc_geo->ecc_chunk_size; + int eccbits = nfc_geo->ecc_strength * nfc_geo->gf_len; + u8 *tmp_buf = this->raw_buffer; + uint8_t *oob = chip->oob_poi; + size_t dst_bit_off; + size_t oob_bit_off; + size_t oob_byte_off; + int step; + + /* + * Initialize all bits to 1 in case we don't have a buffer for the + * payload or oob data in order to leave unspecified bits of data + * to their initial state. + */ + if (!buf || !oob_required) + memset(tmp_buf, 0xff, mtd->writesize + mtd->oobsize); + + /* + * First copy the metadata section (stored in oob buffer) at the + * beginning of the page, as imposed by the GPMI layout. + */ + memcpy(tmp_buf, oob, nfc_geo->metadata_size); + oob_bit_off = nfc_geo->metadata_size * 8; + dst_bit_off = oob_bit_off; + + /* Interleave payload data and ECC bits */ + for (step = 0; step < nfc_geo->ecc_chunk_count; step++) { + if (buf) + gpmi_copy_bits(tmp_buf, dst_bit_off, + buf, step * eccsize * 8, eccsize * 8); + dst_bit_off += eccsize * 8; + + /* Align last ECC block to align a byte boundary */ + if (step == nfc_geo->ecc_chunk_count - 1 && + (oob_bit_off + eccbits) % 8) + eccbits += 8 - ((oob_bit_off + eccbits) % 8); + + if (oob_required) + gpmi_copy_bits(tmp_buf, dst_bit_off, + oob, oob_bit_off, eccbits); + + dst_bit_off += eccbits; + oob_bit_off += eccbits; + } + + oob_byte_off = oob_bit_off / 8; + + if (oob_required && oob_byte_off < mtd->oobsize) + memcpy(tmp_buf + mtd->writesize + oob_byte_off, + oob + oob_byte_off, mtd->oobsize - oob_byte_off); + + /* + * If required, swap the bad block marker and the first byte of the + * metadata section, so that we don't modify the bad block marker. + * + * See the layout description for a detailed explanation on why this + * is needed. + */ + if (this->swap_block_mark) { + u8 swap = tmp_buf[0]; + + tmp_buf[0] = tmp_buf[mtd->writesize]; + tmp_buf[mtd->writesize] = swap; + } + + chip->write_buf(mtd, tmp_buf, mtd->writesize + mtd->oobsize); + + return 0; +} + +static int gpmi_ecc_read_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + return gpmi_ecc_read_page_raw(mtd, chip, NULL, 1, page); +} + +static int gpmi_ecc_write_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0, page); + + return gpmi_ecc_write_page_raw(mtd, chip, NULL, 1); +} + +static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd->priv; + struct gpmi_nand_data *this = chip->priv; + int ret = 0; + uint8_t *block_mark; + int column, page, status, chipnr; + + chipnr = (int)(ofs >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + column = !GPMI_IS_MX23(this) ? mtd->writesize : 0; + + /* Write the block mark. */ + block_mark = this->data_buffer_dma; + block_mark[0] = 0; /* bad block marker */ + + /* Shift to get page */ + page = (int)(ofs >> chip->page_shift); + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, column, page); + chip->write_buf(mtd, block_mark, 1); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + ret = -EIO; + + chip->select_chip(mtd, -1); + + return ret; +} + +static int nand_boot_set_geometry(struct gpmi_nand_data *this) +{ + struct boot_rom_geometry *geometry = &this->rom_geometry; + + /* + * Set the boot block stride size. + * + * In principle, we should be reading this from the OTP bits, since + * that's where the ROM is going to get it. In fact, we don't have any + * way to read the OTP bits, so we go with the default and hope for the + * best. + */ + geometry->stride_size_in_pages = 64; + + /* + * Set the search area stride exponent. + * + * In principle, we should be reading this from the OTP bits, since + * that's where the ROM is going to get it. In fact, we don't have any + * way to read the OTP bits, so we go with the default and hope for the + * best. + */ + geometry->search_area_stride_exponent = 2; + return 0; +} + +static const char *fingerprint = "STMP"; +static int mx23_check_transcription_stamp(struct gpmi_nand_data *this) +{ + struct boot_rom_geometry *rom_geo = &this->rom_geometry; + struct device *dev = this->dev; + struct mtd_info *mtd = &this->mtd; + struct nand_chip *chip = &this->nand; + unsigned int search_area_size_in_strides; + unsigned int stride; + unsigned int page; + uint8_t *buffer = chip->buffers->databuf; + int saved_chip_number; + int found_an_ncb_fingerprint = false; + + /* Compute the number of strides in a search area. */ + search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent; + + saved_chip_number = this->current_chip; + chip->select_chip(mtd, 0); + + /* + * Loop through the first search area, looking for the NCB fingerprint. + */ + dev_dbg(dev, "Scanning for an NCB fingerprint...\n"); + + for (stride = 0; stride < search_area_size_in_strides; stride++) { + /* Compute the page addresses. */ + page = stride * rom_geo->stride_size_in_pages; + + dev_dbg(dev, "Looking for a fingerprint in page 0x%x\n", page); + + /* + * Read the NCB fingerprint. The fingerprint is four bytes long + * and starts in the 12th byte of the page. + */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 12, page); + chip->read_buf(mtd, buffer, strlen(fingerprint)); + + /* Look for the fingerprint. */ + if (!memcmp(buffer, fingerprint, strlen(fingerprint))) { + found_an_ncb_fingerprint = true; + break; + } + + } + + chip->select_chip(mtd, saved_chip_number); + + if (found_an_ncb_fingerprint) + dev_dbg(dev, "\tFound a fingerprint\n"); + else + dev_dbg(dev, "\tNo fingerprint found\n"); + return found_an_ncb_fingerprint; +} + +/* Writes a transcription stamp. */ +static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) +{ + struct device *dev = this->dev; + struct boot_rom_geometry *rom_geo = &this->rom_geometry; + struct mtd_info *mtd = &this->mtd; + struct nand_chip *chip = &this->nand; + unsigned int block_size_in_pages; + unsigned int search_area_size_in_strides; + unsigned int search_area_size_in_pages; + unsigned int search_area_size_in_blocks; + unsigned int block; + unsigned int stride; + unsigned int page; + uint8_t *buffer = chip->buffers->databuf; + int saved_chip_number; + int status; + + /* Compute the search area geometry. */ + block_size_in_pages = mtd->erasesize / mtd->writesize; + search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent; + search_area_size_in_pages = search_area_size_in_strides * + rom_geo->stride_size_in_pages; + search_area_size_in_blocks = + (search_area_size_in_pages + (block_size_in_pages - 1)) / + block_size_in_pages; + + dev_dbg(dev, "Search Area Geometry :\n"); + dev_dbg(dev, "\tin Blocks : %u\n", search_area_size_in_blocks); + dev_dbg(dev, "\tin Strides: %u\n", search_area_size_in_strides); + dev_dbg(dev, "\tin Pages : %u\n", search_area_size_in_pages); + + /* Select chip 0. */ + saved_chip_number = this->current_chip; + chip->select_chip(mtd, 0); + + /* Loop over blocks in the first search area, erasing them. */ + dev_dbg(dev, "Erasing the search area...\n"); + + for (block = 0; block < search_area_size_in_blocks; block++) { + /* Compute the page address. */ + page = block * block_size_in_pages; + + /* Erase this block. */ + dev_dbg(dev, "\tErasing block 0x%x\n", block); + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + + /* Wait for the erase to finish. */ + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + dev_err(dev, "[%s] Erase failed.\n", __func__); + } + + /* Write the NCB fingerprint into the page buffer. */ + memset(buffer, ~0, mtd->writesize); + memcpy(buffer + 12, fingerprint, strlen(fingerprint)); + + /* Loop through the first search area, writing NCB fingerprints. */ + dev_dbg(dev, "Writing NCB fingerprints...\n"); + for (stride = 0; stride < search_area_size_in_strides; stride++) { + /* Compute the page addresses. */ + page = stride * rom_geo->stride_size_in_pages; + + /* Write the first page of the current stride. */ + dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page); + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + chip->ecc.write_page_raw(mtd, chip, buffer, 0); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + /* Wait for the write to finish. */ + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + dev_err(dev, "[%s] Write failed.\n", __func__); + } + + /* Deselect chip 0. */ + chip->select_chip(mtd, saved_chip_number); + return 0; +} + +static int mx23_boot_init(struct gpmi_nand_data *this) +{ + struct device *dev = this->dev; + struct nand_chip *chip = &this->nand; + struct mtd_info *mtd = &this->mtd; + unsigned int block_count; + unsigned int block; + int chipnr; + int page; + loff_t byte; + uint8_t block_mark; + int ret = 0; + + /* + * If control arrives here, we can't use block mark swapping, which + * means we're forced to use transcription. First, scan for the + * transcription stamp. If we find it, then we don't have to do + * anything -- the block marks are already transcribed. + */ + if (mx23_check_transcription_stamp(this)) + return 0; + + /* + * If control arrives here, we couldn't find a transcription stamp, so + * so we presume the block marks are in the conventional location. + */ + dev_dbg(dev, "Transcribing bad block marks...\n"); + + /* Compute the number of blocks in the entire medium. */ + block_count = chip->chipsize >> chip->phys_erase_shift; + + /* + * Loop over all the blocks in the medium, transcribing block marks as + * we go. + */ + for (block = 0; block < block_count; block++) { + /* + * Compute the chip, page and byte addresses for this block's + * conventional mark. + */ + chipnr = block >> (chip->chip_shift - chip->phys_erase_shift); + page = block << (chip->phys_erase_shift - chip->page_shift); + byte = block << chip->phys_erase_shift; + + /* Send the command to read the conventional block mark. */ + chip->select_chip(mtd, chipnr); + chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); + block_mark = chip->read_byte(mtd); + chip->select_chip(mtd, -1); + + /* + * Check if the block is marked bad. If so, we need to mark it + * again, but this time the result will be a mark in the + * location where we transcribe block marks. + */ + if (block_mark != 0xff) { + dev_dbg(dev, "Transcribing mark in block %u\n", block); + ret = chip->block_markbad(mtd, byte); + if (ret) + dev_err(dev, + "Failed to mark block bad with ret %d\n", + ret); + } + } + + /* Write the stamp that indicates we've transcribed the block marks. */ + mx23_write_transcription_stamp(this); + return 0; +} + +static int nand_boot_init(struct gpmi_nand_data *this) +{ + nand_boot_set_geometry(this); + + /* This is ROM arch-specific initilization before the BBT scanning. */ + if (GPMI_IS_MX23(this)) + return mx23_boot_init(this); + return 0; +} + +static int gpmi_set_geometry(struct gpmi_nand_data *this) +{ + int ret; + + /* Free the temporary DMA memory for reading ID. */ + gpmi_free_dma_buffer(this); + + /* Set up the NFC geometry which is used by BCH. */ + ret = bch_set_geometry(this); + if (ret) { + dev_err(this->dev, "Error setting BCH geometry : %d\n", ret); + return ret; + } + + /* Alloc the new DMA buffers according to the pagesize and oobsize */ + return gpmi_alloc_dma_buffer(this); +} + +static void gpmi_nand_exit(struct gpmi_nand_data *this) +{ + nand_release(&this->mtd); + gpmi_free_dma_buffer(this); +} + +static int gpmi_init_last(struct gpmi_nand_data *this) +{ + struct mtd_info *mtd = &this->mtd; + struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct bch_geometry *bch_geo = &this->bch_geometry; + int ret; + + /* Set up the medium geometry */ + ret = gpmi_set_geometry(this); + if (ret) + return ret; + + /* Init the nand_ecc_ctrl{} */ + ecc->read_page = gpmi_ecc_read_page; + ecc->write_page = gpmi_ecc_write_page; + ecc->read_oob = gpmi_ecc_read_oob; + ecc->write_oob = gpmi_ecc_write_oob; + ecc->read_page_raw = gpmi_ecc_read_page_raw; + ecc->write_page_raw = gpmi_ecc_write_page_raw; + ecc->read_oob_raw = gpmi_ecc_read_oob_raw; + ecc->write_oob_raw = gpmi_ecc_write_oob_raw; + ecc->mode = NAND_ECC_HW; + ecc->size = bch_geo->ecc_chunk_size; + ecc->strength = bch_geo->ecc_strength; + ecc->layout = &gpmi_hw_ecclayout; + + /* + * We only enable the subpage read when: + * (1) the chip is imx6, and + * (2) the size of the ECC parity is byte aligned. + */ + if (GPMI_IS_MX6(this) && + ((bch_geo->gf_len * bch_geo->ecc_strength) % 8) == 0) { + ecc->read_subpage = gpmi_ecc_read_subpage; + chip->options |= NAND_SUBPAGE_READ; + } + + /* + * Can we enable the extra features? such as EDO or Sync mode. + * + * We do not check the return value now. That's means if we fail in + * enable the extra features, we still can run in the normal way. + */ + gpmi_extra_init(this); + + return 0; +} + +static int gpmi_nand_init(struct gpmi_nand_data *this) +{ + struct mtd_info *mtd = &this->mtd; + struct nand_chip *chip = &this->nand; + struct mtd_part_parser_data ppdata = {}; + int ret; + + /* init current chip */ + this->current_chip = -1; + + /* init the MTD data structures */ + mtd->priv = chip; + mtd->name = "gpmi-nand"; + mtd->owner = THIS_MODULE; + + /* init the nand_chip{}, we don't support a 16-bit NAND Flash bus. */ + chip->priv = this; + chip->select_chip = gpmi_select_chip; + chip->cmd_ctrl = gpmi_cmd_ctrl; + chip->dev_ready = gpmi_dev_ready; + chip->read_byte = gpmi_read_byte; + chip->read_buf = gpmi_read_buf; + chip->write_buf = gpmi_write_buf; + chip->badblock_pattern = &gpmi_bbt_descr; + chip->block_markbad = gpmi_block_markbad; + chip->options |= NAND_NO_SUBPAGE_WRITE; + + /* Set up swap_block_mark, must be set before the gpmi_set_geometry() */ + this->swap_block_mark = !GPMI_IS_MX23(this); + + if (of_get_nand_on_flash_bbt(this->dev->of_node)) { + chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; + + if (of_property_read_bool(this->dev->of_node, + "fsl,no-blockmark-swap")) + this->swap_block_mark = false; + } + dev_dbg(this->dev, "Blockmark swapping %sabled\n", + this->swap_block_mark ? "en" : "dis"); + + /* + * Allocate a temporary DMA buffer for reading ID in the + * nand_scan_ident(). + */ + this->bch_geometry.payload_size = 1024; + this->bch_geometry.auxiliary_size = 128; + ret = gpmi_alloc_dma_buffer(this); + if (ret) + goto err_out; + + ret = nand_scan_ident(mtd, GPMI_IS_MX6(this) ? 2 : 1, NULL); + if (ret) + goto err_out; + + ret = gpmi_init_last(this); + if (ret) + goto err_out; + + chip->options |= NAND_SKIP_BBTSCAN; + ret = nand_scan_tail(mtd); + if (ret) + goto err_out; + + ret = nand_boot_init(this); + if (ret) + goto err_out; + ret = chip->scan_bbt(mtd); + if (ret) + goto err_out; + + ppdata.of_node = this->pdev->dev.of_node; + ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (ret) + goto err_out; + return 0; + +err_out: + gpmi_nand_exit(this); + return ret; +} + +static const struct of_device_id gpmi_nand_id_table[] = { + { + .compatible = "fsl,imx23-gpmi-nand", + .data = &gpmi_devdata_imx23, + }, { + .compatible = "fsl,imx28-gpmi-nand", + .data = &gpmi_devdata_imx28, + }, { + .compatible = "fsl,imx6q-gpmi-nand", + .data = &gpmi_devdata_imx6q, + }, { + .compatible = "fsl,imx6sx-gpmi-nand", + .data = &gpmi_devdata_imx6sx, + }, {} +}; +MODULE_DEVICE_TABLE(of, gpmi_nand_id_table); + +static int gpmi_nand_probe(struct platform_device *pdev) +{ + struct gpmi_nand_data *this; + const struct of_device_id *of_id; + int ret; + + this = devm_kzalloc(&pdev->dev, sizeof(*this), GFP_KERNEL); + if (!this) + return -ENOMEM; + + of_id = of_match_device(gpmi_nand_id_table, &pdev->dev); + if (of_id) { + this->devdata = of_id->data; + } else { + dev_err(&pdev->dev, "Failed to find the right device id.\n"); + return -ENODEV; + } + + platform_set_drvdata(pdev, this); + this->pdev = pdev; + this->dev = &pdev->dev; + + ret = acquire_resources(this); + if (ret) + goto exit_acquire_resources; + + ret = init_hardware(this); + if (ret) + goto exit_nfc_init; + + ret = gpmi_nand_init(this); + if (ret) + goto exit_nfc_init; + + dev_info(this->dev, "driver registered.\n"); + + return 0; + +exit_nfc_init: + release_resources(this); +exit_acquire_resources: + + return ret; +} + +static int gpmi_nand_remove(struct platform_device *pdev) +{ + struct gpmi_nand_data *this = platform_get_drvdata(pdev); + + gpmi_nand_exit(this); + release_resources(this); + return 0; +} + +static struct platform_driver gpmi_nand_driver = { + .driver = { + .name = "gpmi-nand", + .of_match_table = gpmi_nand_id_table, + }, + .probe = gpmi_nand_probe, + .remove = gpmi_nand_remove, +}; +module_platform_driver(gpmi_nand_driver); + +MODULE_AUTHOR("Freescale Semiconductor, Inc."); +MODULE_DESCRIPTION("i.MX GPMI NAND Flash Controller Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h new file mode 100644 index 000000000..544062f65 --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h @@ -0,0 +1,311 @@ +/* + * Freescale GPMI NAND Flash Driver + * + * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. + * Copyright (C) 2008 Embedded Alley Solutions, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#ifndef __DRIVERS_MTD_NAND_GPMI_NAND_H +#define __DRIVERS_MTD_NAND_GPMI_NAND_H + +#include <linux/mtd/nand.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> + +#define GPMI_CLK_MAX 5 /* MX6Q needs five clocks */ +struct resources { + void __iomem *gpmi_regs; + void __iomem *bch_regs; + unsigned int dma_low_channel; + unsigned int dma_high_channel; + struct clk *clock[GPMI_CLK_MAX]; +}; + +/** + * struct bch_geometry - BCH geometry description. + * @gf_len: The length of Galois Field. (e.g., 13 or 14) + * @ecc_strength: A number that describes the strength of the ECC + * algorithm. + * @page_size: The size, in bytes, of a physical page, including + * both data and OOB. + * @metadata_size: The size, in bytes, of the metadata. + * @ecc_chunk_size: The size, in bytes, of a single ECC chunk. Note + * the first chunk in the page includes both data and + * metadata, so it's a bit larger than this value. + * @ecc_chunk_count: The number of ECC chunks in the page, + * @payload_size: The size, in bytes, of the payload buffer. + * @auxiliary_size: The size, in bytes, of the auxiliary buffer. + * @auxiliary_status_offset: The offset into the auxiliary buffer at which + * the ECC status appears. + * @block_mark_byte_offset: The byte offset in the ECC-based page view at + * which the underlying physical block mark appears. + * @block_mark_bit_offset: The bit offset into the ECC-based page view at + * which the underlying physical block mark appears. + */ +struct bch_geometry { + unsigned int gf_len; + unsigned int ecc_strength; + unsigned int page_size; + unsigned int metadata_size; + unsigned int ecc_chunk_size; + unsigned int ecc_chunk_count; + unsigned int payload_size; + unsigned int auxiliary_size; + unsigned int auxiliary_status_offset; + unsigned int block_mark_byte_offset; + unsigned int block_mark_bit_offset; +}; + +/** + * struct boot_rom_geometry - Boot ROM geometry description. + * @stride_size_in_pages: The size of a boot block stride, in pages. + * @search_area_stride_exponent: The logarithm to base 2 of the size of a + * search area in boot block strides. + */ +struct boot_rom_geometry { + unsigned int stride_size_in_pages; + unsigned int search_area_stride_exponent; +}; + +/* DMA operations types */ +enum dma_ops_type { + DMA_FOR_COMMAND = 1, + DMA_FOR_READ_DATA, + DMA_FOR_WRITE_DATA, + DMA_FOR_READ_ECC_PAGE, + DMA_FOR_WRITE_ECC_PAGE +}; + +/** + * struct nand_timing - Fundamental timing attributes for NAND. + * @data_setup_in_ns: The data setup time, in nanoseconds. Usually the + * maximum of tDS and tWP. A negative value + * indicates this characteristic isn't known. + * @data_hold_in_ns: The data hold time, in nanoseconds. Usually the + * maximum of tDH, tWH and tREH. A negative value + * indicates this characteristic isn't known. + * @address_setup_in_ns: The address setup time, in nanoseconds. Usually + * the maximum of tCLS, tCS and tALS. A negative + * value indicates this characteristic isn't known. + * @gpmi_sample_delay_in_ns: A GPMI-specific timing parameter. A negative value + * indicates this characteristic isn't known. + * @tREA_in_ns: tREA, in nanoseconds, from the data sheet. A + * negative value indicates this characteristic isn't + * known. + * @tRLOH_in_ns: tRLOH, in nanoseconds, from the data sheet. A + * negative value indicates this characteristic isn't + * known. + * @tRHOH_in_ns: tRHOH, in nanoseconds, from the data sheet. A + * negative value indicates this characteristic isn't + * known. + */ +struct nand_timing { + int8_t data_setup_in_ns; + int8_t data_hold_in_ns; + int8_t address_setup_in_ns; + int8_t gpmi_sample_delay_in_ns; + int8_t tREA_in_ns; + int8_t tRLOH_in_ns; + int8_t tRHOH_in_ns; +}; + +enum gpmi_type { + IS_MX23, + IS_MX28, + IS_MX6Q, + IS_MX6SX +}; + +struct gpmi_devdata { + enum gpmi_type type; + int bch_max_ecc_strength; + int max_chain_delay; /* See the async EDO mode */ +}; + +struct gpmi_nand_data { + /* flags */ +#define GPMI_ASYNC_EDO_ENABLED (1 << 0) +#define GPMI_TIMING_INIT_OK (1 << 1) + int flags; + const struct gpmi_devdata *devdata; + + /* System Interface */ + struct device *dev; + struct platform_device *pdev; + + /* Resources */ + struct resources resources; + + /* Flash Hardware */ + struct nand_timing timing; + int timing_mode; + + /* BCH */ + struct bch_geometry bch_geometry; + struct completion bch_done; + + /* NAND Boot issue */ + bool swap_block_mark; + struct boot_rom_geometry rom_geometry; + + /* MTD / NAND */ + struct nand_chip nand; + struct mtd_info mtd; + + /* General-use Variables */ + int current_chip; + unsigned int command_length; + + /* passed from upper layer */ + uint8_t *upper_buf; + int upper_len; + + /* for DMA operations */ + bool direct_dma_map_ok; + + struct scatterlist cmd_sgl; + char *cmd_buffer; + + struct scatterlist data_sgl; + char *data_buffer_dma; + + void *page_buffer_virt; + dma_addr_t page_buffer_phys; + unsigned int page_buffer_size; + + void *payload_virt; + dma_addr_t payload_phys; + + void *auxiliary_virt; + dma_addr_t auxiliary_phys; + + void *raw_buffer; + + /* DMA channels */ +#define DMA_CHANS 8 + struct dma_chan *dma_chans[DMA_CHANS]; + enum dma_ops_type last_dma_type; + enum dma_ops_type dma_type; + struct completion dma_done; + + /* private */ + void *private; +}; + +/** + * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters. + * @data_setup_in_cycles: The data setup time, in cycles. + * @data_hold_in_cycles: The data hold time, in cycles. + * @address_setup_in_cycles: The address setup time, in cycles. + * @device_busy_timeout: The timeout waiting for NAND Ready/Busy, + * this value is the number of cycles multiplied + * by 4096. + * @use_half_periods: Indicates the clock is running slowly, so the + * NFC DLL should use half-periods. + * @sample_delay_factor: The sample delay factor. + * @wrn_dly_sel: The delay on the GPMI write strobe. + */ +struct gpmi_nfc_hardware_timing { + /* for HW_GPMI_TIMING0 */ + uint8_t data_setup_in_cycles; + uint8_t data_hold_in_cycles; + uint8_t address_setup_in_cycles; + + /* for HW_GPMI_TIMING1 */ + uint16_t device_busy_timeout; +#define GPMI_DEFAULT_BUSY_TIMEOUT 0x500 /* default busy timeout value.*/ + + /* for HW_GPMI_CTRL1 */ + bool use_half_periods; + uint8_t sample_delay_factor; + uint8_t wrn_dly_sel; +}; + +/** + * struct timing_threshod - Timing threshold + * @max_data_setup_cycles: The maximum number of data setup cycles that + * can be expressed in the hardware. + * @internal_data_setup_in_ns: The time, in ns, that the NFC hardware requires + * for data read internal setup. In the Reference + * Manual, see the chapter "High-Speed NAND + * Timing" for more details. + * @max_sample_delay_factor: The maximum sample delay factor that can be + * expressed in the hardware. + * @max_dll_clock_period_in_ns: The maximum period of the GPMI clock that the + * sample delay DLL hardware can possibly work + * with (the DLL is unusable with longer periods). + * If the full-cycle period is greater than HALF + * this value, the DLL must be configured to use + * half-periods. + * @max_dll_delay_in_ns: The maximum amount of delay, in ns, that the + * DLL can implement. + * @clock_frequency_in_hz: The clock frequency, in Hz, during the current + * I/O transaction. If no I/O transaction is in + * progress, this is the clock frequency during + * the most recent I/O transaction. + */ +struct timing_threshod { + const unsigned int max_chip_count; + const unsigned int max_data_setup_cycles; + const unsigned int internal_data_setup_in_ns; + const unsigned int max_sample_delay_factor; + const unsigned int max_dll_clock_period_in_ns; + const unsigned int max_dll_delay_in_ns; + unsigned long clock_frequency_in_hz; + +}; + +/* Common Services */ +extern int common_nfc_set_geometry(struct gpmi_nand_data *); +extern struct dma_chan *get_dma_chan(struct gpmi_nand_data *); +extern void prepare_data_dma(struct gpmi_nand_data *, + enum dma_data_direction dr); +extern int start_dma_without_bch_irq(struct gpmi_nand_data *, + struct dma_async_tx_descriptor *); +extern int start_dma_with_bch_irq(struct gpmi_nand_data *, + struct dma_async_tx_descriptor *); + +/* GPMI-NAND helper function library */ +extern int gpmi_init(struct gpmi_nand_data *); +extern int gpmi_extra_init(struct gpmi_nand_data *); +extern void gpmi_clear_bch(struct gpmi_nand_data *); +extern void gpmi_dump_info(struct gpmi_nand_data *); +extern int bch_set_geometry(struct gpmi_nand_data *); +extern int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip); +extern int gpmi_send_command(struct gpmi_nand_data *); +extern void gpmi_begin(struct gpmi_nand_data *); +extern void gpmi_end(struct gpmi_nand_data *); +extern int gpmi_read_data(struct gpmi_nand_data *); +extern int gpmi_send_data(struct gpmi_nand_data *); +extern int gpmi_send_page(struct gpmi_nand_data *, + dma_addr_t payload, dma_addr_t auxiliary); +extern int gpmi_read_page(struct gpmi_nand_data *, + dma_addr_t payload, dma_addr_t auxiliary); + +void gpmi_copy_bits(u8 *dst, size_t dst_bit_off, + const u8 *src, size_t src_bit_off, + size_t nbits); + +/* BCH : Status Block Completion Codes */ +#define STATUS_GOOD 0x00 +#define STATUS_ERASED 0xff +#define STATUS_UNCORRECTABLE 0xfe + +/* Use the devdata to distinguish different Archs. */ +#define GPMI_IS_MX23(x) ((x)->devdata->type == IS_MX23) +#define GPMI_IS_MX28(x) ((x)->devdata->type == IS_MX28) +#define GPMI_IS_MX6Q(x) ((x)->devdata->type == IS_MX6Q) +#define GPMI_IS_MX6SX(x) ((x)->devdata->type == IS_MX6SX) + +#define GPMI_IS_MX6(x) (GPMI_IS_MX6Q(x) || GPMI_IS_MX6SX(x)) +#endif diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h new file mode 100644 index 000000000..82114cdc8 --- /dev/null +++ b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h @@ -0,0 +1,187 @@ +/* + * Freescale GPMI NAND Flash Driver + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008 Embedded Alley Solutions, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#ifndef __GPMI_NAND_GPMI_REGS_H +#define __GPMI_NAND_GPMI_REGS_H + +#define HW_GPMI_CTRL0 0x00000000 +#define HW_GPMI_CTRL0_SET 0x00000004 +#define HW_GPMI_CTRL0_CLR 0x00000008 +#define HW_GPMI_CTRL0_TOG 0x0000000c + +#define BP_GPMI_CTRL0_COMMAND_MODE 24 +#define BM_GPMI_CTRL0_COMMAND_MODE (3 << BP_GPMI_CTRL0_COMMAND_MODE) +#define BF_GPMI_CTRL0_COMMAND_MODE(v) \ + (((v) << BP_GPMI_CTRL0_COMMAND_MODE) & BM_GPMI_CTRL0_COMMAND_MODE) +#define BV_GPMI_CTRL0_COMMAND_MODE__WRITE 0x0 +#define BV_GPMI_CTRL0_COMMAND_MODE__READ 0x1 +#define BV_GPMI_CTRL0_COMMAND_MODE__READ_AND_COMPARE 0x2 +#define BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY 0x3 + +#define BM_GPMI_CTRL0_WORD_LENGTH (1 << 23) +#define BV_GPMI_CTRL0_WORD_LENGTH__16_BIT 0x0 +#define BV_GPMI_CTRL0_WORD_LENGTH__8_BIT 0x1 + +/* + * Difference in LOCK_CS between imx23 and imx28 : + * This bit may impact the _POWER_ consumption. So some chips + * do not set it. + */ +#define MX23_BP_GPMI_CTRL0_LOCK_CS 22 +#define MX28_BP_GPMI_CTRL0_LOCK_CS 27 +#define LOCK_CS_ENABLE 0x1 +#define BF_GPMI_CTRL0_LOCK_CS(v, x) 0x0 + +/* Difference in CS between imx23 and imx28 */ +#define BP_GPMI_CTRL0_CS 20 +#define MX23_BM_GPMI_CTRL0_CS (3 << BP_GPMI_CTRL0_CS) +#define MX28_BM_GPMI_CTRL0_CS (7 << BP_GPMI_CTRL0_CS) +#define BF_GPMI_CTRL0_CS(v, x) (((v) << BP_GPMI_CTRL0_CS) & \ + (GPMI_IS_MX23((x)) \ + ? MX23_BM_GPMI_CTRL0_CS \ + : MX28_BM_GPMI_CTRL0_CS)) + +#define BP_GPMI_CTRL0_ADDRESS 17 +#define BM_GPMI_CTRL0_ADDRESS (3 << BP_GPMI_CTRL0_ADDRESS) +#define BF_GPMI_CTRL0_ADDRESS(v) \ + (((v) << BP_GPMI_CTRL0_ADDRESS) & BM_GPMI_CTRL0_ADDRESS) +#define BV_GPMI_CTRL0_ADDRESS__NAND_DATA 0x0 +#define BV_GPMI_CTRL0_ADDRESS__NAND_CLE 0x1 +#define BV_GPMI_CTRL0_ADDRESS__NAND_ALE 0x2 + +#define BM_GPMI_CTRL0_ADDRESS_INCREMENT (1 << 16) +#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__DISABLED 0x0 +#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__ENABLED 0x1 + +#define BP_GPMI_CTRL0_XFER_COUNT 0 +#define BM_GPMI_CTRL0_XFER_COUNT (0xffff << BP_GPMI_CTRL0_XFER_COUNT) +#define BF_GPMI_CTRL0_XFER_COUNT(v) \ + (((v) << BP_GPMI_CTRL0_XFER_COUNT) & BM_GPMI_CTRL0_XFER_COUNT) + +#define HW_GPMI_COMPARE 0x00000010 + +#define HW_GPMI_ECCCTRL 0x00000020 +#define HW_GPMI_ECCCTRL_SET 0x00000024 +#define HW_GPMI_ECCCTRL_CLR 0x00000028 +#define HW_GPMI_ECCCTRL_TOG 0x0000002c + +#define BP_GPMI_ECCCTRL_ECC_CMD 13 +#define BM_GPMI_ECCCTRL_ECC_CMD (3 << BP_GPMI_ECCCTRL_ECC_CMD) +#define BF_GPMI_ECCCTRL_ECC_CMD(v) \ + (((v) << BP_GPMI_ECCCTRL_ECC_CMD) & BM_GPMI_ECCCTRL_ECC_CMD) +#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE 0x0 +#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE 0x1 + +#define BM_GPMI_ECCCTRL_ENABLE_ECC (1 << 12) +#define BV_GPMI_ECCCTRL_ENABLE_ECC__ENABLE 0x1 +#define BV_GPMI_ECCCTRL_ENABLE_ECC__DISABLE 0x0 + +#define BP_GPMI_ECCCTRL_BUFFER_MASK 0 +#define BM_GPMI_ECCCTRL_BUFFER_MASK (0x1ff << BP_GPMI_ECCCTRL_BUFFER_MASK) +#define BF_GPMI_ECCCTRL_BUFFER_MASK(v) \ + (((v) << BP_GPMI_ECCCTRL_BUFFER_MASK) & BM_GPMI_ECCCTRL_BUFFER_MASK) +#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY 0x100 +#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE 0x1FF + +#define HW_GPMI_ECCCOUNT 0x00000030 +#define HW_GPMI_PAYLOAD 0x00000040 +#define HW_GPMI_AUXILIARY 0x00000050 +#define HW_GPMI_CTRL1 0x00000060 +#define HW_GPMI_CTRL1_SET 0x00000064 +#define HW_GPMI_CTRL1_CLR 0x00000068 +#define HW_GPMI_CTRL1_TOG 0x0000006c + +#define BP_GPMI_CTRL1_DECOUPLE_CS 24 +#define BM_GPMI_CTRL1_DECOUPLE_CS (1 << BP_GPMI_CTRL1_DECOUPLE_CS) + +#define BP_GPMI_CTRL1_WRN_DLY_SEL 22 +#define BM_GPMI_CTRL1_WRN_DLY_SEL (0x3 << BP_GPMI_CTRL1_WRN_DLY_SEL) +#define BF_GPMI_CTRL1_WRN_DLY_SEL(v) \ + (((v) << BP_GPMI_CTRL1_WRN_DLY_SEL) & BM_GPMI_CTRL1_WRN_DLY_SEL) +#define BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS 0x0 +#define BV_GPMI_CTRL1_WRN_DLY_SEL_6_TO_10NS 0x1 +#define BV_GPMI_CTRL1_WRN_DLY_SEL_7_TO_12NS 0x2 +#define BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY 0x3 + +#define BM_GPMI_CTRL1_BCH_MODE (1 << 18) + +#define BP_GPMI_CTRL1_DLL_ENABLE 17 +#define BM_GPMI_CTRL1_DLL_ENABLE (1 << BP_GPMI_CTRL1_DLL_ENABLE) + +#define BP_GPMI_CTRL1_HALF_PERIOD 16 +#define BM_GPMI_CTRL1_HALF_PERIOD (1 << BP_GPMI_CTRL1_HALF_PERIOD) + +#define BP_GPMI_CTRL1_RDN_DELAY 12 +#define BM_GPMI_CTRL1_RDN_DELAY (0xf << BP_GPMI_CTRL1_RDN_DELAY) +#define BF_GPMI_CTRL1_RDN_DELAY(v) \ + (((v) << BP_GPMI_CTRL1_RDN_DELAY) & BM_GPMI_CTRL1_RDN_DELAY) + +#define BM_GPMI_CTRL1_DEV_RESET (1 << 3) +#define BV_GPMI_CTRL1_DEV_RESET__ENABLED 0x0 +#define BV_GPMI_CTRL1_DEV_RESET__DISABLED 0x1 + +#define BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY (1 << 2) +#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVELOW 0x0 +#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVEHIGH 0x1 + +#define BM_GPMI_CTRL1_CAMERA_MODE (1 << 1) +#define BV_GPMI_CTRL1_GPMI_MODE__NAND 0x0 +#define BV_GPMI_CTRL1_GPMI_MODE__ATA 0x1 + +#define BM_GPMI_CTRL1_GPMI_MODE (1 << 0) + +#define HW_GPMI_TIMING0 0x00000070 + +#define BP_GPMI_TIMING0_ADDRESS_SETUP 16 +#define BM_GPMI_TIMING0_ADDRESS_SETUP (0xff << BP_GPMI_TIMING0_ADDRESS_SETUP) +#define BF_GPMI_TIMING0_ADDRESS_SETUP(v) \ + (((v) << BP_GPMI_TIMING0_ADDRESS_SETUP) & BM_GPMI_TIMING0_ADDRESS_SETUP) + +#define BP_GPMI_TIMING0_DATA_HOLD 8 +#define BM_GPMI_TIMING0_DATA_HOLD (0xff << BP_GPMI_TIMING0_DATA_HOLD) +#define BF_GPMI_TIMING0_DATA_HOLD(v) \ + (((v) << BP_GPMI_TIMING0_DATA_HOLD) & BM_GPMI_TIMING0_DATA_HOLD) + +#define BP_GPMI_TIMING0_DATA_SETUP 0 +#define BM_GPMI_TIMING0_DATA_SETUP (0xff << BP_GPMI_TIMING0_DATA_SETUP) +#define BF_GPMI_TIMING0_DATA_SETUP(v) \ + (((v) << BP_GPMI_TIMING0_DATA_SETUP) & BM_GPMI_TIMING0_DATA_SETUP) + +#define HW_GPMI_TIMING1 0x00000080 +#define BP_GPMI_TIMING1_BUSY_TIMEOUT 16 +#define BM_GPMI_TIMING1_BUSY_TIMEOUT (0xffff << BP_GPMI_TIMING1_BUSY_TIMEOUT) +#define BF_GPMI_TIMING1_BUSY_TIMEOUT(v) \ + (((v) << BP_GPMI_TIMING1_BUSY_TIMEOUT) & BM_GPMI_TIMING1_BUSY_TIMEOUT) + +#define HW_GPMI_TIMING2 0x00000090 +#define HW_GPMI_DATA 0x000000a0 + +/* MX28 uses this to detect READY. */ +#define HW_GPMI_STAT 0x000000b0 +#define MX28_BP_GPMI_STAT_READY_BUSY 24 +#define MX28_BM_GPMI_STAT_READY_BUSY (0xff << MX28_BP_GPMI_STAT_READY_BUSY) +#define MX28_BF_GPMI_STAT_READY_BUSY(v) \ + (((v) << MX28_BP_GPMI_STAT_READY_BUSY) & MX28_BM_GPMI_STAT_READY_BUSY) + +/* MX23 uses this to detect READY. */ +#define HW_GPMI_DEBUG 0x000000c0 +#define MX23_BP_GPMI_DEBUG_READY0 28 +#define MX23_BM_GPMI_DEBUG_READY0 (1 << MX23_BP_GPMI_DEBUG_READY0) +#endif diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c new file mode 100644 index 000000000..8dcc7b8fe --- /dev/null +++ b/drivers/mtd/nand/hisi504_nand.c @@ -0,0 +1,890 @@ +/* + * Hisilicon NAND Flash controller driver + * + * Copyright © 2012-2014 HiSilicon Technologies Co., Ltd. + * http://www.hisilicon.com + * + * Author: Zhou Wang <wangzhou.bry@gmail.com> + * The initial developer of the original code is Zhiyong Cai + * <caizhiyong@huawei.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include <linux/of.h> +#include <linux/of_mtd.h> +#include <linux/mtd/mtd.h> +#include <linux/sizes.h> +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/mtd/nand.h> +#include <linux/dma-mapping.h> +#include <linux/platform_device.h> +#include <linux/mtd/partitions.h> + +#define HINFC504_MAX_CHIP (4) +#define HINFC504_W_LATCH (5) +#define HINFC504_R_LATCH (7) +#define HINFC504_RW_LATCH (3) + +#define HINFC504_NFC_TIMEOUT (2 * HZ) +#define HINFC504_NFC_PM_TIMEOUT (1 * HZ) +#define HINFC504_NFC_DMA_TIMEOUT (5 * HZ) +#define HINFC504_CHIP_DELAY (25) + +#define HINFC504_REG_BASE_ADDRESS_LEN (0x100) +#define HINFC504_BUFFER_BASE_ADDRESS_LEN (2048 + 128) + +#define HINFC504_ADDR_CYCLE_MASK 0x4 + +#define HINFC504_CON 0x00 +#define HINFC504_CON_OP_MODE_NORMAL BIT(0) +#define HINFC504_CON_PAGEISZE_SHIFT (1) +#define HINFC504_CON_PAGESIZE_MASK (0x07) +#define HINFC504_CON_BUS_WIDTH BIT(4) +#define HINFC504_CON_READY_BUSY_SEL BIT(8) +#define HINFC504_CON_ECCTYPE_SHIFT (9) +#define HINFC504_CON_ECCTYPE_MASK (0x07) + +#define HINFC504_PWIDTH 0x04 +#define SET_HINFC504_PWIDTH(_w_lcnt, _r_lcnt, _rw_hcnt) \ + ((_w_lcnt) | (((_r_lcnt) & 0x0F) << 4) | (((_rw_hcnt) & 0x0F) << 8)) + +#define HINFC504_CMD 0x0C +#define HINFC504_ADDRL 0x10 +#define HINFC504_ADDRH 0x14 +#define HINFC504_DATA_NUM 0x18 + +#define HINFC504_OP 0x1C +#define HINFC504_OP_READ_DATA_EN BIT(1) +#define HINFC504_OP_WAIT_READY_EN BIT(2) +#define HINFC504_OP_CMD2_EN BIT(3) +#define HINFC504_OP_WRITE_DATA_EN BIT(4) +#define HINFC504_OP_ADDR_EN BIT(5) +#define HINFC504_OP_CMD1_EN BIT(6) +#define HINFC504_OP_NF_CS_SHIFT (7) +#define HINFC504_OP_NF_CS_MASK (3) +#define HINFC504_OP_ADDR_CYCLE_SHIFT (9) +#define HINFC504_OP_ADDR_CYCLE_MASK (7) + +#define HINFC504_STATUS 0x20 +#define HINFC504_READY BIT(0) + +#define HINFC504_INTEN 0x24 +#define HINFC504_INTEN_DMA BIT(9) +#define HINFC504_INTEN_UE BIT(6) +#define HINFC504_INTEN_CE BIT(5) + +#define HINFC504_INTS 0x28 +#define HINFC504_INTS_DMA BIT(9) +#define HINFC504_INTS_UE BIT(6) +#define HINFC504_INTS_CE BIT(5) + +#define HINFC504_INTCLR 0x2C +#define HINFC504_INTCLR_DMA BIT(9) +#define HINFC504_INTCLR_UE BIT(6) +#define HINFC504_INTCLR_CE BIT(5) + +#define HINFC504_ECC_STATUS 0x5C +#define HINFC504_ECC_16_BIT_SHIFT 12 + +#define HINFC504_DMA_CTRL 0x60 +#define HINFC504_DMA_CTRL_DMA_START BIT(0) +#define HINFC504_DMA_CTRL_WE BIT(1) +#define HINFC504_DMA_CTRL_DATA_AREA_EN BIT(2) +#define HINFC504_DMA_CTRL_OOB_AREA_EN BIT(3) +#define HINFC504_DMA_CTRL_BURST4_EN BIT(4) +#define HINFC504_DMA_CTRL_BURST8_EN BIT(5) +#define HINFC504_DMA_CTRL_BURST16_EN BIT(6) +#define HINFC504_DMA_CTRL_ADDR_NUM_SHIFT (7) +#define HINFC504_DMA_CTRL_ADDR_NUM_MASK (1) +#define HINFC504_DMA_CTRL_CS_SHIFT (8) +#define HINFC504_DMA_CTRL_CS_MASK (0x03) + +#define HINFC504_DMA_ADDR_DATA 0x64 +#define HINFC504_DMA_ADDR_OOB 0x68 + +#define HINFC504_DMA_LEN 0x6C +#define HINFC504_DMA_LEN_OOB_SHIFT (16) +#define HINFC504_DMA_LEN_OOB_MASK (0xFFF) + +#define HINFC504_DMA_PARA 0x70 +#define HINFC504_DMA_PARA_DATA_RW_EN BIT(0) +#define HINFC504_DMA_PARA_OOB_RW_EN BIT(1) +#define HINFC504_DMA_PARA_DATA_EDC_EN BIT(2) +#define HINFC504_DMA_PARA_OOB_EDC_EN BIT(3) +#define HINFC504_DMA_PARA_DATA_ECC_EN BIT(4) +#define HINFC504_DMA_PARA_OOB_ECC_EN BIT(5) + +#define HINFC_VERSION 0x74 +#define HINFC504_LOG_READ_ADDR 0x7C +#define HINFC504_LOG_READ_LEN 0x80 + +#define HINFC504_NANDINFO_LEN 0x10 + +struct hinfc_host { + struct nand_chip chip; + struct mtd_info mtd; + struct device *dev; + void __iomem *iobase; + void __iomem *mmio; + struct completion cmd_complete; + unsigned int offset; + unsigned int command; + int chipselect; + unsigned int addr_cycle; + u32 addr_value[2]; + u32 cache_addr_value[2]; + char *buffer; + dma_addr_t dma_buffer; + dma_addr_t dma_oob; + int version; + unsigned int irq_status; /* interrupt status */ +}; + +static inline unsigned int hinfc_read(struct hinfc_host *host, unsigned int reg) +{ + return readl(host->iobase + reg); +} + +static inline void hinfc_write(struct hinfc_host *host, unsigned int value, + unsigned int reg) +{ + writel(value, host->iobase + reg); +} + +static void wait_controller_finished(struct hinfc_host *host) +{ + unsigned long timeout = jiffies + HINFC504_NFC_TIMEOUT; + int val; + + while (time_before(jiffies, timeout)) { + val = hinfc_read(host, HINFC504_STATUS); + if (host->command == NAND_CMD_ERASE2) { + /* nfc is ready */ + while (!(val & HINFC504_READY)) { + usleep_range(500, 1000); + val = hinfc_read(host, HINFC504_STATUS); + } + return; + } + + if (val & HINFC504_READY) + return; + } + + /* wait cmd timeout */ + dev_err(host->dev, "Wait NAND controller exec cmd timeout.\n"); +} + +static void hisi_nfc_dma_transfer(struct hinfc_host *host, int todev) +{ + struct mtd_info *mtd = &host->mtd; + struct nand_chip *chip = mtd->priv; + unsigned long val; + int ret; + + hinfc_write(host, host->dma_buffer, HINFC504_DMA_ADDR_DATA); + hinfc_write(host, host->dma_oob, HINFC504_DMA_ADDR_OOB); + + if (chip->ecc.mode == NAND_ECC_NONE) { + hinfc_write(host, ((mtd->oobsize & HINFC504_DMA_LEN_OOB_MASK) + << HINFC504_DMA_LEN_OOB_SHIFT), HINFC504_DMA_LEN); + + hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN + | HINFC504_DMA_PARA_OOB_RW_EN, HINFC504_DMA_PARA); + } else { + if (host->command == NAND_CMD_READOOB) + hinfc_write(host, HINFC504_DMA_PARA_OOB_RW_EN + | HINFC504_DMA_PARA_OOB_EDC_EN + | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA); + else + hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN + | HINFC504_DMA_PARA_OOB_RW_EN + | HINFC504_DMA_PARA_DATA_EDC_EN + | HINFC504_DMA_PARA_OOB_EDC_EN + | HINFC504_DMA_PARA_DATA_ECC_EN + | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA); + + } + + val = (HINFC504_DMA_CTRL_DMA_START | HINFC504_DMA_CTRL_BURST4_EN + | HINFC504_DMA_CTRL_BURST8_EN | HINFC504_DMA_CTRL_BURST16_EN + | HINFC504_DMA_CTRL_DATA_AREA_EN | HINFC504_DMA_CTRL_OOB_AREA_EN + | ((host->addr_cycle == 4 ? 1 : 0) + << HINFC504_DMA_CTRL_ADDR_NUM_SHIFT) + | ((host->chipselect & HINFC504_DMA_CTRL_CS_MASK) + << HINFC504_DMA_CTRL_CS_SHIFT)); + + if (todev) + val |= HINFC504_DMA_CTRL_WE; + + init_completion(&host->cmd_complete); + + hinfc_write(host, val, HINFC504_DMA_CTRL); + ret = wait_for_completion_timeout(&host->cmd_complete, + HINFC504_NFC_DMA_TIMEOUT); + + if (!ret) { + dev_err(host->dev, "DMA operation(irq) timeout!\n"); + /* sanity check */ + val = hinfc_read(host, HINFC504_DMA_CTRL); + if (!(val & HINFC504_DMA_CTRL_DMA_START)) + dev_err(host->dev, "DMA is already done but without irq ACK!\n"); + else + dev_err(host->dev, "DMA is really timeout!\n"); + } +} + +static int hisi_nfc_send_cmd_pageprog(struct hinfc_host *host) +{ + host->addr_value[0] &= 0xffff0000; + + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL); + hinfc_write(host, host->addr_value[1], HINFC504_ADDRH); + hinfc_write(host, NAND_CMD_PAGEPROG << 8 | NAND_CMD_SEQIN, + HINFC504_CMD); + + hisi_nfc_dma_transfer(host, 1); + + return 0; +} + +static int hisi_nfc_send_cmd_readstart(struct hinfc_host *host) +{ + struct mtd_info *mtd = &host->mtd; + + if ((host->addr_value[0] == host->cache_addr_value[0]) && + (host->addr_value[1] == host->cache_addr_value[1])) + return 0; + + host->addr_value[0] &= 0xffff0000; + + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL); + hinfc_write(host, host->addr_value[1], HINFC504_ADDRH); + hinfc_write(host, NAND_CMD_READSTART << 8 | NAND_CMD_READ0, + HINFC504_CMD); + + hinfc_write(host, 0, HINFC504_LOG_READ_ADDR); + hinfc_write(host, mtd->writesize + mtd->oobsize, + HINFC504_LOG_READ_LEN); + + hisi_nfc_dma_transfer(host, 0); + + host->cache_addr_value[0] = host->addr_value[0]; + host->cache_addr_value[1] = host->addr_value[1]; + + return 0; +} + +static int hisi_nfc_send_cmd_erase(struct hinfc_host *host) +{ + hinfc_write(host, host->addr_value[0], HINFC504_ADDRL); + hinfc_write(host, (NAND_CMD_ERASE2 << 8) | NAND_CMD_ERASE1, + HINFC504_CMD); + + hinfc_write(host, HINFC504_OP_WAIT_READY_EN + | HINFC504_OP_CMD2_EN + | HINFC504_OP_CMD1_EN + | HINFC504_OP_ADDR_EN + | ((host->chipselect & HINFC504_OP_NF_CS_MASK) + << HINFC504_OP_NF_CS_SHIFT) + | ((host->addr_cycle & HINFC504_OP_ADDR_CYCLE_MASK) + << HINFC504_OP_ADDR_CYCLE_SHIFT), + HINFC504_OP); + + wait_controller_finished(host); + + return 0; +} + +static int hisi_nfc_send_cmd_readid(struct hinfc_host *host) +{ + hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM); + hinfc_write(host, NAND_CMD_READID, HINFC504_CMD); + hinfc_write(host, 0, HINFC504_ADDRL); + + hinfc_write(host, HINFC504_OP_CMD1_EN | HINFC504_OP_ADDR_EN + | HINFC504_OP_READ_DATA_EN + | ((host->chipselect & HINFC504_OP_NF_CS_MASK) + << HINFC504_OP_NF_CS_SHIFT) + | 1 << HINFC504_OP_ADDR_CYCLE_SHIFT, HINFC504_OP); + + wait_controller_finished(host); + + return 0; +} + +static int hisi_nfc_send_cmd_status(struct hinfc_host *host) +{ + hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM); + hinfc_write(host, NAND_CMD_STATUS, HINFC504_CMD); + hinfc_write(host, HINFC504_OP_CMD1_EN + | HINFC504_OP_READ_DATA_EN + | ((host->chipselect & HINFC504_OP_NF_CS_MASK) + << HINFC504_OP_NF_CS_SHIFT), + HINFC504_OP); + + wait_controller_finished(host); + + return 0; +} + +static int hisi_nfc_send_cmd_reset(struct hinfc_host *host, int chipselect) +{ + hinfc_write(host, NAND_CMD_RESET, HINFC504_CMD); + + hinfc_write(host, HINFC504_OP_CMD1_EN + | ((chipselect & HINFC504_OP_NF_CS_MASK) + << HINFC504_OP_NF_CS_SHIFT) + | HINFC504_OP_WAIT_READY_EN, + HINFC504_OP); + + wait_controller_finished(host); + + return 0; +} + +static void hisi_nfc_select_chip(struct mtd_info *mtd, int chipselect) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + + if (chipselect < 0) + return; + + host->chipselect = chipselect; +} + +static uint8_t hisi_nfc_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + + if (host->command == NAND_CMD_STATUS) + return *(uint8_t *)(host->mmio); + + host->offset++; + + if (host->command == NAND_CMD_READID) + return *(uint8_t *)(host->mmio + host->offset - 1); + + return *(uint8_t *)(host->buffer + host->offset - 1); +} + +static u16 hisi_nfc_read_word(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + + host->offset += 2; + return *(u16 *)(host->buffer + host->offset - 2); +} + +static void +hisi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + + memcpy(host->buffer + host->offset, buf, len); + host->offset += len; +} + +static void hisi_nfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + + memcpy(buf, host->buffer + host->offset, len); + host->offset += len; +} + +static void set_addr(struct mtd_info *mtd, int column, int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + unsigned int command = host->command; + + host->addr_cycle = 0; + host->addr_value[0] = 0; + host->addr_value[1] = 0; + + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + + host->addr_value[0] = column & 0xffff; + host->addr_cycle = 2; + } + if (page_addr != -1) { + host->addr_value[0] |= (page_addr & 0xffff) + << (host->addr_cycle * 8); + host->addr_cycle += 2; + /* One more address cycle for devices > 128MiB */ + if (chip->chipsize > (128 << 20)) { + host->addr_cycle += 1; + if (host->command == NAND_CMD_ERASE1) + host->addr_value[0] |= ((page_addr >> 16) & 0xff) << 16; + else + host->addr_value[1] |= ((page_addr >> 16) & 0xff); + } + } +} + +static void hisi_nfc_cmdfunc(struct mtd_info *mtd, unsigned command, int column, + int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct hinfc_host *host = chip->priv; + int is_cache_invalid = 1; + unsigned int flag = 0; + + host->command = command; + + switch (command) { + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + if (command == NAND_CMD_READ0) + host->offset = column; + else + host->offset = column + mtd->writesize; + + is_cache_invalid = 0; + set_addr(mtd, column, page_addr); + hisi_nfc_send_cmd_readstart(host); + break; + + case NAND_CMD_SEQIN: + host->offset = column; + set_addr(mtd, column, page_addr); + break; + + case NAND_CMD_ERASE1: + set_addr(mtd, column, page_addr); + break; + + case NAND_CMD_PAGEPROG: + hisi_nfc_send_cmd_pageprog(host); + break; + + case NAND_CMD_ERASE2: + hisi_nfc_send_cmd_erase(host); + break; + + case NAND_CMD_READID: + host->offset = column; + memset(host->mmio, 0, 0x10); + hisi_nfc_send_cmd_readid(host); + break; + + case NAND_CMD_STATUS: + flag = hinfc_read(host, HINFC504_CON); + if (chip->ecc.mode == NAND_ECC_HW) + hinfc_write(host, + flag & ~(HINFC504_CON_ECCTYPE_MASK << + HINFC504_CON_ECCTYPE_SHIFT), HINFC504_CON); + + host->offset = 0; + memset(host->mmio, 0, 0x10); + hisi_nfc_send_cmd_status(host); + hinfc_write(host, flag, HINFC504_CON); + break; + + case NAND_CMD_RESET: + hisi_nfc_send_cmd_reset(host, host->chipselect); + break; + + default: + dev_err(host->dev, "Error: unsupported cmd(cmd=%x, col=%x, page=%x)\n", + command, column, page_addr); + } + + if (is_cache_invalid) { + host->cache_addr_value[0] = ~0; + host->cache_addr_value[1] = ~0; + } +} + +static irqreturn_t hinfc_irq_handle(int irq, void *devid) +{ + struct hinfc_host *host = devid; + unsigned int flag; + + flag = hinfc_read(host, HINFC504_INTS); + /* store interrupts state */ + host->irq_status |= flag; + + if (flag & HINFC504_INTS_DMA) { + hinfc_write(host, HINFC504_INTCLR_DMA, HINFC504_INTCLR); + complete(&host->cmd_complete); + } else if (flag & HINFC504_INTS_CE) { + hinfc_write(host, HINFC504_INTCLR_CE, HINFC504_INTCLR); + } else if (flag & HINFC504_INTS_UE) { + hinfc_write(host, HINFC504_INTCLR_UE, HINFC504_INTCLR); + } + + return IRQ_HANDLED; +} + +static int hisi_nand_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, int page) +{ + struct hinfc_host *host = chip->priv; + int max_bitflips = 0, stat = 0, stat_max = 0, status_ecc; + int stat_1, stat_2; + + chip->read_buf(mtd, buf, mtd->writesize); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + /* errors which can not be corrected by ECC */ + if (host->irq_status & HINFC504_INTS_UE) { + mtd->ecc_stats.failed++; + } else if (host->irq_status & HINFC504_INTS_CE) { + /* TODO: need add other ECC modes! */ + switch (chip->ecc.strength) { + case 16: + status_ecc = hinfc_read(host, HINFC504_ECC_STATUS) >> + HINFC504_ECC_16_BIT_SHIFT & 0x0fff; + stat_2 = status_ecc & 0x3f; + stat_1 = status_ecc >> 6 & 0x3f; + stat = stat_1 + stat_2; + stat_max = max_t(int, stat_1, stat_2); + } + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(int, max_bitflips, stat_max); + } + host->irq_status = 0; + + return max_bitflips; +} + +static int hisi_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + struct hinfc_host *host = chip->priv; + + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (host->irq_status & HINFC504_INTS_UE) { + host->irq_status = 0; + return -EBADMSG; + } + + host->irq_status = 0; + return 0; +} + +static int hisi_nand_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + chip->write_buf(mtd, buf, mtd->writesize); + if (oob_required) + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static void hisi_nfc_host_init(struct hinfc_host *host) +{ + struct nand_chip *chip = &host->chip; + unsigned int flag = 0; + + host->version = hinfc_read(host, HINFC_VERSION); + host->addr_cycle = 0; + host->addr_value[0] = 0; + host->addr_value[1] = 0; + host->cache_addr_value[0] = ~0; + host->cache_addr_value[1] = ~0; + host->chipselect = 0; + + /* default page size: 2K, ecc_none. need modify */ + flag = HINFC504_CON_OP_MODE_NORMAL | HINFC504_CON_READY_BUSY_SEL + | ((0x001 & HINFC504_CON_PAGESIZE_MASK) + << HINFC504_CON_PAGEISZE_SHIFT) + | ((0x0 & HINFC504_CON_ECCTYPE_MASK) + << HINFC504_CON_ECCTYPE_SHIFT) + | ((chip->options & NAND_BUSWIDTH_16) ? + HINFC504_CON_BUS_WIDTH : 0); + hinfc_write(host, flag, HINFC504_CON); + + memset(host->mmio, 0xff, HINFC504_BUFFER_BASE_ADDRESS_LEN); + + hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH, + HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH); + + /* enable DMA irq */ + hinfc_write(host, HINFC504_INTEN_DMA, HINFC504_INTEN); +} + +static struct nand_ecclayout nand_ecc_2K_16bits = { + .oobavail = 6, + .oobfree = { {2, 6} }, +}; + +static int hisi_nfc_ecc_probe(struct hinfc_host *host) +{ + unsigned int flag; + int size, strength, ecc_bits; + struct device *dev = host->dev; + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = &host->mtd; + struct device_node *np = host->dev->of_node; + + size = of_get_nand_ecc_step_size(np); + strength = of_get_nand_ecc_strength(np); + if (size != 1024) { + dev_err(dev, "error ecc size: %d\n", size); + return -EINVAL; + } + + if ((size == 1024) && ((strength != 8) && (strength != 16) && + (strength != 24) && (strength != 40))) { + dev_err(dev, "ecc size and strength do not match\n"); + return -EINVAL; + } + + chip->ecc.size = size; + chip->ecc.strength = strength; + + chip->ecc.read_page = hisi_nand_read_page_hwecc; + chip->ecc.read_oob = hisi_nand_read_oob; + chip->ecc.write_page = hisi_nand_write_page_hwecc; + + switch (chip->ecc.strength) { + case 16: + ecc_bits = 6; + if (mtd->writesize == 2048) + chip->ecc.layout = &nand_ecc_2K_16bits; + + /* TODO: add more page size support */ + break; + + /* TODO: add more ecc strength support */ + default: + dev_err(dev, "not support strength: %d\n", chip->ecc.strength); + return -EINVAL; + } + + flag = hinfc_read(host, HINFC504_CON); + /* add ecc type configure */ + flag |= ((ecc_bits & HINFC504_CON_ECCTYPE_MASK) + << HINFC504_CON_ECCTYPE_SHIFT); + hinfc_write(host, flag, HINFC504_CON); + + /* enable ecc irq */ + flag = hinfc_read(host, HINFC504_INTEN) & 0xfff; + hinfc_write(host, flag | HINFC504_INTEN_UE | HINFC504_INTEN_CE, + HINFC504_INTEN); + + return 0; +} + +static int hisi_nfc_probe(struct platform_device *pdev) +{ + int ret = 0, irq, buswidth, flag, max_chips = HINFC504_MAX_CHIP; + struct device *dev = &pdev->dev; + struct hinfc_host *host; + struct nand_chip *chip; + struct mtd_info *mtd; + struct resource *res; + struct device_node *np = dev->of_node; + struct mtd_part_parser_data ppdata; + + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + host->dev = dev; + + platform_set_drvdata(pdev, host); + chip = &host->chip; + mtd = &host->mtd; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "no IRQ resource defined\n"); + ret = -ENXIO; + goto err_res; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->iobase = devm_ioremap_resource(dev, res); + if (IS_ERR(host->iobase)) { + ret = PTR_ERR(host->iobase); + goto err_res; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + host->mmio = devm_ioremap_resource(dev, res); + if (IS_ERR(host->mmio)) { + ret = PTR_ERR(host->mmio); + dev_err(dev, "devm_ioremap_resource[1] fail\n"); + goto err_res; + } + + mtd->priv = chip; + mtd->owner = THIS_MODULE; + mtd->name = "hisi_nand"; + mtd->dev.parent = &pdev->dev; + + chip->priv = host; + chip->cmdfunc = hisi_nfc_cmdfunc; + chip->select_chip = hisi_nfc_select_chip; + chip->read_byte = hisi_nfc_read_byte; + chip->read_word = hisi_nfc_read_word; + chip->write_buf = hisi_nfc_write_buf; + chip->read_buf = hisi_nfc_read_buf; + chip->chip_delay = HINFC504_CHIP_DELAY; + + chip->ecc.mode = of_get_nand_ecc_mode(np); + + buswidth = of_get_nand_bus_width(np); + if (buswidth == 16) + chip->options |= NAND_BUSWIDTH_16; + + hisi_nfc_host_init(host); + + ret = devm_request_irq(dev, irq, hinfc_irq_handle, 0x0, "nandc", host); + if (ret) { + dev_err(dev, "failed to request IRQ\n"); + goto err_res; + } + + ret = nand_scan_ident(mtd, max_chips, NULL); + if (ret) { + ret = -ENODEV; + goto err_res; + } + + host->buffer = dmam_alloc_coherent(dev, mtd->writesize + mtd->oobsize, + &host->dma_buffer, GFP_KERNEL); + if (!host->buffer) { + ret = -ENOMEM; + goto err_res; + } + + host->dma_oob = host->dma_buffer + mtd->writesize; + memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize); + + flag = hinfc_read(host, HINFC504_CON); + flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT); + switch (mtd->writesize) { + case 2048: + flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); break; + /* + * TODO: add more pagesize support, + * default pagesize has been set in hisi_nfc_host_init + */ + default: + dev_err(dev, "NON-2KB page size nand flash\n"); + ret = -EINVAL; + goto err_res; + } + hinfc_write(host, flag, HINFC504_CON); + + if (chip->ecc.mode == NAND_ECC_HW) + hisi_nfc_ecc_probe(host); + + ret = nand_scan_tail(mtd); + if (ret) { + dev_err(dev, "nand_scan_tail failed: %d\n", ret); + goto err_res; + } + + ppdata.of_node = np; + ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (ret) { + dev_err(dev, "Err MTD partition=%d\n", ret); + goto err_mtd; + } + + return 0; + +err_mtd: + nand_release(mtd); +err_res: + return ret; +} + +static int hisi_nfc_remove(struct platform_device *pdev) +{ + struct hinfc_host *host = platform_get_drvdata(pdev); + struct mtd_info *mtd = &host->mtd; + + nand_release(mtd); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int hisi_nfc_suspend(struct device *dev) +{ + struct hinfc_host *host = dev_get_drvdata(dev); + unsigned long timeout = jiffies + HINFC504_NFC_PM_TIMEOUT; + + while (time_before(jiffies, timeout)) { + if (((hinfc_read(host, HINFC504_STATUS) & 0x1) == 0x0) && + (hinfc_read(host, HINFC504_DMA_CTRL) & + HINFC504_DMA_CTRL_DMA_START)) { + cond_resched(); + return 0; + } + } + + dev_err(host->dev, "nand controller suspend timeout.\n"); + + return -EAGAIN; +} + +static int hisi_nfc_resume(struct device *dev) +{ + int cs; + struct hinfc_host *host = dev_get_drvdata(dev); + struct nand_chip *chip = &host->chip; + + for (cs = 0; cs < chip->numchips; cs++) + hisi_nfc_send_cmd_reset(host, cs); + hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH, + HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH); + + return 0; +} +#endif +static SIMPLE_DEV_PM_OPS(hisi_nfc_pm_ops, hisi_nfc_suspend, hisi_nfc_resume); + +static const struct of_device_id nfc_id_table[] = { + { .compatible = "hisilicon,504-nfc" }, + {} +}; +MODULE_DEVICE_TABLE(of, nfc_id_table); + +static struct platform_driver hisi_nfc_driver = { + .driver = { + .name = "hisi_nand", + .of_match_table = nfc_id_table, + .pm = &hisi_nfc_pm_ops, + }, + .probe = hisi_nfc_probe, + .remove = hisi_nfc_remove, +}; + +module_platform_driver(hisi_nfc_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Zhou Wang"); +MODULE_AUTHOR("Zhiyong Cai"); +MODULE_DESCRIPTION("Hisilicon Nand Flash Controller Driver"); diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c new file mode 100644 index 000000000..ebf2cce04 --- /dev/null +++ b/drivers/mtd/nand/jz4740_nand.c @@ -0,0 +1,579 @@ +/* + * Copyright (C) 2009-2010, Lars-Peter Clausen <lars@metafoo.de> + * JZ4740 SoC NAND controller driver + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> + +#include <linux/gpio.h> + +#include <asm/mach-jz4740/jz4740_nand.h> + +#define JZ_REG_NAND_CTRL 0x50 +#define JZ_REG_NAND_ECC_CTRL 0x100 +#define JZ_REG_NAND_DATA 0x104 +#define JZ_REG_NAND_PAR0 0x108 +#define JZ_REG_NAND_PAR1 0x10C +#define JZ_REG_NAND_PAR2 0x110 +#define JZ_REG_NAND_IRQ_STAT 0x114 +#define JZ_REG_NAND_IRQ_CTRL 0x118 +#define JZ_REG_NAND_ERR(x) (0x11C + ((x) << 2)) + +#define JZ_NAND_ECC_CTRL_PAR_READY BIT(4) +#define JZ_NAND_ECC_CTRL_ENCODING BIT(3) +#define JZ_NAND_ECC_CTRL_RS BIT(2) +#define JZ_NAND_ECC_CTRL_RESET BIT(1) +#define JZ_NAND_ECC_CTRL_ENABLE BIT(0) + +#define JZ_NAND_STATUS_ERR_COUNT (BIT(31) | BIT(30) | BIT(29)) +#define JZ_NAND_STATUS_PAD_FINISH BIT(4) +#define JZ_NAND_STATUS_DEC_FINISH BIT(3) +#define JZ_NAND_STATUS_ENC_FINISH BIT(2) +#define JZ_NAND_STATUS_UNCOR_ERROR BIT(1) +#define JZ_NAND_STATUS_ERROR BIT(0) + +#define JZ_NAND_CTRL_ENABLE_CHIP(x) BIT((x) << 1) +#define JZ_NAND_CTRL_ASSERT_CHIP(x) BIT(((x) << 1) + 1) +#define JZ_NAND_CTRL_ASSERT_CHIP_MASK 0xaa + +#define JZ_NAND_MEM_CMD_OFFSET 0x08000 +#define JZ_NAND_MEM_ADDR_OFFSET 0x10000 + +struct jz_nand { + struct mtd_info mtd; + struct nand_chip chip; + void __iomem *base; + struct resource *mem; + + unsigned char banks[JZ_NAND_NUM_BANKS]; + void __iomem *bank_base[JZ_NAND_NUM_BANKS]; + struct resource *bank_mem[JZ_NAND_NUM_BANKS]; + + int selected_bank; + + struct gpio_desc *busy_gpio; + bool is_reading; +}; + +static inline struct jz_nand *mtd_to_jz_nand(struct mtd_info *mtd) +{ + return container_of(mtd, struct jz_nand, mtd); +} + +static void jz_nand_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + struct nand_chip *chip = mtd->priv; + uint32_t ctrl; + int banknr; + + ctrl = readl(nand->base + JZ_REG_NAND_CTRL); + ctrl &= ~JZ_NAND_CTRL_ASSERT_CHIP_MASK; + + if (chipnr == -1) { + banknr = -1; + } else { + banknr = nand->banks[chipnr] - 1; + chip->IO_ADDR_R = nand->bank_base[banknr]; + chip->IO_ADDR_W = nand->bank_base[banknr]; + } + writel(ctrl, nand->base + JZ_REG_NAND_CTRL); + + nand->selected_bank = banknr; +} + +static void jz_nand_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + struct nand_chip *chip = mtd->priv; + uint32_t reg; + void __iomem *bank_base = nand->bank_base[nand->selected_bank]; + + BUG_ON(nand->selected_bank < 0); + + if (ctrl & NAND_CTRL_CHANGE) { + BUG_ON((ctrl & NAND_ALE) && (ctrl & NAND_CLE)); + if (ctrl & NAND_ALE) + bank_base += JZ_NAND_MEM_ADDR_OFFSET; + else if (ctrl & NAND_CLE) + bank_base += JZ_NAND_MEM_CMD_OFFSET; + chip->IO_ADDR_W = bank_base; + + reg = readl(nand->base + JZ_REG_NAND_CTRL); + if (ctrl & NAND_NCE) + reg |= JZ_NAND_CTRL_ASSERT_CHIP(nand->selected_bank); + else + reg &= ~JZ_NAND_CTRL_ASSERT_CHIP(nand->selected_bank); + writel(reg, nand->base + JZ_REG_NAND_CTRL); + } + if (dat != NAND_CMD_NONE) + writeb(dat, chip->IO_ADDR_W); +} + +static int jz_nand_dev_ready(struct mtd_info *mtd) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + return gpiod_get_value_cansleep(nand->busy_gpio); +} + +static void jz_nand_hwctl(struct mtd_info *mtd, int mode) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + uint32_t reg; + + writel(0, nand->base + JZ_REG_NAND_IRQ_STAT); + reg = readl(nand->base + JZ_REG_NAND_ECC_CTRL); + + reg |= JZ_NAND_ECC_CTRL_RESET; + reg |= JZ_NAND_ECC_CTRL_ENABLE; + reg |= JZ_NAND_ECC_CTRL_RS; + + switch (mode) { + case NAND_ECC_READ: + reg &= ~JZ_NAND_ECC_CTRL_ENCODING; + nand->is_reading = true; + break; + case NAND_ECC_WRITE: + reg |= JZ_NAND_ECC_CTRL_ENCODING; + nand->is_reading = false; + break; + default: + break; + } + + writel(reg, nand->base + JZ_REG_NAND_ECC_CTRL); +} + +static int jz_nand_calculate_ecc_rs(struct mtd_info *mtd, const uint8_t *dat, + uint8_t *ecc_code) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + uint32_t reg, status; + int i; + unsigned int timeout = 1000; + static uint8_t empty_block_ecc[] = {0xcd, 0x9d, 0x90, 0x58, 0xf4, + 0x8b, 0xff, 0xb7, 0x6f}; + + if (nand->is_reading) + return 0; + + do { + status = readl(nand->base + JZ_REG_NAND_IRQ_STAT); + } while (!(status & JZ_NAND_STATUS_ENC_FINISH) && --timeout); + + if (timeout == 0) + return -1; + + reg = readl(nand->base + JZ_REG_NAND_ECC_CTRL); + reg &= ~JZ_NAND_ECC_CTRL_ENABLE; + writel(reg, nand->base + JZ_REG_NAND_ECC_CTRL); + + for (i = 0; i < 9; ++i) + ecc_code[i] = readb(nand->base + JZ_REG_NAND_PAR0 + i); + + /* If the written data is completly 0xff, we also want to write 0xff as + * ecc, otherwise we will get in trouble when doing subpage writes. */ + if (memcmp(ecc_code, empty_block_ecc, 9) == 0) + memset(ecc_code, 0xff, 9); + + return 0; +} + +static void jz_nand_correct_data(uint8_t *dat, int index, int mask) +{ + int offset = index & 0x7; + uint16_t data; + + index += (index >> 3); + + data = dat[index]; + data |= dat[index+1] << 8; + + mask ^= (data >> offset) & 0x1ff; + data &= ~(0x1ff << offset); + data |= (mask << offset); + + dat[index] = data & 0xff; + dat[index+1] = (data >> 8) & 0xff; +} + +static int jz_nand_correct_ecc_rs(struct mtd_info *mtd, uint8_t *dat, + uint8_t *read_ecc, uint8_t *calc_ecc) +{ + struct jz_nand *nand = mtd_to_jz_nand(mtd); + int i, error_count, index; + uint32_t reg, status, error; + uint32_t t; + unsigned int timeout = 1000; + + t = read_ecc[0]; + + if (t == 0xff) { + for (i = 1; i < 9; ++i) + t &= read_ecc[i]; + + t &= dat[0]; + t &= dat[nand->chip.ecc.size / 2]; + t &= dat[nand->chip.ecc.size - 1]; + + if (t == 0xff) { + for (i = 1; i < nand->chip.ecc.size - 1; ++i) + t &= dat[i]; + if (t == 0xff) + return 0; + } + } + + for (i = 0; i < 9; ++i) + writeb(read_ecc[i], nand->base + JZ_REG_NAND_PAR0 + i); + + reg = readl(nand->base + JZ_REG_NAND_ECC_CTRL); + reg |= JZ_NAND_ECC_CTRL_PAR_READY; + writel(reg, nand->base + JZ_REG_NAND_ECC_CTRL); + + do { + status = readl(nand->base + JZ_REG_NAND_IRQ_STAT); + } while (!(status & JZ_NAND_STATUS_DEC_FINISH) && --timeout); + + if (timeout == 0) + return -1; + + reg = readl(nand->base + JZ_REG_NAND_ECC_CTRL); + reg &= ~JZ_NAND_ECC_CTRL_ENABLE; + writel(reg, nand->base + JZ_REG_NAND_ECC_CTRL); + + if (status & JZ_NAND_STATUS_ERROR) { + if (status & JZ_NAND_STATUS_UNCOR_ERROR) + return -1; + + error_count = (status & JZ_NAND_STATUS_ERR_COUNT) >> 29; + + for (i = 0; i < error_count; ++i) { + error = readl(nand->base + JZ_REG_NAND_ERR(i)); + index = ((error >> 16) & 0x1ff) - 1; + if (index >= 0 && index < 512) + jz_nand_correct_data(dat, index, error & 0x1ff); + } + + return error_count; + } + + return 0; +} + +static int jz_nand_ioremap_resource(struct platform_device *pdev, + const char *name, struct resource **res, void *__iomem *base) +{ + int ret; + + *res = platform_get_resource_byname(pdev, IORESOURCE_MEM, name); + if (!*res) { + dev_err(&pdev->dev, "Failed to get platform %s memory\n", name); + ret = -ENXIO; + goto err; + } + + *res = request_mem_region((*res)->start, resource_size(*res), + pdev->name); + if (!*res) { + dev_err(&pdev->dev, "Failed to request %s memory region\n", name); + ret = -EBUSY; + goto err; + } + + *base = ioremap((*res)->start, resource_size(*res)); + if (!*base) { + dev_err(&pdev->dev, "Failed to ioremap %s memory region\n", name); + ret = -EBUSY; + goto err_release_mem; + } + + return 0; + +err_release_mem: + release_mem_region((*res)->start, resource_size(*res)); +err: + *res = NULL; + *base = NULL; + return ret; +} + +static inline void jz_nand_iounmap_resource(struct resource *res, + void __iomem *base) +{ + iounmap(base); + release_mem_region(res->start, resource_size(res)); +} + +static int jz_nand_detect_bank(struct platform_device *pdev, + struct jz_nand *nand, unsigned char bank, + size_t chipnr, uint8_t *nand_maf_id, + uint8_t *nand_dev_id) +{ + int ret; + int gpio; + char gpio_name[9]; + char res_name[6]; + uint32_t ctrl; + struct mtd_info *mtd = &nand->mtd; + struct nand_chip *chip = &nand->chip; + + /* Request GPIO port. */ + gpio = JZ_GPIO_MEM_CS0 + bank - 1; + sprintf(gpio_name, "NAND CS%d", bank); + ret = gpio_request(gpio, gpio_name); + if (ret) { + dev_warn(&pdev->dev, + "Failed to request %s gpio %d: %d\n", + gpio_name, gpio, ret); + goto notfound_gpio; + } + + /* Request I/O resource. */ + sprintf(res_name, "bank%d", bank); + ret = jz_nand_ioremap_resource(pdev, res_name, + &nand->bank_mem[bank - 1], + &nand->bank_base[bank - 1]); + if (ret) + goto notfound_resource; + + /* Enable chip in bank. */ + jz_gpio_set_function(gpio, JZ_GPIO_FUNC_MEM_CS0); + ctrl = readl(nand->base + JZ_REG_NAND_CTRL); + ctrl |= JZ_NAND_CTRL_ENABLE_CHIP(bank - 1); + writel(ctrl, nand->base + JZ_REG_NAND_CTRL); + + if (chipnr == 0) { + /* Detect first chip. */ + ret = nand_scan_ident(mtd, 1, NULL); + if (ret) + goto notfound_id; + + /* Retrieve the IDs from the first chip. */ + chip->select_chip(mtd, 0); + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + *nand_maf_id = chip->read_byte(mtd); + *nand_dev_id = chip->read_byte(mtd); + } else { + /* Detect additional chip. */ + chip->select_chip(mtd, chipnr); + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + if (*nand_maf_id != chip->read_byte(mtd) + || *nand_dev_id != chip->read_byte(mtd)) { + ret = -ENODEV; + goto notfound_id; + } + + /* Update size of the MTD. */ + chip->numchips++; + mtd->size += chip->chipsize; + } + + dev_info(&pdev->dev, "Found chip %i on bank %i\n", chipnr, bank); + return 0; + +notfound_id: + dev_info(&pdev->dev, "No chip found on bank %i\n", bank); + ctrl &= ~(JZ_NAND_CTRL_ENABLE_CHIP(bank - 1)); + writel(ctrl, nand->base + JZ_REG_NAND_CTRL); + jz_gpio_set_function(gpio, JZ_GPIO_FUNC_NONE); + jz_nand_iounmap_resource(nand->bank_mem[bank - 1], + nand->bank_base[bank - 1]); +notfound_resource: + gpio_free(gpio); +notfound_gpio: + return ret; +} + +static int jz_nand_probe(struct platform_device *pdev) +{ + int ret; + struct jz_nand *nand; + struct nand_chip *chip; + struct mtd_info *mtd; + struct jz_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + size_t chipnr, bank_idx; + uint8_t nand_maf_id = 0, nand_dev_id = 0; + + nand = kzalloc(sizeof(*nand), GFP_KERNEL); + if (!nand) + return -ENOMEM; + + ret = jz_nand_ioremap_resource(pdev, "mmio", &nand->mem, &nand->base); + if (ret) + goto err_free; + + nand->busy_gpio = devm_gpiod_get_optional(&pdev->dev, "busy", GPIOD_IN); + if (IS_ERR(nand->busy_gpio)) { + ret = PTR_ERR(nand->busy_gpio); + dev_err(&pdev->dev, "Failed to request busy gpio %d\n", + ret); + goto err_iounmap_mmio; + } + + mtd = &nand->mtd; + chip = &nand->chip; + mtd->priv = chip; + mtd->owner = THIS_MODULE; + mtd->name = "jz4740-nand"; + + chip->ecc.hwctl = jz_nand_hwctl; + chip->ecc.calculate = jz_nand_calculate_ecc_rs; + chip->ecc.correct = jz_nand_correct_ecc_rs; + chip->ecc.mode = NAND_ECC_HW_OOB_FIRST; + chip->ecc.size = 512; + chip->ecc.bytes = 9; + chip->ecc.strength = 4; + + if (pdata) + chip->ecc.layout = pdata->ecc_layout; + + chip->chip_delay = 50; + chip->cmd_ctrl = jz_nand_cmd_ctrl; + chip->select_chip = jz_nand_select_chip; + + if (nand->busy_gpio) + chip->dev_ready = jz_nand_dev_ready; + + platform_set_drvdata(pdev, nand); + + /* We are going to autodetect NAND chips in the banks specified in the + * platform data. Although nand_scan_ident() can detect multiple chips, + * it requires those chips to be numbered consecuitively, which is not + * always the case for external memory banks. And a fixed chip-to-bank + * mapping is not practical either, since for example Dingoo units + * produced at different times have NAND chips in different banks. + */ + chipnr = 0; + for (bank_idx = 0; bank_idx < JZ_NAND_NUM_BANKS; bank_idx++) { + unsigned char bank; + + /* If there is no platform data, look for NAND in bank 1, + * which is the most likely bank since it is the only one + * that can be booted from. + */ + bank = pdata ? pdata->banks[bank_idx] : bank_idx ^ 1; + if (bank == 0) + break; + if (bank > JZ_NAND_NUM_BANKS) { + dev_warn(&pdev->dev, + "Skipping non-existing bank: %d\n", bank); + continue; + } + /* The detection routine will directly or indirectly call + * jz_nand_select_chip(), so nand->banks has to contain the + * bank we're checking. + */ + nand->banks[chipnr] = bank; + if (jz_nand_detect_bank(pdev, nand, bank, chipnr, + &nand_maf_id, &nand_dev_id) == 0) + chipnr++; + else + nand->banks[chipnr] = 0; + } + if (chipnr == 0) { + dev_err(&pdev->dev, "No NAND chips found\n"); + goto err_iounmap_mmio; + } + + if (pdata && pdata->ident_callback) { + pdata->ident_callback(pdev, chip, &pdata->partitions, + &pdata->num_partitions); + } + + ret = nand_scan_tail(mtd); + if (ret) { + dev_err(&pdev->dev, "Failed to scan NAND\n"); + goto err_unclaim_banks; + } + + ret = mtd_device_parse_register(mtd, NULL, NULL, + pdata ? pdata->partitions : NULL, + pdata ? pdata->num_partitions : 0); + + if (ret) { + dev_err(&pdev->dev, "Failed to add mtd device\n"); + goto err_nand_release; + } + + dev_info(&pdev->dev, "Successfully registered JZ4740 NAND driver\n"); + + return 0; + +err_nand_release: + nand_release(mtd); +err_unclaim_banks: + while (chipnr--) { + unsigned char bank = nand->banks[chipnr]; + gpio_free(JZ_GPIO_MEM_CS0 + bank - 1); + jz_nand_iounmap_resource(nand->bank_mem[bank - 1], + nand->bank_base[bank - 1]); + } + writel(0, nand->base + JZ_REG_NAND_CTRL); +err_iounmap_mmio: + jz_nand_iounmap_resource(nand->mem, nand->base); +err_free: + kfree(nand); + return ret; +} + +static int jz_nand_remove(struct platform_device *pdev) +{ + struct jz_nand *nand = platform_get_drvdata(pdev); + size_t i; + + nand_release(&nand->mtd); + + /* Deassert and disable all chips */ + writel(0, nand->base + JZ_REG_NAND_CTRL); + + for (i = 0; i < JZ_NAND_NUM_BANKS; ++i) { + unsigned char bank = nand->banks[i]; + if (bank != 0) { + jz_nand_iounmap_resource(nand->bank_mem[bank - 1], + nand->bank_base[bank - 1]); + gpio_free(JZ_GPIO_MEM_CS0 + bank - 1); + } + } + + jz_nand_iounmap_resource(nand->mem, nand->base); + + kfree(nand); + + return 0; +} + +static struct platform_driver jz_nand_driver = { + .probe = jz_nand_probe, + .remove = jz_nand_remove, + .driver = { + .name = "jz4740-nand", + }, +}; + +module_platform_driver(jz_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>"); +MODULE_DESCRIPTION("NAND controller driver for JZ4740 SoC"); +MODULE_ALIAS("platform:jz4740-nand"); diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c new file mode 100644 index 000000000..79c3b7801 --- /dev/null +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -0,0 +1,889 @@ +/* + * Driver for NAND MLC Controller in LPC32xx + * + * Author: Roland Stigge <stigge@antcom.de> + * + * Copyright © 2011 WORK Microwave GmbH + * Copyright © 2011, 2012 Roland Stigge + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * + * NAND Flash Controller Operation: + * - Read: Auto Decode + * - Write: Auto Encode + * - Tested Page Sizes: 2048, 4096 + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/delay.h> +#include <linux/completion.h> +#include <linux/interrupt.h> +#include <linux/of.h> +#include <linux/of_mtd.h> +#include <linux/of_gpio.h> +#include <linux/mtd/lpc32xx_mlc.h> +#include <linux/io.h> +#include <linux/mm.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> +#include <linux/mtd/nand_ecc.h> + +#define DRV_NAME "lpc32xx_mlc" + +/********************************************************************** +* MLC NAND controller register offsets +**********************************************************************/ + +#define MLC_BUFF(x) (x + 0x00000) +#define MLC_DATA(x) (x + 0x08000) +#define MLC_CMD(x) (x + 0x10000) +#define MLC_ADDR(x) (x + 0x10004) +#define MLC_ECC_ENC_REG(x) (x + 0x10008) +#define MLC_ECC_DEC_REG(x) (x + 0x1000C) +#define MLC_ECC_AUTO_ENC_REG(x) (x + 0x10010) +#define MLC_ECC_AUTO_DEC_REG(x) (x + 0x10014) +#define MLC_RPR(x) (x + 0x10018) +#define MLC_WPR(x) (x + 0x1001C) +#define MLC_RUBP(x) (x + 0x10020) +#define MLC_ROBP(x) (x + 0x10024) +#define MLC_SW_WP_ADD_LOW(x) (x + 0x10028) +#define MLC_SW_WP_ADD_HIG(x) (x + 0x1002C) +#define MLC_ICR(x) (x + 0x10030) +#define MLC_TIME_REG(x) (x + 0x10034) +#define MLC_IRQ_MR(x) (x + 0x10038) +#define MLC_IRQ_SR(x) (x + 0x1003C) +#define MLC_LOCK_PR(x) (x + 0x10044) +#define MLC_ISR(x) (x + 0x10048) +#define MLC_CEH(x) (x + 0x1004C) + +/********************************************************************** +* MLC_CMD bit definitions +**********************************************************************/ +#define MLCCMD_RESET 0xFF + +/********************************************************************** +* MLC_ICR bit definitions +**********************************************************************/ +#define MLCICR_WPROT (1 << 3) +#define MLCICR_LARGEBLOCK (1 << 2) +#define MLCICR_LONGADDR (1 << 1) +#define MLCICR_16BIT (1 << 0) /* unsupported by LPC32x0! */ + +/********************************************************************** +* MLC_TIME_REG bit definitions +**********************************************************************/ +#define MLCTIMEREG_TCEA_DELAY(n) (((n) & 0x03) << 24) +#define MLCTIMEREG_BUSY_DELAY(n) (((n) & 0x1F) << 19) +#define MLCTIMEREG_NAND_TA(n) (((n) & 0x07) << 16) +#define MLCTIMEREG_RD_HIGH(n) (((n) & 0x0F) << 12) +#define MLCTIMEREG_RD_LOW(n) (((n) & 0x0F) << 8) +#define MLCTIMEREG_WR_HIGH(n) (((n) & 0x0F) << 4) +#define MLCTIMEREG_WR_LOW(n) (((n) & 0x0F) << 0) + +/********************************************************************** +* MLC_IRQ_MR and MLC_IRQ_SR bit definitions +**********************************************************************/ +#define MLCIRQ_NAND_READY (1 << 5) +#define MLCIRQ_CONTROLLER_READY (1 << 4) +#define MLCIRQ_DECODE_FAILURE (1 << 3) +#define MLCIRQ_DECODE_ERROR (1 << 2) +#define MLCIRQ_ECC_READY (1 << 1) +#define MLCIRQ_WRPROT_FAULT (1 << 0) + +/********************************************************************** +* MLC_LOCK_PR bit definitions +**********************************************************************/ +#define MLCLOCKPR_MAGIC 0xA25E + +/********************************************************************** +* MLC_ISR bit definitions +**********************************************************************/ +#define MLCISR_DECODER_FAILURE (1 << 6) +#define MLCISR_ERRORS ((1 << 4) | (1 << 5)) +#define MLCISR_ERRORS_DETECTED (1 << 3) +#define MLCISR_ECC_READY (1 << 2) +#define MLCISR_CONTROLLER_READY (1 << 1) +#define MLCISR_NAND_READY (1 << 0) + +/********************************************************************** +* MLC_CEH bit definitions +**********************************************************************/ +#define MLCCEH_NORMAL (1 << 0) + +struct lpc32xx_nand_cfg_mlc { + uint32_t tcea_delay; + uint32_t busy_delay; + uint32_t nand_ta; + uint32_t rd_high; + uint32_t rd_low; + uint32_t wr_high; + uint32_t wr_low; + int wp_gpio; + struct mtd_partition *parts; + unsigned num_parts; +}; + +static struct nand_ecclayout lpc32xx_nand_oob = { + .eccbytes = 40, + .eccpos = { 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, + 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, + 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }, + .oobfree = { + { .offset = 0, + .length = 6, }, + { .offset = 16, + .length = 6, }, + { .offset = 32, + .length = 6, }, + { .offset = 48, + .length = 6, }, + }, +}; + +static struct nand_bbt_descr lpc32xx_nand_bbt = { + .options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB | + NAND_BBT_WRITE, + .pages = { 524224, 0, 0, 0, 0, 0, 0, 0 }, +}; + +static struct nand_bbt_descr lpc32xx_nand_bbt_mirror = { + .options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB | + NAND_BBT_WRITE, + .pages = { 524160, 0, 0, 0, 0, 0, 0, 0 }, +}; + +struct lpc32xx_nand_host { + struct nand_chip nand_chip; + struct lpc32xx_mlc_platform_data *pdata; + struct clk *clk; + struct mtd_info mtd; + void __iomem *io_base; + int irq; + struct lpc32xx_nand_cfg_mlc *ncfg; + struct completion comp_nand; + struct completion comp_controller; + uint32_t llptr; + /* + * Physical addresses of ECC buffer, DMA data buffers, OOB data buffer + */ + dma_addr_t oob_buf_phy; + /* + * Virtual addresses of ECC buffer, DMA data buffers, OOB data buffer + */ + uint8_t *oob_buf; + /* Physical address of DMA base address */ + dma_addr_t io_base_phy; + + struct completion comp_dma; + struct dma_chan *dma_chan; + struct dma_slave_config dma_slave_config; + struct scatterlist sgl; + uint8_t *dma_buf; + uint8_t *dummy_buf; + int mlcsubpages; /* number of 512bytes-subpages */ +}; + +/* + * Activate/Deactivate DMA Operation: + * + * Using the PL080 DMA Controller for transferring the 512 byte subpages + * instead of doing readl() / writel() in a loop slows it down significantly. + * Measurements via getnstimeofday() upon 512 byte subpage reads reveal: + * + * - readl() of 128 x 32 bits in a loop: ~20us + * - DMA read of 512 bytes (32 bit, 4...128 words bursts): ~60us + * - DMA read of 512 bytes (32 bit, no bursts): ~100us + * + * This applies to the transfer itself. In the DMA case: only the + * wait_for_completion() (DMA setup _not_ included). + * + * Note that the 512 bytes subpage transfer is done directly from/to a + * FIFO/buffer inside the NAND controller. Most of the time (~400-800us for a + * 2048 bytes page) is spent waiting for the NAND IRQ, anyway. (The NAND + * controller transferring data between its internal buffer to/from the NAND + * chip.) + * + * Therefore, using the PL080 DMA is disabled by default, for now. + * + */ +static int use_dma; + +static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host) +{ + uint32_t clkrate, tmp; + + /* Reset MLC controller */ + writel(MLCCMD_RESET, MLC_CMD(host->io_base)); + udelay(1000); + + /* Get base clock for MLC block */ + clkrate = clk_get_rate(host->clk); + if (clkrate == 0) + clkrate = 104000000; + + /* Unlock MLC_ICR + * (among others, will be locked again automatically) */ + writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base)); + + /* Configure MLC Controller: Large Block, 5 Byte Address */ + tmp = MLCICR_LARGEBLOCK | MLCICR_LONGADDR; + writel(tmp, MLC_ICR(host->io_base)); + + /* Unlock MLC_TIME_REG + * (among others, will be locked again automatically) */ + writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base)); + + /* Compute clock setup values, see LPC and NAND manual */ + tmp = 0; + tmp |= MLCTIMEREG_TCEA_DELAY(clkrate / host->ncfg->tcea_delay + 1); + tmp |= MLCTIMEREG_BUSY_DELAY(clkrate / host->ncfg->busy_delay + 1); + tmp |= MLCTIMEREG_NAND_TA(clkrate / host->ncfg->nand_ta + 1); + tmp |= MLCTIMEREG_RD_HIGH(clkrate / host->ncfg->rd_high + 1); + tmp |= MLCTIMEREG_RD_LOW(clkrate / host->ncfg->rd_low); + tmp |= MLCTIMEREG_WR_HIGH(clkrate / host->ncfg->wr_high + 1); + tmp |= MLCTIMEREG_WR_LOW(clkrate / host->ncfg->wr_low); + writel(tmp, MLC_TIME_REG(host->io_base)); + + /* Enable IRQ for CONTROLLER_READY and NAND_READY */ + writeb(MLCIRQ_CONTROLLER_READY | MLCIRQ_NAND_READY, + MLC_IRQ_MR(host->io_base)); + + /* Normal nCE operation: nCE controlled by controller */ + writel(MLCCEH_NORMAL, MLC_CEH(host->io_base)); +} + +/* + * Hardware specific access to control lines + */ +static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *nand_chip = mtd->priv; + struct lpc32xx_nand_host *host = nand_chip->priv; + + if (cmd != NAND_CMD_NONE) { + if (ctrl & NAND_CLE) + writel(cmd, MLC_CMD(host->io_base)); + else + writel(cmd, MLC_ADDR(host->io_base)); + } +} + +/* + * Read Device Ready (NAND device _and_ controller ready) + */ +static int lpc32xx_nand_device_ready(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct lpc32xx_nand_host *host = nand_chip->priv; + + if ((readb(MLC_ISR(host->io_base)) & + (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY)) == + (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY)) + return 1; + + return 0; +} + +static irqreturn_t lpc3xxx_nand_irq(int irq, struct lpc32xx_nand_host *host) +{ + uint8_t sr; + + /* Clear interrupt flag by reading status */ + sr = readb(MLC_IRQ_SR(host->io_base)); + if (sr & MLCIRQ_NAND_READY) + complete(&host->comp_nand); + if (sr & MLCIRQ_CONTROLLER_READY) + complete(&host->comp_controller); + + return IRQ_HANDLED; +} + +static int lpc32xx_waitfunc_nand(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct lpc32xx_nand_host *host = chip->priv; + + if (readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY) + goto exit; + + wait_for_completion(&host->comp_nand); + + while (!(readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY)) { + /* Seems to be delayed sometimes by controller */ + dev_dbg(&mtd->dev, "Warning: NAND not ready.\n"); + cpu_relax(); + } + +exit: + return NAND_STATUS_READY; +} + +static int lpc32xx_waitfunc_controller(struct mtd_info *mtd, + struct nand_chip *chip) +{ + struct lpc32xx_nand_host *host = chip->priv; + + if (readb(MLC_ISR(host->io_base)) & MLCISR_CONTROLLER_READY) + goto exit; + + wait_for_completion(&host->comp_controller); + + while (!(readb(MLC_ISR(host->io_base)) & + MLCISR_CONTROLLER_READY)) { + dev_dbg(&mtd->dev, "Warning: Controller not ready.\n"); + cpu_relax(); + } + +exit: + return NAND_STATUS_READY; +} + +static int lpc32xx_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) +{ + lpc32xx_waitfunc_nand(mtd, chip); + lpc32xx_waitfunc_controller(mtd, chip); + + return NAND_STATUS_READY; +} + +/* + * Enable NAND write protect + */ +static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host) +{ + if (gpio_is_valid(host->ncfg->wp_gpio)) + gpio_set_value(host->ncfg->wp_gpio, 0); +} + +/* + * Disable NAND write protect + */ +static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host) +{ + if (gpio_is_valid(host->ncfg->wp_gpio)) + gpio_set_value(host->ncfg->wp_gpio, 1); +} + +static void lpc32xx_dma_complete_func(void *completion) +{ + complete(completion); +} + +static int lpc32xx_xmit_dma(struct mtd_info *mtd, void *mem, int len, + enum dma_transfer_direction dir) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + struct dma_async_tx_descriptor *desc; + int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; + int res; + + sg_init_one(&host->sgl, mem, len); + + res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + if (res != 1) { + dev_err(mtd->dev.parent, "Failed to map sg list\n"); + return -ENXIO; + } + desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir, + flags); + if (!desc) { + dev_err(mtd->dev.parent, "Failed to prepare slave sg\n"); + goto out1; + } + + init_completion(&host->comp_dma); + desc->callback = lpc32xx_dma_complete_func; + desc->callback_param = &host->comp_dma; + + dmaengine_submit(desc); + dma_async_issue_pending(host->dma_chan); + + wait_for_completion_timeout(&host->comp_dma, msecs_to_jiffies(1000)); + + dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + return 0; +out1: + dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + return -ENXIO; +} + +static int lpc32xx_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + struct lpc32xx_nand_host *host = chip->priv; + int i, j; + uint8_t *oobbuf = chip->oob_poi; + uint32_t mlc_isr; + int res; + uint8_t *dma_buf; + bool dma_mapped; + + if ((void *)buf <= high_memory) { + dma_buf = buf; + dma_mapped = true; + } else { + dma_buf = host->dma_buf; + dma_mapped = false; + } + + /* Writing Command and Address */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + /* For all sub-pages */ + for (i = 0; i < host->mlcsubpages; i++) { + /* Start Auto Decode Command */ + writeb(0x00, MLC_ECC_AUTO_DEC_REG(host->io_base)); + + /* Wait for Controller Ready */ + lpc32xx_waitfunc_controller(mtd, chip); + + /* Check ECC Error status */ + mlc_isr = readl(MLC_ISR(host->io_base)); + if (mlc_isr & MLCISR_DECODER_FAILURE) { + mtd->ecc_stats.failed++; + dev_warn(&mtd->dev, "%s: DECODER_FAILURE\n", __func__); + } else if (mlc_isr & MLCISR_ERRORS_DETECTED) { + mtd->ecc_stats.corrected += ((mlc_isr >> 4) & 0x3) + 1; + } + + /* Read 512 + 16 Bytes */ + if (use_dma) { + res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512, + DMA_DEV_TO_MEM); + if (res) + return res; + } else { + for (j = 0; j < (512 >> 2); j++) { + *((uint32_t *)(buf)) = + readl(MLC_BUFF(host->io_base)); + buf += 4; + } + } + for (j = 0; j < (16 >> 2); j++) { + *((uint32_t *)(oobbuf)) = + readl(MLC_BUFF(host->io_base)); + oobbuf += 4; + } + } + + if (use_dma && !dma_mapped) + memcpy(buf, dma_buf, mtd->writesize); + + return 0; +} + +static int lpc32xx_write_page_lowlevel(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + struct lpc32xx_nand_host *host = chip->priv; + const uint8_t *oobbuf = chip->oob_poi; + uint8_t *dma_buf = (uint8_t *)buf; + int res; + int i, j; + + if (use_dma && (void *)buf >= high_memory) { + dma_buf = host->dma_buf; + memcpy(dma_buf, buf, mtd->writesize); + } + + for (i = 0; i < host->mlcsubpages; i++) { + /* Start Encode */ + writeb(0x00, MLC_ECC_ENC_REG(host->io_base)); + + /* Write 512 + 6 Bytes to Buffer */ + if (use_dma) { + res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512, + DMA_MEM_TO_DEV); + if (res) + return res; + } else { + for (j = 0; j < (512 >> 2); j++) { + writel(*((uint32_t *)(buf)), + MLC_BUFF(host->io_base)); + buf += 4; + } + } + writel(*((uint32_t *)(oobbuf)), MLC_BUFF(host->io_base)); + oobbuf += 4; + writew(*((uint16_t *)(oobbuf)), MLC_BUFF(host->io_base)); + oobbuf += 12; + + /* Auto Encode w/ Bit 8 = 0 (see LPC MLC Controller manual) */ + writeb(0x00, MLC_ECC_AUTO_ENC_REG(host->io_base)); + + /* Wait for Controller Ready */ + lpc32xx_waitfunc_controller(mtd, chip); + } + return 0; +} + +static int lpc32xx_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + struct lpc32xx_nand_host *host = chip->priv; + + /* Read whole page - necessary with MLC controller! */ + lpc32xx_read_page(mtd, chip, host->dummy_buf, 1, page); + + return 0; +} + +static int lpc32xx_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + /* None, write_oob conflicts with the automatic LPC MLC ECC decoder! */ + return 0; +} + +/* Prepares MLC for transfers with H/W ECC enabled: always enabled anyway */ +static void lpc32xx_ecc_enable(struct mtd_info *mtd, int mode) +{ + /* Always enabled! */ +} + +static int lpc32xx_dma_setup(struct lpc32xx_nand_host *host) +{ + struct mtd_info *mtd = &host->mtd; + dma_cap_mask_t mask; + + if (!host->pdata || !host->pdata->dma_filter) { + dev_err(mtd->dev.parent, "no DMA platform data\n"); + return -ENOENT; + } + + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + host->dma_chan = dma_request_channel(mask, host->pdata->dma_filter, + "nand-mlc"); + if (!host->dma_chan) { + dev_err(mtd->dev.parent, "Failed to request DMA channel\n"); + return -EBUSY; + } + + /* + * Set direction to a sensible value even if the dmaengine driver + * should ignore it. With the default (DMA_MEM_TO_MEM), the amba-pl08x + * driver criticizes it as "alien transfer direction". + */ + host->dma_slave_config.direction = DMA_DEV_TO_MEM; + host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + host->dma_slave_config.src_maxburst = 128; + host->dma_slave_config.dst_maxburst = 128; + /* DMA controller does flow control: */ + host->dma_slave_config.device_fc = false; + host->dma_slave_config.src_addr = MLC_BUFF(host->io_base_phy); + host->dma_slave_config.dst_addr = MLC_BUFF(host->io_base_phy); + if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) { + dev_err(mtd->dev.parent, "Failed to setup DMA slave\n"); + goto out1; + } + + return 0; +out1: + dma_release_channel(host->dma_chan); + return -ENXIO; +} + +static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev) +{ + struct lpc32xx_nand_cfg_mlc *ncfg; + struct device_node *np = dev->of_node; + + ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); + if (!ncfg) + return NULL; + + of_property_read_u32(np, "nxp,tcea-delay", &ncfg->tcea_delay); + of_property_read_u32(np, "nxp,busy-delay", &ncfg->busy_delay); + of_property_read_u32(np, "nxp,nand-ta", &ncfg->nand_ta); + of_property_read_u32(np, "nxp,rd-high", &ncfg->rd_high); + of_property_read_u32(np, "nxp,rd-low", &ncfg->rd_low); + of_property_read_u32(np, "nxp,wr-high", &ncfg->wr_high); + of_property_read_u32(np, "nxp,wr-low", &ncfg->wr_low); + + if (!ncfg->tcea_delay || !ncfg->busy_delay || !ncfg->nand_ta || + !ncfg->rd_high || !ncfg->rd_low || !ncfg->wr_high || + !ncfg->wr_low) { + dev_err(dev, "chip parameters not specified correctly\n"); + return NULL; + } + + ncfg->wp_gpio = of_get_named_gpio(np, "gpios", 0); + + return ncfg; +} + +/* + * Probe for NAND controller + */ +static int lpc32xx_nand_probe(struct platform_device *pdev) +{ + struct lpc32xx_nand_host *host; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + struct resource *rc; + int res; + struct mtd_part_parser_data ppdata = {}; + + /* Allocate memory for the device structure (and zero it) */ + host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + + rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->io_base = devm_ioremap_resource(&pdev->dev, rc); + if (IS_ERR(host->io_base)) + return PTR_ERR(host->io_base); + + host->io_base_phy = rc->start; + + mtd = &host->mtd; + nand_chip = &host->nand_chip; + if (pdev->dev.of_node) + host->ncfg = lpc32xx_parse_dt(&pdev->dev); + if (!host->ncfg) { + dev_err(&pdev->dev, + "Missing or bad NAND config from device tree\n"); + return -ENOENT; + } + if (host->ncfg->wp_gpio == -EPROBE_DEFER) + return -EPROBE_DEFER; + if (gpio_is_valid(host->ncfg->wp_gpio) && + gpio_request(host->ncfg->wp_gpio, "NAND WP")) { + dev_err(&pdev->dev, "GPIO not available\n"); + return -EBUSY; + } + lpc32xx_wp_disable(host); + + host->pdata = dev_get_platdata(&pdev->dev); + + nand_chip->priv = host; /* link the private data structures */ + mtd->priv = nand_chip; + mtd->owner = THIS_MODULE; + mtd->dev.parent = &pdev->dev; + + /* Get NAND clock */ + host->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(host->clk)) { + dev_err(&pdev->dev, "Clock initialization failure\n"); + res = -ENOENT; + goto err_exit1; + } + clk_enable(host->clk); + + nand_chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl; + nand_chip->dev_ready = lpc32xx_nand_device_ready; + nand_chip->chip_delay = 25; /* us */ + nand_chip->IO_ADDR_R = MLC_DATA(host->io_base); + nand_chip->IO_ADDR_W = MLC_DATA(host->io_base); + + /* Init NAND controller */ + lpc32xx_nand_setup(host); + + platform_set_drvdata(pdev, host); + + /* Initialize function pointers */ + nand_chip->ecc.hwctl = lpc32xx_ecc_enable; + nand_chip->ecc.read_page_raw = lpc32xx_read_page; + nand_chip->ecc.read_page = lpc32xx_read_page; + nand_chip->ecc.write_page_raw = lpc32xx_write_page_lowlevel; + nand_chip->ecc.write_page = lpc32xx_write_page_lowlevel; + nand_chip->ecc.write_oob = lpc32xx_write_oob; + nand_chip->ecc.read_oob = lpc32xx_read_oob; + nand_chip->ecc.strength = 4; + nand_chip->waitfunc = lpc32xx_waitfunc; + + nand_chip->options = NAND_NO_SUBPAGE_WRITE; + nand_chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; + nand_chip->bbt_td = &lpc32xx_nand_bbt; + nand_chip->bbt_md = &lpc32xx_nand_bbt_mirror; + + if (use_dma) { + res = lpc32xx_dma_setup(host); + if (res) { + res = -EIO; + goto err_exit2; + } + } + + /* + * Scan to find existance of the device and + * Get the type of NAND device SMALL block or LARGE block + */ + if (nand_scan_ident(mtd, 1, NULL)) { + res = -ENXIO; + goto err_exit3; + } + + host->dma_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); + if (!host->dma_buf) { + res = -ENOMEM; + goto err_exit3; + } + + host->dummy_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); + if (!host->dummy_buf) { + res = -ENOMEM; + goto err_exit3; + } + + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = mtd->writesize; + nand_chip->ecc.layout = &lpc32xx_nand_oob; + host->mlcsubpages = mtd->writesize / 512; + + /* initially clear interrupt status */ + readb(MLC_IRQ_SR(host->io_base)); + + init_completion(&host->comp_nand); + init_completion(&host->comp_controller); + + host->irq = platform_get_irq(pdev, 0); + if ((host->irq < 0) || (host->irq >= NR_IRQS)) { + dev_err(&pdev->dev, "failed to get platform irq\n"); + res = -EINVAL; + goto err_exit3; + } + + if (request_irq(host->irq, (irq_handler_t)&lpc3xxx_nand_irq, + IRQF_TRIGGER_HIGH, DRV_NAME, host)) { + dev_err(&pdev->dev, "Error requesting NAND IRQ\n"); + res = -ENXIO; + goto err_exit3; + } + + /* + * Fills out all the uninitialized function pointers with the defaults + * And scans for a bad block table if appropriate. + */ + if (nand_scan_tail(mtd)) { + res = -ENXIO; + goto err_exit4; + } + + mtd->name = DRV_NAME; + + ppdata.of_node = pdev->dev.of_node; + res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts, + host->ncfg->num_parts); + if (!res) + return res; + + nand_release(mtd); + +err_exit4: + free_irq(host->irq, host); +err_exit3: + if (use_dma) + dma_release_channel(host->dma_chan); +err_exit2: + clk_disable(host->clk); + clk_put(host->clk); +err_exit1: + lpc32xx_wp_enable(host); + gpio_free(host->ncfg->wp_gpio); + + return res; +} + +/* + * Remove NAND device + */ +static int lpc32xx_nand_remove(struct platform_device *pdev) +{ + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + struct mtd_info *mtd = &host->mtd; + + nand_release(mtd); + free_irq(host->irq, host); + if (use_dma) + dma_release_channel(host->dma_chan); + + clk_disable(host->clk); + clk_put(host->clk); + + lpc32xx_wp_enable(host); + gpio_free(host->ncfg->wp_gpio); + + return 0; +} + +#ifdef CONFIG_PM +static int lpc32xx_nand_resume(struct platform_device *pdev) +{ + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + + /* Re-enable NAND clock */ + clk_enable(host->clk); + + /* Fresh init of NAND controller */ + lpc32xx_nand_setup(host); + + /* Disable write protect */ + lpc32xx_wp_disable(host); + + return 0; +} + +static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm) +{ + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + + /* Enable write protect for safety */ + lpc32xx_wp_enable(host); + + /* Disable clock */ + clk_disable(host->clk); + return 0; +} + +#else +#define lpc32xx_nand_resume NULL +#define lpc32xx_nand_suspend NULL +#endif + +static const struct of_device_id lpc32xx_nand_match[] = { + { .compatible = "nxp,lpc3220-mlc" }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, lpc32xx_nand_match); + +static struct platform_driver lpc32xx_nand_driver = { + .probe = lpc32xx_nand_probe, + .remove = lpc32xx_nand_remove, + .resume = lpc32xx_nand_resume, + .suspend = lpc32xx_nand_suspend, + .driver = { + .name = DRV_NAME, + .of_match_table = lpc32xx_nand_match, + }, +}; + +module_platform_driver(lpc32xx_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); +MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX MLC controller"); diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/lpc32xx_slc.c new file mode 100644 index 000000000..abfec1386 --- /dev/null +++ b/drivers/mtd/nand/lpc32xx_slc.c @@ -0,0 +1,1011 @@ +/* + * NXP LPC32XX NAND SLC driver + * + * Authors: + * Kevin Wells <kevin.wells@nxp.com> + * Roland Stigge <stigge@antcom.de> + * + * Copyright © 2011 NXP Semiconductors + * Copyright © 2012 Roland Stigge + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/mm.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include <linux/of_mtd.h> +#include <linux/of_gpio.h> +#include <linux/mtd/lpc32xx_slc.h> + +#define LPC32XX_MODNAME "lpc32xx-nand" + +/********************************************************************** +* SLC NAND controller register offsets +**********************************************************************/ + +#define SLC_DATA(x) (x + 0x000) +#define SLC_ADDR(x) (x + 0x004) +#define SLC_CMD(x) (x + 0x008) +#define SLC_STOP(x) (x + 0x00C) +#define SLC_CTRL(x) (x + 0x010) +#define SLC_CFG(x) (x + 0x014) +#define SLC_STAT(x) (x + 0x018) +#define SLC_INT_STAT(x) (x + 0x01C) +#define SLC_IEN(x) (x + 0x020) +#define SLC_ISR(x) (x + 0x024) +#define SLC_ICR(x) (x + 0x028) +#define SLC_TAC(x) (x + 0x02C) +#define SLC_TC(x) (x + 0x030) +#define SLC_ECC(x) (x + 0x034) +#define SLC_DMA_DATA(x) (x + 0x038) + +/********************************************************************** +* slc_ctrl register definitions +**********************************************************************/ +#define SLCCTRL_SW_RESET (1 << 2) /* Reset the NAND controller bit */ +#define SLCCTRL_ECC_CLEAR (1 << 1) /* Reset ECC bit */ +#define SLCCTRL_DMA_START (1 << 0) /* Start DMA channel bit */ + +/********************************************************************** +* slc_cfg register definitions +**********************************************************************/ +#define SLCCFG_CE_LOW (1 << 5) /* Force CE low bit */ +#define SLCCFG_DMA_ECC (1 << 4) /* Enable DMA ECC bit */ +#define SLCCFG_ECC_EN (1 << 3) /* ECC enable bit */ +#define SLCCFG_DMA_BURST (1 << 2) /* DMA burst bit */ +#define SLCCFG_DMA_DIR (1 << 1) /* DMA write(0)/read(1) bit */ +#define SLCCFG_WIDTH (1 << 0) /* External device width, 0=8bit */ + +/********************************************************************** +* slc_stat register definitions +**********************************************************************/ +#define SLCSTAT_DMA_FIFO (1 << 2) /* DMA FIFO has data bit */ +#define SLCSTAT_SLC_FIFO (1 << 1) /* SLC FIFO has data bit */ +#define SLCSTAT_NAND_READY (1 << 0) /* NAND device is ready bit */ + +/********************************************************************** +* slc_int_stat, slc_ien, slc_isr, and slc_icr register definitions +**********************************************************************/ +#define SLCSTAT_INT_TC (1 << 1) /* Transfer count bit */ +#define SLCSTAT_INT_RDY_EN (1 << 0) /* Ready interrupt bit */ + +/********************************************************************** +* slc_tac register definitions +**********************************************************************/ +/* Clock setting for RDY write sample wait time in 2*n clocks */ +#define SLCTAC_WDR(n) (((n) & 0xF) << 28) +/* Write pulse width in clock cycles, 1 to 16 clocks */ +#define SLCTAC_WWIDTH(n) (((n) & 0xF) << 24) +/* Write hold time of control and data signals, 1 to 16 clocks */ +#define SLCTAC_WHOLD(n) (((n) & 0xF) << 20) +/* Write setup time of control and data signals, 1 to 16 clocks */ +#define SLCTAC_WSETUP(n) (((n) & 0xF) << 16) +/* Clock setting for RDY read sample wait time in 2*n clocks */ +#define SLCTAC_RDR(n) (((n) & 0xF) << 12) +/* Read pulse width in clock cycles, 1 to 16 clocks */ +#define SLCTAC_RWIDTH(n) (((n) & 0xF) << 8) +/* Read hold time of control and data signals, 1 to 16 clocks */ +#define SLCTAC_RHOLD(n) (((n) & 0xF) << 4) +/* Read setup time of control and data signals, 1 to 16 clocks */ +#define SLCTAC_RSETUP(n) (((n) & 0xF) << 0) + +/********************************************************************** +* slc_ecc register definitions +**********************************************************************/ +/* ECC line party fetch macro */ +#define SLCECC_TO_LINEPAR(n) (((n) >> 6) & 0x7FFF) +#define SLCECC_TO_COLPAR(n) ((n) & 0x3F) + +/* + * DMA requires storage space for the DMA local buffer and the hardware ECC + * storage area. The DMA local buffer is only used if DMA mapping fails + * during runtime. + */ +#define LPC32XX_DMA_DATA_SIZE 4096 +#define LPC32XX_ECC_SAVE_SIZE ((4096 / 256) * 4) + +/* Number of bytes used for ECC stored in NAND per 256 bytes */ +#define LPC32XX_SLC_DEV_ECC_BYTES 3 + +/* + * If the NAND base clock frequency can't be fetched, this frequency will be + * used instead as the base. This rate is used to setup the timing registers + * used for NAND accesses. + */ +#define LPC32XX_DEF_BUS_RATE 133250000 + +/* Milliseconds for DMA FIFO timeout (unlikely anyway) */ +#define LPC32XX_DMA_TIMEOUT 100 + +/* + * NAND ECC Layout for small page NAND devices + * Note: For large and huge page devices, the default layouts are used + */ +static struct nand_ecclayout lpc32xx_nand_oob_16 = { + .eccbytes = 6, + .eccpos = {10, 11, 12, 13, 14, 15}, + .oobfree = { + { .offset = 0, .length = 4 }, + { .offset = 6, .length = 4 }, + }, +}; + +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +/* + * Small page FLASH BBT descriptors, marker at offset 0, version at offset 6 + * Note: Large page devices used the default layout + */ +static struct nand_bbt_descr bbt_smallpage_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 0, + .len = 4, + .veroffs = 6, + .maxblocks = 4, + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_smallpage_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 0, + .len = 4, + .veroffs = 6, + .maxblocks = 4, + .pattern = mirror_pattern +}; + +/* + * NAND platform configuration structure + */ +struct lpc32xx_nand_cfg_slc { + uint32_t wdr_clks; + uint32_t wwidth; + uint32_t whold; + uint32_t wsetup; + uint32_t rdr_clks; + uint32_t rwidth; + uint32_t rhold; + uint32_t rsetup; + bool use_bbt; + int wp_gpio; + struct mtd_partition *parts; + unsigned num_parts; +}; + +struct lpc32xx_nand_host { + struct nand_chip nand_chip; + struct lpc32xx_slc_platform_data *pdata; + struct clk *clk; + struct mtd_info mtd; + void __iomem *io_base; + struct lpc32xx_nand_cfg_slc *ncfg; + + struct completion comp; + struct dma_chan *dma_chan; + uint32_t dma_buf_len; + struct dma_slave_config dma_slave_config; + struct scatterlist sgl; + + /* + * DMA and CPU addresses of ECC work area and data buffer + */ + uint32_t *ecc_buf; + uint8_t *data_buf; + dma_addr_t io_base_dma; +}; + +static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host) +{ + uint32_t clkrate, tmp; + + /* Reset SLC controller */ + writel(SLCCTRL_SW_RESET, SLC_CTRL(host->io_base)); + udelay(1000); + + /* Basic setup */ + writel(0, SLC_CFG(host->io_base)); + writel(0, SLC_IEN(host->io_base)); + writel((SLCSTAT_INT_TC | SLCSTAT_INT_RDY_EN), + SLC_ICR(host->io_base)); + + /* Get base clock for SLC block */ + clkrate = clk_get_rate(host->clk); + if (clkrate == 0) + clkrate = LPC32XX_DEF_BUS_RATE; + + /* Compute clock setup values */ + tmp = SLCTAC_WDR(host->ncfg->wdr_clks) | + SLCTAC_WWIDTH(1 + (clkrate / host->ncfg->wwidth)) | + SLCTAC_WHOLD(1 + (clkrate / host->ncfg->whold)) | + SLCTAC_WSETUP(1 + (clkrate / host->ncfg->wsetup)) | + SLCTAC_RDR(host->ncfg->rdr_clks) | + SLCTAC_RWIDTH(1 + (clkrate / host->ncfg->rwidth)) | + SLCTAC_RHOLD(1 + (clkrate / host->ncfg->rhold)) | + SLCTAC_RSETUP(1 + (clkrate / host->ncfg->rsetup)); + writel(tmp, SLC_TAC(host->io_base)); +} + +/* + * Hardware specific access to control lines + */ +static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + uint32_t tmp; + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + + /* Does CE state need to be changed? */ + tmp = readl(SLC_CFG(host->io_base)); + if (ctrl & NAND_NCE) + tmp |= SLCCFG_CE_LOW; + else + tmp &= ~SLCCFG_CE_LOW; + writel(tmp, SLC_CFG(host->io_base)); + + if (cmd != NAND_CMD_NONE) { + if (ctrl & NAND_CLE) + writel(cmd, SLC_CMD(host->io_base)); + else + writel(cmd, SLC_ADDR(host->io_base)); + } +} + +/* + * Read the Device Ready pin + */ +static int lpc32xx_nand_device_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + int rdy = 0; + + if ((readl(SLC_STAT(host->io_base)) & SLCSTAT_NAND_READY) != 0) + rdy = 1; + + return rdy; +} + +/* + * Enable NAND write protect + */ +static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host) +{ + if (gpio_is_valid(host->ncfg->wp_gpio)) + gpio_set_value(host->ncfg->wp_gpio, 0); +} + +/* + * Disable NAND write protect + */ +static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host) +{ + if (gpio_is_valid(host->ncfg->wp_gpio)) + gpio_set_value(host->ncfg->wp_gpio, 1); +} + +/* + * Prepares SLC for transfers with H/W ECC enabled + */ +static void lpc32xx_nand_ecc_enable(struct mtd_info *mtd, int mode) +{ + /* Hardware ECC is enabled automatically in hardware as needed */ +} + +/* + * Calculates the ECC for the data + */ +static int lpc32xx_nand_ecc_calculate(struct mtd_info *mtd, + const unsigned char *buf, + unsigned char *code) +{ + /* + * ECC is calculated automatically in hardware during syndrome read + * and write operations, so it doesn't need to be calculated here. + */ + return 0; +} + +/* + * Read a single byte from NAND device + */ +static uint8_t lpc32xx_nand_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + + return (uint8_t)readl(SLC_DATA(host->io_base)); +} + +/* + * Simple device read without ECC + */ +static void lpc32xx_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + + /* Direct device read with no ECC */ + while (len-- > 0) + *buf++ = (uint8_t)readl(SLC_DATA(host->io_base)); +} + +/* + * Simple device write without ECC + */ +static void lpc32xx_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + + /* Direct device write with no ECC */ + while (len-- > 0) + writel((uint32_t)*buf++, SLC_DATA(host->io_base)); +} + +/* + * Read the OOB data from the device without ECC using FIFO method + */ +static int lpc32xx_nand_read_oob_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +/* + * Write the OOB data to the device without ECC using FIFO method + */ +static int lpc32xx_nand_write_oob_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + int status; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + /* Send command to program the OOB data */ + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/* + * Fills in the ECC fields in the OOB buffer with the hardware generated ECC + */ +static void lpc32xx_slc_ecc_copy(uint8_t *spare, const uint32_t *ecc, int count) +{ + int i; + + for (i = 0; i < (count * 3); i += 3) { + uint32_t ce = ecc[i / 3]; + ce = ~(ce << 2) & 0xFFFFFF; + spare[i + 2] = (uint8_t)(ce & 0xFF); + ce >>= 8; + spare[i + 1] = (uint8_t)(ce & 0xFF); + ce >>= 8; + spare[i] = (uint8_t)(ce & 0xFF); + } +} + +static void lpc32xx_dma_complete_func(void *completion) +{ + complete(completion); +} + +static int lpc32xx_xmit_dma(struct mtd_info *mtd, dma_addr_t dma, + void *mem, int len, enum dma_transfer_direction dir) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + struct dma_async_tx_descriptor *desc; + int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; + int res; + + host->dma_slave_config.direction = dir; + host->dma_slave_config.src_addr = dma; + host->dma_slave_config.dst_addr = dma; + host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + host->dma_slave_config.src_maxburst = 4; + host->dma_slave_config.dst_maxburst = 4; + /* DMA controller does flow control: */ + host->dma_slave_config.device_fc = false; + if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) { + dev_err(mtd->dev.parent, "Failed to setup DMA slave\n"); + return -ENXIO; + } + + sg_init_one(&host->sgl, mem, len); + + res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + if (res != 1) { + dev_err(mtd->dev.parent, "Failed to map sg list\n"); + return -ENXIO; + } + desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir, + flags); + if (!desc) { + dev_err(mtd->dev.parent, "Failed to prepare slave sg\n"); + goto out1; + } + + init_completion(&host->comp); + desc->callback = lpc32xx_dma_complete_func; + desc->callback_param = &host->comp; + + dmaengine_submit(desc); + dma_async_issue_pending(host->dma_chan); + + wait_for_completion_timeout(&host->comp, msecs_to_jiffies(1000)); + + dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + + return 0; +out1: + dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, + DMA_BIDIRECTIONAL); + return -ENXIO; +} + +/* + * DMA read/write transfers with ECC support + */ +static int lpc32xx_xfer(struct mtd_info *mtd, uint8_t *buf, int eccsubpages, + int read) +{ + struct nand_chip *chip = mtd->priv; + struct lpc32xx_nand_host *host = chip->priv; + int i, status = 0; + unsigned long timeout; + int res; + enum dma_transfer_direction dir = + read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV; + uint8_t *dma_buf; + bool dma_mapped; + + if ((void *)buf <= high_memory) { + dma_buf = buf; + dma_mapped = true; + } else { + dma_buf = host->data_buf; + dma_mapped = false; + if (!read) + memcpy(host->data_buf, buf, mtd->writesize); + } + + if (read) { + writel(readl(SLC_CFG(host->io_base)) | + SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC | + SLCCFG_DMA_BURST, SLC_CFG(host->io_base)); + } else { + writel((readl(SLC_CFG(host->io_base)) | + SLCCFG_ECC_EN | SLCCFG_DMA_ECC | SLCCFG_DMA_BURST) & + ~SLCCFG_DMA_DIR, + SLC_CFG(host->io_base)); + } + + /* Clear initial ECC */ + writel(SLCCTRL_ECC_CLEAR, SLC_CTRL(host->io_base)); + + /* Transfer size is data area only */ + writel(mtd->writesize, SLC_TC(host->io_base)); + + /* Start transfer in the NAND controller */ + writel(readl(SLC_CTRL(host->io_base)) | SLCCTRL_DMA_START, + SLC_CTRL(host->io_base)); + + for (i = 0; i < chip->ecc.steps; i++) { + /* Data */ + res = lpc32xx_xmit_dma(mtd, SLC_DMA_DATA(host->io_base_dma), + dma_buf + i * chip->ecc.size, + mtd->writesize / chip->ecc.steps, dir); + if (res) + return res; + + /* Always _read_ ECC */ + if (i == chip->ecc.steps - 1) + break; + if (!read) /* ECC availability delayed on write */ + udelay(10); + res = lpc32xx_xmit_dma(mtd, SLC_ECC(host->io_base_dma), + &host->ecc_buf[i], 4, DMA_DEV_TO_MEM); + if (res) + return res; + } + + /* + * According to NXP, the DMA can be finished here, but the NAND + * controller may still have buffered data. After porting to using the + * dmaengine DMA driver (amba-pl080), the condition (DMA_FIFO empty) + * appears to be always true, according to tests. Keeping the check for + * safety reasons for now. + */ + if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) { + dev_warn(mtd->dev.parent, "FIFO not empty!\n"); + timeout = jiffies + msecs_to_jiffies(LPC32XX_DMA_TIMEOUT); + while ((readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) && + time_before(jiffies, timeout)) + cpu_relax(); + if (!time_before(jiffies, timeout)) { + dev_err(mtd->dev.parent, "FIFO held data too long\n"); + status = -EIO; + } + } + + /* Read last calculated ECC value */ + if (!read) + udelay(10); + host->ecc_buf[chip->ecc.steps - 1] = + readl(SLC_ECC(host->io_base)); + + /* Flush DMA */ + dmaengine_terminate_all(host->dma_chan); + + if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO || + readl(SLC_TC(host->io_base))) { + /* Something is left in the FIFO, something is wrong */ + dev_err(mtd->dev.parent, "DMA FIFO failure\n"); + status = -EIO; + } + + /* Stop DMA & HW ECC */ + writel(readl(SLC_CTRL(host->io_base)) & ~SLCCTRL_DMA_START, + SLC_CTRL(host->io_base)); + writel(readl(SLC_CFG(host->io_base)) & + ~(SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC | + SLCCFG_DMA_BURST), SLC_CFG(host->io_base)); + + if (!dma_mapped && read) + memcpy(buf, host->data_buf, mtd->writesize); + + return status; +} + +/* + * Read the data and OOB data from the device, use ECC correction with the + * data, disable ECC for the OOB data + */ +static int lpc32xx_nand_read_page_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + struct lpc32xx_nand_host *host = chip->priv; + int stat, i, status; + uint8_t *oobecc, tmpecc[LPC32XX_ECC_SAVE_SIZE]; + + /* Issue read command */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + /* Read data and oob, calculate ECC */ + status = lpc32xx_xfer(mtd, buf, chip->ecc.steps, 1); + + /* Get OOB data */ + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + /* Convert to stored ECC format */ + lpc32xx_slc_ecc_copy(tmpecc, (uint32_t *) host->ecc_buf, chip->ecc.steps); + + /* Pointer to ECC data retrieved from NAND spare area */ + oobecc = chip->oob_poi + chip->ecc.layout->eccpos[0]; + + for (i = 0; i < chip->ecc.steps; i++) { + stat = chip->ecc.correct(mtd, buf, oobecc, + &tmpecc[i * chip->ecc.bytes]); + if (stat < 0) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += stat; + + buf += chip->ecc.size; + oobecc += chip->ecc.bytes; + } + + return status; +} + +/* + * Read the data and OOB data from the device, no ECC correction with the + * data or OOB data + */ +static int lpc32xx_nand_read_page_raw_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, + uint8_t *buf, int oob_required, + int page) +{ + /* Issue read command */ + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + /* Raw reads can just use the FIFO interface */ + chip->read_buf(mtd, buf, chip->ecc.size * chip->ecc.steps); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +/* + * Write the data and OOB data to the device, use ECC with the data, + * disable ECC for the OOB data + */ +static int lpc32xx_nand_write_page_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + struct lpc32xx_nand_host *host = chip->priv; + uint8_t *pb = chip->oob_poi + chip->ecc.layout->eccpos[0]; + int error; + + /* Write data, calculate ECC on outbound data */ + error = lpc32xx_xfer(mtd, (uint8_t *)buf, chip->ecc.steps, 0); + if (error) + return error; + + /* + * The calculated ECC needs some manual work done to it before + * committing it to NAND. Process the calculated ECC and place + * the resultant values directly into the OOB buffer. */ + lpc32xx_slc_ecc_copy(pb, (uint32_t *)host->ecc_buf, chip->ecc.steps); + + /* Write ECC data to device */ + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +/* + * Write the data and OOB data to the device, no ECC correction with the + * data or OOB data + */ +static int lpc32xx_nand_write_page_raw_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, + int oob_required) +{ + /* Raw writes can just use the FIFO interface */ + chip->write_buf(mtd, buf, chip->ecc.size * chip->ecc.steps); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +static int lpc32xx_nand_dma_setup(struct lpc32xx_nand_host *host) +{ + struct mtd_info *mtd = &host->mtd; + dma_cap_mask_t mask; + + if (!host->pdata || !host->pdata->dma_filter) { + dev_err(mtd->dev.parent, "no DMA platform data\n"); + return -ENOENT; + } + + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + host->dma_chan = dma_request_channel(mask, host->pdata->dma_filter, + "nand-slc"); + if (!host->dma_chan) { + dev_err(mtd->dev.parent, "Failed to request DMA channel\n"); + return -EBUSY; + } + + return 0; +} + +static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev) +{ + struct lpc32xx_nand_cfg_slc *ncfg; + struct device_node *np = dev->of_node; + + ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); + if (!ncfg) + return NULL; + + of_property_read_u32(np, "nxp,wdr-clks", &ncfg->wdr_clks); + of_property_read_u32(np, "nxp,wwidth", &ncfg->wwidth); + of_property_read_u32(np, "nxp,whold", &ncfg->whold); + of_property_read_u32(np, "nxp,wsetup", &ncfg->wsetup); + of_property_read_u32(np, "nxp,rdr-clks", &ncfg->rdr_clks); + of_property_read_u32(np, "nxp,rwidth", &ncfg->rwidth); + of_property_read_u32(np, "nxp,rhold", &ncfg->rhold); + of_property_read_u32(np, "nxp,rsetup", &ncfg->rsetup); + + if (!ncfg->wdr_clks || !ncfg->wwidth || !ncfg->whold || + !ncfg->wsetup || !ncfg->rdr_clks || !ncfg->rwidth || + !ncfg->rhold || !ncfg->rsetup) { + dev_err(dev, "chip parameters not specified correctly\n"); + return NULL; + } + + ncfg->use_bbt = of_get_nand_on_flash_bbt(np); + ncfg->wp_gpio = of_get_named_gpio(np, "gpios", 0); + + return ncfg; +} + +/* + * Probe for NAND controller + */ +static int lpc32xx_nand_probe(struct platform_device *pdev) +{ + struct lpc32xx_nand_host *host; + struct mtd_info *mtd; + struct nand_chip *chip; + struct resource *rc; + struct mtd_part_parser_data ppdata = {}; + int res; + + rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (rc == NULL) { + dev_err(&pdev->dev, "No memory resource found for device\n"); + return -EBUSY; + } + + /* Allocate memory for the device structure (and zero it) */ + host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + host->io_base_dma = rc->start; + + host->io_base = devm_ioremap_resource(&pdev->dev, rc); + if (IS_ERR(host->io_base)) + return PTR_ERR(host->io_base); + + if (pdev->dev.of_node) + host->ncfg = lpc32xx_parse_dt(&pdev->dev); + if (!host->ncfg) { + dev_err(&pdev->dev, + "Missing or bad NAND config from device tree\n"); + return -ENOENT; + } + if (host->ncfg->wp_gpio == -EPROBE_DEFER) + return -EPROBE_DEFER; + if (gpio_is_valid(host->ncfg->wp_gpio) && devm_gpio_request(&pdev->dev, + host->ncfg->wp_gpio, "NAND WP")) { + dev_err(&pdev->dev, "GPIO not available\n"); + return -EBUSY; + } + lpc32xx_wp_disable(host); + + host->pdata = dev_get_platdata(&pdev->dev); + + mtd = &host->mtd; + chip = &host->nand_chip; + chip->priv = host; + mtd->priv = chip; + mtd->owner = THIS_MODULE; + mtd->dev.parent = &pdev->dev; + + /* Get NAND clock */ + host->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(host->clk)) { + dev_err(&pdev->dev, "Clock failure\n"); + res = -ENOENT; + goto err_exit1; + } + clk_enable(host->clk); + + /* Set NAND IO addresses and command/ready functions */ + chip->IO_ADDR_R = SLC_DATA(host->io_base); + chip->IO_ADDR_W = SLC_DATA(host->io_base); + chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl; + chip->dev_ready = lpc32xx_nand_device_ready; + chip->chip_delay = 20; /* 20us command delay time */ + + /* Init NAND controller */ + lpc32xx_nand_setup(host); + + platform_set_drvdata(pdev, host); + + /* NAND callbacks for LPC32xx SLC hardware */ + chip->ecc.mode = NAND_ECC_HW_SYNDROME; + chip->read_byte = lpc32xx_nand_read_byte; + chip->read_buf = lpc32xx_nand_read_buf; + chip->write_buf = lpc32xx_nand_write_buf; + chip->ecc.read_page_raw = lpc32xx_nand_read_page_raw_syndrome; + chip->ecc.read_page = lpc32xx_nand_read_page_syndrome; + chip->ecc.write_page_raw = lpc32xx_nand_write_page_raw_syndrome; + chip->ecc.write_page = lpc32xx_nand_write_page_syndrome; + chip->ecc.write_oob = lpc32xx_nand_write_oob_syndrome; + chip->ecc.read_oob = lpc32xx_nand_read_oob_syndrome; + chip->ecc.calculate = lpc32xx_nand_ecc_calculate; + chip->ecc.correct = nand_correct_data; + chip->ecc.strength = 1; + chip->ecc.hwctl = lpc32xx_nand_ecc_enable; + + /* + * Allocate a large enough buffer for a single huge page plus + * extra space for the spare area and ECC storage area + */ + host->dma_buf_len = LPC32XX_DMA_DATA_SIZE + LPC32XX_ECC_SAVE_SIZE; + host->data_buf = devm_kzalloc(&pdev->dev, host->dma_buf_len, + GFP_KERNEL); + if (host->data_buf == NULL) { + res = -ENOMEM; + goto err_exit2; + } + + res = lpc32xx_nand_dma_setup(host); + if (res) { + res = -EIO; + goto err_exit2; + } + + /* Find NAND device */ + if (nand_scan_ident(mtd, 1, NULL)) { + res = -ENXIO; + goto err_exit3; + } + + /* OOB and ECC CPU and DMA work areas */ + host->ecc_buf = (uint32_t *)(host->data_buf + LPC32XX_DMA_DATA_SIZE); + + /* + * Small page FLASH has a unique OOB layout, but large and huge + * page FLASH use the standard layout. Small page FLASH uses a + * custom BBT marker layout. + */ + if (mtd->writesize <= 512) + chip->ecc.layout = &lpc32xx_nand_oob_16; + + /* These sizes remain the same regardless of page size */ + chip->ecc.size = 256; + chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES; + chip->ecc.prepad = chip->ecc.postpad = 0; + + /* Avoid extra scan if using BBT, setup BBT support */ + if (host->ncfg->use_bbt) { + chip->bbt_options |= NAND_BBT_USE_FLASH; + + /* + * Use a custom BBT marker setup for small page FLASH that + * won't interfere with the ECC layout. Large and huge page + * FLASH use the standard layout. + */ + if (mtd->writesize <= 512) { + chip->bbt_td = &bbt_smallpage_main_descr; + chip->bbt_md = &bbt_smallpage_mirror_descr; + } + } + + /* + * Fills out all the uninitialized function pointers with the defaults + */ + if (nand_scan_tail(mtd)) { + res = -ENXIO; + goto err_exit3; + } + + mtd->name = "nxp_lpc3220_slc"; + ppdata.of_node = pdev->dev.of_node; + res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts, + host->ncfg->num_parts); + if (!res) + return res; + + nand_release(mtd); + +err_exit3: + dma_release_channel(host->dma_chan); +err_exit2: + clk_disable(host->clk); +err_exit1: + lpc32xx_wp_enable(host); + + return res; +} + +/* + * Remove NAND device. + */ +static int lpc32xx_nand_remove(struct platform_device *pdev) +{ + uint32_t tmp; + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + struct mtd_info *mtd = &host->mtd; + + nand_release(mtd); + dma_release_channel(host->dma_chan); + + /* Force CE high */ + tmp = readl(SLC_CTRL(host->io_base)); + tmp &= ~SLCCFG_CE_LOW; + writel(tmp, SLC_CTRL(host->io_base)); + + clk_disable(host->clk); + lpc32xx_wp_enable(host); + + return 0; +} + +#ifdef CONFIG_PM +static int lpc32xx_nand_resume(struct platform_device *pdev) +{ + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + + /* Re-enable NAND clock */ + clk_enable(host->clk); + + /* Fresh init of NAND controller */ + lpc32xx_nand_setup(host); + + /* Disable write protect */ + lpc32xx_wp_disable(host); + + return 0; +} + +static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm) +{ + uint32_t tmp; + struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); + + /* Force CE high */ + tmp = readl(SLC_CTRL(host->io_base)); + tmp &= ~SLCCFG_CE_LOW; + writel(tmp, SLC_CTRL(host->io_base)); + + /* Enable write protect for safety */ + lpc32xx_wp_enable(host); + + /* Disable clock */ + clk_disable(host->clk); + + return 0; +} + +#else +#define lpc32xx_nand_resume NULL +#define lpc32xx_nand_suspend NULL +#endif + +static const struct of_device_id lpc32xx_nand_match[] = { + { .compatible = "nxp,lpc3220-slc" }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, lpc32xx_nand_match); + +static struct platform_driver lpc32xx_nand_driver = { + .probe = lpc32xx_nand_probe, + .remove = lpc32xx_nand_remove, + .resume = lpc32xx_nand_resume, + .suspend = lpc32xx_nand_suspend, + .driver = { + .name = LPC32XX_MODNAME, + .of_match_table = lpc32xx_nand_match, + }, +}; + +module_platform_driver(lpc32xx_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>"); +MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); +MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX SLC controller"); diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c new file mode 100644 index 000000000..1f12e5bfb --- /dev/null +++ b/drivers/mtd/nand/mpc5121_nfc.c @@ -0,0 +1,858 @@ +/* + * Copyright 2004-2008 Freescale Semiconductor, Inc. + * Copyright 2009 Semihalf. + * + * Approved as OSADL project by a majority of OSADL members and funded + * by OSADL membership fees in 2009; for details see www.osadl.org. + * + * Based on original driver from Freescale Semiconductor + * written by John Rigby <jrigby@freescale.com> on basis + * of drivers/mtd/nand/mxc_nand.c. Reworked and extended + * Piotr Ziecik <kosmo@semihalf.com>. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include <linux/module.h> +#include <linux/clk.h> +#include <linux/gfp.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> + +#include <asm/mpc5121.h> + +/* Addresses for NFC MAIN RAM BUFFER areas */ +#define NFC_MAIN_AREA(n) ((n) * 0x200) + +/* Addresses for NFC SPARE BUFFER areas */ +#define NFC_SPARE_BUFFERS 8 +#define NFC_SPARE_LEN 0x40 +#define NFC_SPARE_AREA(n) (0x1000 + ((n) * NFC_SPARE_LEN)) + +/* MPC5121 NFC registers */ +#define NFC_BUF_ADDR 0x1E04 +#define NFC_FLASH_ADDR 0x1E06 +#define NFC_FLASH_CMD 0x1E08 +#define NFC_CONFIG 0x1E0A +#define NFC_ECC_STATUS1 0x1E0C +#define NFC_ECC_STATUS2 0x1E0E +#define NFC_SPAS 0x1E10 +#define NFC_WRPROT 0x1E12 +#define NFC_NF_WRPRST 0x1E18 +#define NFC_CONFIG1 0x1E1A +#define NFC_CONFIG2 0x1E1C +#define NFC_UNLOCKSTART_BLK0 0x1E20 +#define NFC_UNLOCKEND_BLK0 0x1E22 +#define NFC_UNLOCKSTART_BLK1 0x1E24 +#define NFC_UNLOCKEND_BLK1 0x1E26 +#define NFC_UNLOCKSTART_BLK2 0x1E28 +#define NFC_UNLOCKEND_BLK2 0x1E2A +#define NFC_UNLOCKSTART_BLK3 0x1E2C +#define NFC_UNLOCKEND_BLK3 0x1E2E + +/* Bit Definitions: NFC_BUF_ADDR */ +#define NFC_RBA_MASK (7 << 0) +#define NFC_ACTIVE_CS_SHIFT 5 +#define NFC_ACTIVE_CS_MASK (3 << NFC_ACTIVE_CS_SHIFT) + +/* Bit Definitions: NFC_CONFIG */ +#define NFC_BLS_UNLOCKED (1 << 1) + +/* Bit Definitions: NFC_CONFIG1 */ +#define NFC_ECC_4BIT (1 << 0) +#define NFC_FULL_PAGE_DMA (1 << 1) +#define NFC_SPARE_ONLY (1 << 2) +#define NFC_ECC_ENABLE (1 << 3) +#define NFC_INT_MASK (1 << 4) +#define NFC_BIG_ENDIAN (1 << 5) +#define NFC_RESET (1 << 6) +#define NFC_CE (1 << 7) +#define NFC_ONE_CYCLE (1 << 8) +#define NFC_PPB_32 (0 << 9) +#define NFC_PPB_64 (1 << 9) +#define NFC_PPB_128 (2 << 9) +#define NFC_PPB_256 (3 << 9) +#define NFC_PPB_MASK (3 << 9) +#define NFC_FULL_PAGE_INT (1 << 11) + +/* Bit Definitions: NFC_CONFIG2 */ +#define NFC_COMMAND (1 << 0) +#define NFC_ADDRESS (1 << 1) +#define NFC_INPUT (1 << 2) +#define NFC_OUTPUT (1 << 3) +#define NFC_ID (1 << 4) +#define NFC_STATUS (1 << 5) +#define NFC_CMD_FAIL (1 << 15) +#define NFC_INT (1 << 15) + +/* Bit Definitions: NFC_WRPROT */ +#define NFC_WPC_LOCK_TIGHT (1 << 0) +#define NFC_WPC_LOCK (1 << 1) +#define NFC_WPC_UNLOCK (1 << 2) + +#define DRV_NAME "mpc5121_nfc" + +/* Timeouts */ +#define NFC_RESET_TIMEOUT 1000 /* 1 ms */ +#define NFC_TIMEOUT (HZ / 10) /* 1/10 s */ + +struct mpc5121_nfc_prv { + struct mtd_info mtd; + struct nand_chip chip; + int irq; + void __iomem *regs; + struct clk *clk; + wait_queue_head_t irq_waitq; + uint column; + int spareonly; + void __iomem *csreg; + struct device *dev; +}; + +static void mpc5121_nfc_done(struct mtd_info *mtd); + +/* Read NFC register */ +static inline u16 nfc_read(struct mtd_info *mtd, uint reg) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + + return in_be16(prv->regs + reg); +} + +/* Write NFC register */ +static inline void nfc_write(struct mtd_info *mtd, uint reg, u16 val) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + + out_be16(prv->regs + reg, val); +} + +/* Set bits in NFC register */ +static inline void nfc_set(struct mtd_info *mtd, uint reg, u16 bits) +{ + nfc_write(mtd, reg, nfc_read(mtd, reg) | bits); +} + +/* Clear bits in NFC register */ +static inline void nfc_clear(struct mtd_info *mtd, uint reg, u16 bits) +{ + nfc_write(mtd, reg, nfc_read(mtd, reg) & ~bits); +} + +/* Invoke address cycle */ +static inline void mpc5121_nfc_send_addr(struct mtd_info *mtd, u16 addr) +{ + nfc_write(mtd, NFC_FLASH_ADDR, addr); + nfc_write(mtd, NFC_CONFIG2, NFC_ADDRESS); + mpc5121_nfc_done(mtd); +} + +/* Invoke command cycle */ +static inline void mpc5121_nfc_send_cmd(struct mtd_info *mtd, u16 cmd) +{ + nfc_write(mtd, NFC_FLASH_CMD, cmd); + nfc_write(mtd, NFC_CONFIG2, NFC_COMMAND); + mpc5121_nfc_done(mtd); +} + +/* Send data from NFC buffers to NAND flash */ +static inline void mpc5121_nfc_send_prog_page(struct mtd_info *mtd) +{ + nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK); + nfc_write(mtd, NFC_CONFIG2, NFC_INPUT); + mpc5121_nfc_done(mtd); +} + +/* Receive data from NAND flash */ +static inline void mpc5121_nfc_send_read_page(struct mtd_info *mtd) +{ + nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK); + nfc_write(mtd, NFC_CONFIG2, NFC_OUTPUT); + mpc5121_nfc_done(mtd); +} + +/* Receive ID from NAND flash */ +static inline void mpc5121_nfc_send_read_id(struct mtd_info *mtd) +{ + nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK); + nfc_write(mtd, NFC_CONFIG2, NFC_ID); + mpc5121_nfc_done(mtd); +} + +/* Receive status from NAND flash */ +static inline void mpc5121_nfc_send_read_status(struct mtd_info *mtd) +{ + nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK); + nfc_write(mtd, NFC_CONFIG2, NFC_STATUS); + mpc5121_nfc_done(mtd); +} + +/* NFC interrupt handler */ +static irqreturn_t mpc5121_nfc_irq(int irq, void *data) +{ + struct mtd_info *mtd = data; + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + + nfc_set(mtd, NFC_CONFIG1, NFC_INT_MASK); + wake_up(&prv->irq_waitq); + + return IRQ_HANDLED; +} + +/* Wait for operation complete */ +static void mpc5121_nfc_done(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + int rv; + + if ((nfc_read(mtd, NFC_CONFIG2) & NFC_INT) == 0) { + nfc_clear(mtd, NFC_CONFIG1, NFC_INT_MASK); + rv = wait_event_timeout(prv->irq_waitq, + (nfc_read(mtd, NFC_CONFIG2) & NFC_INT), NFC_TIMEOUT); + + if (!rv) + dev_warn(prv->dev, + "Timeout while waiting for interrupt.\n"); + } + + nfc_clear(mtd, NFC_CONFIG2, NFC_INT); +} + +/* Do address cycle(s) */ +static void mpc5121_nfc_addr_cycle(struct mtd_info *mtd, int column, int page) +{ + struct nand_chip *chip = mtd->priv; + u32 pagemask = chip->pagemask; + + if (column != -1) { + mpc5121_nfc_send_addr(mtd, column); + if (mtd->writesize > 512) + mpc5121_nfc_send_addr(mtd, column >> 8); + } + + if (page != -1) { + do { + mpc5121_nfc_send_addr(mtd, page & 0xFF); + page >>= 8; + pagemask >>= 8; + } while (pagemask); + } +} + +/* Control chip select signals */ +static void mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip) +{ + if (chip < 0) { + nfc_clear(mtd, NFC_CONFIG1, NFC_CE); + return; + } + + nfc_clear(mtd, NFC_BUF_ADDR, NFC_ACTIVE_CS_MASK); + nfc_set(mtd, NFC_BUF_ADDR, (chip << NFC_ACTIVE_CS_SHIFT) & + NFC_ACTIVE_CS_MASK); + nfc_set(mtd, NFC_CONFIG1, NFC_CE); +} + +/* Init external chip select logic on ADS5121 board */ +static int ads5121_chipselect_init(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + struct device_node *dn; + + dn = of_find_compatible_node(NULL, NULL, "fsl,mpc5121ads-cpld"); + if (dn) { + prv->csreg = of_iomap(dn, 0); + of_node_put(dn); + if (!prv->csreg) + return -ENOMEM; + + /* CPLD Register 9 controls NAND /CE Lines */ + prv->csreg += 9; + return 0; + } + + return -EINVAL; +} + +/* Control chips select signal on ADS5121 board */ +static void ads5121_select_chip(struct mtd_info *mtd, int chip) +{ + struct nand_chip *nand = mtd->priv; + struct mpc5121_nfc_prv *prv = nand->priv; + u8 v; + + v = in_8(prv->csreg); + v |= 0x0F; + + if (chip >= 0) { + mpc5121_nfc_select_chip(mtd, 0); + v &= ~(1 << chip); + } else + mpc5121_nfc_select_chip(mtd, -1); + + out_8(prv->csreg, v); +} + +/* Read NAND Ready/Busy signal */ +static int mpc5121_nfc_dev_ready(struct mtd_info *mtd) +{ + /* + * NFC handles ready/busy signal internally. Therefore, this function + * always returns status as ready. + */ + return 1; +} + +/* Write command to NAND flash */ +static void mpc5121_nfc_command(struct mtd_info *mtd, unsigned command, + int column, int page) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + + prv->column = (column >= 0) ? column : 0; + prv->spareonly = 0; + + switch (command) { + case NAND_CMD_PAGEPROG: + mpc5121_nfc_send_prog_page(mtd); + break; + /* + * NFC does not support sub-page reads and writes, + * so emulate them using full page transfers. + */ + case NAND_CMD_READ0: + column = 0; + break; + + case NAND_CMD_READ1: + prv->column += 256; + command = NAND_CMD_READ0; + column = 0; + break; + + case NAND_CMD_READOOB: + prv->spareonly = 1; + command = NAND_CMD_READ0; + column = 0; + break; + + case NAND_CMD_SEQIN: + mpc5121_nfc_command(mtd, NAND_CMD_READ0, column, page); + column = 0; + break; + + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_READID: + case NAND_CMD_STATUS: + break; + + default: + return; + } + + mpc5121_nfc_send_cmd(mtd, command); + mpc5121_nfc_addr_cycle(mtd, column, page); + + switch (command) { + case NAND_CMD_READ0: + if (mtd->writesize > 512) + mpc5121_nfc_send_cmd(mtd, NAND_CMD_READSTART); + mpc5121_nfc_send_read_page(mtd); + break; + + case NAND_CMD_READID: + mpc5121_nfc_send_read_id(mtd); + break; + + case NAND_CMD_STATUS: + mpc5121_nfc_send_read_status(mtd); + if (chip->options & NAND_BUSWIDTH_16) + prv->column = 1; + else + prv->column = 0; + break; + } +} + +/* Copy data from/to NFC spare buffers. */ +static void mpc5121_nfc_copy_spare(struct mtd_info *mtd, uint offset, + u8 *buffer, uint size, int wr) +{ + struct nand_chip *nand = mtd->priv; + struct mpc5121_nfc_prv *prv = nand->priv; + uint o, s, sbsize, blksize; + + /* + * NAND spare area is available through NFC spare buffers. + * The NFC divides spare area into (page_size / 512) chunks. + * Each chunk is placed into separate spare memory area, using + * first (spare_size / num_of_chunks) bytes of the buffer. + * + * For NAND device in which the spare area is not divided fully + * by the number of chunks, number of used bytes in each spare + * buffer is rounded down to the nearest even number of bytes, + * and all remaining bytes are added to the last used spare area. + * + * For more information read section 26.6.10 of MPC5121e + * Microcontroller Reference Manual, Rev. 3. + */ + + /* Calculate number of valid bytes in each spare buffer */ + sbsize = (mtd->oobsize / (mtd->writesize / 512)) & ~1; + + while (size) { + /* Calculate spare buffer number */ + s = offset / sbsize; + if (s > NFC_SPARE_BUFFERS - 1) + s = NFC_SPARE_BUFFERS - 1; + + /* + * Calculate offset to requested data block in selected spare + * buffer and its size. + */ + o = offset - (s * sbsize); + blksize = min(sbsize - o, size); + + if (wr) + memcpy_toio(prv->regs + NFC_SPARE_AREA(s) + o, + buffer, blksize); + else + memcpy_fromio(buffer, + prv->regs + NFC_SPARE_AREA(s) + o, blksize); + + buffer += blksize; + offset += blksize; + size -= blksize; + }; +} + +/* Copy data from/to NFC main and spare buffers */ +static void mpc5121_nfc_buf_copy(struct mtd_info *mtd, u_char *buf, int len, + int wr) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + uint c = prv->column; + uint l; + + /* Handle spare area access */ + if (prv->spareonly || c >= mtd->writesize) { + /* Calculate offset from beginning of spare area */ + if (c >= mtd->writesize) + c -= mtd->writesize; + + prv->column += len; + mpc5121_nfc_copy_spare(mtd, c, buf, len, wr); + return; + } + + /* + * Handle main area access - limit copy length to prevent + * crossing main/spare boundary. + */ + l = min((uint)len, mtd->writesize - c); + prv->column += l; + + if (wr) + memcpy_toio(prv->regs + NFC_MAIN_AREA(0) + c, buf, l); + else + memcpy_fromio(buf, prv->regs + NFC_MAIN_AREA(0) + c, l); + + /* Handle crossing main/spare boundary */ + if (l != len) { + buf += l; + len -= l; + mpc5121_nfc_buf_copy(mtd, buf, len, wr); + } +} + +/* Read data from NFC buffers */ +static void mpc5121_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + mpc5121_nfc_buf_copy(mtd, buf, len, 0); +} + +/* Write data to NFC buffers */ +static void mpc5121_nfc_write_buf(struct mtd_info *mtd, + const u_char *buf, int len) +{ + mpc5121_nfc_buf_copy(mtd, (u_char *)buf, len, 1); +} + +/* Read byte from NFC buffers */ +static u8 mpc5121_nfc_read_byte(struct mtd_info *mtd) +{ + u8 tmp; + + mpc5121_nfc_read_buf(mtd, &tmp, sizeof(tmp)); + + return tmp; +} + +/* Read word from NFC buffers */ +static u16 mpc5121_nfc_read_word(struct mtd_info *mtd) +{ + u16 tmp; + + mpc5121_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp)); + + return tmp; +} + +/* + * Read NFC configuration from Reset Config Word + * + * NFC is configured during reset in basis of information stored + * in Reset Config Word. There is no other way to set NAND block + * size, spare size and bus width. + */ +static int mpc5121_nfc_read_hw_config(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + struct mpc512x_reset_module *rm; + struct device_node *rmnode; + uint rcw_pagesize = 0; + uint rcw_sparesize = 0; + uint rcw_width; + uint rcwh; + uint romloc, ps; + int ret = 0; + + rmnode = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-reset"); + if (!rmnode) { + dev_err(prv->dev, "Missing 'fsl,mpc5121-reset' " + "node in device tree!\n"); + return -ENODEV; + } + + rm = of_iomap(rmnode, 0); + if (!rm) { + dev_err(prv->dev, "Error mapping reset module node!\n"); + ret = -EBUSY; + goto out; + } + + rcwh = in_be32(&rm->rcwhr); + + /* Bit 6: NFC bus width */ + rcw_width = ((rcwh >> 6) & 0x1) ? 2 : 1; + + /* Bit 7: NFC Page/Spare size */ + ps = (rcwh >> 7) & 0x1; + + /* Bits [22:21]: ROM Location */ + romloc = (rcwh >> 21) & 0x3; + + /* Decode RCW bits */ + switch ((ps << 2) | romloc) { + case 0x00: + case 0x01: + rcw_pagesize = 512; + rcw_sparesize = 16; + break; + case 0x02: + case 0x03: + rcw_pagesize = 4096; + rcw_sparesize = 128; + break; + case 0x04: + case 0x05: + rcw_pagesize = 2048; + rcw_sparesize = 64; + break; + case 0x06: + case 0x07: + rcw_pagesize = 4096; + rcw_sparesize = 218; + break; + } + + mtd->writesize = rcw_pagesize; + mtd->oobsize = rcw_sparesize; + if (rcw_width == 2) + chip->options |= NAND_BUSWIDTH_16; + + dev_notice(prv->dev, "Configured for " + "%u-bit NAND, page size %u " + "with %u spare.\n", + rcw_width * 8, rcw_pagesize, + rcw_sparesize); + iounmap(rm); +out: + of_node_put(rmnode); + return ret; +} + +/* Free driver resources */ +static void mpc5121_nfc_free(struct device *dev, struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct mpc5121_nfc_prv *prv = chip->priv; + + if (prv->clk) + clk_disable_unprepare(prv->clk); + + if (prv->csreg) + iounmap(prv->csreg); +} + +static int mpc5121_nfc_probe(struct platform_device *op) +{ + struct device_node *rootnode, *dn = op->dev.of_node; + struct clk *clk; + struct device *dev = &op->dev; + struct mpc5121_nfc_prv *prv; + struct resource res; + struct mtd_info *mtd; + struct nand_chip *chip; + unsigned long regs_paddr, regs_size; + const __be32 *chips_no; + int resettime = 0; + int retval = 0; + int rev, len; + struct mtd_part_parser_data ppdata; + + /* + * Check SoC revision. This driver supports only NFC + * in MPC5121 revision 2 and MPC5123 revision 3. + */ + rev = (mfspr(SPRN_SVR) >> 4) & 0xF; + if ((rev != 2) && (rev != 3)) { + dev_err(dev, "SoC revision %u is not supported!\n", rev); + return -ENXIO; + } + + prv = devm_kzalloc(dev, sizeof(*prv), GFP_KERNEL); + if (!prv) + return -ENOMEM; + + mtd = &prv->mtd; + chip = &prv->chip; + + mtd->priv = chip; + chip->priv = prv; + prv->dev = dev; + + /* Read NFC configuration from Reset Config Word */ + retval = mpc5121_nfc_read_hw_config(mtd); + if (retval) { + dev_err(dev, "Unable to read NFC config!\n"); + return retval; + } + + prv->irq = irq_of_parse_and_map(dn, 0); + if (prv->irq == NO_IRQ) { + dev_err(dev, "Error mapping IRQ!\n"); + return -EINVAL; + } + + retval = of_address_to_resource(dn, 0, &res); + if (retval) { + dev_err(dev, "Error parsing memory region!\n"); + return retval; + } + + chips_no = of_get_property(dn, "chips", &len); + if (!chips_no || len != sizeof(*chips_no)) { + dev_err(dev, "Invalid/missing 'chips' property!\n"); + return -EINVAL; + } + + regs_paddr = res.start; + regs_size = resource_size(&res); + + if (!devm_request_mem_region(dev, regs_paddr, regs_size, DRV_NAME)) { + dev_err(dev, "Error requesting memory region!\n"); + return -EBUSY; + } + + prv->regs = devm_ioremap(dev, regs_paddr, regs_size); + if (!prv->regs) { + dev_err(dev, "Error mapping memory region!\n"); + return -ENOMEM; + } + + mtd->name = "MPC5121 NAND"; + ppdata.of_node = dn; + chip->dev_ready = mpc5121_nfc_dev_ready; + chip->cmdfunc = mpc5121_nfc_command; + chip->read_byte = mpc5121_nfc_read_byte; + chip->read_word = mpc5121_nfc_read_word; + chip->read_buf = mpc5121_nfc_read_buf; + chip->write_buf = mpc5121_nfc_write_buf; + chip->select_chip = mpc5121_nfc_select_chip; + chip->bbt_options = NAND_BBT_USE_FLASH; + chip->ecc.mode = NAND_ECC_SOFT; + + /* Support external chip-select logic on ADS5121 board */ + rootnode = of_find_node_by_path("/"); + if (of_device_is_compatible(rootnode, "fsl,mpc5121ads")) { + retval = ads5121_chipselect_init(mtd); + if (retval) { + dev_err(dev, "Chipselect init error!\n"); + of_node_put(rootnode); + return retval; + } + + chip->select_chip = ads5121_select_chip; + } + of_node_put(rootnode); + + /* Enable NFC clock */ + clk = devm_clk_get(dev, "ipg"); + if (IS_ERR(clk)) { + dev_err(dev, "Unable to acquire NFC clock!\n"); + retval = PTR_ERR(clk); + goto error; + } + retval = clk_prepare_enable(clk); + if (retval) { + dev_err(dev, "Unable to enable NFC clock!\n"); + goto error; + } + prv->clk = clk; + + /* Reset NAND Flash controller */ + nfc_set(mtd, NFC_CONFIG1, NFC_RESET); + while (nfc_read(mtd, NFC_CONFIG1) & NFC_RESET) { + if (resettime++ >= NFC_RESET_TIMEOUT) { + dev_err(dev, "Timeout while resetting NFC!\n"); + retval = -EINVAL; + goto error; + } + + udelay(1); + } + + /* Enable write to NFC memory */ + nfc_write(mtd, NFC_CONFIG, NFC_BLS_UNLOCKED); + + /* Enable write to all NAND pages */ + nfc_write(mtd, NFC_UNLOCKSTART_BLK0, 0x0000); + nfc_write(mtd, NFC_UNLOCKEND_BLK0, 0xFFFF); + nfc_write(mtd, NFC_WRPROT, NFC_WPC_UNLOCK); + + /* + * Setup NFC: + * - Big Endian transfers, + * - Interrupt after full page read/write. + */ + nfc_write(mtd, NFC_CONFIG1, NFC_BIG_ENDIAN | NFC_INT_MASK | + NFC_FULL_PAGE_INT); + + /* Set spare area size */ + nfc_write(mtd, NFC_SPAS, mtd->oobsize >> 1); + + init_waitqueue_head(&prv->irq_waitq); + retval = devm_request_irq(dev, prv->irq, &mpc5121_nfc_irq, 0, DRV_NAME, + mtd); + if (retval) { + dev_err(dev, "Error requesting IRQ!\n"); + goto error; + } + + /* Detect NAND chips */ + if (nand_scan(mtd, be32_to_cpup(chips_no))) { + dev_err(dev, "NAND Flash not found !\n"); + retval = -ENXIO; + goto error; + } + + /* Set erase block size */ + switch (mtd->erasesize / mtd->writesize) { + case 32: + nfc_set(mtd, NFC_CONFIG1, NFC_PPB_32); + break; + + case 64: + nfc_set(mtd, NFC_CONFIG1, NFC_PPB_64); + break; + + case 128: + nfc_set(mtd, NFC_CONFIG1, NFC_PPB_128); + break; + + case 256: + nfc_set(mtd, NFC_CONFIG1, NFC_PPB_256); + break; + + default: + dev_err(dev, "Unsupported NAND flash!\n"); + retval = -ENXIO; + goto error; + } + + dev_set_drvdata(dev, mtd); + + /* Register device in MTD */ + retval = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (retval) { + dev_err(dev, "Error adding MTD device!\n"); + goto error; + } + + return 0; +error: + mpc5121_nfc_free(dev, mtd); + return retval; +} + +static int mpc5121_nfc_remove(struct platform_device *op) +{ + struct device *dev = &op->dev; + struct mtd_info *mtd = dev_get_drvdata(dev); + + nand_release(mtd); + mpc5121_nfc_free(dev, mtd); + + return 0; +} + +static struct of_device_id mpc5121_nfc_match[] = { + { .compatible = "fsl,mpc5121-nfc", }, + {}, +}; + +static struct platform_driver mpc5121_nfc_driver = { + .probe = mpc5121_nfc_probe, + .remove = mpc5121_nfc_remove, + .driver = { + .name = DRV_NAME, + .of_match_table = mpc5121_nfc_match, + }, +}; + +module_platform_driver(mpc5121_nfc_driver); + +MODULE_AUTHOR("Freescale Semiconductor, Inc."); +MODULE_DESCRIPTION("MPC5121 NAND MTD driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c new file mode 100644 index 000000000..372e0e38f --- /dev/null +++ b/drivers/mtd/nand/mxc_nand.c @@ -0,0 +1,1649 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Sascha Hauer, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/completion.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_mtd.h> + +#include <asm/mach/flash.h> +#include <linux/platform_data/mtd-mxc_nand.h> + +#define DRIVER_NAME "mxc_nand" + +/* Addresses for NFC registers */ +#define NFC_V1_V2_BUF_SIZE (host->regs + 0x00) +#define NFC_V1_V2_BUF_ADDR (host->regs + 0x04) +#define NFC_V1_V2_FLASH_ADDR (host->regs + 0x06) +#define NFC_V1_V2_FLASH_CMD (host->regs + 0x08) +#define NFC_V1_V2_CONFIG (host->regs + 0x0a) +#define NFC_V1_V2_ECC_STATUS_RESULT (host->regs + 0x0c) +#define NFC_V1_V2_RSLTMAIN_AREA (host->regs + 0x0e) +#define NFC_V1_V2_RSLTSPARE_AREA (host->regs + 0x10) +#define NFC_V1_V2_WRPROT (host->regs + 0x12) +#define NFC_V1_UNLOCKSTART_BLKADDR (host->regs + 0x14) +#define NFC_V1_UNLOCKEND_BLKADDR (host->regs + 0x16) +#define NFC_V21_UNLOCKSTART_BLKADDR0 (host->regs + 0x20) +#define NFC_V21_UNLOCKSTART_BLKADDR1 (host->regs + 0x24) +#define NFC_V21_UNLOCKSTART_BLKADDR2 (host->regs + 0x28) +#define NFC_V21_UNLOCKSTART_BLKADDR3 (host->regs + 0x2c) +#define NFC_V21_UNLOCKEND_BLKADDR0 (host->regs + 0x22) +#define NFC_V21_UNLOCKEND_BLKADDR1 (host->regs + 0x26) +#define NFC_V21_UNLOCKEND_BLKADDR2 (host->regs + 0x2a) +#define NFC_V21_UNLOCKEND_BLKADDR3 (host->regs + 0x2e) +#define NFC_V1_V2_NF_WRPRST (host->regs + 0x18) +#define NFC_V1_V2_CONFIG1 (host->regs + 0x1a) +#define NFC_V1_V2_CONFIG2 (host->regs + 0x1c) + +#define NFC_V2_CONFIG1_ECC_MODE_4 (1 << 0) +#define NFC_V1_V2_CONFIG1_SP_EN (1 << 2) +#define NFC_V1_V2_CONFIG1_ECC_EN (1 << 3) +#define NFC_V1_V2_CONFIG1_INT_MSK (1 << 4) +#define NFC_V1_V2_CONFIG1_BIG (1 << 5) +#define NFC_V1_V2_CONFIG1_RST (1 << 6) +#define NFC_V1_V2_CONFIG1_CE (1 << 7) +#define NFC_V2_CONFIG1_ONE_CYCLE (1 << 8) +#define NFC_V2_CONFIG1_PPB(x) (((x) & 0x3) << 9) +#define NFC_V2_CONFIG1_FP_INT (1 << 11) + +#define NFC_V1_V2_CONFIG2_INT (1 << 15) + +/* + * Operation modes for the NFC. Valid for v1, v2 and v3 + * type controllers. + */ +#define NFC_CMD (1 << 0) +#define NFC_ADDR (1 << 1) +#define NFC_INPUT (1 << 2) +#define NFC_OUTPUT (1 << 3) +#define NFC_ID (1 << 4) +#define NFC_STATUS (1 << 5) + +#define NFC_V3_FLASH_CMD (host->regs_axi + 0x00) +#define NFC_V3_FLASH_ADDR0 (host->regs_axi + 0x04) + +#define NFC_V3_CONFIG1 (host->regs_axi + 0x34) +#define NFC_V3_CONFIG1_SP_EN (1 << 0) +#define NFC_V3_CONFIG1_RBA(x) (((x) & 0x7 ) << 4) + +#define NFC_V3_ECC_STATUS_RESULT (host->regs_axi + 0x38) + +#define NFC_V3_LAUNCH (host->regs_axi + 0x40) + +#define NFC_V3_WRPROT (host->regs_ip + 0x0) +#define NFC_V3_WRPROT_LOCK_TIGHT (1 << 0) +#define NFC_V3_WRPROT_LOCK (1 << 1) +#define NFC_V3_WRPROT_UNLOCK (1 << 2) +#define NFC_V3_WRPROT_BLS_UNLOCK (2 << 6) + +#define NFC_V3_WRPROT_UNLOCK_BLK_ADD0 (host->regs_ip + 0x04) + +#define NFC_V3_CONFIG2 (host->regs_ip + 0x24) +#define NFC_V3_CONFIG2_PS_512 (0 << 0) +#define NFC_V3_CONFIG2_PS_2048 (1 << 0) +#define NFC_V3_CONFIG2_PS_4096 (2 << 0) +#define NFC_V3_CONFIG2_ONE_CYCLE (1 << 2) +#define NFC_V3_CONFIG2_ECC_EN (1 << 3) +#define NFC_V3_CONFIG2_2CMD_PHASES (1 << 4) +#define NFC_V3_CONFIG2_NUM_ADDR_PHASE0 (1 << 5) +#define NFC_V3_CONFIG2_ECC_MODE_8 (1 << 6) +#define NFC_V3_CONFIG2_PPB(x, shift) (((x) & 0x3) << shift) +#define NFC_V3_CONFIG2_NUM_ADDR_PHASE1(x) (((x) & 0x3) << 12) +#define NFC_V3_CONFIG2_INT_MSK (1 << 15) +#define NFC_V3_CONFIG2_ST_CMD(x) (((x) & 0xff) << 24) +#define NFC_V3_CONFIG2_SPAS(x) (((x) & 0xff) << 16) + +#define NFC_V3_CONFIG3 (host->regs_ip + 0x28) +#define NFC_V3_CONFIG3_ADD_OP(x) (((x) & 0x3) << 0) +#define NFC_V3_CONFIG3_FW8 (1 << 3) +#define NFC_V3_CONFIG3_SBB(x) (((x) & 0x7) << 8) +#define NFC_V3_CONFIG3_NUM_OF_DEVICES(x) (((x) & 0x7) << 12) +#define NFC_V3_CONFIG3_RBB_MODE (1 << 15) +#define NFC_V3_CONFIG3_NO_SDMA (1 << 20) + +#define NFC_V3_IPC (host->regs_ip + 0x2C) +#define NFC_V3_IPC_CREQ (1 << 0) +#define NFC_V3_IPC_INT (1 << 31) + +#define NFC_V3_DELAY_LINE (host->regs_ip + 0x34) + +struct mxc_nand_host; + +struct mxc_nand_devtype_data { + void (*preset)(struct mtd_info *); + void (*send_cmd)(struct mxc_nand_host *, uint16_t, int); + void (*send_addr)(struct mxc_nand_host *, uint16_t, int); + void (*send_page)(struct mtd_info *, unsigned int); + void (*send_read_id)(struct mxc_nand_host *); + uint16_t (*get_dev_status)(struct mxc_nand_host *); + int (*check_int)(struct mxc_nand_host *); + void (*irq_control)(struct mxc_nand_host *, int); + u32 (*get_ecc_status)(struct mxc_nand_host *); + struct nand_ecclayout *ecclayout_512, *ecclayout_2k, *ecclayout_4k; + void (*select_chip)(struct mtd_info *mtd, int chip); + int (*correct_data)(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc); + + /* + * On i.MX21 the CONFIG2:INT bit cannot be read if interrupts are masked + * (CONFIG1:INT_MSK is set). To handle this the driver uses + * enable_irq/disable_irq_nosync instead of CONFIG1:INT_MSK + */ + int irqpending_quirk; + int needs_ip; + + size_t regs_offset; + size_t spare0_offset; + size_t axi_offset; + + int spare_len; + int eccbytes; + int eccsize; + int ppb_shift; +}; + +struct mxc_nand_host { + struct mtd_info mtd; + struct nand_chip nand; + struct device *dev; + + void __iomem *spare0; + void __iomem *main_area0; + + void __iomem *base; + void __iomem *regs; + void __iomem *regs_axi; + void __iomem *regs_ip; + int status_request; + struct clk *clk; + int clk_act; + int irq; + int eccsize; + int active_cs; + + struct completion op_completion; + + uint8_t *data_buf; + unsigned int buf_start; + + const struct mxc_nand_devtype_data *devtype_data; + struct mxc_nand_platform_data pdata; +}; + +/* OOB placement block for use with hardware ecc generation */ +static struct nand_ecclayout nandv1_hw_eccoob_smallpage = { + .eccbytes = 5, + .eccpos = {6, 7, 8, 9, 10}, + .oobfree = {{0, 5}, {12, 4}, } +}; + +static struct nand_ecclayout nandv1_hw_eccoob_largepage = { + .eccbytes = 20, + .eccpos = {6, 7, 8, 9, 10, 22, 23, 24, 25, 26, + 38, 39, 40, 41, 42, 54, 55, 56, 57, 58}, + .oobfree = {{2, 4}, {11, 10}, {27, 10}, {43, 10}, {59, 5}, } +}; + +/* OOB description for 512 byte pages with 16 byte OOB */ +static struct nand_ecclayout nandv2_hw_eccoob_smallpage = { + .eccbytes = 1 * 9, + .eccpos = { + 7, 8, 9, 10, 11, 12, 13, 14, 15 + }, + .oobfree = { + {.offset = 0, .length = 5} + } +}; + +/* OOB description for 2048 byte pages with 64 byte OOB */ +static struct nand_ecclayout nandv2_hw_eccoob_largepage = { + .eccbytes = 4 * 9, + .eccpos = { + 7, 8, 9, 10, 11, 12, 13, 14, 15, + 23, 24, 25, 26, 27, 28, 29, 30, 31, + 39, 40, 41, 42, 43, 44, 45, 46, 47, + 55, 56, 57, 58, 59, 60, 61, 62, 63 + }, + .oobfree = { + {.offset = 2, .length = 4}, + {.offset = 16, .length = 7}, + {.offset = 32, .length = 7}, + {.offset = 48, .length = 7} + } +}; + +/* OOB description for 4096 byte pages with 128 byte OOB */ +static struct nand_ecclayout nandv2_hw_eccoob_4k = { + .eccbytes = 8 * 9, + .eccpos = { + 7, 8, 9, 10, 11, 12, 13, 14, 15, + 23, 24, 25, 26, 27, 28, 29, 30, 31, + 39, 40, 41, 42, 43, 44, 45, 46, 47, + 55, 56, 57, 58, 59, 60, 61, 62, 63, + 71, 72, 73, 74, 75, 76, 77, 78, 79, + 87, 88, 89, 90, 91, 92, 93, 94, 95, + 103, 104, 105, 106, 107, 108, 109, 110, 111, + 119, 120, 121, 122, 123, 124, 125, 126, 127, + }, + .oobfree = { + {.offset = 2, .length = 4}, + {.offset = 16, .length = 7}, + {.offset = 32, .length = 7}, + {.offset = 48, .length = 7}, + {.offset = 64, .length = 7}, + {.offset = 80, .length = 7}, + {.offset = 96, .length = 7}, + {.offset = 112, .length = 7}, + } +}; + +static const char * const part_probes[] = { + "cmdlinepart", "RedBoot", "ofpart", NULL }; + +static void memcpy32_fromio(void *trg, const void __iomem *src, size_t size) +{ + int i; + u32 *t = trg; + const __iomem u32 *s = src; + + for (i = 0; i < (size >> 2); i++) + *t++ = __raw_readl(s++); +} + +static inline void memcpy32_toio(void __iomem *trg, const void *src, int size) +{ + /* __iowrite32_copy use 32bit size values so divide by 4 */ + __iowrite32_copy(trg, src, size / 4); +} + +static int check_int_v3(struct mxc_nand_host *host) +{ + uint32_t tmp; + + tmp = readl(NFC_V3_IPC); + if (!(tmp & NFC_V3_IPC_INT)) + return 0; + + tmp &= ~NFC_V3_IPC_INT; + writel(tmp, NFC_V3_IPC); + + return 1; +} + +static int check_int_v1_v2(struct mxc_nand_host *host) +{ + uint32_t tmp; + + tmp = readw(NFC_V1_V2_CONFIG2); + if (!(tmp & NFC_V1_V2_CONFIG2_INT)) + return 0; + + if (!host->devtype_data->irqpending_quirk) + writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2); + + return 1; +} + +static void irq_control_v1_v2(struct mxc_nand_host *host, int activate) +{ + uint16_t tmp; + + tmp = readw(NFC_V1_V2_CONFIG1); + + if (activate) + tmp &= ~NFC_V1_V2_CONFIG1_INT_MSK; + else + tmp |= NFC_V1_V2_CONFIG1_INT_MSK; + + writew(tmp, NFC_V1_V2_CONFIG1); +} + +static void irq_control_v3(struct mxc_nand_host *host, int activate) +{ + uint32_t tmp; + + tmp = readl(NFC_V3_CONFIG2); + + if (activate) + tmp &= ~NFC_V3_CONFIG2_INT_MSK; + else + tmp |= NFC_V3_CONFIG2_INT_MSK; + + writel(tmp, NFC_V3_CONFIG2); +} + +static void irq_control(struct mxc_nand_host *host, int activate) +{ + if (host->devtype_data->irqpending_quirk) { + if (activate) + enable_irq(host->irq); + else + disable_irq_nosync(host->irq); + } else { + host->devtype_data->irq_control(host, activate); + } +} + +static u32 get_ecc_status_v1(struct mxc_nand_host *host) +{ + return readw(NFC_V1_V2_ECC_STATUS_RESULT); +} + +static u32 get_ecc_status_v2(struct mxc_nand_host *host) +{ + return readl(NFC_V1_V2_ECC_STATUS_RESULT); +} + +static u32 get_ecc_status_v3(struct mxc_nand_host *host) +{ + return readl(NFC_V3_ECC_STATUS_RESULT); +} + +static irqreturn_t mxc_nfc_irq(int irq, void *dev_id) +{ + struct mxc_nand_host *host = dev_id; + + if (!host->devtype_data->check_int(host)) + return IRQ_NONE; + + irq_control(host, 0); + + complete(&host->op_completion); + + return IRQ_HANDLED; +} + +/* This function polls the NANDFC to wait for the basic operation to + * complete by checking the INT bit of config2 register. + */ +static int wait_op_done(struct mxc_nand_host *host, int useirq) +{ + int ret = 0; + + /* + * If operation is already complete, don't bother to setup an irq or a + * loop. + */ + if (host->devtype_data->check_int(host)) + return 0; + + if (useirq) { + unsigned long timeout; + + reinit_completion(&host->op_completion); + + irq_control(host, 1); + + timeout = wait_for_completion_timeout(&host->op_completion, HZ); + if (!timeout && !host->devtype_data->check_int(host)) { + dev_dbg(host->dev, "timeout waiting for irq\n"); + ret = -ETIMEDOUT; + } + } else { + int max_retries = 8000; + int done; + + do { + udelay(1); + + done = host->devtype_data->check_int(host); + if (done) + break; + + } while (--max_retries); + + if (!done) { + dev_dbg(host->dev, "timeout polling for completion\n"); + ret = -ETIMEDOUT; + } + } + + WARN_ONCE(ret < 0, "timeout! useirq=%d\n", useirq); + + return ret; +} + +static void send_cmd_v3(struct mxc_nand_host *host, uint16_t cmd, int useirq) +{ + /* fill command */ + writel(cmd, NFC_V3_FLASH_CMD); + + /* send out command */ + writel(NFC_CMD, NFC_V3_LAUNCH); + + /* Wait for operation to complete */ + wait_op_done(host, useirq); +} + +/* This function issues the specified command to the NAND device and + * waits for completion. */ +static void send_cmd_v1_v2(struct mxc_nand_host *host, uint16_t cmd, int useirq) +{ + pr_debug("send_cmd(host, 0x%x, %d)\n", cmd, useirq); + + writew(cmd, NFC_V1_V2_FLASH_CMD); + writew(NFC_CMD, NFC_V1_V2_CONFIG2); + + if (host->devtype_data->irqpending_quirk && (cmd == NAND_CMD_RESET)) { + int max_retries = 100; + /* Reset completion is indicated by NFC_CONFIG2 */ + /* being set to 0 */ + while (max_retries-- > 0) { + if (readw(NFC_V1_V2_CONFIG2) == 0) { + break; + } + udelay(1); + } + if (max_retries < 0) + pr_debug("%s: RESET failed\n", __func__); + } else { + /* Wait for operation to complete */ + wait_op_done(host, useirq); + } +} + +static void send_addr_v3(struct mxc_nand_host *host, uint16_t addr, int islast) +{ + /* fill address */ + writel(addr, NFC_V3_FLASH_ADDR0); + + /* send out address */ + writel(NFC_ADDR, NFC_V3_LAUNCH); + + wait_op_done(host, 0); +} + +/* This function sends an address (or partial address) to the + * NAND device. The address is used to select the source/destination for + * a NAND command. */ +static void send_addr_v1_v2(struct mxc_nand_host *host, uint16_t addr, int islast) +{ + pr_debug("send_addr(host, 0x%x %d)\n", addr, islast); + + writew(addr, NFC_V1_V2_FLASH_ADDR); + writew(NFC_ADDR, NFC_V1_V2_CONFIG2); + + /* Wait for operation to complete */ + wait_op_done(host, islast); +} + +static void send_page_v3(struct mtd_info *mtd, unsigned int ops) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + uint32_t tmp; + + tmp = readl(NFC_V3_CONFIG1); + tmp &= ~(7 << 4); + writel(tmp, NFC_V3_CONFIG1); + + /* transfer data from NFC ram to nand */ + writel(ops, NFC_V3_LAUNCH); + + wait_op_done(host, false); +} + +static void send_page_v2(struct mtd_info *mtd, unsigned int ops) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + /* NANDFC buffer 0 is used for page read/write */ + writew(host->active_cs << 4, NFC_V1_V2_BUF_ADDR); + + writew(ops, NFC_V1_V2_CONFIG2); + + /* Wait for operation to complete */ + wait_op_done(host, true); +} + +static void send_page_v1(struct mtd_info *mtd, unsigned int ops) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + int bufs, i; + + if (mtd->writesize > 512) + bufs = 4; + else + bufs = 1; + + for (i = 0; i < bufs; i++) { + + /* NANDFC buffer 0 is used for page read/write */ + writew((host->active_cs << 4) | i, NFC_V1_V2_BUF_ADDR); + + writew(ops, NFC_V1_V2_CONFIG2); + + /* Wait for operation to complete */ + wait_op_done(host, true); + } +} + +static void send_read_id_v3(struct mxc_nand_host *host) +{ + /* Read ID into main buffer */ + writel(NFC_ID, NFC_V3_LAUNCH); + + wait_op_done(host, true); + + memcpy32_fromio(host->data_buf, host->main_area0, 16); +} + +/* Request the NANDFC to perform a read of the NAND device ID. */ +static void send_read_id_v1_v2(struct mxc_nand_host *host) +{ + /* NANDFC buffer 0 is used for device ID output */ + writew(host->active_cs << 4, NFC_V1_V2_BUF_ADDR); + + writew(NFC_ID, NFC_V1_V2_CONFIG2); + + /* Wait for operation to complete */ + wait_op_done(host, true); + + memcpy32_fromio(host->data_buf, host->main_area0, 16); +} + +static uint16_t get_dev_status_v3(struct mxc_nand_host *host) +{ + writew(NFC_STATUS, NFC_V3_LAUNCH); + wait_op_done(host, true); + + return readl(NFC_V3_CONFIG1) >> 16; +} + +/* This function requests the NANDFC to perform a read of the + * NAND device status and returns the current status. */ +static uint16_t get_dev_status_v1_v2(struct mxc_nand_host *host) +{ + void __iomem *main_buf = host->main_area0; + uint32_t store; + uint16_t ret; + + writew(host->active_cs << 4, NFC_V1_V2_BUF_ADDR); + + /* + * The device status is stored in main_area0. To + * prevent corruption of the buffer save the value + * and restore it afterwards. + */ + store = readl(main_buf); + + writew(NFC_STATUS, NFC_V1_V2_CONFIG2); + wait_op_done(host, true); + + ret = readw(main_buf); + + writel(store, main_buf); + + return ret; +} + +/* This functions is used by upper layer to checks if device is ready */ +static int mxc_nand_dev_ready(struct mtd_info *mtd) +{ + /* + * NFC handles R/B internally. Therefore, this function + * always returns status as ready. + */ + return 1; +} + +static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + /* + * If HW ECC is enabled, we turn it on during init. There is + * no need to enable again here. + */ +} + +static int mxc_nand_correct_data_v1(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + /* + * 1-Bit errors are automatically corrected in HW. No need for + * additional correction. 2-Bit errors cannot be corrected by + * HW ECC, so we need to return failure + */ + uint16_t ecc_status = get_ecc_status_v1(host); + + if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) { + pr_debug("MXC_NAND: HWECC uncorrectable 2-bit ECC error\n"); + return -1; + } + + return 0; +} + +static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + u32 ecc_stat, err; + int no_subpages = 1; + int ret = 0; + u8 ecc_bit_mask, err_limit; + + ecc_bit_mask = (host->eccsize == 4) ? 0x7 : 0xf; + err_limit = (host->eccsize == 4) ? 0x4 : 0x8; + + no_subpages = mtd->writesize >> 9; + + ecc_stat = host->devtype_data->get_ecc_status(host); + + do { + err = ecc_stat & ecc_bit_mask; + if (err > err_limit) { + printk(KERN_WARNING "UnCorrectable RS-ECC Error\n"); + return -1; + } else { + ret += err; + } + ecc_stat >>= 4; + } while (--no_subpages); + + pr_debug("%d Symbol Correctable RS-ECC Error\n", ret); + + return ret; +} + +static int mxc_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + return 0; +} + +static u_char mxc_nand_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + uint8_t ret; + + /* Check for status request */ + if (host->status_request) + return host->devtype_data->get_dev_status(host) & 0xFF; + + if (nand_chip->options & NAND_BUSWIDTH_16) { + /* only take the lower byte of each word */ + ret = *(uint16_t *)(host->data_buf + host->buf_start); + + host->buf_start += 2; + } else { + ret = *(uint8_t *)(host->data_buf + host->buf_start); + host->buf_start++; + } + + pr_debug("%s: ret=0x%hhx (start=%u)\n", __func__, ret, host->buf_start); + return ret; +} + +static uint16_t mxc_nand_read_word(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + uint16_t ret; + + ret = *(uint16_t *)(host->data_buf + host->buf_start); + host->buf_start += 2; + + return ret; +} + +/* Write data of length len to buffer buf. The data to be + * written on NAND Flash is first copied to RAMbuffer. After the Data Input + * Operation by the NFC, the data is written to NAND Flash */ +static void mxc_nand_write_buf(struct mtd_info *mtd, + const u_char *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + u16 col = host->buf_start; + int n = mtd->oobsize + mtd->writesize - col; + + n = min(n, len); + + memcpy(host->data_buf + col, buf, n); + + host->buf_start += n; +} + +/* Read the data buffer from the NAND Flash. To read the data from NAND + * Flash first the data output cycle is initiated by the NFC, which copies + * the data to RAMbuffer. This data of length len is then copied to buffer buf. + */ +static void mxc_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + u16 col = host->buf_start; + int n = mtd->oobsize + mtd->writesize - col; + + n = min(n, len); + + memcpy(buf, host->data_buf + col, n); + + host->buf_start += n; +} + +/* This function is used by upper layer for select and + * deselect of the NAND chip */ +static void mxc_nand_select_chip_v1_v3(struct mtd_info *mtd, int chip) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + if (chip == -1) { + /* Disable the NFC clock */ + if (host->clk_act) { + clk_disable_unprepare(host->clk); + host->clk_act = 0; + } + return; + } + + if (!host->clk_act) { + /* Enable the NFC clock */ + clk_prepare_enable(host->clk); + host->clk_act = 1; + } +} + +static void mxc_nand_select_chip_v2(struct mtd_info *mtd, int chip) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + if (chip == -1) { + /* Disable the NFC clock */ + if (host->clk_act) { + clk_disable_unprepare(host->clk); + host->clk_act = 0; + } + return; + } + + if (!host->clk_act) { + /* Enable the NFC clock */ + clk_prepare_enable(host->clk); + host->clk_act = 1; + } + + host->active_cs = chip; + writew(host->active_cs << 4, NFC_V1_V2_BUF_ADDR); +} + +/* + * Function to transfer data to/from spare area. + */ +static void copy_spare(struct mtd_info *mtd, bool bfrom) +{ + struct nand_chip *this = mtd->priv; + struct mxc_nand_host *host = this->priv; + u16 i, j; + u16 n = mtd->writesize >> 9; + u8 *d = host->data_buf + mtd->writesize; + u8 __iomem *s = host->spare0; + u16 t = host->devtype_data->spare_len; + + j = (mtd->oobsize / n >> 1) << 1; + + if (bfrom) { + for (i = 0; i < n - 1; i++) + memcpy32_fromio(d + i * j, s + i * t, j); + + /* the last section */ + memcpy32_fromio(d + i * j, s + i * t, mtd->oobsize - i * j); + } else { + for (i = 0; i < n - 1; i++) + memcpy32_toio(&s[i * t], &d[i * j], j); + + /* the last section */ + memcpy32_toio(&s[i * t], &d[i * j], mtd->oobsize - i * j); + } +} + +/* + * MXC NANDFC can only perform full page+spare or spare-only read/write. When + * the upper layers perform a read/write buf operation, the saved column address + * is used to index into the full page. So usually this function is called with + * column == 0 (unless no column cycle is needed indicated by column == -1) + */ +static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + /* Write out column address, if necessary */ + if (column != -1) { + host->devtype_data->send_addr(host, column & 0xff, + page_addr == -1); + if (mtd->writesize > 512) + /* another col addr cycle for 2k page */ + host->devtype_data->send_addr(host, + (column >> 8) & 0xff, + false); + } + + /* Write out page address, if necessary */ + if (page_addr != -1) { + /* paddr_0 - p_addr_7 */ + host->devtype_data->send_addr(host, (page_addr & 0xff), false); + + if (mtd->writesize > 512) { + if (mtd->size >= 0x10000000) { + /* paddr_8 - paddr_15 */ + host->devtype_data->send_addr(host, + (page_addr >> 8) & 0xff, + false); + host->devtype_data->send_addr(host, + (page_addr >> 16) & 0xff, + true); + } else + /* paddr_8 - paddr_15 */ + host->devtype_data->send_addr(host, + (page_addr >> 8) & 0xff, true); + } else { + /* One more address cycle for higher density devices */ + if (mtd->size >= 0x4000000) { + /* paddr_8 - paddr_15 */ + host->devtype_data->send_addr(host, + (page_addr >> 8) & 0xff, + false); + host->devtype_data->send_addr(host, + (page_addr >> 16) & 0xff, + true); + } else + /* paddr_8 - paddr_15 */ + host->devtype_data->send_addr(host, + (page_addr >> 8) & 0xff, true); + } + } +} + +/* + * v2 and v3 type controllers can do 4bit or 8bit ecc depending + * on how much oob the nand chip has. For 8bit ecc we need at least + * 26 bytes of oob data per 512 byte block. + */ +static int get_eccsize(struct mtd_info *mtd) +{ + int oobbytes_per_512 = 0; + + oobbytes_per_512 = mtd->oobsize * 512 / mtd->writesize; + + if (oobbytes_per_512 < 26) + return 4; + else + return 8; +} + +static void preset_v1(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + uint16_t config1 = 0; + + if (nand_chip->ecc.mode == NAND_ECC_HW && mtd->writesize) + config1 |= NFC_V1_V2_CONFIG1_ECC_EN; + + if (!host->devtype_data->irqpending_quirk) + config1 |= NFC_V1_V2_CONFIG1_INT_MSK; + + host->eccsize = 1; + + writew(config1, NFC_V1_V2_CONFIG1); + /* preset operation */ + + /* Unlock the internal RAM Buffer */ + writew(0x2, NFC_V1_V2_CONFIG); + + /* Blocks to be unlocked */ + writew(0x0, NFC_V1_UNLOCKSTART_BLKADDR); + writew(0xffff, NFC_V1_UNLOCKEND_BLKADDR); + + /* Unlock Block Command for given address range */ + writew(0x4, NFC_V1_V2_WRPROT); +} + +static void preset_v2(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + uint16_t config1 = 0; + + config1 |= NFC_V2_CONFIG1_FP_INT; + + if (!host->devtype_data->irqpending_quirk) + config1 |= NFC_V1_V2_CONFIG1_INT_MSK; + + if (mtd->writesize) { + uint16_t pages_per_block = mtd->erasesize / mtd->writesize; + + if (nand_chip->ecc.mode == NAND_ECC_HW) + config1 |= NFC_V1_V2_CONFIG1_ECC_EN; + + host->eccsize = get_eccsize(mtd); + if (host->eccsize == 4) + config1 |= NFC_V2_CONFIG1_ECC_MODE_4; + + config1 |= NFC_V2_CONFIG1_PPB(ffs(pages_per_block) - 6); + } else { + host->eccsize = 1; + } + + writew(config1, NFC_V1_V2_CONFIG1); + /* preset operation */ + + /* Unlock the internal RAM Buffer */ + writew(0x2, NFC_V1_V2_CONFIG); + + /* Blocks to be unlocked */ + writew(0x0, NFC_V21_UNLOCKSTART_BLKADDR0); + writew(0x0, NFC_V21_UNLOCKSTART_BLKADDR1); + writew(0x0, NFC_V21_UNLOCKSTART_BLKADDR2); + writew(0x0, NFC_V21_UNLOCKSTART_BLKADDR3); + writew(0xffff, NFC_V21_UNLOCKEND_BLKADDR0); + writew(0xffff, NFC_V21_UNLOCKEND_BLKADDR1); + writew(0xffff, NFC_V21_UNLOCKEND_BLKADDR2); + writew(0xffff, NFC_V21_UNLOCKEND_BLKADDR3); + + /* Unlock Block Command for given address range */ + writew(0x4, NFC_V1_V2_WRPROT); +} + +static void preset_v3(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct mxc_nand_host *host = chip->priv; + uint32_t config2, config3; + int i, addr_phases; + + writel(NFC_V3_CONFIG1_RBA(0), NFC_V3_CONFIG1); + writel(NFC_V3_IPC_CREQ, NFC_V3_IPC); + + /* Unlock the internal RAM Buffer */ + writel(NFC_V3_WRPROT_BLS_UNLOCK | NFC_V3_WRPROT_UNLOCK, + NFC_V3_WRPROT); + + /* Blocks to be unlocked */ + for (i = 0; i < NAND_MAX_CHIPS; i++) + writel(0x0 | (0xffff << 16), + NFC_V3_WRPROT_UNLOCK_BLK_ADD0 + (i << 2)); + + writel(0, NFC_V3_IPC); + + config2 = NFC_V3_CONFIG2_ONE_CYCLE | + NFC_V3_CONFIG2_2CMD_PHASES | + NFC_V3_CONFIG2_SPAS(mtd->oobsize >> 1) | + NFC_V3_CONFIG2_ST_CMD(0x70) | + NFC_V3_CONFIG2_INT_MSK | + NFC_V3_CONFIG2_NUM_ADDR_PHASE0; + + addr_phases = fls(chip->pagemask) >> 3; + + if (mtd->writesize == 2048) { + config2 |= NFC_V3_CONFIG2_PS_2048; + config2 |= NFC_V3_CONFIG2_NUM_ADDR_PHASE1(addr_phases); + } else if (mtd->writesize == 4096) { + config2 |= NFC_V3_CONFIG2_PS_4096; + config2 |= NFC_V3_CONFIG2_NUM_ADDR_PHASE1(addr_phases); + } else { + config2 |= NFC_V3_CONFIG2_PS_512; + config2 |= NFC_V3_CONFIG2_NUM_ADDR_PHASE1(addr_phases - 1); + } + + if (mtd->writesize) { + if (chip->ecc.mode == NAND_ECC_HW) + config2 |= NFC_V3_CONFIG2_ECC_EN; + + config2 |= NFC_V3_CONFIG2_PPB( + ffs(mtd->erasesize / mtd->writesize) - 6, + host->devtype_data->ppb_shift); + host->eccsize = get_eccsize(mtd); + if (host->eccsize == 8) + config2 |= NFC_V3_CONFIG2_ECC_MODE_8; + } + + writel(config2, NFC_V3_CONFIG2); + + config3 = NFC_V3_CONFIG3_NUM_OF_DEVICES(0) | + NFC_V3_CONFIG3_NO_SDMA | + NFC_V3_CONFIG3_RBB_MODE | + NFC_V3_CONFIG3_SBB(6) | /* Reset default */ + NFC_V3_CONFIG3_ADD_OP(0); + + if (!(chip->options & NAND_BUSWIDTH_16)) + config3 |= NFC_V3_CONFIG3_FW8; + + writel(config3, NFC_V3_CONFIG3); + + writel(0, NFC_V3_DELAY_LINE); +} + +/* Used by the upper layer to write command to NAND Flash for + * different operations to be carried out on NAND Flash */ +static void mxc_nand_command(struct mtd_info *mtd, unsigned command, + int column, int page_addr) +{ + struct nand_chip *nand_chip = mtd->priv; + struct mxc_nand_host *host = nand_chip->priv; + + pr_debug("mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n", + command, column, page_addr); + + /* Reset command state information */ + host->status_request = false; + + /* Command pre-processing step */ + switch (command) { + case NAND_CMD_RESET: + host->devtype_data->preset(mtd); + host->devtype_data->send_cmd(host, command, false); + break; + + case NAND_CMD_STATUS: + host->buf_start = 0; + host->status_request = true; + + host->devtype_data->send_cmd(host, command, true); + WARN_ONCE(column != -1 || page_addr != -1, + "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n", + command, column, page_addr); + mxc_do_addr_cycle(mtd, column, page_addr); + break; + + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + if (command == NAND_CMD_READ0) + host->buf_start = column; + else + host->buf_start = column + mtd->writesize; + + command = NAND_CMD_READ0; /* only READ0 is valid */ + + host->devtype_data->send_cmd(host, command, false); + WARN_ONCE(column < 0, + "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n", + command, column, page_addr); + mxc_do_addr_cycle(mtd, 0, page_addr); + + if (mtd->writesize > 512) + host->devtype_data->send_cmd(host, + NAND_CMD_READSTART, true); + + host->devtype_data->send_page(mtd, NFC_OUTPUT); + + memcpy32_fromio(host->data_buf, host->main_area0, + mtd->writesize); + copy_spare(mtd, true); + break; + + case NAND_CMD_SEQIN: + if (column >= mtd->writesize) + /* call ourself to read a page */ + mxc_nand_command(mtd, NAND_CMD_READ0, 0, page_addr); + + host->buf_start = column; + + host->devtype_data->send_cmd(host, command, false); + WARN_ONCE(column < -1, + "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n", + command, column, page_addr); + mxc_do_addr_cycle(mtd, 0, page_addr); + break; + + case NAND_CMD_PAGEPROG: + memcpy32_toio(host->main_area0, host->data_buf, mtd->writesize); + copy_spare(mtd, false); + host->devtype_data->send_page(mtd, NFC_INPUT); + host->devtype_data->send_cmd(host, command, true); + WARN_ONCE(column != -1 || page_addr != -1, + "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n", + command, column, page_addr); + mxc_do_addr_cycle(mtd, column, page_addr); + break; + + case NAND_CMD_READID: + host->devtype_data->send_cmd(host, command, true); + mxc_do_addr_cycle(mtd, column, page_addr); + host->devtype_data->send_read_id(host); + host->buf_start = 0; + break; + + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + host->devtype_data->send_cmd(host, command, false); + WARN_ONCE(column != -1, + "Unexpected column value (cmd=%u, col=%d)\n", + command, column); + mxc_do_addr_cycle(mtd, column, page_addr); + + break; + case NAND_CMD_PARAM: + host->devtype_data->send_cmd(host, command, false); + mxc_do_addr_cycle(mtd, column, page_addr); + host->devtype_data->send_page(mtd, NFC_OUTPUT); + memcpy32_fromio(host->data_buf, host->main_area0, 512); + host->buf_start = 0; + break; + default: + WARN_ONCE(1, "Unimplemented command (cmd=%u)\n", + command); + break; + } +} + +/* + * The generic flash bbt decriptors overlap with our ecc + * hardware, so define some i.MX specific ones. + */ +static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' }; +static uint8_t mirror_pattern[] = { '1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 0, + .len = 4, + .veroffs = 4, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 0, + .len = 4, + .veroffs = 4, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/* v1 + irqpending_quirk: i.MX21 */ +static const struct mxc_nand_devtype_data imx21_nand_devtype_data = { + .preset = preset_v1, + .send_cmd = send_cmd_v1_v2, + .send_addr = send_addr_v1_v2, + .send_page = send_page_v1, + .send_read_id = send_read_id_v1_v2, + .get_dev_status = get_dev_status_v1_v2, + .check_int = check_int_v1_v2, + .irq_control = irq_control_v1_v2, + .get_ecc_status = get_ecc_status_v1, + .ecclayout_512 = &nandv1_hw_eccoob_smallpage, + .ecclayout_2k = &nandv1_hw_eccoob_largepage, + .ecclayout_4k = &nandv1_hw_eccoob_smallpage, /* XXX: needs fix */ + .select_chip = mxc_nand_select_chip_v1_v3, + .correct_data = mxc_nand_correct_data_v1, + .irqpending_quirk = 1, + .needs_ip = 0, + .regs_offset = 0xe00, + .spare0_offset = 0x800, + .spare_len = 16, + .eccbytes = 3, + .eccsize = 1, +}; + +/* v1 + !irqpending_quirk: i.MX27, i.MX31 */ +static const struct mxc_nand_devtype_data imx27_nand_devtype_data = { + .preset = preset_v1, + .send_cmd = send_cmd_v1_v2, + .send_addr = send_addr_v1_v2, + .send_page = send_page_v1, + .send_read_id = send_read_id_v1_v2, + .get_dev_status = get_dev_status_v1_v2, + .check_int = check_int_v1_v2, + .irq_control = irq_control_v1_v2, + .get_ecc_status = get_ecc_status_v1, + .ecclayout_512 = &nandv1_hw_eccoob_smallpage, + .ecclayout_2k = &nandv1_hw_eccoob_largepage, + .ecclayout_4k = &nandv1_hw_eccoob_smallpage, /* XXX: needs fix */ + .select_chip = mxc_nand_select_chip_v1_v3, + .correct_data = mxc_nand_correct_data_v1, + .irqpending_quirk = 0, + .needs_ip = 0, + .regs_offset = 0xe00, + .spare0_offset = 0x800, + .axi_offset = 0, + .spare_len = 16, + .eccbytes = 3, + .eccsize = 1, +}; + +/* v21: i.MX25, i.MX35 */ +static const struct mxc_nand_devtype_data imx25_nand_devtype_data = { + .preset = preset_v2, + .send_cmd = send_cmd_v1_v2, + .send_addr = send_addr_v1_v2, + .send_page = send_page_v2, + .send_read_id = send_read_id_v1_v2, + .get_dev_status = get_dev_status_v1_v2, + .check_int = check_int_v1_v2, + .irq_control = irq_control_v1_v2, + .get_ecc_status = get_ecc_status_v2, + .ecclayout_512 = &nandv2_hw_eccoob_smallpage, + .ecclayout_2k = &nandv2_hw_eccoob_largepage, + .ecclayout_4k = &nandv2_hw_eccoob_4k, + .select_chip = mxc_nand_select_chip_v2, + .correct_data = mxc_nand_correct_data_v2_v3, + .irqpending_quirk = 0, + .needs_ip = 0, + .regs_offset = 0x1e00, + .spare0_offset = 0x1000, + .axi_offset = 0, + .spare_len = 64, + .eccbytes = 9, + .eccsize = 0, +}; + +/* v3.2a: i.MX51 */ +static const struct mxc_nand_devtype_data imx51_nand_devtype_data = { + .preset = preset_v3, + .send_cmd = send_cmd_v3, + .send_addr = send_addr_v3, + .send_page = send_page_v3, + .send_read_id = send_read_id_v3, + .get_dev_status = get_dev_status_v3, + .check_int = check_int_v3, + .irq_control = irq_control_v3, + .get_ecc_status = get_ecc_status_v3, + .ecclayout_512 = &nandv2_hw_eccoob_smallpage, + .ecclayout_2k = &nandv2_hw_eccoob_largepage, + .ecclayout_4k = &nandv2_hw_eccoob_smallpage, /* XXX: needs fix */ + .select_chip = mxc_nand_select_chip_v1_v3, + .correct_data = mxc_nand_correct_data_v2_v3, + .irqpending_quirk = 0, + .needs_ip = 1, + .regs_offset = 0, + .spare0_offset = 0x1000, + .axi_offset = 0x1e00, + .spare_len = 64, + .eccbytes = 0, + .eccsize = 0, + .ppb_shift = 7, +}; + +/* v3.2b: i.MX53 */ +static const struct mxc_nand_devtype_data imx53_nand_devtype_data = { + .preset = preset_v3, + .send_cmd = send_cmd_v3, + .send_addr = send_addr_v3, + .send_page = send_page_v3, + .send_read_id = send_read_id_v3, + .get_dev_status = get_dev_status_v3, + .check_int = check_int_v3, + .irq_control = irq_control_v3, + .get_ecc_status = get_ecc_status_v3, + .ecclayout_512 = &nandv2_hw_eccoob_smallpage, + .ecclayout_2k = &nandv2_hw_eccoob_largepage, + .ecclayout_4k = &nandv2_hw_eccoob_smallpage, /* XXX: needs fix */ + .select_chip = mxc_nand_select_chip_v1_v3, + .correct_data = mxc_nand_correct_data_v2_v3, + .irqpending_quirk = 0, + .needs_ip = 1, + .regs_offset = 0, + .spare0_offset = 0x1000, + .axi_offset = 0x1e00, + .spare_len = 64, + .eccbytes = 0, + .eccsize = 0, + .ppb_shift = 8, +}; + +static inline int is_imx21_nfc(struct mxc_nand_host *host) +{ + return host->devtype_data == &imx21_nand_devtype_data; +} + +static inline int is_imx27_nfc(struct mxc_nand_host *host) +{ + return host->devtype_data == &imx27_nand_devtype_data; +} + +static inline int is_imx25_nfc(struct mxc_nand_host *host) +{ + return host->devtype_data == &imx25_nand_devtype_data; +} + +static inline int is_imx51_nfc(struct mxc_nand_host *host) +{ + return host->devtype_data == &imx51_nand_devtype_data; +} + +static inline int is_imx53_nfc(struct mxc_nand_host *host) +{ + return host->devtype_data == &imx53_nand_devtype_data; +} + +static struct platform_device_id mxcnd_devtype[] = { + { + .name = "imx21-nand", + .driver_data = (kernel_ulong_t) &imx21_nand_devtype_data, + }, { + .name = "imx27-nand", + .driver_data = (kernel_ulong_t) &imx27_nand_devtype_data, + }, { + .name = "imx25-nand", + .driver_data = (kernel_ulong_t) &imx25_nand_devtype_data, + }, { + .name = "imx51-nand", + .driver_data = (kernel_ulong_t) &imx51_nand_devtype_data, + }, { + .name = "imx53-nand", + .driver_data = (kernel_ulong_t) &imx53_nand_devtype_data, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(platform, mxcnd_devtype); + +#ifdef CONFIG_OF_MTD +static const struct of_device_id mxcnd_dt_ids[] = { + { + .compatible = "fsl,imx21-nand", + .data = &imx21_nand_devtype_data, + }, { + .compatible = "fsl,imx27-nand", + .data = &imx27_nand_devtype_data, + }, { + .compatible = "fsl,imx25-nand", + .data = &imx25_nand_devtype_data, + }, { + .compatible = "fsl,imx51-nand", + .data = &imx51_nand_devtype_data, + }, { + .compatible = "fsl,imx53-nand", + .data = &imx53_nand_devtype_data, + }, + { /* sentinel */ } +}; + +static int __init mxcnd_probe_dt(struct mxc_nand_host *host) +{ + struct device_node *np = host->dev->of_node; + struct mxc_nand_platform_data *pdata = &host->pdata; + const struct of_device_id *of_id = + of_match_device(mxcnd_dt_ids, host->dev); + int buswidth; + + if (!np) + return 1; + + if (of_get_nand_ecc_mode(np) >= 0) + pdata->hw_ecc = 1; + + pdata->flash_bbt = of_get_nand_on_flash_bbt(np); + + buswidth = of_get_nand_bus_width(np); + if (buswidth < 0) + return buswidth; + + pdata->width = buswidth / 8; + + host->devtype_data = of_id->data; + + return 0; +} +#else +static int __init mxcnd_probe_dt(struct mxc_nand_host *host) +{ + return 1; +} +#endif + +static int mxcnd_probe(struct platform_device *pdev) +{ + struct nand_chip *this; + struct mtd_info *mtd; + struct mxc_nand_host *host; + struct resource *res; + int err = 0; + + /* Allocate memory for MTD device structure and private data */ + host = devm_kzalloc(&pdev->dev, sizeof(struct mxc_nand_host), + GFP_KERNEL); + if (!host) + return -ENOMEM; + + /* allocate a temporary buffer for the nand_scan_ident() */ + host->data_buf = devm_kzalloc(&pdev->dev, PAGE_SIZE, GFP_KERNEL); + if (!host->data_buf) + return -ENOMEM; + + host->dev = &pdev->dev; + /* structures must be linked */ + this = &host->nand; + mtd = &host->mtd; + mtd->priv = this; + mtd->owner = THIS_MODULE; + mtd->dev.parent = &pdev->dev; + mtd->name = DRIVER_NAME; + + /* 50 us command delay time */ + this->chip_delay = 5; + + this->priv = host; + this->dev_ready = mxc_nand_dev_ready; + this->cmdfunc = mxc_nand_command; + this->read_byte = mxc_nand_read_byte; + this->read_word = mxc_nand_read_word; + this->write_buf = mxc_nand_write_buf; + this->read_buf = mxc_nand_read_buf; + + host->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(host->clk)) + return PTR_ERR(host->clk); + + err = mxcnd_probe_dt(host); + if (err > 0) { + struct mxc_nand_platform_data *pdata = + dev_get_platdata(&pdev->dev); + if (pdata) { + host->pdata = *pdata; + host->devtype_data = (struct mxc_nand_devtype_data *) + pdev->id_entry->driver_data; + } else { + err = -ENODEV; + } + } + if (err < 0) + return err; + + if (host->devtype_data->needs_ip) { + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->regs_ip = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->regs_ip)) + return PTR_ERR(host->regs_ip); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + } else { + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + } + + host->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(host->base)) + return PTR_ERR(host->base); + + host->main_area0 = host->base; + + if (host->devtype_data->regs_offset) + host->regs = host->base + host->devtype_data->regs_offset; + host->spare0 = host->base + host->devtype_data->spare0_offset; + if (host->devtype_data->axi_offset) + host->regs_axi = host->base + host->devtype_data->axi_offset; + + this->ecc.bytes = host->devtype_data->eccbytes; + host->eccsize = host->devtype_data->eccsize; + + this->select_chip = host->devtype_data->select_chip; + this->ecc.size = 512; + this->ecc.layout = host->devtype_data->ecclayout_512; + + if (host->pdata.hw_ecc) { + this->ecc.calculate = mxc_nand_calculate_ecc; + this->ecc.hwctl = mxc_nand_enable_hwecc; + this->ecc.correct = host->devtype_data->correct_data; + this->ecc.mode = NAND_ECC_HW; + } else { + this->ecc.mode = NAND_ECC_SOFT; + } + + /* NAND bus width determines access functions used by upper layer */ + if (host->pdata.width == 2) + this->options |= NAND_BUSWIDTH_16; + + if (host->pdata.flash_bbt) { + this->bbt_td = &bbt_main_descr; + this->bbt_md = &bbt_mirror_descr; + /* update flash based bbt */ + this->bbt_options |= NAND_BBT_USE_FLASH; + } + + init_completion(&host->op_completion); + + host->irq = platform_get_irq(pdev, 0); + if (host->irq < 0) + return host->irq; + + /* + * Use host->devtype_data->irq_control() here instead of irq_control() + * because we must not disable_irq_nosync without having requested the + * irq. + */ + host->devtype_data->irq_control(host, 0); + + err = devm_request_irq(&pdev->dev, host->irq, mxc_nfc_irq, + 0, DRIVER_NAME, host); + if (err) + return err; + + err = clk_prepare_enable(host->clk); + if (err) + return err; + host->clk_act = 1; + + /* + * Now that we "own" the interrupt make sure the interrupt mask bit is + * cleared on i.MX21. Otherwise we can't read the interrupt status bit + * on this machine. + */ + if (host->devtype_data->irqpending_quirk) { + disable_irq_nosync(host->irq); + host->devtype_data->irq_control(host, 1); + } + + /* first scan to find the device and get the page size */ + if (nand_scan_ident(mtd, is_imx25_nfc(host) ? 4 : 1, NULL)) { + err = -ENXIO; + goto escan; + } + + /* allocate the right size buffer now */ + devm_kfree(&pdev->dev, (void *)host->data_buf); + host->data_buf = devm_kzalloc(&pdev->dev, mtd->writesize + mtd->oobsize, + GFP_KERNEL); + if (!host->data_buf) { + err = -ENOMEM; + goto escan; + } + + /* Call preset again, with correct writesize this time */ + host->devtype_data->preset(mtd); + + if (mtd->writesize == 2048) + this->ecc.layout = host->devtype_data->ecclayout_2k; + else if (mtd->writesize == 4096) + this->ecc.layout = host->devtype_data->ecclayout_4k; + + if (this->ecc.mode == NAND_ECC_HW) { + if (is_imx21_nfc(host) || is_imx27_nfc(host)) + this->ecc.strength = 1; + else + this->ecc.strength = (host->eccsize == 4) ? 4 : 8; + } + + /* second phase scan */ + if (nand_scan_tail(mtd)) { + err = -ENXIO; + goto escan; + } + + /* Register the partitions */ + mtd_device_parse_register(mtd, part_probes, + &(struct mtd_part_parser_data){ + .of_node = pdev->dev.of_node, + }, + host->pdata.parts, + host->pdata.nr_parts); + + platform_set_drvdata(pdev, host); + + return 0; + +escan: + if (host->clk_act) + clk_disable_unprepare(host->clk); + + return err; +} + +static int mxcnd_remove(struct platform_device *pdev) +{ + struct mxc_nand_host *host = platform_get_drvdata(pdev); + + nand_release(&host->mtd); + if (host->clk_act) + clk_disable_unprepare(host->clk); + + return 0; +} + +static struct platform_driver mxcnd_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(mxcnd_dt_ids), + }, + .id_table = mxcnd_devtype, + .probe = mxcnd_probe, + .remove = mxcnd_remove, +}; +module_platform_driver(mxcnd_driver); + +MODULE_AUTHOR("Freescale Semiconductor, Inc."); +MODULE_DESCRIPTION("MXC NAND MTD driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c new file mode 100644 index 000000000..c2e1232cd --- /dev/null +++ b/drivers/mtd/nand/nand_base.c @@ -0,0 +1,4286 @@ +/* + * drivers/mtd/nand.c + * + * Overview: + * This is the generic MTD driver for NAND flash devices. It should be + * capable of working with almost all NAND chips currently available. + * + * Additional technical information is available on + * http://www.linux-mtd.infradead.org/doc/nand.html + * + * Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com) + * 2002-2006 Thomas Gleixner (tglx@linutronix.de) + * + * Credits: + * David Woodhouse for adding multichip support + * + * Aleph One Ltd. and Toby Churchill Ltd. for supporting the + * rework for 2K page size chips + * + * TODO: + * Enable cached programming for 2k page size chips + * Check, if mtd->ecctype should be set to MTD_ECC_HW + * if we have HW ECC support. + * BBT table is not serialized, has to be fixed + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/mm.h> +#include <linux/types.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/nand_bch.h> +#include <linux/interrupt.h> +#include <linux/bitops.h> +#include <linux/leds.h> +#include <linux/io.h> +#include <linux/mtd/partitions.h> + +/* Define default oob placement schemes for large and small page devices */ +static struct nand_ecclayout nand_oob_8 = { + .eccbytes = 3, + .eccpos = {0, 1, 2}, + .oobfree = { + {.offset = 3, + .length = 2}, + {.offset = 6, + .length = 2} } +}; + +static struct nand_ecclayout nand_oob_16 = { + .eccbytes = 6, + .eccpos = {0, 1, 2, 3, 6, 7}, + .oobfree = { + {.offset = 8, + . length = 8} } +}; + +static struct nand_ecclayout nand_oob_64 = { + .eccbytes = 24, + .eccpos = { + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { + {.offset = 2, + .length = 38} } +}; + +static struct nand_ecclayout nand_oob_128 = { + .eccbytes = 48, + .eccpos = { + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127}, + .oobfree = { + {.offset = 2, + .length = 78} } +}; + +static int nand_get_device(struct mtd_info *mtd, int new_state); + +static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); + +/* + * For devices which display every fart in the system on a separate LED. Is + * compiled away when LED support is disabled. + */ +DEFINE_LED_TRIGGER(nand_led_trigger); + +static int check_offs_len(struct mtd_info *mtd, + loff_t ofs, uint64_t len) +{ + struct nand_chip *chip = mtd->priv; + int ret = 0; + + /* Start address must align on block boundary */ + if (ofs & ((1ULL << chip->phys_erase_shift) - 1)) { + pr_debug("%s: unaligned address\n", __func__); + ret = -EINVAL; + } + + /* Length must align on block boundary */ + if (len & ((1ULL << chip->phys_erase_shift) - 1)) { + pr_debug("%s: length not block aligned\n", __func__); + ret = -EINVAL; + } + + return ret; +} + +/** + * nand_release_device - [GENERIC] release chip + * @mtd: MTD device structure + * + * Release chip lock and wake up anyone waiting on the device. + */ +static void nand_release_device(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + + /* Release the controller and the chip */ + spin_lock(&chip->controller->lock); + chip->controller->active = NULL; + chip->state = FL_READY; + wake_up(&chip->controller->wq); + spin_unlock(&chip->controller->lock); +} + +/** + * nand_read_byte - [DEFAULT] read one byte from the chip + * @mtd: MTD device structure + * + * Default read function for 8bit buswidth + */ +static uint8_t nand_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + return readb(chip->IO_ADDR_R); +} + +/** + * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip + * @mtd: MTD device structure + * + * Default read function for 16bit buswidth with endianness conversion. + * + */ +static uint8_t nand_read_byte16(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + return (uint8_t) cpu_to_le16(readw(chip->IO_ADDR_R)); +} + +/** + * nand_read_word - [DEFAULT] read one word from the chip + * @mtd: MTD device structure + * + * Default read function for 16bit buswidth without endianness conversion. + */ +static u16 nand_read_word(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + return readw(chip->IO_ADDR_R); +} + +/** + * nand_select_chip - [DEFAULT] control CE line + * @mtd: MTD device structure + * @chipnr: chipnumber to select, -1 for deselect + * + * Default select function for 1 chip devices. + */ +static void nand_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct nand_chip *chip = mtd->priv; + + switch (chipnr) { + case -1: + chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); + break; + case 0: + break; + + default: + BUG(); + } +} + +/** + * nand_write_byte - [DEFAULT] write single byte to chip + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] + */ +static void nand_write_byte(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + + chip->write_buf(mtd, &byte, 1); +} + +/** + * nand_write_byte16 - [DEFAULT] write single byte to a chip with width 16 + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] on a 16-bit wide chip. + */ +static void nand_write_byte16(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + uint16_t word = byte; + + /* + * It's not entirely clear what should happen to I/O[15:8] when writing + * a byte. The ONFi spec (Revision 3.1; 2012-09-19, Section 2.16) reads: + * + * When the host supports a 16-bit bus width, only data is + * transferred at the 16-bit width. All address and command line + * transfers shall use only the lower 8-bits of the data bus. During + * command transfers, the host may place any value on the upper + * 8-bits of the data bus. During address transfers, the host shall + * set the upper 8-bits of the data bus to 00h. + * + * One user of the write_byte callback is nand_onfi_set_features. The + * four parameters are specified to be written to I/O[7:0], but this is + * neither an address nor a command transfer. Let's assume a 0 on the + * upper I/O lines is OK. + */ + chip->write_buf(mtd, (uint8_t *)&word, 2); +} + +/** + * nand_write_buf - [DEFAULT] write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + * + * Default write function for 8bit buswidth. + */ +static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + iowrite8_rep(chip->IO_ADDR_W, buf, len); +} + +/** + * nand_read_buf - [DEFAULT] read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + * + * Default read function for 8bit buswidth. + */ +static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + ioread8_rep(chip->IO_ADDR_R, buf, len); +} + +/** + * nand_write_buf16 - [DEFAULT] write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + * + * Default write function for 16bit buswidth. + */ +static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + u16 *p = (u16 *) buf; + + iowrite16_rep(chip->IO_ADDR_W, p, len >> 1); +} + +/** + * nand_read_buf16 - [DEFAULT] read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + * + * Default read function for 16bit buswidth. + */ +static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + u16 *p = (u16 *) buf; + + ioread16_rep(chip->IO_ADDR_R, p, len >> 1); +} + +/** + * nand_block_bad - [DEFAULT] Read bad block marker from the chip + * @mtd: MTD device structure + * @ofs: offset from device start + * @getchip: 0, if the chip is already selected + * + * Check, if the block is bad. + */ +static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + int page, chipnr, res = 0, i = 0; + struct nand_chip *chip = mtd->priv; + u16 bad; + + if (chip->bbt_options & NAND_BBT_SCANLASTPAGE) + ofs += mtd->erasesize - mtd->writesize; + + page = (int)(ofs >> chip->page_shift) & chip->pagemask; + + if (getchip) { + chipnr = (int)(ofs >> chip->chip_shift); + + nand_get_device(mtd, FL_READING); + + /* Select the NAND device */ + chip->select_chip(mtd, chipnr); + } + + do { + if (chip->options & NAND_BUSWIDTH_16) { + chip->cmdfunc(mtd, NAND_CMD_READOOB, + chip->badblockpos & 0xFE, page); + bad = cpu_to_le16(chip->read_word(mtd)); + if (chip->badblockpos & 0x1) + bad >>= 8; + else + bad &= 0xFF; + } else { + chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos, + page); + bad = chip->read_byte(mtd); + } + + if (likely(chip->badblockbits == 8)) + res = bad != 0xFF; + else + res = hweight8(bad) < chip->badblockbits; + ofs += mtd->writesize; + page = (int)(ofs >> chip->page_shift) & chip->pagemask; + i++; + } while (!res && i < 2 && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE)); + + if (getchip) { + chip->select_chip(mtd, -1); + nand_release_device(mtd); + } + + return res; +} + +/** + * nand_default_block_markbad - [DEFAULT] mark a block bad via bad block marker + * @mtd: MTD device structure + * @ofs: offset from device start + * + * This is the default implementation, which can be overridden by a hardware + * specific driver. It provides the details for writing a bad block marker to a + * block. + */ +static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd->priv; + struct mtd_oob_ops ops; + uint8_t buf[2] = { 0, 0 }; + int ret = 0, res, i = 0; + + memset(&ops, 0, sizeof(ops)); + ops.oobbuf = buf; + ops.ooboffs = chip->badblockpos; + if (chip->options & NAND_BUSWIDTH_16) { + ops.ooboffs &= ~0x01; + ops.len = ops.ooblen = 2; + } else { + ops.len = ops.ooblen = 1; + } + ops.mode = MTD_OPS_PLACE_OOB; + + /* Write to first/last page(s) if necessary */ + if (chip->bbt_options & NAND_BBT_SCANLASTPAGE) + ofs += mtd->erasesize - mtd->writesize; + do { + res = nand_do_write_oob(mtd, ofs, &ops); + if (!ret) + ret = res; + + i++; + ofs += mtd->writesize; + } while ((chip->bbt_options & NAND_BBT_SCAN2NDPAGE) && i < 2); + + return ret; +} + +/** + * nand_block_markbad_lowlevel - mark a block bad + * @mtd: MTD device structure + * @ofs: offset from device start + * + * This function performs the generic NAND bad block marking steps (i.e., bad + * block table(s) and/or marker(s)). We only allow the hardware driver to + * specify how to write bad block markers to OOB (chip->block_markbad). + * + * We try operations in the following order: + * (1) erase the affected block, to allow OOB marker to be written cleanly + * (2) write bad block marker to OOB area of affected block (unless flag + * NAND_BBT_NO_OOB_BBM is present) + * (3) update the BBT + * Note that we retain the first error encountered in (2) or (3), finish the + * procedures, and dump the error in the end. +*/ +static int nand_block_markbad_lowlevel(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd->priv; + int res, ret = 0; + + if (!(chip->bbt_options & NAND_BBT_NO_OOB_BBM)) { + struct erase_info einfo; + + /* Attempt erase before marking OOB */ + memset(&einfo, 0, sizeof(einfo)); + einfo.mtd = mtd; + einfo.addr = ofs; + einfo.len = 1ULL << chip->phys_erase_shift; + nand_erase_nand(mtd, &einfo, 0); + + /* Write bad block marker to OOB */ + nand_get_device(mtd, FL_WRITING); + ret = chip->block_markbad(mtd, ofs); + nand_release_device(mtd); + } + + /* Mark block bad in BBT */ + if (chip->bbt) { + res = nand_markbad_bbt(mtd, ofs); + if (!ret) + ret = res; + } + + if (!ret) + mtd->ecc_stats.badblocks++; + + return ret; +} + +/** + * nand_check_wp - [GENERIC] check if the chip is write protected + * @mtd: MTD device structure + * + * Check, if the device is write protected. The function expects, that the + * device is already selected. + */ +static int nand_check_wp(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + + /* Broken xD cards report WP despite being writable */ + if (chip->options & NAND_BROKEN_XD) + return 0; + + /* Check the WP bit */ + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; +} + +/** + * nand_block_isreserved - [GENERIC] Check if a block is marked reserved. + * @mtd: MTD device structure + * @ofs: offset from device start + * + * Check if the block is marked as reserved. + */ +static int nand_block_isreserved(struct mtd_info *mtd, loff_t ofs) +{ + struct nand_chip *chip = mtd->priv; + + if (!chip->bbt) + return 0; + /* Return info from the table */ + return nand_isreserved_bbt(mtd, ofs); +} + +/** + * nand_block_checkbad - [GENERIC] Check if a block is marked bad + * @mtd: MTD device structure + * @ofs: offset from device start + * @getchip: 0, if the chip is already selected + * @allowbbt: 1, if its allowed to access the bbt area + * + * Check, if the block is bad. Either by reading the bad block table or + * calling of the scan function. + */ +static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip, + int allowbbt) +{ + struct nand_chip *chip = mtd->priv; + + if (!chip->bbt) + return chip->block_bad(mtd, ofs, getchip); + + /* Return info from the table */ + return nand_isbad_bbt(mtd, ofs, allowbbt); +} + +/** + * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands. + * @mtd: MTD device structure + * @timeo: Timeout + * + * Helper function for nand_wait_ready used when needing to wait in interrupt + * context. + */ +static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo) +{ + struct nand_chip *chip = mtd->priv; + int i; + + /* Wait for the device to get ready */ + for (i = 0; i < timeo; i++) { + if (chip->dev_ready(mtd)) + break; + touch_softlockup_watchdog(); + mdelay(1); + } +} + +/* Wait for the ready pin, after a command. The timeout is caught later. */ +void nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + unsigned long timeo = jiffies + msecs_to_jiffies(20); + + /* 400ms timeout */ + if (in_interrupt() || oops_in_progress) + return panic_nand_wait_ready(mtd, 400); + + led_trigger_event(nand_led_trigger, LED_FULL); + /* Wait until command is processed or timeout occurs */ + do { + if (chip->dev_ready(mtd)) + break; + touch_softlockup_watchdog(); + } while (time_before(jiffies, timeo)); + led_trigger_event(nand_led_trigger, LED_OFF); +} +EXPORT_SYMBOL_GPL(nand_wait_ready); + +/** + * nand_wait_status_ready - [GENERIC] Wait for the ready status after commands. + * @mtd: MTD device structure + * @timeo: Timeout in ms + * + * Wait for status ready (i.e. command done) or timeout. + */ +static void nand_wait_status_ready(struct mtd_info *mtd, unsigned long timeo) +{ + register struct nand_chip *chip = mtd->priv; + + timeo = jiffies + msecs_to_jiffies(timeo); + do { + if ((chip->read_byte(mtd) & NAND_STATUS_READY)) + break; + touch_softlockup_watchdog(); + } while (time_before(jiffies, timeo)); +}; + +/** + * nand_command - [DEFAULT] Send command to NAND device + * @mtd: MTD device structure + * @command: the command to be sent + * @column: the column address for this command, -1 if none + * @page_addr: the page address for this command, -1 if none + * + * Send command to NAND device. This function is used for small page devices + * (512 Bytes per page). + */ +static void nand_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + register struct nand_chip *chip = mtd->priv; + int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE; + + /* Write out the command to the device */ + if (command == NAND_CMD_SEQIN) { + int readcmd; + + if (column >= mtd->writesize) { + /* OOB area */ + column -= mtd->writesize; + readcmd = NAND_CMD_READOOB; + } else if (column < 256) { + /* First 256 bytes --> READ0 */ + readcmd = NAND_CMD_READ0; + } else { + column -= 256; + readcmd = NAND_CMD_READ1; + } + chip->cmd_ctrl(mtd, readcmd, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + } + chip->cmd_ctrl(mtd, command, ctrl); + + /* Address cycle, when necessary */ + ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE; + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + chip->cmd_ctrl(mtd, column, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + } + if (page_addr != -1) { + chip->cmd_ctrl(mtd, page_addr, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + chip->cmd_ctrl(mtd, page_addr >> 8, ctrl); + /* One more address cycle for devices > 32MiB */ + if (chip->chipsize > (32 << 20)) + chip->cmd_ctrl(mtd, page_addr >> 16, ctrl); + } + chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + /* + * Program and erase have their own busy handlers status and sequential + * in needs no delay + */ + switch (command) { + + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + if (chip->dev_ready) + break; + udelay(chip->chip_delay); + chip->cmd_ctrl(mtd, NAND_CMD_STATUS, + NAND_CTRL_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, + NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + /* EZ-NAND can take upto 250ms as per ONFi v4.0 */ + nand_wait_status_ready(mtd, 250); + return; + + /* This applies to read commands */ + default: + /* + * If we don't have access to the busy pin, we apply the given + * command delay + */ + if (!chip->dev_ready) { + udelay(chip->chip_delay); + return; + } + } + /* + * Apply this short delay always to ensure that we do wait tWB in + * any case on any machine. + */ + ndelay(100); + + nand_wait_ready(mtd); +} + +/** + * nand_command_lp - [DEFAULT] Send command to NAND large page device + * @mtd: MTD device structure + * @command: the command to be sent + * @column: the column address for this command, -1 if none + * @page_addr: the page address for this command, -1 if none + * + * Send command to NAND device. This is the version for the new large page + * devices. We don't have the separate regions as we have in the small page + * devices. We must emulate NAND_CMD_READOOB to keep the code compatible. + */ +static void nand_command_lp(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + register struct nand_chip *chip = mtd->priv; + + /* Emulate NAND_CMD_READOOB */ + if (command == NAND_CMD_READOOB) { + column += mtd->writesize; + command = NAND_CMD_READ0; + } + + /* Command latch cycle */ + chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + + if (column != -1 || page_addr != -1) { + int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE; + + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + chip->cmd_ctrl(mtd, column, ctrl); + ctrl &= ~NAND_CTRL_CHANGE; + chip->cmd_ctrl(mtd, column >> 8, ctrl); + } + if (page_addr != -1) { + chip->cmd_ctrl(mtd, page_addr, ctrl); + chip->cmd_ctrl(mtd, page_addr >> 8, + NAND_NCE | NAND_ALE); + /* One more address cycle for devices > 128MiB */ + if (chip->chipsize > (128 << 20)) + chip->cmd_ctrl(mtd, page_addr >> 16, + NAND_NCE | NAND_ALE); + } + } + chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + /* + * Program and erase have their own busy handlers status, sequential + * in and status need no delay. + */ + switch (command) { + + case NAND_CMD_CACHEDPROG: + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_RNDIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + if (chip->dev_ready) + break; + udelay(chip->chip_delay); + chip->cmd_ctrl(mtd, NAND_CMD_STATUS, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + /* EZ-NAND can take upto 250ms as per ONFi v4.0 */ + nand_wait_status_ready(mtd, 250); + return; + + case NAND_CMD_RNDOUT: + /* No ready / busy check necessary */ + chip->cmd_ctrl(mtd, NAND_CMD_RNDOUTSTART, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + return; + + case NAND_CMD_READ0: + chip->cmd_ctrl(mtd, NAND_CMD_READSTART, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + chip->cmd_ctrl(mtd, NAND_CMD_NONE, + NAND_NCE | NAND_CTRL_CHANGE); + + /* This applies to read commands */ + default: + /* + * If we don't have access to the busy pin, we apply the given + * command delay. + */ + if (!chip->dev_ready) { + udelay(chip->chip_delay); + return; + } + } + + /* + * Apply this short delay always to ensure that we do wait tWB in + * any case on any machine. + */ + ndelay(100); + + nand_wait_ready(mtd); +} + +/** + * panic_nand_get_device - [GENERIC] Get chip for selected access + * @chip: the nand chip descriptor + * @mtd: MTD device structure + * @new_state: the state which is requested + * + * Used when in panic, no locks are taken. + */ +static void panic_nand_get_device(struct nand_chip *chip, + struct mtd_info *mtd, int new_state) +{ + /* Hardware controller shared among independent devices */ + chip->controller->active = chip; + chip->state = new_state; +} + +/** + * nand_get_device - [GENERIC] Get chip for selected access + * @mtd: MTD device structure + * @new_state: the state which is requested + * + * Get the device and lock it for exclusive access + */ +static int +nand_get_device(struct mtd_info *mtd, int new_state) +{ + struct nand_chip *chip = mtd->priv; + spinlock_t *lock = &chip->controller->lock; + wait_queue_head_t *wq = &chip->controller->wq; + DECLARE_WAITQUEUE(wait, current); +retry: + spin_lock(lock); + + /* Hardware controller shared among independent devices */ + if (!chip->controller->active) + chip->controller->active = chip; + + if (chip->controller->active == chip && chip->state == FL_READY) { + chip->state = new_state; + spin_unlock(lock); + return 0; + } + if (new_state == FL_PM_SUSPENDED) { + if (chip->controller->active->state == FL_PM_SUSPENDED) { + chip->state = FL_PM_SUSPENDED; + spin_unlock(lock); + return 0; + } + } + set_current_state(TASK_UNINTERRUPTIBLE); + add_wait_queue(wq, &wait); + spin_unlock(lock); + schedule(); + remove_wait_queue(wq, &wait); + goto retry; +} + +/** + * panic_nand_wait - [GENERIC] wait until the command is done + * @mtd: MTD device structure + * @chip: NAND chip structure + * @timeo: timeout + * + * Wait for command done. This is a helper function for nand_wait used when + * we are in interrupt context. May happen when in panic and trying to write + * an oops through mtdoops. + */ +static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip, + unsigned long timeo) +{ + int i; + for (i = 0; i < timeo; i++) { + if (chip->dev_ready) { + if (chip->dev_ready(mtd)) + break; + } else { + if (chip->read_byte(mtd) & NAND_STATUS_READY) + break; + } + mdelay(1); + } +} + +/** + * nand_wait - [DEFAULT] wait until the command is done + * @mtd: MTD device structure + * @chip: NAND chip structure + * + * Wait for command done. This applies to erase and program only. Erase can + * take up to 400ms and program up to 20ms according to general NAND and + * SmartMedia specs. + */ +static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + + int status, state = chip->state; + unsigned long timeo = (state == FL_ERASING ? 400 : 20); + + led_trigger_event(nand_led_trigger, LED_FULL); + + /* + * Apply this short delay always to ensure that we do wait tWB in any + * case on any machine. + */ + ndelay(100); + + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + + if (in_interrupt() || oops_in_progress) + panic_nand_wait(mtd, chip, timeo); + else { + timeo = jiffies + msecs_to_jiffies(timeo); + while (time_before(jiffies, timeo)) { + if (chip->dev_ready) { + if (chip->dev_ready(mtd)) + break; + } else { + if (chip->read_byte(mtd) & NAND_STATUS_READY) + break; + } + cond_resched(); + } + } + led_trigger_event(nand_led_trigger, LED_OFF); + + status = (int)chip->read_byte(mtd); + /* This can happen if in case of timeout or buggy dev_ready */ + WARN_ON(!(status & NAND_STATUS_READY)); + return status; +} + +/** + * __nand_unlock - [REPLACEABLE] unlocks specified locked blocks + * @mtd: mtd info + * @ofs: offset to start unlock from + * @len: length to unlock + * @invert: when = 0, unlock the range of blocks within the lower and + * upper boundary address + * when = 1, unlock the range of blocks outside the boundaries + * of the lower and upper boundary address + * + * Returs unlock status. + */ +static int __nand_unlock(struct mtd_info *mtd, loff_t ofs, + uint64_t len, int invert) +{ + int ret = 0; + int status, page; + struct nand_chip *chip = mtd->priv; + + /* Submit address of first page to unlock */ + page = ofs >> chip->page_shift; + chip->cmdfunc(mtd, NAND_CMD_UNLOCK1, -1, page & chip->pagemask); + + /* Submit address of last page to unlock */ + page = (ofs + len) >> chip->page_shift; + chip->cmdfunc(mtd, NAND_CMD_UNLOCK2, -1, + (page | invert) & chip->pagemask); + + /* Call wait ready function */ + status = chip->waitfunc(mtd, chip); + /* See if device thinks it succeeded */ + if (status & NAND_STATUS_FAIL) { + pr_debug("%s: error status = 0x%08x\n", + __func__, status); + ret = -EIO; + } + + return ret; +} + +/** + * nand_unlock - [REPLACEABLE] unlocks specified locked blocks + * @mtd: mtd info + * @ofs: offset to start unlock from + * @len: length to unlock + * + * Returns unlock status. + */ +int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len) +{ + int ret = 0; + int chipnr; + struct nand_chip *chip = mtd->priv; + + pr_debug("%s: start = 0x%012llx, len = %llu\n", + __func__, (unsigned long long)ofs, len); + + if (check_offs_len(mtd, ofs, len)) + return -EINVAL; + + /* Align to last block address if size addresses end of the device */ + if (ofs + len == mtd->size) + len -= mtd->erasesize; + + nand_get_device(mtd, FL_UNLOCKING); + + /* Shift to get chip number */ + chipnr = ofs >> chip->chip_shift; + + chip->select_chip(mtd, chipnr); + + /* + * Reset the chip. + * If we want to check the WP through READ STATUS and check the bit 7 + * we must reset the chip + * some operation can also clear the bit 7 of status register + * eg. erase/program a locked block + */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) { + pr_debug("%s: device is write protected!\n", + __func__); + ret = -EIO; + goto out; + } + + ret = __nand_unlock(mtd, ofs, len, 0); + +out: + chip->select_chip(mtd, -1); + nand_release_device(mtd); + + return ret; +} +EXPORT_SYMBOL(nand_unlock); + +/** + * nand_lock - [REPLACEABLE] locks all blocks present in the device + * @mtd: mtd info + * @ofs: offset to start unlock from + * @len: length to unlock + * + * This feature is not supported in many NAND parts. 'Micron' NAND parts do + * have this feature, but it allows only to lock all blocks, not for specified + * range for block. Implementing 'lock' feature by making use of 'unlock', for + * now. + * + * Returns lock status. + */ +int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len) +{ + int ret = 0; + int chipnr, status, page; + struct nand_chip *chip = mtd->priv; + + pr_debug("%s: start = 0x%012llx, len = %llu\n", + __func__, (unsigned long long)ofs, len); + + if (check_offs_len(mtd, ofs, len)) + return -EINVAL; + + nand_get_device(mtd, FL_LOCKING); + + /* Shift to get chip number */ + chipnr = ofs >> chip->chip_shift; + + chip->select_chip(mtd, chipnr); + + /* + * Reset the chip. + * If we want to check the WP through READ STATUS and check the bit 7 + * we must reset the chip + * some operation can also clear the bit 7 of status register + * eg. erase/program a locked block + */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) { + pr_debug("%s: device is write protected!\n", + __func__); + status = MTD_ERASE_FAILED; + ret = -EIO; + goto out; + } + + /* Submit address of first page to lock */ + page = ofs >> chip->page_shift; + chip->cmdfunc(mtd, NAND_CMD_LOCK, -1, page & chip->pagemask); + + /* Call wait ready function */ + status = chip->waitfunc(mtd, chip); + /* See if device thinks it succeeded */ + if (status & NAND_STATUS_FAIL) { + pr_debug("%s: error status = 0x%08x\n", + __func__, status); + ret = -EIO; + goto out; + } + + ret = __nand_unlock(mtd, ofs, len, 0x1); + +out: + chip->select_chip(mtd, -1); + nand_release_device(mtd); + + return ret; +} +EXPORT_SYMBOL(nand_lock); + +/** + * nand_read_page_raw - [INTERN] read raw page data without ecc + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Not for syndrome calculating ECC controllers, which use a special oob layout. + */ +static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + chip->read_buf(mtd, buf, mtd->writesize); + if (oob_required) + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +/** + * nand_read_page_raw_syndrome - [INTERN] read raw page data without ecc + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * We need a special oob layout and handling even when OOB isn't used. + */ +static int nand_read_page_raw_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + int eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + uint8_t *oob = chip->oob_poi; + int steps, size; + + for (steps = chip->ecc.steps; steps > 0; steps--) { + chip->read_buf(mtd, buf, eccsize); + buf += eccsize; + + if (chip->ecc.prepad) { + chip->read_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->read_buf(mtd, oob, eccbytes); + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->read_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; + } + } + + size = mtd->oobsize - (oob - chip->oob_poi); + if (size) + chip->read_buf(mtd, oob, size); + + return 0; +} + +/** + * nand_read_page_swecc - [REPLACEABLE] software ECC based page read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + */ +static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + unsigned int max_bitflips = 0; + + chip->ecc.read_page_raw(mtd, chip, buf, 1, page); + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + + for (i = 0; i < chip->ecc.total; i++) + ecc_code[i] = chip->oob_poi[eccpos[i]]; + + eccsteps = chip->ecc.steps; + p = buf; + + for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + } + return max_bitflips; +} + +/** + * nand_read_subpage - [REPLACEABLE] ECC based sub-page read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @data_offs: offset of requested data within the page + * @readlen: data length + * @bufpoi: buffer to store read data + * @page: page number to read + */ +static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi, + int page) +{ + int start_step, end_step, num_steps; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint8_t *p; + int data_col_addr, i, gaps = 0; + int datafrag_len, eccfrag_len, aligned_len, aligned_pos; + int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1; + int index; + unsigned int max_bitflips = 0; + + /* Column address within the page aligned to ECC size (256bytes) */ + start_step = data_offs / chip->ecc.size; + end_step = (data_offs + readlen - 1) / chip->ecc.size; + num_steps = end_step - start_step + 1; + index = start_step * chip->ecc.bytes; + + /* Data size aligned to ECC ecc.size */ + datafrag_len = num_steps * chip->ecc.size; + eccfrag_len = num_steps * chip->ecc.bytes; + + data_col_addr = start_step * chip->ecc.size; + /* If we read not a page aligned data */ + if (data_col_addr != 0) + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_col_addr, -1); + + p = bufpoi + data_col_addr; + chip->read_buf(mtd, p, datafrag_len); + + /* Calculate ECC */ + for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) + chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]); + + /* + * The performance is faster if we position offsets according to + * ecc.pos. Let's make sure that there are no gaps in ECC positions. + */ + for (i = 0; i < eccfrag_len - 1; i++) { + if (eccpos[i + index] + 1 != eccpos[i + index + 1]) { + gaps = 1; + break; + } + } + if (gaps) { + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + } else { + /* + * Send the command to read the particular ECC bytes take care + * about buswidth alignment in read_buf. + */ + aligned_pos = eccpos[index] & ~(busw - 1); + aligned_len = eccfrag_len; + if (eccpos[index] & (busw - 1)) + aligned_len++; + if (eccpos[index + (num_steps * chip->ecc.bytes)] & (busw - 1)) + aligned_len++; + + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, + mtd->writesize + aligned_pos, -1); + chip->read_buf(mtd, &chip->oob_poi[aligned_pos], aligned_len); + } + + for (i = 0; i < eccfrag_len; i++) + chip->buffers->ecccode[i] = chip->oob_poi[eccpos[i + index]]; + + p = bufpoi + data_col_addr; + for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) { + int stat; + + stat = chip->ecc.correct(mtd, p, + &chip->buffers->ecccode[i], &chip->buffers->ecccalc[i]); + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + } + return max_bitflips; +} + +/** + * nand_read_page_hwecc - [REPLACEABLE] hardware ECC based page read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Not for syndrome calculating ECC controllers which need a special oob layout. + */ +static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + unsigned int max_bitflips = 0; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + } + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + for (i = 0; i < chip->ecc.total; i++) + ecc_code[i] = chip->oob_poi[eccpos[i]]; + + eccsteps = chip->ecc.steps; + p = buf; + + for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + } + return max_bitflips; +} + +/** + * nand_read_page_hwecc_oob_first - [REPLACEABLE] hw ecc, read oob first + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Hardware ECC for large page chips, require OOB to be read first. For this + * ECC mode, the write_page method is re-used from ECC_HW. These methods + * read/write ECC from the OOB area, unlike the ECC_HW_SYNDROME support with + * multiple ECC steps, follows the "infix ECC" scheme and reads/writes ECC from + * the data area, by overwriting the NAND manufacturer bad block markings. + */ +static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, int page) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint8_t *ecc_calc = chip->buffers->ecccalc; + unsigned int max_bitflips = 0; + + /* Read the OOB area first */ + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + + for (i = 0; i < chip->ecc.total; i++) + ecc_code[i] = chip->oob_poi[eccpos[i]]; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + + stat = chip->ecc.correct(mtd, p, &ecc_code[i], NULL); + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + } + return max_bitflips; +} + +/** + * nand_read_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page read + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * The hw generator calculates the error syndrome automatically. Therefore we + * need a special oob layout and handling. + */ +static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *p = buf; + uint8_t *oob = chip->oob_poi; + unsigned int max_bitflips = 0; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + int stat; + + chip->ecc.hwctl(mtd, NAND_ECC_READ); + chip->read_buf(mtd, p, eccsize); + + if (chip->ecc.prepad) { + chip->read_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->ecc.hwctl(mtd, NAND_ECC_READSYN); + chip->read_buf(mtd, oob, eccbytes); + stat = chip->ecc.correct(mtd, p, oob, NULL); + + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->read_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; + } + } + + /* Calculate remaining oob bytes */ + i = mtd->oobsize - (oob - chip->oob_poi); + if (i) + chip->read_buf(mtd, oob, i); + + return max_bitflips; +} + +/** + * nand_transfer_oob - [INTERN] Transfer oob to client buffer + * @chip: nand chip structure + * @oob: oob destination address + * @ops: oob ops structure + * @len: size of oob to transfer + */ +static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob, + struct mtd_oob_ops *ops, size_t len) +{ + switch (ops->mode) { + + case MTD_OPS_PLACE_OOB: + case MTD_OPS_RAW: + memcpy(oob, chip->oob_poi + ops->ooboffs, len); + return oob + len; + + case MTD_OPS_AUTO_OOB: { + struct nand_oobfree *free = chip->ecc.layout->oobfree; + uint32_t boffs = 0, roffs = ops->ooboffs; + size_t bytes = 0; + + for (; free->length && len; free++, len -= bytes) { + /* Read request not from offset 0? */ + if (unlikely(roffs)) { + if (roffs >= free->length) { + roffs -= free->length; + continue; + } + boffs = free->offset + roffs; + bytes = min_t(size_t, len, + (free->length - roffs)); + roffs = 0; + } else { + bytes = min_t(size_t, len, free->length); + boffs = free->offset; + } + memcpy(oob, chip->oob_poi + boffs, bytes); + oob += bytes; + } + return oob; + } + default: + BUG(); + } + return NULL; +} + +/** + * nand_setup_read_retry - [INTERN] Set the READ RETRY mode + * @mtd: MTD device structure + * @retry_mode: the retry mode to use + * + * Some vendors supply a special command to shift the Vt threshold, to be used + * when there are too many bitflips in a page (i.e., ECC error). After setting + * a new threshold, the host should retry reading the page. + */ +static int nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + + pr_debug("setting READ RETRY mode %d\n", retry_mode); + + if (retry_mode >= chip->read_retries) + return -EINVAL; + + if (!chip->setup_read_retry) + return -EOPNOTSUPP; + + return chip->setup_read_retry(mtd, retry_mode); +} + +/** + * nand_do_read_ops - [INTERN] Read data with ECC + * @mtd: MTD device structure + * @from: offset to read from + * @ops: oob ops structure + * + * Internal function. Called with chip held. + */ +static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) +{ + int chipnr, page, realpage, col, bytes, aligned, oob_required; + struct nand_chip *chip = mtd->priv; + int ret = 0; + uint32_t readlen = ops->len; + uint32_t oobreadlen = ops->ooblen; + uint32_t max_oobsize = ops->mode == MTD_OPS_AUTO_OOB ? + mtd->oobavail : mtd->oobsize; + + uint8_t *bufpoi, *oob, *buf; + int use_bufpoi; + unsigned int max_bitflips = 0; + int retry_mode = 0; + bool ecc_fail = false; + + chipnr = (int)(from >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + realpage = (int)(from >> chip->page_shift); + page = realpage & chip->pagemask; + + col = (int)(from & (mtd->writesize - 1)); + + buf = ops->datbuf; + oob = ops->oobbuf; + oob_required = oob ? 1 : 0; + + while (1) { + unsigned int ecc_failures = mtd->ecc_stats.failed; + + bytes = min(mtd->writesize - col, readlen); + aligned = (bytes == mtd->writesize); + + if (!aligned) + use_bufpoi = 1; + else if (chip->options & NAND_USE_BOUNCE_BUFFER) + use_bufpoi = !virt_addr_valid(buf); + else + use_bufpoi = 0; + + /* Is the current page in the buffer? */ + if (realpage != chip->pagebuf || oob) { + bufpoi = use_bufpoi ? chip->buffers->databuf : buf; + + if (use_bufpoi && aligned) + pr_debug("%s: using read bounce buffer for buf@%p\n", + __func__, buf); + +read_retry: + chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + + /* + * Now read the page into the buffer. Absent an error, + * the read methods return max bitflips per ecc step. + */ + if (unlikely(ops->mode == MTD_OPS_RAW)) + ret = chip->ecc.read_page_raw(mtd, chip, bufpoi, + oob_required, + page); + else if (!aligned && NAND_HAS_SUBPAGE_READ(chip) && + !oob) + ret = chip->ecc.read_subpage(mtd, chip, + col, bytes, bufpoi, + page); + else + ret = chip->ecc.read_page(mtd, chip, bufpoi, + oob_required, page); + if (ret < 0) { + if (use_bufpoi) + /* Invalidate page cache */ + chip->pagebuf = -1; + break; + } + + max_bitflips = max_t(unsigned int, max_bitflips, ret); + + /* Transfer not aligned data */ + if (use_bufpoi) { + if (!NAND_HAS_SUBPAGE_READ(chip) && !oob && + !(mtd->ecc_stats.failed - ecc_failures) && + (ops->mode != MTD_OPS_RAW)) { + chip->pagebuf = realpage; + chip->pagebuf_bitflips = ret; + } else { + /* Invalidate page cache */ + chip->pagebuf = -1; + } + memcpy(buf, chip->buffers->databuf + col, bytes); + } + + if (unlikely(oob)) { + int toread = min(oobreadlen, max_oobsize); + + if (toread) { + oob = nand_transfer_oob(chip, + oob, ops, toread); + oobreadlen -= toread; + } + } + + if (chip->options & NAND_NEED_READRDY) { + /* Apply delay or wait for ready/busy pin */ + if (!chip->dev_ready) + udelay(chip->chip_delay); + else + nand_wait_ready(mtd); + } + + if (mtd->ecc_stats.failed - ecc_failures) { + if (retry_mode + 1 < chip->read_retries) { + retry_mode++; + ret = nand_setup_read_retry(mtd, + retry_mode); + if (ret < 0) + break; + + /* Reset failures; retry */ + mtd->ecc_stats.failed = ecc_failures; + goto read_retry; + } else { + /* No more retry modes; real failure */ + ecc_fail = true; + } + } + + buf += bytes; + } else { + memcpy(buf, chip->buffers->databuf + col, bytes); + buf += bytes; + max_bitflips = max_t(unsigned int, max_bitflips, + chip->pagebuf_bitflips); + } + + readlen -= bytes; + + /* Reset to retry mode 0 */ + if (retry_mode) { + ret = nand_setup_read_retry(mtd, 0); + if (ret < 0) + break; + retry_mode = 0; + } + + if (!readlen) + break; + + /* For subsequent reads align to page boundary */ + col = 0; + /* Increment page address */ + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + } + chip->select_chip(mtd, -1); + + ops->retlen = ops->len - (size_t) readlen; + if (oob) + ops->oobretlen = ops->ooblen - oobreadlen; + + if (ret < 0) + return ret; + + if (ecc_fail) + return -EBADMSG; + + return max_bitflips; +} + +/** + * nand_read - [MTD Interface] MTD compatibility function for nand_do_read_ecc + * @mtd: MTD device structure + * @from: offset to read from + * @len: number of bytes to read + * @retlen: pointer to variable to store the number of read bytes + * @buf: the databuffer to put data + * + * Get hold of the chip and call nand_do_read. + */ +static int nand_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, uint8_t *buf) +{ + struct mtd_oob_ops ops; + int ret; + + nand_get_device(mtd, FL_READING); + memset(&ops, 0, sizeof(ops)); + ops.len = len; + ops.datbuf = buf; + ops.mode = MTD_OPS_PLACE_OOB; + ret = nand_do_read_ops(mtd, from, &ops); + *retlen = ops.retlen; + nand_release_device(mtd); + return ret; +} + +/** + * nand_read_oob_std - [REPLACEABLE] the most common OOB data read function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + */ +static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +/** + * nand_read_oob_syndrome - [REPLACEABLE] OOB data read function for HW ECC + * with syndromes + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to read + */ +static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + int length = mtd->oobsize; + int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; + int eccsize = chip->ecc.size; + uint8_t *bufpoi = chip->oob_poi; + int i, toread, sndrnd = 0, pos; + + chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page); + for (i = 0; i < chip->ecc.steps; i++) { + if (sndrnd) { + pos = eccsize + i * (eccsize + chunk); + if (mtd->writesize > 512) + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1); + else + chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page); + } else + sndrnd = 1; + toread = min_t(int, length, chunk); + chip->read_buf(mtd, bufpoi, toread); + bufpoi += toread; + length -= toread; + } + if (length > 0) + chip->read_buf(mtd, bufpoi, length); + + return 0; +} + +/** + * nand_write_oob_std - [REPLACEABLE] the most common OOB data write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to write + */ +static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + int status = 0; + const uint8_t *buf = chip->oob_poi; + int length = mtd->oobsize; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + chip->write_buf(mtd, buf, length); + /* Send command to program the OOB data */ + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/** + * nand_write_oob_syndrome - [REPLACEABLE] OOB data write function for HW ECC + * with syndrome - only for large page flash + * @mtd: mtd info structure + * @chip: nand chip info structure + * @page: page number to write + */ +static int nand_write_oob_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; + int eccsize = chip->ecc.size, length = mtd->oobsize; + int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps; + const uint8_t *bufpoi = chip->oob_poi; + + /* + * data-ecc-data-ecc ... ecc-oob + * or + * data-pad-ecc-pad-data-pad .... ecc-pad-oob + */ + if (!chip->ecc.prepad && !chip->ecc.postpad) { + pos = steps * (eccsize + chunk); + steps = 0; + } else + pos = eccsize; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page); + for (i = 0; i < steps; i++) { + if (sndcmd) { + if (mtd->writesize <= 512) { + uint32_t fill = 0xFFFFFFFF; + + len = eccsize; + while (len > 0) { + int num = min_t(int, len, 4); + chip->write_buf(mtd, (uint8_t *)&fill, + num); + len -= num; + } + } else { + pos = eccsize + i * (eccsize + chunk); + chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1); + } + } else + sndcmd = 1; + len = min_t(int, length, chunk); + chip->write_buf(mtd, bufpoi, len); + bufpoi += len; + length -= len; + } + if (length > 0) + chip->write_buf(mtd, bufpoi, length); + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + + return status & NAND_STATUS_FAIL ? -EIO : 0; +} + +/** + * nand_do_read_oob - [INTERN] NAND read out-of-band + * @mtd: MTD device structure + * @from: offset to read from + * @ops: oob operations description structure + * + * NAND read out-of-band data from the spare area. + */ +static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) +{ + int page, realpage, chipnr; + struct nand_chip *chip = mtd->priv; + struct mtd_ecc_stats stats; + int readlen = ops->ooblen; + int len; + uint8_t *buf = ops->oobbuf; + int ret = 0; + + pr_debug("%s: from = 0x%08Lx, len = %i\n", + __func__, (unsigned long long)from, readlen); + + stats = mtd->ecc_stats; + + if (ops->mode == MTD_OPS_AUTO_OOB) + len = chip->ecc.layout->oobavail; + else + len = mtd->oobsize; + + if (unlikely(ops->ooboffs >= len)) { + pr_debug("%s: attempt to start read outside oob\n", + __func__); + return -EINVAL; + } + + /* Do not allow reads past end of device */ + if (unlikely(from >= mtd->size || + ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) - + (from >> chip->page_shift)) * len)) { + pr_debug("%s: attempt to read beyond end of device\n", + __func__); + return -EINVAL; + } + + chipnr = (int)(from >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + /* Shift to get page */ + realpage = (int)(from >> chip->page_shift); + page = realpage & chip->pagemask; + + while (1) { + if (ops->mode == MTD_OPS_RAW) + ret = chip->ecc.read_oob_raw(mtd, chip, page); + else + ret = chip->ecc.read_oob(mtd, chip, page); + + if (ret < 0) + break; + + len = min(len, readlen); + buf = nand_transfer_oob(chip, buf, ops, len); + + if (chip->options & NAND_NEED_READRDY) { + /* Apply delay or wait for ready/busy pin */ + if (!chip->dev_ready) + udelay(chip->chip_delay); + else + nand_wait_ready(mtd); + } + + readlen -= len; + if (!readlen) + break; + + /* Increment page address */ + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + } + chip->select_chip(mtd, -1); + + ops->oobretlen = ops->ooblen - readlen; + + if (ret < 0) + return ret; + + if (mtd->ecc_stats.failed - stats.failed) + return -EBADMSG; + + return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0; +} + +/** + * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band + * @mtd: MTD device structure + * @from: offset to read from + * @ops: oob operation description structure + * + * NAND read data and/or out-of-band data. + */ +static int nand_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) +{ + int ret = -ENOTSUPP; + + ops->retlen = 0; + + /* Do not allow reads past end of device */ + if (ops->datbuf && (from + ops->len) > mtd->size) { + pr_debug("%s: attempt to read beyond end of device\n", + __func__); + return -EINVAL; + } + + nand_get_device(mtd, FL_READING); + + switch (ops->mode) { + case MTD_OPS_PLACE_OOB: + case MTD_OPS_AUTO_OOB: + case MTD_OPS_RAW: + break; + + default: + goto out; + } + + if (!ops->datbuf) + ret = nand_do_read_oob(mtd, from, ops); + else + ret = nand_do_read_ops(mtd, from, ops); + +out: + nand_release_device(mtd); + return ret; +} + + +/** + * nand_write_page_raw - [INTERN] raw page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * Not for syndrome calculating ECC controllers, which use a special oob layout. + */ +static int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + chip->write_buf(mtd, buf, mtd->writesize); + if (oob_required) + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +/** + * nand_write_page_raw_syndrome - [INTERN] raw page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * We need a special oob layout and handling even when ECC isn't checked. + */ +static int nand_write_page_raw_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + int eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + uint8_t *oob = chip->oob_poi; + int steps, size; + + for (steps = chip->ecc.steps; steps > 0; steps--) { + chip->write_buf(mtd, buf, eccsize); + buf += eccsize; + + if (chip->ecc.prepad) { + chip->write_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->write_buf(mtd, oob, eccbytes); + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->write_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; + } + } + + size = mtd->oobsize - (oob - chip->oob_poi); + if (size) + chip->write_buf(mtd, oob, size); + + return 0; +} +/** + * nand_write_page_swecc - [REPLACEABLE] software ECC based page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + */ +static int nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *ecc_calc = chip->buffers->ecccalc; + const uint8_t *p = buf; + uint32_t *eccpos = chip->ecc.layout->eccpos; + + /* Software ECC calculation */ + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + return chip->ecc.write_page_raw(mtd, chip, buf, 1); +} + +/** + * nand_write_page_hwecc - [REPLACEABLE] hardware ECC based page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + */ +static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + uint8_t *ecc_calc = chip->buffers->ecccalc; + const uint8_t *p = buf; + uint32_t *eccpos = chip->ecc.layout->eccpos; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + chip->write_buf(mtd, p, eccsize); + chip->ecc.calculate(mtd, p, &ecc_calc[i]); + } + + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + + +/** + * nand_write_subpage_hwecc - [REPLACEABLE] hardware ECC based subpage write + * @mtd: mtd info structure + * @chip: nand chip info structure + * @offset: column address of subpage within the page + * @data_len: data length + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + */ +static int nand_write_subpage_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint32_t offset, + uint32_t data_len, const uint8_t *buf, + int oob_required) +{ + uint8_t *oob_buf = chip->oob_poi; + uint8_t *ecc_calc = chip->buffers->ecccalc; + int ecc_size = chip->ecc.size; + int ecc_bytes = chip->ecc.bytes; + int ecc_steps = chip->ecc.steps; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint32_t start_step = offset / ecc_size; + uint32_t end_step = (offset + data_len - 1) / ecc_size; + int oob_bytes = mtd->oobsize / ecc_steps; + int step, i; + + for (step = 0; step < ecc_steps; step++) { + /* configure controller for WRITE access */ + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + + /* write data (untouched subpages already masked by 0xFF) */ + chip->write_buf(mtd, buf, ecc_size); + + /* mask ECC of un-touched subpages by padding 0xFF */ + if ((step < start_step) || (step > end_step)) + memset(ecc_calc, 0xff, ecc_bytes); + else + chip->ecc.calculate(mtd, buf, ecc_calc); + + /* mask OOB of un-touched subpages by padding 0xFF */ + /* if oob_required, preserve OOB metadata of written subpage */ + if (!oob_required || (step < start_step) || (step > end_step)) + memset(oob_buf, 0xff, oob_bytes); + + buf += ecc_size; + ecc_calc += ecc_bytes; + oob_buf += oob_bytes; + } + + /* copy calculated ECC for whole page to chip->buffer->oob */ + /* this include masked-value(0xFF) for unwritten subpages */ + ecc_calc = chip->buffers->ecccalc; + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + /* write OOB buffer to NAND device */ + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + + +/** + * nand_write_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page write + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * The hw generator calculates the error syndrome automatically. Therefore we + * need a special oob layout and handling. + */ +static int nand_write_page_syndrome(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + int i, eccsize = chip->ecc.size; + int eccbytes = chip->ecc.bytes; + int eccsteps = chip->ecc.steps; + const uint8_t *p = buf; + uint8_t *oob = chip->oob_poi; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + chip->write_buf(mtd, p, eccsize); + + if (chip->ecc.prepad) { + chip->write_buf(mtd, oob, chip->ecc.prepad); + oob += chip->ecc.prepad; + } + + chip->ecc.calculate(mtd, p, oob); + chip->write_buf(mtd, oob, eccbytes); + oob += eccbytes; + + if (chip->ecc.postpad) { + chip->write_buf(mtd, oob, chip->ecc.postpad); + oob += chip->ecc.postpad; + } + } + + /* Calculate remaining oob bytes */ + i = mtd->oobsize - (oob - chip->oob_poi); + if (i) + chip->write_buf(mtd, oob, i); + + return 0; +} + +/** + * nand_write_page - [REPLACEABLE] write one page + * @mtd: MTD device structure + * @chip: NAND chip descriptor + * @offset: address offset within the page + * @data_len: length of actual data to be written + * @buf: the data to write + * @oob_required: must write chip->oob_poi to OOB + * @page: page number to write + * @cached: cached programming + * @raw: use _raw version of write_page + */ +static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, int data_len, const uint8_t *buf, + int oob_required, int page, int cached, int raw) +{ + int status, subpage; + + if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && + chip->ecc.write_subpage) + subpage = offset || (data_len < mtd->writesize); + else + subpage = 0; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + + if (unlikely(raw)) + status = chip->ecc.write_page_raw(mtd, chip, buf, + oob_required); + else if (subpage) + status = chip->ecc.write_subpage(mtd, chip, offset, data_len, + buf, oob_required); + else + status = chip->ecc.write_page(mtd, chip, buf, oob_required); + + if (status < 0) + return status; + + /* + * Cached progamming disabled for now. Not sure if it's worth the + * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s). + */ + cached = 0; + + if (!cached || !NAND_HAS_CACHEPROG(chip)) { + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + /* + * See if operation failed and additional status checks are + * available. + */ + if ((status & NAND_STATUS_FAIL) && (chip->errstat)) + status = chip->errstat(mtd, chip, FL_WRITING, status, + page); + + if (status & NAND_STATUS_FAIL) + return -EIO; + } else { + chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + } + + return 0; +} + +/** + * nand_fill_oob - [INTERN] Transfer client buffer to oob + * @mtd: MTD device structure + * @oob: oob data buffer + * @len: oob data write length + * @ops: oob ops structure + */ +static uint8_t *nand_fill_oob(struct mtd_info *mtd, uint8_t *oob, size_t len, + struct mtd_oob_ops *ops) +{ + struct nand_chip *chip = mtd->priv; + + /* + * Initialise to all 0xFF, to avoid the possibility of left over OOB + * data from a previous OOB read. + */ + memset(chip->oob_poi, 0xff, mtd->oobsize); + + switch (ops->mode) { + + case MTD_OPS_PLACE_OOB: + case MTD_OPS_RAW: + memcpy(chip->oob_poi + ops->ooboffs, oob, len); + return oob + len; + + case MTD_OPS_AUTO_OOB: { + struct nand_oobfree *free = chip->ecc.layout->oobfree; + uint32_t boffs = 0, woffs = ops->ooboffs; + size_t bytes = 0; + + for (; free->length && len; free++, len -= bytes) { + /* Write request not from offset 0? */ + if (unlikely(woffs)) { + if (woffs >= free->length) { + woffs -= free->length; + continue; + } + boffs = free->offset + woffs; + bytes = min_t(size_t, len, + (free->length - woffs)); + woffs = 0; + } else { + bytes = min_t(size_t, len, free->length); + boffs = free->offset; + } + memcpy(chip->oob_poi + boffs, oob, bytes); + oob += bytes; + } + return oob; + } + default: + BUG(); + } + return NULL; +} + +#define NOTALIGNED(x) ((x & (chip->subpagesize - 1)) != 0) + +/** + * nand_do_write_ops - [INTERN] NAND write with ECC + * @mtd: MTD device structure + * @to: offset to write to + * @ops: oob operations description structure + * + * NAND write with ECC. + */ +static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) +{ + int chipnr, realpage, page, blockmask, column; + struct nand_chip *chip = mtd->priv; + uint32_t writelen = ops->len; + + uint32_t oobwritelen = ops->ooblen; + uint32_t oobmaxlen = ops->mode == MTD_OPS_AUTO_OOB ? + mtd->oobavail : mtd->oobsize; + + uint8_t *oob = ops->oobbuf; + uint8_t *buf = ops->datbuf; + int ret; + int oob_required = oob ? 1 : 0; + + ops->retlen = 0; + if (!writelen) + return 0; + + /* Reject writes, which are not page aligned */ + if (NOTALIGNED(to) || NOTALIGNED(ops->len)) { + pr_notice("%s: attempt to write non page aligned data\n", + __func__); + return -EINVAL; + } + + column = to & (mtd->writesize - 1); + + chipnr = (int)(to >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) { + ret = -EIO; + goto err_out; + } + + realpage = (int)(to >> chip->page_shift); + page = realpage & chip->pagemask; + blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; + + /* Invalidate the page cache, when we write to the cached page */ + if (to <= ((loff_t)chip->pagebuf << chip->page_shift) && + ((loff_t)chip->pagebuf << chip->page_shift) < (to + ops->len)) + chip->pagebuf = -1; + + /* Don't allow multipage oob writes with offset */ + if (oob && ops->ooboffs && (ops->ooboffs + ops->ooblen > oobmaxlen)) { + ret = -EINVAL; + goto err_out; + } + + while (1) { + int bytes = mtd->writesize; + int cached = writelen > bytes && page != blockmask; + uint8_t *wbuf = buf; + int use_bufpoi; + int part_pagewr = (column || writelen < (mtd->writesize - 1)); + + if (part_pagewr) + use_bufpoi = 1; + else if (chip->options & NAND_USE_BOUNCE_BUFFER) + use_bufpoi = !virt_addr_valid(buf); + else + use_bufpoi = 0; + + /* Partial page write?, or need to use bounce buffer */ + if (use_bufpoi) { + pr_debug("%s: using write bounce buffer for buf@%p\n", + __func__, buf); + cached = 0; + if (part_pagewr) + bytes = min_t(int, bytes - column, writelen); + chip->pagebuf = -1; + memset(chip->buffers->databuf, 0xff, mtd->writesize); + memcpy(&chip->buffers->databuf[column], buf, bytes); + wbuf = chip->buffers->databuf; + } + + if (unlikely(oob)) { + size_t len = min(oobwritelen, oobmaxlen); + oob = nand_fill_oob(mtd, oob, len, ops); + oobwritelen -= len; + } else { + /* We still need to erase leftover OOB data */ + memset(chip->oob_poi, 0xff, mtd->oobsize); + } + ret = chip->write_page(mtd, chip, column, bytes, wbuf, + oob_required, page, cached, + (ops->mode == MTD_OPS_RAW)); + if (ret) + break; + + writelen -= bytes; + if (!writelen) + break; + + column = 0; + buf += bytes; + realpage++; + + page = realpage & chip->pagemask; + /* Check, if we cross a chip boundary */ + if (!page) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + } + + ops->retlen = ops->len - writelen; + if (unlikely(oob)) + ops->oobretlen = ops->ooblen; + +err_out: + chip->select_chip(mtd, -1); + return ret; +} + +/** + * panic_nand_write - [MTD Interface] NAND write with ECC + * @mtd: MTD device structure + * @to: offset to write to + * @len: number of bytes to write + * @retlen: pointer to variable to store the number of written bytes + * @buf: the data to write + * + * NAND write with ECC. Used when performing writes in interrupt context, this + * may for example be called by mtdoops when writing an oops while in panic. + */ +static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const uint8_t *buf) +{ + struct nand_chip *chip = mtd->priv; + struct mtd_oob_ops ops; + int ret; + + /* Wait for the device to get ready */ + panic_nand_wait(mtd, chip, 400); + + /* Grab the device */ + panic_nand_get_device(chip, mtd, FL_WRITING); + + memset(&ops, 0, sizeof(ops)); + ops.len = len; + ops.datbuf = (uint8_t *)buf; + ops.mode = MTD_OPS_PLACE_OOB; + + ret = nand_do_write_ops(mtd, to, &ops); + + *retlen = ops.retlen; + return ret; +} + +/** + * nand_write - [MTD Interface] NAND write with ECC + * @mtd: MTD device structure + * @to: offset to write to + * @len: number of bytes to write + * @retlen: pointer to variable to store the number of written bytes + * @buf: the data to write + * + * NAND write with ECC. + */ +static int nand_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const uint8_t *buf) +{ + struct mtd_oob_ops ops; + int ret; + + nand_get_device(mtd, FL_WRITING); + memset(&ops, 0, sizeof(ops)); + ops.len = len; + ops.datbuf = (uint8_t *)buf; + ops.mode = MTD_OPS_PLACE_OOB; + ret = nand_do_write_ops(mtd, to, &ops); + *retlen = ops.retlen; + nand_release_device(mtd); + return ret; +} + +/** + * nand_do_write_oob - [MTD Interface] NAND write out-of-band + * @mtd: MTD device structure + * @to: offset to write to + * @ops: oob operation description structure + * + * NAND write out-of-band. + */ +static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) +{ + int chipnr, page, status, len; + struct nand_chip *chip = mtd->priv; + + pr_debug("%s: to = 0x%08x, len = %i\n", + __func__, (unsigned int)to, (int)ops->ooblen); + + if (ops->mode == MTD_OPS_AUTO_OOB) + len = chip->ecc.layout->oobavail; + else + len = mtd->oobsize; + + /* Do not allow write past end of page */ + if ((ops->ooboffs + ops->ooblen) > len) { + pr_debug("%s: attempt to write past end of page\n", + __func__); + return -EINVAL; + } + + if (unlikely(ops->ooboffs >= len)) { + pr_debug("%s: attempt to start write outside oob\n", + __func__); + return -EINVAL; + } + + /* Do not allow write past end of device */ + if (unlikely(to >= mtd->size || + ops->ooboffs + ops->ooblen > + ((mtd->size >> chip->page_shift) - + (to >> chip->page_shift)) * len)) { + pr_debug("%s: attempt to write beyond end of device\n", + __func__); + return -EINVAL; + } + + chipnr = (int)(to >> chip->chip_shift); + chip->select_chip(mtd, chipnr); + + /* Shift to get page */ + page = (int)(to >> chip->page_shift); + + /* + * Reset the chip. Some chips (like the Toshiba TC5832DC found in one + * of my DiskOnChip 2000 test units) will clear the whole data page too + * if we don't do this. I have no clue why, but I seem to have 'fixed' + * it in the doc2000 driver in August 1999. dwmw2. + */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) { + chip->select_chip(mtd, -1); + return -EROFS; + } + + /* Invalidate the page cache, if we write to the cached page */ + if (page == chip->pagebuf) + chip->pagebuf = -1; + + nand_fill_oob(mtd, ops->oobbuf, ops->ooblen, ops); + + if (ops->mode == MTD_OPS_RAW) + status = chip->ecc.write_oob_raw(mtd, chip, page & chip->pagemask); + else + status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask); + + chip->select_chip(mtd, -1); + + if (status) + return status; + + ops->oobretlen = ops->ooblen; + + return 0; +} + +/** + * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band + * @mtd: MTD device structure + * @to: offset to write to + * @ops: oob operation description structure + */ +static int nand_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) +{ + int ret = -ENOTSUPP; + + ops->retlen = 0; + + /* Do not allow writes past end of device */ + if (ops->datbuf && (to + ops->len) > mtd->size) { + pr_debug("%s: attempt to write beyond end of device\n", + __func__); + return -EINVAL; + } + + nand_get_device(mtd, FL_WRITING); + + switch (ops->mode) { + case MTD_OPS_PLACE_OOB: + case MTD_OPS_AUTO_OOB: + case MTD_OPS_RAW: + break; + + default: + goto out; + } + + if (!ops->datbuf) + ret = nand_do_write_oob(mtd, to, ops); + else + ret = nand_do_write_ops(mtd, to, ops); + +out: + nand_release_device(mtd); + return ret; +} + +/** + * single_erase - [GENERIC] NAND standard block erase command function + * @mtd: MTD device structure + * @page: the page address of the block which will be erased + * + * Standard erase command for NAND chips. Returns NAND status. + */ +static int single_erase(struct mtd_info *mtd, int page) +{ + struct nand_chip *chip = mtd->priv; + /* Send commands to erase a block */ + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + + return chip->waitfunc(mtd, chip); +} + +/** + * nand_erase - [MTD Interface] erase block(s) + * @mtd: MTD device structure + * @instr: erase instruction + * + * Erase one ore more blocks. + */ +static int nand_erase(struct mtd_info *mtd, struct erase_info *instr) +{ + return nand_erase_nand(mtd, instr, 0); +} + +/** + * nand_erase_nand - [INTERN] erase block(s) + * @mtd: MTD device structure + * @instr: erase instruction + * @allowbbt: allow erasing the bbt area + * + * Erase one ore more blocks. + */ +int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, + int allowbbt) +{ + int page, status, pages_per_block, ret, chipnr; + struct nand_chip *chip = mtd->priv; + loff_t len; + + pr_debug("%s: start = 0x%012llx, len = %llu\n", + __func__, (unsigned long long)instr->addr, + (unsigned long long)instr->len); + + if (check_offs_len(mtd, instr->addr, instr->len)) + return -EINVAL; + + /* Grab the lock and see if the device is available */ + nand_get_device(mtd, FL_ERASING); + + /* Shift to get first page */ + page = (int)(instr->addr >> chip->page_shift); + chipnr = (int)(instr->addr >> chip->chip_shift); + + /* Calculate pages in each block */ + pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); + + /* Select the NAND device */ + chip->select_chip(mtd, chipnr); + + /* Check, if it is write protected */ + if (nand_check_wp(mtd)) { + pr_debug("%s: device is write protected!\n", + __func__); + instr->state = MTD_ERASE_FAILED; + goto erase_exit; + } + + /* Loop through the pages */ + len = instr->len; + + instr->state = MTD_ERASING; + + while (len) { + /* Check if we have a bad block, we do not erase bad blocks! */ + if (nand_block_checkbad(mtd, ((loff_t) page) << + chip->page_shift, 0, allowbbt)) { + pr_warn("%s: attempt to erase a bad block at page 0x%08x\n", + __func__, page); + instr->state = MTD_ERASE_FAILED; + goto erase_exit; + } + + /* + * Invalidate the page cache, if we erase the block which + * contains the current cached page. + */ + if (page <= chip->pagebuf && chip->pagebuf < + (page + pages_per_block)) + chip->pagebuf = -1; + + status = chip->erase(mtd, page & chip->pagemask); + + /* + * See if operation failed and additional status checks are + * available + */ + if ((status & NAND_STATUS_FAIL) && (chip->errstat)) + status = chip->errstat(mtd, chip, FL_ERASING, + status, page); + + /* See if block erase succeeded */ + if (status & NAND_STATUS_FAIL) { + pr_debug("%s: failed erase, page 0x%08x\n", + __func__, page); + instr->state = MTD_ERASE_FAILED; + instr->fail_addr = + ((loff_t)page << chip->page_shift); + goto erase_exit; + } + + /* Increment page address and decrement length */ + len -= (1ULL << chip->phys_erase_shift); + page += pages_per_block; + + /* Check, if we cross a chip boundary */ + if (len && !(page & chip->pagemask)) { + chipnr++; + chip->select_chip(mtd, -1); + chip->select_chip(mtd, chipnr); + } + } + instr->state = MTD_ERASE_DONE; + +erase_exit: + + ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO; + + /* Deselect and wake up anyone waiting on the device */ + chip->select_chip(mtd, -1); + nand_release_device(mtd); + + /* Do call back function */ + if (!ret) + mtd_erase_callback(instr); + + /* Return more or less happy */ + return ret; +} + +/** + * nand_sync - [MTD Interface] sync + * @mtd: MTD device structure + * + * Sync is actually a wait for chip ready function. + */ +static void nand_sync(struct mtd_info *mtd) +{ + pr_debug("%s: called\n", __func__); + + /* Grab the lock and see if the device is available */ + nand_get_device(mtd, FL_SYNCING); + /* Release it and go back */ + nand_release_device(mtd); +} + +/** + * nand_block_isbad - [MTD Interface] Check if block at offset is bad + * @mtd: MTD device structure + * @offs: offset relative to mtd start + */ +static int nand_block_isbad(struct mtd_info *mtd, loff_t offs) +{ + return nand_block_checkbad(mtd, offs, 1, 0); +} + +/** + * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad + * @mtd: MTD device structure + * @ofs: offset relative to mtd start + */ +static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + int ret; + + ret = nand_block_isbad(mtd, ofs); + if (ret) { + /* If it was bad already, return success and do nothing */ + if (ret > 0) + return 0; + return ret; + } + + return nand_block_markbad_lowlevel(mtd, ofs); +} + +/** + * nand_onfi_set_features- [REPLACEABLE] set features for ONFI nand + * @mtd: MTD device structure + * @chip: nand chip info structure + * @addr: feature address. + * @subfeature_param: the subfeature parameters, a four bytes array. + */ +static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, + int addr, uint8_t *subfeature_param) +{ + int status; + int i; + + if (!chip->onfi_version || + !(le16_to_cpu(chip->onfi_params.opt_cmd) + & ONFI_OPT_CMD_SET_GET_FEATURES)) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + chip->write_byte(mtd, subfeature_param[i]); + + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + return -EIO; + return 0; +} + +/** + * nand_onfi_get_features- [REPLACEABLE] get features for ONFI nand + * @mtd: MTD device structure + * @chip: nand chip info structure + * @addr: feature address. + * @subfeature_param: the subfeature parameters, a four bytes array. + */ +static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, + int addr, uint8_t *subfeature_param) +{ + int i; + + if (!chip->onfi_version || + !(le16_to_cpu(chip->onfi_params.opt_cmd) + & ONFI_OPT_CMD_SET_GET_FEATURES)) + return -EINVAL; + + /* clear the sub feature parameters */ + memset(subfeature_param, 0, ONFI_SUBFEATURE_PARAM_LEN); + + chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + *subfeature_param++ = chip->read_byte(mtd); + return 0; +} + +/** + * nand_suspend - [MTD Interface] Suspend the NAND flash + * @mtd: MTD device structure + */ +static int nand_suspend(struct mtd_info *mtd) +{ + return nand_get_device(mtd, FL_PM_SUSPENDED); +} + +/** + * nand_resume - [MTD Interface] Resume the NAND flash + * @mtd: MTD device structure + */ +static void nand_resume(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + + if (chip->state == FL_PM_SUSPENDED) + nand_release_device(mtd); + else + pr_err("%s called for a chip which is not in suspended state\n", + __func__); +} + +/** + * nand_shutdown - [MTD Interface] Finish the current NAND operation and + * prevent further operations + * @mtd: MTD device structure + */ +static void nand_shutdown(struct mtd_info *mtd) +{ + nand_get_device(mtd, FL_SHUTDOWN); +} + +/* Set default functions */ +static void nand_set_defaults(struct nand_chip *chip, int busw) +{ + /* check for proper chip_delay setup, set 20us if not */ + if (!chip->chip_delay) + chip->chip_delay = 20; + + /* check, if a user supplied command function given */ + if (chip->cmdfunc == NULL) + chip->cmdfunc = nand_command; + + /* check, if a user supplied wait function given */ + if (chip->waitfunc == NULL) + chip->waitfunc = nand_wait; + + if (!chip->select_chip) + chip->select_chip = nand_select_chip; + + /* set for ONFI nand */ + if (!chip->onfi_set_features) + chip->onfi_set_features = nand_onfi_set_features; + if (!chip->onfi_get_features) + chip->onfi_get_features = nand_onfi_get_features; + + /* If called twice, pointers that depend on busw may need to be reset */ + if (!chip->read_byte || chip->read_byte == nand_read_byte) + chip->read_byte = busw ? nand_read_byte16 : nand_read_byte; + if (!chip->read_word) + chip->read_word = nand_read_word; + if (!chip->block_bad) + chip->block_bad = nand_block_bad; + if (!chip->block_markbad) + chip->block_markbad = nand_default_block_markbad; + if (!chip->write_buf || chip->write_buf == nand_write_buf) + chip->write_buf = busw ? nand_write_buf16 : nand_write_buf; + if (!chip->write_byte || chip->write_byte == nand_write_byte) + chip->write_byte = busw ? nand_write_byte16 : nand_write_byte; + if (!chip->read_buf || chip->read_buf == nand_read_buf) + chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; + if (!chip->scan_bbt) + chip->scan_bbt = nand_default_bbt; + + if (!chip->controller) { + chip->controller = &chip->hwcontrol; + spin_lock_init(&chip->controller->lock); + init_waitqueue_head(&chip->controller->wq); + } + +} + +/* Sanitize ONFI strings so we can safely print them */ +static void sanitize_string(uint8_t *s, size_t len) +{ + ssize_t i; + + /* Null terminate */ + s[len - 1] = 0; + + /* Remove non printable chars */ + for (i = 0; i < len - 1; i++) { + if (s[i] < ' ' || s[i] > 127) + s[i] = '?'; + } + + /* Remove trailing spaces */ + strim(s); +} + +static u16 onfi_crc16(u16 crc, u8 const *p, size_t len) +{ + int i; + while (len--) { + crc ^= *p++ << 8; + for (i = 0; i < 8; i++) + crc = (crc << 1) ^ ((crc & 0x8000) ? 0x8005 : 0); + } + + return crc; +} + +/* Parse the Extended Parameter Page. */ +static int nand_flash_detect_ext_param_page(struct mtd_info *mtd, + struct nand_chip *chip, struct nand_onfi_params *p) +{ + struct onfi_ext_param_page *ep; + struct onfi_ext_section *s; + struct onfi_ext_ecc_info *ecc; + uint8_t *cursor; + int ret = -EINVAL; + int len; + int i; + + len = le16_to_cpu(p->ext_param_page_length) * 16; + ep = kmalloc(len, GFP_KERNEL); + if (!ep) + return -ENOMEM; + + /* Send our own NAND_CMD_PARAM. */ + chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); + + /* Use the Change Read Column command to skip the ONFI param pages. */ + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, + sizeof(*p) * p->num_of_param_pages , -1); + + /* Read out the Extended Parameter Page. */ + chip->read_buf(mtd, (uint8_t *)ep, len); + if ((onfi_crc16(ONFI_CRC_BASE, ((uint8_t *)ep) + 2, len - 2) + != le16_to_cpu(ep->crc))) { + pr_debug("fail in the CRC.\n"); + goto ext_out; + } + + /* + * Check the signature. + * Do not strictly follow the ONFI spec, maybe changed in future. + */ + if (strncmp(ep->sig, "EPPS", 4)) { + pr_debug("The signature is invalid.\n"); + goto ext_out; + } + + /* find the ECC section. */ + cursor = (uint8_t *)(ep + 1); + for (i = 0; i < ONFI_EXT_SECTION_MAX; i++) { + s = ep->sections + i; + if (s->type == ONFI_SECTION_TYPE_2) + break; + cursor += s->length * 16; + } + if (i == ONFI_EXT_SECTION_MAX) { + pr_debug("We can not find the ECC section.\n"); + goto ext_out; + } + + /* get the info we want. */ + ecc = (struct onfi_ext_ecc_info *)cursor; + + if (!ecc->codeword_size) { + pr_debug("Invalid codeword size\n"); + goto ext_out; + } + + chip->ecc_strength_ds = ecc->ecc_bits; + chip->ecc_step_ds = 1 << ecc->codeword_size; + ret = 0; + +ext_out: + kfree(ep); + return ret; +} + +static int nand_setup_read_retry_micron(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {retry_mode}; + + return chip->onfi_set_features(mtd, chip, ONFI_FEATURE_ADDR_READ_RETRY, + feature); +} + +/* + * Configure chip properties from Micron vendor-specific ONFI table + */ +static void nand_onfi_detect_micron(struct nand_chip *chip, + struct nand_onfi_params *p) +{ + struct nand_onfi_vendor_micron *micron = (void *)p->vendor; + + if (le16_to_cpu(p->vendor_revision) < 1) + return; + + chip->read_retries = micron->read_retry_options; + chip->setup_read_retry = nand_setup_read_retry_micron; +} + +/* + * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise. + */ +static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, + int *busw) +{ + struct nand_onfi_params *p = &chip->onfi_params; + int i, j; + int val; + + /* Try ONFI for unknown chip or LP */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1); + if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' || + chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I') + return 0; + + chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); + for (i = 0; i < 3; i++) { + for (j = 0; j < sizeof(*p); j++) + ((uint8_t *)p)[j] = chip->read_byte(mtd); + if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) == + le16_to_cpu(p->crc)) { + break; + } + } + + if (i == 3) { + pr_err("Could not find valid ONFI parameter page; aborting\n"); + return 0; + } + + /* Check version */ + val = le16_to_cpu(p->revision); + if (val & (1 << 5)) + chip->onfi_version = 23; + else if (val & (1 << 4)) + chip->onfi_version = 22; + else if (val & (1 << 3)) + chip->onfi_version = 21; + else if (val & (1 << 2)) + chip->onfi_version = 20; + else if (val & (1 << 1)) + chip->onfi_version = 10; + + if (!chip->onfi_version) { + pr_info("unsupported ONFI version: %d\n", val); + return 0; + } + + sanitize_string(p->manufacturer, sizeof(p->manufacturer)); + sanitize_string(p->model, sizeof(p->model)); + if (!mtd->name) + mtd->name = p->model; + + mtd->writesize = le32_to_cpu(p->byte_per_page); + + /* + * pages_per_block and blocks_per_lun may not be a power-of-2 size + * (don't ask me who thought of this...). MTD assumes that these + * dimensions will be power-of-2, so just truncate the remaining area. + */ + mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1); + mtd->erasesize *= mtd->writesize; + + mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page); + + /* See erasesize comment */ + chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1); + chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count; + chip->bits_per_cell = p->bits_per_cell; + + if (onfi_feature(chip) & ONFI_FEATURE_16_BIT_BUS) + *busw = NAND_BUSWIDTH_16; + else + *busw = 0; + + if (p->ecc_bits != 0xff) { + chip->ecc_strength_ds = p->ecc_bits; + chip->ecc_step_ds = 512; + } else if (chip->onfi_version >= 21 && + (onfi_feature(chip) & ONFI_FEATURE_EXT_PARAM_PAGE)) { + + /* + * The nand_flash_detect_ext_param_page() uses the + * Change Read Column command which maybe not supported + * by the chip->cmdfunc. So try to update the chip->cmdfunc + * now. We do not replace user supplied command function. + */ + if (mtd->writesize > 512 && chip->cmdfunc == nand_command) + chip->cmdfunc = nand_command_lp; + + /* The Extended Parameter Page is supported since ONFI 2.1. */ + if (nand_flash_detect_ext_param_page(mtd, chip, p)) + pr_warn("Failed to detect ONFI extended param page\n"); + } else { + pr_warn("Could not retrieve ONFI ECC requirements\n"); + } + + if (p->jedec_id == NAND_MFR_MICRON) + nand_onfi_detect_micron(chip, p); + + return 1; +} + +/* + * Check if the NAND chip is JEDEC compliant, returns 1 if it is, 0 otherwise. + */ +static int nand_flash_detect_jedec(struct mtd_info *mtd, struct nand_chip *chip, + int *busw) +{ + struct nand_jedec_params *p = &chip->jedec_params; + struct jedec_ecc_info *ecc; + int val; + int i, j; + + /* Try JEDEC for unknown chip or LP */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x40, -1); + if (chip->read_byte(mtd) != 'J' || chip->read_byte(mtd) != 'E' || + chip->read_byte(mtd) != 'D' || chip->read_byte(mtd) != 'E' || + chip->read_byte(mtd) != 'C') + return 0; + + chip->cmdfunc(mtd, NAND_CMD_PARAM, 0x40, -1); + for (i = 0; i < 3; i++) { + for (j = 0; j < sizeof(*p); j++) + ((uint8_t *)p)[j] = chip->read_byte(mtd); + + if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 510) == + le16_to_cpu(p->crc)) + break; + } + + if (i == 3) { + pr_err("Could not find valid JEDEC parameter page; aborting\n"); + return 0; + } + + /* Check version */ + val = le16_to_cpu(p->revision); + if (val & (1 << 2)) + chip->jedec_version = 10; + else if (val & (1 << 1)) + chip->jedec_version = 1; /* vendor specific version */ + + if (!chip->jedec_version) { + pr_info("unsupported JEDEC version: %d\n", val); + return 0; + } + + sanitize_string(p->manufacturer, sizeof(p->manufacturer)); + sanitize_string(p->model, sizeof(p->model)); + if (!mtd->name) + mtd->name = p->model; + + mtd->writesize = le32_to_cpu(p->byte_per_page); + + /* Please reference to the comment for nand_flash_detect_onfi. */ + mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1); + mtd->erasesize *= mtd->writesize; + + mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page); + + /* Please reference to the comment for nand_flash_detect_onfi. */ + chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1); + chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count; + chip->bits_per_cell = p->bits_per_cell; + + if (jedec_feature(chip) & JEDEC_FEATURE_16_BIT_BUS) + *busw = NAND_BUSWIDTH_16; + else + *busw = 0; + + /* ECC info */ + ecc = &p->ecc_info[0]; + + if (ecc->codeword_size >= 9) { + chip->ecc_strength_ds = ecc->ecc_bits; + chip->ecc_step_ds = 1 << ecc->codeword_size; + } else { + pr_warn("Invalid codeword size\n"); + } + + return 1; +} + +/* + * nand_id_has_period - Check if an ID string has a given wraparound period + * @id_data: the ID string + * @arrlen: the length of the @id_data array + * @period: the period of repitition + * + * Check if an ID string is repeated within a given sequence of bytes at + * specific repetition interval period (e.g., {0x20,0x01,0x7F,0x20} has a + * period of 3). This is a helper function for nand_id_len(). Returns non-zero + * if the repetition has a period of @period; otherwise, returns zero. + */ +static int nand_id_has_period(u8 *id_data, int arrlen, int period) +{ + int i, j; + for (i = 0; i < period; i++) + for (j = i + period; j < arrlen; j += period) + if (id_data[i] != id_data[j]) + return 0; + return 1; +} + +/* + * nand_id_len - Get the length of an ID string returned by CMD_READID + * @id_data: the ID string + * @arrlen: the length of the @id_data array + + * Returns the length of the ID string, according to known wraparound/trailing + * zero patterns. If no pattern exists, returns the length of the array. + */ +static int nand_id_len(u8 *id_data, int arrlen) +{ + int last_nonzero, period; + + /* Find last non-zero byte */ + for (last_nonzero = arrlen - 1; last_nonzero >= 0; last_nonzero--) + if (id_data[last_nonzero]) + break; + + /* All zeros */ + if (last_nonzero < 0) + return 0; + + /* Calculate wraparound period */ + for (period = 1; period < arrlen; period++) + if (nand_id_has_period(id_data, arrlen, period)) + break; + + /* There's a repeated pattern */ + if (period < arrlen) + return period; + + /* There are trailing zeros */ + if (last_nonzero < arrlen - 1) + return last_nonzero + 1; + + /* No pattern detected */ + return arrlen; +} + +/* Extract the bits of per cell from the 3rd byte of the extended ID */ +static int nand_get_bits_per_cell(u8 cellinfo) +{ + int bits; + + bits = cellinfo & NAND_CI_CELLTYPE_MSK; + bits >>= NAND_CI_CELLTYPE_SHIFT; + return bits + 1; +} + +/* + * Many new NAND share similar device ID codes, which represent the size of the + * chip. The rest of the parameters must be decoded according to generic or + * manufacturer-specific "extended ID" decoding patterns. + */ +static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, + u8 id_data[8], int *busw) +{ + int extid, id_len; + /* The 3rd id byte holds MLC / multichip data */ + chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]); + /* The 4th id byte is the important one */ + extid = id_data[3]; + + id_len = nand_id_len(id_data, 8); + + /* + * Field definitions are in the following datasheets: + * Old style (4,5 byte ID): Samsung K9GAG08U0M (p.32) + * New Samsung (6 byte ID): Samsung K9GAG08U0F (p.44) + * Hynix MLC (6 byte ID): Hynix H27UBG8T2B (p.22) + * + * Check for ID length, non-zero 6th byte, cell type, and Hynix/Samsung + * ID to decide what to do. + */ + if (id_len == 6 && id_data[0] == NAND_MFR_SAMSUNG && + !nand_is_slc(chip) && id_data[5] != 0x00) { + /* Calc pagesize */ + mtd->writesize = 2048 << (extid & 0x03); + extid >>= 2; + /* Calc oobsize */ + switch (((extid >> 2) & 0x04) | (extid & 0x03)) { + case 1: + mtd->oobsize = 128; + break; + case 2: + mtd->oobsize = 218; + break; + case 3: + mtd->oobsize = 400; + break; + case 4: + mtd->oobsize = 436; + break; + case 5: + mtd->oobsize = 512; + break; + case 6: + mtd->oobsize = 640; + break; + case 7: + default: /* Other cases are "reserved" (unknown) */ + mtd->oobsize = 1024; + break; + } + extid >>= 2; + /* Calc blocksize */ + mtd->erasesize = (128 * 1024) << + (((extid >> 1) & 0x04) | (extid & 0x03)); + *busw = 0; + } else if (id_len == 6 && id_data[0] == NAND_MFR_HYNIX && + !nand_is_slc(chip)) { + unsigned int tmp; + + /* Calc pagesize */ + mtd->writesize = 2048 << (extid & 0x03); + extid >>= 2; + /* Calc oobsize */ + switch (((extid >> 2) & 0x04) | (extid & 0x03)) { + case 0: + mtd->oobsize = 128; + break; + case 1: + mtd->oobsize = 224; + break; + case 2: + mtd->oobsize = 448; + break; + case 3: + mtd->oobsize = 64; + break; + case 4: + mtd->oobsize = 32; + break; + case 5: + mtd->oobsize = 16; + break; + default: + mtd->oobsize = 640; + break; + } + extid >>= 2; + /* Calc blocksize */ + tmp = ((extid >> 1) & 0x04) | (extid & 0x03); + if (tmp < 0x03) + mtd->erasesize = (128 * 1024) << tmp; + else if (tmp == 0x03) + mtd->erasesize = 768 * 1024; + else + mtd->erasesize = (64 * 1024) << tmp; + *busw = 0; + } else { + /* Calc pagesize */ + mtd->writesize = 1024 << (extid & 0x03); + extid >>= 2; + /* Calc oobsize */ + mtd->oobsize = (8 << (extid & 0x01)) * + (mtd->writesize >> 9); + extid >>= 2; + /* Calc blocksize. Blocksize is multiples of 64KiB */ + mtd->erasesize = (64 * 1024) << (extid & 0x03); + extid >>= 2; + /* Get buswidth information */ + *busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0; + + /* + * Toshiba 24nm raw SLC (i.e., not BENAND) have 32B OOB per + * 512B page. For Toshiba SLC, we decode the 5th/6th byte as + * follows: + * - ID byte 6, bits[2:0]: 100b -> 43nm, 101b -> 32nm, + * 110b -> 24nm + * - ID byte 5, bit[7]: 1 -> BENAND, 0 -> raw SLC + */ + if (id_len >= 6 && id_data[0] == NAND_MFR_TOSHIBA && + nand_is_slc(chip) && + (id_data[5] & 0x7) == 0x6 /* 24nm */ && + !(id_data[4] & 0x80) /* !BENAND */) { + mtd->oobsize = 32 * mtd->writesize >> 9; + } + + } +} + +/* + * Old devices have chip data hardcoded in the device ID table. nand_decode_id + * decodes a matching ID table entry and assigns the MTD size parameters for + * the chip. + */ +static void nand_decode_id(struct mtd_info *mtd, struct nand_chip *chip, + struct nand_flash_dev *type, u8 id_data[8], + int *busw) +{ + int maf_id = id_data[0]; + + mtd->erasesize = type->erasesize; + mtd->writesize = type->pagesize; + mtd->oobsize = mtd->writesize / 32; + *busw = type->options & NAND_BUSWIDTH_16; + + /* All legacy ID NAND are small-page, SLC */ + chip->bits_per_cell = 1; + + /* + * Check for Spansion/AMD ID + repeating 5th, 6th byte since + * some Spansion chips have erasesize that conflicts with size + * listed in nand_ids table. + * Data sheet (5 byte ID): Spansion S30ML-P ORNAND (p.39) + */ + if (maf_id == NAND_MFR_AMD && id_data[4] != 0x00 && id_data[5] == 0x00 + && id_data[6] == 0x00 && id_data[7] == 0x00 + && mtd->writesize == 512) { + mtd->erasesize = 128 * 1024; + mtd->erasesize <<= ((id_data[3] & 0x03) << 1); + } +} + +/* + * Set the bad block marker/indicator (BBM/BBI) patterns according to some + * heuristic patterns using various detected parameters (e.g., manufacturer, + * page size, cell-type information). + */ +static void nand_decode_bbm_options(struct mtd_info *mtd, + struct nand_chip *chip, u8 id_data[8]) +{ + int maf_id = id_data[0]; + + /* Set the bad block position */ + if (mtd->writesize > 512 || (chip->options & NAND_BUSWIDTH_16)) + chip->badblockpos = NAND_LARGE_BADBLOCK_POS; + else + chip->badblockpos = NAND_SMALL_BADBLOCK_POS; + + /* + * Bad block marker is stored in the last page of each block on Samsung + * and Hynix MLC devices; stored in first two pages of each block on + * Micron devices with 2KiB pages and on SLC Samsung, Hynix, Toshiba, + * AMD/Spansion, and Macronix. All others scan only the first page. + */ + if (!nand_is_slc(chip) && + (maf_id == NAND_MFR_SAMSUNG || + maf_id == NAND_MFR_HYNIX)) + chip->bbt_options |= NAND_BBT_SCANLASTPAGE; + else if ((nand_is_slc(chip) && + (maf_id == NAND_MFR_SAMSUNG || + maf_id == NAND_MFR_HYNIX || + maf_id == NAND_MFR_TOSHIBA || + maf_id == NAND_MFR_AMD || + maf_id == NAND_MFR_MACRONIX)) || + (mtd->writesize == 2048 && + maf_id == NAND_MFR_MICRON)) + chip->bbt_options |= NAND_BBT_SCAN2NDPAGE; +} + +static inline bool is_full_id_nand(struct nand_flash_dev *type) +{ + return type->id_len; +} + +static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip, + struct nand_flash_dev *type, u8 *id_data, int *busw) +{ + if (!strncmp(type->id, id_data, type->id_len)) { + mtd->writesize = type->pagesize; + mtd->erasesize = type->erasesize; + mtd->oobsize = type->oobsize; + + chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]); + chip->chipsize = (uint64_t)type->chipsize << 20; + chip->options |= type->options; + chip->ecc_strength_ds = NAND_ECC_STRENGTH(type); + chip->ecc_step_ds = NAND_ECC_STEP(type); + chip->onfi_timing_mode_default = + type->onfi_timing_mode_default; + + *busw = type->options & NAND_BUSWIDTH_16; + + if (!mtd->name) + mtd->name = type->name; + + return true; + } + return false; +} + +/* + * Get the flash and manufacturer id and lookup if the type is supported. + */ +static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, + struct nand_chip *chip, + int *maf_id, int *dev_id, + struct nand_flash_dev *type) +{ + int busw; + int i, maf_idx; + u8 id_data[8]; + + /* Select the device */ + chip->select_chip(mtd, 0); + + /* + * Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx) + * after power-up. + */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + /* Send the command for reading device ID */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + + /* Read manufacturer and device IDs */ + *maf_id = chip->read_byte(mtd); + *dev_id = chip->read_byte(mtd); + + /* + * Try again to make sure, as some systems the bus-hold or other + * interface concerns can cause random data which looks like a + * possibly credible NAND flash to appear. If the two results do + * not match, ignore the device completely. + */ + + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + + /* Read entire ID string */ + for (i = 0; i < 8; i++) + id_data[i] = chip->read_byte(mtd); + + if (id_data[0] != *maf_id || id_data[1] != *dev_id) { + pr_info("second ID read did not match %02x,%02x against %02x,%02x\n", + *maf_id, *dev_id, id_data[0], id_data[1]); + return ERR_PTR(-ENODEV); + } + + if (!type) + type = nand_flash_ids; + + for (; type->name != NULL; type++) { + if (is_full_id_nand(type)) { + if (find_full_id_nand(mtd, chip, type, id_data, &busw)) + goto ident_done; + } else if (*dev_id == type->dev_id) { + break; + } + } + + chip->onfi_version = 0; + if (!type->name || !type->pagesize) { + /* Check if the chip is ONFI compliant */ + if (nand_flash_detect_onfi(mtd, chip, &busw)) + goto ident_done; + + /* Check if the chip is JEDEC compliant */ + if (nand_flash_detect_jedec(mtd, chip, &busw)) + goto ident_done; + } + + if (!type->name) + return ERR_PTR(-ENODEV); + + if (!mtd->name) + mtd->name = type->name; + + chip->chipsize = (uint64_t)type->chipsize << 20; + + if (!type->pagesize && chip->init_size) { + /* Set the pagesize, oobsize, erasesize by the driver */ + busw = chip->init_size(mtd, chip, id_data); + } else if (!type->pagesize) { + /* Decode parameters from extended ID */ + nand_decode_ext_id(mtd, chip, id_data, &busw); + } else { + nand_decode_id(mtd, chip, type, id_data, &busw); + } + /* Get chip options */ + chip->options |= type->options; + + /* + * Check if chip is not a Samsung device. Do not clear the + * options for chips which do not have an extended id. + */ + if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize) + chip->options &= ~NAND_SAMSUNG_LP_OPTIONS; +ident_done: + + /* Try to identify manufacturer */ + for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) { + if (nand_manuf_ids[maf_idx].id == *maf_id) + break; + } + + if (chip->options & NAND_BUSWIDTH_AUTO) { + WARN_ON(chip->options & NAND_BUSWIDTH_16); + chip->options |= busw; + nand_set_defaults(chip, busw); + } else if (busw != (chip->options & NAND_BUSWIDTH_16)) { + /* + * Check, if buswidth is correct. Hardware drivers should set + * chip correct! + */ + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, mtd->name); + pr_warn("bus width %d instead %d bit\n", + (chip->options & NAND_BUSWIDTH_16) ? 16 : 8, + busw ? 16 : 8); + return ERR_PTR(-EINVAL); + } + + nand_decode_bbm_options(mtd, chip, id_data); + + /* Calculate the address shift from the page size */ + chip->page_shift = ffs(mtd->writesize) - 1; + /* Convert chipsize to number of pages per chip -1 */ + chip->pagemask = (chip->chipsize >> chip->page_shift) - 1; + + chip->bbt_erase_shift = chip->phys_erase_shift = + ffs(mtd->erasesize) - 1; + if (chip->chipsize & 0xffffffff) + chip->chip_shift = ffs((unsigned)chip->chipsize) - 1; + else { + chip->chip_shift = ffs((unsigned)(chip->chipsize >> 32)); + chip->chip_shift += 32 - 1; + } + + chip->badblockbits = 8; + chip->erase = single_erase; + + /* Do not replace user supplied command function! */ + if (mtd->writesize > 512 && chip->cmdfunc == nand_command) + chip->cmdfunc = nand_command_lp; + + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + + if (chip->onfi_version) + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + chip->onfi_params.model); + else if (chip->jedec_version) + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + chip->jedec_params.model); + else + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, + type->name); + + pr_info("%d MiB, %s, erase size: %d KiB, page size: %d, OOB size: %d\n", + (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC", + mtd->erasesize >> 10, mtd->writesize, mtd->oobsize); + return type; +} + +/** + * nand_scan_ident - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * @maxchips: number of chips to scan for + * @table: alternative NAND ID table + * + * This is the first phase of the normal nand_scan() function. It reads the + * flash ID and sets up MTD fields accordingly. + * + * The mtd->owner field must be set to the module of the caller. + */ +int nand_scan_ident(struct mtd_info *mtd, int maxchips, + struct nand_flash_dev *table) +{ + int i, nand_maf_id, nand_dev_id; + struct nand_chip *chip = mtd->priv; + struct nand_flash_dev *type; + + /* Set the default functions */ + nand_set_defaults(chip, chip->options & NAND_BUSWIDTH_16); + + /* Read the flash type */ + type = nand_get_flash_type(mtd, chip, &nand_maf_id, + &nand_dev_id, table); + + if (IS_ERR(type)) { + if (!(chip->options & NAND_SCAN_SILENT_NODEV)) + pr_warn("No NAND device found\n"); + chip->select_chip(mtd, -1); + return PTR_ERR(type); + } + + chip->select_chip(mtd, -1); + + /* Check for a chip array */ + for (i = 1; i < maxchips; i++) { + chip->select_chip(mtd, i); + /* See comment in nand_get_flash_type for reset */ + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + /* Send the command for reading device ID */ + chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + /* Read manufacturer and device IDs */ + if (nand_maf_id != chip->read_byte(mtd) || + nand_dev_id != chip->read_byte(mtd)) { + chip->select_chip(mtd, -1); + break; + } + chip->select_chip(mtd, -1); + } + if (i > 1) + pr_info("%d chips detected\n", i); + + /* Store the number of chips and calc total size for mtd */ + chip->numchips = i; + mtd->size = i * chip->chipsize; + + return 0; +} +EXPORT_SYMBOL(nand_scan_ident); + +/* + * Check if the chip configuration meet the datasheet requirements. + + * If our configuration corrects A bits per B bytes and the minimum + * required correction level is X bits per Y bytes, then we must ensure + * both of the following are true: + * + * (1) A / B >= X / Y + * (2) A >= X + * + * Requirement (1) ensures we can correct for the required bitflip density. + * Requirement (2) ensures we can correct even when all bitflips are clumped + * in the same sector. + */ +static bool nand_ecc_strength_good(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; + int corr, ds_corr; + + if (ecc->size == 0 || chip->ecc_step_ds == 0) + /* Not enough information */ + return true; + + /* + * We get the number of corrected bits per page to compare + * the correction density. + */ + corr = (mtd->writesize * ecc->strength) / ecc->size; + ds_corr = (mtd->writesize * chip->ecc_strength_ds) / chip->ecc_step_ds; + + return corr >= ds_corr && ecc->strength >= chip->ecc_strength_ds; +} + +/** + * nand_scan_tail - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * + * This is the second phase of the normal nand_scan() function. It fills out + * all the uninitialized function pointers with the defaults and scans for a + * bad block table if appropriate. + */ +int nand_scan_tail(struct mtd_info *mtd) +{ + int i; + struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_buffers *nbuf; + + /* New bad blocks should be marked in OOB, flash-based BBT, or both */ + BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) && + !(chip->bbt_options & NAND_BBT_USE_FLASH)); + + if (!(chip->options & NAND_OWN_BUFFERS)) { + nbuf = kzalloc(sizeof(*nbuf) + mtd->writesize + + mtd->oobsize * 3, GFP_KERNEL); + if (!nbuf) + return -ENOMEM; + nbuf->ecccalc = (uint8_t *)(nbuf + 1); + nbuf->ecccode = nbuf->ecccalc + mtd->oobsize; + nbuf->databuf = nbuf->ecccode + mtd->oobsize; + + chip->buffers = nbuf; + } else { + if (!chip->buffers) + return -ENOMEM; + } + + /* Set the internal oob buffer location, just after the page data */ + chip->oob_poi = chip->buffers->databuf + mtd->writesize; + + /* + * If no default placement scheme is given, select an appropriate one. + */ + if (!ecc->layout && (ecc->mode != NAND_ECC_SOFT_BCH)) { + switch (mtd->oobsize) { + case 8: + ecc->layout = &nand_oob_8; + break; + case 16: + ecc->layout = &nand_oob_16; + break; + case 64: + ecc->layout = &nand_oob_64; + break; + case 128: + ecc->layout = &nand_oob_128; + break; + default: + pr_warn("No oob scheme defined for oobsize %d\n", + mtd->oobsize); + BUG(); + } + } + + if (!chip->write_page) + chip->write_page = nand_write_page; + + /* + * Check ECC mode, default to software if 3byte/512byte hardware ECC is + * selected and we have 256 byte pagesize fallback to software ECC + */ + + switch (ecc->mode) { + case NAND_ECC_HW_OOB_FIRST: + /* Similar to NAND_ECC_HW, but a separate read_page handle */ + if (!ecc->calculate || !ecc->correct || !ecc->hwctl) { + pr_warn("No ECC functions supplied; hardware ECC not possible\n"); + BUG(); + } + if (!ecc->read_page) + ecc->read_page = nand_read_page_hwecc_oob_first; + + case NAND_ECC_HW: + /* Use standard hwecc read page function? */ + if (!ecc->read_page) + ecc->read_page = nand_read_page_hwecc; + if (!ecc->write_page) + ecc->write_page = nand_write_page_hwecc; + if (!ecc->read_page_raw) + ecc->read_page_raw = nand_read_page_raw; + if (!ecc->write_page_raw) + ecc->write_page_raw = nand_write_page_raw; + if (!ecc->read_oob) + ecc->read_oob = nand_read_oob_std; + if (!ecc->write_oob) + ecc->write_oob = nand_write_oob_std; + if (!ecc->read_subpage) + ecc->read_subpage = nand_read_subpage; + if (!ecc->write_subpage) + ecc->write_subpage = nand_write_subpage_hwecc; + + case NAND_ECC_HW_SYNDROME: + if ((!ecc->calculate || !ecc->correct || !ecc->hwctl) && + (!ecc->read_page || + ecc->read_page == nand_read_page_hwecc || + !ecc->write_page || + ecc->write_page == nand_write_page_hwecc)) { + pr_warn("No ECC functions supplied; hardware ECC not possible\n"); + BUG(); + } + /* Use standard syndrome read/write page function? */ + if (!ecc->read_page) + ecc->read_page = nand_read_page_syndrome; + if (!ecc->write_page) + ecc->write_page = nand_write_page_syndrome; + if (!ecc->read_page_raw) + ecc->read_page_raw = nand_read_page_raw_syndrome; + if (!ecc->write_page_raw) + ecc->write_page_raw = nand_write_page_raw_syndrome; + if (!ecc->read_oob) + ecc->read_oob = nand_read_oob_syndrome; + if (!ecc->write_oob) + ecc->write_oob = nand_write_oob_syndrome; + + if (mtd->writesize >= ecc->size) { + if (!ecc->strength) { + pr_warn("Driver must set ecc.strength when using hardware ECC\n"); + BUG(); + } + break; + } + pr_warn("%d byte HW ECC not possible on %d byte page size, fallback to SW ECC\n", + ecc->size, mtd->writesize); + ecc->mode = NAND_ECC_SOFT; + + case NAND_ECC_SOFT: + ecc->calculate = nand_calculate_ecc; + ecc->correct = nand_correct_data; + ecc->read_page = nand_read_page_swecc; + ecc->read_subpage = nand_read_subpage; + ecc->write_page = nand_write_page_swecc; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->write_oob = nand_write_oob_std; + if (!ecc->size) + ecc->size = 256; + ecc->bytes = 3; + ecc->strength = 1; + break; + + case NAND_ECC_SOFT_BCH: + if (!mtd_nand_has_bch()) { + pr_warn("CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + BUG(); + } + ecc->calculate = nand_bch_calculate_ecc; + ecc->correct = nand_bch_correct_data; + ecc->read_page = nand_read_page_swecc; + ecc->read_subpage = nand_read_subpage; + ecc->write_page = nand_write_page_swecc; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->write_oob = nand_write_oob_std; + /* + * Board driver should supply ecc.size and ecc.strength values + * to select how many bits are correctable. Otherwise, default + * to 4 bits for large page devices. + */ + if (!ecc->size && (mtd->oobsize >= 64)) { + ecc->size = 512; + ecc->strength = 4; + } + + /* See nand_bch_init() for details. */ + ecc->bytes = DIV_ROUND_UP( + ecc->strength * fls(8 * ecc->size), 8); + ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes, + &ecc->layout); + if (!ecc->priv) { + pr_warn("BCH ECC initialization failed!\n"); + BUG(); + } + break; + + case NAND_ECC_NONE: + pr_warn("NAND_ECC_NONE selected by board driver. This is not recommended!\n"); + ecc->read_page = nand_read_page_raw; + ecc->write_page = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->write_oob = nand_write_oob_std; + ecc->size = mtd->writesize; + ecc->bytes = 0; + ecc->strength = 0; + break; + + default: + pr_warn("Invalid NAND_ECC_MODE %d\n", ecc->mode); + BUG(); + } + + /* For many systems, the standard OOB write also works for raw */ + if (!ecc->read_oob_raw) + ecc->read_oob_raw = ecc->read_oob; + if (!ecc->write_oob_raw) + ecc->write_oob_raw = ecc->write_oob; + + /* + * The number of bytes available for a client to place data into + * the out of band area. + */ + ecc->layout->oobavail = 0; + for (i = 0; ecc->layout->oobfree[i].length + && i < ARRAY_SIZE(ecc->layout->oobfree); i++) + ecc->layout->oobavail += ecc->layout->oobfree[i].length; + mtd->oobavail = ecc->layout->oobavail; + + /* ECC sanity check: warn if it's too weak */ + if (!nand_ecc_strength_good(mtd)) + pr_warn("WARNING: %s: the ECC used on your system is too weak compared to the one required by the NAND chip\n", + mtd->name); + + /* + * Set the number of read / write steps for one page depending on ECC + * mode. + */ + ecc->steps = mtd->writesize / ecc->size; + if (ecc->steps * ecc->size != mtd->writesize) { + pr_warn("Invalid ECC parameters\n"); + BUG(); + } + ecc->total = ecc->steps * ecc->bytes; + + /* Allow subpage writes up to ecc.steps. Not possible for MLC flash */ + if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && nand_is_slc(chip)) { + switch (ecc->steps) { + case 2: + mtd->subpage_sft = 1; + break; + case 4: + case 8: + case 16: + mtd->subpage_sft = 2; + break; + } + } + chip->subpagesize = mtd->writesize >> mtd->subpage_sft; + + /* Initialize state */ + chip->state = FL_READY; + + /* Invalidate the pagebuffer reference */ + chip->pagebuf = -1; + + /* Large page NAND with SOFT_ECC should support subpage reads */ + switch (ecc->mode) { + case NAND_ECC_SOFT: + case NAND_ECC_SOFT_BCH: + if (chip->page_shift > 9) + chip->options |= NAND_SUBPAGE_READ; + break; + + default: + break; + } + + /* Fill in remaining MTD driver data */ + mtd->type = nand_is_slc(chip) ? MTD_NANDFLASH : MTD_MLCNANDFLASH; + mtd->flags = (chip->options & NAND_ROM) ? MTD_CAP_ROM : + MTD_CAP_NANDFLASH; + mtd->_erase = nand_erase; + mtd->_point = NULL; + mtd->_unpoint = NULL; + mtd->_read = nand_read; + mtd->_write = nand_write; + mtd->_panic_write = panic_nand_write; + mtd->_read_oob = nand_read_oob; + mtd->_write_oob = nand_write_oob; + mtd->_sync = nand_sync; + mtd->_lock = NULL; + mtd->_unlock = NULL; + mtd->_suspend = nand_suspend; + mtd->_resume = nand_resume; + mtd->_reboot = nand_shutdown; + mtd->_block_isreserved = nand_block_isreserved; + mtd->_block_isbad = nand_block_isbad; + mtd->_block_markbad = nand_block_markbad; + mtd->writebufsize = mtd->writesize; + + /* propagate ecc info to mtd_info */ + mtd->ecclayout = ecc->layout; + mtd->ecc_strength = ecc->strength; + mtd->ecc_step_size = ecc->size; + /* + * Initialize bitflip_threshold to its default prior scan_bbt() call. + * scan_bbt() might invoke mtd_read(), thus bitflip_threshold must be + * properly set. + */ + if (!mtd->bitflip_threshold) + mtd->bitflip_threshold = DIV_ROUND_UP(mtd->ecc_strength * 3, 4); + + /* Check, if we should skip the bad block table scan */ + if (chip->options & NAND_SKIP_BBTSCAN) + return 0; + + /* Build bad block table */ + return chip->scan_bbt(mtd); +} +EXPORT_SYMBOL(nand_scan_tail); + +/* + * is_module_text_address() isn't exported, and it's mostly a pointless + * test if this is a module _anyway_ -- they'd have to try _really_ hard + * to call us from in-kernel code if the core NAND support is modular. + */ +#ifdef MODULE +#define caller_is_module() (1) +#else +#define caller_is_module() \ + is_module_text_address((unsigned long)__builtin_return_address(0)) +#endif + +/** + * nand_scan - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * @maxchips: number of chips to scan for + * + * This fills out all the uninitialized function pointers with the defaults. + * The flash ID is read and the mtd/chip structures are filled with the + * appropriate values. The mtd->owner field must be set to the module of the + * caller. + */ +int nand_scan(struct mtd_info *mtd, int maxchips) +{ + int ret; + + /* Many callers got this wrong, so check for it for a while... */ + if (!mtd->owner && caller_is_module()) { + pr_crit("%s called with NULL mtd->owner!\n", __func__); + BUG(); + } + + ret = nand_scan_ident(mtd, maxchips, NULL); + if (!ret) + ret = nand_scan_tail(mtd); + return ret; +} +EXPORT_SYMBOL(nand_scan); + +/** + * nand_release - [NAND Interface] Free resources held by the NAND device + * @mtd: MTD device structure + */ +void nand_release(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + + if (chip->ecc.mode == NAND_ECC_SOFT_BCH) + nand_bch_free((struct nand_bch_control *)chip->ecc.priv); + + mtd_device_unregister(mtd); + + /* Free bad block table memory */ + kfree(chip->bbt); + if (!(chip->options & NAND_OWN_BUFFERS)) + kfree(chip->buffers); + + /* Free bad block descriptor memory */ + if (chip->badblock_pattern && chip->badblock_pattern->options + & NAND_BBT_DYNAMICSTRUCT) + kfree(chip->badblock_pattern); +} +EXPORT_SYMBOL_GPL(nand_release); + +static int __init nand_base_init(void) +{ + led_trigger_register_simple("nand-disk", &nand_led_trigger); + return 0; +} + +static void __exit nand_base_exit(void) +{ + led_trigger_unregister_simple(nand_led_trigger); +} + +module_init(nand_base_init); +module_exit(nand_base_exit); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Steven J. Hill <sjhill@realitydiluted.com>"); +MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>"); +MODULE_DESCRIPTION("Generic NAND flash driver code"); diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c new file mode 100644 index 000000000..9bb8453d2 --- /dev/null +++ b/drivers/mtd/nand/nand_bbt.c @@ -0,0 +1,1375 @@ +/* + * drivers/mtd/nand_bbt.c + * + * Overview: + * Bad block table support for the NAND driver + * + * Copyright © 2004 Thomas Gleixner (tglx@linutronix.de) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Description: + * + * When nand_scan_bbt is called, then it tries to find the bad block table + * depending on the options in the BBT descriptor(s). If no flash based BBT + * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory + * marked good / bad blocks. This information is used to create a memory BBT. + * Once a new bad block is discovered then the "factory" information is updated + * on the device. + * If a flash based BBT is specified then the function first tries to find the + * BBT on flash. If a BBT is found then the contents are read and the memory + * based BBT is created. If a mirrored BBT is selected then the mirror is + * searched too and the versions are compared. If the mirror has a greater + * version number, then the mirror BBT is used to build the memory based BBT. + * If the tables are not versioned, then we "or" the bad block information. + * If one of the BBTs is out of date or does not exist it is (re)created. + * If no BBT exists at all then the device is scanned for factory marked + * good / bad blocks and the bad block tables are created. + * + * For manufacturer created BBTs like the one found on M-SYS DOC devices + * the BBT is searched and read but never created + * + * The auto generated bad block table is located in the last good blocks + * of the device. The table is mirrored, so it can be updated eventually. + * The table is marked in the OOB area with an ident pattern and a version + * number which indicates which of both tables is more up to date. If the NAND + * controller needs the complete OOB area for the ECC information then the + * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of + * course): it moves the ident pattern and the version byte into the data area + * and the OOB area will remain untouched. + * + * The table uses 2 bits per block + * 11b: block is good + * 00b: block is factory marked bad + * 01b, 10b: block is marked bad due to wear + * + * The memory bad block table uses the following scheme: + * 00b: block is good + * 01b: block is marked bad due to wear + * 10b: block is reserved (to protect the bbt area) + * 11b: block is factory marked bad + * + * Multichip devices like DOC store the bad block info per floor. + * + * Following assumptions are made: + * - bbts start at a page boundary, if autolocated on a block boundary + * - the space necessary for a bbt in FLASH does not exceed a block boundary + * + */ + +#include <linux/slab.h> +#include <linux/types.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/bbm.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/vmalloc.h> +#include <linux/export.h> +#include <linux/string.h> + +#define BBT_BLOCK_GOOD 0x00 +#define BBT_BLOCK_WORN 0x01 +#define BBT_BLOCK_RESERVED 0x02 +#define BBT_BLOCK_FACTORY_BAD 0x03 + +#define BBT_ENTRY_MASK 0x03 +#define BBT_ENTRY_SHIFT 2 + +static int nand_update_bbt(struct mtd_info *mtd, loff_t offs); + +static inline uint8_t bbt_get_entry(struct nand_chip *chip, int block) +{ + uint8_t entry = chip->bbt[block >> BBT_ENTRY_SHIFT]; + entry >>= (block & BBT_ENTRY_MASK) * 2; + return entry & BBT_ENTRY_MASK; +} + +static inline void bbt_mark_entry(struct nand_chip *chip, int block, + uint8_t mark) +{ + uint8_t msk = (mark & BBT_ENTRY_MASK) << ((block & BBT_ENTRY_MASK) * 2); + chip->bbt[block >> BBT_ENTRY_SHIFT] |= msk; +} + +static int check_pattern_no_oob(uint8_t *buf, struct nand_bbt_descr *td) +{ + if (memcmp(buf, td->pattern, td->len)) + return -1; + return 0; +} + +/** + * check_pattern - [GENERIC] check if a pattern is in the buffer + * @buf: the buffer to search + * @len: the length of buffer to search + * @paglen: the pagelength + * @td: search pattern descriptor + * + * Check for a pattern at the given place. Used to search bad block tables and + * good / bad block identifiers. + */ +static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td) +{ + if (td->options & NAND_BBT_NO_OOB) + return check_pattern_no_oob(buf, td); + + /* Compare the pattern */ + if (memcmp(buf + paglen + td->offs, td->pattern, td->len)) + return -1; + + return 0; +} + +/** + * check_short_pattern - [GENERIC] check if a pattern is in the buffer + * @buf: the buffer to search + * @td: search pattern descriptor + * + * Check for a pattern at the given place. Used to search bad block tables and + * good / bad block identifiers. Same as check_pattern, but no optional empty + * check. + */ +static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td) +{ + /* Compare the pattern */ + if (memcmp(buf + td->offs, td->pattern, td->len)) + return -1; + return 0; +} + +/** + * add_marker_len - compute the length of the marker in data area + * @td: BBT descriptor used for computation + * + * The length will be 0 if the marker is located in OOB area. + */ +static u32 add_marker_len(struct nand_bbt_descr *td) +{ + u32 len; + + if (!(td->options & NAND_BBT_NO_OOB)) + return 0; + + len = td->len; + if (td->options & NAND_BBT_VERSION) + len++; + return len; +} + +/** + * read_bbt - [GENERIC] Read the bad block table starting from page + * @mtd: MTD device structure + * @buf: temporary buffer + * @page: the starting page + * @num: the number of bbt descriptors to read + * @td: the bbt describtion table + * @offs: block number offset in the table + * + * Read the bad block table starting from page. + */ +static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num, + struct nand_bbt_descr *td, int offs) +{ + int res, ret = 0, i, j, act = 0; + struct nand_chip *this = mtd->priv; + size_t retlen, len, totlen; + loff_t from; + int bits = td->options & NAND_BBT_NRBITS_MSK; + uint8_t msk = (uint8_t)((1 << bits) - 1); + u32 marker_len; + int reserved_block_code = td->reserved_block_code; + + totlen = (num * bits) >> 3; + marker_len = add_marker_len(td); + from = ((loff_t)page) << this->page_shift; + + while (totlen) { + len = min(totlen, (size_t)(1 << this->bbt_erase_shift)); + if (marker_len) { + /* + * In case the BBT marker is not in the OOB area it + * will be just in the first page. + */ + len -= marker_len; + from += marker_len; + marker_len = 0; + } + res = mtd_read(mtd, from, len, &retlen, buf); + if (res < 0) { + if (mtd_is_eccerr(res)) { + pr_info("nand_bbt: ECC error in BBT at 0x%012llx\n", + from & ~mtd->writesize); + return res; + } else if (mtd_is_bitflip(res)) { + pr_info("nand_bbt: corrected error in BBT at 0x%012llx\n", + from & ~mtd->writesize); + ret = res; + } else { + pr_info("nand_bbt: error reading BBT\n"); + return res; + } + } + + /* Analyse data */ + for (i = 0; i < len; i++) { + uint8_t dat = buf[i]; + for (j = 0; j < 8; j += bits, act++) { + uint8_t tmp = (dat >> j) & msk; + if (tmp == msk) + continue; + if (reserved_block_code && (tmp == reserved_block_code)) { + pr_info("nand_read_bbt: reserved block at 0x%012llx\n", + (loff_t)(offs + act) << + this->bbt_erase_shift); + bbt_mark_entry(this, offs + act, + BBT_BLOCK_RESERVED); + mtd->ecc_stats.bbtblocks++; + continue; + } + /* + * Leave it for now, if it's matured we can + * move this message to pr_debug. + */ + pr_info("nand_read_bbt: bad block at 0x%012llx\n", + (loff_t)(offs + act) << + this->bbt_erase_shift); + /* Factory marked bad or worn out? */ + if (tmp == 0) + bbt_mark_entry(this, offs + act, + BBT_BLOCK_FACTORY_BAD); + else + bbt_mark_entry(this, offs + act, + BBT_BLOCK_WORN); + mtd->ecc_stats.badblocks++; + } + } + totlen -= len; + from += len; + } + return ret; +} + +/** + * read_abs_bbt - [GENERIC] Read the bad block table starting at a given page + * @mtd: MTD device structure + * @buf: temporary buffer + * @td: descriptor for the bad block table + * @chip: read the table for a specific chip, -1 read all chips; applies only if + * NAND_BBT_PERCHIP option is set + * + * Read the bad block table for all chips starting at a given page. We assume + * that the bbt bits are in consecutive order. + */ +static int read_abs_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, int chip) +{ + struct nand_chip *this = mtd->priv; + int res = 0, i; + + if (td->options & NAND_BBT_PERCHIP) { + int offs = 0; + for (i = 0; i < this->numchips; i++) { + if (chip == -1 || chip == i) + res = read_bbt(mtd, buf, td->pages[i], + this->chipsize >> this->bbt_erase_shift, + td, offs); + if (res) + return res; + offs += this->chipsize >> this->bbt_erase_shift; + } + } else { + res = read_bbt(mtd, buf, td->pages[0], + mtd->size >> this->bbt_erase_shift, td, 0); + if (res) + return res; + } + return 0; +} + +/* BBT marker is in the first page, no OOB */ +static int scan_read_data(struct mtd_info *mtd, uint8_t *buf, loff_t offs, + struct nand_bbt_descr *td) +{ + size_t retlen; + size_t len; + + len = td->len; + if (td->options & NAND_BBT_VERSION) + len++; + + return mtd_read(mtd, offs, len, &retlen, buf); +} + +/** + * scan_read_oob - [GENERIC] Scan data+OOB region to buffer + * @mtd: MTD device structure + * @buf: temporary buffer + * @offs: offset at which to scan + * @len: length of data region to read + * + * Scan read data from data+OOB. May traverse multiple pages, interleaving + * page,OOB,page,OOB,... in buf. Completes transfer and returns the "strongest" + * ECC condition (error or bitflip). May quit on the first (non-ECC) error. + */ +static int scan_read_oob(struct mtd_info *mtd, uint8_t *buf, loff_t offs, + size_t len) +{ + struct mtd_oob_ops ops; + int res, ret = 0; + + ops.mode = MTD_OPS_PLACE_OOB; + ops.ooboffs = 0; + ops.ooblen = mtd->oobsize; + + while (len > 0) { + ops.datbuf = buf; + ops.len = min(len, (size_t)mtd->writesize); + ops.oobbuf = buf + ops.len; + + res = mtd_read_oob(mtd, offs, &ops); + if (res) { + if (!mtd_is_bitflip_or_eccerr(res)) + return res; + else if (mtd_is_eccerr(res) || !ret) + ret = res; + } + + buf += mtd->oobsize + mtd->writesize; + len -= mtd->writesize; + offs += mtd->writesize; + } + return ret; +} + +static int scan_read(struct mtd_info *mtd, uint8_t *buf, loff_t offs, + size_t len, struct nand_bbt_descr *td) +{ + if (td->options & NAND_BBT_NO_OOB) + return scan_read_data(mtd, buf, offs, td); + else + return scan_read_oob(mtd, buf, offs, len); +} + +/* Scan write data with oob to flash */ +static int scan_write_bbt(struct mtd_info *mtd, loff_t offs, size_t len, + uint8_t *buf, uint8_t *oob) +{ + struct mtd_oob_ops ops; + + ops.mode = MTD_OPS_PLACE_OOB; + ops.ooboffs = 0; + ops.ooblen = mtd->oobsize; + ops.datbuf = buf; + ops.oobbuf = oob; + ops.len = len; + + return mtd_write_oob(mtd, offs, &ops); +} + +static u32 bbt_get_ver_offs(struct mtd_info *mtd, struct nand_bbt_descr *td) +{ + u32 ver_offs = td->veroffs; + + if (!(td->options & NAND_BBT_NO_OOB)) + ver_offs += mtd->writesize; + return ver_offs; +} + +/** + * read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page + * @mtd: MTD device structure + * @buf: temporary buffer + * @td: descriptor for the bad block table + * @md: descriptor for the bad block table mirror + * + * Read the bad block table(s) for all chips starting at a given page. We + * assume that the bbt bits are in consecutive order. + */ +static void read_abs_bbts(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *td, struct nand_bbt_descr *md) +{ + struct nand_chip *this = mtd->priv; + + /* Read the primary version, if available */ + if (td->options & NAND_BBT_VERSION) { + scan_read(mtd, buf, (loff_t)td->pages[0] << this->page_shift, + mtd->writesize, td); + td->version[0] = buf[bbt_get_ver_offs(mtd, td)]; + pr_info("Bad block table at page %d, version 0x%02X\n", + td->pages[0], td->version[0]); + } + + /* Read the mirror version, if available */ + if (md && (md->options & NAND_BBT_VERSION)) { + scan_read(mtd, buf, (loff_t)md->pages[0] << this->page_shift, + mtd->writesize, md); + md->version[0] = buf[bbt_get_ver_offs(mtd, md)]; + pr_info("Bad block table at page %d, version 0x%02X\n", + md->pages[0], md->version[0]); + } +} + +/* Scan a given block partially */ +static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd, + loff_t offs, uint8_t *buf, int numpages) +{ + struct mtd_oob_ops ops; + int j, ret; + + ops.ooblen = mtd->oobsize; + ops.oobbuf = buf; + ops.ooboffs = 0; + ops.datbuf = NULL; + ops.mode = MTD_OPS_PLACE_OOB; + + for (j = 0; j < numpages; j++) { + /* + * Read the full oob until read_oob is fixed to handle single + * byte reads for 16 bit buswidth. + */ + ret = mtd_read_oob(mtd, offs, &ops); + /* Ignore ECC errors when checking for BBM */ + if (ret && !mtd_is_bitflip_or_eccerr(ret)) + return ret; + + if (check_short_pattern(buf, bd)) + return 1; + + offs += mtd->writesize; + } + return 0; +} + +/** + * create_bbt - [GENERIC] Create a bad block table by scanning the device + * @mtd: MTD device structure + * @buf: temporary buffer + * @bd: descriptor for the good/bad block search pattern + * @chip: create the table for a specific chip, -1 read all chips; applies only + * if NAND_BBT_PERCHIP option is set + * + * Create a bad block table by scanning the device for the given good/bad block + * identify pattern. + */ +static int create_bbt(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *bd, int chip) +{ + struct nand_chip *this = mtd->priv; + int i, numblocks, numpages; + int startblock; + loff_t from; + + pr_info("Scanning device for bad blocks\n"); + + if (bd->options & NAND_BBT_SCAN2NDPAGE) + numpages = 2; + else + numpages = 1; + + if (chip == -1) { + numblocks = mtd->size >> this->bbt_erase_shift; + startblock = 0; + from = 0; + } else { + if (chip >= this->numchips) { + pr_warn("create_bbt(): chipnr (%d) > available chips (%d)\n", + chip + 1, this->numchips); + return -EINVAL; + } + numblocks = this->chipsize >> this->bbt_erase_shift; + startblock = chip * numblocks; + numblocks += startblock; + from = (loff_t)startblock << this->bbt_erase_shift; + } + + if (this->bbt_options & NAND_BBT_SCANLASTPAGE) + from += mtd->erasesize - (mtd->writesize * numpages); + + for (i = startblock; i < numblocks; i++) { + int ret; + + BUG_ON(bd->options & NAND_BBT_NO_OOB); + + ret = scan_block_fast(mtd, bd, from, buf, numpages); + if (ret < 0) + return ret; + + if (ret) { + bbt_mark_entry(this, i, BBT_BLOCK_FACTORY_BAD); + pr_warn("Bad eraseblock %d at 0x%012llx\n", + i, (unsigned long long)from); + mtd->ecc_stats.badblocks++; + } + + from += (1 << this->bbt_erase_shift); + } + return 0; +} + +/** + * search_bbt - [GENERIC] scan the device for a specific bad block table + * @mtd: MTD device structure + * @buf: temporary buffer + * @td: descriptor for the bad block table + * + * Read the bad block table by searching for a given ident pattern. Search is + * preformed either from the beginning up or from the end of the device + * downwards. The search starts always at the start of a block. If the option + * NAND_BBT_PERCHIP is given, each chip is searched for a bbt, which contains + * the bad block information of this chip. This is necessary to provide support + * for certain DOC devices. + * + * The bbt ident pattern resides in the oob area of the first page in a block. + */ +static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td) +{ + struct nand_chip *this = mtd->priv; + int i, chips; + int startblock, block, dir; + int scanlen = mtd->writesize + mtd->oobsize; + int bbtblocks; + int blocktopage = this->bbt_erase_shift - this->page_shift; + + /* Search direction top -> down? */ + if (td->options & NAND_BBT_LASTBLOCK) { + startblock = (mtd->size >> this->bbt_erase_shift) - 1; + dir = -1; + } else { + startblock = 0; + dir = 1; + } + + /* Do we have a bbt per chip? */ + if (td->options & NAND_BBT_PERCHIP) { + chips = this->numchips; + bbtblocks = this->chipsize >> this->bbt_erase_shift; + startblock &= bbtblocks - 1; + } else { + chips = 1; + bbtblocks = mtd->size >> this->bbt_erase_shift; + } + + for (i = 0; i < chips; i++) { + /* Reset version information */ + td->version[i] = 0; + td->pages[i] = -1; + /* Scan the maximum number of blocks */ + for (block = 0; block < td->maxblocks; block++) { + + int actblock = startblock + dir * block; + loff_t offs = (loff_t)actblock << this->bbt_erase_shift; + + /* Read first page */ + scan_read(mtd, buf, offs, mtd->writesize, td); + if (!check_pattern(buf, scanlen, mtd->writesize, td)) { + td->pages[i] = actblock << blocktopage; + if (td->options & NAND_BBT_VERSION) { + offs = bbt_get_ver_offs(mtd, td); + td->version[i] = buf[offs]; + } + break; + } + } + startblock += this->chipsize >> this->bbt_erase_shift; + } + /* Check, if we found a bbt for each requested chip */ + for (i = 0; i < chips; i++) { + if (td->pages[i] == -1) + pr_warn("Bad block table not found for chip %d\n", i); + else + pr_info("Bad block table found at page %d, version 0x%02X\n", + td->pages[i], td->version[i]); + } + return 0; +} + +/** + * search_read_bbts - [GENERIC] scan the device for bad block table(s) + * @mtd: MTD device structure + * @buf: temporary buffer + * @td: descriptor for the bad block table + * @md: descriptor for the bad block table mirror + * + * Search and read the bad block table(s). + */ +static void search_read_bbts(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *td, + struct nand_bbt_descr *md) +{ + /* Search the primary table */ + search_bbt(mtd, buf, td); + + /* Search the mirror table */ + if (md) + search_bbt(mtd, buf, md); +} + +/** + * write_bbt - [GENERIC] (Re)write the bad block table + * @mtd: MTD device structure + * @buf: temporary buffer + * @td: descriptor for the bad block table + * @md: descriptor for the bad block table mirror + * @chipsel: selector for a specific chip, -1 for all + * + * (Re)write the bad block table. + */ +static int write_bbt(struct mtd_info *mtd, uint8_t *buf, + struct nand_bbt_descr *td, struct nand_bbt_descr *md, + int chipsel) +{ + struct nand_chip *this = mtd->priv; + struct erase_info einfo; + int i, res, chip = 0; + int bits, startblock, dir, page, offs, numblocks, sft, sftmsk; + int nrchips, pageoffs, ooboffs; + uint8_t msk[4]; + uint8_t rcode = td->reserved_block_code; + size_t retlen, len = 0; + loff_t to; + struct mtd_oob_ops ops; + + ops.ooblen = mtd->oobsize; + ops.ooboffs = 0; + ops.datbuf = NULL; + ops.mode = MTD_OPS_PLACE_OOB; + + if (!rcode) + rcode = 0xff; + /* Write bad block table per chip rather than per device? */ + if (td->options & NAND_BBT_PERCHIP) { + numblocks = (int)(this->chipsize >> this->bbt_erase_shift); + /* Full device write or specific chip? */ + if (chipsel == -1) { + nrchips = this->numchips; + } else { + nrchips = chipsel + 1; + chip = chipsel; + } + } else { + numblocks = (int)(mtd->size >> this->bbt_erase_shift); + nrchips = 1; + } + + /* Loop through the chips */ + for (; chip < nrchips; chip++) { + /* + * There was already a version of the table, reuse the page + * This applies for absolute placement too, as we have the + * page nr. in td->pages. + */ + if (td->pages[chip] != -1) { + page = td->pages[chip]; + goto write; + } + + /* + * Automatic placement of the bad block table. Search direction + * top -> down? + */ + if (td->options & NAND_BBT_LASTBLOCK) { + startblock = numblocks * (chip + 1) - 1; + dir = -1; + } else { + startblock = chip * numblocks; + dir = 1; + } + + for (i = 0; i < td->maxblocks; i++) { + int block = startblock + dir * i; + /* Check, if the block is bad */ + switch (bbt_get_entry(this, block)) { + case BBT_BLOCK_WORN: + case BBT_BLOCK_FACTORY_BAD: + continue; + } + page = block << + (this->bbt_erase_shift - this->page_shift); + /* Check, if the block is used by the mirror table */ + if (!md || md->pages[chip] != page) + goto write; + } + pr_err("No space left to write bad block table\n"); + return -ENOSPC; + write: + + /* Set up shift count and masks for the flash table */ + bits = td->options & NAND_BBT_NRBITS_MSK; + msk[2] = ~rcode; + switch (bits) { + case 1: sft = 3; sftmsk = 0x07; msk[0] = 0x00; msk[1] = 0x01; + msk[3] = 0x01; + break; + case 2: sft = 2; sftmsk = 0x06; msk[0] = 0x00; msk[1] = 0x01; + msk[3] = 0x03; + break; + case 4: sft = 1; sftmsk = 0x04; msk[0] = 0x00; msk[1] = 0x0C; + msk[3] = 0x0f; + break; + case 8: sft = 0; sftmsk = 0x00; msk[0] = 0x00; msk[1] = 0x0F; + msk[3] = 0xff; + break; + default: return -EINVAL; + } + + to = ((loff_t)page) << this->page_shift; + + /* Must we save the block contents? */ + if (td->options & NAND_BBT_SAVECONTENT) { + /* Make it block aligned */ + to &= ~((loff_t)((1 << this->bbt_erase_shift) - 1)); + len = 1 << this->bbt_erase_shift; + res = mtd_read(mtd, to, len, &retlen, buf); + if (res < 0) { + if (retlen != len) { + pr_info("nand_bbt: error reading block for writing the bad block table\n"); + return res; + } + pr_warn("nand_bbt: ECC error while reading block for writing bad block table\n"); + } + /* Read oob data */ + ops.ooblen = (len >> this->page_shift) * mtd->oobsize; + ops.oobbuf = &buf[len]; + res = mtd_read_oob(mtd, to + mtd->writesize, &ops); + if (res < 0 || ops.oobretlen != ops.ooblen) + goto outerr; + + /* Calc the byte offset in the buffer */ + pageoffs = page - (int)(to >> this->page_shift); + offs = pageoffs << this->page_shift; + /* Preset the bbt area with 0xff */ + memset(&buf[offs], 0xff, (size_t)(numblocks >> sft)); + ooboffs = len + (pageoffs * mtd->oobsize); + + } else if (td->options & NAND_BBT_NO_OOB) { + ooboffs = 0; + offs = td->len; + /* The version byte */ + if (td->options & NAND_BBT_VERSION) + offs++; + /* Calc length */ + len = (size_t)(numblocks >> sft); + len += offs; + /* Make it page aligned! */ + len = ALIGN(len, mtd->writesize); + /* Preset the buffer with 0xff */ + memset(buf, 0xff, len); + /* Pattern is located at the begin of first page */ + memcpy(buf, td->pattern, td->len); + } else { + /* Calc length */ + len = (size_t)(numblocks >> sft); + /* Make it page aligned! */ + len = ALIGN(len, mtd->writesize); + /* Preset the buffer with 0xff */ + memset(buf, 0xff, len + + (len >> this->page_shift)* mtd->oobsize); + offs = 0; + ooboffs = len; + /* Pattern is located in oob area of first page */ + memcpy(&buf[ooboffs + td->offs], td->pattern, td->len); + } + + if (td->options & NAND_BBT_VERSION) + buf[ooboffs + td->veroffs] = td->version[chip]; + + /* Walk through the memory table */ + for (i = 0; i < numblocks; i++) { + uint8_t dat; + int sftcnt = (i << (3 - sft)) & sftmsk; + dat = bbt_get_entry(this, chip * numblocks + i); + /* Do not store the reserved bbt blocks! */ + buf[offs + (i >> sft)] &= ~(msk[dat] << sftcnt); + } + + memset(&einfo, 0, sizeof(einfo)); + einfo.mtd = mtd; + einfo.addr = to; + einfo.len = 1 << this->bbt_erase_shift; + res = nand_erase_nand(mtd, &einfo, 1); + if (res < 0) + goto outerr; + + res = scan_write_bbt(mtd, to, len, buf, + td->options & NAND_BBT_NO_OOB ? NULL : + &buf[len]); + if (res < 0) + goto outerr; + + pr_info("Bad block table written to 0x%012llx, version 0x%02X\n", + (unsigned long long)to, td->version[chip]); + + /* Mark it as used */ + td->pages[chip] = page; + } + return 0; + + outerr: + pr_warn("nand_bbt: error while writing bad block table %d\n", res); + return res; +} + +/** + * nand_memory_bbt - [GENERIC] create a memory based bad block table + * @mtd: MTD device structure + * @bd: descriptor for the good/bad block search pattern + * + * The function creates a memory based bbt by scanning the device for + * manufacturer / software marked good / bad blocks. + */ +static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd) +{ + struct nand_chip *this = mtd->priv; + + return create_bbt(mtd, this->buffers->databuf, bd, -1); +} + +/** + * check_create - [GENERIC] create and write bbt(s) if necessary + * @mtd: MTD device structure + * @buf: temporary buffer + * @bd: descriptor for the good/bad block search pattern + * + * The function checks the results of the previous call to read_bbt and creates + * / updates the bbt(s) if necessary. Creation is necessary if no bbt was found + * for the chip/device. Update is necessary if one of the tables is missing or + * the version nr. of one table is less than the other. + */ +static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd) +{ + int i, chips, writeops, create, chipsel, res, res2; + struct nand_chip *this = mtd->priv; + struct nand_bbt_descr *td = this->bbt_td; + struct nand_bbt_descr *md = this->bbt_md; + struct nand_bbt_descr *rd, *rd2; + + /* Do we have a bbt per chip? */ + if (td->options & NAND_BBT_PERCHIP) + chips = this->numchips; + else + chips = 1; + + for (i = 0; i < chips; i++) { + writeops = 0; + create = 0; + rd = NULL; + rd2 = NULL; + res = res2 = 0; + /* Per chip or per device? */ + chipsel = (td->options & NAND_BBT_PERCHIP) ? i : -1; + /* Mirrored table available? */ + if (md) { + if (td->pages[i] == -1 && md->pages[i] == -1) { + create = 1; + writeops = 0x03; + } else if (td->pages[i] == -1) { + rd = md; + writeops = 0x01; + } else if (md->pages[i] == -1) { + rd = td; + writeops = 0x02; + } else if (td->version[i] == md->version[i]) { + rd = td; + if (!(td->options & NAND_BBT_VERSION)) + rd2 = md; + } else if (((int8_t)(td->version[i] - md->version[i])) > 0) { + rd = td; + writeops = 0x02; + } else { + rd = md; + writeops = 0x01; + } + } else { + if (td->pages[i] == -1) { + create = 1; + writeops = 0x01; + } else { + rd = td; + } + } + + if (create) { + /* Create the bad block table by scanning the device? */ + if (!(td->options & NAND_BBT_CREATE)) + continue; + + /* Create the table in memory by scanning the chip(s) */ + if (!(this->bbt_options & NAND_BBT_CREATE_EMPTY)) + create_bbt(mtd, buf, bd, chipsel); + + td->version[i] = 1; + if (md) + md->version[i] = 1; + } + + /* Read back first? */ + if (rd) { + res = read_abs_bbt(mtd, buf, rd, chipsel); + if (mtd_is_eccerr(res)) { + /* Mark table as invalid */ + rd->pages[i] = -1; + rd->version[i] = 0; + i--; + continue; + } + } + /* If they weren't versioned, read both */ + if (rd2) { + res2 = read_abs_bbt(mtd, buf, rd2, chipsel); + if (mtd_is_eccerr(res2)) { + /* Mark table as invalid */ + rd2->pages[i] = -1; + rd2->version[i] = 0; + i--; + continue; + } + } + + /* Scrub the flash table(s)? */ + if (mtd_is_bitflip(res) || mtd_is_bitflip(res2)) + writeops = 0x03; + + /* Update version numbers before writing */ + if (md) { + td->version[i] = max(td->version[i], md->version[i]); + md->version[i] = td->version[i]; + } + + /* Write the bad block table to the device? */ + if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) { + res = write_bbt(mtd, buf, td, md, chipsel); + if (res < 0) + return res; + } + + /* Write the mirror bad block table to the device? */ + if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) { + res = write_bbt(mtd, buf, md, td, chipsel); + if (res < 0) + return res; + } + } + return 0; +} + +/** + * mark_bbt_regions - [GENERIC] mark the bad block table regions + * @mtd: MTD device structure + * @td: bad block table descriptor + * + * The bad block table regions are marked as "bad" to prevent accidental + * erasures / writes. The regions are identified by the mark 0x02. + */ +static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td) +{ + struct nand_chip *this = mtd->priv; + int i, j, chips, block, nrblocks, update; + uint8_t oldval; + + /* Do we have a bbt per chip? */ + if (td->options & NAND_BBT_PERCHIP) { + chips = this->numchips; + nrblocks = (int)(this->chipsize >> this->bbt_erase_shift); + } else { + chips = 1; + nrblocks = (int)(mtd->size >> this->bbt_erase_shift); + } + + for (i = 0; i < chips; i++) { + if ((td->options & NAND_BBT_ABSPAGE) || + !(td->options & NAND_BBT_WRITE)) { + if (td->pages[i] == -1) + continue; + block = td->pages[i] >> (this->bbt_erase_shift - this->page_shift); + oldval = bbt_get_entry(this, block); + bbt_mark_entry(this, block, BBT_BLOCK_RESERVED); + if ((oldval != BBT_BLOCK_RESERVED) && + td->reserved_block_code) + nand_update_bbt(mtd, (loff_t)block << + this->bbt_erase_shift); + continue; + } + update = 0; + if (td->options & NAND_BBT_LASTBLOCK) + block = ((i + 1) * nrblocks) - td->maxblocks; + else + block = i * nrblocks; + for (j = 0; j < td->maxblocks; j++) { + oldval = bbt_get_entry(this, block); + bbt_mark_entry(this, block, BBT_BLOCK_RESERVED); + if (oldval != BBT_BLOCK_RESERVED) + update = 1; + block++; + } + /* + * If we want reserved blocks to be recorded to flash, and some + * new ones have been marked, then we need to update the stored + * bbts. This should only happen once. + */ + if (update && td->reserved_block_code) + nand_update_bbt(mtd, (loff_t)(block - 1) << + this->bbt_erase_shift); + } +} + +/** + * verify_bbt_descr - verify the bad block description + * @mtd: MTD device structure + * @bd: the table to verify + * + * This functions performs a few sanity checks on the bad block description + * table. + */ +static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd) +{ + struct nand_chip *this = mtd->priv; + u32 pattern_len; + u32 bits; + u32 table_size; + + if (!bd) + return; + + pattern_len = bd->len; + bits = bd->options & NAND_BBT_NRBITS_MSK; + + BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) && + !(this->bbt_options & NAND_BBT_USE_FLASH)); + BUG_ON(!bits); + + if (bd->options & NAND_BBT_VERSION) + pattern_len++; + + if (bd->options & NAND_BBT_NO_OOB) { + BUG_ON(!(this->bbt_options & NAND_BBT_USE_FLASH)); + BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB)); + BUG_ON(bd->offs); + if (bd->options & NAND_BBT_VERSION) + BUG_ON(bd->veroffs != bd->len); + BUG_ON(bd->options & NAND_BBT_SAVECONTENT); + } + + if (bd->options & NAND_BBT_PERCHIP) + table_size = this->chipsize >> this->bbt_erase_shift; + else + table_size = mtd->size >> this->bbt_erase_shift; + table_size >>= 3; + table_size *= bits; + if (bd->options & NAND_BBT_NO_OOB) + table_size += pattern_len; + BUG_ON(table_size > (1 << this->bbt_erase_shift)); +} + +/** + * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s) + * @mtd: MTD device structure + * @bd: descriptor for the good/bad block search pattern + * + * The function checks, if a bad block table(s) is/are already available. If + * not it scans the device for manufacturer marked good / bad blocks and writes + * the bad block table(s) to the selected place. + * + * The bad block table memory is allocated here. It must be freed by calling + * the nand_free_bbt function. + */ +int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd) +{ + struct nand_chip *this = mtd->priv; + int len, res = 0; + uint8_t *buf; + struct nand_bbt_descr *td = this->bbt_td; + struct nand_bbt_descr *md = this->bbt_md; + + len = mtd->size >> (this->bbt_erase_shift + 2); + /* + * Allocate memory (2bit per block) and clear the memory bad block + * table. + */ + this->bbt = kzalloc(len, GFP_KERNEL); + if (!this->bbt) + return -ENOMEM; + + /* + * If no primary table decriptor is given, scan the device to build a + * memory based bad block table. + */ + if (!td) { + if ((res = nand_memory_bbt(mtd, bd))) { + pr_err("nand_bbt: can't scan flash and build the RAM-based BBT\n"); + kfree(this->bbt); + this->bbt = NULL; + } + return res; + } + verify_bbt_descr(mtd, td); + verify_bbt_descr(mtd, md); + + /* Allocate a temporary buffer for one eraseblock incl. oob */ + len = (1 << this->bbt_erase_shift); + len += (len >> this->page_shift) * mtd->oobsize; + buf = vmalloc(len); + if (!buf) { + kfree(this->bbt); + this->bbt = NULL; + return -ENOMEM; + } + + /* Is the bbt at a given page? */ + if (td->options & NAND_BBT_ABSPAGE) { + read_abs_bbts(mtd, buf, td, md); + } else { + /* Search the bad block table using a pattern in oob */ + search_read_bbts(mtd, buf, td, md); + } + + res = check_create(mtd, buf, bd); + + /* Prevent the bbt regions from erasing / writing */ + mark_bbt_region(mtd, td); + if (md) + mark_bbt_region(mtd, md); + + vfree(buf); + return res; +} + +/** + * nand_update_bbt - update bad block table(s) + * @mtd: MTD device structure + * @offs: the offset of the newly marked block + * + * The function updates the bad block table(s). + */ +static int nand_update_bbt(struct mtd_info *mtd, loff_t offs) +{ + struct nand_chip *this = mtd->priv; + int len, res = 0; + int chip, chipsel; + uint8_t *buf; + struct nand_bbt_descr *td = this->bbt_td; + struct nand_bbt_descr *md = this->bbt_md; + + if (!this->bbt || !td) + return -EINVAL; + + /* Allocate a temporary buffer for one eraseblock incl. oob */ + len = (1 << this->bbt_erase_shift); + len += (len >> this->page_shift) * mtd->oobsize; + buf = kmalloc(len, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + /* Do we have a bbt per chip? */ + if (td->options & NAND_BBT_PERCHIP) { + chip = (int)(offs >> this->chip_shift); + chipsel = chip; + } else { + chip = 0; + chipsel = -1; + } + + td->version[chip]++; + if (md) + md->version[chip]++; + + /* Write the bad block table to the device? */ + if (td->options & NAND_BBT_WRITE) { + res = write_bbt(mtd, buf, td, md, chipsel); + if (res < 0) + goto out; + } + /* Write the mirror bad block table to the device? */ + if (md && (md->options & NAND_BBT_WRITE)) { + res = write_bbt(mtd, buf, md, td, chipsel); + } + + out: + kfree(buf); + return res; +} + +/* + * Define some generic bad / good block scan pattern which are used + * while scanning a device for factory marked good / bad blocks. + */ +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +/* Generic flash bbt descriptors */ +static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' }; +static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 8, + .len = 4, + .veroffs = 12, + .maxblocks = NAND_BBT_SCAN_MAXBLOCKS, + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 8, + .len = 4, + .veroffs = 12, + .maxblocks = NAND_BBT_SCAN_MAXBLOCKS, + .pattern = mirror_pattern +}; + +static struct nand_bbt_descr bbt_main_no_oob_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP + | NAND_BBT_NO_OOB, + .len = 4, + .veroffs = 4, + .maxblocks = NAND_BBT_SCAN_MAXBLOCKS, + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_no_oob_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP + | NAND_BBT_NO_OOB, + .len = 4, + .veroffs = 4, + .maxblocks = NAND_BBT_SCAN_MAXBLOCKS, + .pattern = mirror_pattern +}; + +#define BADBLOCK_SCAN_MASK (~NAND_BBT_NO_OOB) +/** + * nand_create_badblock_pattern - [INTERN] Creates a BBT descriptor structure + * @this: NAND chip to create descriptor for + * + * This function allocates and initializes a nand_bbt_descr for BBM detection + * based on the properties of @this. The new descriptor is stored in + * this->badblock_pattern. Thus, this->badblock_pattern should be NULL when + * passed to this function. + */ +static int nand_create_badblock_pattern(struct nand_chip *this) +{ + struct nand_bbt_descr *bd; + if (this->badblock_pattern) { + pr_warn("Bad block pattern already allocated; not replacing\n"); + return -EINVAL; + } + bd = kzalloc(sizeof(*bd), GFP_KERNEL); + if (!bd) + return -ENOMEM; + bd->options = this->bbt_options & BADBLOCK_SCAN_MASK; + bd->offs = this->badblockpos; + bd->len = (this->options & NAND_BUSWIDTH_16) ? 2 : 1; + bd->pattern = scan_ff_pattern; + bd->options |= NAND_BBT_DYNAMICSTRUCT; + this->badblock_pattern = bd; + return 0; +} + +/** + * nand_default_bbt - [NAND Interface] Select a default bad block table for the device + * @mtd: MTD device structure + * + * This function selects the default bad block table support for the device and + * calls the nand_scan_bbt function. + */ +int nand_default_bbt(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + int ret; + + /* Is a flash based bad block table requested? */ + if (this->bbt_options & NAND_BBT_USE_FLASH) { + /* Use the default pattern descriptors */ + if (!this->bbt_td) { + if (this->bbt_options & NAND_BBT_NO_OOB) { + this->bbt_td = &bbt_main_no_oob_descr; + this->bbt_md = &bbt_mirror_no_oob_descr; + } else { + this->bbt_td = &bbt_main_descr; + this->bbt_md = &bbt_mirror_descr; + } + } + } else { + this->bbt_td = NULL; + this->bbt_md = NULL; + } + + if (!this->badblock_pattern) { + ret = nand_create_badblock_pattern(this); + if (ret) + return ret; + } + + return nand_scan_bbt(mtd, this->badblock_pattern); +} + +/** + * nand_isreserved_bbt - [NAND Interface] Check if a block is reserved + * @mtd: MTD device structure + * @offs: offset in the device + */ +int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs) +{ + struct nand_chip *this = mtd->priv; + int block; + + block = (int)(offs >> this->bbt_erase_shift); + return bbt_get_entry(this, block) == BBT_BLOCK_RESERVED; +} + +/** + * nand_isbad_bbt - [NAND Interface] Check if a block is bad + * @mtd: MTD device structure + * @offs: offset in the device + * @allowbbt: allow access to bad block table region + */ +int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt) +{ + struct nand_chip *this = mtd->priv; + int block, res; + + block = (int)(offs >> this->bbt_erase_shift); + res = bbt_get_entry(this, block); + + pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: (block %d) 0x%02x\n", + (unsigned int)offs, block, res); + + switch (res) { + case BBT_BLOCK_GOOD: + return 0; + case BBT_BLOCK_WORN: + return 1; + case BBT_BLOCK_RESERVED: + return allowbbt ? 0 : 1; + } + return 1; +} + +/** + * nand_markbad_bbt - [NAND Interface] Mark a block bad in the BBT + * @mtd: MTD device structure + * @offs: offset of the bad block + */ +int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs) +{ + struct nand_chip *this = mtd->priv; + int block, ret = 0; + + block = (int)(offs >> this->bbt_erase_shift); + + /* Mark bad block in memory */ + bbt_mark_entry(this, block, BBT_BLOCK_WORN); + + /* Update flash-based bad block table */ + if (this->bbt_options & NAND_BBT_USE_FLASH) + ret = nand_update_bbt(mtd, offs); + + return ret; +} + +EXPORT_SYMBOL(nand_scan_bbt); diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/nand_bch.c new file mode 100644 index 000000000..3803e0bba --- /dev/null +++ b/drivers/mtd/nand/nand_bch.c @@ -0,0 +1,243 @@ +/* + * This file provides ECC correction for more than 1 bit per block of data, + * using binary BCH codes. It relies on the generic BCH library lib/bch.c. + * + * Copyright © 2011 Ivan Djelic <ivan.djelic@parrot.com> + * + * This file is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 or (at your option) any + * later version. + * + * This file is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this file; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. + */ + +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/bitops.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_bch.h> +#include <linux/bch.h> + +/** + * struct nand_bch_control - private NAND BCH control structure + * @bch: BCH control structure + * @ecclayout: private ecc layout for this BCH configuration + * @errloc: error location array + * @eccmask: XOR ecc mask, allows erased pages to be decoded as valid + */ +struct nand_bch_control { + struct bch_control *bch; + struct nand_ecclayout ecclayout; + unsigned int *errloc; + unsigned char *eccmask; +}; + +/** + * nand_bch_calculate_ecc - [NAND Interface] Calculate ECC for data block + * @mtd: MTD block structure + * @buf: input buffer with raw data + * @code: output buffer with ECC + */ +int nand_bch_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf, + unsigned char *code) +{ + const struct nand_chip *chip = mtd->priv; + struct nand_bch_control *nbc = chip->ecc.priv; + unsigned int i; + + memset(code, 0, chip->ecc.bytes); + encode_bch(nbc->bch, buf, chip->ecc.size, code); + + /* apply mask so that an erased page is a valid codeword */ + for (i = 0; i < chip->ecc.bytes; i++) + code[i] ^= nbc->eccmask[i]; + + return 0; +} +EXPORT_SYMBOL(nand_bch_calculate_ecc); + +/** + * nand_bch_correct_data - [NAND Interface] Detect and correct bit error(s) + * @mtd: MTD block structure + * @buf: raw data read from the chip + * @read_ecc: ECC from the chip + * @calc_ecc: the ECC calculated from raw data + * + * Detect and correct bit errors for a data byte block + */ +int nand_bch_correct_data(struct mtd_info *mtd, unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc) +{ + const struct nand_chip *chip = mtd->priv; + struct nand_bch_control *nbc = chip->ecc.priv; + unsigned int *errloc = nbc->errloc; + int i, count; + + count = decode_bch(nbc->bch, NULL, chip->ecc.size, read_ecc, calc_ecc, + NULL, errloc); + if (count > 0) { + for (i = 0; i < count; i++) { + if (errloc[i] < (chip->ecc.size*8)) + /* error is located in data, correct it */ + buf[errloc[i] >> 3] ^= (1 << (errloc[i] & 7)); + /* else error in ecc, no action needed */ + + pr_debug("%s: corrected bitflip %u\n", __func__, + errloc[i]); + } + } else if (count < 0) { + printk(KERN_ERR "ecc unrecoverable error\n"); + count = -1; + } + return count; +} +EXPORT_SYMBOL(nand_bch_correct_data); + +/** + * nand_bch_init - [NAND Interface] Initialize NAND BCH error correction + * @mtd: MTD block structure + * @eccsize: ecc block size in bytes + * @eccbytes: ecc length in bytes + * @ecclayout: output default layout + * + * Returns: + * a pointer to a new NAND BCH control structure, or NULL upon failure + * + * Initialize NAND BCH error correction. Parameters @eccsize and @eccbytes + * are used to compute BCH parameters m (Galois field order) and t (error + * correction capability). @eccbytes should be equal to the number of bytes + * required to store m*t bits, where m is such that 2^m-1 > @eccsize*8. + * + * Example: to configure 4 bit correction per 512 bytes, you should pass + * @eccsize = 512 (thus, m=13 is the smallest integer such that 2^m-1 > 512*8) + * @eccbytes = 7 (7 bytes are required to store m*t = 13*4 = 52 bits) + */ +struct nand_bch_control * +nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes, + struct nand_ecclayout **ecclayout) +{ + unsigned int m, t, eccsteps, i; + struct nand_ecclayout *layout; + struct nand_bch_control *nbc = NULL; + unsigned char *erased_page; + + if (!eccsize || !eccbytes) { + printk(KERN_WARNING "ecc parameters not supplied\n"); + goto fail; + } + + m = fls(1+8*eccsize); + t = (eccbytes*8)/m; + + nbc = kzalloc(sizeof(*nbc), GFP_KERNEL); + if (!nbc) + goto fail; + + nbc->bch = init_bch(m, t, 0); + if (!nbc->bch) + goto fail; + + /* verify that eccbytes has the expected value */ + if (nbc->bch->ecc_bytes != eccbytes) { + printk(KERN_WARNING "invalid eccbytes %u, should be %u\n", + eccbytes, nbc->bch->ecc_bytes); + goto fail; + } + + eccsteps = mtd->writesize/eccsize; + + /* if no ecc placement scheme was provided, build one */ + if (!*ecclayout) { + + /* handle large page devices only */ + if (mtd->oobsize < 64) { + printk(KERN_WARNING "must provide an oob scheme for " + "oobsize %d\n", mtd->oobsize); + goto fail; + } + + layout = &nbc->ecclayout; + layout->eccbytes = eccsteps*eccbytes; + + /* reserve 2 bytes for bad block marker */ + if (layout->eccbytes+2 > mtd->oobsize) { + printk(KERN_WARNING "no suitable oob scheme available " + "for oobsize %d eccbytes %u\n", mtd->oobsize, + eccbytes); + goto fail; + } + /* put ecc bytes at oob tail */ + for (i = 0; i < layout->eccbytes; i++) + layout->eccpos[i] = mtd->oobsize-layout->eccbytes+i; + + layout->oobfree[0].offset = 2; + layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes; + + *ecclayout = layout; + } + + /* sanity checks */ + if (8*(eccsize+eccbytes) >= (1 << m)) { + printk(KERN_WARNING "eccsize %u is too large\n", eccsize); + goto fail; + } + if ((*ecclayout)->eccbytes != (eccsteps*eccbytes)) { + printk(KERN_WARNING "invalid ecc layout\n"); + goto fail; + } + + nbc->eccmask = kmalloc(eccbytes, GFP_KERNEL); + nbc->errloc = kmalloc(t*sizeof(*nbc->errloc), GFP_KERNEL); + if (!nbc->eccmask || !nbc->errloc) + goto fail; + /* + * compute and store the inverted ecc of an erased ecc block + */ + erased_page = kmalloc(eccsize, GFP_KERNEL); + if (!erased_page) + goto fail; + + memset(erased_page, 0xff, eccsize); + memset(nbc->eccmask, 0, eccbytes); + encode_bch(nbc->bch, erased_page, eccsize, nbc->eccmask); + kfree(erased_page); + + for (i = 0; i < eccbytes; i++) + nbc->eccmask[i] ^= 0xff; + + return nbc; +fail: + nand_bch_free(nbc); + return NULL; +} +EXPORT_SYMBOL(nand_bch_init); + +/** + * nand_bch_free - [NAND Interface] Release NAND BCH ECC resources + * @nbc: NAND BCH control structure + */ +void nand_bch_free(struct nand_bch_control *nbc) +{ + if (nbc) { + free_bch(nbc->bch); + kfree(nbc->errloc); + kfree(nbc->eccmask); + kfree(nbc); + } +} +EXPORT_SYMBOL(nand_bch_free); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Ivan Djelic <ivan.djelic@parrot.com>"); +MODULE_DESCRIPTION("NAND software BCH ECC support"); diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c new file mode 100644 index 000000000..97c4c0216 --- /dev/null +++ b/drivers/mtd/nand/nand_ecc.c @@ -0,0 +1,533 @@ +/* + * This file contains an ECC algorithm that detects and corrects 1 bit + * errors in a 256 byte block of data. + * + * drivers/mtd/nand/nand_ecc.c + * + * Copyright © 2008 Koninklijke Philips Electronics NV. + * Author: Frans Meulenbroeks + * + * Completely replaces the previous ECC implementation which was written by: + * Steven J. Hill (sjhill@realitydiluted.com) + * Thomas Gleixner (tglx@linutronix.de) + * + * Information on how this algorithm works and how it was developed + * can be found in Documentation/mtd/nand_ecc.txt + * + * This file is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 or (at your option) any + * later version. + * + * This file is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this file; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA. + * + */ + +/* + * The STANDALONE macro is useful when running the code outside the kernel + * e.g. when running the code in a testbed or a benchmark program. + * When STANDALONE is used, the module related macros are commented out + * as well as the linux include files. + * Instead a private definition of mtd_info is given to satisfy the compiler + * (the code does not use mtd_info, so the code does not care) + */ +#ifndef STANDALONE +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <asm/byteorder.h> +#else +#include <stdint.h> +struct mtd_info; +#define EXPORT_SYMBOL(x) /* x */ + +#define MODULE_LICENSE(x) /* x */ +#define MODULE_AUTHOR(x) /* x */ +#define MODULE_DESCRIPTION(x) /* x */ + +#define pr_err printf +#endif + +/* + * invparity is a 256 byte table that contains the odd parity + * for each byte. So if the number of bits in a byte is even, + * the array element is 1, and when the number of bits is odd + * the array eleemnt is 0. + */ +static const char invparity[256] = { + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0, + 1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1 +}; + +/* + * bitsperbyte contains the number of bits per byte + * this is only used for testing and repairing parity + * (a precalculated value slightly improves performance) + */ +static const char bitsperbyte[256] = { + 0, 1, 1, 2, 1, 2, 2, 3, 1, 2, 2, 3, 2, 3, 3, 4, + 1, 2, 2, 3, 2, 3, 3, 4, 2, 3, 3, 4, 3, 4, 4, 5, + 1, 2, 2, 3, 2, 3, 3, 4, 2, 3, 3, 4, 3, 4, 4, 5, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 1, 2, 2, 3, 2, 3, 3, 4, 2, 3, 3, 4, 3, 4, 4, 5, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 3, 4, 4, 5, 4, 5, 5, 6, 4, 5, 5, 6, 5, 6, 6, 7, + 1, 2, 2, 3, 2, 3, 3, 4, 2, 3, 3, 4, 3, 4, 4, 5, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 3, 4, 4, 5, 4, 5, 5, 6, 4, 5, 5, 6, 5, 6, 6, 7, + 2, 3, 3, 4, 3, 4, 4, 5, 3, 4, 4, 5, 4, 5, 5, 6, + 3, 4, 4, 5, 4, 5, 5, 6, 4, 5, 5, 6, 5, 6, 6, 7, + 3, 4, 4, 5, 4, 5, 5, 6, 4, 5, 5, 6, 5, 6, 6, 7, + 4, 5, 5, 6, 5, 6, 6, 7, 5, 6, 6, 7, 6, 7, 7, 8, +}; + +/* + * addressbits is a lookup table to filter out the bits from the xor-ed + * ECC data that identify the faulty location. + * this is only used for repairing parity + * see the comments in nand_correct_data for more details + */ +static const char addressbits[256] = { + 0x00, 0x00, 0x01, 0x01, 0x00, 0x00, 0x01, 0x01, + 0x02, 0x02, 0x03, 0x03, 0x02, 0x02, 0x03, 0x03, + 0x00, 0x00, 0x01, 0x01, 0x00, 0x00, 0x01, 0x01, + 0x02, 0x02, 0x03, 0x03, 0x02, 0x02, 0x03, 0x03, + 0x04, 0x04, 0x05, 0x05, 0x04, 0x04, 0x05, 0x05, + 0x06, 0x06, 0x07, 0x07, 0x06, 0x06, 0x07, 0x07, + 0x04, 0x04, 0x05, 0x05, 0x04, 0x04, 0x05, 0x05, + 0x06, 0x06, 0x07, 0x07, 0x06, 0x06, 0x07, 0x07, + 0x00, 0x00, 0x01, 0x01, 0x00, 0x00, 0x01, 0x01, + 0x02, 0x02, 0x03, 0x03, 0x02, 0x02, 0x03, 0x03, + 0x00, 0x00, 0x01, 0x01, 0x00, 0x00, 0x01, 0x01, + 0x02, 0x02, 0x03, 0x03, 0x02, 0x02, 0x03, 0x03, + 0x04, 0x04, 0x05, 0x05, 0x04, 0x04, 0x05, 0x05, + 0x06, 0x06, 0x07, 0x07, 0x06, 0x06, 0x07, 0x07, + 0x04, 0x04, 0x05, 0x05, 0x04, 0x04, 0x05, 0x05, + 0x06, 0x06, 0x07, 0x07, 0x06, 0x06, 0x07, 0x07, + 0x08, 0x08, 0x09, 0x09, 0x08, 0x08, 0x09, 0x09, + 0x0a, 0x0a, 0x0b, 0x0b, 0x0a, 0x0a, 0x0b, 0x0b, + 0x08, 0x08, 0x09, 0x09, 0x08, 0x08, 0x09, 0x09, + 0x0a, 0x0a, 0x0b, 0x0b, 0x0a, 0x0a, 0x0b, 0x0b, + 0x0c, 0x0c, 0x0d, 0x0d, 0x0c, 0x0c, 0x0d, 0x0d, + 0x0e, 0x0e, 0x0f, 0x0f, 0x0e, 0x0e, 0x0f, 0x0f, + 0x0c, 0x0c, 0x0d, 0x0d, 0x0c, 0x0c, 0x0d, 0x0d, + 0x0e, 0x0e, 0x0f, 0x0f, 0x0e, 0x0e, 0x0f, 0x0f, + 0x08, 0x08, 0x09, 0x09, 0x08, 0x08, 0x09, 0x09, + 0x0a, 0x0a, 0x0b, 0x0b, 0x0a, 0x0a, 0x0b, 0x0b, + 0x08, 0x08, 0x09, 0x09, 0x08, 0x08, 0x09, 0x09, + 0x0a, 0x0a, 0x0b, 0x0b, 0x0a, 0x0a, 0x0b, 0x0b, + 0x0c, 0x0c, 0x0d, 0x0d, 0x0c, 0x0c, 0x0d, 0x0d, + 0x0e, 0x0e, 0x0f, 0x0f, 0x0e, 0x0e, 0x0f, 0x0f, + 0x0c, 0x0c, 0x0d, 0x0d, 0x0c, 0x0c, 0x0d, 0x0d, + 0x0e, 0x0e, 0x0f, 0x0f, 0x0e, 0x0e, 0x0f, 0x0f +}; + +/** + * __nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte + * block + * @buf: input buffer with raw data + * @eccsize: data bytes per ECC step (256 or 512) + * @code: output buffer with ECC + */ +void __nand_calculate_ecc(const unsigned char *buf, unsigned int eccsize, + unsigned char *code) +{ + int i; + const uint32_t *bp = (uint32_t *)buf; + /* 256 or 512 bytes/ecc */ + const uint32_t eccsize_mult = eccsize >> 8; + uint32_t cur; /* current value in buffer */ + /* rp0..rp15..rp17 are the various accumulated parities (per byte) */ + uint32_t rp0, rp1, rp2, rp3, rp4, rp5, rp6, rp7; + uint32_t rp8, rp9, rp10, rp11, rp12, rp13, rp14, rp15, rp16; + uint32_t uninitialized_var(rp17); /* to make compiler happy */ + uint32_t par; /* the cumulative parity for all data */ + uint32_t tmppar; /* the cumulative parity for this iteration; + for rp12, rp14 and rp16 at the end of the + loop */ + + par = 0; + rp4 = 0; + rp6 = 0; + rp8 = 0; + rp10 = 0; + rp12 = 0; + rp14 = 0; + rp16 = 0; + + /* + * The loop is unrolled a number of times; + * This avoids if statements to decide on which rp value to update + * Also we process the data by longwords. + * Note: passing unaligned data might give a performance penalty. + * It is assumed that the buffers are aligned. + * tmppar is the cumulative sum of this iteration. + * needed for calculating rp12, rp14, rp16 and par + * also used as a performance improvement for rp6, rp8 and rp10 + */ + for (i = 0; i < eccsize_mult << 2; i++) { + cur = *bp++; + tmppar = cur; + rp4 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp6 ^= tmppar; + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp8 ^= tmppar; + + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + rp6 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp6 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp10 ^= tmppar; + + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + rp6 ^= cur; + rp8 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp6 ^= cur; + rp8 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + rp8 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp8 ^= cur; + + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + rp6 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp6 ^= cur; + cur = *bp++; + tmppar ^= cur; + rp4 ^= cur; + cur = *bp++; + tmppar ^= cur; + + par ^= tmppar; + if ((i & 0x1) == 0) + rp12 ^= tmppar; + if ((i & 0x2) == 0) + rp14 ^= tmppar; + if (eccsize_mult == 2 && (i & 0x4) == 0) + rp16 ^= tmppar; + } + + /* + * handle the fact that we use longword operations + * we'll bring rp4..rp14..rp16 back to single byte entities by + * shifting and xoring first fold the upper and lower 16 bits, + * then the upper and lower 8 bits. + */ + rp4 ^= (rp4 >> 16); + rp4 ^= (rp4 >> 8); + rp4 &= 0xff; + rp6 ^= (rp6 >> 16); + rp6 ^= (rp6 >> 8); + rp6 &= 0xff; + rp8 ^= (rp8 >> 16); + rp8 ^= (rp8 >> 8); + rp8 &= 0xff; + rp10 ^= (rp10 >> 16); + rp10 ^= (rp10 >> 8); + rp10 &= 0xff; + rp12 ^= (rp12 >> 16); + rp12 ^= (rp12 >> 8); + rp12 &= 0xff; + rp14 ^= (rp14 >> 16); + rp14 ^= (rp14 >> 8); + rp14 &= 0xff; + if (eccsize_mult == 2) { + rp16 ^= (rp16 >> 16); + rp16 ^= (rp16 >> 8); + rp16 &= 0xff; + } + + /* + * we also need to calculate the row parity for rp0..rp3 + * This is present in par, because par is now + * rp3 rp3 rp2 rp2 in little endian and + * rp2 rp2 rp3 rp3 in big endian + * as well as + * rp1 rp0 rp1 rp0 in little endian and + * rp0 rp1 rp0 rp1 in big endian + * First calculate rp2 and rp3 + */ +#ifdef __BIG_ENDIAN + rp2 = (par >> 16); + rp2 ^= (rp2 >> 8); + rp2 &= 0xff; + rp3 = par & 0xffff; + rp3 ^= (rp3 >> 8); + rp3 &= 0xff; +#else + rp3 = (par >> 16); + rp3 ^= (rp3 >> 8); + rp3 &= 0xff; + rp2 = par & 0xffff; + rp2 ^= (rp2 >> 8); + rp2 &= 0xff; +#endif + + /* reduce par to 16 bits then calculate rp1 and rp0 */ + par ^= (par >> 16); +#ifdef __BIG_ENDIAN + rp0 = (par >> 8) & 0xff; + rp1 = (par & 0xff); +#else + rp1 = (par >> 8) & 0xff; + rp0 = (par & 0xff); +#endif + + /* finally reduce par to 8 bits */ + par ^= (par >> 8); + par &= 0xff; + + /* + * and calculate rp5..rp15..rp17 + * note that par = rp4 ^ rp5 and due to the commutative property + * of the ^ operator we can say: + * rp5 = (par ^ rp4); + * The & 0xff seems superfluous, but benchmarking learned that + * leaving it out gives slightly worse results. No idea why, probably + * it has to do with the way the pipeline in pentium is organized. + */ + rp5 = (par ^ rp4) & 0xff; + rp7 = (par ^ rp6) & 0xff; + rp9 = (par ^ rp8) & 0xff; + rp11 = (par ^ rp10) & 0xff; + rp13 = (par ^ rp12) & 0xff; + rp15 = (par ^ rp14) & 0xff; + if (eccsize_mult == 2) + rp17 = (par ^ rp16) & 0xff; + + /* + * Finally calculate the ECC bits. + * Again here it might seem that there are performance optimisations + * possible, but benchmarks showed that on the system this is developed + * the code below is the fastest + */ +#ifdef CONFIG_MTD_NAND_ECC_SMC + code[0] = + (invparity[rp7] << 7) | + (invparity[rp6] << 6) | + (invparity[rp5] << 5) | + (invparity[rp4] << 4) | + (invparity[rp3] << 3) | + (invparity[rp2] << 2) | + (invparity[rp1] << 1) | + (invparity[rp0]); + code[1] = + (invparity[rp15] << 7) | + (invparity[rp14] << 6) | + (invparity[rp13] << 5) | + (invparity[rp12] << 4) | + (invparity[rp11] << 3) | + (invparity[rp10] << 2) | + (invparity[rp9] << 1) | + (invparity[rp8]); +#else + code[1] = + (invparity[rp7] << 7) | + (invparity[rp6] << 6) | + (invparity[rp5] << 5) | + (invparity[rp4] << 4) | + (invparity[rp3] << 3) | + (invparity[rp2] << 2) | + (invparity[rp1] << 1) | + (invparity[rp0]); + code[0] = + (invparity[rp15] << 7) | + (invparity[rp14] << 6) | + (invparity[rp13] << 5) | + (invparity[rp12] << 4) | + (invparity[rp11] << 3) | + (invparity[rp10] << 2) | + (invparity[rp9] << 1) | + (invparity[rp8]); +#endif + if (eccsize_mult == 1) + code[2] = + (invparity[par & 0xf0] << 7) | + (invparity[par & 0x0f] << 6) | + (invparity[par & 0xcc] << 5) | + (invparity[par & 0x33] << 4) | + (invparity[par & 0xaa] << 3) | + (invparity[par & 0x55] << 2) | + 3; + else + code[2] = + (invparity[par & 0xf0] << 7) | + (invparity[par & 0x0f] << 6) | + (invparity[par & 0xcc] << 5) | + (invparity[par & 0x33] << 4) | + (invparity[par & 0xaa] << 3) | + (invparity[par & 0x55] << 2) | + (invparity[rp17] << 1) | + (invparity[rp16] << 0); +} +EXPORT_SYMBOL(__nand_calculate_ecc); + +/** + * nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte + * block + * @mtd: MTD block structure + * @buf: input buffer with raw data + * @code: output buffer with ECC + */ +int nand_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf, + unsigned char *code) +{ + __nand_calculate_ecc(buf, + ((struct nand_chip *)mtd->priv)->ecc.size, code); + + return 0; +} +EXPORT_SYMBOL(nand_calculate_ecc); + +/** + * __nand_correct_data - [NAND Interface] Detect and correct bit error(s) + * @buf: raw data read from the chip + * @read_ecc: ECC from the chip + * @calc_ecc: the ECC calculated from raw data + * @eccsize: data bytes per ECC step (256 or 512) + * + * Detect and correct a 1 bit error for eccsize byte block + */ +int __nand_correct_data(unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc, + unsigned int eccsize) +{ + unsigned char b0, b1, b2, bit_addr; + unsigned int byte_addr; + /* 256 or 512 bytes/ecc */ + const uint32_t eccsize_mult = eccsize >> 8; + + /* + * b0 to b2 indicate which bit is faulty (if any) + * we might need the xor result more than once, + * so keep them in a local var + */ +#ifdef CONFIG_MTD_NAND_ECC_SMC + b0 = read_ecc[0] ^ calc_ecc[0]; + b1 = read_ecc[1] ^ calc_ecc[1]; +#else + b0 = read_ecc[1] ^ calc_ecc[1]; + b1 = read_ecc[0] ^ calc_ecc[0]; +#endif + b2 = read_ecc[2] ^ calc_ecc[2]; + + /* check if there are any bitfaults */ + + /* repeated if statements are slightly more efficient than switch ... */ + /* ordered in order of likelihood */ + + if ((b0 | b1 | b2) == 0) + return 0; /* no error */ + + if ((((b0 ^ (b0 >> 1)) & 0x55) == 0x55) && + (((b1 ^ (b1 >> 1)) & 0x55) == 0x55) && + ((eccsize_mult == 1 && ((b2 ^ (b2 >> 1)) & 0x54) == 0x54) || + (eccsize_mult == 2 && ((b2 ^ (b2 >> 1)) & 0x55) == 0x55))) { + /* single bit error */ + /* + * rp17/rp15/13/11/9/7/5/3/1 indicate which byte is the faulty + * byte, cp 5/3/1 indicate the faulty bit. + * A lookup table (called addressbits) is used to filter + * the bits from the byte they are in. + * A marginal optimisation is possible by having three + * different lookup tables. + * One as we have now (for b0), one for b2 + * (that would avoid the >> 1), and one for b1 (with all values + * << 4). However it was felt that introducing two more tables + * hardly justify the gain. + * + * The b2 shift is there to get rid of the lowest two bits. + * We could also do addressbits[b2] >> 1 but for the + * performance it does not make any difference + */ + if (eccsize_mult == 1) + byte_addr = (addressbits[b1] << 4) + addressbits[b0]; + else + byte_addr = (addressbits[b2 & 0x3] << 8) + + (addressbits[b1] << 4) + addressbits[b0]; + bit_addr = addressbits[b2 >> 2]; + /* flip the bit */ + buf[byte_addr] ^= (1 << bit_addr); + return 1; + + } + /* count nr of bits; use table lookup, faster than calculating it */ + if ((bitsperbyte[b0] + bitsperbyte[b1] + bitsperbyte[b2]) == 1) + return 1; /* error in ECC data; no action needed */ + + pr_err("%s: uncorrectable ECC error\n", __func__); + return -1; +} +EXPORT_SYMBOL(__nand_correct_data); + +/** + * nand_correct_data - [NAND Interface] Detect and correct bit error(s) + * @mtd: MTD block structure + * @buf: raw data read from the chip + * @read_ecc: ECC from the chip + * @calc_ecc: the ECC calculated from raw data + * + * Detect and correct a 1 bit error for 256/512 byte block + */ +int nand_correct_data(struct mtd_info *mtd, unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc) +{ + return __nand_correct_data(buf, read_ecc, calc_ecc, + ((struct nand_chip *)mtd->priv)->ecc.size); +} +EXPORT_SYMBOL(nand_correct_data); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Frans Meulenbroeks <fransmeulenbroeks@gmail.com>"); +MODULE_DESCRIPTION("Generic NAND ECC support"); diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c new file mode 100644 index 000000000..dd620c19c --- /dev/null +++ b/drivers/mtd/nand/nand_ids.c @@ -0,0 +1,190 @@ +/* + * drivers/mtd/nandids.c + * + * Copyright (C) 2002 Thomas Gleixner (tglx@linutronix.de) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#include <linux/module.h> +#include <linux/mtd/nand.h> +#include <linux/sizes.h> + +#define LP_OPTIONS NAND_SAMSUNG_LP_OPTIONS +#define LP_OPTIONS16 (LP_OPTIONS | NAND_BUSWIDTH_16) + +#define SP_OPTIONS NAND_NEED_READRDY +#define SP_OPTIONS16 (SP_OPTIONS | NAND_BUSWIDTH_16) + +/* + * The chip ID list: + * name, device ID, page size, chip size in MiB, eraseblock size, options + * + * If page size and eraseblock size are 0, the sizes are taken from the + * extended chip ID. + */ +struct nand_flash_dev nand_flash_ids[] = { + /* + * Some incompatible NAND chips share device ID's and so must be + * listed by full ID. We list them first so that we can easily identify + * the most specific match. + */ + {"TC58NVG2S0F 4G 3.3V 8-bit", + { .id = {0x98, 0xdc, 0x90, 0x26, 0x76, 0x15, 0x01, 0x08} }, + SZ_4K, SZ_512, SZ_256K, 0, 8, 224, NAND_ECC_INFO(4, SZ_512) }, + {"TC58NVG3S0F 8G 3.3V 8-bit", + { .id = {0x98, 0xd3, 0x90, 0x26, 0x76, 0x15, 0x02, 0x08} }, + SZ_4K, SZ_1K, SZ_256K, 0, 8, 232, NAND_ECC_INFO(4, SZ_512) }, + {"TC58NVG5D2 32G 3.3V 8-bit", + { .id = {0x98, 0xd7, 0x94, 0x32, 0x76, 0x56, 0x09, 0x00} }, + SZ_8K, SZ_4K, SZ_1M, 0, 8, 640, NAND_ECC_INFO(40, SZ_1K) }, + {"TC58NVG6D2 64G 3.3V 8-bit", + { .id = {0x98, 0xde, 0x94, 0x82, 0x76, 0x56, 0x04, 0x20} }, + SZ_8K, SZ_8K, SZ_2M, 0, 8, 640, NAND_ECC_INFO(40, SZ_1K) }, + {"SDTNRGAMA 64G 3.3V 8-bit", + { .id = {0x45, 0xde, 0x94, 0x93, 0x76, 0x50} }, + SZ_16K, SZ_8K, SZ_4M, 0, 6, 1280, NAND_ECC_INFO(40, SZ_1K) }, + {"H27UCG8T2ATR-BC 64G 3.3V 8-bit", + { .id = {0xad, 0xde, 0x94, 0xda, 0x74, 0xc4} }, + SZ_8K, SZ_8K, SZ_2M, 0, 6, 640, NAND_ECC_INFO(40, SZ_1K), + 4 }, + + LEGACY_ID_NAND("NAND 4MiB 5V 8-bit", 0x6B, 4, SZ_8K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE3, 4, SZ_8K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE5, 4, SZ_8K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 8MiB 3,3V 8-bit", 0xD6, 8, SZ_8K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 8MiB 3,3V 8-bit", 0xE6, 8, SZ_8K, SP_OPTIONS), + + LEGACY_ID_NAND("NAND 16MiB 1,8V 8-bit", 0x33, 16, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 16MiB 3,3V 8-bit", 0x73, 16, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 16MiB 1,8V 16-bit", 0x43, 16, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 16MiB 3,3V 16-bit", 0x53, 16, SZ_16K, SP_OPTIONS16), + + LEGACY_ID_NAND("NAND 32MiB 1,8V 8-bit", 0x35, 32, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 32MiB 3,3V 8-bit", 0x75, 32, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 32MiB 1,8V 16-bit", 0x45, 32, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 32MiB 3,3V 16-bit", 0x55, 32, SZ_16K, SP_OPTIONS16), + + LEGACY_ID_NAND("NAND 64MiB 1,8V 8-bit", 0x36, 64, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 64MiB 3,3V 8-bit", 0x76, 64, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 64MiB 1,8V 16-bit", 0x46, 64, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 64MiB 3,3V 16-bit", 0x56, 64, SZ_16K, SP_OPTIONS16), + + LEGACY_ID_NAND("NAND 128MiB 1,8V 8-bit", 0x78, 128, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 128MiB 1,8V 8-bit", 0x39, 128, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 128MiB 3,3V 8-bit", 0x79, 128, SZ_16K, SP_OPTIONS), + LEGACY_ID_NAND("NAND 128MiB 1,8V 16-bit", 0x72, 128, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 128MiB 1,8V 16-bit", 0x49, 128, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 128MiB 3,3V 16-bit", 0x74, 128, SZ_16K, SP_OPTIONS16), + LEGACY_ID_NAND("NAND 128MiB 3,3V 16-bit", 0x59, 128, SZ_16K, SP_OPTIONS16), + + LEGACY_ID_NAND("NAND 256MiB 3,3V 8-bit", 0x71, 256, SZ_16K, SP_OPTIONS), + + /* + * These are the new chips with large page size. Their page size and + * eraseblock size are determined from the extended ID bytes. + */ + + /* 512 Megabit */ + EXTENDED_ID_NAND("NAND 64MiB 1,8V 8-bit", 0xA2, 64, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64MiB 1,8V 8-bit", 0xA0, 64, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64MiB 3,3V 8-bit", 0xF2, 64, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64MiB 3,3V 8-bit", 0xD0, 64, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64MiB 3,3V 8-bit", 0xF0, 64, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64MiB 1,8V 16-bit", 0xB2, 64, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 64MiB 1,8V 16-bit", 0xB0, 64, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 64MiB 3,3V 16-bit", 0xC2, 64, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 64MiB 3,3V 16-bit", 0xC0, 64, LP_OPTIONS16), + + /* 1 Gigabit */ + EXTENDED_ID_NAND("NAND 128MiB 1,8V 8-bit", 0xA1, 128, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 128MiB 3,3V 8-bit", 0xF1, 128, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 128MiB 3,3V 8-bit", 0xD1, 128, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 128MiB 1,8V 16-bit", 0xB1, 128, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 128MiB 3,3V 16-bit", 0xC1, 128, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 128MiB 1,8V 16-bit", 0xAD, 128, LP_OPTIONS16), + + /* 2 Gigabit */ + EXTENDED_ID_NAND("NAND 256MiB 1,8V 8-bit", 0xAA, 256, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 256MiB 3,3V 8-bit", 0xDA, 256, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 256MiB 1,8V 16-bit", 0xBA, 256, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 256MiB 3,3V 16-bit", 0xCA, 256, LP_OPTIONS16), + + /* 4 Gigabit */ + EXTENDED_ID_NAND("NAND 512MiB 1,8V 8-bit", 0xAC, 512, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 512MiB 3,3V 8-bit", 0xDC, 512, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 512MiB 1,8V 16-bit", 0xBC, 512, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 512MiB 3,3V 16-bit", 0xCC, 512, LP_OPTIONS16), + + /* 8 Gigabit */ + EXTENDED_ID_NAND("NAND 1GiB 1,8V 8-bit", 0xA3, 1024, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 1GiB 3,3V 8-bit", 0xD3, 1024, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 1GiB 1,8V 16-bit", 0xB3, 1024, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 1GiB 3,3V 16-bit", 0xC3, 1024, LP_OPTIONS16), + + /* 16 Gigabit */ + EXTENDED_ID_NAND("NAND 2GiB 1,8V 8-bit", 0xA5, 2048, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 2GiB 3,3V 8-bit", 0xD5, 2048, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 2GiB 1,8V 16-bit", 0xB5, 2048, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 2GiB 3,3V 16-bit", 0xC5, 2048, LP_OPTIONS16), + + /* 32 Gigabit */ + EXTENDED_ID_NAND("NAND 4GiB 1,8V 8-bit", 0xA7, 4096, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 4GiB 3,3V 8-bit", 0xD7, 4096, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 4GiB 1,8V 16-bit", 0xB7, 4096, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 4GiB 3,3V 16-bit", 0xC7, 4096, LP_OPTIONS16), + + /* 64 Gigabit */ + EXTENDED_ID_NAND("NAND 8GiB 1,8V 8-bit", 0xAE, 8192, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 8GiB 3,3V 8-bit", 0xDE, 8192, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 8GiB 1,8V 16-bit", 0xBE, 8192, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 8GiB 3,3V 16-bit", 0xCE, 8192, LP_OPTIONS16), + + /* 128 Gigabit */ + EXTENDED_ID_NAND("NAND 16GiB 1,8V 8-bit", 0x1A, 16384, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 16GiB 3,3V 8-bit", 0x3A, 16384, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 16GiB 1,8V 16-bit", 0x2A, 16384, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 16GiB 3,3V 16-bit", 0x4A, 16384, LP_OPTIONS16), + + /* 256 Gigabit */ + EXTENDED_ID_NAND("NAND 32GiB 1,8V 8-bit", 0x1C, 32768, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 32GiB 3,3V 8-bit", 0x3C, 32768, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 32GiB 1,8V 16-bit", 0x2C, 32768, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 32GiB 3,3V 16-bit", 0x4C, 32768, LP_OPTIONS16), + + /* 512 Gigabit */ + EXTENDED_ID_NAND("NAND 64GiB 1,8V 8-bit", 0x1E, 65536, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64GiB 3,3V 8-bit", 0x3E, 65536, LP_OPTIONS), + EXTENDED_ID_NAND("NAND 64GiB 1,8V 16-bit", 0x2E, 65536, LP_OPTIONS16), + EXTENDED_ID_NAND("NAND 64GiB 3,3V 16-bit", 0x4E, 65536, LP_OPTIONS16), + + {NULL} +}; + +/* Manufacturer IDs */ +struct nand_manufacturers nand_manuf_ids[] = { + {NAND_MFR_TOSHIBA, "Toshiba"}, + {NAND_MFR_SAMSUNG, "Samsung"}, + {NAND_MFR_FUJITSU, "Fujitsu"}, + {NAND_MFR_NATIONAL, "National"}, + {NAND_MFR_RENESAS, "Renesas"}, + {NAND_MFR_STMICRO, "ST Micro"}, + {NAND_MFR_HYNIX, "Hynix"}, + {NAND_MFR_MICRON, "Micron"}, + {NAND_MFR_AMD, "AMD/Spansion"}, + {NAND_MFR_MACRONIX, "Macronix"}, + {NAND_MFR_EON, "Eon"}, + {NAND_MFR_SANDISK, "SanDisk"}, + {NAND_MFR_INTEL, "Intel"}, + {NAND_MFR_ATO, "ATO"}, + {0x0, "Unknown"} +}; + +EXPORT_SYMBOL(nand_manuf_ids); +EXPORT_SYMBOL(nand_flash_ids); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>"); +MODULE_DESCRIPTION("Nand device & manufacturer IDs"); diff --git a/drivers/mtd/nand/nand_timings.c b/drivers/mtd/nand/nand_timings.c new file mode 100644 index 000000000..e81470a8a --- /dev/null +++ b/drivers/mtd/nand/nand_timings.c @@ -0,0 +1,253 @@ +/* + * Copyright (C) 2014 Free Electrons + * + * Author: Boris BREZILLON <boris.brezillon@free-electrons.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#include <linux/kernel.h> +#include <linux/err.h> +#include <linux/export.h> +#include <linux/mtd/nand.h> + +static const struct nand_sdr_timings onfi_sdr_timings[] = { + /* Mode 0 */ + { + .tADL_min = 200000, + .tALH_min = 20000, + .tALS_min = 50000, + .tAR_min = 25000, + .tCEA_max = 100000, + .tCEH_min = 20000, + .tCH_min = 20000, + .tCHZ_max = 100000, + .tCLH_min = 20000, + .tCLR_min = 20000, + .tCLS_min = 50000, + .tCOH_min = 0, + .tCS_min = 70000, + .tDH_min = 20000, + .tDS_min = 40000, + .tFEAT_max = 1000000, + .tIR_min = 10000, + .tITC_max = 1000000, + .tRC_min = 100000, + .tREA_max = 40000, + .tREH_min = 30000, + .tRHOH_min = 0, + .tRHW_min = 200000, + .tRHZ_max = 200000, + .tRLOH_min = 0, + .tRP_min = 50000, + .tRST_max = 250000000000ULL, + .tWB_max = 200000, + .tRR_min = 40000, + .tWC_min = 100000, + .tWH_min = 30000, + .tWHR_min = 120000, + .tWP_min = 50000, + .tWW_min = 100000, + }, + /* Mode 1 */ + { + .tADL_min = 100000, + .tALH_min = 10000, + .tALS_min = 25000, + .tAR_min = 10000, + .tCEA_max = 45000, + .tCEH_min = 20000, + .tCH_min = 10000, + .tCHZ_max = 50000, + .tCLH_min = 10000, + .tCLR_min = 10000, + .tCLS_min = 25000, + .tCOH_min = 15000, + .tCS_min = 35000, + .tDH_min = 10000, + .tDS_min = 20000, + .tFEAT_max = 1000000, + .tIR_min = 0, + .tITC_max = 1000000, + .tRC_min = 50000, + .tREA_max = 30000, + .tREH_min = 15000, + .tRHOH_min = 15000, + .tRHW_min = 100000, + .tRHZ_max = 100000, + .tRLOH_min = 0, + .tRP_min = 25000, + .tRR_min = 20000, + .tRST_max = 500000000, + .tWB_max = 100000, + .tWC_min = 45000, + .tWH_min = 15000, + .tWHR_min = 80000, + .tWP_min = 25000, + .tWW_min = 100000, + }, + /* Mode 2 */ + { + .tADL_min = 100000, + .tALH_min = 10000, + .tALS_min = 15000, + .tAR_min = 10000, + .tCEA_max = 30000, + .tCEH_min = 20000, + .tCH_min = 10000, + .tCHZ_max = 50000, + .tCLH_min = 10000, + .tCLR_min = 10000, + .tCLS_min = 15000, + .tCOH_min = 15000, + .tCS_min = 25000, + .tDH_min = 5000, + .tDS_min = 15000, + .tFEAT_max = 1000000, + .tIR_min = 0, + .tITC_max = 1000000, + .tRC_min = 35000, + .tREA_max = 25000, + .tREH_min = 15000, + .tRHOH_min = 15000, + .tRHW_min = 100000, + .tRHZ_max = 100000, + .tRLOH_min = 0, + .tRR_min = 20000, + .tRST_max = 500000000, + .tWB_max = 100000, + .tRP_min = 17000, + .tWC_min = 35000, + .tWH_min = 15000, + .tWHR_min = 80000, + .tWP_min = 17000, + .tWW_min = 100000, + }, + /* Mode 3 */ + { + .tADL_min = 100000, + .tALH_min = 5000, + .tALS_min = 10000, + .tAR_min = 10000, + .tCEA_max = 25000, + .tCEH_min = 20000, + .tCH_min = 5000, + .tCHZ_max = 50000, + .tCLH_min = 5000, + .tCLR_min = 10000, + .tCLS_min = 10000, + .tCOH_min = 15000, + .tCS_min = 25000, + .tDH_min = 5000, + .tDS_min = 10000, + .tFEAT_max = 1000000, + .tIR_min = 0, + .tITC_max = 1000000, + .tRC_min = 30000, + .tREA_max = 20000, + .tREH_min = 10000, + .tRHOH_min = 15000, + .tRHW_min = 100000, + .tRHZ_max = 100000, + .tRLOH_min = 0, + .tRP_min = 15000, + .tRR_min = 20000, + .tRST_max = 500000000, + .tWB_max = 100000, + .tWC_min = 30000, + .tWH_min = 10000, + .tWHR_min = 80000, + .tWP_min = 15000, + .tWW_min = 100000, + }, + /* Mode 4 */ + { + .tADL_min = 70000, + .tALH_min = 5000, + .tALS_min = 10000, + .tAR_min = 10000, + .tCEA_max = 25000, + .tCEH_min = 20000, + .tCH_min = 5000, + .tCHZ_max = 30000, + .tCLH_min = 5000, + .tCLR_min = 10000, + .tCLS_min = 10000, + .tCOH_min = 15000, + .tCS_min = 20000, + .tDH_min = 5000, + .tDS_min = 10000, + .tFEAT_max = 1000000, + .tIR_min = 0, + .tITC_max = 1000000, + .tRC_min = 25000, + .tREA_max = 20000, + .tREH_min = 10000, + .tRHOH_min = 15000, + .tRHW_min = 100000, + .tRHZ_max = 100000, + .tRLOH_min = 5000, + .tRP_min = 12000, + .tRR_min = 20000, + .tRST_max = 500000000, + .tWB_max = 100000, + .tWC_min = 25000, + .tWH_min = 10000, + .tWHR_min = 80000, + .tWP_min = 12000, + .tWW_min = 100000, + }, + /* Mode 5 */ + { + .tADL_min = 70000, + .tALH_min = 5000, + .tALS_min = 10000, + .tAR_min = 10000, + .tCEA_max = 25000, + .tCEH_min = 20000, + .tCH_min = 5000, + .tCHZ_max = 30000, + .tCLH_min = 5000, + .tCLR_min = 10000, + .tCLS_min = 10000, + .tCOH_min = 15000, + .tCS_min = 15000, + .tDH_min = 5000, + .tDS_min = 7000, + .tFEAT_max = 1000000, + .tIR_min = 0, + .tITC_max = 1000000, + .tRC_min = 20000, + .tREA_max = 16000, + .tREH_min = 7000, + .tRHOH_min = 15000, + .tRHW_min = 100000, + .tRHZ_max = 100000, + .tRLOH_min = 5000, + .tRP_min = 10000, + .tRR_min = 20000, + .tRST_max = 500000000, + .tWB_max = 100000, + .tWC_min = 20000, + .tWH_min = 7000, + .tWHR_min = 80000, + .tWP_min = 10000, + .tWW_min = 100000, + }, +}; + +/** + * onfi_async_timing_mode_to_sdr_timings - [NAND Interface] Retrieve NAND + * timings according to the given ONFI timing mode + * @mode: ONFI timing mode + */ +const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode) +{ + if (mode < 0 || mode >= ARRAY_SIZE(onfi_sdr_timings)) + return ERR_PTR(-EINVAL); + + return &onfi_sdr_timings[mode]; +} +EXPORT_SYMBOL(onfi_async_timing_mode_to_sdr_timings); diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c new file mode 100644 index 000000000..f2324271b --- /dev/null +++ b/drivers/mtd/nand/nandsim.c @@ -0,0 +1,2425 @@ +/* + * NAND flash simulator. + * + * Author: Artem B. Bityuckiy <dedekind@oktetlabs.ru>, <dedekind@infradead.org> + * + * Copyright (C) 2004 Nokia Corporation + * + * Note: NS means "NAND Simulator". + * Note: Input means input TO flash chip, output means output FROM chip. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any later + * version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General + * Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA + */ + +#include <linux/init.h> +#include <linux/types.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/vmalloc.h> +#include <linux/math64.h> +#include <linux/slab.h> +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_bch.h> +#include <linux/mtd/partitions.h> +#include <linux/delay.h> +#include <linux/list.h> +#include <linux/random.h> +#include <linux/sched.h> +#include <linux/fs.h> +#include <linux/pagemap.h> +#include <linux/seq_file.h> +#include <linux/debugfs.h> + +/* Default simulator parameters values */ +#if !defined(CONFIG_NANDSIM_FIRST_ID_BYTE) || \ + !defined(CONFIG_NANDSIM_SECOND_ID_BYTE) || \ + !defined(CONFIG_NANDSIM_THIRD_ID_BYTE) || \ + !defined(CONFIG_NANDSIM_FOURTH_ID_BYTE) +#define CONFIG_NANDSIM_FIRST_ID_BYTE 0x98 +#define CONFIG_NANDSIM_SECOND_ID_BYTE 0x39 +#define CONFIG_NANDSIM_THIRD_ID_BYTE 0xFF /* No byte */ +#define CONFIG_NANDSIM_FOURTH_ID_BYTE 0xFF /* No byte */ +#endif + +#ifndef CONFIG_NANDSIM_ACCESS_DELAY +#define CONFIG_NANDSIM_ACCESS_DELAY 25 +#endif +#ifndef CONFIG_NANDSIM_PROGRAMM_DELAY +#define CONFIG_NANDSIM_PROGRAMM_DELAY 200 +#endif +#ifndef CONFIG_NANDSIM_ERASE_DELAY +#define CONFIG_NANDSIM_ERASE_DELAY 2 +#endif +#ifndef CONFIG_NANDSIM_OUTPUT_CYCLE +#define CONFIG_NANDSIM_OUTPUT_CYCLE 40 +#endif +#ifndef CONFIG_NANDSIM_INPUT_CYCLE +#define CONFIG_NANDSIM_INPUT_CYCLE 50 +#endif +#ifndef CONFIG_NANDSIM_BUS_WIDTH +#define CONFIG_NANDSIM_BUS_WIDTH 8 +#endif +#ifndef CONFIG_NANDSIM_DO_DELAYS +#define CONFIG_NANDSIM_DO_DELAYS 0 +#endif +#ifndef CONFIG_NANDSIM_LOG +#define CONFIG_NANDSIM_LOG 0 +#endif +#ifndef CONFIG_NANDSIM_DBG +#define CONFIG_NANDSIM_DBG 0 +#endif +#ifndef CONFIG_NANDSIM_MAX_PARTS +#define CONFIG_NANDSIM_MAX_PARTS 32 +#endif + +static uint access_delay = CONFIG_NANDSIM_ACCESS_DELAY; +static uint programm_delay = CONFIG_NANDSIM_PROGRAMM_DELAY; +static uint erase_delay = CONFIG_NANDSIM_ERASE_DELAY; +static uint output_cycle = CONFIG_NANDSIM_OUTPUT_CYCLE; +static uint input_cycle = CONFIG_NANDSIM_INPUT_CYCLE; +static uint bus_width = CONFIG_NANDSIM_BUS_WIDTH; +static uint do_delays = CONFIG_NANDSIM_DO_DELAYS; +static uint log = CONFIG_NANDSIM_LOG; +static uint dbg = CONFIG_NANDSIM_DBG; +static unsigned long parts[CONFIG_NANDSIM_MAX_PARTS]; +static unsigned int parts_num; +static char *badblocks = NULL; +static char *weakblocks = NULL; +static char *weakpages = NULL; +static unsigned int bitflips = 0; +static char *gravepages = NULL; +static unsigned int overridesize = 0; +static char *cache_file = NULL; +static unsigned int bbt; +static unsigned int bch; +static u_char id_bytes[8] = { + [0] = CONFIG_NANDSIM_FIRST_ID_BYTE, + [1] = CONFIG_NANDSIM_SECOND_ID_BYTE, + [2] = CONFIG_NANDSIM_THIRD_ID_BYTE, + [3] = CONFIG_NANDSIM_FOURTH_ID_BYTE, + [4 ... 7] = 0xFF, +}; + +module_param_array(id_bytes, byte, NULL, 0400); +module_param_named(first_id_byte, id_bytes[0], byte, 0400); +module_param_named(second_id_byte, id_bytes[1], byte, 0400); +module_param_named(third_id_byte, id_bytes[2], byte, 0400); +module_param_named(fourth_id_byte, id_bytes[3], byte, 0400); +module_param(access_delay, uint, 0400); +module_param(programm_delay, uint, 0400); +module_param(erase_delay, uint, 0400); +module_param(output_cycle, uint, 0400); +module_param(input_cycle, uint, 0400); +module_param(bus_width, uint, 0400); +module_param(do_delays, uint, 0400); +module_param(log, uint, 0400); +module_param(dbg, uint, 0400); +module_param_array(parts, ulong, &parts_num, 0400); +module_param(badblocks, charp, 0400); +module_param(weakblocks, charp, 0400); +module_param(weakpages, charp, 0400); +module_param(bitflips, uint, 0400); +module_param(gravepages, charp, 0400); +module_param(overridesize, uint, 0400); +module_param(cache_file, charp, 0400); +module_param(bbt, uint, 0400); +module_param(bch, uint, 0400); + +MODULE_PARM_DESC(id_bytes, "The ID bytes returned by NAND Flash 'read ID' command"); +MODULE_PARM_DESC(first_id_byte, "The first byte returned by NAND Flash 'read ID' command (manufacturer ID) (obsolete)"); +MODULE_PARM_DESC(second_id_byte, "The second byte returned by NAND Flash 'read ID' command (chip ID) (obsolete)"); +MODULE_PARM_DESC(third_id_byte, "The third byte returned by NAND Flash 'read ID' command (obsolete)"); +MODULE_PARM_DESC(fourth_id_byte, "The fourth byte returned by NAND Flash 'read ID' command (obsolete)"); +MODULE_PARM_DESC(access_delay, "Initial page access delay (microseconds)"); +MODULE_PARM_DESC(programm_delay, "Page programm delay (microseconds"); +MODULE_PARM_DESC(erase_delay, "Sector erase delay (milliseconds)"); +MODULE_PARM_DESC(output_cycle, "Word output (from flash) time (nanoseconds)"); +MODULE_PARM_DESC(input_cycle, "Word input (to flash) time (nanoseconds)"); +MODULE_PARM_DESC(bus_width, "Chip's bus width (8- or 16-bit)"); +MODULE_PARM_DESC(do_delays, "Simulate NAND delays using busy-waits if not zero"); +MODULE_PARM_DESC(log, "Perform logging if not zero"); +MODULE_PARM_DESC(dbg, "Output debug information if not zero"); +MODULE_PARM_DESC(parts, "Partition sizes (in erase blocks) separated by commas"); +/* Page and erase block positions for the following parameters are independent of any partitions */ +MODULE_PARM_DESC(badblocks, "Erase blocks that are initially marked bad, separated by commas"); +MODULE_PARM_DESC(weakblocks, "Weak erase blocks [: remaining erase cycles (defaults to 3)]" + " separated by commas e.g. 113:2 means eb 113" + " can be erased only twice before failing"); +MODULE_PARM_DESC(weakpages, "Weak pages [: maximum writes (defaults to 3)]" + " separated by commas e.g. 1401:2 means page 1401" + " can be written only twice before failing"); +MODULE_PARM_DESC(bitflips, "Maximum number of random bit flips per page (zero by default)"); +MODULE_PARM_DESC(gravepages, "Pages that lose data [: maximum reads (defaults to 3)]" + " separated by commas e.g. 1401:2 means page 1401" + " can be read only twice before failing"); +MODULE_PARM_DESC(overridesize, "Specifies the NAND Flash size overriding the ID bytes. " + "The size is specified in erase blocks and as the exponent of a power of two" + " e.g. 5 means a size of 32 erase blocks"); +MODULE_PARM_DESC(cache_file, "File to use to cache nand pages instead of memory"); +MODULE_PARM_DESC(bbt, "0 OOB, 1 BBT with marker in OOB, 2 BBT with marker in data area"); +MODULE_PARM_DESC(bch, "Enable BCH ecc and set how many bits should " + "be correctable in 512-byte blocks"); + +/* The largest possible page size */ +#define NS_LARGEST_PAGE_SIZE 4096 + +/* The prefix for simulator output */ +#define NS_OUTPUT_PREFIX "[nandsim]" + +/* Simulator's output macros (logging, debugging, warning, error) */ +#define NS_LOG(args...) \ + do { if (log) printk(KERN_DEBUG NS_OUTPUT_PREFIX " log: " args); } while(0) +#define NS_DBG(args...) \ + do { if (dbg) printk(KERN_DEBUG NS_OUTPUT_PREFIX " debug: " args); } while(0) +#define NS_WARN(args...) \ + do { printk(KERN_WARNING NS_OUTPUT_PREFIX " warning: " args); } while(0) +#define NS_ERR(args...) \ + do { printk(KERN_ERR NS_OUTPUT_PREFIX " error: " args); } while(0) +#define NS_INFO(args...) \ + do { printk(KERN_INFO NS_OUTPUT_PREFIX " " args); } while(0) + +/* Busy-wait delay macros (microseconds, milliseconds) */ +#define NS_UDELAY(us) \ + do { if (do_delays) udelay(us); } while(0) +#define NS_MDELAY(us) \ + do { if (do_delays) mdelay(us); } while(0) + +/* Is the nandsim structure initialized ? */ +#define NS_IS_INITIALIZED(ns) ((ns)->geom.totsz != 0) + +/* Good operation completion status */ +#define NS_STATUS_OK(ns) (NAND_STATUS_READY | (NAND_STATUS_WP * ((ns)->lines.wp == 0))) + +/* Operation failed completion status */ +#define NS_STATUS_FAILED(ns) (NAND_STATUS_FAIL | NS_STATUS_OK(ns)) + +/* Calculate the page offset in flash RAM image by (row, column) address */ +#define NS_RAW_OFFSET(ns) \ + (((ns)->regs.row * (ns)->geom.pgszoob) + (ns)->regs.column) + +/* Calculate the OOB offset in flash RAM image by (row, column) address */ +#define NS_RAW_OFFSET_OOB(ns) (NS_RAW_OFFSET(ns) + ns->geom.pgsz) + +/* After a command is input, the simulator goes to one of the following states */ +#define STATE_CMD_READ0 0x00000001 /* read data from the beginning of page */ +#define STATE_CMD_READ1 0x00000002 /* read data from the second half of page */ +#define STATE_CMD_READSTART 0x00000003 /* read data second command (large page devices) */ +#define STATE_CMD_PAGEPROG 0x00000004 /* start page program */ +#define STATE_CMD_READOOB 0x00000005 /* read OOB area */ +#define STATE_CMD_ERASE1 0x00000006 /* sector erase first command */ +#define STATE_CMD_STATUS 0x00000007 /* read status */ +#define STATE_CMD_SEQIN 0x00000009 /* sequential data input */ +#define STATE_CMD_READID 0x0000000A /* read ID */ +#define STATE_CMD_ERASE2 0x0000000B /* sector erase second command */ +#define STATE_CMD_RESET 0x0000000C /* reset */ +#define STATE_CMD_RNDOUT 0x0000000D /* random output command */ +#define STATE_CMD_RNDOUTSTART 0x0000000E /* random output start command */ +#define STATE_CMD_MASK 0x0000000F /* command states mask */ + +/* After an address is input, the simulator goes to one of these states */ +#define STATE_ADDR_PAGE 0x00000010 /* full (row, column) address is accepted */ +#define STATE_ADDR_SEC 0x00000020 /* sector address was accepted */ +#define STATE_ADDR_COLUMN 0x00000030 /* column address was accepted */ +#define STATE_ADDR_ZERO 0x00000040 /* one byte zero address was accepted */ +#define STATE_ADDR_MASK 0x00000070 /* address states mask */ + +/* During data input/output the simulator is in these states */ +#define STATE_DATAIN 0x00000100 /* waiting for data input */ +#define STATE_DATAIN_MASK 0x00000100 /* data input states mask */ + +#define STATE_DATAOUT 0x00001000 /* waiting for page data output */ +#define STATE_DATAOUT_ID 0x00002000 /* waiting for ID bytes output */ +#define STATE_DATAOUT_STATUS 0x00003000 /* waiting for status output */ +#define STATE_DATAOUT_MASK 0x00007000 /* data output states mask */ + +/* Previous operation is done, ready to accept new requests */ +#define STATE_READY 0x00000000 + +/* This state is used to mark that the next state isn't known yet */ +#define STATE_UNKNOWN 0x10000000 + +/* Simulator's actions bit masks */ +#define ACTION_CPY 0x00100000 /* copy page/OOB to the internal buffer */ +#define ACTION_PRGPAGE 0x00200000 /* program the internal buffer to flash */ +#define ACTION_SECERASE 0x00300000 /* erase sector */ +#define ACTION_ZEROOFF 0x00400000 /* don't add any offset to address */ +#define ACTION_HALFOFF 0x00500000 /* add to address half of page */ +#define ACTION_OOBOFF 0x00600000 /* add to address OOB offset */ +#define ACTION_MASK 0x00700000 /* action mask */ + +#define NS_OPER_NUM 13 /* Number of operations supported by the simulator */ +#define NS_OPER_STATES 6 /* Maximum number of states in operation */ + +#define OPT_ANY 0xFFFFFFFF /* any chip supports this operation */ +#define OPT_PAGE512 0x00000002 /* 512-byte page chips */ +#define OPT_PAGE2048 0x00000008 /* 2048-byte page chips */ +#define OPT_PAGE512_8BIT 0x00000040 /* 512-byte page chips with 8-bit bus width */ +#define OPT_PAGE4096 0x00000080 /* 4096-byte page chips */ +#define OPT_LARGEPAGE (OPT_PAGE2048 | OPT_PAGE4096) /* 2048 & 4096-byte page chips */ +#define OPT_SMALLPAGE (OPT_PAGE512) /* 512-byte page chips */ + +/* Remove action bits from state */ +#define NS_STATE(x) ((x) & ~ACTION_MASK) + +/* + * Maximum previous states which need to be saved. Currently saving is + * only needed for page program operation with preceded read command + * (which is only valid for 512-byte pages). + */ +#define NS_MAX_PREVSTATES 1 + +/* Maximum page cache pages needed to read or write a NAND page to the cache_file */ +#define NS_MAX_HELD_PAGES 16 + +struct nandsim_debug_info { + struct dentry *dfs_root; + struct dentry *dfs_wear_report; +}; + +/* + * A union to represent flash memory contents and flash buffer. + */ +union ns_mem { + u_char *byte; /* for byte access */ + uint16_t *word; /* for 16-bit word access */ +}; + +/* + * The structure which describes all the internal simulator data. + */ +struct nandsim { + struct mtd_partition partitions[CONFIG_NANDSIM_MAX_PARTS]; + unsigned int nbparts; + + uint busw; /* flash chip bus width (8 or 16) */ + u_char ids[8]; /* chip's ID bytes */ + uint32_t options; /* chip's characteristic bits */ + uint32_t state; /* current chip state */ + uint32_t nxstate; /* next expected state */ + + uint32_t *op; /* current operation, NULL operations isn't known yet */ + uint32_t pstates[NS_MAX_PREVSTATES]; /* previous states */ + uint16_t npstates; /* number of previous states saved */ + uint16_t stateidx; /* current state index */ + + /* The simulated NAND flash pages array */ + union ns_mem *pages; + + /* Slab allocator for nand pages */ + struct kmem_cache *nand_pages_slab; + + /* Internal buffer of page + OOB size bytes */ + union ns_mem buf; + + /* NAND flash "geometry" */ + struct { + uint64_t totsz; /* total flash size, bytes */ + uint32_t secsz; /* flash sector (erase block) size, bytes */ + uint pgsz; /* NAND flash page size, bytes */ + uint oobsz; /* page OOB area size, bytes */ + uint64_t totszoob; /* total flash size including OOB, bytes */ + uint pgszoob; /* page size including OOB , bytes*/ + uint secszoob; /* sector size including OOB, bytes */ + uint pgnum; /* total number of pages */ + uint pgsec; /* number of pages per sector */ + uint secshift; /* bits number in sector size */ + uint pgshift; /* bits number in page size */ + uint pgaddrbytes; /* bytes per page address */ + uint secaddrbytes; /* bytes per sector address */ + uint idbytes; /* the number ID bytes that this chip outputs */ + } geom; + + /* NAND flash internal registers */ + struct { + unsigned command; /* the command register */ + u_char status; /* the status register */ + uint row; /* the page number */ + uint column; /* the offset within page */ + uint count; /* internal counter */ + uint num; /* number of bytes which must be processed */ + uint off; /* fixed page offset */ + } regs; + + /* NAND flash lines state */ + struct { + int ce; /* chip Enable */ + int cle; /* command Latch Enable */ + int ale; /* address Latch Enable */ + int wp; /* write Protect */ + } lines; + + /* Fields needed when using a cache file */ + struct file *cfile; /* Open file */ + unsigned long *pages_written; /* Which pages have been written */ + void *file_buf; + struct page *held_pages[NS_MAX_HELD_PAGES]; + int held_cnt; + + struct nandsim_debug_info dbg; +}; + +/* + * Operations array. To perform any operation the simulator must pass + * through the correspondent states chain. + */ +static struct nandsim_operations { + uint32_t reqopts; /* options which are required to perform the operation */ + uint32_t states[NS_OPER_STATES]; /* operation's states */ +} ops[NS_OPER_NUM] = { + /* Read page + OOB from the beginning */ + {OPT_SMALLPAGE, {STATE_CMD_READ0 | ACTION_ZEROOFF, STATE_ADDR_PAGE | ACTION_CPY, + STATE_DATAOUT, STATE_READY}}, + /* Read page + OOB from the second half */ + {OPT_PAGE512_8BIT, {STATE_CMD_READ1 | ACTION_HALFOFF, STATE_ADDR_PAGE | ACTION_CPY, + STATE_DATAOUT, STATE_READY}}, + /* Read OOB */ + {OPT_SMALLPAGE, {STATE_CMD_READOOB | ACTION_OOBOFF, STATE_ADDR_PAGE | ACTION_CPY, + STATE_DATAOUT, STATE_READY}}, + /* Program page starting from the beginning */ + {OPT_ANY, {STATE_CMD_SEQIN, STATE_ADDR_PAGE, STATE_DATAIN, + STATE_CMD_PAGEPROG | ACTION_PRGPAGE, STATE_READY}}, + /* Program page starting from the beginning */ + {OPT_SMALLPAGE, {STATE_CMD_READ0, STATE_CMD_SEQIN | ACTION_ZEROOFF, STATE_ADDR_PAGE, + STATE_DATAIN, STATE_CMD_PAGEPROG | ACTION_PRGPAGE, STATE_READY}}, + /* Program page starting from the second half */ + {OPT_PAGE512, {STATE_CMD_READ1, STATE_CMD_SEQIN | ACTION_HALFOFF, STATE_ADDR_PAGE, + STATE_DATAIN, STATE_CMD_PAGEPROG | ACTION_PRGPAGE, STATE_READY}}, + /* Program OOB */ + {OPT_SMALLPAGE, {STATE_CMD_READOOB, STATE_CMD_SEQIN | ACTION_OOBOFF, STATE_ADDR_PAGE, + STATE_DATAIN, STATE_CMD_PAGEPROG | ACTION_PRGPAGE, STATE_READY}}, + /* Erase sector */ + {OPT_ANY, {STATE_CMD_ERASE1, STATE_ADDR_SEC, STATE_CMD_ERASE2 | ACTION_SECERASE, STATE_READY}}, + /* Read status */ + {OPT_ANY, {STATE_CMD_STATUS, STATE_DATAOUT_STATUS, STATE_READY}}, + /* Read ID */ + {OPT_ANY, {STATE_CMD_READID, STATE_ADDR_ZERO, STATE_DATAOUT_ID, STATE_READY}}, + /* Large page devices read page */ + {OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART | ACTION_CPY, + STATE_DATAOUT, STATE_READY}}, + /* Large page devices random page read */ + {OPT_LARGEPAGE, {STATE_CMD_RNDOUT, STATE_ADDR_COLUMN, STATE_CMD_RNDOUTSTART | ACTION_CPY, + STATE_DATAOUT, STATE_READY}}, +}; + +struct weak_block { + struct list_head list; + unsigned int erase_block_no; + unsigned int max_erases; + unsigned int erases_done; +}; + +static LIST_HEAD(weak_blocks); + +struct weak_page { + struct list_head list; + unsigned int page_no; + unsigned int max_writes; + unsigned int writes_done; +}; + +static LIST_HEAD(weak_pages); + +struct grave_page { + struct list_head list; + unsigned int page_no; + unsigned int max_reads; + unsigned int reads_done; +}; + +static LIST_HEAD(grave_pages); + +static unsigned long *erase_block_wear = NULL; +static unsigned int wear_eb_count = 0; +static unsigned long total_wear = 0; + +/* MTD structure for NAND controller */ +static struct mtd_info *nsmtd; + +static int nandsim_debugfs_show(struct seq_file *m, void *private) +{ + unsigned long wmin = -1, wmax = 0, avg; + unsigned long deciles[10], decile_max[10], tot = 0; + unsigned int i; + + /* Calc wear stats */ + for (i = 0; i < wear_eb_count; ++i) { + unsigned long wear = erase_block_wear[i]; + if (wear < wmin) + wmin = wear; + if (wear > wmax) + wmax = wear; + tot += wear; + } + + for (i = 0; i < 9; ++i) { + deciles[i] = 0; + decile_max[i] = (wmax * (i + 1) + 5) / 10; + } + deciles[9] = 0; + decile_max[9] = wmax; + for (i = 0; i < wear_eb_count; ++i) { + int d; + unsigned long wear = erase_block_wear[i]; + for (d = 0; d < 10; ++d) + if (wear <= decile_max[d]) { + deciles[d] += 1; + break; + } + } + avg = tot / wear_eb_count; + + /* Output wear report */ + seq_printf(m, "Total numbers of erases: %lu\n", tot); + seq_printf(m, "Number of erase blocks: %u\n", wear_eb_count); + seq_printf(m, "Average number of erases: %lu\n", avg); + seq_printf(m, "Maximum number of erases: %lu\n", wmax); + seq_printf(m, "Minimum number of erases: %lu\n", wmin); + for (i = 0; i < 10; ++i) { + unsigned long from = (i ? decile_max[i - 1] + 1 : 0); + if (from > decile_max[i]) + continue; + seq_printf(m, "Number of ebs with erase counts from %lu to %lu : %lu\n", + from, + decile_max[i], + deciles[i]); + } + + return 0; +} + +static int nandsim_debugfs_open(struct inode *inode, struct file *file) +{ + return single_open(file, nandsim_debugfs_show, inode->i_private); +} + +static const struct file_operations dfs_fops = { + .open = nandsim_debugfs_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + +/** + * nandsim_debugfs_create - initialize debugfs + * @dev: nandsim device description object + * + * This function creates all debugfs files for UBI device @ubi. Returns zero in + * case of success and a negative error code in case of failure. + */ +static int nandsim_debugfs_create(struct nandsim *dev) +{ + struct nandsim_debug_info *dbg = &dev->dbg; + struct dentry *dent; + int err; + + if (!IS_ENABLED(CONFIG_DEBUG_FS)) + return 0; + + dent = debugfs_create_dir("nandsim", NULL); + if (IS_ERR_OR_NULL(dent)) { + int err = dent ? -ENODEV : PTR_ERR(dent); + + NS_ERR("cannot create \"nandsim\" debugfs directory, err %d\n", + err); + return err; + } + dbg->dfs_root = dent; + + dent = debugfs_create_file("wear_report", S_IRUSR, + dbg->dfs_root, dev, &dfs_fops); + if (IS_ERR_OR_NULL(dent)) + goto out_remove; + dbg->dfs_wear_report = dent; + + return 0; + +out_remove: + debugfs_remove_recursive(dbg->dfs_root); + err = dent ? PTR_ERR(dent) : -ENODEV; + return err; +} + +/** + * nandsim_debugfs_remove - destroy all debugfs files + */ +static void nandsim_debugfs_remove(struct nandsim *ns) +{ + if (IS_ENABLED(CONFIG_DEBUG_FS)) + debugfs_remove_recursive(ns->dbg.dfs_root); +} + +/* + * Allocate array of page pointers, create slab allocation for an array + * and initialize the array by NULL pointers. + * + * RETURNS: 0 if success, -ENOMEM if memory alloc fails. + */ +static int alloc_device(struct nandsim *ns) +{ + struct file *cfile; + int i, err; + + if (cache_file) { + cfile = filp_open(cache_file, O_CREAT | O_RDWR | O_LARGEFILE, 0600); + if (IS_ERR(cfile)) + return PTR_ERR(cfile); + if (!(cfile->f_mode & FMODE_CAN_READ)) { + NS_ERR("alloc_device: cache file not readable\n"); + err = -EINVAL; + goto err_close; + } + if (!(cfile->f_mode & FMODE_CAN_WRITE)) { + NS_ERR("alloc_device: cache file not writeable\n"); + err = -EINVAL; + goto err_close; + } + ns->pages_written = vzalloc(BITS_TO_LONGS(ns->geom.pgnum) * + sizeof(unsigned long)); + if (!ns->pages_written) { + NS_ERR("alloc_device: unable to allocate pages written array\n"); + err = -ENOMEM; + goto err_close; + } + ns->file_buf = kmalloc(ns->geom.pgszoob, GFP_KERNEL); + if (!ns->file_buf) { + NS_ERR("alloc_device: unable to allocate file buf\n"); + err = -ENOMEM; + goto err_free; + } + ns->cfile = cfile; + return 0; + } + + ns->pages = vmalloc(ns->geom.pgnum * sizeof(union ns_mem)); + if (!ns->pages) { + NS_ERR("alloc_device: unable to allocate page array\n"); + return -ENOMEM; + } + for (i = 0; i < ns->geom.pgnum; i++) { + ns->pages[i].byte = NULL; + } + ns->nand_pages_slab = kmem_cache_create("nandsim", + ns->geom.pgszoob, 0, 0, NULL); + if (!ns->nand_pages_slab) { + NS_ERR("cache_create: unable to create kmem_cache\n"); + return -ENOMEM; + } + + return 0; + +err_free: + vfree(ns->pages_written); +err_close: + filp_close(cfile, NULL); + return err; +} + +/* + * Free any allocated pages, and free the array of page pointers. + */ +static void free_device(struct nandsim *ns) +{ + int i; + + if (ns->cfile) { + kfree(ns->file_buf); + vfree(ns->pages_written); + filp_close(ns->cfile, NULL); + return; + } + + if (ns->pages) { + for (i = 0; i < ns->geom.pgnum; i++) { + if (ns->pages[i].byte) + kmem_cache_free(ns->nand_pages_slab, + ns->pages[i].byte); + } + kmem_cache_destroy(ns->nand_pages_slab); + vfree(ns->pages); + } +} + +static char *get_partition_name(int i) +{ + return kasprintf(GFP_KERNEL, "NAND simulator partition %d", i); +} + +/* + * Initialize the nandsim structure. + * + * RETURNS: 0 if success, -ERRNO if failure. + */ +static int init_nandsim(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct nandsim *ns = chip->priv; + int i, ret = 0; + uint64_t remains; + uint64_t next_offset; + + if (NS_IS_INITIALIZED(ns)) { + NS_ERR("init_nandsim: nandsim is already initialized\n"); + return -EIO; + } + + /* Force mtd to not do delays */ + chip->chip_delay = 0; + + /* Initialize the NAND flash parameters */ + ns->busw = chip->options & NAND_BUSWIDTH_16 ? 16 : 8; + ns->geom.totsz = mtd->size; + ns->geom.pgsz = mtd->writesize; + ns->geom.oobsz = mtd->oobsize; + ns->geom.secsz = mtd->erasesize; + ns->geom.pgszoob = ns->geom.pgsz + ns->geom.oobsz; + ns->geom.pgnum = div_u64(ns->geom.totsz, ns->geom.pgsz); + ns->geom.totszoob = ns->geom.totsz + (uint64_t)ns->geom.pgnum * ns->geom.oobsz; + ns->geom.secshift = ffs(ns->geom.secsz) - 1; + ns->geom.pgshift = chip->page_shift; + ns->geom.pgsec = ns->geom.secsz / ns->geom.pgsz; + ns->geom.secszoob = ns->geom.secsz + ns->geom.oobsz * ns->geom.pgsec; + ns->options = 0; + + if (ns->geom.pgsz == 512) { + ns->options |= OPT_PAGE512; + if (ns->busw == 8) + ns->options |= OPT_PAGE512_8BIT; + } else if (ns->geom.pgsz == 2048) { + ns->options |= OPT_PAGE2048; + } else if (ns->geom.pgsz == 4096) { + ns->options |= OPT_PAGE4096; + } else { + NS_ERR("init_nandsim: unknown page size %u\n", ns->geom.pgsz); + return -EIO; + } + + if (ns->options & OPT_SMALLPAGE) { + if (ns->geom.totsz <= (32 << 20)) { + ns->geom.pgaddrbytes = 3; + ns->geom.secaddrbytes = 2; + } else { + ns->geom.pgaddrbytes = 4; + ns->geom.secaddrbytes = 3; + } + } else { + if (ns->geom.totsz <= (128 << 20)) { + ns->geom.pgaddrbytes = 4; + ns->geom.secaddrbytes = 2; + } else { + ns->geom.pgaddrbytes = 5; + ns->geom.secaddrbytes = 3; + } + } + + /* Fill the partition_info structure */ + if (parts_num > ARRAY_SIZE(ns->partitions)) { + NS_ERR("too many partitions.\n"); + ret = -EINVAL; + goto error; + } + remains = ns->geom.totsz; + next_offset = 0; + for (i = 0; i < parts_num; ++i) { + uint64_t part_sz = (uint64_t)parts[i] * ns->geom.secsz; + + if (!part_sz || part_sz > remains) { + NS_ERR("bad partition size.\n"); + ret = -EINVAL; + goto error; + } + ns->partitions[i].name = get_partition_name(i); + ns->partitions[i].offset = next_offset; + ns->partitions[i].size = part_sz; + next_offset += ns->partitions[i].size; + remains -= ns->partitions[i].size; + } + ns->nbparts = parts_num; + if (remains) { + if (parts_num + 1 > ARRAY_SIZE(ns->partitions)) { + NS_ERR("too many partitions.\n"); + ret = -EINVAL; + goto error; + } + ns->partitions[i].name = get_partition_name(i); + ns->partitions[i].offset = next_offset; + ns->partitions[i].size = remains; + ns->nbparts += 1; + } + + if (ns->busw == 16) + NS_WARN("16-bit flashes support wasn't tested\n"); + + printk("flash size: %llu MiB\n", + (unsigned long long)ns->geom.totsz >> 20); + printk("page size: %u bytes\n", ns->geom.pgsz); + printk("OOB area size: %u bytes\n", ns->geom.oobsz); + printk("sector size: %u KiB\n", ns->geom.secsz >> 10); + printk("pages number: %u\n", ns->geom.pgnum); + printk("pages per sector: %u\n", ns->geom.pgsec); + printk("bus width: %u\n", ns->busw); + printk("bits in sector size: %u\n", ns->geom.secshift); + printk("bits in page size: %u\n", ns->geom.pgshift); + printk("bits in OOB size: %u\n", ffs(ns->geom.oobsz) - 1); + printk("flash size with OOB: %llu KiB\n", + (unsigned long long)ns->geom.totszoob >> 10); + printk("page address bytes: %u\n", ns->geom.pgaddrbytes); + printk("sector address bytes: %u\n", ns->geom.secaddrbytes); + printk("options: %#x\n", ns->options); + + if ((ret = alloc_device(ns)) != 0) + goto error; + + /* Allocate / initialize the internal buffer */ + ns->buf.byte = kmalloc(ns->geom.pgszoob, GFP_KERNEL); + if (!ns->buf.byte) { + NS_ERR("init_nandsim: unable to allocate %u bytes for the internal buffer\n", + ns->geom.pgszoob); + ret = -ENOMEM; + goto error; + } + memset(ns->buf.byte, 0xFF, ns->geom.pgszoob); + + return 0; + +error: + free_device(ns); + + return ret; +} + +/* + * Free the nandsim structure. + */ +static void free_nandsim(struct nandsim *ns) +{ + kfree(ns->buf.byte); + free_device(ns); + + return; +} + +static int parse_badblocks(struct nandsim *ns, struct mtd_info *mtd) +{ + char *w; + int zero_ok; + unsigned int erase_block_no; + loff_t offset; + + if (!badblocks) + return 0; + w = badblocks; + do { + zero_ok = (*w == '0' ? 1 : 0); + erase_block_no = simple_strtoul(w, &w, 0); + if (!zero_ok && !erase_block_no) { + NS_ERR("invalid badblocks.\n"); + return -EINVAL; + } + offset = (loff_t)erase_block_no * ns->geom.secsz; + if (mtd_block_markbad(mtd, offset)) { + NS_ERR("invalid badblocks.\n"); + return -EINVAL; + } + if (*w == ',') + w += 1; + } while (*w); + return 0; +} + +static int parse_weakblocks(void) +{ + char *w; + int zero_ok; + unsigned int erase_block_no; + unsigned int max_erases; + struct weak_block *wb; + + if (!weakblocks) + return 0; + w = weakblocks; + do { + zero_ok = (*w == '0' ? 1 : 0); + erase_block_no = simple_strtoul(w, &w, 0); + if (!zero_ok && !erase_block_no) { + NS_ERR("invalid weakblocks.\n"); + return -EINVAL; + } + max_erases = 3; + if (*w == ':') { + w += 1; + max_erases = simple_strtoul(w, &w, 0); + } + if (*w == ',') + w += 1; + wb = kzalloc(sizeof(*wb), GFP_KERNEL); + if (!wb) { + NS_ERR("unable to allocate memory.\n"); + return -ENOMEM; + } + wb->erase_block_no = erase_block_no; + wb->max_erases = max_erases; + list_add(&wb->list, &weak_blocks); + } while (*w); + return 0; +} + +static int erase_error(unsigned int erase_block_no) +{ + struct weak_block *wb; + + list_for_each_entry(wb, &weak_blocks, list) + if (wb->erase_block_no == erase_block_no) { + if (wb->erases_done >= wb->max_erases) + return 1; + wb->erases_done += 1; + return 0; + } + return 0; +} + +static int parse_weakpages(void) +{ + char *w; + int zero_ok; + unsigned int page_no; + unsigned int max_writes; + struct weak_page *wp; + + if (!weakpages) + return 0; + w = weakpages; + do { + zero_ok = (*w == '0' ? 1 : 0); + page_no = simple_strtoul(w, &w, 0); + if (!zero_ok && !page_no) { + NS_ERR("invalid weakpagess.\n"); + return -EINVAL; + } + max_writes = 3; + if (*w == ':') { + w += 1; + max_writes = simple_strtoul(w, &w, 0); + } + if (*w == ',') + w += 1; + wp = kzalloc(sizeof(*wp), GFP_KERNEL); + if (!wp) { + NS_ERR("unable to allocate memory.\n"); + return -ENOMEM; + } + wp->page_no = page_no; + wp->max_writes = max_writes; + list_add(&wp->list, &weak_pages); + } while (*w); + return 0; +} + +static int write_error(unsigned int page_no) +{ + struct weak_page *wp; + + list_for_each_entry(wp, &weak_pages, list) + if (wp->page_no == page_no) { + if (wp->writes_done >= wp->max_writes) + return 1; + wp->writes_done += 1; + return 0; + } + return 0; +} + +static int parse_gravepages(void) +{ + char *g; + int zero_ok; + unsigned int page_no; + unsigned int max_reads; + struct grave_page *gp; + + if (!gravepages) + return 0; + g = gravepages; + do { + zero_ok = (*g == '0' ? 1 : 0); + page_no = simple_strtoul(g, &g, 0); + if (!zero_ok && !page_no) { + NS_ERR("invalid gravepagess.\n"); + return -EINVAL; + } + max_reads = 3; + if (*g == ':') { + g += 1; + max_reads = simple_strtoul(g, &g, 0); + } + if (*g == ',') + g += 1; + gp = kzalloc(sizeof(*gp), GFP_KERNEL); + if (!gp) { + NS_ERR("unable to allocate memory.\n"); + return -ENOMEM; + } + gp->page_no = page_no; + gp->max_reads = max_reads; + list_add(&gp->list, &grave_pages); + } while (*g); + return 0; +} + +static int read_error(unsigned int page_no) +{ + struct grave_page *gp; + + list_for_each_entry(gp, &grave_pages, list) + if (gp->page_no == page_no) { + if (gp->reads_done >= gp->max_reads) + return 1; + gp->reads_done += 1; + return 0; + } + return 0; +} + +static void free_lists(void) +{ + struct list_head *pos, *n; + list_for_each_safe(pos, n, &weak_blocks) { + list_del(pos); + kfree(list_entry(pos, struct weak_block, list)); + } + list_for_each_safe(pos, n, &weak_pages) { + list_del(pos); + kfree(list_entry(pos, struct weak_page, list)); + } + list_for_each_safe(pos, n, &grave_pages) { + list_del(pos); + kfree(list_entry(pos, struct grave_page, list)); + } + kfree(erase_block_wear); +} + +static int setup_wear_reporting(struct mtd_info *mtd) +{ + size_t mem; + + wear_eb_count = div_u64(mtd->size, mtd->erasesize); + mem = wear_eb_count * sizeof(unsigned long); + if (mem / sizeof(unsigned long) != wear_eb_count) { + NS_ERR("Too many erase blocks for wear reporting\n"); + return -ENOMEM; + } + erase_block_wear = kzalloc(mem, GFP_KERNEL); + if (!erase_block_wear) { + NS_ERR("Too many erase blocks for wear reporting\n"); + return -ENOMEM; + } + return 0; +} + +static void update_wear(unsigned int erase_block_no) +{ + if (!erase_block_wear) + return; + total_wear += 1; + /* + * TODO: Notify this through a debugfs entry, + * instead of showing an error message. + */ + if (total_wear == 0) + NS_ERR("Erase counter total overflow\n"); + erase_block_wear[erase_block_no] += 1; + if (erase_block_wear[erase_block_no] == 0) + NS_ERR("Erase counter overflow for erase block %u\n", erase_block_no); +} + +/* + * Returns the string representation of 'state' state. + */ +static char *get_state_name(uint32_t state) +{ + switch (NS_STATE(state)) { + case STATE_CMD_READ0: + return "STATE_CMD_READ0"; + case STATE_CMD_READ1: + return "STATE_CMD_READ1"; + case STATE_CMD_PAGEPROG: + return "STATE_CMD_PAGEPROG"; + case STATE_CMD_READOOB: + return "STATE_CMD_READOOB"; + case STATE_CMD_READSTART: + return "STATE_CMD_READSTART"; + case STATE_CMD_ERASE1: + return "STATE_CMD_ERASE1"; + case STATE_CMD_STATUS: + return "STATE_CMD_STATUS"; + case STATE_CMD_SEQIN: + return "STATE_CMD_SEQIN"; + case STATE_CMD_READID: + return "STATE_CMD_READID"; + case STATE_CMD_ERASE2: + return "STATE_CMD_ERASE2"; + case STATE_CMD_RESET: + return "STATE_CMD_RESET"; + case STATE_CMD_RNDOUT: + return "STATE_CMD_RNDOUT"; + case STATE_CMD_RNDOUTSTART: + return "STATE_CMD_RNDOUTSTART"; + case STATE_ADDR_PAGE: + return "STATE_ADDR_PAGE"; + case STATE_ADDR_SEC: + return "STATE_ADDR_SEC"; + case STATE_ADDR_ZERO: + return "STATE_ADDR_ZERO"; + case STATE_ADDR_COLUMN: + return "STATE_ADDR_COLUMN"; + case STATE_DATAIN: + return "STATE_DATAIN"; + case STATE_DATAOUT: + return "STATE_DATAOUT"; + case STATE_DATAOUT_ID: + return "STATE_DATAOUT_ID"; + case STATE_DATAOUT_STATUS: + return "STATE_DATAOUT_STATUS"; + case STATE_READY: + return "STATE_READY"; + case STATE_UNKNOWN: + return "STATE_UNKNOWN"; + } + + NS_ERR("get_state_name: unknown state, BUG\n"); + return NULL; +} + +/* + * Check if command is valid. + * + * RETURNS: 1 if wrong command, 0 if right. + */ +static int check_command(int cmd) +{ + switch (cmd) { + + case NAND_CMD_READ0: + case NAND_CMD_READ1: + case NAND_CMD_READSTART: + case NAND_CMD_PAGEPROG: + case NAND_CMD_READOOB: + case NAND_CMD_ERASE1: + case NAND_CMD_STATUS: + case NAND_CMD_SEQIN: + case NAND_CMD_READID: + case NAND_CMD_ERASE2: + case NAND_CMD_RESET: + case NAND_CMD_RNDOUT: + case NAND_CMD_RNDOUTSTART: + return 0; + + default: + return 1; + } +} + +/* + * Returns state after command is accepted by command number. + */ +static uint32_t get_state_by_command(unsigned command) +{ + switch (command) { + case NAND_CMD_READ0: + return STATE_CMD_READ0; + case NAND_CMD_READ1: + return STATE_CMD_READ1; + case NAND_CMD_PAGEPROG: + return STATE_CMD_PAGEPROG; + case NAND_CMD_READSTART: + return STATE_CMD_READSTART; + case NAND_CMD_READOOB: + return STATE_CMD_READOOB; + case NAND_CMD_ERASE1: + return STATE_CMD_ERASE1; + case NAND_CMD_STATUS: + return STATE_CMD_STATUS; + case NAND_CMD_SEQIN: + return STATE_CMD_SEQIN; + case NAND_CMD_READID: + return STATE_CMD_READID; + case NAND_CMD_ERASE2: + return STATE_CMD_ERASE2; + case NAND_CMD_RESET: + return STATE_CMD_RESET; + case NAND_CMD_RNDOUT: + return STATE_CMD_RNDOUT; + case NAND_CMD_RNDOUTSTART: + return STATE_CMD_RNDOUTSTART; + } + + NS_ERR("get_state_by_command: unknown command, BUG\n"); + return 0; +} + +/* + * Move an address byte to the correspondent internal register. + */ +static inline void accept_addr_byte(struct nandsim *ns, u_char bt) +{ + uint byte = (uint)bt; + + if (ns->regs.count < (ns->geom.pgaddrbytes - ns->geom.secaddrbytes)) + ns->regs.column |= (byte << 8 * ns->regs.count); + else { + ns->regs.row |= (byte << 8 * (ns->regs.count - + ns->geom.pgaddrbytes + + ns->geom.secaddrbytes)); + } + + return; +} + +/* + * Switch to STATE_READY state. + */ +static inline void switch_to_ready_state(struct nandsim *ns, u_char status) +{ + NS_DBG("switch_to_ready_state: switch to %s state\n", get_state_name(STATE_READY)); + + ns->state = STATE_READY; + ns->nxstate = STATE_UNKNOWN; + ns->op = NULL; + ns->npstates = 0; + ns->stateidx = 0; + ns->regs.num = 0; + ns->regs.count = 0; + ns->regs.off = 0; + ns->regs.row = 0; + ns->regs.column = 0; + ns->regs.status = status; +} + +/* + * If the operation isn't known yet, try to find it in the global array + * of supported operations. + * + * Operation can be unknown because of the following. + * 1. New command was accepted and this is the first call to find the + * correspondent states chain. In this case ns->npstates = 0; + * 2. There are several operations which begin with the same command(s) + * (for example program from the second half and read from the + * second half operations both begin with the READ1 command). In this + * case the ns->pstates[] array contains previous states. + * + * Thus, the function tries to find operation containing the following + * states (if the 'flag' parameter is 0): + * ns->pstates[0], ... ns->pstates[ns->npstates], ns->state + * + * If (one and only one) matching operation is found, it is accepted ( + * ns->ops, ns->state, ns->nxstate are initialized, ns->npstate is + * zeroed). + * + * If there are several matches, the current state is pushed to the + * ns->pstates. + * + * The operation can be unknown only while commands are input to the chip. + * As soon as address command is accepted, the operation must be known. + * In such situation the function is called with 'flag' != 0, and the + * operation is searched using the following pattern: + * ns->pstates[0], ... ns->pstates[ns->npstates], <address input> + * + * It is supposed that this pattern must either match one operation or + * none. There can't be ambiguity in that case. + * + * If no matches found, the function does the following: + * 1. if there are saved states present, try to ignore them and search + * again only using the last command. If nothing was found, switch + * to the STATE_READY state. + * 2. if there are no saved states, switch to the STATE_READY state. + * + * RETURNS: -2 - no matched operations found. + * -1 - several matches. + * 0 - operation is found. + */ +static int find_operation(struct nandsim *ns, uint32_t flag) +{ + int opsfound = 0; + int i, j, idx = 0; + + for (i = 0; i < NS_OPER_NUM; i++) { + + int found = 1; + + if (!(ns->options & ops[i].reqopts)) + /* Ignore operations we can't perform */ + continue; + + if (flag) { + if (!(ops[i].states[ns->npstates] & STATE_ADDR_MASK)) + continue; + } else { + if (NS_STATE(ns->state) != NS_STATE(ops[i].states[ns->npstates])) + continue; + } + + for (j = 0; j < ns->npstates; j++) + if (NS_STATE(ops[i].states[j]) != NS_STATE(ns->pstates[j]) + && (ns->options & ops[idx].reqopts)) { + found = 0; + break; + } + + if (found) { + idx = i; + opsfound += 1; + } + } + + if (opsfound == 1) { + /* Exact match */ + ns->op = &ops[idx].states[0]; + if (flag) { + /* + * In this case the find_operation function was + * called when address has just began input. But it isn't + * yet fully input and the current state must + * not be one of STATE_ADDR_*, but the STATE_ADDR_* + * state must be the next state (ns->nxstate). + */ + ns->stateidx = ns->npstates - 1; + } else { + ns->stateidx = ns->npstates; + } + ns->npstates = 0; + ns->state = ns->op[ns->stateidx]; + ns->nxstate = ns->op[ns->stateidx + 1]; + NS_DBG("find_operation: operation found, index: %d, state: %s, nxstate %s\n", + idx, get_state_name(ns->state), get_state_name(ns->nxstate)); + return 0; + } + + if (opsfound == 0) { + /* Nothing was found. Try to ignore previous commands (if any) and search again */ + if (ns->npstates != 0) { + NS_DBG("find_operation: no operation found, try again with state %s\n", + get_state_name(ns->state)); + ns->npstates = 0; + return find_operation(ns, 0); + + } + NS_DBG("find_operation: no operations found\n"); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return -2; + } + + if (flag) { + /* This shouldn't happen */ + NS_DBG("find_operation: BUG, operation must be known if address is input\n"); + return -2; + } + + NS_DBG("find_operation: there is still ambiguity\n"); + + ns->pstates[ns->npstates++] = ns->state; + + return -1; +} + +static void put_pages(struct nandsim *ns) +{ + int i; + + for (i = 0; i < ns->held_cnt; i++) + page_cache_release(ns->held_pages[i]); +} + +/* Get page cache pages in advance to provide NOFS memory allocation */ +static int get_pages(struct nandsim *ns, struct file *file, size_t count, loff_t pos) +{ + pgoff_t index, start_index, end_index; + struct page *page; + struct address_space *mapping = file->f_mapping; + + start_index = pos >> PAGE_CACHE_SHIFT; + end_index = (pos + count - 1) >> PAGE_CACHE_SHIFT; + if (end_index - start_index + 1 > NS_MAX_HELD_PAGES) + return -EINVAL; + ns->held_cnt = 0; + for (index = start_index; index <= end_index; index++) { + page = find_get_page(mapping, index); + if (page == NULL) { + page = find_or_create_page(mapping, index, GFP_NOFS); + if (page == NULL) { + write_inode_now(mapping->host, 1); + page = find_or_create_page(mapping, index, GFP_NOFS); + } + if (page == NULL) { + put_pages(ns); + return -ENOMEM; + } + unlock_page(page); + } + ns->held_pages[ns->held_cnt++] = page; + } + return 0; +} + +static int set_memalloc(void) +{ + if (current->flags & PF_MEMALLOC) + return 0; + current->flags |= PF_MEMALLOC; + return 1; +} + +static void clear_memalloc(int memalloc) +{ + if (memalloc) + current->flags &= ~PF_MEMALLOC; +} + +static ssize_t read_file(struct nandsim *ns, struct file *file, void *buf, size_t count, loff_t pos) +{ + ssize_t tx; + int err, memalloc; + + err = get_pages(ns, file, count, pos); + if (err) + return err; + memalloc = set_memalloc(); + tx = kernel_read(file, pos, buf, count); + clear_memalloc(memalloc); + put_pages(ns); + return tx; +} + +static ssize_t write_file(struct nandsim *ns, struct file *file, void *buf, size_t count, loff_t pos) +{ + ssize_t tx; + int err, memalloc; + + err = get_pages(ns, file, count, pos); + if (err) + return err; + memalloc = set_memalloc(); + tx = kernel_write(file, buf, count, pos); + clear_memalloc(memalloc); + put_pages(ns); + return tx; +} + +/* + * Returns a pointer to the current page. + */ +static inline union ns_mem *NS_GET_PAGE(struct nandsim *ns) +{ + return &(ns->pages[ns->regs.row]); +} + +/* + * Retuns a pointer to the current byte, within the current page. + */ +static inline u_char *NS_PAGE_BYTE_OFF(struct nandsim *ns) +{ + return NS_GET_PAGE(ns)->byte + ns->regs.column + ns->regs.off; +} + +static int do_read_error(struct nandsim *ns, int num) +{ + unsigned int page_no = ns->regs.row; + + if (read_error(page_no)) { + prandom_bytes(ns->buf.byte, num); + NS_WARN("simulating read error in page %u\n", page_no); + return 1; + } + return 0; +} + +static void do_bit_flips(struct nandsim *ns, int num) +{ + if (bitflips && prandom_u32() < (1 << 22)) { + int flips = 1; + if (bitflips > 1) + flips = (prandom_u32() % (int) bitflips) + 1; + while (flips--) { + int pos = prandom_u32() % (num * 8); + ns->buf.byte[pos / 8] ^= (1 << (pos % 8)); + NS_WARN("read_page: flipping bit %d in page %d " + "reading from %d ecc: corrected=%u failed=%u\n", + pos, ns->regs.row, ns->regs.column + ns->regs.off, + nsmtd->ecc_stats.corrected, nsmtd->ecc_stats.failed); + } + } +} + +/* + * Fill the NAND buffer with data read from the specified page. + */ +static void read_page(struct nandsim *ns, int num) +{ + union ns_mem *mypage; + + if (ns->cfile) { + if (!test_bit(ns->regs.row, ns->pages_written)) { + NS_DBG("read_page: page %d not written\n", ns->regs.row); + memset(ns->buf.byte, 0xFF, num); + } else { + loff_t pos; + ssize_t tx; + + NS_DBG("read_page: page %d written, reading from %d\n", + ns->regs.row, ns->regs.column + ns->regs.off); + if (do_read_error(ns, num)) + return; + pos = (loff_t)NS_RAW_OFFSET(ns) + ns->regs.off; + tx = read_file(ns, ns->cfile, ns->buf.byte, num, pos); + if (tx != num) { + NS_ERR("read_page: read error for page %d ret %ld\n", ns->regs.row, (long)tx); + return; + } + do_bit_flips(ns, num); + } + return; + } + + mypage = NS_GET_PAGE(ns); + if (mypage->byte == NULL) { + NS_DBG("read_page: page %d not allocated\n", ns->regs.row); + memset(ns->buf.byte, 0xFF, num); + } else { + NS_DBG("read_page: page %d allocated, reading from %d\n", + ns->regs.row, ns->regs.column + ns->regs.off); + if (do_read_error(ns, num)) + return; + memcpy(ns->buf.byte, NS_PAGE_BYTE_OFF(ns), num); + do_bit_flips(ns, num); + } +} + +/* + * Erase all pages in the specified sector. + */ +static void erase_sector(struct nandsim *ns) +{ + union ns_mem *mypage; + int i; + + if (ns->cfile) { + for (i = 0; i < ns->geom.pgsec; i++) + if (__test_and_clear_bit(ns->regs.row + i, + ns->pages_written)) { + NS_DBG("erase_sector: freeing page %d\n", ns->regs.row + i); + } + return; + } + + mypage = NS_GET_PAGE(ns); + for (i = 0; i < ns->geom.pgsec; i++) { + if (mypage->byte != NULL) { + NS_DBG("erase_sector: freeing page %d\n", ns->regs.row+i); + kmem_cache_free(ns->nand_pages_slab, mypage->byte); + mypage->byte = NULL; + } + mypage++; + } +} + +/* + * Program the specified page with the contents from the NAND buffer. + */ +static int prog_page(struct nandsim *ns, int num) +{ + int i; + union ns_mem *mypage; + u_char *pg_off; + + if (ns->cfile) { + loff_t off; + ssize_t tx; + int all; + + NS_DBG("prog_page: writing page %d\n", ns->regs.row); + pg_off = ns->file_buf + ns->regs.column + ns->regs.off; + off = (loff_t)NS_RAW_OFFSET(ns) + ns->regs.off; + if (!test_bit(ns->regs.row, ns->pages_written)) { + all = 1; + memset(ns->file_buf, 0xff, ns->geom.pgszoob); + } else { + all = 0; + tx = read_file(ns, ns->cfile, pg_off, num, off); + if (tx != num) { + NS_ERR("prog_page: read error for page %d ret %ld\n", ns->regs.row, (long)tx); + return -1; + } + } + for (i = 0; i < num; i++) + pg_off[i] &= ns->buf.byte[i]; + if (all) { + loff_t pos = (loff_t)ns->regs.row * ns->geom.pgszoob; + tx = write_file(ns, ns->cfile, ns->file_buf, ns->geom.pgszoob, pos); + if (tx != ns->geom.pgszoob) { + NS_ERR("prog_page: write error for page %d ret %ld\n", ns->regs.row, (long)tx); + return -1; + } + __set_bit(ns->regs.row, ns->pages_written); + } else { + tx = write_file(ns, ns->cfile, pg_off, num, off); + if (tx != num) { + NS_ERR("prog_page: write error for page %d ret %ld\n", ns->regs.row, (long)tx); + return -1; + } + } + return 0; + } + + mypage = NS_GET_PAGE(ns); + if (mypage->byte == NULL) { + NS_DBG("prog_page: allocating page %d\n", ns->regs.row); + /* + * We allocate memory with GFP_NOFS because a flash FS may + * utilize this. If it is holding an FS lock, then gets here, + * then kernel memory alloc runs writeback which goes to the FS + * again and deadlocks. This was seen in practice. + */ + mypage->byte = kmem_cache_alloc(ns->nand_pages_slab, GFP_NOFS); + if (mypage->byte == NULL) { + NS_ERR("prog_page: error allocating memory for page %d\n", ns->regs.row); + return -1; + } + memset(mypage->byte, 0xFF, ns->geom.pgszoob); + } + + pg_off = NS_PAGE_BYTE_OFF(ns); + for (i = 0; i < num; i++) + pg_off[i] &= ns->buf.byte[i]; + + return 0; +} + +/* + * If state has any action bit, perform this action. + * + * RETURNS: 0 if success, -1 if error. + */ +static int do_state_action(struct nandsim *ns, uint32_t action) +{ + int num; + int busdiv = ns->busw == 8 ? 1 : 2; + unsigned int erase_block_no, page_no; + + action &= ACTION_MASK; + + /* Check that page address input is correct */ + if (action != ACTION_SECERASE && ns->regs.row >= ns->geom.pgnum) { + NS_WARN("do_state_action: wrong page number (%#x)\n", ns->regs.row); + return -1; + } + + switch (action) { + + case ACTION_CPY: + /* + * Copy page data to the internal buffer. + */ + + /* Column shouldn't be very large */ + if (ns->regs.column >= (ns->geom.pgszoob - ns->regs.off)) { + NS_ERR("do_state_action: column number is too large\n"); + break; + } + num = ns->geom.pgszoob - ns->regs.off - ns->regs.column; + read_page(ns, num); + + NS_DBG("do_state_action: (ACTION_CPY:) copy %d bytes to int buf, raw offset %d\n", + num, NS_RAW_OFFSET(ns) + ns->regs.off); + + if (ns->regs.off == 0) + NS_LOG("read page %d\n", ns->regs.row); + else if (ns->regs.off < ns->geom.pgsz) + NS_LOG("read page %d (second half)\n", ns->regs.row); + else + NS_LOG("read OOB of page %d\n", ns->regs.row); + + NS_UDELAY(access_delay); + NS_UDELAY(input_cycle * ns->geom.pgsz / 1000 / busdiv); + + break; + + case ACTION_SECERASE: + /* + * Erase sector. + */ + + if (ns->lines.wp) { + NS_ERR("do_state_action: device is write-protected, ignore sector erase\n"); + return -1; + } + + if (ns->regs.row >= ns->geom.pgnum - ns->geom.pgsec + || (ns->regs.row & ~(ns->geom.secsz - 1))) { + NS_ERR("do_state_action: wrong sector address (%#x)\n", ns->regs.row); + return -1; + } + + ns->regs.row = (ns->regs.row << + 8 * (ns->geom.pgaddrbytes - ns->geom.secaddrbytes)) | ns->regs.column; + ns->regs.column = 0; + + erase_block_no = ns->regs.row >> (ns->geom.secshift - ns->geom.pgshift); + + NS_DBG("do_state_action: erase sector at address %#x, off = %d\n", + ns->regs.row, NS_RAW_OFFSET(ns)); + NS_LOG("erase sector %u\n", erase_block_no); + + erase_sector(ns); + + NS_MDELAY(erase_delay); + + if (erase_block_wear) + update_wear(erase_block_no); + + if (erase_error(erase_block_no)) { + NS_WARN("simulating erase failure in erase block %u\n", erase_block_no); + return -1; + } + + break; + + case ACTION_PRGPAGE: + /* + * Program page - move internal buffer data to the page. + */ + + if (ns->lines.wp) { + NS_WARN("do_state_action: device is write-protected, programm\n"); + return -1; + } + + num = ns->geom.pgszoob - ns->regs.off - ns->regs.column; + if (num != ns->regs.count) { + NS_ERR("do_state_action: too few bytes were input (%d instead of %d)\n", + ns->regs.count, num); + return -1; + } + + if (prog_page(ns, num) == -1) + return -1; + + page_no = ns->regs.row; + + NS_DBG("do_state_action: copy %d bytes from int buf to (%#x, %#x), raw off = %d\n", + num, ns->regs.row, ns->regs.column, NS_RAW_OFFSET(ns) + ns->regs.off); + NS_LOG("programm page %d\n", ns->regs.row); + + NS_UDELAY(programm_delay); + NS_UDELAY(output_cycle * ns->geom.pgsz / 1000 / busdiv); + + if (write_error(page_no)) { + NS_WARN("simulating write failure in page %u\n", page_no); + return -1; + } + + break; + + case ACTION_ZEROOFF: + NS_DBG("do_state_action: set internal offset to 0\n"); + ns->regs.off = 0; + break; + + case ACTION_HALFOFF: + if (!(ns->options & OPT_PAGE512_8BIT)) { + NS_ERR("do_state_action: BUG! can't skip half of page for non-512" + "byte page size 8x chips\n"); + return -1; + } + NS_DBG("do_state_action: set internal offset to %d\n", ns->geom.pgsz/2); + ns->regs.off = ns->geom.pgsz/2; + break; + + case ACTION_OOBOFF: + NS_DBG("do_state_action: set internal offset to %d\n", ns->geom.pgsz); + ns->regs.off = ns->geom.pgsz; + break; + + default: + NS_DBG("do_state_action: BUG! unknown action\n"); + } + + return 0; +} + +/* + * Switch simulator's state. + */ +static void switch_state(struct nandsim *ns) +{ + if (ns->op) { + /* + * The current operation have already been identified. + * Just follow the states chain. + */ + + ns->stateidx += 1; + ns->state = ns->nxstate; + ns->nxstate = ns->op[ns->stateidx + 1]; + + NS_DBG("switch_state: operation is known, switch to the next state, " + "state: %s, nxstate: %s\n", + get_state_name(ns->state), get_state_name(ns->nxstate)); + + /* See, whether we need to do some action */ + if ((ns->state & ACTION_MASK) && do_state_action(ns, ns->state) < 0) { + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + } else { + /* + * We don't yet know which operation we perform. + * Try to identify it. + */ + + /* + * The only event causing the switch_state function to + * be called with yet unknown operation is new command. + */ + ns->state = get_state_by_command(ns->regs.command); + + NS_DBG("switch_state: operation is unknown, try to find it\n"); + + if (find_operation(ns, 0) != 0) + return; + + if ((ns->state & ACTION_MASK) && do_state_action(ns, ns->state) < 0) { + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + } + + /* For 16x devices column means the page offset in words */ + if ((ns->nxstate & STATE_ADDR_MASK) && ns->busw == 16) { + NS_DBG("switch_state: double the column number for 16x device\n"); + ns->regs.column <<= 1; + } + + if (NS_STATE(ns->nxstate) == STATE_READY) { + /* + * The current state is the last. Return to STATE_READY + */ + + u_char status = NS_STATUS_OK(ns); + + /* In case of data states, see if all bytes were input/output */ + if ((ns->state & (STATE_DATAIN_MASK | STATE_DATAOUT_MASK)) + && ns->regs.count != ns->regs.num) { + NS_WARN("switch_state: not all bytes were processed, %d left\n", + ns->regs.num - ns->regs.count); + status = NS_STATUS_FAILED(ns); + } + + NS_DBG("switch_state: operation complete, switch to STATE_READY state\n"); + + switch_to_ready_state(ns, status); + + return; + } else if (ns->nxstate & (STATE_DATAIN_MASK | STATE_DATAOUT_MASK)) { + /* + * If the next state is data input/output, switch to it now + */ + + ns->state = ns->nxstate; + ns->nxstate = ns->op[++ns->stateidx + 1]; + ns->regs.num = ns->regs.count = 0; + + NS_DBG("switch_state: the next state is data I/O, switch, " + "state: %s, nxstate: %s\n", + get_state_name(ns->state), get_state_name(ns->nxstate)); + + /* + * Set the internal register to the count of bytes which + * are expected to be input or output + */ + switch (NS_STATE(ns->state)) { + case STATE_DATAIN: + case STATE_DATAOUT: + ns->regs.num = ns->geom.pgszoob - ns->regs.off - ns->regs.column; + break; + + case STATE_DATAOUT_ID: + ns->regs.num = ns->geom.idbytes; + break; + + case STATE_DATAOUT_STATUS: + ns->regs.count = ns->regs.num = 0; + break; + + default: + NS_ERR("switch_state: BUG! unknown data state\n"); + } + + } else if (ns->nxstate & STATE_ADDR_MASK) { + /* + * If the next state is address input, set the internal + * register to the number of expected address bytes + */ + + ns->regs.count = 0; + + switch (NS_STATE(ns->nxstate)) { + case STATE_ADDR_PAGE: + ns->regs.num = ns->geom.pgaddrbytes; + + break; + case STATE_ADDR_SEC: + ns->regs.num = ns->geom.secaddrbytes; + break; + + case STATE_ADDR_ZERO: + ns->regs.num = 1; + break; + + case STATE_ADDR_COLUMN: + /* Column address is always 2 bytes */ + ns->regs.num = ns->geom.pgaddrbytes - ns->geom.secaddrbytes; + break; + + default: + NS_ERR("switch_state: BUG! unknown address state\n"); + } + } else { + /* + * Just reset internal counters. + */ + + ns->regs.num = 0; + ns->regs.count = 0; + } +} + +static u_char ns_nand_read_byte(struct mtd_info *mtd) +{ + struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv; + u_char outb = 0x00; + + /* Sanity and correctness checks */ + if (!ns->lines.ce) { + NS_ERR("read_byte: chip is disabled, return %#x\n", (uint)outb); + return outb; + } + if (ns->lines.ale || ns->lines.cle) { + NS_ERR("read_byte: ALE or CLE pin is high, return %#x\n", (uint)outb); + return outb; + } + if (!(ns->state & STATE_DATAOUT_MASK)) { + NS_WARN("read_byte: unexpected data output cycle, state is %s " + "return %#x\n", get_state_name(ns->state), (uint)outb); + return outb; + } + + /* Status register may be read as many times as it is wanted */ + if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS) { + NS_DBG("read_byte: return %#x status\n", ns->regs.status); + return ns->regs.status; + } + + /* Check if there is any data in the internal buffer which may be read */ + if (ns->regs.count == ns->regs.num) { + NS_WARN("read_byte: no more data to output, return %#x\n", (uint)outb); + return outb; + } + + switch (NS_STATE(ns->state)) { + case STATE_DATAOUT: + if (ns->busw == 8) { + outb = ns->buf.byte[ns->regs.count]; + ns->regs.count += 1; + } else { + outb = (u_char)cpu_to_le16(ns->buf.word[ns->regs.count >> 1]); + ns->regs.count += 2; + } + break; + case STATE_DATAOUT_ID: + NS_DBG("read_byte: read ID byte %d, total = %d\n", ns->regs.count, ns->regs.num); + outb = ns->ids[ns->regs.count]; + ns->regs.count += 1; + break; + default: + BUG(); + } + + if (ns->regs.count == ns->regs.num) { + NS_DBG("read_byte: all bytes were read\n"); + + if (NS_STATE(ns->nxstate) == STATE_READY) + switch_state(ns); + } + + return outb; +} + +static void ns_nand_write_byte(struct mtd_info *mtd, u_char byte) +{ + struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv; + + /* Sanity and correctness checks */ + if (!ns->lines.ce) { + NS_ERR("write_byte: chip is disabled, ignore write\n"); + return; + } + if (ns->lines.ale && ns->lines.cle) { + NS_ERR("write_byte: ALE and CLE pins are high simultaneously, ignore write\n"); + return; + } + + if (ns->lines.cle == 1) { + /* + * The byte written is a command. + */ + + if (byte == NAND_CMD_RESET) { + NS_LOG("reset chip\n"); + switch_to_ready_state(ns, NS_STATUS_OK(ns)); + return; + } + + /* Check that the command byte is correct */ + if (check_command(byte)) { + NS_ERR("write_byte: unknown command %#x\n", (uint)byte); + return; + } + + if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS + || NS_STATE(ns->state) == STATE_DATAOUT) { + int row = ns->regs.row; + + switch_state(ns); + if (byte == NAND_CMD_RNDOUT) + ns->regs.row = row; + } + + /* Check if chip is expecting command */ + if (NS_STATE(ns->nxstate) != STATE_UNKNOWN && !(ns->nxstate & STATE_CMD_MASK)) { + /* Do not warn if only 2 id bytes are read */ + if (!(ns->regs.command == NAND_CMD_READID && + NS_STATE(ns->state) == STATE_DATAOUT_ID && ns->regs.count == 2)) { + /* + * We are in situation when something else (not command) + * was expected but command was input. In this case ignore + * previous command(s)/state(s) and accept the last one. + */ + NS_WARN("write_byte: command (%#x) wasn't expected, expected state is %s, " + "ignore previous states\n", (uint)byte, get_state_name(ns->nxstate)); + } + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + } + + NS_DBG("command byte corresponding to %s state accepted\n", + get_state_name(get_state_by_command(byte))); + ns->regs.command = byte; + switch_state(ns); + + } else if (ns->lines.ale == 1) { + /* + * The byte written is an address. + */ + + if (NS_STATE(ns->nxstate) == STATE_UNKNOWN) { + + NS_DBG("write_byte: operation isn't known yet, identify it\n"); + + if (find_operation(ns, 1) < 0) + return; + + if ((ns->state & ACTION_MASK) && do_state_action(ns, ns->state) < 0) { + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + ns->regs.count = 0; + switch (NS_STATE(ns->nxstate)) { + case STATE_ADDR_PAGE: + ns->regs.num = ns->geom.pgaddrbytes; + break; + case STATE_ADDR_SEC: + ns->regs.num = ns->geom.secaddrbytes; + break; + case STATE_ADDR_ZERO: + ns->regs.num = 1; + break; + default: + BUG(); + } + } + + /* Check that chip is expecting address */ + if (!(ns->nxstate & STATE_ADDR_MASK)) { + NS_ERR("write_byte: address (%#x) isn't expected, expected state is %s, " + "switch to STATE_READY\n", (uint)byte, get_state_name(ns->nxstate)); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + /* Check if this is expected byte */ + if (ns->regs.count == ns->regs.num) { + NS_ERR("write_byte: no more address bytes expected\n"); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + accept_addr_byte(ns, byte); + + ns->regs.count += 1; + + NS_DBG("write_byte: address byte %#x was accepted (%d bytes input, %d expected)\n", + (uint)byte, ns->regs.count, ns->regs.num); + + if (ns->regs.count == ns->regs.num) { + NS_DBG("address (%#x, %#x) is accepted\n", ns->regs.row, ns->regs.column); + switch_state(ns); + } + + } else { + /* + * The byte written is an input data. + */ + + /* Check that chip is expecting data input */ + if (!(ns->state & STATE_DATAIN_MASK)) { + NS_ERR("write_byte: data input (%#x) isn't expected, state is %s, " + "switch to %s\n", (uint)byte, + get_state_name(ns->state), get_state_name(STATE_READY)); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + /* Check if this is expected byte */ + if (ns->regs.count == ns->regs.num) { + NS_WARN("write_byte: %u input bytes has already been accepted, ignore write\n", + ns->regs.num); + return; + } + + if (ns->busw == 8) { + ns->buf.byte[ns->regs.count] = byte; + ns->regs.count += 1; + } else { + ns->buf.word[ns->regs.count >> 1] = cpu_to_le16((uint16_t)byte); + ns->regs.count += 2; + } + } + + return; +} + +static void ns_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int bitmask) +{ + struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv; + + ns->lines.cle = bitmask & NAND_CLE ? 1 : 0; + ns->lines.ale = bitmask & NAND_ALE ? 1 : 0; + ns->lines.ce = bitmask & NAND_NCE ? 1 : 0; + + if (cmd != NAND_CMD_NONE) + ns_nand_write_byte(mtd, cmd); +} + +static int ns_device_ready(struct mtd_info *mtd) +{ + NS_DBG("device_ready\n"); + return 1; +} + +static uint16_t ns_nand_read_word(struct mtd_info *mtd) +{ + struct nand_chip *chip = (struct nand_chip *)mtd->priv; + + NS_DBG("read_word\n"); + + return chip->read_byte(mtd) | (chip->read_byte(mtd) << 8); +} + +static void ns_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv; + + /* Check that chip is expecting data input */ + if (!(ns->state & STATE_DATAIN_MASK)) { + NS_ERR("write_buf: data input isn't expected, state is %s, " + "switch to STATE_READY\n", get_state_name(ns->state)); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + /* Check if these are expected bytes */ + if (ns->regs.count + len > ns->regs.num) { + NS_ERR("write_buf: too many input bytes\n"); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + memcpy(ns->buf.byte + ns->regs.count, buf, len); + ns->regs.count += len; + + if (ns->regs.count == ns->regs.num) { + NS_DBG("write_buf: %d bytes were written\n", ns->regs.count); + } +} + +static void ns_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nandsim *ns = ((struct nand_chip *)mtd->priv)->priv; + + /* Sanity and correctness checks */ + if (!ns->lines.ce) { + NS_ERR("read_buf: chip is disabled\n"); + return; + } + if (ns->lines.ale || ns->lines.cle) { + NS_ERR("read_buf: ALE or CLE pin is high\n"); + return; + } + if (!(ns->state & STATE_DATAOUT_MASK)) { + NS_WARN("read_buf: unexpected data output cycle, current state is %s\n", + get_state_name(ns->state)); + return; + } + + if (NS_STATE(ns->state) != STATE_DATAOUT) { + int i; + + for (i = 0; i < len; i++) + buf[i] = ((struct nand_chip *)mtd->priv)->read_byte(mtd); + + return; + } + + /* Check if these are expected bytes */ + if (ns->regs.count + len > ns->regs.num) { + NS_ERR("read_buf: too many bytes to read\n"); + switch_to_ready_state(ns, NS_STATUS_FAILED(ns)); + return; + } + + memcpy(buf, ns->buf.byte + ns->regs.count, len); + ns->regs.count += len; + + if (ns->regs.count == ns->regs.num) { + if (NS_STATE(ns->nxstate) == STATE_READY) + switch_state(ns); + } + + return; +} + +/* + * Module initialization function + */ +static int __init ns_init_module(void) +{ + struct nand_chip *chip; + struct nandsim *nand; + int retval = -ENOMEM, i; + + if (bus_width != 8 && bus_width != 16) { + NS_ERR("wrong bus width (%d), use only 8 or 16\n", bus_width); + return -EINVAL; + } + + /* Allocate and initialize mtd_info, nand_chip and nandsim structures */ + nsmtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip) + + sizeof(struct nandsim), GFP_KERNEL); + if (!nsmtd) { + NS_ERR("unable to allocate core structures.\n"); + return -ENOMEM; + } + chip = (struct nand_chip *)(nsmtd + 1); + nsmtd->priv = (void *)chip; + nand = (struct nandsim *)(chip + 1); + chip->priv = (void *)nand; + + /* + * Register simulator's callbacks. + */ + chip->cmd_ctrl = ns_hwcontrol; + chip->read_byte = ns_nand_read_byte; + chip->dev_ready = ns_device_ready; + chip->write_buf = ns_nand_write_buf; + chip->read_buf = ns_nand_read_buf; + chip->read_word = ns_nand_read_word; + chip->ecc.mode = NAND_ECC_SOFT; + /* The NAND_SKIP_BBTSCAN option is necessary for 'overridesize' */ + /* and 'badblocks' parameters to work */ + chip->options |= NAND_SKIP_BBTSCAN; + + switch (bbt) { + case 2: + chip->bbt_options |= NAND_BBT_NO_OOB; + case 1: + chip->bbt_options |= NAND_BBT_USE_FLASH; + case 0: + break; + default: + NS_ERR("bbt has to be 0..2\n"); + retval = -EINVAL; + goto error; + } + /* + * Perform minimum nandsim structure initialization to handle + * the initial ID read command correctly + */ + if (id_bytes[6] != 0xFF || id_bytes[7] != 0xFF) + nand->geom.idbytes = 8; + else if (id_bytes[4] != 0xFF || id_bytes[5] != 0xFF) + nand->geom.idbytes = 6; + else if (id_bytes[2] != 0xFF || id_bytes[3] != 0xFF) + nand->geom.idbytes = 4; + else + nand->geom.idbytes = 2; + nand->regs.status = NS_STATUS_OK(nand); + nand->nxstate = STATE_UNKNOWN; + nand->options |= OPT_PAGE512; /* temporary value */ + memcpy(nand->ids, id_bytes, sizeof(nand->ids)); + if (bus_width == 16) { + nand->busw = 16; + chip->options |= NAND_BUSWIDTH_16; + } + + nsmtd->owner = THIS_MODULE; + + if ((retval = parse_weakblocks()) != 0) + goto error; + + if ((retval = parse_weakpages()) != 0) + goto error; + + if ((retval = parse_gravepages()) != 0) + goto error; + + retval = nand_scan_ident(nsmtd, 1, NULL); + if (retval) { + NS_ERR("cannot scan NAND Simulator device\n"); + if (retval > 0) + retval = -ENXIO; + goto error; + } + + if (bch) { + unsigned int eccsteps, eccbytes; + if (!mtd_nand_has_bch()) { + NS_ERR("BCH ECC support is disabled\n"); + retval = -EINVAL; + goto error; + } + /* use 512-byte ecc blocks */ + eccsteps = nsmtd->writesize/512; + eccbytes = (bch*13+7)/8; + /* do not bother supporting small page devices */ + if ((nsmtd->oobsize < 64) || !eccsteps) { + NS_ERR("bch not available on small page devices\n"); + retval = -EINVAL; + goto error; + } + if ((eccbytes*eccsteps+2) > nsmtd->oobsize) { + NS_ERR("invalid bch value %u\n", bch); + retval = -EINVAL; + goto error; + } + chip->ecc.mode = NAND_ECC_SOFT_BCH; + chip->ecc.size = 512; + chip->ecc.strength = bch; + chip->ecc.bytes = eccbytes; + NS_INFO("using %u-bit/%u bytes BCH ECC\n", bch, chip->ecc.size); + } + + retval = nand_scan_tail(nsmtd); + if (retval) { + NS_ERR("can't register NAND Simulator\n"); + if (retval > 0) + retval = -ENXIO; + goto error; + } + + if (overridesize) { + uint64_t new_size = (uint64_t)nsmtd->erasesize << overridesize; + if (new_size >> overridesize != nsmtd->erasesize) { + NS_ERR("overridesize is too big\n"); + retval = -EINVAL; + goto err_exit; + } + /* N.B. This relies on nand_scan not doing anything with the size before we change it */ + nsmtd->size = new_size; + chip->chipsize = new_size; + chip->chip_shift = ffs(nsmtd->erasesize) + overridesize - 1; + chip->pagemask = (chip->chipsize >> chip->page_shift) - 1; + } + + if ((retval = setup_wear_reporting(nsmtd)) != 0) + goto err_exit; + + if ((retval = nandsim_debugfs_create(nand)) != 0) + goto err_exit; + + if ((retval = init_nandsim(nsmtd)) != 0) + goto err_exit; + + if ((retval = chip->scan_bbt(nsmtd)) != 0) + goto err_exit; + + if ((retval = parse_badblocks(nand, nsmtd)) != 0) + goto err_exit; + + /* Register NAND partitions */ + retval = mtd_device_register(nsmtd, &nand->partitions[0], + nand->nbparts); + if (retval != 0) + goto err_exit; + + return 0; + +err_exit: + free_nandsim(nand); + nand_release(nsmtd); + for (i = 0;i < ARRAY_SIZE(nand->partitions); ++i) + kfree(nand->partitions[i].name); +error: + kfree(nsmtd); + free_lists(); + + return retval; +} + +module_init(ns_init_module); + +/* + * Module clean-up function + */ +static void __exit ns_cleanup_module(void) +{ + struct nandsim *ns = ((struct nand_chip *)nsmtd->priv)->priv; + int i; + + nandsim_debugfs_remove(ns); + free_nandsim(ns); /* Free nandsim private resources */ + nand_release(nsmtd); /* Unregister driver */ + for (i = 0;i < ARRAY_SIZE(ns->partitions); ++i) + kfree(ns->partitions[i].name); + kfree(nsmtd); /* Free other structures */ + free_lists(); +} + +module_exit(ns_cleanup_module); + +MODULE_LICENSE ("GPL"); +MODULE_AUTHOR ("Artem B. Bityuckiy"); +MODULE_DESCRIPTION ("The NAND flash simulator"); diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/ndfc.c new file mode 100644 index 000000000..3187c6b92 --- /dev/null +++ b/drivers/mtd/nand/ndfc.c @@ -0,0 +1,290 @@ +/* + * drivers/mtd/ndfc.c + * + * Overview: + * Platform independent driver for NDFC (NanD Flash Controller) + * integrated into EP440 cores + * + * Ported to an OF platform driver by Sean MacLennan + * + * The NDFC supports multiple chips, but this driver only supports a + * single chip since I do not have access to any boards with + * multiple chips. + * + * Author: Thomas Gleixner + * + * Copyright 2006 IBM + * Copyright 2008 PIKA Technologies + * Sean MacLennan <smaclennan@pikatech.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include <linux/module.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/ndfc.h> +#include <linux/slab.h> +#include <linux/mtd/mtd.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <asm/io.h> + +#define NDFC_MAX_CS 4 + +struct ndfc_controller { + struct platform_device *ofdev; + void __iomem *ndfcbase; + struct mtd_info mtd; + struct nand_chip chip; + int chip_select; + struct nand_hw_control ndfc_control; +}; + +static struct ndfc_controller ndfc_ctrl[NDFC_MAX_CS]; + +static void ndfc_select_chip(struct mtd_info *mtd, int chip) +{ + uint32_t ccr; + struct nand_chip *nchip = mtd->priv; + struct ndfc_controller *ndfc = nchip->priv; + + ccr = in_be32(ndfc->ndfcbase + NDFC_CCR); + if (chip >= 0) { + ccr &= ~NDFC_CCR_BS_MASK; + ccr |= NDFC_CCR_BS(chip + ndfc->chip_select); + } else + ccr |= NDFC_CCR_RESET_CE; + out_be32(ndfc->ndfcbase + NDFC_CCR, ccr); +} + +static void ndfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writel(cmd & 0xFF, ndfc->ndfcbase + NDFC_CMD); + else + writel(cmd & 0xFF, ndfc->ndfcbase + NDFC_ALE); +} + +static int ndfc_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + + return in_be32(ndfc->ndfcbase + NDFC_STAT) & NDFC_STAT_IS_READY; +} + +static void ndfc_enable_hwecc(struct mtd_info *mtd, int mode) +{ + uint32_t ccr; + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + + ccr = in_be32(ndfc->ndfcbase + NDFC_CCR); + ccr |= NDFC_CCR_RESET_ECC; + out_be32(ndfc->ndfcbase + NDFC_CCR, ccr); + wmb(); +} + +static int ndfc_calculate_ecc(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_code) +{ + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + uint32_t ecc; + uint8_t *p = (uint8_t *)&ecc; + + wmb(); + ecc = in_be32(ndfc->ndfcbase + NDFC_ECC); + /* The NDFC uses Smart Media (SMC) bytes order */ + ecc_code[0] = p[1]; + ecc_code[1] = p[2]; + ecc_code[2] = p[3]; + + return 0; +} + +/* + * Speedups for buffer read/write/verify + * + * NDFC allows 32bit read/write of data. So we can speed up the buffer + * functions. No further checking, as nand_base will always read/write + * page aligned. + */ +static void ndfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + uint32_t *p = (uint32_t *) buf; + + for(;len > 0; len -= 4) + *p++ = in_be32(ndfc->ndfcbase + NDFC_DATA); +} + +static void ndfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + struct ndfc_controller *ndfc = chip->priv; + uint32_t *p = (uint32_t *) buf; + + for(;len > 0; len -= 4) + out_be32(ndfc->ndfcbase + NDFC_DATA, *p++); +} + +/* + * Initialize chip structure + */ +static int ndfc_chip_init(struct ndfc_controller *ndfc, + struct device_node *node) +{ + struct device_node *flash_np; + struct nand_chip *chip = &ndfc->chip; + struct mtd_part_parser_data ppdata; + int ret; + + chip->IO_ADDR_R = ndfc->ndfcbase + NDFC_DATA; + chip->IO_ADDR_W = ndfc->ndfcbase + NDFC_DATA; + chip->cmd_ctrl = ndfc_hwcontrol; + chip->dev_ready = ndfc_ready; + chip->select_chip = ndfc_select_chip; + chip->chip_delay = 50; + chip->controller = &ndfc->ndfc_control; + chip->read_buf = ndfc_read_buf; + chip->write_buf = ndfc_write_buf; + chip->ecc.correct = nand_correct_data; + chip->ecc.hwctl = ndfc_enable_hwecc; + chip->ecc.calculate = ndfc_calculate_ecc; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 256; + chip->ecc.bytes = 3; + chip->ecc.strength = 1; + chip->priv = ndfc; + + ndfc->mtd.priv = chip; + ndfc->mtd.owner = THIS_MODULE; + + flash_np = of_get_next_child(node, NULL); + if (!flash_np) + return -ENODEV; + + ppdata.of_node = flash_np; + ndfc->mtd.name = kasprintf(GFP_KERNEL, "%s.%s", + dev_name(&ndfc->ofdev->dev), flash_np->name); + if (!ndfc->mtd.name) { + ret = -ENOMEM; + goto err; + } + + ret = nand_scan(&ndfc->mtd, 1); + if (ret) + goto err; + + ret = mtd_device_parse_register(&ndfc->mtd, NULL, &ppdata, NULL, 0); + +err: + of_node_put(flash_np); + if (ret) + kfree(ndfc->mtd.name); + return ret; +} + +static int ndfc_probe(struct platform_device *ofdev) +{ + struct ndfc_controller *ndfc; + const __be32 *reg; + u32 ccr; + u32 cs; + int err, len; + + /* Read the reg property to get the chip select */ + reg = of_get_property(ofdev->dev.of_node, "reg", &len); + if (reg == NULL || len != 12) { + dev_err(&ofdev->dev, "unable read reg property (%d)\n", len); + return -ENOENT; + } + + cs = be32_to_cpu(reg[0]); + if (cs >= NDFC_MAX_CS) { + dev_err(&ofdev->dev, "invalid CS number (%d)\n", cs); + return -EINVAL; + } + + ndfc = &ndfc_ctrl[cs]; + ndfc->chip_select = cs; + + spin_lock_init(&ndfc->ndfc_control.lock); + init_waitqueue_head(&ndfc->ndfc_control.wq); + ndfc->ofdev = ofdev; + dev_set_drvdata(&ofdev->dev, ndfc); + + ndfc->ndfcbase = of_iomap(ofdev->dev.of_node, 0); + if (!ndfc->ndfcbase) { + dev_err(&ofdev->dev, "failed to get memory\n"); + return -EIO; + } + + ccr = NDFC_CCR_BS(ndfc->chip_select); + + /* It is ok if ccr does not exist - just default to 0 */ + reg = of_get_property(ofdev->dev.of_node, "ccr", NULL); + if (reg) + ccr |= be32_to_cpup(reg); + + out_be32(ndfc->ndfcbase + NDFC_CCR, ccr); + + /* Set the bank settings if given */ + reg = of_get_property(ofdev->dev.of_node, "bank-settings", NULL); + if (reg) { + int offset = NDFC_BCFG0 + (ndfc->chip_select << 2); + out_be32(ndfc->ndfcbase + offset, be32_to_cpup(reg)); + } + + err = ndfc_chip_init(ndfc, ofdev->dev.of_node); + if (err) { + iounmap(ndfc->ndfcbase); + return err; + } + + return 0; +} + +static int ndfc_remove(struct platform_device *ofdev) +{ + struct ndfc_controller *ndfc = dev_get_drvdata(&ofdev->dev); + + nand_release(&ndfc->mtd); + kfree(ndfc->mtd.name); + + return 0; +} + +static const struct of_device_id ndfc_match[] = { + { .compatible = "ibm,ndfc", }, + {} +}; +MODULE_DEVICE_TABLE(of, ndfc_match); + +static struct platform_driver ndfc_driver = { + .driver = { + .name = "ndfc", + .of_match_table = ndfc_match, + }, + .probe = ndfc_probe, + .remove = ndfc_remove, +}; + +module_platform_driver(ndfc_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>"); +MODULE_DESCRIPTION("OF Platform driver for NDFC"); diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/nuc900_nand.c new file mode 100644 index 000000000..e58c644dd --- /dev/null +++ b/drivers/mtd/nand/nuc900_nand.c @@ -0,0 +1,311 @@ +/* + * Copyright © 2009 Nuvoton technology corporation. + * + * Wan ZongShun <mcuos.com@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation;version 2 of the License. + * + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> + +#define REG_FMICSR 0x00 +#define REG_SMCSR 0xa0 +#define REG_SMISR 0xac +#define REG_SMCMD 0xb0 +#define REG_SMADDR 0xb4 +#define REG_SMDATA 0xb8 + +#define RESET_FMI 0x01 +#define NAND_EN 0x08 +#define READYBUSY (0x01 << 18) + +#define SWRST 0x01 +#define PSIZE (0x01 << 3) +#define DMARWEN (0x03 << 1) +#define BUSWID (0x01 << 4) +#define ECC4EN (0x01 << 5) +#define WP (0x01 << 24) +#define NANDCS (0x01 << 25) +#define ENDADDR (0x01 << 31) + +#define read_data_reg(dev) \ + __raw_readl((dev)->reg + REG_SMDATA) + +#define write_data_reg(dev, val) \ + __raw_writel((val), (dev)->reg + REG_SMDATA) + +#define write_cmd_reg(dev, val) \ + __raw_writel((val), (dev)->reg + REG_SMCMD) + +#define write_addr_reg(dev, val) \ + __raw_writel((val), (dev)->reg + REG_SMADDR) + +struct nuc900_nand { + struct mtd_info mtd; + struct nand_chip chip; + void __iomem *reg; + struct clk *clk; + spinlock_t lock; +}; + +static const struct mtd_partition partitions[] = { + { + .name = "NAND FS 0", + .offset = 0, + .size = 8 * 1024 * 1024 + }, + { + .name = "NAND FS 1", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL + } +}; + +static unsigned char nuc900_nand_read_byte(struct mtd_info *mtd) +{ + unsigned char ret; + struct nuc900_nand *nand; + + nand = container_of(mtd, struct nuc900_nand, mtd); + + ret = (unsigned char)read_data_reg(nand); + + return ret; +} + +static void nuc900_nand_read_buf(struct mtd_info *mtd, + unsigned char *buf, int len) +{ + int i; + struct nuc900_nand *nand; + + nand = container_of(mtd, struct nuc900_nand, mtd); + + for (i = 0; i < len; i++) + buf[i] = (unsigned char)read_data_reg(nand); +} + +static void nuc900_nand_write_buf(struct mtd_info *mtd, + const unsigned char *buf, int len) +{ + int i; + struct nuc900_nand *nand; + + nand = container_of(mtd, struct nuc900_nand, mtd); + + for (i = 0; i < len; i++) + write_data_reg(nand, buf[i]); +} + +static int nuc900_check_rb(struct nuc900_nand *nand) +{ + unsigned int val; + spin_lock(&nand->lock); + val = __raw_readl(REG_SMISR); + val &= READYBUSY; + spin_unlock(&nand->lock); + + return val; +} + +static int nuc900_nand_devready(struct mtd_info *mtd) +{ + struct nuc900_nand *nand; + int ready; + + nand = container_of(mtd, struct nuc900_nand, mtd); + + ready = (nuc900_check_rb(nand)) ? 1 : 0; + return ready; +} + +static void nuc900_nand_command_lp(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + register struct nand_chip *chip = mtd->priv; + struct nuc900_nand *nand; + + nand = container_of(mtd, struct nuc900_nand, mtd); + + if (command == NAND_CMD_READOOB) { + column += mtd->writesize; + command = NAND_CMD_READ0; + } + + write_cmd_reg(nand, command & 0xff); + + if (column != -1 || page_addr != -1) { + + if (column != -1) { + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; + write_addr_reg(nand, column); + write_addr_reg(nand, column >> 8 | ENDADDR); + } + if (page_addr != -1) { + write_addr_reg(nand, page_addr); + + if (chip->chipsize > (128 << 20)) { + write_addr_reg(nand, page_addr >> 8); + write_addr_reg(nand, page_addr >> 16 | ENDADDR); + } else { + write_addr_reg(nand, page_addr >> 8 | ENDADDR); + } + } + } + + switch (command) { + case NAND_CMD_CACHEDPROG: + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_RNDIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + if (chip->dev_ready) + break; + udelay(chip->chip_delay); + + write_cmd_reg(nand, NAND_CMD_STATUS); + write_cmd_reg(nand, command); + + while (!nuc900_check_rb(nand)) + ; + + return; + + case NAND_CMD_RNDOUT: + write_cmd_reg(nand, NAND_CMD_RNDOUTSTART); + return; + + case NAND_CMD_READ0: + + write_cmd_reg(nand, NAND_CMD_READSTART); + default: + + if (!chip->dev_ready) { + udelay(chip->chip_delay); + return; + } + } + + /* Apply this short delay always to ensure that we do wait tWB in + * any case on any machine. */ + ndelay(100); + + while (!chip->dev_ready(mtd)) + ; +} + + +static void nuc900_nand_enable(struct nuc900_nand *nand) +{ + unsigned int val; + spin_lock(&nand->lock); + __raw_writel(RESET_FMI, (nand->reg + REG_FMICSR)); + + val = __raw_readl(nand->reg + REG_FMICSR); + + if (!(val & NAND_EN)) + __raw_writel(val | NAND_EN, nand->reg + REG_FMICSR); + + val = __raw_readl(nand->reg + REG_SMCSR); + + val &= ~(SWRST|PSIZE|DMARWEN|BUSWID|ECC4EN|NANDCS); + val |= WP; + + __raw_writel(val, nand->reg + REG_SMCSR); + + spin_unlock(&nand->lock); +} + +static int nuc900_nand_probe(struct platform_device *pdev) +{ + struct nuc900_nand *nuc900_nand; + struct nand_chip *chip; + struct resource *res; + + nuc900_nand = devm_kzalloc(&pdev->dev, sizeof(struct nuc900_nand), + GFP_KERNEL); + if (!nuc900_nand) + return -ENOMEM; + chip = &(nuc900_nand->chip); + + nuc900_nand->mtd.priv = chip; + nuc900_nand->mtd.owner = THIS_MODULE; + spin_lock_init(&nuc900_nand->lock); + + nuc900_nand->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(nuc900_nand->clk)) + return -ENOENT; + clk_enable(nuc900_nand->clk); + + chip->cmdfunc = nuc900_nand_command_lp; + chip->dev_ready = nuc900_nand_devready; + chip->read_byte = nuc900_nand_read_byte; + chip->write_buf = nuc900_nand_write_buf; + chip->read_buf = nuc900_nand_read_buf; + chip->chip_delay = 50; + chip->options = 0; + chip->ecc.mode = NAND_ECC_SOFT; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nuc900_nand->reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(nuc900_nand->reg)) + return PTR_ERR(nuc900_nand->reg); + + nuc900_nand_enable(nuc900_nand); + + if (nand_scan(&(nuc900_nand->mtd), 1)) + return -ENXIO; + + mtd_device_register(&(nuc900_nand->mtd), partitions, + ARRAY_SIZE(partitions)); + + platform_set_drvdata(pdev, nuc900_nand); + + return 0; +} + +static int nuc900_nand_remove(struct platform_device *pdev) +{ + struct nuc900_nand *nuc900_nand = platform_get_drvdata(pdev); + + nand_release(&nuc900_nand->mtd); + clk_disable(nuc900_nand->clk); + + return 0; +} + +static struct platform_driver nuc900_nand_driver = { + .probe = nuc900_nand_probe, + .remove = nuc900_nand_remove, + .driver = { + .name = "nuc900-fmi", + }, +}; + +module_platform_driver(nuc900_nand_driver); + +MODULE_AUTHOR("Wan ZongShun <mcuos.com@gmail.com>"); +MODULE_DESCRIPTION("w90p910/NUC9xx nand driver!"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:nuc900-fmi"); diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c new file mode 100644 index 000000000..60fa89939 --- /dev/null +++ b/drivers/mtd/nand/omap2.c @@ -0,0 +1,2086 @@ +/* + * Copyright © 2004 Texas Instruments, Jian Zhang <jzhang@ti.com> + * Copyright © 2004 Micron Technology Inc. + * Copyright © 2004 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/platform_device.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/jiffies.h> +#include <linux/sched.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/omap-dma.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/of_device.h> + +#include <linux/mtd/nand_bch.h> +#include <linux/platform_data/elm.h> + +#include <linux/platform_data/mtd-nand-omap2.h> + +#define DRIVER_NAME "omap2-nand" +#define OMAP_NAND_TIMEOUT_MS 5000 + +#define NAND_Ecc_P1e (1 << 0) +#define NAND_Ecc_P2e (1 << 1) +#define NAND_Ecc_P4e (1 << 2) +#define NAND_Ecc_P8e (1 << 3) +#define NAND_Ecc_P16e (1 << 4) +#define NAND_Ecc_P32e (1 << 5) +#define NAND_Ecc_P64e (1 << 6) +#define NAND_Ecc_P128e (1 << 7) +#define NAND_Ecc_P256e (1 << 8) +#define NAND_Ecc_P512e (1 << 9) +#define NAND_Ecc_P1024e (1 << 10) +#define NAND_Ecc_P2048e (1 << 11) + +#define NAND_Ecc_P1o (1 << 16) +#define NAND_Ecc_P2o (1 << 17) +#define NAND_Ecc_P4o (1 << 18) +#define NAND_Ecc_P8o (1 << 19) +#define NAND_Ecc_P16o (1 << 20) +#define NAND_Ecc_P32o (1 << 21) +#define NAND_Ecc_P64o (1 << 22) +#define NAND_Ecc_P128o (1 << 23) +#define NAND_Ecc_P256o (1 << 24) +#define NAND_Ecc_P512o (1 << 25) +#define NAND_Ecc_P1024o (1 << 26) +#define NAND_Ecc_P2048o (1 << 27) + +#define TF(value) (value ? 1 : 0) + +#define P2048e(a) (TF(a & NAND_Ecc_P2048e) << 0) +#define P2048o(a) (TF(a & NAND_Ecc_P2048o) << 1) +#define P1e(a) (TF(a & NAND_Ecc_P1e) << 2) +#define P1o(a) (TF(a & NAND_Ecc_P1o) << 3) +#define P2e(a) (TF(a & NAND_Ecc_P2e) << 4) +#define P2o(a) (TF(a & NAND_Ecc_P2o) << 5) +#define P4e(a) (TF(a & NAND_Ecc_P4e) << 6) +#define P4o(a) (TF(a & NAND_Ecc_P4o) << 7) + +#define P8e(a) (TF(a & NAND_Ecc_P8e) << 0) +#define P8o(a) (TF(a & NAND_Ecc_P8o) << 1) +#define P16e(a) (TF(a & NAND_Ecc_P16e) << 2) +#define P16o(a) (TF(a & NAND_Ecc_P16o) << 3) +#define P32e(a) (TF(a & NAND_Ecc_P32e) << 4) +#define P32o(a) (TF(a & NAND_Ecc_P32o) << 5) +#define P64e(a) (TF(a & NAND_Ecc_P64e) << 6) +#define P64o(a) (TF(a & NAND_Ecc_P64o) << 7) + +#define P128e(a) (TF(a & NAND_Ecc_P128e) << 0) +#define P128o(a) (TF(a & NAND_Ecc_P128o) << 1) +#define P256e(a) (TF(a & NAND_Ecc_P256e) << 2) +#define P256o(a) (TF(a & NAND_Ecc_P256o) << 3) +#define P512e(a) (TF(a & NAND_Ecc_P512e) << 4) +#define P512o(a) (TF(a & NAND_Ecc_P512o) << 5) +#define P1024e(a) (TF(a & NAND_Ecc_P1024e) << 6) +#define P1024o(a) (TF(a & NAND_Ecc_P1024o) << 7) + +#define P8e_s(a) (TF(a & NAND_Ecc_P8e) << 0) +#define P8o_s(a) (TF(a & NAND_Ecc_P8o) << 1) +#define P16e_s(a) (TF(a & NAND_Ecc_P16e) << 2) +#define P16o_s(a) (TF(a & NAND_Ecc_P16o) << 3) +#define P1e_s(a) (TF(a & NAND_Ecc_P1e) << 4) +#define P1o_s(a) (TF(a & NAND_Ecc_P1o) << 5) +#define P2e_s(a) (TF(a & NAND_Ecc_P2e) << 6) +#define P2o_s(a) (TF(a & NAND_Ecc_P2o) << 7) + +#define P4e_s(a) (TF(a & NAND_Ecc_P4e) << 0) +#define P4o_s(a) (TF(a & NAND_Ecc_P4o) << 1) + +#define PREFETCH_CONFIG1_CS_SHIFT 24 +#define ECC_CONFIG_CS_SHIFT 1 +#define CS_MASK 0x7 +#define ENABLE_PREFETCH (0x1 << 7) +#define DMA_MPU_MODE_SHIFT 2 +#define ECCSIZE0_SHIFT 12 +#define ECCSIZE1_SHIFT 22 +#define ECC1RESULTSIZE 0x1 +#define ECCCLEAR 0x100 +#define ECC1 0x1 +#define PREFETCH_FIFOTHRESHOLD_MAX 0x40 +#define PREFETCH_FIFOTHRESHOLD(val) ((val) << 8) +#define PREFETCH_STATUS_COUNT(val) (val & 0x00003fff) +#define PREFETCH_STATUS_FIFO_CNT(val) ((val >> 24) & 0x7F) +#define STATUS_BUFF_EMPTY 0x00000001 + +#define OMAP24XX_DMA_GPMC 4 + +#define SECTOR_BYTES 512 +/* 4 bit padding to make byte aligned, 56 = 52 + 4 */ +#define BCH4_BIT_PAD 4 + +/* GPMC ecc engine settings for read */ +#define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */ +#define BCH8R_ECC_SIZE0 0x1a /* ecc_size0 = 26 */ +#define BCH8R_ECC_SIZE1 0x2 /* ecc_size1 = 2 */ +#define BCH4R_ECC_SIZE0 0xd /* ecc_size0 = 13 */ +#define BCH4R_ECC_SIZE1 0x3 /* ecc_size1 = 3 */ + +/* GPMC ecc engine settings for write */ +#define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */ +#define BCH_ECC_SIZE0 0x0 /* ecc_size0 = 0, no oob protection */ +#define BCH_ECC_SIZE1 0x20 /* ecc_size1 = 32 */ + +#define BADBLOCK_MARKER_LENGTH 2 + +static u_char bch16_vector[] = {0xf5, 0x24, 0x1c, 0xd0, 0x61, 0xb3, 0xf1, 0x55, + 0x2e, 0x2c, 0x86, 0xa3, 0xed, 0x36, 0x1b, 0x78, + 0x48, 0x76, 0xa9, 0x3b, 0x97, 0xd1, 0x7a, 0x93, + 0x07, 0x0e}; +static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc, + 0xac, 0x6b, 0xff, 0x99, 0x7b}; +static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10}; + +/* Shared among all NAND instances to synchronize access to the ECC Engine */ +static struct nand_hw_control omap_gpmc_controller = { + .lock = __SPIN_LOCK_UNLOCKED(omap_gpmc_controller.lock), + .wq = __WAIT_QUEUE_HEAD_INITIALIZER(omap_gpmc_controller.wq), +}; + +struct omap_nand_info { + struct omap_nand_platform_data *pdata; + struct mtd_info mtd; + struct nand_chip nand; + struct platform_device *pdev; + + int gpmc_cs; + unsigned long phys_base; + enum omap_ecc ecc_opt; + struct completion comp; + struct dma_chan *dma; + int gpmc_irq_fifo; + int gpmc_irq_count; + enum { + OMAP_NAND_IO_READ = 0, /* read */ + OMAP_NAND_IO_WRITE, /* write */ + } iomode; + u_char *buf; + int buf_len; + struct gpmc_nand_regs reg; + /* generated at runtime depending on ECC algorithm and layout selected */ + struct nand_ecclayout oobinfo; + /* fields specific for BCHx_HW ECC scheme */ + struct device *elm_dev; + struct device_node *of_node; +}; + +/** + * omap_prefetch_enable - configures and starts prefetch transfer + * @cs: cs (chip select) number + * @fifo_th: fifo threshold to be used for read/ write + * @dma_mode: dma mode enable (1) or disable (0) + * @u32_count: number of bytes to be transferred + * @is_write: prefetch read(0) or write post(1) mode + */ +static int omap_prefetch_enable(int cs, int fifo_th, int dma_mode, + unsigned int u32_count, int is_write, struct omap_nand_info *info) +{ + u32 val; + + if (fifo_th > PREFETCH_FIFOTHRESHOLD_MAX) + return -1; + + if (readl(info->reg.gpmc_prefetch_control)) + return -EBUSY; + + /* Set the amount of bytes to be prefetched */ + writel(u32_count, info->reg.gpmc_prefetch_config2); + + /* Set dma/mpu mode, the prefetch read / post write and + * enable the engine. Set which cs is has requested for. + */ + val = ((cs << PREFETCH_CONFIG1_CS_SHIFT) | + PREFETCH_FIFOTHRESHOLD(fifo_th) | ENABLE_PREFETCH | + (dma_mode << DMA_MPU_MODE_SHIFT) | (0x1 & is_write)); + writel(val, info->reg.gpmc_prefetch_config1); + + /* Start the prefetch engine */ + writel(0x1, info->reg.gpmc_prefetch_control); + + return 0; +} + +/** + * omap_prefetch_reset - disables and stops the prefetch engine + */ +static int omap_prefetch_reset(int cs, struct omap_nand_info *info) +{ + u32 config1; + + /* check if the same module/cs is trying to reset */ + config1 = readl(info->reg.gpmc_prefetch_config1); + if (((config1 >> PREFETCH_CONFIG1_CS_SHIFT) & CS_MASK) != cs) + return -EINVAL; + + /* Stop the PFPW engine */ + writel(0x0, info->reg.gpmc_prefetch_control); + + /* Reset/disable the PFPW engine */ + writel(0x0, info->reg.gpmc_prefetch_config1); + + return 0; +} + +/** + * omap_hwcontrol - hardware specific access to control-lines + * @mtd: MTD device structure + * @cmd: command to device + * @ctrl: + * NAND_NCE: bit 0 -> don't care + * NAND_CLE: bit 1 -> Command Latch + * NAND_ALE: bit 2 -> Address Latch + * + * NOTE: boards may use different bits for these!! + */ +static void omap_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + + if (cmd != NAND_CMD_NONE) { + if (ctrl & NAND_CLE) + writeb(cmd, info->reg.gpmc_nand_command); + + else if (ctrl & NAND_ALE) + writeb(cmd, info->reg.gpmc_nand_address); + + else /* NAND_NCE */ + writeb(cmd, info->reg.gpmc_nand_data); + } +} + +/** + * omap_read_buf8 - read data from NAND controller into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void omap_read_buf8(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *nand = mtd->priv; + + ioread8_rep(nand->IO_ADDR_R, buf, len); +} + +/** + * omap_write_buf8 - write buffer to NAND controller + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void omap_write_buf8(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + u_char *p = (u_char *)buf; + u32 status = 0; + + while (len--) { + iowrite8(*p++, info->nand.IO_ADDR_W); + /* wait until buffer is available for write */ + do { + status = readl(info->reg.gpmc_status) & + STATUS_BUFF_EMPTY; + } while (!status); + } +} + +/** + * omap_read_buf16 - read data from NAND controller into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void omap_read_buf16(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *nand = mtd->priv; + + ioread16_rep(nand->IO_ADDR_R, buf, len / 2); +} + +/** + * omap_write_buf16 - write buffer to NAND controller + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void omap_write_buf16(struct mtd_info *mtd, const u_char * buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + u16 *p = (u16 *) buf; + u32 status = 0; + /* FIXME try bursts of writesw() or DMA ... */ + len >>= 1; + + while (len--) { + iowrite16(*p++, info->nand.IO_ADDR_W); + /* wait until buffer is available for write */ + do { + status = readl(info->reg.gpmc_status) & + STATUS_BUFF_EMPTY; + } while (!status); + } +} + +/** + * omap_read_buf_pref - read data from NAND controller into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + uint32_t r_count = 0; + int ret = 0; + u32 *p = (u32 *)buf; + + /* take care of subpage reads */ + if (len % 4) { + if (info->nand.options & NAND_BUSWIDTH_16) + omap_read_buf16(mtd, buf, len % 4); + else + omap_read_buf8(mtd, buf, len % 4); + p = (u32 *) (buf + len % 4); + len -= len % 4; + } + + /* configure and start prefetch transfer */ + ret = omap_prefetch_enable(info->gpmc_cs, + PREFETCH_FIFOTHRESHOLD_MAX, 0x0, len, 0x0, info); + if (ret) { + /* PFPW engine is busy, use cpu copy method */ + if (info->nand.options & NAND_BUSWIDTH_16) + omap_read_buf16(mtd, (u_char *)p, len); + else + omap_read_buf8(mtd, (u_char *)p, len); + } else { + do { + r_count = readl(info->reg.gpmc_prefetch_status); + r_count = PREFETCH_STATUS_FIFO_CNT(r_count); + r_count = r_count >> 2; + ioread32_rep(info->nand.IO_ADDR_R, p, r_count); + p += r_count; + len -= r_count << 2; + } while (len); + /* disable and stop the PFPW engine */ + omap_prefetch_reset(info->gpmc_cs, info); + } +} + +/** + * omap_write_buf_pref - write buffer to NAND controller + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void omap_write_buf_pref(struct mtd_info *mtd, + const u_char *buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + uint32_t w_count = 0; + int i = 0, ret = 0; + u16 *p = (u16 *)buf; + unsigned long tim, limit; + u32 val; + + /* take care of subpage writes */ + if (len % 2 != 0) { + writeb(*buf, info->nand.IO_ADDR_W); + p = (u16 *)(buf + 1); + len--; + } + + /* configure and start prefetch transfer */ + ret = omap_prefetch_enable(info->gpmc_cs, + PREFETCH_FIFOTHRESHOLD_MAX, 0x0, len, 0x1, info); + if (ret) { + /* PFPW engine is busy, use cpu copy method */ + if (info->nand.options & NAND_BUSWIDTH_16) + omap_write_buf16(mtd, (u_char *)p, len); + else + omap_write_buf8(mtd, (u_char *)p, len); + } else { + while (len) { + w_count = readl(info->reg.gpmc_prefetch_status); + w_count = PREFETCH_STATUS_FIFO_CNT(w_count); + w_count = w_count >> 1; + for (i = 0; (i < w_count) && len; i++, len -= 2) + iowrite16(*p++, info->nand.IO_ADDR_W); + } + /* wait for data to flushed-out before reset the prefetch */ + tim = 0; + limit = (loops_per_jiffy * + msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS)); + do { + cpu_relax(); + val = readl(info->reg.gpmc_prefetch_status); + val = PREFETCH_STATUS_COUNT(val); + } while (val && (tim++ < limit)); + + /* disable and stop the PFPW engine */ + omap_prefetch_reset(info->gpmc_cs, info); + } +} + +/* + * omap_nand_dma_callback: callback on the completion of dma transfer + * @data: pointer to completion data structure + */ +static void omap_nand_dma_callback(void *data) +{ + complete((struct completion *) data); +} + +/* + * omap_nand_dma_transfer: configure and start dma transfer + * @mtd: MTD device structure + * @addr: virtual address in RAM of source/destination + * @len: number of data bytes to be transferred + * @is_write: flag for read/write operation + */ +static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr, + unsigned int len, int is_write) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + struct dma_async_tx_descriptor *tx; + enum dma_data_direction dir = is_write ? DMA_TO_DEVICE : + DMA_FROM_DEVICE; + struct scatterlist sg; + unsigned long tim, limit; + unsigned n; + int ret; + u32 val; + + if (addr >= high_memory) { + struct page *p1; + + if (((size_t)addr & PAGE_MASK) != + ((size_t)(addr + len - 1) & PAGE_MASK)) + goto out_copy; + p1 = vmalloc_to_page(addr); + if (!p1) + goto out_copy; + addr = page_address(p1) + ((size_t)addr & ~PAGE_MASK); + } + + sg_init_one(&sg, addr, len); + n = dma_map_sg(info->dma->device->dev, &sg, 1, dir); + if (n == 0) { + dev_err(&info->pdev->dev, + "Couldn't DMA map a %d byte buffer\n", len); + goto out_copy; + } + + tx = dmaengine_prep_slave_sg(info->dma, &sg, n, + is_write ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!tx) + goto out_copy_unmap; + + tx->callback = omap_nand_dma_callback; + tx->callback_param = &info->comp; + dmaengine_submit(tx); + + /* configure and start prefetch transfer */ + ret = omap_prefetch_enable(info->gpmc_cs, + PREFETCH_FIFOTHRESHOLD_MAX, 0x1, len, is_write, info); + if (ret) + /* PFPW engine is busy, use cpu copy method */ + goto out_copy_unmap; + + init_completion(&info->comp); + dma_async_issue_pending(info->dma); + + /* setup and start DMA using dma_addr */ + wait_for_completion(&info->comp); + tim = 0; + limit = (loops_per_jiffy * msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS)); + + do { + cpu_relax(); + val = readl(info->reg.gpmc_prefetch_status); + val = PREFETCH_STATUS_COUNT(val); + } while (val && (tim++ < limit)); + + /* disable and stop the PFPW engine */ + omap_prefetch_reset(info->gpmc_cs, info); + + dma_unmap_sg(info->dma->device->dev, &sg, 1, dir); + return 0; + +out_copy_unmap: + dma_unmap_sg(info->dma->device->dev, &sg, 1, dir); +out_copy: + if (info->nand.options & NAND_BUSWIDTH_16) + is_write == 0 ? omap_read_buf16(mtd, (u_char *) addr, len) + : omap_write_buf16(mtd, (u_char *) addr, len); + else + is_write == 0 ? omap_read_buf8(mtd, (u_char *) addr, len) + : omap_write_buf8(mtd, (u_char *) addr, len); + return 0; +} + +/** + * omap_read_buf_dma_pref - read data from NAND controller into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void omap_read_buf_dma_pref(struct mtd_info *mtd, u_char *buf, int len) +{ + if (len <= mtd->oobsize) + omap_read_buf_pref(mtd, buf, len); + else + /* start transfer in DMA mode */ + omap_nand_dma_transfer(mtd, buf, len, 0x0); +} + +/** + * omap_write_buf_dma_pref - write buffer to NAND controller + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void omap_write_buf_dma_pref(struct mtd_info *mtd, + const u_char *buf, int len) +{ + if (len <= mtd->oobsize) + omap_write_buf_pref(mtd, buf, len); + else + /* start transfer in DMA mode */ + omap_nand_dma_transfer(mtd, (u_char *) buf, len, 0x1); +} + +/* + * omap_nand_irq - GPMC irq handler + * @this_irq: gpmc irq number + * @dev: omap_nand_info structure pointer is passed here + */ +static irqreturn_t omap_nand_irq(int this_irq, void *dev) +{ + struct omap_nand_info *info = (struct omap_nand_info *) dev; + u32 bytes; + + bytes = readl(info->reg.gpmc_prefetch_status); + bytes = PREFETCH_STATUS_FIFO_CNT(bytes); + bytes = bytes & 0xFFFC; /* io in multiple of 4 bytes */ + if (info->iomode == OMAP_NAND_IO_WRITE) { /* checks for write io */ + if (this_irq == info->gpmc_irq_count) + goto done; + + if (info->buf_len && (info->buf_len < bytes)) + bytes = info->buf_len; + else if (!info->buf_len) + bytes = 0; + iowrite32_rep(info->nand.IO_ADDR_W, + (u32 *)info->buf, bytes >> 2); + info->buf = info->buf + bytes; + info->buf_len -= bytes; + + } else { + ioread32_rep(info->nand.IO_ADDR_R, + (u32 *)info->buf, bytes >> 2); + info->buf = info->buf + bytes; + + if (this_irq == info->gpmc_irq_count) + goto done; + } + + return IRQ_HANDLED; + +done: + complete(&info->comp); + + disable_irq_nosync(info->gpmc_irq_fifo); + disable_irq_nosync(info->gpmc_irq_count); + + return IRQ_HANDLED; +} + +/* + * omap_read_buf_irq_pref - read data from NAND controller into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void omap_read_buf_irq_pref(struct mtd_info *mtd, u_char *buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + int ret = 0; + + if (len <= mtd->oobsize) { + omap_read_buf_pref(mtd, buf, len); + return; + } + + info->iomode = OMAP_NAND_IO_READ; + info->buf = buf; + init_completion(&info->comp); + + /* configure and start prefetch transfer */ + ret = omap_prefetch_enable(info->gpmc_cs, + PREFETCH_FIFOTHRESHOLD_MAX/2, 0x0, len, 0x0, info); + if (ret) + /* PFPW engine is busy, use cpu copy method */ + goto out_copy; + + info->buf_len = len; + + enable_irq(info->gpmc_irq_count); + enable_irq(info->gpmc_irq_fifo); + + /* waiting for read to complete */ + wait_for_completion(&info->comp); + + /* disable and stop the PFPW engine */ + omap_prefetch_reset(info->gpmc_cs, info); + return; + +out_copy: + if (info->nand.options & NAND_BUSWIDTH_16) + omap_read_buf16(mtd, buf, len); + else + omap_read_buf8(mtd, buf, len); +} + +/* + * omap_write_buf_irq_pref - write buffer to NAND controller + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void omap_write_buf_irq_pref(struct mtd_info *mtd, + const u_char *buf, int len) +{ + struct omap_nand_info *info = container_of(mtd, + struct omap_nand_info, mtd); + int ret = 0; + unsigned long tim, limit; + u32 val; + + if (len <= mtd->oobsize) { + omap_write_buf_pref(mtd, buf, len); + return; + } + + info->iomode = OMAP_NAND_IO_WRITE; + info->buf = (u_char *) buf; + init_completion(&info->comp); + + /* configure and start prefetch transfer : size=24 */ + ret = omap_prefetch_enable(info->gpmc_cs, + (PREFETCH_FIFOTHRESHOLD_MAX * 3) / 8, 0x0, len, 0x1, info); + if (ret) + /* PFPW engine is busy, use cpu copy method */ + goto out_copy; + + info->buf_len = len; + + enable_irq(info->gpmc_irq_count); + enable_irq(info->gpmc_irq_fifo); + + /* waiting for write to complete */ + wait_for_completion(&info->comp); + + /* wait for data to flushed-out before reset the prefetch */ + tim = 0; + limit = (loops_per_jiffy * msecs_to_jiffies(OMAP_NAND_TIMEOUT_MS)); + do { + val = readl(info->reg.gpmc_prefetch_status); + val = PREFETCH_STATUS_COUNT(val); + cpu_relax(); + } while (val && (tim++ < limit)); + + /* disable and stop the PFPW engine */ + omap_prefetch_reset(info->gpmc_cs, info); + return; + +out_copy: + if (info->nand.options & NAND_BUSWIDTH_16) + omap_write_buf16(mtd, buf, len); + else + omap_write_buf8(mtd, buf, len); +} + +/** + * gen_true_ecc - This function will generate true ECC value + * @ecc_buf: buffer to store ecc code + * + * This generated true ECC value can be used when correcting + * data read from NAND flash memory core + */ +static void gen_true_ecc(u8 *ecc_buf) +{ + u32 tmp = ecc_buf[0] | (ecc_buf[1] << 16) | + ((ecc_buf[2] & 0xF0) << 20) | ((ecc_buf[2] & 0x0F) << 8); + + ecc_buf[0] = ~(P64o(tmp) | P64e(tmp) | P32o(tmp) | P32e(tmp) | + P16o(tmp) | P16e(tmp) | P8o(tmp) | P8e(tmp)); + ecc_buf[1] = ~(P1024o(tmp) | P1024e(tmp) | P512o(tmp) | P512e(tmp) | + P256o(tmp) | P256e(tmp) | P128o(tmp) | P128e(tmp)); + ecc_buf[2] = ~(P4o(tmp) | P4e(tmp) | P2o(tmp) | P2e(tmp) | P1o(tmp) | + P1e(tmp) | P2048o(tmp) | P2048e(tmp)); +} + +/** + * omap_compare_ecc - Detect (2 bits) and correct (1 bit) error in data + * @ecc_data1: ecc code from nand spare area + * @ecc_data2: ecc code from hardware register obtained from hardware ecc + * @page_data: page data + * + * This function compares two ECC's and indicates if there is an error. + * If the error can be corrected it will be corrected to the buffer. + * If there is no error, %0 is returned. If there is an error but it + * was corrected, %1 is returned. Otherwise, %-1 is returned. + */ +static int omap_compare_ecc(u8 *ecc_data1, /* read from NAND memory */ + u8 *ecc_data2, /* read from register */ + u8 *page_data) +{ + uint i; + u8 tmp0_bit[8], tmp1_bit[8], tmp2_bit[8]; + u8 comp0_bit[8], comp1_bit[8], comp2_bit[8]; + u8 ecc_bit[24]; + u8 ecc_sum = 0; + u8 find_bit = 0; + uint find_byte = 0; + int isEccFF; + + isEccFF = ((*(u32 *)ecc_data1 & 0xFFFFFF) == 0xFFFFFF); + + gen_true_ecc(ecc_data1); + gen_true_ecc(ecc_data2); + + for (i = 0; i <= 2; i++) { + *(ecc_data1 + i) = ~(*(ecc_data1 + i)); + *(ecc_data2 + i) = ~(*(ecc_data2 + i)); + } + + for (i = 0; i < 8; i++) { + tmp0_bit[i] = *ecc_data1 % 2; + *ecc_data1 = *ecc_data1 / 2; + } + + for (i = 0; i < 8; i++) { + tmp1_bit[i] = *(ecc_data1 + 1) % 2; + *(ecc_data1 + 1) = *(ecc_data1 + 1) / 2; + } + + for (i = 0; i < 8; i++) { + tmp2_bit[i] = *(ecc_data1 + 2) % 2; + *(ecc_data1 + 2) = *(ecc_data1 + 2) / 2; + } + + for (i = 0; i < 8; i++) { + comp0_bit[i] = *ecc_data2 % 2; + *ecc_data2 = *ecc_data2 / 2; + } + + for (i = 0; i < 8; i++) { + comp1_bit[i] = *(ecc_data2 + 1) % 2; + *(ecc_data2 + 1) = *(ecc_data2 + 1) / 2; + } + + for (i = 0; i < 8; i++) { + comp2_bit[i] = *(ecc_data2 + 2) % 2; + *(ecc_data2 + 2) = *(ecc_data2 + 2) / 2; + } + + for (i = 0; i < 6; i++) + ecc_bit[i] = tmp2_bit[i + 2] ^ comp2_bit[i + 2]; + + for (i = 0; i < 8; i++) + ecc_bit[i + 6] = tmp0_bit[i] ^ comp0_bit[i]; + + for (i = 0; i < 8; i++) + ecc_bit[i + 14] = tmp1_bit[i] ^ comp1_bit[i]; + + ecc_bit[22] = tmp2_bit[0] ^ comp2_bit[0]; + ecc_bit[23] = tmp2_bit[1] ^ comp2_bit[1]; + + for (i = 0; i < 24; i++) + ecc_sum += ecc_bit[i]; + + switch (ecc_sum) { + case 0: + /* Not reached because this function is not called if + * ECC values are equal + */ + return 0; + + case 1: + /* Uncorrectable error */ + pr_debug("ECC UNCORRECTED_ERROR 1\n"); + return -1; + + case 11: + /* UN-Correctable error */ + pr_debug("ECC UNCORRECTED_ERROR B\n"); + return -1; + + case 12: + /* Correctable error */ + find_byte = (ecc_bit[23] << 8) + + (ecc_bit[21] << 7) + + (ecc_bit[19] << 6) + + (ecc_bit[17] << 5) + + (ecc_bit[15] << 4) + + (ecc_bit[13] << 3) + + (ecc_bit[11] << 2) + + (ecc_bit[9] << 1) + + ecc_bit[7]; + + find_bit = (ecc_bit[5] << 2) + (ecc_bit[3] << 1) + ecc_bit[1]; + + pr_debug("Correcting single bit ECC error at offset: " + "%d, bit: %d\n", find_byte, find_bit); + + page_data[find_byte] ^= (1 << find_bit); + + return 1; + default: + if (isEccFF) { + if (ecc_data2[0] == 0 && + ecc_data2[1] == 0 && + ecc_data2[2] == 0) + return 0; + } + pr_debug("UNCORRECTED_ERROR default\n"); + return -1; + } +} + +/** + * omap_correct_data - Compares the ECC read with HW generated ECC + * @mtd: MTD device structure + * @dat: page data + * @read_ecc: ecc read from nand flash + * @calc_ecc: ecc read from HW ECC registers + * + * Compares the ecc read from nand spare area with ECC registers values + * and if ECC's mismatched, it will call 'omap_compare_ecc' for error + * detection and correction. If there are no errors, %0 is returned. If + * there were errors and all of the errors were corrected, the number of + * corrected errors is returned. If uncorrectable errors exist, %-1 is + * returned. + */ +static int omap_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + int blockCnt = 0, i = 0, ret = 0; + int stat = 0; + + /* Ex NAND_ECC_HW12_2048 */ + if ((info->nand.ecc.mode == NAND_ECC_HW) && + (info->nand.ecc.size == 2048)) + blockCnt = 4; + else + blockCnt = 1; + + for (i = 0; i < blockCnt; i++) { + if (memcmp(read_ecc, calc_ecc, 3) != 0) { + ret = omap_compare_ecc(read_ecc, calc_ecc, dat); + if (ret < 0) + return ret; + /* keep track of the number of corrected errors */ + stat += ret; + } + read_ecc += 3; + calc_ecc += 3; + dat += 512; + } + return stat; +} + +/** + * omap_calcuate_ecc - Generate non-inverted ECC bytes. + * @mtd: MTD device structure + * @dat: The pointer to data on which ecc is computed + * @ecc_code: The ecc_code buffer + * + * Using noninverted ECC can be considered ugly since writing a blank + * page ie. padding will clear the ECC bytes. This is no problem as long + * nobody is trying to write data on the seemingly unused page. Reading + * an erased page will produce an ECC mismatch between generated and read + * ECC bytes that has to be dealt with separately. + */ +static int omap_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + u32 val; + + val = readl(info->reg.gpmc_ecc_config); + if (((val >> ECC_CONFIG_CS_SHIFT) & CS_MASK) != info->gpmc_cs) + return -EINVAL; + + /* read ecc result */ + val = readl(info->reg.gpmc_ecc1_result); + *ecc_code++ = val; /* P128e, ..., P1e */ + *ecc_code++ = val >> 16; /* P128o, ..., P1o */ + /* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */ + *ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0); + + return 0; +} + +/** + * omap_enable_hwecc - This function enables the hardware ecc functionality + * @mtd: MTD device structure + * @mode: Read/Write mode + */ +static void omap_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + struct nand_chip *chip = mtd->priv; + unsigned int dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0; + u32 val; + + /* clear ecc and enable bits */ + val = ECCCLEAR | ECC1; + writel(val, info->reg.gpmc_ecc_control); + + /* program ecc and result sizes */ + val = ((((info->nand.ecc.size >> 1) - 1) << ECCSIZE1_SHIFT) | + ECC1RESULTSIZE); + writel(val, info->reg.gpmc_ecc_size_config); + + switch (mode) { + case NAND_ECC_READ: + case NAND_ECC_WRITE: + writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control); + break; + case NAND_ECC_READSYN: + writel(ECCCLEAR, info->reg.gpmc_ecc_control); + break; + default: + dev_info(&info->pdev->dev, + "error: unrecognized Mode[%d]!\n", mode); + break; + } + + /* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */ + val = (dev_width << 7) | (info->gpmc_cs << 1) | (0x1); + writel(val, info->reg.gpmc_ecc_config); +} + +/** + * omap_wait - wait until the command is done + * @mtd: MTD device structure + * @chip: NAND Chip structure + * + * Wait function is called during Program and erase operations and + * the way it is called from MTD layer, we should wait till the NAND + * chip is ready after the programming/erase operation has completed. + * + * Erase can take up to 400ms and program up to 20ms according to + * general NAND and SmartMedia specs + */ +static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct nand_chip *this = mtd->priv; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + unsigned long timeo = jiffies; + int status, state = this->state; + + if (state == FL_ERASING) + timeo += msecs_to_jiffies(400); + else + timeo += msecs_to_jiffies(20); + + writeb(NAND_CMD_STATUS & 0xFF, info->reg.gpmc_nand_command); + while (time_before(jiffies, timeo)) { + status = readb(info->reg.gpmc_nand_data); + if (status & NAND_STATUS_READY) + break; + cond_resched(); + } + + status = readb(info->reg.gpmc_nand_data); + return status; +} + +/** + * omap_dev_ready - calls the platform specific dev_ready function + * @mtd: MTD device structure + */ +static int omap_dev_ready(struct mtd_info *mtd) +{ + unsigned int val = 0; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + + val = readl(info->reg.gpmc_status); + + if ((val & 0x100) == 0x100) { + return 1; + } else { + return 0; + } +} + +/** + * omap_enable_hwecc_bch - Program GPMC to perform BCH ECC calculation + * @mtd: MTD device structure + * @mode: Read/Write mode + * + * When using BCH with SW correction (i.e. no ELM), sector size is set + * to 512 bytes and we use BCH_WRAPMODE_6 wrapping mode + * for both reading and writing with: + * eccsize0 = 0 (no additional protected byte in spare area) + * eccsize1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) + */ +static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info *mtd, int mode) +{ + unsigned int bch_type; + unsigned int dev_width, nsectors; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + enum omap_ecc ecc_opt = info->ecc_opt; + struct nand_chip *chip = mtd->priv; + u32 val, wr_mode; + unsigned int ecc_size1, ecc_size0; + + /* GPMC configurations for calculating ECC */ + switch (ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + bch_type = 0; + nsectors = 1; + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + break; + case OMAP_ECC_BCH4_CODE_HW: + bch_type = 0; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_1; + ecc_size0 = BCH4R_ECC_SIZE0; + ecc_size1 = BCH4R_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + bch_type = 1; + nsectors = 1; + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + break; + case OMAP_ECC_BCH8_CODE_HW: + bch_type = 1; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = BCH_WRAPMODE_1; + ecc_size0 = BCH8R_ECC_SIZE0; + ecc_size1 = BCH8R_ECC_SIZE1; + } else { + wr_mode = BCH_WRAPMODE_6; + ecc_size0 = BCH_ECC_SIZE0; + ecc_size1 = BCH_ECC_SIZE1; + } + break; + case OMAP_ECC_BCH16_CODE_HW: + bch_type = 0x2; + nsectors = chip->ecc.steps; + if (mode == NAND_ECC_READ) { + wr_mode = 0x01; + ecc_size0 = 52; /* ECC bits in nibbles per sector */ + ecc_size1 = 0; /* non-ECC bits in nibbles per sector */ + } else { + wr_mode = 0x01; + ecc_size0 = 0; /* extra bits in nibbles per sector */ + ecc_size1 = 52; /* OOB bits in nibbles per sector */ + } + break; + default: + return; + } + + writel(ECC1, info->reg.gpmc_ecc_control); + + /* Configure ecc size for BCH */ + val = (ecc_size1 << ECCSIZE1_SHIFT) | (ecc_size0 << ECCSIZE0_SHIFT); + writel(val, info->reg.gpmc_ecc_size_config); + + dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0; + + /* BCH configuration */ + val = ((1 << 16) | /* enable BCH */ + (bch_type << 12) | /* BCH4/BCH8/BCH16 */ + (wr_mode << 8) | /* wrap mode */ + (dev_width << 7) | /* bus width */ + (((nsectors-1) & 0x7) << 4) | /* number of sectors */ + (info->gpmc_cs << 1) | /* ECC CS */ + (0x1)); /* enable ECC */ + + writel(val, info->reg.gpmc_ecc_config); + + /* Clear ecc and enable bits */ + writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control); +} + +static u8 bch4_polynomial[] = {0x28, 0x13, 0xcc, 0x39, 0x96, 0xac, 0x7f}; +static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2, + 0x97, 0x79, 0xe5, 0x24, 0xb5}; + +/** + * omap_calculate_ecc_bch - Generate bytes of ECC bytes + * @mtd: MTD device structure + * @dat: The pointer to data on which ecc is computed + * @ecc_code: The ecc_code buffer + * + * Support calculating of BCH4/8 ecc vectors for the page + */ +static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd, + const u_char *dat, u_char *ecc_calc) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + int eccbytes = info->nand.ecc.bytes; + struct gpmc_nand_regs *gpmc_regs = &info->reg; + u8 *ecc_code; + unsigned long nsectors, bch_val1, bch_val2, bch_val3, bch_val4; + u32 val; + int i, j; + + nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1; + for (i = 0; i < nsectors; i++) { + ecc_code = ecc_calc; + switch (info->ecc_opt) { + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH8_CODE_HW: + bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]); + bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]); + bch_val3 = readl(gpmc_regs->gpmc_bch_result2[i]); + bch_val4 = readl(gpmc_regs->gpmc_bch_result3[i]); + *ecc_code++ = (bch_val4 & 0xFF); + *ecc_code++ = ((bch_val3 >> 24) & 0xFF); + *ecc_code++ = ((bch_val3 >> 16) & 0xFF); + *ecc_code++ = ((bch_val3 >> 8) & 0xFF); + *ecc_code++ = (bch_val3 & 0xFF); + *ecc_code++ = ((bch_val2 >> 24) & 0xFF); + *ecc_code++ = ((bch_val2 >> 16) & 0xFF); + *ecc_code++ = ((bch_val2 >> 8) & 0xFF); + *ecc_code++ = (bch_val2 & 0xFF); + *ecc_code++ = ((bch_val1 >> 24) & 0xFF); + *ecc_code++ = ((bch_val1 >> 16) & 0xFF); + *ecc_code++ = ((bch_val1 >> 8) & 0xFF); + *ecc_code++ = (bch_val1 & 0xFF); + break; + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH4_CODE_HW: + bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]); + bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]); + *ecc_code++ = ((bch_val2 >> 12) & 0xFF); + *ecc_code++ = ((bch_val2 >> 4) & 0xFF); + *ecc_code++ = ((bch_val2 & 0xF) << 4) | + ((bch_val1 >> 28) & 0xF); + *ecc_code++ = ((bch_val1 >> 20) & 0xFF); + *ecc_code++ = ((bch_val1 >> 12) & 0xFF); + *ecc_code++ = ((bch_val1 >> 4) & 0xFF); + *ecc_code++ = ((bch_val1 & 0xF) << 4); + break; + case OMAP_ECC_BCH16_CODE_HW: + val = readl(gpmc_regs->gpmc_bch_result6[i]); + ecc_code[0] = ((val >> 8) & 0xFF); + ecc_code[1] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result5[i]); + ecc_code[2] = ((val >> 24) & 0xFF); + ecc_code[3] = ((val >> 16) & 0xFF); + ecc_code[4] = ((val >> 8) & 0xFF); + ecc_code[5] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result4[i]); + ecc_code[6] = ((val >> 24) & 0xFF); + ecc_code[7] = ((val >> 16) & 0xFF); + ecc_code[8] = ((val >> 8) & 0xFF); + ecc_code[9] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result3[i]); + ecc_code[10] = ((val >> 24) & 0xFF); + ecc_code[11] = ((val >> 16) & 0xFF); + ecc_code[12] = ((val >> 8) & 0xFF); + ecc_code[13] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result2[i]); + ecc_code[14] = ((val >> 24) & 0xFF); + ecc_code[15] = ((val >> 16) & 0xFF); + ecc_code[16] = ((val >> 8) & 0xFF); + ecc_code[17] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result1[i]); + ecc_code[18] = ((val >> 24) & 0xFF); + ecc_code[19] = ((val >> 16) & 0xFF); + ecc_code[20] = ((val >> 8) & 0xFF); + ecc_code[21] = ((val >> 0) & 0xFF); + val = readl(gpmc_regs->gpmc_bch_result0[i]); + ecc_code[22] = ((val >> 24) & 0xFF); + ecc_code[23] = ((val >> 16) & 0xFF); + ecc_code[24] = ((val >> 8) & 0xFF); + ecc_code[25] = ((val >> 0) & 0xFF); + break; + default: + return -EINVAL; + } + + /* ECC scheme specific syndrome customizations */ + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + /* Add constant polynomial to remainder, so that + * ECC of blank pages results in 0x0 on reading back */ + for (j = 0; j < eccbytes; j++) + ecc_calc[j] ^= bch4_polynomial[j]; + break; + case OMAP_ECC_BCH4_CODE_HW: + /* Set 8th ECC byte as 0x0 for ROM compatibility */ + ecc_calc[eccbytes - 1] = 0x0; + break; + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + /* Add constant polynomial to remainder, so that + * ECC of blank pages results in 0x0 on reading back */ + for (j = 0; j < eccbytes; j++) + ecc_calc[j] ^= bch8_polynomial[j]; + break; + case OMAP_ECC_BCH8_CODE_HW: + /* Set 14th ECC byte as 0x0 for ROM compatibility */ + ecc_calc[eccbytes - 1] = 0x0; + break; + case OMAP_ECC_BCH16_CODE_HW: + break; + default: + return -EINVAL; + } + + ecc_calc += eccbytes; + } + + return 0; +} + +/** + * erased_sector_bitflips - count bit flips + * @data: data sector buffer + * @oob: oob buffer + * @info: omap_nand_info + * + * Check the bit flips in erased page falls below correctable level. + * If falls below, report the page as erased with correctable bit + * flip, else report as uncorrectable page. + */ +static int erased_sector_bitflips(u_char *data, u_char *oob, + struct omap_nand_info *info) +{ + int flip_bits = 0, i; + + for (i = 0; i < info->nand.ecc.size; i++) { + flip_bits += hweight8(~data[i]); + if (flip_bits > info->nand.ecc.strength) + return 0; + } + + for (i = 0; i < info->nand.ecc.bytes - 1; i++) { + flip_bits += hweight8(~oob[i]); + if (flip_bits > info->nand.ecc.strength) + return 0; + } + + /* + * Bit flips falls in correctable level. + * Fill data area with 0xFF + */ + if (flip_bits) { + memset(data, 0xFF, info->nand.ecc.size); + memset(oob, 0xFF, info->nand.ecc.bytes); + } + + return flip_bits; +} + +/** + * omap_elm_correct_data - corrects page data area in case error reported + * @mtd: MTD device structure + * @data: page data + * @read_ecc: ecc read from nand flash + * @calc_ecc: ecc read from HW ECC registers + * + * Calculated ecc vector reported as zero in case of non-error pages. + * In case of non-zero ecc vector, first filter out erased-pages, and + * then process data via ELM to detect bit-flips. + */ +static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, + u_char *read_ecc, u_char *calc_ecc) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + struct nand_ecc_ctrl *ecc = &info->nand.ecc; + int eccsteps = info->nand.ecc.steps; + int i , j, stat = 0; + int eccflag, actual_eccbytes; + struct elm_errorvec err_vec[ERROR_VECTOR_MAX]; + u_char *ecc_vec = calc_ecc; + u_char *spare_ecc = read_ecc; + u_char *erased_ecc_vec; + u_char *buf; + int bitflip_count; + bool is_error_reported = false; + u32 bit_pos, byte_pos, error_max, pos; + int err; + + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW: + /* omit 7th ECC byte reserved for ROM code compatibility */ + actual_eccbytes = ecc->bytes - 1; + erased_ecc_vec = bch4_vector; + break; + case OMAP_ECC_BCH8_CODE_HW: + /* omit 14th ECC byte reserved for ROM code compatibility */ + actual_eccbytes = ecc->bytes - 1; + erased_ecc_vec = bch8_vector; + break; + case OMAP_ECC_BCH16_CODE_HW: + actual_eccbytes = ecc->bytes; + erased_ecc_vec = bch16_vector; + break; + default: + dev_err(&info->pdev->dev, "invalid driver configuration\n"); + return -EINVAL; + } + + /* Initialize elm error vector to zero */ + memset(err_vec, 0, sizeof(err_vec)); + + for (i = 0; i < eccsteps ; i++) { + eccflag = 0; /* initialize eccflag */ + + /* + * Check any error reported, + * In case of error, non zero ecc reported. + */ + for (j = 0; j < actual_eccbytes; j++) { + if (calc_ecc[j] != 0) { + eccflag = 1; /* non zero ecc, error present */ + break; + } + } + + if (eccflag == 1) { + if (memcmp(calc_ecc, erased_ecc_vec, + actual_eccbytes) == 0) { + /* + * calc_ecc[] matches pattern for ECC(all 0xff) + * so this is definitely an erased-page + */ + } else { + buf = &data[info->nand.ecc.size * i]; + /* + * count number of 0-bits in read_buf. + * This check can be removed once a similar + * check is introduced in generic NAND driver + */ + bitflip_count = erased_sector_bitflips( + buf, read_ecc, info); + if (bitflip_count) { + /* + * number of 0-bits within ECC limits + * So this may be an erased-page + */ + stat += bitflip_count; + } else { + /* + * Too many 0-bits. It may be a + * - programmed-page, OR + * - erased-page with many bit-flips + * So this page requires check by ELM + */ + err_vec[i].error_reported = true; + is_error_reported = true; + } + } + } + + /* Update the ecc vector */ + calc_ecc += ecc->bytes; + read_ecc += ecc->bytes; + } + + /* Check if any error reported */ + if (!is_error_reported) + return stat; + + /* Decode BCH error using ELM module */ + elm_decode_bch_error_page(info->elm_dev, ecc_vec, err_vec); + + err = 0; + for (i = 0; i < eccsteps; i++) { + if (err_vec[i].error_uncorrectable) { + dev_err(&info->pdev->dev, + "uncorrectable bit-flips found\n"); + err = -EBADMSG; + } else if (err_vec[i].error_reported) { + for (j = 0; j < err_vec[i].error_count; j++) { + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW: + /* Add 4 bits to take care of padding */ + pos = err_vec[i].error_loc[j] + + BCH4_BIT_PAD; + break; + case OMAP_ECC_BCH8_CODE_HW: + case OMAP_ECC_BCH16_CODE_HW: + pos = err_vec[i].error_loc[j]; + break; + default: + return -EINVAL; + } + error_max = (ecc->size + actual_eccbytes) * 8; + /* Calculate bit position of error */ + bit_pos = pos % 8; + + /* Calculate byte position of error */ + byte_pos = (error_max - pos - 1) / 8; + + if (pos < error_max) { + if (byte_pos < 512) { + pr_debug("bitflip@dat[%d]=%x\n", + byte_pos, data[byte_pos]); + data[byte_pos] ^= 1 << bit_pos; + } else { + pr_debug("bitflip@oob[%d]=%x\n", + (byte_pos - 512), + spare_ecc[byte_pos - 512]); + spare_ecc[byte_pos - 512] ^= + 1 << bit_pos; + } + } else { + dev_err(&info->pdev->dev, + "invalid bit-flip @ %d:%d\n", + byte_pos, bit_pos); + err = -EBADMSG; + } + } + } + + /* Update number of correctable errors */ + stat += err_vec[i].error_count; + + /* Update page data with sector size */ + data += ecc->size; + spare_ecc += ecc->bytes; + } + + return (err) ? err : stat; +} + +/** + * omap_write_page_bch - BCH ecc based write page function for entire page + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * + * Custom write page method evolved to support multi sector writing in one shot + */ +static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + int i; + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint32_t *eccpos = chip->ecc.layout->eccpos; + + /* Enable GPMC ecc engine */ + chip->ecc.hwctl(mtd, NAND_ECC_WRITE); + + /* Write data */ + chip->write_buf(mtd, buf, mtd->writesize); + + /* Update ecc vector from GPMC result registers */ + chip->ecc.calculate(mtd, buf, &ecc_calc[0]); + + for (i = 0; i < chip->ecc.total; i++) + chip->oob_poi[eccpos[i]] = ecc_calc[i]; + + /* Write ecc vector to OOB area */ + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +/** + * omap_read_page_bch - BCH ecc based page read function for entire page + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * For BCH ecc scheme, GPMC used for syndrome calculation and ELM module + * used for error correction. + * Custom method evolved to support ELM error correction & multi sector + * reading. On reading page data area is read along with OOB data with + * ecc engine enabled. ecc vector updated after read of OOB data. + * For non error pages ecc vector reported as zero. + */ +static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->buffers->ecccode; + uint32_t *eccpos = chip->ecc.layout->eccpos; + uint8_t *oob = &chip->oob_poi[eccpos[0]]; + uint32_t oob_pos = mtd->writesize + chip->ecc.layout->eccpos[0]; + int stat; + unsigned int max_bitflips = 0; + + /* Enable GPMC ecc engine */ + chip->ecc.hwctl(mtd, NAND_ECC_READ); + + /* Read data */ + chip->read_buf(mtd, buf, mtd->writesize); + + /* Read oob bytes */ + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, -1); + chip->read_buf(mtd, oob, chip->ecc.total); + + /* Calculate ecc bytes */ + chip->ecc.calculate(mtd, buf, ecc_calc); + + memcpy(ecc_code, &chip->oob_poi[eccpos[0]], chip->ecc.total); + + stat = chip->ecc.correct(mtd, buf, ecc_code, ecc_calc); + + if (stat < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += stat; + max_bitflips = max_t(unsigned int, max_bitflips, stat); + } + + return max_bitflips; +} + +/** + * is_elm_present - checks for presence of ELM module by scanning DT nodes + * @omap_nand_info: NAND device structure containing platform data + */ +static bool is_elm_present(struct omap_nand_info *info, + struct device_node *elm_node) +{ + struct platform_device *pdev; + + /* check whether elm-id is passed via DT */ + if (!elm_node) { + dev_err(&info->pdev->dev, "ELM devicetree node not found\n"); + return false; + } + pdev = of_find_device_by_node(elm_node); + /* check whether ELM device is registered */ + if (!pdev) { + dev_err(&info->pdev->dev, "ELM device not found\n"); + return false; + } + /* ELM module available, now configure it */ + info->elm_dev = &pdev->dev; + return true; +} + +static bool omap2_nand_ecc_check(struct omap_nand_info *info, + struct omap_nand_platform_data *pdata) +{ + bool ecc_needs_bch, ecc_needs_omap_bch, ecc_needs_elm; + + switch (info->ecc_opt) { + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + ecc_needs_omap_bch = false; + ecc_needs_bch = true; + ecc_needs_elm = false; + break; + case OMAP_ECC_BCH4_CODE_HW: + case OMAP_ECC_BCH8_CODE_HW: + case OMAP_ECC_BCH16_CODE_HW: + ecc_needs_omap_bch = true; + ecc_needs_bch = false; + ecc_needs_elm = true; + break; + default: + ecc_needs_omap_bch = false; + ecc_needs_bch = false; + ecc_needs_elm = false; + break; + } + + if (ecc_needs_bch && !IS_ENABLED(CONFIG_MTD_NAND_ECC_BCH)) { + dev_err(&info->pdev->dev, + "CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + return false; + } + if (ecc_needs_omap_bch && !IS_ENABLED(CONFIG_MTD_NAND_OMAP_BCH)) { + dev_err(&info->pdev->dev, + "CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + return false; + } + if (ecc_needs_elm && !is_elm_present(info, pdata->elm_of_node)) { + dev_err(&info->pdev->dev, "ELM not available\n"); + return false; + } + + return true; +} + +static int omap_nand_probe(struct platform_device *pdev) +{ + struct omap_nand_info *info; + struct omap_nand_platform_data *pdata; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + struct nand_ecclayout *ecclayout; + int err; + int i; + dma_cap_mask_t mask; + unsigned sig; + unsigned oob_index; + struct resource *res; + struct mtd_part_parser_data ppdata = {}; + + pdata = dev_get_platdata(&pdev->dev); + if (pdata == NULL) { + dev_err(&pdev->dev, "platform data missing\n"); + return -ENODEV; + } + + info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info), + GFP_KERNEL); + if (!info) + return -ENOMEM; + + platform_set_drvdata(pdev, info); + + info->pdev = pdev; + info->gpmc_cs = pdata->cs; + info->reg = pdata->reg; + info->of_node = pdata->of_node; + info->ecc_opt = pdata->ecc_opt; + mtd = &info->mtd; + mtd->priv = &info->nand; + mtd->name = dev_name(&pdev->dev); + mtd->owner = THIS_MODULE; + nand_chip = &info->nand; + nand_chip->ecc.priv = NULL; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nand_chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(nand_chip->IO_ADDR_R)) + return PTR_ERR(nand_chip->IO_ADDR_R); + + info->phys_base = res->start; + + nand_chip->controller = &omap_gpmc_controller; + + nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R; + nand_chip->cmd_ctrl = omap_hwcontrol; + + /* + * If RDY/BSY line is connected to OMAP then use the omap ready + * function and the generic nand_wait function which reads the status + * register after monitoring the RDY/BSY line. Otherwise use a standard + * chip delay which is slightly more than tR (AC Timing) of the NAND + * device and read status register until you get a failure or success + */ + if (pdata->dev_ready) { + nand_chip->dev_ready = omap_dev_ready; + nand_chip->chip_delay = 0; + } else { + nand_chip->waitfunc = omap_wait; + nand_chip->chip_delay = 50; + } + + if (pdata->flash_bbt) + nand_chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; + else + nand_chip->options |= NAND_SKIP_BBTSCAN; + + /* scan NAND device connected to chip controller */ + nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16; + if (nand_scan_ident(mtd, 1, NULL)) { + dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n"); + err = -ENXIO; + goto return_error; + } + + /* re-populate low-level callbacks based on xfer modes */ + switch (pdata->xfer_type) { + case NAND_OMAP_PREFETCH_POLLED: + nand_chip->read_buf = omap_read_buf_pref; + nand_chip->write_buf = omap_write_buf_pref; + break; + + case NAND_OMAP_POLLED: + /* Use nand_base defaults for {read,write}_buf */ + break; + + case NAND_OMAP_PREFETCH_DMA: + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + sig = OMAP24XX_DMA_GPMC; + info->dma = dma_request_channel(mask, omap_dma_filter_fn, &sig); + if (!info->dma) { + dev_err(&pdev->dev, "DMA engine request failed\n"); + err = -ENXIO; + goto return_error; + } else { + struct dma_slave_config cfg; + + memset(&cfg, 0, sizeof(cfg)); + cfg.src_addr = info->phys_base; + cfg.dst_addr = info->phys_base; + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + cfg.src_maxburst = 16; + cfg.dst_maxburst = 16; + err = dmaengine_slave_config(info->dma, &cfg); + if (err) { + dev_err(&pdev->dev, "DMA engine slave config failed: %d\n", + err); + goto return_error; + } + nand_chip->read_buf = omap_read_buf_dma_pref; + nand_chip->write_buf = omap_write_buf_dma_pref; + } + break; + + case NAND_OMAP_PREFETCH_IRQ: + info->gpmc_irq_fifo = platform_get_irq(pdev, 0); + if (info->gpmc_irq_fifo <= 0) { + dev_err(&pdev->dev, "error getting fifo irq\n"); + err = -ENODEV; + goto return_error; + } + err = devm_request_irq(&pdev->dev, info->gpmc_irq_fifo, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-fifo", info); + if (err) { + dev_err(&pdev->dev, "requesting irq(%d) error:%d", + info->gpmc_irq_fifo, err); + info->gpmc_irq_fifo = 0; + goto return_error; + } + + info->gpmc_irq_count = platform_get_irq(pdev, 1); + if (info->gpmc_irq_count <= 0) { + dev_err(&pdev->dev, "error getting count irq\n"); + err = -ENODEV; + goto return_error; + } + err = devm_request_irq(&pdev->dev, info->gpmc_irq_count, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-count", info); + if (err) { + dev_err(&pdev->dev, "requesting irq(%d) error:%d", + info->gpmc_irq_count, err); + info->gpmc_irq_count = 0; + goto return_error; + } + + nand_chip->read_buf = omap_read_buf_irq_pref; + nand_chip->write_buf = omap_write_buf_irq_pref; + + break; + + default: + dev_err(&pdev->dev, + "xfer_type(%d) not supported!\n", pdata->xfer_type); + err = -EINVAL; + goto return_error; + } + + if (!omap2_nand_ecc_check(info, pdata)) { + err = -EINVAL; + goto return_error; + } + + /* populate MTD interface based on ECC scheme */ + ecclayout = &info->oobinfo; + switch (info->ecc_opt) { + case OMAP_ECC_HAM1_CODE_SW: + nand_chip->ecc.mode = NAND_ECC_SOFT; + break; + + case OMAP_ECC_HAM1_CODE_HW: + pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.bytes = 3; + nand_chip->ecc.size = 512; + nand_chip->ecc.strength = 1; + nand_chip->ecc.calculate = omap_calculate_ecc; + nand_chip->ecc.hwctl = omap_enable_hwecc; + nand_chip->ecc.correct = omap_correct_data; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + if (nand_chip->options & NAND_BUSWIDTH_16) + oob_index = BADBLOCK_MARKER_LENGTH; + else + oob_index = 1; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* no reserved-marker in ecclayout for this ecc-scheme */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; + + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 7; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; + } + /* include reserved-marker in ecclayout->oobfree calculation */ + ecclayout->oobfree->offset = 1 + + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &ecclayout); + if (!nand_chip->ecc.priv) { + dev_err(&info->pdev->dev, "unable to use BCH library\n"); + err = -EINVAL; + goto return_error; + } + break; + + case OMAP_ECC_BCH4_CODE_HW: + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 7 + 1; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + + err = elm_config(info->elm_dev, BCH4_ECC, + info->mtd.writesize / nand_chip->ecc.size, + nand_chip->ecc.size, nand_chip->ecc.bytes); + if (err < 0) + goto return_error; + break; + + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 13; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) { + ecclayout->eccpos[i] = oob_index; + if (((i + 1) % nand_chip->ecc.bytes) == 0) + oob_index++; + } + /* include reserved-marker in ecclayout->oobfree calculation */ + ecclayout->oobfree->offset = 1 + + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &ecclayout); + if (!nand_chip->ecc.priv) { + dev_err(&info->pdev->dev, "unable to use BCH library\n"); + err = -EINVAL; + goto return_error; + } + break; + + case OMAP_ECC_BCH8_CODE_HW: + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 13 + 1; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + + err = elm_config(info->elm_dev, BCH8_ECC, + info->mtd.writesize / nand_chip->ecc.size, + nand_chip->ecc.size, nand_chip->ecc.bytes); + if (err < 0) + goto return_error; + + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; + + case OMAP_ECC_BCH16_CODE_HW: + pr_info("using OMAP_ECC_BCH16_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 26; + nand_chip->ecc.strength = 16; + nand_chip->ecc.hwctl = omap_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + + err = elm_config(info->elm_dev, BCH16_ECC, + info->mtd.writesize / nand_chip->ecc.size, + nand_chip->ecc.size, nand_chip->ecc.bytes); + if (err < 0) + goto return_error; + + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + oob_index = BADBLOCK_MARKER_LENGTH; + for (i = 0; i < ecclayout->eccbytes; i++, oob_index++) + ecclayout->eccpos[i] = oob_index; + /* reserved marker already included in ecclayout->eccbytes */ + ecclayout->oobfree->offset = + ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; + break; + default: + dev_err(&info->pdev->dev, "invalid or unsupported ECC scheme\n"); + err = -EINVAL; + goto return_error; + } + + if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW) + goto scan_tail; + + /* all OOB bytes from oobfree->offset till end off OOB are free */ + ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset; + /* check if NAND device's OOB is enough to store ECC signatures */ + if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) { + dev_err(&info->pdev->dev, + "not enough OOB bytes required = %d, available=%d\n", + ecclayout->eccbytes, mtd->oobsize); + err = -EINVAL; + goto return_error; + } + nand_chip->ecc.layout = ecclayout; + +scan_tail: + /* second phase scan */ + if (nand_scan_tail(mtd)) { + err = -ENXIO; + goto return_error; + } + + ppdata.of_node = pdata->of_node; + mtd_device_parse_register(mtd, NULL, &ppdata, pdata->parts, + pdata->nr_parts); + + platform_set_drvdata(pdev, mtd); + + return 0; + +return_error: + if (info->dma) + dma_release_channel(info->dma); + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } + return err; +} + +static int omap_nand_remove(struct platform_device *pdev) +{ + struct mtd_info *mtd = platform_get_drvdata(pdev); + struct nand_chip *nand_chip = mtd->priv; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } + if (info->dma) + dma_release_channel(info->dma); + nand_release(mtd); + return 0; +} + +static struct platform_driver omap_nand_driver = { + .probe = omap_nand_probe, + .remove = omap_nand_remove, + .driver = { + .name = DRIVER_NAME, + }, +}; + +module_platform_driver(omap_nand_driver); + +MODULE_ALIAS("platform:" DRIVER_NAME); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Glue layer for NAND flash on TI OMAP boards"); diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/omap_elm.c new file mode 100644 index 000000000..376bfe191 --- /dev/null +++ b/drivers/mtd/nand/omap_elm.c @@ -0,0 +1,578 @@ +/* + * Error Location Module + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#define DRIVER_NAME "omap-elm" + +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/sched.h> +#include <linux/pm_runtime.h> +#include <linux/platform_data/elm.h> + +#define ELM_SYSCONFIG 0x010 +#define ELM_IRQSTATUS 0x018 +#define ELM_IRQENABLE 0x01c +#define ELM_LOCATION_CONFIG 0x020 +#define ELM_PAGE_CTRL 0x080 +#define ELM_SYNDROME_FRAGMENT_0 0x400 +#define ELM_SYNDROME_FRAGMENT_1 0x404 +#define ELM_SYNDROME_FRAGMENT_2 0x408 +#define ELM_SYNDROME_FRAGMENT_3 0x40c +#define ELM_SYNDROME_FRAGMENT_4 0x410 +#define ELM_SYNDROME_FRAGMENT_5 0x414 +#define ELM_SYNDROME_FRAGMENT_6 0x418 +#define ELM_LOCATION_STATUS 0x800 +#define ELM_ERROR_LOCATION_0 0x880 + +/* ELM Interrupt Status Register */ +#define INTR_STATUS_PAGE_VALID BIT(8) + +/* ELM Interrupt Enable Register */ +#define INTR_EN_PAGE_MASK BIT(8) + +/* ELM Location Configuration Register */ +#define ECC_BCH_LEVEL_MASK 0x3 + +/* ELM syndrome */ +#define ELM_SYNDROME_VALID BIT(16) + +/* ELM_LOCATION_STATUS Register */ +#define ECC_CORRECTABLE_MASK BIT(8) +#define ECC_NB_ERRORS_MASK 0x1f + +/* ELM_ERROR_LOCATION_0-15 Registers */ +#define ECC_ERROR_LOCATION_MASK 0x1fff + +#define ELM_ECC_SIZE 0x7ff + +#define SYNDROME_FRAGMENT_REG_SIZE 0x40 +#define ERROR_LOCATION_SIZE 0x100 + +struct elm_registers { + u32 elm_irqenable; + u32 elm_sysconfig; + u32 elm_location_config; + u32 elm_page_ctrl; + u32 elm_syndrome_fragment_6[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_5[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_4[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_3[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_2[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_1[ERROR_VECTOR_MAX]; + u32 elm_syndrome_fragment_0[ERROR_VECTOR_MAX]; +}; + +struct elm_info { + struct device *dev; + void __iomem *elm_base; + struct completion elm_completion; + struct list_head list; + enum bch_ecc bch_type; + struct elm_registers elm_regs; + int ecc_steps; + int ecc_syndrome_size; +}; + +static LIST_HEAD(elm_devices); + +static void elm_write_reg(struct elm_info *info, int offset, u32 val) +{ + writel(val, info->elm_base + offset); +} + +static u32 elm_read_reg(struct elm_info *info, int offset) +{ + return readl(info->elm_base + offset); +} + +/** + * elm_config - Configure ELM module + * @dev: ELM device + * @bch_type: Type of BCH ecc + */ +int elm_config(struct device *dev, enum bch_ecc bch_type, + int ecc_steps, int ecc_step_size, int ecc_syndrome_size) +{ + u32 reg_val; + struct elm_info *info = dev_get_drvdata(dev); + + if (!info) { + dev_err(dev, "Unable to configure elm - device not probed?\n"); + return -EPROBE_DEFER; + } + /* ELM cannot detect ECC errors for chunks > 1KB */ + if (ecc_step_size > ((ELM_ECC_SIZE + 1) / 2)) { + dev_err(dev, "unsupported config ecc-size=%d\n", ecc_step_size); + return -EINVAL; + } + /* ELM support 8 error syndrome process */ + if (ecc_steps > ERROR_VECTOR_MAX) { + dev_err(dev, "unsupported config ecc-step=%d\n", ecc_steps); + return -EINVAL; + } + + reg_val = (bch_type & ECC_BCH_LEVEL_MASK) | (ELM_ECC_SIZE << 16); + elm_write_reg(info, ELM_LOCATION_CONFIG, reg_val); + info->bch_type = bch_type; + info->ecc_steps = ecc_steps; + info->ecc_syndrome_size = ecc_syndrome_size; + + return 0; +} +EXPORT_SYMBOL(elm_config); + +/** + * elm_configure_page_mode - Enable/Disable page mode + * @info: elm info + * @index: index number of syndrome fragment vector + * @enable: enable/disable flag for page mode + * + * Enable page mode for syndrome fragment index + */ +static void elm_configure_page_mode(struct elm_info *info, int index, + bool enable) +{ + u32 reg_val; + + reg_val = elm_read_reg(info, ELM_PAGE_CTRL); + if (enable) + reg_val |= BIT(index); /* enable page mode */ + else + reg_val &= ~BIT(index); /* disable page mode */ + + elm_write_reg(info, ELM_PAGE_CTRL, reg_val); +} + +/** + * elm_load_syndrome - Load ELM syndrome reg + * @info: elm info + * @err_vec: elm error vectors + * @ecc: buffer with calculated ecc + * + * Load syndrome fragment registers with calculated ecc in reverse order. + */ +static void elm_load_syndrome(struct elm_info *info, + struct elm_errorvec *err_vec, u8 *ecc) +{ + int i, offset; + u32 val; + + for (i = 0; i < info->ecc_steps; i++) { + + /* Check error reported */ + if (err_vec[i].error_reported) { + elm_configure_page_mode(info, i, true); + offset = ELM_SYNDROME_FRAGMENT_0 + + SYNDROME_FRAGMENT_REG_SIZE * i; + switch (info->bch_type) { + case BCH8_ECC: + /* syndrome fragment 0 = ecc[9-12B] */ + val = cpu_to_be32(*(u32 *) &ecc[9]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 1 = ecc[5-8B] */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[5]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 2 = ecc[1-4B] */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[1]); + elm_write_reg(info, offset, val); + + /* syndrome fragment 3 = ecc[0B] */ + offset += 4; + val = ecc[0]; + elm_write_reg(info, offset, val); + break; + case BCH4_ECC: + /* syndrome fragment 0 = ecc[20-52b] bits */ + val = (cpu_to_be32(*(u32 *) &ecc[3]) >> 4) | + ((ecc[2] & 0xf) << 28); + elm_write_reg(info, offset, val); + + /* syndrome fragment 1 = ecc[0-20b] bits */ + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[0]) >> 12; + elm_write_reg(info, offset, val); + break; + case BCH16_ECC: + val = cpu_to_be32(*(u32 *) &ecc[22]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[18]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[14]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[10]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[6]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[2]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[0]) >> 16; + elm_write_reg(info, offset, val); + break; + default: + pr_err("invalid config bch_type\n"); + } + } + + /* Update ecc pointer with ecc byte size */ + ecc += info->ecc_syndrome_size; + } +} + +/** + * elm_start_processing - start elm syndrome processing + * @info: elm info + * @err_vec: elm error vectors + * + * Set syndrome valid bit for syndrome fragment registers for which + * elm syndrome fragment registers are loaded. This enables elm module + * to start processing syndrome vectors. + */ +static void elm_start_processing(struct elm_info *info, + struct elm_errorvec *err_vec) +{ + int i, offset; + u32 reg_val; + + /* + * Set syndrome vector valid, so that ELM module + * will process it for vectors error is reported + */ + for (i = 0; i < info->ecc_steps; i++) { + if (err_vec[i].error_reported) { + offset = ELM_SYNDROME_FRAGMENT_6 + + SYNDROME_FRAGMENT_REG_SIZE * i; + reg_val = elm_read_reg(info, offset); + reg_val |= ELM_SYNDROME_VALID; + elm_write_reg(info, offset, reg_val); + } + } +} + +/** + * elm_error_correction - locate correctable error position + * @info: elm info + * @err_vec: elm error vectors + * + * On completion of processing by elm module, error location status + * register updated with correctable/uncorrectable error information. + * In case of correctable errors, number of errors located from + * elm location status register & read the positions from + * elm error location register. + */ +static void elm_error_correction(struct elm_info *info, + struct elm_errorvec *err_vec) +{ + int i, j, errors = 0; + int offset; + u32 reg_val; + + for (i = 0; i < info->ecc_steps; i++) { + + /* Check error reported */ + if (err_vec[i].error_reported) { + offset = ELM_LOCATION_STATUS + ERROR_LOCATION_SIZE * i; + reg_val = elm_read_reg(info, offset); + + /* Check correctable error or not */ + if (reg_val & ECC_CORRECTABLE_MASK) { + offset = ELM_ERROR_LOCATION_0 + + ERROR_LOCATION_SIZE * i; + + /* Read count of correctable errors */ + err_vec[i].error_count = reg_val & + ECC_NB_ERRORS_MASK; + + /* Update the error locations in error vector */ + for (j = 0; j < err_vec[i].error_count; j++) { + + reg_val = elm_read_reg(info, offset); + err_vec[i].error_loc[j] = reg_val & + ECC_ERROR_LOCATION_MASK; + + /* Update error location register */ + offset += 4; + } + + errors += err_vec[i].error_count; + } else { + err_vec[i].error_uncorrectable = true; + } + + /* Clearing interrupts for processed error vectors */ + elm_write_reg(info, ELM_IRQSTATUS, BIT(i)); + + /* Disable page mode */ + elm_configure_page_mode(info, i, false); + } + } +} + +/** + * elm_decode_bch_error_page - Locate error position + * @dev: device pointer + * @ecc_calc: calculated ECC bytes from GPMC + * @err_vec: elm error vectors + * + * Called with one or more error reported vectors & vectors with + * error reported is updated in err_vec[].error_reported + */ +void elm_decode_bch_error_page(struct device *dev, u8 *ecc_calc, + struct elm_errorvec *err_vec) +{ + struct elm_info *info = dev_get_drvdata(dev); + u32 reg_val; + + /* Enable page mode interrupt */ + reg_val = elm_read_reg(info, ELM_IRQSTATUS); + elm_write_reg(info, ELM_IRQSTATUS, reg_val & INTR_STATUS_PAGE_VALID); + elm_write_reg(info, ELM_IRQENABLE, INTR_EN_PAGE_MASK); + + /* Load valid ecc byte to syndrome fragment register */ + elm_load_syndrome(info, err_vec, ecc_calc); + + /* Enable syndrome processing for which syndrome fragment is updated */ + elm_start_processing(info, err_vec); + + /* Wait for ELM module to finish locating error correction */ + wait_for_completion(&info->elm_completion); + + /* Disable page mode interrupt */ + reg_val = elm_read_reg(info, ELM_IRQENABLE); + elm_write_reg(info, ELM_IRQENABLE, reg_val & ~INTR_EN_PAGE_MASK); + elm_error_correction(info, err_vec); +} +EXPORT_SYMBOL(elm_decode_bch_error_page); + +static irqreturn_t elm_isr(int this_irq, void *dev_id) +{ + u32 reg_val; + struct elm_info *info = dev_id; + + reg_val = elm_read_reg(info, ELM_IRQSTATUS); + + /* All error vectors processed */ + if (reg_val & INTR_STATUS_PAGE_VALID) { + elm_write_reg(info, ELM_IRQSTATUS, + reg_val & INTR_STATUS_PAGE_VALID); + complete(&info->elm_completion); + return IRQ_HANDLED; + } + + return IRQ_NONE; +} + +static int elm_probe(struct platform_device *pdev) +{ + int ret = 0; + struct resource *res, *irq; + struct elm_info *info; + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->dev = &pdev->dev; + + irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!irq) { + dev_err(&pdev->dev, "no irq resource defined\n"); + return -ENODEV; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + info->elm_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(info->elm_base)) + return PTR_ERR(info->elm_base); + + ret = devm_request_irq(&pdev->dev, irq->start, elm_isr, 0, + pdev->name, info); + if (ret) { + dev_err(&pdev->dev, "failure requesting irq %i\n", irq->start); + return ret; + } + + pm_runtime_enable(&pdev->dev); + if (pm_runtime_get_sync(&pdev->dev) < 0) { + ret = -EINVAL; + pm_runtime_disable(&pdev->dev); + dev_err(&pdev->dev, "can't enable clock\n"); + return ret; + } + + init_completion(&info->elm_completion); + INIT_LIST_HEAD(&info->list); + list_add(&info->list, &elm_devices); + platform_set_drvdata(pdev, info); + return ret; +} + +static int elm_remove(struct platform_device *pdev) +{ + pm_runtime_put_sync(&pdev->dev); + pm_runtime_disable(&pdev->dev); + return 0; +} + +#ifdef CONFIG_PM_SLEEP +/** + * elm_context_save + * saves ELM configurations to preserve them across Hardware powered-down + */ +static int elm_context_save(struct elm_info *info) +{ + struct elm_registers *regs = &info->elm_regs; + enum bch_ecc bch_type = info->bch_type; + u32 offset = 0, i; + + regs->elm_irqenable = elm_read_reg(info, ELM_IRQENABLE); + regs->elm_sysconfig = elm_read_reg(info, ELM_SYSCONFIG); + regs->elm_location_config = elm_read_reg(info, ELM_LOCATION_CONFIG); + regs->elm_page_ctrl = elm_read_reg(info, ELM_PAGE_CTRL); + for (i = 0; i < ERROR_VECTOR_MAX; i++) { + offset = i * SYNDROME_FRAGMENT_REG_SIZE; + switch (bch_type) { + case BCH16_ECC: + regs->elm_syndrome_fragment_6[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_6 + offset); + regs->elm_syndrome_fragment_5[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_5 + offset); + regs->elm_syndrome_fragment_4[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_4 + offset); + case BCH8_ECC: + regs->elm_syndrome_fragment_3[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_3 + offset); + regs->elm_syndrome_fragment_2[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_2 + offset); + case BCH4_ECC: + regs->elm_syndrome_fragment_1[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_1 + offset); + regs->elm_syndrome_fragment_0[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_0 + offset); + break; + default: + return -EINVAL; + } + /* ELM SYNDROME_VALID bit in SYNDROME_FRAGMENT_6[] needs + * to be saved for all BCH schemes*/ + regs->elm_syndrome_fragment_6[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_6 + offset); + } + return 0; +} + +/** + * elm_context_restore + * writes configurations saved duing power-down back into ELM registers + */ +static int elm_context_restore(struct elm_info *info) +{ + struct elm_registers *regs = &info->elm_regs; + enum bch_ecc bch_type = info->bch_type; + u32 offset = 0, i; + + elm_write_reg(info, ELM_IRQENABLE, regs->elm_irqenable); + elm_write_reg(info, ELM_SYSCONFIG, regs->elm_sysconfig); + elm_write_reg(info, ELM_LOCATION_CONFIG, regs->elm_location_config); + elm_write_reg(info, ELM_PAGE_CTRL, regs->elm_page_ctrl); + for (i = 0; i < ERROR_VECTOR_MAX; i++) { + offset = i * SYNDROME_FRAGMENT_REG_SIZE; + switch (bch_type) { + case BCH16_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_6 + offset, + regs->elm_syndrome_fragment_6[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_5 + offset, + regs->elm_syndrome_fragment_5[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset, + regs->elm_syndrome_fragment_4[i]); + case BCH8_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_3 + offset, + regs->elm_syndrome_fragment_3[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_2 + offset, + regs->elm_syndrome_fragment_2[i]); + case BCH4_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_1 + offset, + regs->elm_syndrome_fragment_1[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_0 + offset, + regs->elm_syndrome_fragment_0[i]); + break; + default: + return -EINVAL; + } + /* ELM_SYNDROME_VALID bit to be set in last to trigger FSM */ + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_6 + offset, + regs->elm_syndrome_fragment_6[i] & + ELM_SYNDROME_VALID); + } + return 0; +} + +static int elm_suspend(struct device *dev) +{ + struct elm_info *info = dev_get_drvdata(dev); + elm_context_save(info); + pm_runtime_put_sync(dev); + return 0; +} + +static int elm_resume(struct device *dev) +{ + struct elm_info *info = dev_get_drvdata(dev); + pm_runtime_get_sync(dev); + elm_context_restore(info); + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(elm_pm_ops, elm_suspend, elm_resume); + +#ifdef CONFIG_OF +static const struct of_device_id elm_of_match[] = { + { .compatible = "ti,am3352-elm" }, + {}, +}; +MODULE_DEVICE_TABLE(of, elm_of_match); +#endif + +static struct platform_driver elm_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(elm_of_match), + .pm = &elm_pm_ops, + }, + .probe = elm_probe, + .remove = elm_remove, +}; + +module_platform_driver(elm_driver); + +MODULE_DESCRIPTION("ELM driver for BCH error correction"); +MODULE_AUTHOR("Texas Instruments"); +MODULE_ALIAS("platform: elm"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c new file mode 100644 index 000000000..c3c6d305c --- /dev/null +++ b/drivers/mtd/nand/orion_nand.c @@ -0,0 +1,219 @@ +/* + * drivers/mtd/nand/orion_nand.c + * + * NAND support for Marvell Orion SoC platforms + * + * Tzachi Perelstein <tzachi@marvell.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <asm/sizes.h> +#include <linux/platform_data/mtd-orion_nand.h> + +static void orion_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *nc = mtd->priv; + struct orion_nand_data *board = nc->priv; + u32 offs; + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + offs = (1 << board->cle); + else if (ctrl & NAND_ALE) + offs = (1 << board->ale); + else + return; + + if (nc->options & NAND_BUSWIDTH_16) + offs <<= 1; + + writeb(cmd, nc->IO_ADDR_W + offs); +} + +static void orion_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + void __iomem *io_base = chip->IO_ADDR_R; + uint64_t *buf64; + int i = 0; + + while (len && (unsigned long)buf & 7) { + *buf++ = readb(io_base); + len--; + } + buf64 = (uint64_t *)buf; + while (i < len/8) { + /* + * Since GCC has no proper constraint (PR 43518) + * force x variable to r2/r3 registers as ldrd instruction + * requires first register to be even. + */ + register uint64_t x asm ("r2"); + + asm volatile ("ldrd\t%0, [%1]" : "=&r" (x) : "r" (io_base)); + buf64[i++] = x; + } + i *= 8; + while (i < len) + buf[i++] = readb(io_base); +} + +static int __init orion_nand_probe(struct platform_device *pdev) +{ + struct mtd_info *mtd; + struct mtd_part_parser_data ppdata = {}; + struct nand_chip *nc; + struct orion_nand_data *board; + struct resource *res; + struct clk *clk; + void __iomem *io_base; + int ret = 0; + u32 val = 0; + + nc = devm_kzalloc(&pdev->dev, + sizeof(struct nand_chip) + sizeof(struct mtd_info), + GFP_KERNEL); + if (!nc) + return -ENOMEM; + mtd = (struct mtd_info *)(nc + 1); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + io_base = devm_ioremap_resource(&pdev->dev, res); + + if (IS_ERR(io_base)) + return PTR_ERR(io_base); + + if (pdev->dev.of_node) { + board = devm_kzalloc(&pdev->dev, sizeof(struct orion_nand_data), + GFP_KERNEL); + if (!board) + return -ENOMEM; + if (!of_property_read_u32(pdev->dev.of_node, "cle", &val)) + board->cle = (u8)val; + else + board->cle = 0; + if (!of_property_read_u32(pdev->dev.of_node, "ale", &val)) + board->ale = (u8)val; + else + board->ale = 1; + if (!of_property_read_u32(pdev->dev.of_node, + "bank-width", &val)) + board->width = (u8)val * 8; + else + board->width = 8; + if (!of_property_read_u32(pdev->dev.of_node, + "chip-delay", &val)) + board->chip_delay = (u8)val; + } else { + board = dev_get_platdata(&pdev->dev); + } + + mtd->priv = nc; + mtd->owner = THIS_MODULE; + + nc->priv = board; + nc->IO_ADDR_R = nc->IO_ADDR_W = io_base; + nc->cmd_ctrl = orion_nand_cmd_ctrl; + nc->read_buf = orion_nand_read_buf; + nc->ecc.mode = NAND_ECC_SOFT; + + if (board->chip_delay) + nc->chip_delay = board->chip_delay; + + WARN(board->width > 16, + "%d bit bus width out of range", + board->width); + + if (board->width == 16) + nc->options |= NAND_BUSWIDTH_16; + + if (board->dev_ready) + nc->dev_ready = board->dev_ready; + + platform_set_drvdata(pdev, mtd); + + /* Not all platforms can gate the clock, so it is not + an error if the clock does not exists. */ + clk = clk_get(&pdev->dev, NULL); + if (!IS_ERR(clk)) { + clk_prepare_enable(clk); + clk_put(clk); + } + + if (nand_scan(mtd, 1)) { + ret = -ENXIO; + goto no_dev; + } + + mtd->name = "orion_nand"; + ppdata.of_node = pdev->dev.of_node; + ret = mtd_device_parse_register(mtd, NULL, &ppdata, + board->parts, board->nr_parts); + if (ret) { + nand_release(mtd); + goto no_dev; + } + + return 0; + +no_dev: + if (!IS_ERR(clk)) { + clk_disable_unprepare(clk); + clk_put(clk); + } + + return ret; +} + +static int orion_nand_remove(struct platform_device *pdev) +{ + struct mtd_info *mtd = platform_get_drvdata(pdev); + struct clk *clk; + + nand_release(mtd); + + clk = clk_get(&pdev->dev, NULL); + if (!IS_ERR(clk)) { + clk_disable_unprepare(clk); + clk_put(clk); + } + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id orion_nand_of_match_table[] = { + { .compatible = "marvell,orion-nand", }, + {}, +}; +#endif + +static struct platform_driver orion_nand_driver = { + .remove = orion_nand_remove, + .driver = { + .name = "orion_nand", + .of_match_table = of_match_ptr(orion_nand_of_match_table), + }, +}; + +module_platform_driver_probe(orion_nand_driver, orion_nand_probe); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Tzachi Perelstein"); +MODULE_DESCRIPTION("NAND glue for Orion platforms"); +MODULE_ALIAS("platform:orion_nand"); diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/pasemi_nand.c new file mode 100644 index 000000000..66c345b42 --- /dev/null +++ b/drivers/mtd/nand/pasemi_nand.c @@ -0,0 +1,236 @@ +/* + * Copyright (C) 2006-2007 PA Semi, Inc + * + * Author: Egor Martovetsky <egor@pasemi.com> + * Maintained by: Olof Johansson <olof@lixom.net> + * + * Driver for the PWRficient onchip NAND flash interface + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#undef DEBUG + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/pci.h> + +#include <asm/io.h> + +#define LBICTRL_LPCCTL_NR 0x00004000 +#define CLE_PIN_CTL 15 +#define ALE_PIN_CTL 14 + +static unsigned int lpcctl; +static struct mtd_info *pasemi_nand_mtd; +static const char driver_name[] = "pasemi-nand"; + +static void pasemi_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + while (len > 0x800) { + memcpy_fromio(buf, chip->IO_ADDR_R, 0x800); + buf += 0x800; + len -= 0x800; + } + memcpy_fromio(buf, chip->IO_ADDR_R, len); +} + +static void pasemi_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct nand_chip *chip = mtd->priv; + + while (len > 0x800) { + memcpy_toio(chip->IO_ADDR_R, buf, 0x800); + buf += 0x800; + len -= 0x800; + } + memcpy_toio(chip->IO_ADDR_R, buf, len); +} + +static void pasemi_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + out_8(chip->IO_ADDR_W + (1 << CLE_PIN_CTL), cmd); + else + out_8(chip->IO_ADDR_W + (1 << ALE_PIN_CTL), cmd); + + /* Push out posted writes */ + eieio(); + inl(lpcctl); +} + +int pasemi_device_ready(struct mtd_info *mtd) +{ + return !!(inl(lpcctl) & LBICTRL_LPCCTL_NR); +} + +static int pasemi_nand_probe(struct platform_device *ofdev) +{ + struct pci_dev *pdev; + struct device_node *np = ofdev->dev.of_node; + struct resource res; + struct nand_chip *chip; + int err = 0; + + err = of_address_to_resource(np, 0, &res); + + if (err) + return -EINVAL; + + /* We only support one device at the moment */ + if (pasemi_nand_mtd) + return -ENODEV; + + pr_debug("pasemi_nand at %pR\n", &res); + + /* Allocate memory for MTD device structure and private data */ + pasemi_nand_mtd = kzalloc(sizeof(struct mtd_info) + + sizeof(struct nand_chip), GFP_KERNEL); + if (!pasemi_nand_mtd) { + printk(KERN_WARNING + "Unable to allocate PASEMI NAND MTD device structure\n"); + err = -ENOMEM; + goto out; + } + + /* Get pointer to private data */ + chip = (struct nand_chip *)&pasemi_nand_mtd[1]; + + /* Link the private data with the MTD structure */ + pasemi_nand_mtd->priv = chip; + pasemi_nand_mtd->owner = THIS_MODULE; + + chip->IO_ADDR_R = of_iomap(np, 0); + chip->IO_ADDR_W = chip->IO_ADDR_R; + + if (!chip->IO_ADDR_R) { + err = -EIO; + goto out_mtd; + } + + pdev = pci_get_device(PCI_VENDOR_ID_PASEMI, 0xa008, NULL); + if (!pdev) { + err = -ENODEV; + goto out_ior; + } + + lpcctl = pci_resource_start(pdev, 0); + pci_dev_put(pdev); + + if (!request_region(lpcctl, 4, driver_name)) { + err = -EBUSY; + goto out_ior; + } + + chip->cmd_ctrl = pasemi_hwcontrol; + chip->dev_ready = pasemi_device_ready; + chip->read_buf = pasemi_read_buf; + chip->write_buf = pasemi_write_buf; + chip->chip_delay = 0; + chip->ecc.mode = NAND_ECC_SOFT; + + /* Enable the following for a flash based bad block table */ + chip->bbt_options = NAND_BBT_USE_FLASH; + + /* Scan to find existence of the device */ + if (nand_scan(pasemi_nand_mtd, 1)) { + err = -ENXIO; + goto out_lpc; + } + + if (mtd_device_register(pasemi_nand_mtd, NULL, 0)) { + printk(KERN_ERR "pasemi_nand: Unable to register MTD device\n"); + err = -ENODEV; + goto out_lpc; + } + + printk(KERN_INFO "PA Semi NAND flash at %08llx, control at I/O %x\n", + res.start, lpcctl); + + return 0; + + out_lpc: + release_region(lpcctl, 4); + out_ior: + iounmap(chip->IO_ADDR_R); + out_mtd: + kfree(pasemi_nand_mtd); + out: + return err; +} + +static int pasemi_nand_remove(struct platform_device *ofdev) +{ + struct nand_chip *chip; + + if (!pasemi_nand_mtd) + return 0; + + chip = pasemi_nand_mtd->priv; + + /* Release resources, unregister device */ + nand_release(pasemi_nand_mtd); + + release_region(lpcctl, 4); + + iounmap(chip->IO_ADDR_R); + + /* Free the MTD device structure */ + kfree(pasemi_nand_mtd); + + pasemi_nand_mtd = NULL; + + return 0; +} + +static const struct of_device_id pasemi_nand_match[] = +{ + { + .compatible = "pasemi,localbus-nand", + }, + {}, +}; + +MODULE_DEVICE_TABLE(of, pasemi_nand_match); + +static struct platform_driver pasemi_nand_driver = +{ + .driver = { + .name = driver_name, + .of_match_table = pasemi_nand_match, + }, + .probe = pasemi_nand_probe, + .remove = pasemi_nand_remove, +}; + +module_platform_driver(pasemi_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Egor Martovetsky <egor@pasemi.com>"); +MODULE_DESCRIPTION("NAND flash interface driver for PA Semi PWRficient"); diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/plat_nand.c new file mode 100644 index 000000000..4535c263f --- /dev/null +++ b/drivers/mtd/nand/plat_nand.c @@ -0,0 +1,150 @@ +/* + * Generic NAND driver + * + * Author: Vitaly Wool <vitalywool@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/err.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> + +struct plat_nand_data { + struct nand_chip chip; + struct mtd_info mtd; + void __iomem *io_base; +}; + +static const char *part_probe_types[] = { "cmdlinepart", NULL }; + +/* + * Probe for the NAND device. + */ +static int plat_nand_probe(struct platform_device *pdev) +{ + struct platform_nand_data *pdata = dev_get_platdata(&pdev->dev); + struct mtd_part_parser_data ppdata; + struct plat_nand_data *data; + struct resource *res; + const char **part_types; + int err = 0; + + if (!pdata) { + dev_err(&pdev->dev, "platform_nand_data is missing\n"); + return -EINVAL; + } + + if (pdata->chip.nr_chips < 1) { + dev_err(&pdev->dev, "invalid number of chips specified\n"); + return -EINVAL; + } + + /* Allocate memory for the device structure (and zero it) */ + data = devm_kzalloc(&pdev->dev, sizeof(struct plat_nand_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + data->io_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(data->io_base)) + return PTR_ERR(data->io_base); + + data->chip.priv = &data; + data->mtd.priv = &data->chip; + data->mtd.owner = THIS_MODULE; + data->mtd.name = dev_name(&pdev->dev); + + data->chip.IO_ADDR_R = data->io_base; + data->chip.IO_ADDR_W = data->io_base; + data->chip.cmd_ctrl = pdata->ctrl.cmd_ctrl; + data->chip.dev_ready = pdata->ctrl.dev_ready; + data->chip.select_chip = pdata->ctrl.select_chip; + data->chip.write_buf = pdata->ctrl.write_buf; + data->chip.read_buf = pdata->ctrl.read_buf; + data->chip.read_byte = pdata->ctrl.read_byte; + data->chip.chip_delay = pdata->chip.chip_delay; + data->chip.options |= pdata->chip.options; + data->chip.bbt_options |= pdata->chip.bbt_options; + + data->chip.ecc.hwctl = pdata->ctrl.hwcontrol; + data->chip.ecc.layout = pdata->chip.ecclayout; + data->chip.ecc.mode = NAND_ECC_SOFT; + + platform_set_drvdata(pdev, data); + + /* Handle any platform specific setup */ + if (pdata->ctrl.probe) { + err = pdata->ctrl.probe(pdev); + if (err) + goto out; + } + + /* Scan to find existence of the device */ + if (nand_scan(&data->mtd, pdata->chip.nr_chips)) { + err = -ENXIO; + goto out; + } + + part_types = pdata->chip.part_probe_types ? : part_probe_types; + + ppdata.of_node = pdev->dev.of_node; + err = mtd_device_parse_register(&data->mtd, part_types, &ppdata, + pdata->chip.partitions, + pdata->chip.nr_partitions); + + if (!err) + return err; + + nand_release(&data->mtd); +out: + if (pdata->ctrl.remove) + pdata->ctrl.remove(pdev); + return err; +} + +/* + * Remove a NAND device. + */ +static int plat_nand_remove(struct platform_device *pdev) +{ + struct plat_nand_data *data = platform_get_drvdata(pdev); + struct platform_nand_data *pdata = dev_get_platdata(&pdev->dev); + + nand_release(&data->mtd); + if (pdata->ctrl.remove) + pdata->ctrl.remove(pdev); + + return 0; +} + +static const struct of_device_id plat_nand_match[] = { + { .compatible = "gen_nand" }, + {}, +}; +MODULE_DEVICE_TABLE(of, plat_nand_match); + +static struct platform_driver plat_nand_driver = { + .probe = plat_nand_probe, + .remove = plat_nand_remove, + .driver = { + .name = "gen_nand", + .of_match_table = plat_nand_match, + }, +}; + +module_platform_driver(plat_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Vitaly Wool"); +MODULE_DESCRIPTION("Simple generic NAND driver"); +MODULE_ALIAS("platform:gen_nand"); diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c new file mode 100644 index 000000000..a4615fcc3 --- /dev/null +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -0,0 +1,1940 @@ +/* + * drivers/mtd/nand/pxa3xx_nand.c + * + * Copyright © 2005 Intel Corporation + * Copyright © 2006 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * See Documentation/mtd/nand/pxa3xx-nand.txt for more details. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_mtd.h> + +#if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP) +#define ARCH_HAS_DMA +#endif + +#ifdef ARCH_HAS_DMA +#include <mach/dma.h> +#endif + +#include <linux/platform_data/mtd-nand-pxa3xx.h> + +#define CHIP_DELAY_TIMEOUT msecs_to_jiffies(200) +#define NAND_STOP_DELAY msecs_to_jiffies(40) +#define PAGE_CHUNK_SIZE (2048) + +/* + * Define a buffer size for the initial command that detects the flash device: + * STATUS, READID and PARAM. The largest of these is the PARAM command, + * needing 256 bytes. + */ +#define INIT_BUFFER_SIZE 256 + +/* registers and bit definitions */ +#define NDCR (0x00) /* Control register */ +#define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */ +#define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */ +#define NDSR (0x14) /* Status Register */ +#define NDPCR (0x18) /* Page Count Register */ +#define NDBDR0 (0x1C) /* Bad Block Register 0 */ +#define NDBDR1 (0x20) /* Bad Block Register 1 */ +#define NDECCCTRL (0x28) /* ECC control */ +#define NDDB (0x40) /* Data Buffer */ +#define NDCB0 (0x48) /* Command Buffer0 */ +#define NDCB1 (0x4C) /* Command Buffer1 */ +#define NDCB2 (0x50) /* Command Buffer2 */ + +#define NDCR_SPARE_EN (0x1 << 31) +#define NDCR_ECC_EN (0x1 << 30) +#define NDCR_DMA_EN (0x1 << 29) +#define NDCR_ND_RUN (0x1 << 28) +#define NDCR_DWIDTH_C (0x1 << 27) +#define NDCR_DWIDTH_M (0x1 << 26) +#define NDCR_PAGE_SZ (0x1 << 24) +#define NDCR_NCSX (0x1 << 23) +#define NDCR_ND_MODE (0x3 << 21) +#define NDCR_NAND_MODE (0x0) +#define NDCR_CLR_PG_CNT (0x1 << 20) +#define NDCR_STOP_ON_UNCOR (0x1 << 19) +#define NDCR_RD_ID_CNT_MASK (0x7 << 16) +#define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK) + +#define NDCR_RA_START (0x1 << 15) +#define NDCR_PG_PER_BLK (0x1 << 14) +#define NDCR_ND_ARB_EN (0x1 << 12) +#define NDCR_INT_MASK (0xFFF) + +#define NDSR_MASK (0xfff) +#define NDSR_ERR_CNT_OFF (16) +#define NDSR_ERR_CNT_MASK (0x1f) +#define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK) +#define NDSR_RDY (0x1 << 12) +#define NDSR_FLASH_RDY (0x1 << 11) +#define NDSR_CS0_PAGED (0x1 << 10) +#define NDSR_CS1_PAGED (0x1 << 9) +#define NDSR_CS0_CMDD (0x1 << 8) +#define NDSR_CS1_CMDD (0x1 << 7) +#define NDSR_CS0_BBD (0x1 << 6) +#define NDSR_CS1_BBD (0x1 << 5) +#define NDSR_UNCORERR (0x1 << 4) +#define NDSR_CORERR (0x1 << 3) +#define NDSR_WRDREQ (0x1 << 2) +#define NDSR_RDDREQ (0x1 << 1) +#define NDSR_WRCMDREQ (0x1) + +#define NDCB0_LEN_OVRD (0x1 << 28) +#define NDCB0_ST_ROW_EN (0x1 << 26) +#define NDCB0_AUTO_RS (0x1 << 25) +#define NDCB0_CSEL (0x1 << 24) +#define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29) +#define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK) +#define NDCB0_CMD_TYPE_MASK (0x7 << 21) +#define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK) +#define NDCB0_NC (0x1 << 20) +#define NDCB0_DBC (0x1 << 19) +#define NDCB0_ADDR_CYC_MASK (0x7 << 16) +#define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK) +#define NDCB0_CMD2_MASK (0xff << 8) +#define NDCB0_CMD1_MASK (0xff) +#define NDCB0_ADDR_CYC_SHIFT (16) + +#define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */ +#define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */ +#define EXT_CMD_TYPE_READ 4 /* Read */ +#define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */ +#define EXT_CMD_TYPE_FINAL 3 /* Final command */ +#define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */ +#define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */ + +/* macros for registers read/write */ +#define nand_writel(info, off, val) \ + writel_relaxed((val), (info)->mmio_base + (off)) + +#define nand_readl(info, off) \ + readl_relaxed((info)->mmio_base + (off)) + +/* error code and state */ +enum { + ERR_NONE = 0, + ERR_DMABUSERR = -1, + ERR_SENDCMD = -2, + ERR_UNCORERR = -3, + ERR_BBERR = -4, + ERR_CORERR = -5, +}; + +enum { + STATE_IDLE = 0, + STATE_PREPARED, + STATE_CMD_HANDLE, + STATE_DMA_READING, + STATE_DMA_WRITING, + STATE_DMA_DONE, + STATE_PIO_READING, + STATE_PIO_WRITING, + STATE_CMD_DONE, + STATE_READY, +}; + +enum pxa3xx_nand_variant { + PXA3XX_NAND_VARIANT_PXA, + PXA3XX_NAND_VARIANT_ARMADA370, +}; + +struct pxa3xx_nand_host { + struct nand_chip chip; + struct mtd_info *mtd; + void *info_data; + + /* page size of attached chip */ + int use_ecc; + int cs; + + /* calculated from pxa3xx_nand_flash data */ + unsigned int col_addr_cycles; + unsigned int row_addr_cycles; + size_t read_id_bytes; + +}; + +struct pxa3xx_nand_info { + struct nand_hw_control controller; + struct platform_device *pdev; + + struct clk *clk; + void __iomem *mmio_base; + unsigned long mmio_phys; + struct completion cmd_complete, dev_ready; + + unsigned int buf_start; + unsigned int buf_count; + unsigned int buf_size; + unsigned int data_buff_pos; + unsigned int oob_buff_pos; + + /* DMA information */ + int drcmr_dat; + int drcmr_cmd; + + unsigned char *data_buff; + unsigned char *oob_buff; + dma_addr_t data_buff_phys; + int data_dma_ch; + struct pxa_dma_desc *data_desc; + dma_addr_t data_desc_addr; + + struct pxa3xx_nand_host *host[NUM_CHIP_SELECT]; + unsigned int state; + + /* + * This driver supports NFCv1 (as found in PXA SoC) + * and NFCv2 (as found in Armada 370/XP SoC). + */ + enum pxa3xx_nand_variant variant; + + int cs; + int use_ecc; /* use HW ECC ? */ + int ecc_bch; /* using BCH ECC? */ + int use_dma; /* use DMA ? */ + int use_spare; /* use spare ? */ + int need_wait; + + unsigned int data_size; /* data to be read from FIFO */ + unsigned int chunk_size; /* split commands chunk size */ + unsigned int oob_size; + unsigned int spare_size; + unsigned int ecc_size; + unsigned int ecc_err_cnt; + unsigned int max_bitflips; + int retcode; + + /* cached register value */ + uint32_t reg_ndcr; + uint32_t ndtr0cs0; + uint32_t ndtr1cs0; + + /* generated NDCBx register values */ + uint32_t ndcb0; + uint32_t ndcb1; + uint32_t ndcb2; + uint32_t ndcb3; +}; + +static bool use_dma = 1; +module_param(use_dma, bool, 0444); +MODULE_PARM_DESC(use_dma, "enable DMA for data transferring to/from NAND HW"); + +static struct pxa3xx_nand_timing timing[] = { + { 40, 80, 60, 100, 80, 100, 90000, 400, 40, }, + { 10, 0, 20, 40, 30, 40, 11123, 110, 10, }, + { 10, 25, 15, 25, 15, 30, 25000, 60, 10, }, + { 10, 35, 15, 25, 15, 25, 25000, 60, 10, }, +}; + +static struct pxa3xx_nand_flash builtin_flash_types[] = { +{ "DEFAULT FLASH", 0, 0, 2048, 8, 8, 0, &timing[0] }, +{ "64MiB 16-bit", 0x46ec, 32, 512, 16, 16, 4096, &timing[1] }, +{ "256MiB 8-bit", 0xdaec, 64, 2048, 8, 8, 2048, &timing[1] }, +{ "4GiB 8-bit", 0xd7ec, 128, 4096, 8, 8, 8192, &timing[1] }, +{ "128MiB 8-bit", 0xa12c, 64, 2048, 8, 8, 1024, &timing[2] }, +{ "128MiB 16-bit", 0xb12c, 64, 2048, 16, 16, 1024, &timing[2] }, +{ "512MiB 8-bit", 0xdc2c, 64, 2048, 8, 8, 4096, &timing[2] }, +{ "512MiB 16-bit", 0xcc2c, 64, 2048, 16, 16, 4096, &timing[2] }, +{ "256MiB 16-bit", 0xba20, 64, 2048, 16, 16, 2048, &timing[3] }, +}; + +static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' }; +static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_mirror_pattern +}; + +static struct nand_ecclayout ecc_layout_2KB_bch4bit = { + .eccbytes = 32, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { {2, 30} } +}; + +static struct nand_ecclayout ecc_layout_4KB_bch4bit = { + .eccbytes = 64, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127}, + /* Bootrom looks in bytes 0 & 5 for bad blocks */ + .oobfree = { {6, 26}, { 64, 32} } +}; + +static struct nand_ecclayout ecc_layout_4KB_bch8bit = { + .eccbytes = 128, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { } +}; + +/* Define a default flash type setting serve as flash detecting only */ +#define DEFAULT_FLASH_TYPE (&builtin_flash_types[0]) + +#define NDTR0_tCH(c) (min((c), 7) << 19) +#define NDTR0_tCS(c) (min((c), 7) << 16) +#define NDTR0_tWH(c) (min((c), 7) << 11) +#define NDTR0_tWP(c) (min((c), 7) << 8) +#define NDTR0_tRH(c) (min((c), 7) << 3) +#define NDTR0_tRP(c) (min((c), 7) << 0) + +#define NDTR1_tR(c) (min((c), 65535) << 16) +#define NDTR1_tWHR(c) (min((c), 15) << 4) +#define NDTR1_tAR(c) (min((c), 15) << 0) + +/* convert nano-seconds to nand flash controller clock cycles */ +#define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000) + +static const struct of_device_id pxa3xx_nand_dt_ids[] = { + { + .compatible = "marvell,pxa3xx-nand", + .data = (void *)PXA3XX_NAND_VARIANT_PXA, + }, + { + .compatible = "marvell,armada370-nand", + .data = (void *)PXA3XX_NAND_VARIANT_ARMADA370, + }, + {} +}; +MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids); + +static enum pxa3xx_nand_variant +pxa3xx_nand_get_variant(struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); + if (!of_id) + return PXA3XX_NAND_VARIANT_PXA; + return (enum pxa3xx_nand_variant)of_id->data; +} + +static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host, + const struct pxa3xx_nand_timing *t) +{ + struct pxa3xx_nand_info *info = host->info_data; + unsigned long nand_clk = clk_get_rate(info->clk); + uint32_t ndtr0, ndtr1; + + ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) | + NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) | + NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) | + NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) | + NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) | + NDTR0_tRP(ns2cycle(t->tRP, nand_clk)); + + ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) | + NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) | + NDTR1_tAR(ns2cycle(t->tAR, nand_clk)); + + info->ndtr0cs0 = ndtr0; + info->ndtr1cs0 = ndtr1; + nand_writel(info, NDTR0CS0, ndtr0); + nand_writel(info, NDTR1CS0, ndtr1); +} + +/* + * Set the data and OOB size, depending on the selected + * spare and ECC configuration. + * Only applicable to READ0, READOOB and PAGEPROG commands. + */ +static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info, + struct mtd_info *mtd) +{ + int oob_enable = info->reg_ndcr & NDCR_SPARE_EN; + + info->data_size = mtd->writesize; + if (!oob_enable) + return; + + info->oob_size = info->spare_size; + if (!info->use_ecc) + info->oob_size += info->ecc_size; +} + +/** + * NOTE: it is a must to set ND_RUN firstly, then write + * command buffer, otherwise, it does not work. + * We enable all the interrupt at the same time, and + * let pxa3xx_nand_irq to handle all logic. + */ +static void pxa3xx_nand_start(struct pxa3xx_nand_info *info) +{ + uint32_t ndcr; + + ndcr = info->reg_ndcr; + + if (info->use_ecc) { + ndcr |= NDCR_ECC_EN; + if (info->ecc_bch) + nand_writel(info, NDECCCTRL, 0x1); + } else { + ndcr &= ~NDCR_ECC_EN; + if (info->ecc_bch) + nand_writel(info, NDECCCTRL, 0x0); + } + + if (info->use_dma) + ndcr |= NDCR_DMA_EN; + else + ndcr &= ~NDCR_DMA_EN; + + if (info->use_spare) + ndcr |= NDCR_SPARE_EN; + else + ndcr &= ~NDCR_SPARE_EN; + + ndcr |= NDCR_ND_RUN; + + /* clear status bits and run */ + nand_writel(info, NDCR, 0); + nand_writel(info, NDSR, NDSR_MASK); + nand_writel(info, NDCR, ndcr); +} + +static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info) +{ + uint32_t ndcr; + int timeout = NAND_STOP_DELAY; + + /* wait RUN bit in NDCR become 0 */ + ndcr = nand_readl(info, NDCR); + while ((ndcr & NDCR_ND_RUN) && (timeout-- > 0)) { + ndcr = nand_readl(info, NDCR); + udelay(1); + } + + if (timeout <= 0) { + ndcr &= ~NDCR_ND_RUN; + nand_writel(info, NDCR, ndcr); + } + /* clear status bits */ + nand_writel(info, NDSR, NDSR_MASK); +} + +static void __maybe_unused +enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) +{ + uint32_t ndcr; + + ndcr = nand_readl(info, NDCR); + nand_writel(info, NDCR, ndcr & ~int_mask); +} + +static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) +{ + uint32_t ndcr; + + ndcr = nand_readl(info, NDCR); + nand_writel(info, NDCR, ndcr | int_mask); +} + +static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len) +{ + if (info->ecc_bch) { + int timeout; + + /* + * According to the datasheet, when reading from NDDB + * with BCH enabled, after each 32 bytes reads, we + * have to make sure that the NDSR.RDDREQ bit is set. + * + * Drain the FIFO 8 32 bits reads at a time, and skip + * the polling on the last read. + */ + while (len > 8) { + __raw_readsl(info->mmio_base + NDDB, data, 8); + + for (timeout = 0; + !(nand_readl(info, NDSR) & NDSR_RDDREQ); + timeout++) { + if (timeout >= 5) { + dev_err(&info->pdev->dev, + "Timeout on RDDREQ while draining the FIFO\n"); + return; + } + + mdelay(1); + } + + data += 32; + len -= 8; + } + } + + __raw_readsl(info->mmio_base + NDDB, data, len); +} + +static void handle_data_pio(struct pxa3xx_nand_info *info) +{ + unsigned int do_bytes = min(info->data_size, info->chunk_size); + + switch (info->state) { + case STATE_PIO_WRITING: + __raw_writesl(info->mmio_base + NDDB, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(do_bytes, 4)); + + if (info->oob_size > 0) + __raw_writesl(info->mmio_base + NDDB, + info->oob_buff + info->oob_buff_pos, + DIV_ROUND_UP(info->oob_size, 4)); + break; + case STATE_PIO_READING: + drain_fifo(info, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(do_bytes, 4)); + + if (info->oob_size > 0) + drain_fifo(info, + info->oob_buff + info->oob_buff_pos, + DIV_ROUND_UP(info->oob_size, 4)); + break; + default: + dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, + info->state); + BUG(); + } + + /* Update buffer pointers for multi-page read/write */ + info->data_buff_pos += do_bytes; + info->oob_buff_pos += info->oob_size; + info->data_size -= do_bytes; +} + +#ifdef ARCH_HAS_DMA +static void start_data_dma(struct pxa3xx_nand_info *info) +{ + struct pxa_dma_desc *desc = info->data_desc; + int dma_len = ALIGN(info->data_size + info->oob_size, 32); + + desc->ddadr = DDADR_STOP; + desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len; + + switch (info->state) { + case STATE_DMA_WRITING: + desc->dsadr = info->data_buff_phys; + desc->dtadr = info->mmio_phys + NDDB; + desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG; + break; + case STATE_DMA_READING: + desc->dtadr = info->data_buff_phys; + desc->dsadr = info->mmio_phys + NDDB; + desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC; + break; + default: + dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, + info->state); + BUG(); + } + + DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch; + DDADR(info->data_dma_ch) = info->data_desc_addr; + DCSR(info->data_dma_ch) |= DCSR_RUN; +} + +static void pxa3xx_nand_data_dma_irq(int channel, void *data) +{ + struct pxa3xx_nand_info *info = data; + uint32_t dcsr; + + dcsr = DCSR(channel); + DCSR(channel) = dcsr; + + if (dcsr & DCSR_BUSERR) { + info->retcode = ERR_DMABUSERR; + } + + info->state = STATE_DMA_DONE; + enable_int(info, NDCR_INT_MASK); + nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ); +} +#else +static void start_data_dma(struct pxa3xx_nand_info *info) +{} +#endif + +static irqreturn_t pxa3xx_nand_irq_thread(int irq, void *data) +{ + struct pxa3xx_nand_info *info = data; + + handle_data_pio(info); + + info->state = STATE_CMD_DONE; + nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ); + + return IRQ_HANDLED; +} + +static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) +{ + struct pxa3xx_nand_info *info = devid; + unsigned int status, is_completed = 0, is_ready = 0; + unsigned int ready, cmd_done; + irqreturn_t ret = IRQ_HANDLED; + + if (info->cs == 0) { + ready = NDSR_FLASH_RDY; + cmd_done = NDSR_CS0_CMDD; + } else { + ready = NDSR_RDY; + cmd_done = NDSR_CS1_CMDD; + } + + status = nand_readl(info, NDSR); + + if (status & NDSR_UNCORERR) + info->retcode = ERR_UNCORERR; + if (status & NDSR_CORERR) { + info->retcode = ERR_CORERR; + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 && + info->ecc_bch) + info->ecc_err_cnt = NDSR_ERR_CNT(status); + else + info->ecc_err_cnt = 1; + + /* + * Each chunk composing a page is corrected independently, + * and we need to store maximum number of corrected bitflips + * to return it to the MTD layer in ecc.read_page(). + */ + info->max_bitflips = max_t(unsigned int, + info->max_bitflips, + info->ecc_err_cnt); + } + if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) { + /* whether use dma to transfer data */ + if (info->use_dma) { + disable_int(info, NDCR_INT_MASK); + info->state = (status & NDSR_RDDREQ) ? + STATE_DMA_READING : STATE_DMA_WRITING; + start_data_dma(info); + goto NORMAL_IRQ_EXIT; + } else { + info->state = (status & NDSR_RDDREQ) ? + STATE_PIO_READING : STATE_PIO_WRITING; + ret = IRQ_WAKE_THREAD; + goto NORMAL_IRQ_EXIT; + } + } + if (status & cmd_done) { + info->state = STATE_CMD_DONE; + is_completed = 1; + } + if (status & ready) { + info->state = STATE_READY; + is_ready = 1; + } + + if (status & NDSR_WRCMDREQ) { + nand_writel(info, NDSR, NDSR_WRCMDREQ); + status &= ~NDSR_WRCMDREQ; + info->state = STATE_CMD_HANDLE; + + /* + * Command buffer registers NDCB{0-2} (and optionally NDCB3) + * must be loaded by writing directly either 12 or 16 + * bytes directly to NDCB0, four bytes at a time. + * + * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored + * but each NDCBx register can be read. + */ + nand_writel(info, NDCB0, info->ndcb0); + nand_writel(info, NDCB0, info->ndcb1); + nand_writel(info, NDCB0, info->ndcb2); + + /* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */ + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) + nand_writel(info, NDCB0, info->ndcb3); + } + + /* clear NDSR to let the controller exit the IRQ */ + nand_writel(info, NDSR, status); + if (is_completed) + complete(&info->cmd_complete); + if (is_ready) + complete(&info->dev_ready); +NORMAL_IRQ_EXIT: + return ret; +} + +static inline int is_buf_blank(uint8_t *buf, size_t len) +{ + for (; len > 0; len--) + if (*buf++ != 0xff) + return 0; + return 1; +} + +static void set_command_address(struct pxa3xx_nand_info *info, + unsigned int page_size, uint16_t column, int page_addr) +{ + /* small page addr setting */ + if (page_size < PAGE_CHUNK_SIZE) { + info->ndcb1 = ((page_addr & 0xFFFFFF) << 8) + | (column & 0xFF); + + info->ndcb2 = 0; + } else { + info->ndcb1 = ((page_addr & 0xFFFF) << 16) + | (column & 0xFFFF); + + if (page_addr & 0xFF0000) + info->ndcb2 = (page_addr & 0xFF0000) >> 16; + else + info->ndcb2 = 0; + } +} + +static void prepare_start_command(struct pxa3xx_nand_info *info, int command) +{ + struct pxa3xx_nand_host *host = info->host[info->cs]; + struct mtd_info *mtd = host->mtd; + + /* reset data and oob column point to handle data */ + info->buf_start = 0; + info->buf_count = 0; + info->oob_size = 0; + info->data_buff_pos = 0; + info->oob_buff_pos = 0; + info->use_ecc = 0; + info->use_spare = 1; + info->retcode = ERR_NONE; + info->ecc_err_cnt = 0; + info->ndcb3 = 0; + info->need_wait = 0; + + switch (command) { + case NAND_CMD_READ0: + case NAND_CMD_PAGEPROG: + info->use_ecc = 1; + case NAND_CMD_READOOB: + pxa3xx_set_datasize(info, mtd); + break; + case NAND_CMD_PARAM: + info->use_spare = 0; + break; + default: + info->ndcb1 = 0; + info->ndcb2 = 0; + break; + } + + /* + * If we are about to issue a read command, or about to set + * the write address, then clean the data buffer. + */ + if (command == NAND_CMD_READ0 || + command == NAND_CMD_READOOB || + command == NAND_CMD_SEQIN) { + + info->buf_count = mtd->writesize + mtd->oobsize; + memset(info->data_buff, 0xFF, info->buf_count); + } + +} + +static int prepare_set_command(struct pxa3xx_nand_info *info, int command, + int ext_cmd_type, uint16_t column, int page_addr) +{ + int addr_cycle, exec_cmd; + struct pxa3xx_nand_host *host; + struct mtd_info *mtd; + + host = info->host[info->cs]; + mtd = host->mtd; + addr_cycle = 0; + exec_cmd = 1; + + if (info->cs != 0) + info->ndcb0 = NDCB0_CSEL; + else + info->ndcb0 = 0; + + if (command == NAND_CMD_SEQIN) + exec_cmd = 0; + + addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles + + host->col_addr_cycles); + + switch (command) { + case NAND_CMD_READOOB: + case NAND_CMD_READ0: + info->buf_start = column; + info->ndcb0 |= NDCB0_CMD_TYPE(0) + | addr_cycle + | NAND_CMD_READ0; + + if (command == NAND_CMD_READOOB) + info->buf_start += mtd->writesize; + + /* + * Multiple page read needs an 'extended command type' field, + * which is either naked-read or last-read according to the + * state. + */ + if (mtd->writesize == PAGE_CHUNK_SIZE) { + info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8); + } else if (mtd->writesize > PAGE_CHUNK_SIZE) { + info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8) + | NDCB0_LEN_OVRD + | NDCB0_EXT_CMD_TYPE(ext_cmd_type); + info->ndcb3 = info->chunk_size + + info->oob_size; + } + + set_command_address(info, mtd->writesize, column, page_addr); + break; + + case NAND_CMD_SEQIN: + + info->buf_start = column; + set_command_address(info, mtd->writesize, 0, page_addr); + + /* + * Multiple page programming needs to execute the initial + * SEQIN command that sets the page address. + */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_EXT_CMD_TYPE(ext_cmd_type) + | addr_cycle + | command; + /* No data transfer in this case */ + info->data_size = 0; + exec_cmd = 1; + } + break; + + case NAND_CMD_PAGEPROG: + if (is_buf_blank(info->data_buff, + (mtd->writesize + mtd->oobsize))) { + exec_cmd = 0; + break; + } + + /* Second command setting for large pages */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + /* + * Multiple page write uses the 'extended command' + * field. This can be used to issue a command dispatch + * or a naked-write depending on the current stage. + */ + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_LEN_OVRD + | NDCB0_EXT_CMD_TYPE(ext_cmd_type); + info->ndcb3 = info->chunk_size + + info->oob_size; + + /* + * This is the command dispatch that completes a chunked + * page program operation. + */ + if (info->data_size == 0) { + info->ndcb0 = NDCB0_CMD_TYPE(0x1) + | NDCB0_EXT_CMD_TYPE(ext_cmd_type) + | command; + info->ndcb1 = 0; + info->ndcb2 = 0; + info->ndcb3 = 0; + } + } else { + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_AUTO_RS + | NDCB0_ST_ROW_EN + | NDCB0_DBC + | (NAND_CMD_PAGEPROG << 8) + | NAND_CMD_SEQIN + | addr_cycle; + } + break; + + case NAND_CMD_PARAM: + info->buf_count = 256; + info->ndcb0 |= NDCB0_CMD_TYPE(0) + | NDCB0_ADDR_CYC(1) + | NDCB0_LEN_OVRD + | command; + info->ndcb1 = (column & 0xFF); + info->ndcb3 = 256; + info->data_size = 256; + break; + + case NAND_CMD_READID: + info->buf_count = host->read_id_bytes; + info->ndcb0 |= NDCB0_CMD_TYPE(3) + | NDCB0_ADDR_CYC(1) + | command; + info->ndcb1 = (column & 0xFF); + + info->data_size = 8; + break; + case NAND_CMD_STATUS: + info->buf_count = 1; + info->ndcb0 |= NDCB0_CMD_TYPE(4) + | NDCB0_ADDR_CYC(1) + | command; + + info->data_size = 8; + break; + + case NAND_CMD_ERASE1: + info->ndcb0 |= NDCB0_CMD_TYPE(2) + | NDCB0_AUTO_RS + | NDCB0_ADDR_CYC(3) + | NDCB0_DBC + | (NAND_CMD_ERASE2 << 8) + | NAND_CMD_ERASE1; + info->ndcb1 = page_addr; + info->ndcb2 = 0; + + break; + case NAND_CMD_RESET: + info->ndcb0 |= NDCB0_CMD_TYPE(5) + | command; + + break; + + case NAND_CMD_ERASE2: + exec_cmd = 0; + break; + + default: + exec_cmd = 0; + dev_err(&info->pdev->dev, "non-supported command %x\n", + command); + break; + } + + return exec_cmd; +} + +static void nand_cmdfunc(struct mtd_info *mtd, unsigned command, + int column, int page_addr) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + int exec_cmd; + + /* + * if this is a x16 device ,then convert the input + * "byte" address into a "word" address appropriate + * for indexing a word-oriented device + */ + if (info->reg_ndcr & NDCR_DWIDTH_M) + column /= 2; + + /* + * There may be different NAND chip hooked to + * different chip select, so check whether + * chip select has been changed, if yes, reset the timing + */ + if (info->cs != host->cs) { + info->cs = host->cs; + nand_writel(info, NDTR0CS0, info->ndtr0cs0); + nand_writel(info, NDTR1CS0, info->ndtr1cs0); + } + + prepare_start_command(info, command); + + info->state = STATE_PREPARED; + exec_cmd = prepare_set_command(info, command, 0, column, page_addr); + + if (exec_cmd) { + init_completion(&info->cmd_complete); + init_completion(&info->dev_ready); + info->need_wait = 1; + pxa3xx_nand_start(info); + + if (!wait_for_completion_timeout(&info->cmd_complete, + CHIP_DELAY_TIMEOUT)) { + dev_err(&info->pdev->dev, "Wait time out!!!\n"); + /* Stop State Machine for next command cycle */ + pxa3xx_nand_stop(info); + } + } + info->state = STATE_IDLE; +} + +static void nand_cmdfunc_extended(struct mtd_info *mtd, + const unsigned command, + int column, int page_addr) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + int exec_cmd, ext_cmd_type; + + /* + * if this is a x16 device then convert the input + * "byte" address into a "word" address appropriate + * for indexing a word-oriented device + */ + if (info->reg_ndcr & NDCR_DWIDTH_M) + column /= 2; + + /* + * There may be different NAND chip hooked to + * different chip select, so check whether + * chip select has been changed, if yes, reset the timing + */ + if (info->cs != host->cs) { + info->cs = host->cs; + nand_writel(info, NDTR0CS0, info->ndtr0cs0); + nand_writel(info, NDTR1CS0, info->ndtr1cs0); + } + + /* Select the extended command for the first command */ + switch (command) { + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + ext_cmd_type = EXT_CMD_TYPE_MONO; + break; + case NAND_CMD_SEQIN: + ext_cmd_type = EXT_CMD_TYPE_DISPATCH; + break; + case NAND_CMD_PAGEPROG: + ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; + break; + default: + ext_cmd_type = 0; + break; + } + + prepare_start_command(info, command); + + /* + * Prepare the "is ready" completion before starting a command + * transaction sequence. If the command is not executed the + * completion will be completed, see below. + * + * We can do that inside the loop because the command variable + * is invariant and thus so is the exec_cmd. + */ + info->need_wait = 1; + init_completion(&info->dev_ready); + do { + info->state = STATE_PREPARED; + exec_cmd = prepare_set_command(info, command, ext_cmd_type, + column, page_addr); + if (!exec_cmd) { + info->need_wait = 0; + complete(&info->dev_ready); + break; + } + + init_completion(&info->cmd_complete); + pxa3xx_nand_start(info); + + if (!wait_for_completion_timeout(&info->cmd_complete, + CHIP_DELAY_TIMEOUT)) { + dev_err(&info->pdev->dev, "Wait time out!!!\n"); + /* Stop State Machine for next command cycle */ + pxa3xx_nand_stop(info); + break; + } + + /* Check if the sequence is complete */ + if (info->data_size == 0 && command != NAND_CMD_PAGEPROG) + break; + + /* + * After a splitted program command sequence has issued + * the command dispatch, the command sequence is complete. + */ + if (info->data_size == 0 && + command == NAND_CMD_PAGEPROG && + ext_cmd_type == EXT_CMD_TYPE_DISPATCH) + break; + + if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) { + /* Last read: issue a 'last naked read' */ + if (info->data_size == info->chunk_size) + ext_cmd_type = EXT_CMD_TYPE_LAST_RW; + else + ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; + + /* + * If a splitted program command has no more data to transfer, + * the command dispatch must be issued to complete. + */ + } else if (command == NAND_CMD_PAGEPROG && + info->data_size == 0) { + ext_cmd_type = EXT_CMD_TYPE_DISPATCH; + } + } while (1); + + info->state = STATE_IDLE; +} + +static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf, int oob_required) +{ + chip->write_buf(mtd, buf, mtd->writesize); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int oob_required, + int page) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + + chip->read_buf(mtd, buf, mtd->writesize); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (info->retcode == ERR_CORERR && info->use_ecc) { + mtd->ecc_stats.corrected += info->ecc_err_cnt; + + } else if (info->retcode == ERR_UNCORERR) { + /* + * for blank page (all 0xff), HW will calculate its ECC as + * 0, which is different from the ECC information within + * OOB, ignore such uncorrectable errors + */ + if (is_buf_blank(buf, mtd->writesize)) + info->retcode = ERR_NONE; + else + mtd->ecc_stats.failed++; + } + + return info->max_bitflips; +} + +static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + char retval = 0xFF; + + if (info->buf_start < info->buf_count) + /* Has just send a new command? */ + retval = info->data_buff[info->buf_start++]; + + return retval; +} + +static u16 pxa3xx_nand_read_word(struct mtd_info *mtd) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + u16 retval = 0xFFFF; + + if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) { + retval = *((u16 *)(info->data_buff+info->buf_start)); + info->buf_start += 2; + } + return retval; +} + +static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + int real_len = min_t(size_t, len, info->buf_count - info->buf_start); + + memcpy(buf, info->data_buff + info->buf_start, real_len); + info->buf_start += real_len; +} + +static void pxa3xx_nand_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + int real_len = min_t(size_t, len, info->buf_count - info->buf_start); + + memcpy(info->data_buff + info->buf_start, buf, real_len); + info->buf_start += real_len; +} + +static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip) +{ + return; +} + +static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + + if (info->need_wait) { + info->need_wait = 0; + if (!wait_for_completion_timeout(&info->dev_ready, + CHIP_DELAY_TIMEOUT)) { + dev_err(&info->pdev->dev, "Ready time out!!!\n"); + return NAND_STATUS_FAIL; + } + } + + /* pxa3xx_nand_send_command has waited for command complete */ + if (this->state == FL_WRITING || this->state == FL_ERASING) { + if (info->retcode == ERR_NONE) + return 0; + else + return NAND_STATUS_FAIL; + } + + return NAND_STATUS_READY; +} + +static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, + const struct pxa3xx_nand_flash *f) +{ + struct platform_device *pdev = info->pdev; + struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + struct pxa3xx_nand_host *host = info->host[info->cs]; + uint32_t ndcr = 0x0; /* enable all interrupts */ + + if (f->page_size != 2048 && f->page_size != 512) { + dev_err(&pdev->dev, "Current only support 2048 and 512 size\n"); + return -EINVAL; + } + + if (f->flash_width != 16 && f->flash_width != 8) { + dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n"); + return -EINVAL; + } + + /* calculate flash information */ + host->read_id_bytes = (f->page_size == 2048) ? 4 : 2; + + /* calculate addressing information */ + host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1; + + if (f->num_blocks * f->page_per_block > 65536) + host->row_addr_cycles = 3; + else + host->row_addr_cycles = 2; + + ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; + ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0; + ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0; + ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0; + ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0; + ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; + + ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes); + ndcr |= NDCR_SPARE_EN; /* enable spare by default */ + + info->reg_ndcr = ndcr; + + pxa3xx_nand_set_timing(host, f->timing); + return 0; +} + +static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) +{ + /* + * We set 0 by hard coding here, for we don't support keep_config + * when there is more than one chip attached to the controller + */ + struct pxa3xx_nand_host *host = info->host[0]; + uint32_t ndcr = nand_readl(info, NDCR); + + if (ndcr & NDCR_PAGE_SZ) { + /* Controller's FIFO size */ + info->chunk_size = 2048; + host->read_id_bytes = 4; + } else { + info->chunk_size = 512; + host->read_id_bytes = 2; + } + + /* Set an initial chunk size */ + info->reg_ndcr = ndcr & ~NDCR_INT_MASK; + info->ndtr0cs0 = nand_readl(info, NDTR0CS0); + info->ndtr1cs0 = nand_readl(info, NDTR1CS0); + return 0; +} + +#ifdef ARCH_HAS_DMA +static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) +{ + struct platform_device *pdev = info->pdev; + int data_desc_offset = info->buf_size - sizeof(struct pxa_dma_desc); + + if (use_dma == 0) { + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); + if (info->data_buff == NULL) + return -ENOMEM; + return 0; + } + + info->data_buff = dma_alloc_coherent(&pdev->dev, info->buf_size, + &info->data_buff_phys, GFP_KERNEL); + if (info->data_buff == NULL) { + dev_err(&pdev->dev, "failed to allocate dma buffer\n"); + return -ENOMEM; + } + + info->data_desc = (void *)info->data_buff + data_desc_offset; + info->data_desc_addr = info->data_buff_phys + data_desc_offset; + + info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW, + pxa3xx_nand_data_dma_irq, info); + if (info->data_dma_ch < 0) { + dev_err(&pdev->dev, "failed to request data dma\n"); + dma_free_coherent(&pdev->dev, info->buf_size, + info->data_buff, info->data_buff_phys); + return info->data_dma_ch; + } + + /* + * Now that DMA buffers are allocated we turn on + * DMA proper for I/O operations. + */ + info->use_dma = 1; + return 0; +} + +static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) +{ + struct platform_device *pdev = info->pdev; + if (info->use_dma) { + pxa_free_dma(info->data_dma_ch); + dma_free_coherent(&pdev->dev, info->buf_size, + info->data_buff, info->data_buff_phys); + } else { + kfree(info->data_buff); + } +} +#else +static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) +{ + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); + if (info->data_buff == NULL) + return -ENOMEM; + return 0; +} + +static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) +{ + kfree(info->data_buff); +} +#endif + +static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info) +{ + struct mtd_info *mtd; + struct nand_chip *chip; + int ret; + + mtd = info->host[info->cs]->mtd; + chip = mtd->priv; + + /* use the common timing to make a try */ + ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]); + if (ret) + return ret; + + chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0); + ret = chip->waitfunc(mtd, chip); + if (ret & NAND_STATUS_FAIL) + return -ENODEV; + + return 0; +} + +static int pxa_ecc_init(struct pxa3xx_nand_info *info, + struct nand_ecc_ctrl *ecc, + int strength, int ecc_stepsize, int page_size) +{ + if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) { + info->chunk_size = 2048; + info->spare_size = 40; + info->ecc_size = 24; + ecc->mode = NAND_ECC_HW; + ecc->size = 512; + ecc->strength = 1; + + } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) { + info->chunk_size = 512; + info->spare_size = 8; + info->ecc_size = 8; + ecc->mode = NAND_ECC_HW; + ecc->size = 512; + ecc->strength = 1; + + /* + * Required ECC: 4-bit correction per 512 bytes + * Select: 16-bit correction per 2048 bytes + */ + } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) { + info->ecc_bch = 1; + info->chunk_size = 2048; + info->spare_size = 32; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_2KB_bch4bit; + ecc->strength = 16; + + } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) { + info->ecc_bch = 1; + info->chunk_size = 2048; + info->spare_size = 32; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_4KB_bch4bit; + ecc->strength = 16; + + /* + * Required ECC: 8-bit correction per 512 bytes + * Select: 16-bit correction per 1024 bytes + */ + } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) { + info->ecc_bch = 1; + info->chunk_size = 1024; + info->spare_size = 0; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_4KB_bch8bit; + ecc->strength = 16; + } else { + dev_err(&info->pdev->dev, + "ECC strength %d at page size %d is not supported\n", + strength, page_size); + return -ENODEV; + } + + dev_info(&info->pdev->dev, "ECC strength %d, ECC step size %d\n", + ecc->strength, ecc->size); + return 0; +} + +static int pxa3xx_nand_scan(struct mtd_info *mtd) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + struct platform_device *pdev = info->pdev; + struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL; + const struct pxa3xx_nand_flash *f = NULL; + struct nand_chip *chip = mtd->priv; + uint32_t id = -1; + uint64_t chipsize; + int i, ret, num; + uint16_t ecc_strength, ecc_step; + + if (pdata->keep_config && !pxa3xx_nand_detect_config(info)) + goto KEEP_CONFIG; + + ret = pxa3xx_nand_sensing(info); + if (ret) { + dev_info(&info->pdev->dev, "There is no chip on cs %d!\n", + info->cs); + + return ret; + } + + chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0); + id = *((uint16_t *)(info->data_buff)); + if (id != 0) + dev_info(&info->pdev->dev, "Detect a flash id %x\n", id); + else { + dev_warn(&info->pdev->dev, + "Read out ID 0, potential timing set wrong!!\n"); + + return -EINVAL; + } + + num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1; + for (i = 0; i < num; i++) { + if (i < pdata->num_flash) + f = pdata->flash + i; + else + f = &builtin_flash_types[i - pdata->num_flash + 1]; + + /* find the chip in default list */ + if (f->chip_id == id) + break; + } + + if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) { + dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n"); + + return -EINVAL; + } + + ret = pxa3xx_nand_config_flash(info, f); + if (ret) { + dev_err(&info->pdev->dev, "ERROR! Configure failed\n"); + return ret; + } + + memset(pxa3xx_flash_ids, 0, sizeof(pxa3xx_flash_ids)); + + pxa3xx_flash_ids[0].name = f->name; + pxa3xx_flash_ids[0].dev_id = (f->chip_id >> 8) & 0xffff; + pxa3xx_flash_ids[0].pagesize = f->page_size; + chipsize = (uint64_t)f->num_blocks * f->page_per_block * f->page_size; + pxa3xx_flash_ids[0].chipsize = chipsize >> 20; + pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block; + if (f->flash_width == 16) + pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16; + pxa3xx_flash_ids[1].name = NULL; + def = pxa3xx_flash_ids; +KEEP_CONFIG: + if (info->reg_ndcr & NDCR_DWIDTH_M) + chip->options |= NAND_BUSWIDTH_16; + + /* Device detection must be done with ECC disabled */ + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) + nand_writel(info, NDECCCTRL, 0x0); + + if (nand_scan_ident(mtd, 1, def)) + return -ENODEV; + + if (pdata->flash_bbt) { + /* + * We'll use a bad block table stored in-flash and don't + * allow writing the bad block marker to the flash. + */ + chip->bbt_options |= NAND_BBT_USE_FLASH | + NAND_BBT_NO_OOB_BBM; + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + } + + /* + * If the page size is bigger than the FIFO size, let's check + * we are given the right variant and then switch to the extended + * (aka splitted) command handling, + */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) { + chip->cmdfunc = nand_cmdfunc_extended; + } else { + dev_err(&info->pdev->dev, + "unsupported page size on this variant\n"); + return -ENODEV; + } + } + + if (pdata->ecc_strength && pdata->ecc_step_size) { + ecc_strength = pdata->ecc_strength; + ecc_step = pdata->ecc_step_size; + } else { + ecc_strength = chip->ecc_strength_ds; + ecc_step = chip->ecc_step_ds; + } + + /* Set default ECC strength requirements on non-ONFI devices */ + if (ecc_strength < 1 && ecc_step < 1) { + ecc_strength = 1; + ecc_step = 512; + } + + ret = pxa_ecc_init(info, &chip->ecc, ecc_strength, + ecc_step, mtd->writesize); + if (ret) + return ret; + + /* calculate addressing information */ + if (mtd->writesize >= 2048) + host->col_addr_cycles = 2; + else + host->col_addr_cycles = 1; + + /* release the initial buffer */ + kfree(info->data_buff); + + /* allocate the real data + oob buffer */ + info->buf_size = mtd->writesize + mtd->oobsize; + ret = pxa3xx_nand_init_buff(info); + if (ret) + return ret; + info->oob_buff = info->data_buff + mtd->writesize; + + if ((mtd->size >> chip->page_shift) > 65536) + host->row_addr_cycles = 3; + else + host->row_addr_cycles = 2; + return nand_scan_tail(mtd); +} + +static int alloc_nand_resource(struct platform_device *pdev) +{ + struct pxa3xx_nand_platform_data *pdata; + struct pxa3xx_nand_info *info; + struct pxa3xx_nand_host *host; + struct nand_chip *chip = NULL; + struct mtd_info *mtd; + struct resource *r; + int ret, irq, cs; + + pdata = dev_get_platdata(&pdev->dev); + if (pdata->num_cs <= 0) + return -ENODEV; + info = devm_kzalloc(&pdev->dev, sizeof(*info) + (sizeof(*mtd) + + sizeof(*host)) * pdata->num_cs, GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->pdev = pdev; + info->variant = pxa3xx_nand_get_variant(pdev); + for (cs = 0; cs < pdata->num_cs; cs++) { + mtd = (struct mtd_info *)((unsigned int)&info[1] + + (sizeof(*mtd) + sizeof(*host)) * cs); + chip = (struct nand_chip *)(&mtd[1]); + host = (struct pxa3xx_nand_host *)chip; + info->host[cs] = host; + host->mtd = mtd; + host->cs = cs; + host->info_data = info; + mtd->priv = host; + mtd->owner = THIS_MODULE; + + chip->ecc.read_page = pxa3xx_nand_read_page_hwecc; + chip->ecc.write_page = pxa3xx_nand_write_page_hwecc; + chip->controller = &info->controller; + chip->waitfunc = pxa3xx_nand_waitfunc; + chip->select_chip = pxa3xx_nand_select_chip; + chip->read_word = pxa3xx_nand_read_word; + chip->read_byte = pxa3xx_nand_read_byte; + chip->read_buf = pxa3xx_nand_read_buf; + chip->write_buf = pxa3xx_nand_write_buf; + chip->options |= NAND_NO_SUBPAGE_WRITE; + chip->cmdfunc = nand_cmdfunc; + } + + spin_lock_init(&chip->controller->lock); + init_waitqueue_head(&chip->controller->wq); + info->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(info->clk)) { + dev_err(&pdev->dev, "failed to get nand clock\n"); + return PTR_ERR(info->clk); + } + ret = clk_prepare_enable(info->clk); + if (ret < 0) + return ret; + + if (use_dma) { + /* + * This is a dirty hack to make this driver work from + * devicetree bindings. It can be removed once we have + * a prober DMA controller framework for DT. + */ + if (pdev->dev.of_node && + of_machine_is_compatible("marvell,pxa3xx")) { + info->drcmr_dat = 97; + info->drcmr_cmd = 99; + } else { + r = platform_get_resource(pdev, IORESOURCE_DMA, 0); + if (r == NULL) { + dev_err(&pdev->dev, + "no resource defined for data DMA\n"); + ret = -ENXIO; + goto fail_disable_clk; + } + info->drcmr_dat = r->start; + + r = platform_get_resource(pdev, IORESOURCE_DMA, 1); + if (r == NULL) { + dev_err(&pdev->dev, + "no resource defined for cmd DMA\n"); + ret = -ENXIO; + goto fail_disable_clk; + } + info->drcmr_cmd = r->start; + } + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "no IRQ resource defined\n"); + ret = -ENXIO; + goto fail_disable_clk; + } + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + info->mmio_base = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(info->mmio_base)) { + ret = PTR_ERR(info->mmio_base); + goto fail_disable_clk; + } + info->mmio_phys = r->start; + + /* Allocate a buffer to allow flash detection */ + info->buf_size = INIT_BUFFER_SIZE; + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); + if (info->data_buff == NULL) { + ret = -ENOMEM; + goto fail_disable_clk; + } + + /* initialize all interrupts to be disabled */ + disable_int(info, NDSR_MASK); + + ret = request_threaded_irq(irq, pxa3xx_nand_irq, + pxa3xx_nand_irq_thread, IRQF_ONESHOT, + pdev->name, info); + if (ret < 0) { + dev_err(&pdev->dev, "failed to request IRQ\n"); + goto fail_free_buf; + } + + platform_set_drvdata(pdev, info); + + return 0; + +fail_free_buf: + free_irq(irq, info); + kfree(info->data_buff); +fail_disable_clk: + clk_disable_unprepare(info->clk); + return ret; +} + +static int pxa3xx_nand_remove(struct platform_device *pdev) +{ + struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); + struct pxa3xx_nand_platform_data *pdata; + int irq, cs; + + if (!info) + return 0; + + pdata = dev_get_platdata(&pdev->dev); + + irq = platform_get_irq(pdev, 0); + if (irq >= 0) + free_irq(irq, info); + pxa3xx_nand_free_buff(info); + + clk_disable_unprepare(info->clk); + + for (cs = 0; cs < pdata->num_cs; cs++) + nand_release(info->host[cs]->mtd); + return 0; +} + +static int pxa3xx_nand_probe_dt(struct platform_device *pdev) +{ + struct pxa3xx_nand_platform_data *pdata; + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *of_id = + of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); + + if (!of_id) + return 0; + + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + + if (of_get_property(np, "marvell,nand-enable-arbiter", NULL)) + pdata->enable_arbiter = 1; + if (of_get_property(np, "marvell,nand-keep-config", NULL)) + pdata->keep_config = 1; + of_property_read_u32(np, "num-cs", &pdata->num_cs); + pdata->flash_bbt = of_get_nand_on_flash_bbt(np); + + pdata->ecc_strength = of_get_nand_ecc_strength(np); + if (pdata->ecc_strength < 0) + pdata->ecc_strength = 0; + + pdata->ecc_step_size = of_get_nand_ecc_step_size(np); + if (pdata->ecc_step_size < 0) + pdata->ecc_step_size = 0; + + pdev->dev.platform_data = pdata; + + return 0; +} + +static int pxa3xx_nand_probe(struct platform_device *pdev) +{ + struct pxa3xx_nand_platform_data *pdata; + struct mtd_part_parser_data ppdata = {}; + struct pxa3xx_nand_info *info; + int ret, cs, probe_success; + +#ifndef ARCH_HAS_DMA + if (use_dma) { + use_dma = 0; + dev_warn(&pdev->dev, + "This platform can't do DMA on this device\n"); + } +#endif + ret = pxa3xx_nand_probe_dt(pdev); + if (ret) + return ret; + + pdata = dev_get_platdata(&pdev->dev); + if (!pdata) { + dev_err(&pdev->dev, "no platform data defined\n"); + return -ENODEV; + } + + ret = alloc_nand_resource(pdev); + if (ret) { + dev_err(&pdev->dev, "alloc nand resource failed\n"); + return ret; + } + + info = platform_get_drvdata(pdev); + probe_success = 0; + for (cs = 0; cs < pdata->num_cs; cs++) { + struct mtd_info *mtd = info->host[cs]->mtd; + + /* + * The mtd name matches the one used in 'mtdparts' kernel + * parameter. This name cannot be changed or otherwise + * user's mtd partitions configuration would get broken. + */ + mtd->name = "pxa3xx_nand-0"; + info->cs = cs; + ret = pxa3xx_nand_scan(mtd); + if (ret) { + dev_warn(&pdev->dev, "failed to scan nand at cs %d\n", + cs); + continue; + } + + ppdata.of_node = pdev->dev.of_node; + ret = mtd_device_parse_register(mtd, NULL, + &ppdata, pdata->parts[cs], + pdata->nr_parts[cs]); + if (!ret) + probe_success = 1; + } + + if (!probe_success) { + pxa3xx_nand_remove(pdev); + return -ENODEV; + } + + return 0; +} + +#ifdef CONFIG_PM +static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); + struct pxa3xx_nand_platform_data *pdata; + struct mtd_info *mtd; + int cs; + + pdata = dev_get_platdata(&pdev->dev); + if (info->state) { + dev_err(&pdev->dev, "driver busy, state = %d\n", info->state); + return -EAGAIN; + } + + for (cs = 0; cs < pdata->num_cs; cs++) { + mtd = info->host[cs]->mtd; + mtd_suspend(mtd); + } + + return 0; +} + +static int pxa3xx_nand_resume(struct platform_device *pdev) +{ + struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); + struct pxa3xx_nand_platform_data *pdata; + struct mtd_info *mtd; + int cs; + + pdata = dev_get_platdata(&pdev->dev); + /* We don't want to handle interrupt without calling mtd routine */ + disable_int(info, NDCR_INT_MASK); + + /* + * Directly set the chip select to a invalid value, + * then the driver would reset the timing according + * to current chip select at the beginning of cmdfunc + */ + info->cs = 0xff; + + /* + * As the spec says, the NDSR would be updated to 0x1800 when + * doing the nand_clk disable/enable. + * To prevent it damaging state machine of the driver, clear + * all status before resume + */ + nand_writel(info, NDSR, NDSR_MASK); + for (cs = 0; cs < pdata->num_cs; cs++) { + mtd = info->host[cs]->mtd; + mtd_resume(mtd); + } + + return 0; +} +#else +#define pxa3xx_nand_suspend NULL +#define pxa3xx_nand_resume NULL +#endif + +static struct platform_driver pxa3xx_nand_driver = { + .driver = { + .name = "pxa3xx-nand", + .of_match_table = pxa3xx_nand_dt_ids, + }, + .probe = pxa3xx_nand_probe, + .remove = pxa3xx_nand_remove, + .suspend = pxa3xx_nand_suspend, + .resume = pxa3xx_nand_resume, +}; + +module_platform_driver(pxa3xx_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("PXA3xx NAND controller driver"); diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/r852.c new file mode 100644 index 000000000..baea83f4d --- /dev/null +++ b/drivers/mtd/nand/r852.c @@ -0,0 +1,1085 @@ +/* + * Copyright © 2009 - Maxim Levitsky + * driver for Ricoh xD readers + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/jiffies.h> +#include <linux/workqueue.h> +#include <linux/interrupt.h> +#include <linux/pci.h> +#include <linux/pci_ids.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <asm/byteorder.h> +#include <linux/sched.h> +#include "sm_common.h" +#include "r852.h" + + +static bool r852_enable_dma = 1; +module_param(r852_enable_dma, bool, S_IRUGO); +MODULE_PARM_DESC(r852_enable_dma, "Enable usage of the DMA (default)"); + +static int debug; +module_param(debug, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(debug, "Debug level (0-2)"); + +/* read register */ +static inline uint8_t r852_read_reg(struct r852_device *dev, int address) +{ + uint8_t reg = readb(dev->mmio + address); + return reg; +} + +/* write register */ +static inline void r852_write_reg(struct r852_device *dev, + int address, uint8_t value) +{ + writeb(value, dev->mmio + address); + mmiowb(); +} + + +/* read dword sized register */ +static inline uint32_t r852_read_reg_dword(struct r852_device *dev, int address) +{ + uint32_t reg = le32_to_cpu(readl(dev->mmio + address)); + return reg; +} + +/* write dword sized register */ +static inline void r852_write_reg_dword(struct r852_device *dev, + int address, uint32_t value) +{ + writel(cpu_to_le32(value), dev->mmio + address); + mmiowb(); +} + +/* returns pointer to our private structure */ +static inline struct r852_device *r852_get_dev(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + return chip->priv; +} + + +/* check if controller supports dma */ +static void r852_dma_test(struct r852_device *dev) +{ + dev->dma_usable = (r852_read_reg(dev, R852_DMA_CAP) & + (R852_DMA1 | R852_DMA2)) == (R852_DMA1 | R852_DMA2); + + if (!dev->dma_usable) + message("Non dma capable device detected, dma disabled"); + + if (!r852_enable_dma) { + message("disabling dma on user request"); + dev->dma_usable = 0; + } +} + +/* + * Enable dma. Enables ether first or second stage of the DMA, + * Expects dev->dma_dir and dev->dma_state be set + */ +static void r852_dma_enable(struct r852_device *dev) +{ + uint8_t dma_reg, dma_irq_reg; + + /* Set up dma settings */ + dma_reg = r852_read_reg_dword(dev, R852_DMA_SETTINGS); + dma_reg &= ~(R852_DMA_READ | R852_DMA_INTERNAL | R852_DMA_MEMORY); + + if (dev->dma_dir) + dma_reg |= R852_DMA_READ; + + if (dev->dma_state == DMA_INTERNAL) { + dma_reg |= R852_DMA_INTERNAL; + /* Precaution to make sure HW doesn't write */ + /* to random kernel memory */ + r852_write_reg_dword(dev, R852_DMA_ADDR, + cpu_to_le32(dev->phys_bounce_buffer)); + } else { + dma_reg |= R852_DMA_MEMORY; + r852_write_reg_dword(dev, R852_DMA_ADDR, + cpu_to_le32(dev->phys_dma_addr)); + } + + /* Precaution: make sure write reached the device */ + r852_read_reg_dword(dev, R852_DMA_ADDR); + + r852_write_reg_dword(dev, R852_DMA_SETTINGS, dma_reg); + + /* Set dma irq */ + dma_irq_reg = r852_read_reg_dword(dev, R852_DMA_IRQ_ENABLE); + r852_write_reg_dword(dev, R852_DMA_IRQ_ENABLE, + dma_irq_reg | + R852_DMA_IRQ_INTERNAL | + R852_DMA_IRQ_ERROR | + R852_DMA_IRQ_MEMORY); +} + +/* + * Disable dma, called from the interrupt handler, which specifies + * success of the operation via 'error' argument + */ +static void r852_dma_done(struct r852_device *dev, int error) +{ + WARN_ON(dev->dma_stage == 0); + + r852_write_reg_dword(dev, R852_DMA_IRQ_STA, + r852_read_reg_dword(dev, R852_DMA_IRQ_STA)); + + r852_write_reg_dword(dev, R852_DMA_SETTINGS, 0); + r852_write_reg_dword(dev, R852_DMA_IRQ_ENABLE, 0); + + /* Precaution to make sure HW doesn't write to random kernel memory */ + r852_write_reg_dword(dev, R852_DMA_ADDR, + cpu_to_le32(dev->phys_bounce_buffer)); + r852_read_reg_dword(dev, R852_DMA_ADDR); + + dev->dma_error = error; + dev->dma_stage = 0; + + if (dev->phys_dma_addr && dev->phys_dma_addr != dev->phys_bounce_buffer) + pci_unmap_single(dev->pci_dev, dev->phys_dma_addr, R852_DMA_LEN, + dev->dma_dir ? PCI_DMA_FROMDEVICE : PCI_DMA_TODEVICE); +} + +/* + * Wait, till dma is done, which includes both phases of it + */ +static int r852_dma_wait(struct r852_device *dev) +{ + long timeout = wait_for_completion_timeout(&dev->dma_done, + msecs_to_jiffies(1000)); + if (!timeout) { + dbg("timeout waiting for DMA interrupt"); + return -ETIMEDOUT; + } + + return 0; +} + +/* + * Read/Write one page using dma. Only pages can be read (512 bytes) +*/ +static void r852_do_dma(struct r852_device *dev, uint8_t *buf, int do_read) +{ + int bounce = 0; + unsigned long flags; + int error; + + dev->dma_error = 0; + + /* Set dma direction */ + dev->dma_dir = do_read; + dev->dma_stage = 1; + reinit_completion(&dev->dma_done); + + dbg_verbose("doing dma %s ", do_read ? "read" : "write"); + + /* Set initial dma state: for reading first fill on board buffer, + from device, for writes first fill the buffer from memory*/ + dev->dma_state = do_read ? DMA_INTERNAL : DMA_MEMORY; + + /* if incoming buffer is not page aligned, we should do bounce */ + if ((unsigned long)buf & (R852_DMA_LEN-1)) + bounce = 1; + + if (!bounce) { + dev->phys_dma_addr = pci_map_single(dev->pci_dev, (void *)buf, + R852_DMA_LEN, + (do_read ? PCI_DMA_FROMDEVICE : PCI_DMA_TODEVICE)); + + if (pci_dma_mapping_error(dev->pci_dev, dev->phys_dma_addr)) + bounce = 1; + } + + if (bounce) { + dbg_verbose("dma: using bounce buffer"); + dev->phys_dma_addr = dev->phys_bounce_buffer; + if (!do_read) + memcpy(dev->bounce_buffer, buf, R852_DMA_LEN); + } + + /* Enable DMA */ + spin_lock_irqsave(&dev->irqlock, flags); + r852_dma_enable(dev); + spin_unlock_irqrestore(&dev->irqlock, flags); + + /* Wait till complete */ + error = r852_dma_wait(dev); + + if (error) { + r852_dma_done(dev, error); + return; + } + + if (do_read && bounce) + memcpy((void *)buf, dev->bounce_buffer, R852_DMA_LEN); +} + +/* + * Program data lines of the nand chip to send data to it + */ +static void r852_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct r852_device *dev = r852_get_dev(mtd); + uint32_t reg; + + /* Don't allow any access to hardware if we suspect card removal */ + if (dev->card_unstable) + return; + + /* Special case for whole sector read */ + if (len == R852_DMA_LEN && dev->dma_usable) { + r852_do_dma(dev, (uint8_t *)buf, 0); + return; + } + + /* write DWORD chinks - faster */ + while (len >= 4) { + reg = buf[0] | buf[1] << 8 | buf[2] << 16 | buf[3] << 24; + r852_write_reg_dword(dev, R852_DATALINE, reg); + buf += 4; + len -= 4; + + } + + /* write rest */ + while (len > 0) { + r852_write_reg(dev, R852_DATALINE, *buf++); + len--; + } +} + +/* + * Read data lines of the nand chip to retrieve data + */ +static void r852_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct r852_device *dev = r852_get_dev(mtd); + uint32_t reg; + + if (dev->card_unstable) { + /* since we can't signal error here, at least, return + predictable buffer */ + memset(buf, 0, len); + return; + } + + /* special case for whole sector read */ + if (len == R852_DMA_LEN && dev->dma_usable) { + r852_do_dma(dev, buf, 1); + return; + } + + /* read in dword sized chunks */ + while (len >= 4) { + + reg = r852_read_reg_dword(dev, R852_DATALINE); + *buf++ = reg & 0xFF; + *buf++ = (reg >> 8) & 0xFF; + *buf++ = (reg >> 16) & 0xFF; + *buf++ = (reg >> 24) & 0xFF; + len -= 4; + } + + /* read the reset by bytes */ + while (len--) + *buf++ = r852_read_reg(dev, R852_DATALINE); +} + +/* + * Read one byte from nand chip + */ +static uint8_t r852_read_byte(struct mtd_info *mtd) +{ + struct r852_device *dev = r852_get_dev(mtd); + + /* Same problem as in r852_read_buf.... */ + if (dev->card_unstable) + return 0; + + return r852_read_reg(dev, R852_DATALINE); +} + +/* + * Control several chip lines & send commands + */ +static void r852_cmdctl(struct mtd_info *mtd, int dat, unsigned int ctrl) +{ + struct r852_device *dev = r852_get_dev(mtd); + + if (dev->card_unstable) + return; + + if (ctrl & NAND_CTRL_CHANGE) { + + dev->ctlreg &= ~(R852_CTL_DATA | R852_CTL_COMMAND | + R852_CTL_ON | R852_CTL_CARDENABLE); + + if (ctrl & NAND_ALE) + dev->ctlreg |= R852_CTL_DATA; + + if (ctrl & NAND_CLE) + dev->ctlreg |= R852_CTL_COMMAND; + + if (ctrl & NAND_NCE) + dev->ctlreg |= (R852_CTL_CARDENABLE | R852_CTL_ON); + else + dev->ctlreg &= ~R852_CTL_WRITE; + + /* when write is stareted, enable write access */ + if (dat == NAND_CMD_ERASE1) + dev->ctlreg |= R852_CTL_WRITE; + + r852_write_reg(dev, R852_CTL, dev->ctlreg); + } + + /* HACK: NAND_CMD_SEQIN is called without NAND_CTRL_CHANGE, but we need + to set write mode */ + if (dat == NAND_CMD_SEQIN && (dev->ctlreg & R852_CTL_COMMAND)) { + dev->ctlreg |= R852_CTL_WRITE; + r852_write_reg(dev, R852_CTL, dev->ctlreg); + } + + if (dat != NAND_CMD_NONE) + r852_write_reg(dev, R852_DATALINE, dat); +} + +/* + * Wait till card is ready. + * based on nand_wait, but returns errors on DMA error + */ +static int r852_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct r852_device *dev = chip->priv; + + unsigned long timeout; + int status; + + timeout = jiffies + (chip->state == FL_ERASING ? + msecs_to_jiffies(400) : msecs_to_jiffies(20)); + + while (time_before(jiffies, timeout)) + if (chip->dev_ready(mtd)) + break; + + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + status = (int)chip->read_byte(mtd); + + /* Unfortunelly, no way to send detailed error status... */ + if (dev->dma_error) { + status |= NAND_STATUS_FAIL; + dev->dma_error = 0; + } + return status; +} + +/* + * Check if card is ready + */ + +static int r852_ready(struct mtd_info *mtd) +{ + struct r852_device *dev = r852_get_dev(mtd); + return !(r852_read_reg(dev, R852_CARD_STA) & R852_CARD_STA_BUSY); +} + + +/* + * Set ECC engine mode +*/ + +static void r852_ecc_hwctl(struct mtd_info *mtd, int mode) +{ + struct r852_device *dev = r852_get_dev(mtd); + + if (dev->card_unstable) + return; + + switch (mode) { + case NAND_ECC_READ: + case NAND_ECC_WRITE: + /* enable ecc generation/check*/ + dev->ctlreg |= R852_CTL_ECC_ENABLE; + + /* flush ecc buffer */ + r852_write_reg(dev, R852_CTL, + dev->ctlreg | R852_CTL_ECC_ACCESS); + + r852_read_reg_dword(dev, R852_DATALINE); + r852_write_reg(dev, R852_CTL, dev->ctlreg); + return; + + case NAND_ECC_READSYN: + /* disable ecc generation */ + dev->ctlreg &= ~R852_CTL_ECC_ENABLE; + r852_write_reg(dev, R852_CTL, dev->ctlreg); + } +} + +/* + * Calculate ECC, only used for writes + */ + +static int r852_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat, + uint8_t *ecc_code) +{ + struct r852_device *dev = r852_get_dev(mtd); + struct sm_oob *oob = (struct sm_oob *)ecc_code; + uint32_t ecc1, ecc2; + + if (dev->card_unstable) + return 0; + + dev->ctlreg &= ~R852_CTL_ECC_ENABLE; + r852_write_reg(dev, R852_CTL, dev->ctlreg | R852_CTL_ECC_ACCESS); + + ecc1 = r852_read_reg_dword(dev, R852_DATALINE); + ecc2 = r852_read_reg_dword(dev, R852_DATALINE); + + oob->ecc1[0] = (ecc1) & 0xFF; + oob->ecc1[1] = (ecc1 >> 8) & 0xFF; + oob->ecc1[2] = (ecc1 >> 16) & 0xFF; + + oob->ecc2[0] = (ecc2) & 0xFF; + oob->ecc2[1] = (ecc2 >> 8) & 0xFF; + oob->ecc2[2] = (ecc2 >> 16) & 0xFF; + + r852_write_reg(dev, R852_CTL, dev->ctlreg); + return 0; +} + +/* + * Correct the data using ECC, hw did almost everything for us + */ + +static int r852_ecc_correct(struct mtd_info *mtd, uint8_t *dat, + uint8_t *read_ecc, uint8_t *calc_ecc) +{ + uint16_t ecc_reg; + uint8_t ecc_status, err_byte; + int i, error = 0; + + struct r852_device *dev = r852_get_dev(mtd); + + if (dev->card_unstable) + return 0; + + if (dev->dma_error) { + dev->dma_error = 0; + return -1; + } + + r852_write_reg(dev, R852_CTL, dev->ctlreg | R852_CTL_ECC_ACCESS); + ecc_reg = r852_read_reg_dword(dev, R852_DATALINE); + r852_write_reg(dev, R852_CTL, dev->ctlreg); + + for (i = 0 ; i <= 1 ; i++) { + + ecc_status = (ecc_reg >> 8) & 0xFF; + + /* ecc uncorrectable error */ + if (ecc_status & R852_ECC_FAIL) { + dbg("ecc: unrecoverable error, in half %d", i); + error = -1; + goto exit; + } + + /* correctable error */ + if (ecc_status & R852_ECC_CORRECTABLE) { + + err_byte = ecc_reg & 0xFF; + dbg("ecc: recoverable error, " + "in half %d, byte %d, bit %d", i, + err_byte, ecc_status & R852_ECC_ERR_BIT_MSK); + + dat[err_byte] ^= + 1 << (ecc_status & R852_ECC_ERR_BIT_MSK); + error++; + } + + dat += 256; + ecc_reg >>= 16; + } +exit: + return error; +} + +/* + * This is copy of nand_read_oob_std + * nand_read_oob_syndrome assumes we can send column address - we can't + */ +static int r852_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +/* + * Start the nand engine + */ + +static void r852_engine_enable(struct r852_device *dev) +{ + if (r852_read_reg_dword(dev, R852_HW) & R852_HW_UNKNOWN) { + r852_write_reg(dev, R852_CTL, R852_CTL_RESET | R852_CTL_ON); + r852_write_reg_dword(dev, R852_HW, R852_HW_ENABLED); + } else { + r852_write_reg_dword(dev, R852_HW, R852_HW_ENABLED); + r852_write_reg(dev, R852_CTL, R852_CTL_RESET | R852_CTL_ON); + } + msleep(300); + r852_write_reg(dev, R852_CTL, 0); +} + + +/* + * Stop the nand engine + */ + +static void r852_engine_disable(struct r852_device *dev) +{ + r852_write_reg_dword(dev, R852_HW, 0); + r852_write_reg(dev, R852_CTL, R852_CTL_RESET); +} + +/* + * Test if card is present + */ + +static void r852_card_update_present(struct r852_device *dev) +{ + unsigned long flags; + uint8_t reg; + + spin_lock_irqsave(&dev->irqlock, flags); + reg = r852_read_reg(dev, R852_CARD_STA); + dev->card_detected = !!(reg & R852_CARD_STA_PRESENT); + spin_unlock_irqrestore(&dev->irqlock, flags); +} + +/* + * Update card detection IRQ state according to current card state + * which is read in r852_card_update_present + */ +static void r852_update_card_detect(struct r852_device *dev) +{ + int card_detect_reg = r852_read_reg(dev, R852_CARD_IRQ_ENABLE); + dev->card_unstable = 0; + + card_detect_reg &= ~(R852_CARD_IRQ_REMOVE | R852_CARD_IRQ_INSERT); + card_detect_reg |= R852_CARD_IRQ_GENABLE; + + card_detect_reg |= dev->card_detected ? + R852_CARD_IRQ_REMOVE : R852_CARD_IRQ_INSERT; + + r852_write_reg(dev, R852_CARD_IRQ_ENABLE, card_detect_reg); +} + +static ssize_t r852_media_type_show(struct device *sys_dev, + struct device_attribute *attr, char *buf) +{ + struct mtd_info *mtd = container_of(sys_dev, struct mtd_info, dev); + struct r852_device *dev = r852_get_dev(mtd); + char *data = dev->sm ? "smartmedia" : "xd"; + + strcpy(buf, data); + return strlen(data); +} + +static DEVICE_ATTR(media_type, S_IRUGO, r852_media_type_show, NULL); + + +/* Detect properties of card in slot */ +static void r852_update_media_status(struct r852_device *dev) +{ + uint8_t reg; + unsigned long flags; + int readonly; + + spin_lock_irqsave(&dev->irqlock, flags); + if (!dev->card_detected) { + message("card removed"); + spin_unlock_irqrestore(&dev->irqlock, flags); + return ; + } + + readonly = r852_read_reg(dev, R852_CARD_STA) & R852_CARD_STA_RO; + reg = r852_read_reg(dev, R852_DMA_CAP); + dev->sm = (reg & (R852_DMA1 | R852_DMA2)) && (reg & R852_SMBIT); + + message("detected %s %s card in slot", + dev->sm ? "SmartMedia" : "xD", + readonly ? "readonly" : "writeable"); + + dev->readonly = readonly; + spin_unlock_irqrestore(&dev->irqlock, flags); +} + +/* + * Register the nand device + * Called when the card is detected + */ +static int r852_register_nand_device(struct r852_device *dev) +{ + dev->mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL); + + if (!dev->mtd) + goto error1; + + WARN_ON(dev->card_registred); + + dev->mtd->owner = THIS_MODULE; + dev->mtd->priv = dev->chip; + dev->mtd->dev.parent = &dev->pci_dev->dev; + + if (dev->readonly) + dev->chip->options |= NAND_ROM; + + r852_engine_enable(dev); + + if (sm_register_device(dev->mtd, dev->sm)) + goto error2; + + if (device_create_file(&dev->mtd->dev, &dev_attr_media_type)) + message("can't create media type sysfs attribute"); + + dev->card_registred = 1; + return 0; +error2: + kfree(dev->mtd); +error1: + /* Force card redetect */ + dev->card_detected = 0; + return -1; +} + +/* + * Unregister the card + */ + +static void r852_unregister_nand_device(struct r852_device *dev) +{ + if (!dev->card_registred) + return; + + device_remove_file(&dev->mtd->dev, &dev_attr_media_type); + nand_release(dev->mtd); + r852_engine_disable(dev); + dev->card_registred = 0; + kfree(dev->mtd); + dev->mtd = NULL; +} + +/* Card state updater */ +static void r852_card_detect_work(struct work_struct *work) +{ + struct r852_device *dev = + container_of(work, struct r852_device, card_detect_work.work); + + r852_card_update_present(dev); + r852_update_card_detect(dev); + dev->card_unstable = 0; + + /* False alarm */ + if (dev->card_detected == dev->card_registred) + goto exit; + + /* Read media properties */ + r852_update_media_status(dev); + + /* Register the card */ + if (dev->card_detected) + r852_register_nand_device(dev); + else + r852_unregister_nand_device(dev); +exit: + r852_update_card_detect(dev); +} + +/* Ack + disable IRQ generation */ +static void r852_disable_irqs(struct r852_device *dev) +{ + uint8_t reg; + reg = r852_read_reg(dev, R852_CARD_IRQ_ENABLE); + r852_write_reg(dev, R852_CARD_IRQ_ENABLE, reg & ~R852_CARD_IRQ_MASK); + + reg = r852_read_reg_dword(dev, R852_DMA_IRQ_ENABLE); + r852_write_reg_dword(dev, R852_DMA_IRQ_ENABLE, + reg & ~R852_DMA_IRQ_MASK); + + r852_write_reg(dev, R852_CARD_IRQ_STA, R852_CARD_IRQ_MASK); + r852_write_reg_dword(dev, R852_DMA_IRQ_STA, R852_DMA_IRQ_MASK); +} + +/* Interrupt handler */ +static irqreturn_t r852_irq(int irq, void *data) +{ + struct r852_device *dev = (struct r852_device *)data; + + uint8_t card_status, dma_status; + unsigned long flags; + irqreturn_t ret = IRQ_NONE; + + spin_lock_irqsave(&dev->irqlock, flags); + + /* handle card detection interrupts first */ + card_status = r852_read_reg(dev, R852_CARD_IRQ_STA); + r852_write_reg(dev, R852_CARD_IRQ_STA, card_status); + + if (card_status & (R852_CARD_IRQ_INSERT|R852_CARD_IRQ_REMOVE)) { + + ret = IRQ_HANDLED; + dev->card_detected = !!(card_status & R852_CARD_IRQ_INSERT); + + /* we shouldn't receive any interrupts if we wait for card + to settle */ + WARN_ON(dev->card_unstable); + + /* disable irqs while card is unstable */ + /* this will timeout DMA if active, but better that garbage */ + r852_disable_irqs(dev); + + if (dev->card_unstable) + goto out; + + /* let, card state to settle a bit, and then do the work */ + dev->card_unstable = 1; + queue_delayed_work(dev->card_workqueue, + &dev->card_detect_work, msecs_to_jiffies(100)); + goto out; + } + + + /* Handle dma interrupts */ + dma_status = r852_read_reg_dword(dev, R852_DMA_IRQ_STA); + r852_write_reg_dword(dev, R852_DMA_IRQ_STA, dma_status); + + if (dma_status & R852_DMA_IRQ_MASK) { + + ret = IRQ_HANDLED; + + if (dma_status & R852_DMA_IRQ_ERROR) { + dbg("received dma error IRQ"); + r852_dma_done(dev, -EIO); + complete(&dev->dma_done); + goto out; + } + + /* received DMA interrupt out of nowhere? */ + WARN_ON_ONCE(dev->dma_stage == 0); + + if (dev->dma_stage == 0) + goto out; + + /* done device access */ + if (dev->dma_state == DMA_INTERNAL && + (dma_status & R852_DMA_IRQ_INTERNAL)) { + + dev->dma_state = DMA_MEMORY; + dev->dma_stage++; + } + + /* done memory DMA */ + if (dev->dma_state == DMA_MEMORY && + (dma_status & R852_DMA_IRQ_MEMORY)) { + dev->dma_state = DMA_INTERNAL; + dev->dma_stage++; + } + + /* Enable 2nd half of dma dance */ + if (dev->dma_stage == 2) + r852_dma_enable(dev); + + /* Operation done */ + if (dev->dma_stage == 3) { + r852_dma_done(dev, 0); + complete(&dev->dma_done); + } + goto out; + } + + /* Handle unknown interrupts */ + if (dma_status) + dbg("bad dma IRQ status = %x", dma_status); + + if (card_status & ~R852_CARD_STA_CD) + dbg("strange card status = %x", card_status); + +out: + spin_unlock_irqrestore(&dev->irqlock, flags); + return ret; +} + +static int r852_probe(struct pci_dev *pci_dev, const struct pci_device_id *id) +{ + int error; + struct nand_chip *chip; + struct r852_device *dev; + + /* pci initialization */ + error = pci_enable_device(pci_dev); + + if (error) + goto error1; + + pci_set_master(pci_dev); + + error = pci_set_dma_mask(pci_dev, DMA_BIT_MASK(32)); + if (error) + goto error2; + + error = pci_request_regions(pci_dev, DRV_NAME); + + if (error) + goto error3; + + error = -ENOMEM; + + /* init nand chip, but register it only on card insert */ + chip = kzalloc(sizeof(struct nand_chip), GFP_KERNEL); + + if (!chip) + goto error4; + + /* commands */ + chip->cmd_ctrl = r852_cmdctl; + chip->waitfunc = r852_wait; + chip->dev_ready = r852_ready; + + /* I/O */ + chip->read_byte = r852_read_byte; + chip->read_buf = r852_read_buf; + chip->write_buf = r852_write_buf; + + /* ecc */ + chip->ecc.mode = NAND_ECC_HW_SYNDROME; + chip->ecc.size = R852_DMA_LEN; + chip->ecc.bytes = SM_OOB_SIZE; + chip->ecc.strength = 2; + chip->ecc.hwctl = r852_ecc_hwctl; + chip->ecc.calculate = r852_ecc_calculate; + chip->ecc.correct = r852_ecc_correct; + + /* TODO: hack */ + chip->ecc.read_oob = r852_read_oob; + + /* init our device structure */ + dev = kzalloc(sizeof(struct r852_device), GFP_KERNEL); + + if (!dev) + goto error5; + + chip->priv = dev; + dev->chip = chip; + dev->pci_dev = pci_dev; + pci_set_drvdata(pci_dev, dev); + + dev->bounce_buffer = pci_alloc_consistent(pci_dev, R852_DMA_LEN, + &dev->phys_bounce_buffer); + + if (!dev->bounce_buffer) + goto error6; + + + error = -ENODEV; + dev->mmio = pci_ioremap_bar(pci_dev, 0); + + if (!dev->mmio) + goto error7; + + error = -ENOMEM; + dev->tmp_buffer = kzalloc(SM_SECTOR_SIZE, GFP_KERNEL); + + if (!dev->tmp_buffer) + goto error8; + + init_completion(&dev->dma_done); + + dev->card_workqueue = create_freezable_workqueue(DRV_NAME); + + if (!dev->card_workqueue) + goto error9; + + INIT_DELAYED_WORK(&dev->card_detect_work, r852_card_detect_work); + + /* shutdown everything - precation */ + r852_engine_disable(dev); + r852_disable_irqs(dev); + + r852_dma_test(dev); + + dev->irq = pci_dev->irq; + spin_lock_init(&dev->irqlock); + + dev->card_detected = 0; + r852_card_update_present(dev); + + /*register irq handler*/ + error = -ENODEV; + if (request_irq(pci_dev->irq, &r852_irq, IRQF_SHARED, + DRV_NAME, dev)) + goto error10; + + /* kick initial present test */ + queue_delayed_work(dev->card_workqueue, + &dev->card_detect_work, 0); + + + printk(KERN_NOTICE DRV_NAME ": driver loaded successfully\n"); + return 0; + +error10: + destroy_workqueue(dev->card_workqueue); +error9: + kfree(dev->tmp_buffer); +error8: + pci_iounmap(pci_dev, dev->mmio); +error7: + pci_free_consistent(pci_dev, R852_DMA_LEN, + dev->bounce_buffer, dev->phys_bounce_buffer); +error6: + kfree(dev); +error5: + kfree(chip); +error4: + pci_release_regions(pci_dev); +error3: +error2: + pci_disable_device(pci_dev); +error1: + return error; +} + +static void r852_remove(struct pci_dev *pci_dev) +{ + struct r852_device *dev = pci_get_drvdata(pci_dev); + + /* Stop detect workqueue - + we are going to unregister the device anyway*/ + cancel_delayed_work_sync(&dev->card_detect_work); + destroy_workqueue(dev->card_workqueue); + + /* Unregister the device, this might make more IO */ + r852_unregister_nand_device(dev); + + /* Stop interrupts */ + r852_disable_irqs(dev); + synchronize_irq(dev->irq); + free_irq(dev->irq, dev); + + /* Cleanup */ + kfree(dev->tmp_buffer); + pci_iounmap(pci_dev, dev->mmio); + pci_free_consistent(pci_dev, R852_DMA_LEN, + dev->bounce_buffer, dev->phys_bounce_buffer); + + kfree(dev->chip); + kfree(dev); + + /* Shutdown the PCI device */ + pci_release_regions(pci_dev); + pci_disable_device(pci_dev); +} + +static void r852_shutdown(struct pci_dev *pci_dev) +{ + struct r852_device *dev = pci_get_drvdata(pci_dev); + + cancel_delayed_work_sync(&dev->card_detect_work); + r852_disable_irqs(dev); + synchronize_irq(dev->irq); + pci_disable_device(pci_dev); +} + +#ifdef CONFIG_PM_SLEEP +static int r852_suspend(struct device *device) +{ + struct r852_device *dev = pci_get_drvdata(to_pci_dev(device)); + + if (dev->ctlreg & R852_CTL_CARDENABLE) + return -EBUSY; + + /* First make sure the detect work is gone */ + cancel_delayed_work_sync(&dev->card_detect_work); + + /* Turn off the interrupts and stop the device */ + r852_disable_irqs(dev); + r852_engine_disable(dev); + + /* If card was pulled off just during the suspend, which is very + unlikely, we will remove it on resume, it too late now + anyway... */ + dev->card_unstable = 0; + return 0; +} + +static int r852_resume(struct device *device) +{ + struct r852_device *dev = pci_get_drvdata(to_pci_dev(device)); + + r852_disable_irqs(dev); + r852_card_update_present(dev); + r852_engine_disable(dev); + + + /* If card status changed, just do the work */ + if (dev->card_detected != dev->card_registred) { + dbg("card was %s during low power state", + dev->card_detected ? "added" : "removed"); + + queue_delayed_work(dev->card_workqueue, + &dev->card_detect_work, msecs_to_jiffies(1000)); + return 0; + } + + /* Otherwise, initialize the card */ + if (dev->card_registred) { + r852_engine_enable(dev); + dev->chip->select_chip(dev->mtd, 0); + dev->chip->cmdfunc(dev->mtd, NAND_CMD_RESET, -1, -1); + dev->chip->select_chip(dev->mtd, -1); + } + + /* Program card detection IRQ */ + r852_update_card_detect(dev); + return 0; +} +#endif + +static const struct pci_device_id r852_pci_id_tbl[] = { + + { PCI_VDEVICE(RICOH, 0x0852), }, + { }, +}; + +MODULE_DEVICE_TABLE(pci, r852_pci_id_tbl); + +static SIMPLE_DEV_PM_OPS(r852_pm_ops, r852_suspend, r852_resume); + +static struct pci_driver r852_pci_driver = { + .name = DRV_NAME, + .id_table = r852_pci_id_tbl, + .probe = r852_probe, + .remove = r852_remove, + .shutdown = r852_shutdown, + .driver.pm = &r852_pm_ops, +}; + +module_pci_driver(r852_pci_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Maxim Levitsky <maximlevitsky@gmail.com>"); +MODULE_DESCRIPTION("Ricoh 85xx xD/smartmedia card reader driver"); diff --git a/drivers/mtd/nand/r852.h b/drivers/mtd/nand/r852.h new file mode 100644 index 000000000..e6a21d9d2 --- /dev/null +++ b/drivers/mtd/nand/r852.h @@ -0,0 +1,161 @@ +/* + * Copyright © 2009 - Maxim Levitsky + * driver for Ricoh xD readers + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/pci.h> +#include <linux/completion.h> +#include <linux/workqueue.h> +#include <linux/mtd/nand.h> +#include <linux/spinlock.h> + + +/* nand interface + ecc + byte write/read does one cycle on nand data lines. + dword write/read does 4 cycles + if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads + results of ecc correction, if DMA read was done before. + If write was done two dword reads read generated ecc checksums +*/ +#define R852_DATALINE 0x00 + +/* control register */ +#define R852_CTL 0x04 +#define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/ +#define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/ +#define R852_CTL_ON 0x04 /* only seem to controls the hd led, */ + /* but has to be set on start...*/ +#define R852_CTL_RESET 0x08 /* unknown, set only on start once*/ +#define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/ +#define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */ +#define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/ +#define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */ + +/* card detection status */ +#define R852_CARD_STA 0x05 + +#define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */ +#define R852_CARD_STA_RO 0x02 /* card is readonly */ +#define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */ +#define R852_CARD_STA_ABSENT 0x08 /* card is absent */ +#define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */ + +/* card detection irq status & enable*/ +#define R852_CARD_IRQ_STA 0x06 /* IRQ status */ +#define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */ + +#define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/ +#define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */ +#define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */ +#define R852_CARD_IRQ_UNK1 0x10 /* unknown */ +#define R852_CARD_IRQ_GENABLE 0x80 /* general enable */ +#define R852_CARD_IRQ_MASK 0x1D + + + +/* hardware enable */ +#define R852_HW 0x08 +#define R852_HW_ENABLED 0x01 /* hw enabled */ +#define R852_HW_UNKNOWN 0x80 + + +/* dma capabilities */ +#define R852_DMA_CAP 0x09 +#define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */ + /* hw is smartmedia */ +#define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */ +#define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */ + + +/* physical DMA address - 32 bit value*/ +#define R852_DMA_ADDR 0x0C + + +/* dma settings */ +#define R852_DMA_SETTINGS 0x10 +#define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */ +#define R852_DMA_READ 0x02 /* 0 = write, 1 = read */ +#define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */ + +/* dma IRQ status */ +#define R852_DMA_IRQ_STA 0x14 + +/* dma IRQ enable */ +#define R852_DMA_IRQ_ENABLE 0x18 + +#define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */ +#define R852_DMA_IRQ_ERROR 0x02 /* error did happen */ +#define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */ +#define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */ + + +/* ECC syndrome format - read from reg #0 will return two copies of these for + each half of the page. + first byte is error byte location, and second, bit location + flags */ +#define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */ +#define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */ +#define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */ +#define R852_ECC_FAIL 0x40 /* non correctable error detected */ + +#define R852_DMA_LEN 512 + +#define DMA_INTERNAL 0 +#define DMA_MEMORY 1 + +struct r852_device { + void __iomem *mmio; /* mmio */ + struct mtd_info *mtd; /* mtd backpointer */ + struct nand_chip *chip; /* nand chip backpointer */ + struct pci_dev *pci_dev; /* pci backpointer */ + + /* dma area */ + dma_addr_t phys_dma_addr; /* bus address of buffer*/ + struct completion dma_done; /* data transfer done */ + + dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */ + uint8_t *bounce_buffer; /* virtual address of bounce buffer */ + + int dma_dir; /* 1 = read, 0 = write */ + int dma_stage; /* 0 - idle, 1 - first step, + 2 - second step */ + + int dma_state; /* 0 = internal, 1 = memory */ + int dma_error; /* dma errors */ + int dma_usable; /* is it possible to use dma */ + + /* card status area */ + struct delayed_work card_detect_work; + struct workqueue_struct *card_workqueue; + int card_registred; /* card registered with mtd */ + int card_detected; /* card detected in slot */ + int card_unstable; /* whenever the card is inserted, + is not known yet */ + int readonly; /* card is readonly */ + int sm; /* Is card smartmedia */ + + /* interrupt handling */ + spinlock_t irqlock; /* IRQ protecting lock */ + int irq; /* irq num */ + /* misc */ + void *tmp_buffer; /* temporary buffer */ + uint8_t ctlreg; /* cached contents of control reg */ +}; + +#define DRV_NAME "r852" + + +#define dbg(format, ...) \ + if (debug) \ + printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__) + +#define dbg_verbose(format, ...) \ + if (debug > 1) \ + printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__) + + +#define message(format, ...) \ + printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__) diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c new file mode 100644 index 000000000..0e02be47c --- /dev/null +++ b/drivers/mtd/nand/s3c2410.c @@ -0,0 +1,1142 @@ +/* linux/drivers/mtd/nand/s3c2410.c + * + * Copyright © 2004-2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * Samsung S3C2410/S3C2440/S3C2412 NAND driver + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#define pr_fmt(fmt) "nand-s3c2410: " fmt + +#ifdef CONFIG_MTD_NAND_S3C2410_DEBUG +#define DEBUG +#endif + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/clk.h> +#include <linux/cpufreq.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> + +#include <linux/platform_data/mtd-nand-s3c2410.h> + +#define S3C2410_NFREG(x) (x) + +#define S3C2410_NFCONF S3C2410_NFREG(0x00) +#define S3C2410_NFCMD S3C2410_NFREG(0x04) +#define S3C2410_NFADDR S3C2410_NFREG(0x08) +#define S3C2410_NFDATA S3C2410_NFREG(0x0C) +#define S3C2410_NFSTAT S3C2410_NFREG(0x10) +#define S3C2410_NFECC S3C2410_NFREG(0x14) +#define S3C2440_NFCONT S3C2410_NFREG(0x04) +#define S3C2440_NFCMD S3C2410_NFREG(0x08) +#define S3C2440_NFADDR S3C2410_NFREG(0x0C) +#define S3C2440_NFDATA S3C2410_NFREG(0x10) +#define S3C2440_NFSTAT S3C2410_NFREG(0x20) +#define S3C2440_NFMECC0 S3C2410_NFREG(0x2C) +#define S3C2412_NFSTAT S3C2410_NFREG(0x28) +#define S3C2412_NFMECC0 S3C2410_NFREG(0x34) +#define S3C2410_NFCONF_EN (1<<15) +#define S3C2410_NFCONF_INITECC (1<<12) +#define S3C2410_NFCONF_nFCE (1<<11) +#define S3C2410_NFCONF_TACLS(x) ((x)<<8) +#define S3C2410_NFCONF_TWRPH0(x) ((x)<<4) +#define S3C2410_NFCONF_TWRPH1(x) ((x)<<0) +#define S3C2410_NFSTAT_BUSY (1<<0) +#define S3C2440_NFCONF_TACLS(x) ((x)<<12) +#define S3C2440_NFCONF_TWRPH0(x) ((x)<<8) +#define S3C2440_NFCONF_TWRPH1(x) ((x)<<4) +#define S3C2440_NFCONT_INITECC (1<<4) +#define S3C2440_NFCONT_nFCE (1<<1) +#define S3C2440_NFCONT_ENABLE (1<<0) +#define S3C2440_NFSTAT_READY (1<<0) +#define S3C2412_NFCONF_NANDBOOT (1<<31) +#define S3C2412_NFCONT_INIT_MAIN_ECC (1<<5) +#define S3C2412_NFCONT_nFCE0 (1<<1) +#define S3C2412_NFSTAT_READY (1<<0) + +/* new oob placement block for use with hardware ecc generation + */ + +static struct nand_ecclayout nand_hw_eccoob = { + .eccbytes = 3, + .eccpos = {0, 1, 2}, + .oobfree = {{8, 8}} +}; + +/* controller and mtd information */ + +struct s3c2410_nand_info; + +/** + * struct s3c2410_nand_mtd - driver MTD structure + * @mtd: The MTD instance to pass to the MTD layer. + * @chip: The NAND chip information. + * @set: The platform information supplied for this set of NAND chips. + * @info: Link back to the hardware information. + * @scan_res: The result from calling nand_scan_ident(). +*/ +struct s3c2410_nand_mtd { + struct mtd_info mtd; + struct nand_chip chip; + struct s3c2410_nand_set *set; + struct s3c2410_nand_info *info; + int scan_res; +}; + +enum s3c_cpu_type { + TYPE_S3C2410, + TYPE_S3C2412, + TYPE_S3C2440, +}; + +enum s3c_nand_clk_state { + CLOCK_DISABLE = 0, + CLOCK_ENABLE, + CLOCK_SUSPEND, +}; + +/* overview of the s3c2410 nand state */ + +/** + * struct s3c2410_nand_info - NAND controller state. + * @mtds: An array of MTD instances on this controoler. + * @platform: The platform data for this board. + * @device: The platform device we bound to. + * @clk: The clock resource for this controller. + * @regs: The area mapped for the hardware registers. + * @sel_reg: Pointer to the register controlling the NAND selection. + * @sel_bit: The bit in @sel_reg to select the NAND chip. + * @mtd_count: The number of MTDs created from this controller. + * @save_sel: The contents of @sel_reg to be saved over suspend. + * @clk_rate: The clock rate from @clk. + * @clk_state: The current clock state. + * @cpu_type: The exact type of this controller. + */ +struct s3c2410_nand_info { + /* mtd info */ + struct nand_hw_control controller; + struct s3c2410_nand_mtd *mtds; + struct s3c2410_platform_nand *platform; + + /* device info */ + struct device *device; + struct clk *clk; + void __iomem *regs; + void __iomem *sel_reg; + int sel_bit; + int mtd_count; + unsigned long save_sel; + unsigned long clk_rate; + enum s3c_nand_clk_state clk_state; + + enum s3c_cpu_type cpu_type; + +#ifdef CONFIG_CPU_FREQ + struct notifier_block freq_transition; +#endif +}; + +/* conversion functions */ + +static struct s3c2410_nand_mtd *s3c2410_nand_mtd_toours(struct mtd_info *mtd) +{ + return container_of(mtd, struct s3c2410_nand_mtd, mtd); +} + +static struct s3c2410_nand_info *s3c2410_nand_mtd_toinfo(struct mtd_info *mtd) +{ + return s3c2410_nand_mtd_toours(mtd)->info; +} + +static struct s3c2410_nand_info *to_nand_info(struct platform_device *dev) +{ + return platform_get_drvdata(dev); +} + +static struct s3c2410_platform_nand *to_nand_plat(struct platform_device *dev) +{ + return dev_get_platdata(&dev->dev); +} + +static inline int allow_clk_suspend(struct s3c2410_nand_info *info) +{ +#ifdef CONFIG_MTD_NAND_S3C2410_CLKSTOP + return 1; +#else + return 0; +#endif +} + +/** + * s3c2410_nand_clk_set_state - Enable, disable or suspend NAND clock. + * @info: The controller instance. + * @new_state: State to which clock should be set. + */ +static void s3c2410_nand_clk_set_state(struct s3c2410_nand_info *info, + enum s3c_nand_clk_state new_state) +{ + if (!allow_clk_suspend(info) && new_state == CLOCK_SUSPEND) + return; + + if (info->clk_state == CLOCK_ENABLE) { + if (new_state != CLOCK_ENABLE) + clk_disable_unprepare(info->clk); + } else { + if (new_state == CLOCK_ENABLE) + clk_prepare_enable(info->clk); + } + + info->clk_state = new_state; +} + +/* timing calculations */ + +#define NS_IN_KHZ 1000000 + +/** + * s3c_nand_calc_rate - calculate timing data. + * @wanted: The cycle time in nanoseconds. + * @clk: The clock rate in kHz. + * @max: The maximum divider value. + * + * Calculate the timing value from the given parameters. + */ +static int s3c_nand_calc_rate(int wanted, unsigned long clk, int max) +{ + int result; + + result = DIV_ROUND_UP((wanted * clk), NS_IN_KHZ); + + pr_debug("result %d from %ld, %d\n", result, clk, wanted); + + if (result > max) { + pr_err("%d ns is too big for current clock rate %ld\n", + wanted, clk); + return -1; + } + + if (result < 1) + result = 1; + + return result; +} + +#define to_ns(ticks, clk) (((ticks) * NS_IN_KHZ) / (unsigned int)(clk)) + +/* controller setup */ + +/** + * s3c2410_nand_setrate - setup controller timing information. + * @info: The controller instance. + * + * Given the information supplied by the platform, calculate and set + * the necessary timing registers in the hardware to generate the + * necessary timing cycles to the hardware. + */ +static int s3c2410_nand_setrate(struct s3c2410_nand_info *info) +{ + struct s3c2410_platform_nand *plat = info->platform; + int tacls_max = (info->cpu_type == TYPE_S3C2412) ? 8 : 4; + int tacls, twrph0, twrph1; + unsigned long clkrate = clk_get_rate(info->clk); + unsigned long uninitialized_var(set), cfg, uninitialized_var(mask); + unsigned long flags; + + /* calculate the timing information for the controller */ + + info->clk_rate = clkrate; + clkrate /= 1000; /* turn clock into kHz for ease of use */ + + if (plat != NULL) { + tacls = s3c_nand_calc_rate(plat->tacls, clkrate, tacls_max); + twrph0 = s3c_nand_calc_rate(plat->twrph0, clkrate, 8); + twrph1 = s3c_nand_calc_rate(plat->twrph1, clkrate, 8); + } else { + /* default timings */ + tacls = tacls_max; + twrph0 = 8; + twrph1 = 8; + } + + if (tacls < 0 || twrph0 < 0 || twrph1 < 0) { + dev_err(info->device, "cannot get suitable timings\n"); + return -EINVAL; + } + + dev_info(info->device, "Tacls=%d, %dns Twrph0=%d %dns, Twrph1=%d %dns\n", + tacls, to_ns(tacls, clkrate), twrph0, to_ns(twrph0, clkrate), + twrph1, to_ns(twrph1, clkrate)); + + switch (info->cpu_type) { + case TYPE_S3C2410: + mask = (S3C2410_NFCONF_TACLS(3) | + S3C2410_NFCONF_TWRPH0(7) | + S3C2410_NFCONF_TWRPH1(7)); + set = S3C2410_NFCONF_EN; + set |= S3C2410_NFCONF_TACLS(tacls - 1); + set |= S3C2410_NFCONF_TWRPH0(twrph0 - 1); + set |= S3C2410_NFCONF_TWRPH1(twrph1 - 1); + break; + + case TYPE_S3C2440: + case TYPE_S3C2412: + mask = (S3C2440_NFCONF_TACLS(tacls_max - 1) | + S3C2440_NFCONF_TWRPH0(7) | + S3C2440_NFCONF_TWRPH1(7)); + + set = S3C2440_NFCONF_TACLS(tacls - 1); + set |= S3C2440_NFCONF_TWRPH0(twrph0 - 1); + set |= S3C2440_NFCONF_TWRPH1(twrph1 - 1); + break; + + default: + BUG(); + } + + local_irq_save(flags); + + cfg = readl(info->regs + S3C2410_NFCONF); + cfg &= ~mask; + cfg |= set; + writel(cfg, info->regs + S3C2410_NFCONF); + + local_irq_restore(flags); + + dev_dbg(info->device, "NF_CONF is 0x%lx\n", cfg); + + return 0; +} + +/** + * s3c2410_nand_inithw - basic hardware initialisation + * @info: The hardware state. + * + * Do the basic initialisation of the hardware, using s3c2410_nand_setrate() + * to setup the hardware access speeds and set the controller to be enabled. +*/ +static int s3c2410_nand_inithw(struct s3c2410_nand_info *info) +{ + int ret; + + ret = s3c2410_nand_setrate(info); + if (ret < 0) + return ret; + + switch (info->cpu_type) { + case TYPE_S3C2410: + default: + break; + + case TYPE_S3C2440: + case TYPE_S3C2412: + /* enable the controller and de-assert nFCE */ + + writel(S3C2440_NFCONT_ENABLE, info->regs + S3C2440_NFCONT); + } + + return 0; +} + +/** + * s3c2410_nand_select_chip - select the given nand chip + * @mtd: The MTD instance for this chip. + * @chip: The chip number. + * + * This is called by the MTD layer to either select a given chip for the + * @mtd instance, or to indicate that the access has finished and the + * chip can be de-selected. + * + * The routine ensures that the nFCE line is correctly setup, and any + * platform specific selection code is called to route nFCE to the specific + * chip. + */ +static void s3c2410_nand_select_chip(struct mtd_info *mtd, int chip) +{ + struct s3c2410_nand_info *info; + struct s3c2410_nand_mtd *nmtd; + struct nand_chip *this = mtd->priv; + unsigned long cur; + + nmtd = this->priv; + info = nmtd->info; + + if (chip != -1) + s3c2410_nand_clk_set_state(info, CLOCK_ENABLE); + + cur = readl(info->sel_reg); + + if (chip == -1) { + cur |= info->sel_bit; + } else { + if (nmtd->set != NULL && chip > nmtd->set->nr_chips) { + dev_err(info->device, "invalid chip %d\n", chip); + return; + } + + if (info->platform != NULL) { + if (info->platform->select_chip != NULL) + (info->platform->select_chip) (nmtd->set, chip); + } + + cur &= ~info->sel_bit; + } + + writel(cur, info->sel_reg); + + if (chip == -1) + s3c2410_nand_clk_set_state(info, CLOCK_SUSPEND); +} + +/* s3c2410_nand_hwcontrol + * + * Issue command and address cycles to the chip +*/ + +static void s3c2410_nand_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writeb(cmd, info->regs + S3C2410_NFCMD); + else + writeb(cmd, info->regs + S3C2410_NFADDR); +} + +/* command and control functions */ + +static void s3c2440_nand_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writeb(cmd, info->regs + S3C2440_NFCMD); + else + writeb(cmd, info->regs + S3C2440_NFADDR); +} + +/* s3c2410_nand_devready() + * + * returns 0 if the nand is busy, 1 if it is ready +*/ + +static int s3c2410_nand_devready(struct mtd_info *mtd) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + return readb(info->regs + S3C2410_NFSTAT) & S3C2410_NFSTAT_BUSY; +} + +static int s3c2440_nand_devready(struct mtd_info *mtd) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + return readb(info->regs + S3C2440_NFSTAT) & S3C2440_NFSTAT_READY; +} + +static int s3c2412_nand_devready(struct mtd_info *mtd) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + return readb(info->regs + S3C2412_NFSTAT) & S3C2412_NFSTAT_READY; +} + +/* ECC handling functions */ + +#ifdef CONFIG_MTD_NAND_S3C2410_HWECC +static int s3c2410_nand_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned int diff0, diff1, diff2; + unsigned int bit, byte; + + pr_debug("%s(%p,%p,%p,%p)\n", __func__, mtd, dat, read_ecc, calc_ecc); + + diff0 = read_ecc[0] ^ calc_ecc[0]; + diff1 = read_ecc[1] ^ calc_ecc[1]; + diff2 = read_ecc[2] ^ calc_ecc[2]; + + pr_debug("%s: rd %*phN calc %*phN diff %02x%02x%02x\n", + __func__, 3, read_ecc, 3, calc_ecc, + diff0, diff1, diff2); + + if (diff0 == 0 && diff1 == 0 && diff2 == 0) + return 0; /* ECC is ok */ + + /* sometimes people do not think about using the ECC, so check + * to see if we have an 0xff,0xff,0xff read ECC and then ignore + * the error, on the assumption that this is an un-eccd page. + */ + if (read_ecc[0] == 0xff && read_ecc[1] == 0xff && read_ecc[2] == 0xff + && info->platform->ignore_unset_ecc) + return 0; + + /* Can we correct this ECC (ie, one row and column change). + * Note, this is similar to the 256 error code on smartmedia */ + + if (((diff0 ^ (diff0 >> 1)) & 0x55) == 0x55 && + ((diff1 ^ (diff1 >> 1)) & 0x55) == 0x55 && + ((diff2 ^ (diff2 >> 1)) & 0x55) == 0x55) { + /* calculate the bit position of the error */ + + bit = ((diff2 >> 3) & 1) | + ((diff2 >> 4) & 2) | + ((diff2 >> 5) & 4); + + /* calculate the byte position of the error */ + + byte = ((diff2 << 7) & 0x100) | + ((diff1 << 0) & 0x80) | + ((diff1 << 1) & 0x40) | + ((diff1 << 2) & 0x20) | + ((diff1 << 3) & 0x10) | + ((diff0 >> 4) & 0x08) | + ((diff0 >> 3) & 0x04) | + ((diff0 >> 2) & 0x02) | + ((diff0 >> 1) & 0x01); + + dev_dbg(info->device, "correcting error bit %d, byte %d\n", + bit, byte); + + dat[byte] ^= (1 << bit); + return 1; + } + + /* if there is only one bit difference in the ECC, then + * one of only a row or column parity has changed, which + * means the error is most probably in the ECC itself */ + + diff0 |= (diff1 << 8); + diff0 |= (diff2 << 16); + + if ((diff0 & ~(1<<fls(diff0))) == 0) + return 1; + + return -1; +} + +/* ECC functions + * + * These allow the s3c2410 and s3c2440 to use the controller's ECC + * generator block to ECC the data as it passes through] +*/ + +static void s3c2410_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned long ctrl; + + ctrl = readl(info->regs + S3C2410_NFCONF); + ctrl |= S3C2410_NFCONF_INITECC; + writel(ctrl, info->regs + S3C2410_NFCONF); +} + +static void s3c2412_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned long ctrl; + + ctrl = readl(info->regs + S3C2440_NFCONT); + writel(ctrl | S3C2412_NFCONT_INIT_MAIN_ECC, + info->regs + S3C2440_NFCONT); +} + +static void s3c2440_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned long ctrl; + + ctrl = readl(info->regs + S3C2440_NFCONT); + writel(ctrl | S3C2440_NFCONT_INITECC, info->regs + S3C2440_NFCONT); +} + +static int s3c2410_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + + ecc_code[0] = readb(info->regs + S3C2410_NFECC + 0); + ecc_code[1] = readb(info->regs + S3C2410_NFECC + 1); + ecc_code[2] = readb(info->regs + S3C2410_NFECC + 2); + + pr_debug("%s: returning ecc %*phN\n", __func__, 3, ecc_code); + + return 0; +} + +static int s3c2412_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned long ecc = readl(info->regs + S3C2412_NFMECC0); + + ecc_code[0] = ecc; + ecc_code[1] = ecc >> 8; + ecc_code[2] = ecc >> 16; + + pr_debug("%s: returning ecc %*phN\n", __func__, 3, ecc_code); + + return 0; +} + +static int s3c2440_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + unsigned long ecc = readl(info->regs + S3C2440_NFMECC0); + + ecc_code[0] = ecc; + ecc_code[1] = ecc >> 8; + ecc_code[2] = ecc >> 16; + + pr_debug("%s: returning ecc %06lx\n", __func__, ecc & 0xffffff); + + return 0; +} +#endif + +/* over-ride the standard functions for a little more speed. We can + * use read/write block to move the data buffers to/from the controller +*/ + +static void s3c2410_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct nand_chip *this = mtd->priv; + readsb(this->IO_ADDR_R, buf, len); +} + +static void s3c2440_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + + readsl(info->regs + S3C2440_NFDATA, buf, len >> 2); + + /* cleanup if we've got less than a word to do */ + if (len & 3) { + buf += len & ~3; + + for (; len & 3; len--) + *buf++ = readb(info->regs + S3C2440_NFDATA); + } +} + +static void s3c2410_nand_write_buf(struct mtd_info *mtd, const u_char *buf, + int len) +{ + struct nand_chip *this = mtd->priv; + writesb(this->IO_ADDR_W, buf, len); +} + +static void s3c2440_nand_write_buf(struct mtd_info *mtd, const u_char *buf, + int len) +{ + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); + + writesl(info->regs + S3C2440_NFDATA, buf, len >> 2); + + /* cleanup any fractional write */ + if (len & 3) { + buf += len & ~3; + + for (; len & 3; len--, buf++) + writeb(*buf, info->regs + S3C2440_NFDATA); + } +} + +/* cpufreq driver support */ + +#ifdef CONFIG_CPU_FREQ + +static int s3c2410_nand_cpufreq_transition(struct notifier_block *nb, + unsigned long val, void *data) +{ + struct s3c2410_nand_info *info; + unsigned long newclk; + + info = container_of(nb, struct s3c2410_nand_info, freq_transition); + newclk = clk_get_rate(info->clk); + + if ((val == CPUFREQ_POSTCHANGE && newclk < info->clk_rate) || + (val == CPUFREQ_PRECHANGE && newclk > info->clk_rate)) { + s3c2410_nand_setrate(info); + } + + return 0; +} + +static inline int s3c2410_nand_cpufreq_register(struct s3c2410_nand_info *info) +{ + info->freq_transition.notifier_call = s3c2410_nand_cpufreq_transition; + + return cpufreq_register_notifier(&info->freq_transition, + CPUFREQ_TRANSITION_NOTIFIER); +} + +static inline void +s3c2410_nand_cpufreq_deregister(struct s3c2410_nand_info *info) +{ + cpufreq_unregister_notifier(&info->freq_transition, + CPUFREQ_TRANSITION_NOTIFIER); +} + +#else +static inline int s3c2410_nand_cpufreq_register(struct s3c2410_nand_info *info) +{ + return 0; +} + +static inline void +s3c2410_nand_cpufreq_deregister(struct s3c2410_nand_info *info) +{ +} +#endif + +/* device management functions */ + +static int s3c24xx_nand_remove(struct platform_device *pdev) +{ + struct s3c2410_nand_info *info = to_nand_info(pdev); + + if (info == NULL) + return 0; + + s3c2410_nand_cpufreq_deregister(info); + + /* Release all our mtds and their partitions, then go through + * freeing the resources used + */ + + if (info->mtds != NULL) { + struct s3c2410_nand_mtd *ptr = info->mtds; + int mtdno; + + for (mtdno = 0; mtdno < info->mtd_count; mtdno++, ptr++) { + pr_debug("releasing mtd %d (%p)\n", mtdno, ptr); + nand_release(&ptr->mtd); + } + } + + /* free the common resources */ + + if (!IS_ERR(info->clk)) + s3c2410_nand_clk_set_state(info, CLOCK_DISABLE); + + return 0; +} + +static int s3c2410_nand_add_partition(struct s3c2410_nand_info *info, + struct s3c2410_nand_mtd *mtd, + struct s3c2410_nand_set *set) +{ + if (set) { + mtd->mtd.name = set->name; + + return mtd_device_parse_register(&mtd->mtd, NULL, NULL, + set->partitions, set->nr_partitions); + } + + return -ENODEV; +} + +/** + * s3c2410_nand_init_chip - initialise a single instance of an chip + * @info: The base NAND controller the chip is on. + * @nmtd: The new controller MTD instance to fill in. + * @set: The information passed from the board specific platform data. + * + * Initialise the given @nmtd from the information in @info and @set. This + * readies the structure for use with the MTD layer functions by ensuring + * all pointers are setup and the necessary control routines selected. + */ +static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info, + struct s3c2410_nand_mtd *nmtd, + struct s3c2410_nand_set *set) +{ + struct nand_chip *chip = &nmtd->chip; + void __iomem *regs = info->regs; + + chip->write_buf = s3c2410_nand_write_buf; + chip->read_buf = s3c2410_nand_read_buf; + chip->select_chip = s3c2410_nand_select_chip; + chip->chip_delay = 50; + chip->priv = nmtd; + chip->options = set->options; + chip->controller = &info->controller; + + switch (info->cpu_type) { + case TYPE_S3C2410: + chip->IO_ADDR_W = regs + S3C2410_NFDATA; + info->sel_reg = regs + S3C2410_NFCONF; + info->sel_bit = S3C2410_NFCONF_nFCE; + chip->cmd_ctrl = s3c2410_nand_hwcontrol; + chip->dev_ready = s3c2410_nand_devready; + break; + + case TYPE_S3C2440: + chip->IO_ADDR_W = regs + S3C2440_NFDATA; + info->sel_reg = regs + S3C2440_NFCONT; + info->sel_bit = S3C2440_NFCONT_nFCE; + chip->cmd_ctrl = s3c2440_nand_hwcontrol; + chip->dev_ready = s3c2440_nand_devready; + chip->read_buf = s3c2440_nand_read_buf; + chip->write_buf = s3c2440_nand_write_buf; + break; + + case TYPE_S3C2412: + chip->IO_ADDR_W = regs + S3C2440_NFDATA; + info->sel_reg = regs + S3C2440_NFCONT; + info->sel_bit = S3C2412_NFCONT_nFCE0; + chip->cmd_ctrl = s3c2440_nand_hwcontrol; + chip->dev_ready = s3c2412_nand_devready; + + if (readl(regs + S3C2410_NFCONF) & S3C2412_NFCONF_NANDBOOT) + dev_info(info->device, "System booted from NAND\n"); + + break; + } + + chip->IO_ADDR_R = chip->IO_ADDR_W; + + nmtd->info = info; + nmtd->mtd.priv = chip; + nmtd->mtd.owner = THIS_MODULE; + nmtd->set = set; + +#ifdef CONFIG_MTD_NAND_S3C2410_HWECC + chip->ecc.calculate = s3c2410_nand_calculate_ecc; + chip->ecc.correct = s3c2410_nand_correct_data; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.strength = 1; + + switch (info->cpu_type) { + case TYPE_S3C2410: + chip->ecc.hwctl = s3c2410_nand_enable_hwecc; + chip->ecc.calculate = s3c2410_nand_calculate_ecc; + break; + + case TYPE_S3C2412: + chip->ecc.hwctl = s3c2412_nand_enable_hwecc; + chip->ecc.calculate = s3c2412_nand_calculate_ecc; + break; + + case TYPE_S3C2440: + chip->ecc.hwctl = s3c2440_nand_enable_hwecc; + chip->ecc.calculate = s3c2440_nand_calculate_ecc; + break; + } +#else + chip->ecc.mode = NAND_ECC_SOFT; +#endif + + if (set->ecc_layout != NULL) + chip->ecc.layout = set->ecc_layout; + + if (set->disable_ecc) + chip->ecc.mode = NAND_ECC_NONE; + + switch (chip->ecc.mode) { + case NAND_ECC_NONE: + dev_info(info->device, "NAND ECC disabled\n"); + break; + case NAND_ECC_SOFT: + dev_info(info->device, "NAND soft ECC\n"); + break; + case NAND_ECC_HW: + dev_info(info->device, "NAND hardware ECC\n"); + break; + default: + dev_info(info->device, "NAND ECC UNKNOWN\n"); + break; + } + + /* If you use u-boot BBT creation code, specifying this flag will + * let the kernel fish out the BBT from the NAND, and also skip the + * full NAND scan that can take 1/2s or so. Little things... */ + if (set->flash_bbt) { + chip->bbt_options |= NAND_BBT_USE_FLASH; + chip->options |= NAND_SKIP_BBTSCAN; + } +} + +/** + * s3c2410_nand_update_chip - post probe update + * @info: The controller instance. + * @nmtd: The driver version of the MTD instance. + * + * This routine is called after the chip probe has successfully completed + * and the relevant per-chip information updated. This call ensure that + * we update the internal state accordingly. + * + * The internal state is currently limited to the ECC state information. +*/ +static void s3c2410_nand_update_chip(struct s3c2410_nand_info *info, + struct s3c2410_nand_mtd *nmtd) +{ + struct nand_chip *chip = &nmtd->chip; + + dev_dbg(info->device, "chip %p => page shift %d\n", + chip, chip->page_shift); + + if (chip->ecc.mode != NAND_ECC_HW) + return; + + /* change the behaviour depending on whether we are using + * the large or small page nand device */ + + if (chip->page_shift > 10) { + chip->ecc.size = 256; + chip->ecc.bytes = 3; + } else { + chip->ecc.size = 512; + chip->ecc.bytes = 3; + chip->ecc.layout = &nand_hw_eccoob; + } +} + +/* s3c24xx_nand_probe + * + * called by device layer when it finds a device matching + * one our driver can handled. This code checks to see if + * it can allocate all necessary resources then calls the + * nand layer to look for devices +*/ +static int s3c24xx_nand_probe(struct platform_device *pdev) +{ + struct s3c2410_platform_nand *plat = to_nand_plat(pdev); + enum s3c_cpu_type cpu_type; + struct s3c2410_nand_info *info; + struct s3c2410_nand_mtd *nmtd; + struct s3c2410_nand_set *sets; + struct resource *res; + int err = 0; + int size; + int nr_sets; + int setno; + + cpu_type = platform_get_device_id(pdev)->driver_data; + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (info == NULL) { + err = -ENOMEM; + goto exit_error; + } + + platform_set_drvdata(pdev, info); + + spin_lock_init(&info->controller.lock); + init_waitqueue_head(&info->controller.wq); + + /* get the clock source and enable it */ + + info->clk = devm_clk_get(&pdev->dev, "nand"); + if (IS_ERR(info->clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + err = -ENOENT; + goto exit_error; + } + + s3c2410_nand_clk_set_state(info, CLOCK_ENABLE); + + /* allocate and map the resource */ + + /* currently we assume we have the one resource */ + res = pdev->resource; + size = resource_size(res); + + info->device = &pdev->dev; + info->platform = plat; + info->cpu_type = cpu_type; + + info->regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(info->regs)) { + err = PTR_ERR(info->regs); + goto exit_error; + } + + dev_dbg(&pdev->dev, "mapped registers at %p\n", info->regs); + + /* initialise the hardware */ + + err = s3c2410_nand_inithw(info); + if (err != 0) + goto exit_error; + + sets = (plat != NULL) ? plat->sets : NULL; + nr_sets = (plat != NULL) ? plat->nr_sets : 1; + + info->mtd_count = nr_sets; + + /* allocate our information */ + + size = nr_sets * sizeof(*info->mtds); + info->mtds = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); + if (info->mtds == NULL) { + err = -ENOMEM; + goto exit_error; + } + + /* initialise all possible chips */ + + nmtd = info->mtds; + + for (setno = 0; setno < nr_sets; setno++, nmtd++) { + pr_debug("initialising set %d (%p, info %p)\n", + setno, nmtd, info); + + s3c2410_nand_init_chip(info, nmtd, sets); + + nmtd->scan_res = nand_scan_ident(&nmtd->mtd, + (sets) ? sets->nr_chips : 1, + NULL); + + if (nmtd->scan_res == 0) { + s3c2410_nand_update_chip(info, nmtd); + nand_scan_tail(&nmtd->mtd); + s3c2410_nand_add_partition(info, nmtd, sets); + } + + if (sets != NULL) + sets++; + } + + err = s3c2410_nand_cpufreq_register(info); + if (err < 0) { + dev_err(&pdev->dev, "failed to init cpufreq support\n"); + goto exit_error; + } + + if (allow_clk_suspend(info)) { + dev_info(&pdev->dev, "clock idle support enabled\n"); + s3c2410_nand_clk_set_state(info, CLOCK_SUSPEND); + } + + return 0; + + exit_error: + s3c24xx_nand_remove(pdev); + + if (err == 0) + err = -EINVAL; + return err; +} + +/* PM Support */ +#ifdef CONFIG_PM + +static int s3c24xx_nand_suspend(struct platform_device *dev, pm_message_t pm) +{ + struct s3c2410_nand_info *info = platform_get_drvdata(dev); + + if (info) { + info->save_sel = readl(info->sel_reg); + + /* For the moment, we must ensure nFCE is high during + * the time we are suspended. This really should be + * handled by suspending the MTDs we are using, but + * that is currently not the case. */ + + writel(info->save_sel | info->sel_bit, info->sel_reg); + + s3c2410_nand_clk_set_state(info, CLOCK_DISABLE); + } + + return 0; +} + +static int s3c24xx_nand_resume(struct platform_device *dev) +{ + struct s3c2410_nand_info *info = platform_get_drvdata(dev); + unsigned long sel; + + if (info) { + s3c2410_nand_clk_set_state(info, CLOCK_ENABLE); + s3c2410_nand_inithw(info); + + /* Restore the state of the nFCE line. */ + + sel = readl(info->sel_reg); + sel &= ~info->sel_bit; + sel |= info->save_sel & info->sel_bit; + writel(sel, info->sel_reg); + + s3c2410_nand_clk_set_state(info, CLOCK_SUSPEND); + } + + return 0; +} + +#else +#define s3c24xx_nand_suspend NULL +#define s3c24xx_nand_resume NULL +#endif + +/* driver device registration */ + +static struct platform_device_id s3c24xx_driver_ids[] = { + { + .name = "s3c2410-nand", + .driver_data = TYPE_S3C2410, + }, { + .name = "s3c2440-nand", + .driver_data = TYPE_S3C2440, + }, { + .name = "s3c2412-nand", + .driver_data = TYPE_S3C2412, + }, { + .name = "s3c6400-nand", + .driver_data = TYPE_S3C2412, /* compatible with 2412 */ + }, + { } +}; + +MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids); + +static struct platform_driver s3c24xx_nand_driver = { + .probe = s3c24xx_nand_probe, + .remove = s3c24xx_nand_remove, + .suspend = s3c24xx_nand_suspend, + .resume = s3c24xx_nand_resume, + .id_table = s3c24xx_driver_ids, + .driver = { + .name = "s3c24xx-nand", + }, +}; + +module_platform_driver(s3c24xx_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_DESCRIPTION("S3C24XX MTD NAND driver"); diff --git a/drivers/mtd/nand/sh_flctl.c b/drivers/mtd/nand/sh_flctl.c new file mode 100644 index 000000000..c3ce81c1a --- /dev/null +++ b/drivers/mtd/nand/sh_flctl.c @@ -0,0 +1,1200 @@ +/* + * SuperH FLCTL nand controller + * + * Copyright (c) 2008 Renesas Solutions Corp. + * Copyright (c) 2008 Atom Create Engineering Co., Ltd. + * + * Based on fsl_elbc_nand.c, Copyright (c) 2006-2007 Freescale Semiconductor + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + * + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_mtd.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/sh_dma.h> +#include <linux/slab.h> +#include <linux/string.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/sh_flctl.h> + +static struct nand_ecclayout flctl_4secc_oob_16 = { + .eccbytes = 10, + .eccpos = {0, 1, 2, 3, 4, 5, 6, 7, 8, 9}, + .oobfree = { + {.offset = 12, + . length = 4} }, +}; + +static struct nand_ecclayout flctl_4secc_oob_64 = { + .eccbytes = 4 * 10, + .eccpos = { + 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, + 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, + 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }, + .oobfree = { + {.offset = 2, .length = 4}, + {.offset = 16, .length = 6}, + {.offset = 32, .length = 6}, + {.offset = 48, .length = 6} }, +}; + +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +static struct nand_bbt_descr flctl_4secc_smallpage = { + .options = NAND_BBT_SCAN2NDPAGE, + .offs = 11, + .len = 1, + .pattern = scan_ff_pattern, +}; + +static struct nand_bbt_descr flctl_4secc_largepage = { + .options = NAND_BBT_SCAN2NDPAGE, + .offs = 0, + .len = 2, + .pattern = scan_ff_pattern, +}; + +static void empty_fifo(struct sh_flctl *flctl) +{ + writel(flctl->flintdmacr_base | AC1CLR | AC0CLR, FLINTDMACR(flctl)); + writel(flctl->flintdmacr_base, FLINTDMACR(flctl)); +} + +static void start_translation(struct sh_flctl *flctl) +{ + writeb(TRSTRT, FLTRCR(flctl)); +} + +static void timeout_error(struct sh_flctl *flctl, const char *str) +{ + dev_err(&flctl->pdev->dev, "Timeout occurred in %s\n", str); +} + +static void wait_completion(struct sh_flctl *flctl) +{ + uint32_t timeout = LOOP_TIMEOUT_MAX; + + while (timeout--) { + if (readb(FLTRCR(flctl)) & TREND) { + writeb(0x0, FLTRCR(flctl)); + return; + } + udelay(1); + } + + timeout_error(flctl, __func__); + writeb(0x0, FLTRCR(flctl)); +} + +static void flctl_dma_complete(void *param) +{ + struct sh_flctl *flctl = param; + + complete(&flctl->dma_complete); +} + +static void flctl_release_dma(struct sh_flctl *flctl) +{ + if (flctl->chan_fifo0_rx) { + dma_release_channel(flctl->chan_fifo0_rx); + flctl->chan_fifo0_rx = NULL; + } + if (flctl->chan_fifo0_tx) { + dma_release_channel(flctl->chan_fifo0_tx); + flctl->chan_fifo0_tx = NULL; + } +} + +static void flctl_setup_dma(struct sh_flctl *flctl) +{ + dma_cap_mask_t mask; + struct dma_slave_config cfg; + struct platform_device *pdev = flctl->pdev; + struct sh_flctl_platform_data *pdata = dev_get_platdata(&pdev->dev); + int ret; + + if (!pdata) + return; + + if (pdata->slave_id_fifo0_tx <= 0 || pdata->slave_id_fifo0_rx <= 0) + return; + + /* We can only either use DMA for both Tx and Rx or not use it at all */ + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + + flctl->chan_fifo0_tx = dma_request_channel(mask, shdma_chan_filter, + (void *)(uintptr_t)pdata->slave_id_fifo0_tx); + dev_dbg(&pdev->dev, "%s: TX: got channel %p\n", __func__, + flctl->chan_fifo0_tx); + + if (!flctl->chan_fifo0_tx) + return; + + memset(&cfg, 0, sizeof(cfg)); + cfg.direction = DMA_MEM_TO_DEV; + cfg.dst_addr = (dma_addr_t)FLDTFIFO(flctl); + cfg.src_addr = 0; + ret = dmaengine_slave_config(flctl->chan_fifo0_tx, &cfg); + if (ret < 0) + goto err; + + flctl->chan_fifo0_rx = dma_request_channel(mask, shdma_chan_filter, + (void *)(uintptr_t)pdata->slave_id_fifo0_rx); + dev_dbg(&pdev->dev, "%s: RX: got channel %p\n", __func__, + flctl->chan_fifo0_rx); + + if (!flctl->chan_fifo0_rx) + goto err; + + cfg.direction = DMA_DEV_TO_MEM; + cfg.dst_addr = 0; + cfg.src_addr = (dma_addr_t)FLDTFIFO(flctl); + ret = dmaengine_slave_config(flctl->chan_fifo0_rx, &cfg); + if (ret < 0) + goto err; + + init_completion(&flctl->dma_complete); + + return; + +err: + flctl_release_dma(flctl); +} + +static void set_addr(struct mtd_info *mtd, int column, int page_addr) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + uint32_t addr = 0; + + if (column == -1) { + addr = page_addr; /* ERASE1 */ + } else if (page_addr != -1) { + /* SEQIN, READ0, etc.. */ + if (flctl->chip.options & NAND_BUSWIDTH_16) + column >>= 1; + if (flctl->page_size) { + addr = column & 0x0FFF; + addr |= (page_addr & 0xff) << 16; + addr |= ((page_addr >> 8) & 0xff) << 24; + /* big than 128MB */ + if (flctl->rw_ADRCNT == ADRCNT2_E) { + uint32_t addr2; + addr2 = (page_addr >> 16) & 0xff; + writel(addr2, FLADR2(flctl)); + } + } else { + addr = column; + addr |= (page_addr & 0xff) << 8; + addr |= ((page_addr >> 8) & 0xff) << 16; + addr |= ((page_addr >> 16) & 0xff) << 24; + } + } + writel(addr, FLADR(flctl)); +} + +static void wait_rfifo_ready(struct sh_flctl *flctl) +{ + uint32_t timeout = LOOP_TIMEOUT_MAX; + + while (timeout--) { + uint32_t val; + /* check FIFO */ + val = readl(FLDTCNTR(flctl)) >> 16; + if (val & 0xFF) + return; + udelay(1); + } + timeout_error(flctl, __func__); +} + +static void wait_wfifo_ready(struct sh_flctl *flctl) +{ + uint32_t len, timeout = LOOP_TIMEOUT_MAX; + + while (timeout--) { + /* check FIFO */ + len = (readl(FLDTCNTR(flctl)) >> 16) & 0xFF; + if (len >= 4) + return; + udelay(1); + } + timeout_error(flctl, __func__); +} + +static enum flctl_ecc_res_t wait_recfifo_ready + (struct sh_flctl *flctl, int sector_number) +{ + uint32_t timeout = LOOP_TIMEOUT_MAX; + void __iomem *ecc_reg[4]; + int i; + int state = FL_SUCCESS; + uint32_t data, size; + + /* + * First this loops checks in FLDTCNTR if we are ready to read out the + * oob data. This is the case if either all went fine without errors or + * if the bottom part of the loop corrected the errors or marked them as + * uncorrectable and the controller is given time to push the data into + * the FIFO. + */ + while (timeout--) { + /* check if all is ok and we can read out the OOB */ + size = readl(FLDTCNTR(flctl)) >> 24; + if ((size & 0xFF) == 4) + return state; + + /* check if a correction code has been calculated */ + if (!(readl(FL4ECCCR(flctl)) & _4ECCEND)) { + /* + * either we wait for the fifo to be filled or a + * correction pattern is being generated + */ + udelay(1); + continue; + } + + /* check for an uncorrectable error */ + if (readl(FL4ECCCR(flctl)) & _4ECCFA) { + /* check if we face a non-empty page */ + for (i = 0; i < 512; i++) { + if (flctl->done_buff[i] != 0xff) { + state = FL_ERROR; /* can't correct */ + break; + } + } + + if (state == FL_SUCCESS) + dev_dbg(&flctl->pdev->dev, + "reading empty sector %d, ecc error ignored\n", + sector_number); + + writel(0, FL4ECCCR(flctl)); + continue; + } + + /* start error correction */ + ecc_reg[0] = FL4ECCRESULT0(flctl); + ecc_reg[1] = FL4ECCRESULT1(flctl); + ecc_reg[2] = FL4ECCRESULT2(flctl); + ecc_reg[3] = FL4ECCRESULT3(flctl); + + for (i = 0; i < 3; i++) { + uint8_t org; + unsigned int index; + + data = readl(ecc_reg[i]); + + if (flctl->page_size) + index = (512 * sector_number) + + (data >> 16); + else + index = data >> 16; + + org = flctl->done_buff[index]; + flctl->done_buff[index] = org ^ (data & 0xFF); + } + state = FL_REPAIRABLE; + writel(0, FL4ECCCR(flctl)); + } + + timeout_error(flctl, __func__); + return FL_TIMEOUT; /* timeout */ +} + +static void wait_wecfifo_ready(struct sh_flctl *flctl) +{ + uint32_t timeout = LOOP_TIMEOUT_MAX; + uint32_t len; + + while (timeout--) { + /* check FLECFIFO */ + len = (readl(FLDTCNTR(flctl)) >> 24) & 0xFF; + if (len >= 4) + return; + udelay(1); + } + timeout_error(flctl, __func__); +} + +static int flctl_dma_fifo0_transfer(struct sh_flctl *flctl, unsigned long *buf, + int len, enum dma_data_direction dir) +{ + struct dma_async_tx_descriptor *desc = NULL; + struct dma_chan *chan; + enum dma_transfer_direction tr_dir; + dma_addr_t dma_addr; + dma_cookie_t cookie = -EINVAL; + uint32_t reg; + int ret; + + if (dir == DMA_FROM_DEVICE) { + chan = flctl->chan_fifo0_rx; + tr_dir = DMA_DEV_TO_MEM; + } else { + chan = flctl->chan_fifo0_tx; + tr_dir = DMA_MEM_TO_DEV; + } + + dma_addr = dma_map_single(chan->device->dev, buf, len, dir); + + if (dma_addr) + desc = dmaengine_prep_slave_single(chan, dma_addr, len, + tr_dir, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + + if (desc) { + reg = readl(FLINTDMACR(flctl)); + reg |= DREQ0EN; + writel(reg, FLINTDMACR(flctl)); + + desc->callback = flctl_dma_complete; + desc->callback_param = flctl; + cookie = dmaengine_submit(desc); + + dma_async_issue_pending(chan); + } else { + /* DMA failed, fall back to PIO */ + flctl_release_dma(flctl); + dev_warn(&flctl->pdev->dev, + "DMA failed, falling back to PIO\n"); + ret = -EIO; + goto out; + } + + ret = + wait_for_completion_timeout(&flctl->dma_complete, + msecs_to_jiffies(3000)); + + if (ret <= 0) { + dmaengine_terminate_all(chan); + dev_err(&flctl->pdev->dev, "wait_for_completion_timeout\n"); + } + +out: + reg = readl(FLINTDMACR(flctl)); + reg &= ~DREQ0EN; + writel(reg, FLINTDMACR(flctl)); + + dma_unmap_single(chan->device->dev, dma_addr, len, dir); + + /* ret > 0 is success */ + return ret; +} + +static void read_datareg(struct sh_flctl *flctl, int offset) +{ + unsigned long data; + unsigned long *buf = (unsigned long *)&flctl->done_buff[offset]; + + wait_completion(flctl); + + data = readl(FLDATAR(flctl)); + *buf = le32_to_cpu(data); +} + +static void read_fiforeg(struct sh_flctl *flctl, int rlen, int offset) +{ + int i, len_4align; + unsigned long *buf = (unsigned long *)&flctl->done_buff[offset]; + + len_4align = (rlen + 3) / 4; + + /* initiate DMA transfer */ + if (flctl->chan_fifo0_rx && rlen >= 32 && + flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0) + goto convert; /* DMA success */ + + /* do polling transfer */ + for (i = 0; i < len_4align; i++) { + wait_rfifo_ready(flctl); + buf[i] = readl(FLDTFIFO(flctl)); + } + +convert: + for (i = 0; i < len_4align; i++) + buf[i] = be32_to_cpu(buf[i]); +} + +static enum flctl_ecc_res_t read_ecfiforeg + (struct sh_flctl *flctl, uint8_t *buff, int sector) +{ + int i; + enum flctl_ecc_res_t res; + unsigned long *ecc_buf = (unsigned long *)buff; + + res = wait_recfifo_ready(flctl , sector); + + if (res != FL_ERROR) { + for (i = 0; i < 4; i++) { + ecc_buf[i] = readl(FLECFIFO(flctl)); + ecc_buf[i] = be32_to_cpu(ecc_buf[i]); + } + } + + return res; +} + +static void write_fiforeg(struct sh_flctl *flctl, int rlen, + unsigned int offset) +{ + int i, len_4align; + unsigned long *buf = (unsigned long *)&flctl->done_buff[offset]; + + len_4align = (rlen + 3) / 4; + for (i = 0; i < len_4align; i++) { + wait_wfifo_ready(flctl); + writel(cpu_to_be32(buf[i]), FLDTFIFO(flctl)); + } +} + +static void write_ec_fiforeg(struct sh_flctl *flctl, int rlen, + unsigned int offset) +{ + int i, len_4align; + unsigned long *buf = (unsigned long *)&flctl->done_buff[offset]; + + len_4align = (rlen + 3) / 4; + + for (i = 0; i < len_4align; i++) + buf[i] = cpu_to_be32(buf[i]); + + /* initiate DMA transfer */ + if (flctl->chan_fifo0_tx && rlen >= 32 && + flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0) + return; /* DMA success */ + + /* do polling transfer */ + for (i = 0; i < len_4align; i++) { + wait_wecfifo_ready(flctl); + writel(buf[i], FLECFIFO(flctl)); + } +} + +static void set_cmd_regs(struct mtd_info *mtd, uint32_t cmd, uint32_t flcmcdr_val) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + uint32_t flcmncr_val = flctl->flcmncr_base & ~SEL_16BIT; + uint32_t flcmdcr_val, addr_len_bytes = 0; + + /* Set SNAND bit if page size is 2048byte */ + if (flctl->page_size) + flcmncr_val |= SNAND_E; + else + flcmncr_val &= ~SNAND_E; + + /* default FLCMDCR val */ + flcmdcr_val = DOCMD1_E | DOADR_E; + + /* Set for FLCMDCR */ + switch (cmd) { + case NAND_CMD_ERASE1: + addr_len_bytes = flctl->erase_ADRCNT; + flcmdcr_val |= DOCMD2_E; + break; + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + case NAND_CMD_RNDOUT: + addr_len_bytes = flctl->rw_ADRCNT; + flcmdcr_val |= CDSRC_E; + if (flctl->chip.options & NAND_BUSWIDTH_16) + flcmncr_val |= SEL_16BIT; + break; + case NAND_CMD_SEQIN: + /* This case is that cmd is READ0 or READ1 or READ00 */ + flcmdcr_val &= ~DOADR_E; /* ONLY execute 1st cmd */ + break; + case NAND_CMD_PAGEPROG: + addr_len_bytes = flctl->rw_ADRCNT; + flcmdcr_val |= DOCMD2_E | CDSRC_E | SELRW; + if (flctl->chip.options & NAND_BUSWIDTH_16) + flcmncr_val |= SEL_16BIT; + break; + case NAND_CMD_READID: + flcmncr_val &= ~SNAND_E; + flcmdcr_val |= CDSRC_E; + addr_len_bytes = ADRCNT_1; + break; + case NAND_CMD_STATUS: + case NAND_CMD_RESET: + flcmncr_val &= ~SNAND_E; + flcmdcr_val &= ~(DOADR_E | DOSR_E); + break; + default: + break; + } + + /* Set address bytes parameter */ + flcmdcr_val |= addr_len_bytes; + + /* Now actually write */ + writel(flcmncr_val, FLCMNCR(flctl)); + writel(flcmdcr_val, FLCMDCR(flctl)); + writel(flcmcdr_val, FLCMCDR(flctl)); +} + +static int flctl_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + chip->read_buf(mtd, buf, mtd->writesize); + if (oob_required) + chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +static int flctl_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + chip->write_buf(mtd, buf, mtd->writesize); + chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + return 0; +} + +static void execmd_read_page_sector(struct mtd_info *mtd, int page_addr) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + int sector, page_sectors; + enum flctl_ecc_res_t ecc_result; + + page_sectors = flctl->page_size ? 4 : 1; + + set_cmd_regs(mtd, NAND_CMD_READ0, + (NAND_CMD_READSTART << 8) | NAND_CMD_READ0); + + writel(readl(FLCMNCR(flctl)) | ACM_SACCES_MODE | _4ECCCORRECT, + FLCMNCR(flctl)); + writel(readl(FLCMDCR(flctl)) | page_sectors, FLCMDCR(flctl)); + writel(page_addr << 2, FLADR(flctl)); + + empty_fifo(flctl); + start_translation(flctl); + + for (sector = 0; sector < page_sectors; sector++) { + read_fiforeg(flctl, 512, 512 * sector); + + ecc_result = read_ecfiforeg(flctl, + &flctl->done_buff[mtd->writesize + 16 * sector], + sector); + + switch (ecc_result) { + case FL_REPAIRABLE: + dev_info(&flctl->pdev->dev, + "applied ecc on page 0x%x", page_addr); + flctl->mtd.ecc_stats.corrected++; + break; + case FL_ERROR: + dev_warn(&flctl->pdev->dev, + "page 0x%x contains corrupted data\n", + page_addr); + flctl->mtd.ecc_stats.failed++; + break; + default: + ; + } + } + + wait_completion(flctl); + + writel(readl(FLCMNCR(flctl)) & ~(ACM_SACCES_MODE | _4ECCCORRECT), + FLCMNCR(flctl)); +} + +static void execmd_read_oob(struct mtd_info *mtd, int page_addr) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + int page_sectors = flctl->page_size ? 4 : 1; + int i; + + set_cmd_regs(mtd, NAND_CMD_READ0, + (NAND_CMD_READSTART << 8) | NAND_CMD_READ0); + + empty_fifo(flctl); + + for (i = 0; i < page_sectors; i++) { + set_addr(mtd, (512 + 16) * i + 512 , page_addr); + writel(16, FLDTCNTR(flctl)); + + start_translation(flctl); + read_fiforeg(flctl, 16, 16 * i); + wait_completion(flctl); + } +} + +static void execmd_write_page_sector(struct mtd_info *mtd) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + int page_addr = flctl->seqin_page_addr; + int sector, page_sectors; + + page_sectors = flctl->page_size ? 4 : 1; + + set_cmd_regs(mtd, NAND_CMD_PAGEPROG, + (NAND_CMD_PAGEPROG << 8) | NAND_CMD_SEQIN); + + empty_fifo(flctl); + writel(readl(FLCMNCR(flctl)) | ACM_SACCES_MODE, FLCMNCR(flctl)); + writel(readl(FLCMDCR(flctl)) | page_sectors, FLCMDCR(flctl)); + writel(page_addr << 2, FLADR(flctl)); + start_translation(flctl); + + for (sector = 0; sector < page_sectors; sector++) { + write_fiforeg(flctl, 512, 512 * sector); + write_ec_fiforeg(flctl, 16, mtd->writesize + 16 * sector); + } + + wait_completion(flctl); + writel(readl(FLCMNCR(flctl)) & ~ACM_SACCES_MODE, FLCMNCR(flctl)); +} + +static void execmd_write_oob(struct mtd_info *mtd) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + int page_addr = flctl->seqin_page_addr; + int sector, page_sectors; + + page_sectors = flctl->page_size ? 4 : 1; + + set_cmd_regs(mtd, NAND_CMD_PAGEPROG, + (NAND_CMD_PAGEPROG << 8) | NAND_CMD_SEQIN); + + for (sector = 0; sector < page_sectors; sector++) { + empty_fifo(flctl); + set_addr(mtd, sector * 528 + 512, page_addr); + writel(16, FLDTCNTR(flctl)); /* set read size */ + + start_translation(flctl); + write_fiforeg(flctl, 16, 16 * sector); + wait_completion(flctl); + } +} + +static void flctl_cmdfunc(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + uint32_t read_cmd = 0; + + pm_runtime_get_sync(&flctl->pdev->dev); + + flctl->read_bytes = 0; + if (command != NAND_CMD_PAGEPROG) + flctl->index = 0; + + switch (command) { + case NAND_CMD_READ1: + case NAND_CMD_READ0: + if (flctl->hwecc) { + /* read page with hwecc */ + execmd_read_page_sector(mtd, page_addr); + break; + } + if (flctl->page_size) + set_cmd_regs(mtd, command, (NAND_CMD_READSTART << 8) + | command); + else + set_cmd_regs(mtd, command, command); + + set_addr(mtd, 0, page_addr); + + flctl->read_bytes = mtd->writesize + mtd->oobsize; + if (flctl->chip.options & NAND_BUSWIDTH_16) + column >>= 1; + flctl->index += column; + goto read_normal_exit; + + case NAND_CMD_READOOB: + if (flctl->hwecc) { + /* read page with hwecc */ + execmd_read_oob(mtd, page_addr); + break; + } + + if (flctl->page_size) { + set_cmd_regs(mtd, command, (NAND_CMD_READSTART << 8) + | NAND_CMD_READ0); + set_addr(mtd, mtd->writesize, page_addr); + } else { + set_cmd_regs(mtd, command, command); + set_addr(mtd, 0, page_addr); + } + flctl->read_bytes = mtd->oobsize; + goto read_normal_exit; + + case NAND_CMD_RNDOUT: + if (flctl->hwecc) + break; + + if (flctl->page_size) + set_cmd_regs(mtd, command, (NAND_CMD_RNDOUTSTART << 8) + | command); + else + set_cmd_regs(mtd, command, command); + + set_addr(mtd, column, 0); + + flctl->read_bytes = mtd->writesize + mtd->oobsize - column; + goto read_normal_exit; + + case NAND_CMD_READID: + set_cmd_regs(mtd, command, command); + + /* READID is always performed using an 8-bit bus */ + if (flctl->chip.options & NAND_BUSWIDTH_16) + column <<= 1; + set_addr(mtd, column, 0); + + flctl->read_bytes = 8; + writel(flctl->read_bytes, FLDTCNTR(flctl)); /* set read size */ + empty_fifo(flctl); + start_translation(flctl); + read_fiforeg(flctl, flctl->read_bytes, 0); + wait_completion(flctl); + break; + + case NAND_CMD_ERASE1: + flctl->erase1_page_addr = page_addr; + break; + + case NAND_CMD_ERASE2: + set_cmd_regs(mtd, NAND_CMD_ERASE1, + (command << 8) | NAND_CMD_ERASE1); + set_addr(mtd, -1, flctl->erase1_page_addr); + start_translation(flctl); + wait_completion(flctl); + break; + + case NAND_CMD_SEQIN: + if (!flctl->page_size) { + /* output read command */ + if (column >= mtd->writesize) { + column -= mtd->writesize; + read_cmd = NAND_CMD_READOOB; + } else if (column < 256) { + read_cmd = NAND_CMD_READ0; + } else { + column -= 256; + read_cmd = NAND_CMD_READ1; + } + } + flctl->seqin_column = column; + flctl->seqin_page_addr = page_addr; + flctl->seqin_read_cmd = read_cmd; + break; + + case NAND_CMD_PAGEPROG: + empty_fifo(flctl); + if (!flctl->page_size) { + set_cmd_regs(mtd, NAND_CMD_SEQIN, + flctl->seqin_read_cmd); + set_addr(mtd, -1, -1); + writel(0, FLDTCNTR(flctl)); /* set 0 size */ + start_translation(flctl); + wait_completion(flctl); + } + if (flctl->hwecc) { + /* write page with hwecc */ + if (flctl->seqin_column == mtd->writesize) + execmd_write_oob(mtd); + else if (!flctl->seqin_column) + execmd_write_page_sector(mtd); + else + printk(KERN_ERR "Invalid address !?\n"); + break; + } + set_cmd_regs(mtd, command, (command << 8) | NAND_CMD_SEQIN); + set_addr(mtd, flctl->seqin_column, flctl->seqin_page_addr); + writel(flctl->index, FLDTCNTR(flctl)); /* set write size */ + start_translation(flctl); + write_fiforeg(flctl, flctl->index, 0); + wait_completion(flctl); + break; + + case NAND_CMD_STATUS: + set_cmd_regs(mtd, command, command); + set_addr(mtd, -1, -1); + + flctl->read_bytes = 1; + writel(flctl->read_bytes, FLDTCNTR(flctl)); /* set read size */ + start_translation(flctl); + read_datareg(flctl, 0); /* read and end */ + break; + + case NAND_CMD_RESET: + set_cmd_regs(mtd, command, command); + set_addr(mtd, -1, -1); + + writel(0, FLDTCNTR(flctl)); /* set 0 size */ + start_translation(flctl); + wait_completion(flctl); + break; + + default: + break; + } + goto runtime_exit; + +read_normal_exit: + writel(flctl->read_bytes, FLDTCNTR(flctl)); /* set read size */ + empty_fifo(flctl); + start_translation(flctl); + read_fiforeg(flctl, flctl->read_bytes, 0); + wait_completion(flctl); +runtime_exit: + pm_runtime_put_sync(&flctl->pdev->dev); + return; +} + +static void flctl_select_chip(struct mtd_info *mtd, int chipnr) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + int ret; + + switch (chipnr) { + case -1: + flctl->flcmncr_base &= ~CE0_ENABLE; + + pm_runtime_get_sync(&flctl->pdev->dev); + writel(flctl->flcmncr_base, FLCMNCR(flctl)); + + if (flctl->qos_request) { + dev_pm_qos_remove_request(&flctl->pm_qos); + flctl->qos_request = 0; + } + + pm_runtime_put_sync(&flctl->pdev->dev); + break; + case 0: + flctl->flcmncr_base |= CE0_ENABLE; + + if (!flctl->qos_request) { + ret = dev_pm_qos_add_request(&flctl->pdev->dev, + &flctl->pm_qos, + DEV_PM_QOS_RESUME_LATENCY, + 100); + if (ret < 0) + dev_err(&flctl->pdev->dev, + "PM QoS request failed: %d\n", ret); + flctl->qos_request = 1; + } + + if (flctl->holden) { + pm_runtime_get_sync(&flctl->pdev->dev); + writel(HOLDEN, FLHOLDCR(flctl)); + pm_runtime_put_sync(&flctl->pdev->dev); + } + break; + default: + BUG(); + } +} + +static void flctl_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + + memcpy(&flctl->done_buff[flctl->index], buf, len); + flctl->index += len; +} + +static uint8_t flctl_read_byte(struct mtd_info *mtd) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + uint8_t data; + + data = flctl->done_buff[flctl->index]; + flctl->index++; + return data; +} + +static uint16_t flctl_read_word(struct mtd_info *mtd) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + uint16_t *buf = (uint16_t *)&flctl->done_buff[flctl->index]; + + flctl->index += 2; + return *buf; +} + +static void flctl_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + + memcpy(buf, &flctl->done_buff[flctl->index], len); + flctl->index += len; +} + +static int flctl_chip_init_tail(struct mtd_info *mtd) +{ + struct sh_flctl *flctl = mtd_to_flctl(mtd); + struct nand_chip *chip = &flctl->chip; + + if (mtd->writesize == 512) { + flctl->page_size = 0; + if (chip->chipsize > (32 << 20)) { + /* big than 32MB */ + flctl->rw_ADRCNT = ADRCNT_4; + flctl->erase_ADRCNT = ADRCNT_3; + } else if (chip->chipsize > (2 << 16)) { + /* big than 128KB */ + flctl->rw_ADRCNT = ADRCNT_3; + flctl->erase_ADRCNT = ADRCNT_2; + } else { + flctl->rw_ADRCNT = ADRCNT_2; + flctl->erase_ADRCNT = ADRCNT_1; + } + } else { + flctl->page_size = 1; + if (chip->chipsize > (128 << 20)) { + /* big than 128MB */ + flctl->rw_ADRCNT = ADRCNT2_E; + flctl->erase_ADRCNT = ADRCNT_3; + } else if (chip->chipsize > (8 << 16)) { + /* big than 512KB */ + flctl->rw_ADRCNT = ADRCNT_4; + flctl->erase_ADRCNT = ADRCNT_2; + } else { + flctl->rw_ADRCNT = ADRCNT_3; + flctl->erase_ADRCNT = ADRCNT_1; + } + } + + if (flctl->hwecc) { + if (mtd->writesize == 512) { + chip->ecc.layout = &flctl_4secc_oob_16; + chip->badblock_pattern = &flctl_4secc_smallpage; + } else { + chip->ecc.layout = &flctl_4secc_oob_64; + chip->badblock_pattern = &flctl_4secc_largepage; + } + + chip->ecc.size = 512; + chip->ecc.bytes = 10; + chip->ecc.strength = 4; + chip->ecc.read_page = flctl_read_page_hwecc; + chip->ecc.write_page = flctl_write_page_hwecc; + chip->ecc.mode = NAND_ECC_HW; + + /* 4 symbols ECC enabled */ + flctl->flcmncr_base |= _4ECCEN; + } else { + chip->ecc.mode = NAND_ECC_SOFT; + } + + return 0; +} + +static irqreturn_t flctl_handle_flste(int irq, void *dev_id) +{ + struct sh_flctl *flctl = dev_id; + + dev_err(&flctl->pdev->dev, "flste irq: %x\n", readl(FLINTDMACR(flctl))); + writel(flctl->flintdmacr_base, FLINTDMACR(flctl)); + + return IRQ_HANDLED; +} + +struct flctl_soc_config { + unsigned long flcmncr_val; + unsigned has_hwecc:1; + unsigned use_holden:1; +}; + +static struct flctl_soc_config flctl_sh7372_config = { + .flcmncr_val = CLK_16B_12L_4H | TYPESEL_SET | SHBUSSEL, + .has_hwecc = 1, + .use_holden = 1, +}; + +static const struct of_device_id of_flctl_match[] = { + { .compatible = "renesas,shmobile-flctl-sh7372", + .data = &flctl_sh7372_config }, + {}, +}; +MODULE_DEVICE_TABLE(of, of_flctl_match); + +static struct sh_flctl_platform_data *flctl_parse_dt(struct device *dev) +{ + const struct of_device_id *match; + struct flctl_soc_config *config; + struct sh_flctl_platform_data *pdata; + struct device_node *dn = dev->of_node; + int ret; + + match = of_match_device(of_flctl_match, dev); + if (match) + config = (struct flctl_soc_config *)match->data; + else { + dev_err(dev, "%s: no OF configuration attached\n", __func__); + return NULL; + } + + pdata = devm_kzalloc(dev, sizeof(struct sh_flctl_platform_data), + GFP_KERNEL); + if (!pdata) + return NULL; + + /* set SoC specific options */ + pdata->flcmncr_val = config->flcmncr_val; + pdata->has_hwecc = config->has_hwecc; + pdata->use_holden = config->use_holden; + + /* parse user defined options */ + ret = of_get_nand_bus_width(dn); + if (ret == 16) + pdata->flcmncr_val |= SEL_16BIT; + else if (ret != 8) { + dev_err(dev, "%s: invalid bus width\n", __func__); + return NULL; + } + + return pdata; +} + +static int flctl_probe(struct platform_device *pdev) +{ + struct resource *res; + struct sh_flctl *flctl; + struct mtd_info *flctl_mtd; + struct nand_chip *nand; + struct sh_flctl_platform_data *pdata; + int ret; + int irq; + struct mtd_part_parser_data ppdata = {}; + + flctl = devm_kzalloc(&pdev->dev, sizeof(struct sh_flctl), GFP_KERNEL); + if (!flctl) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + flctl->reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(flctl->reg)) + return PTR_ERR(flctl->reg); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "failed to get flste irq data\n"); + return -ENXIO; + } + + ret = devm_request_irq(&pdev->dev, irq, flctl_handle_flste, IRQF_SHARED, + "flste", flctl); + if (ret) { + dev_err(&pdev->dev, "request interrupt failed.\n"); + return ret; + } + + if (pdev->dev.of_node) + pdata = flctl_parse_dt(&pdev->dev); + else + pdata = dev_get_platdata(&pdev->dev); + + if (!pdata) { + dev_err(&pdev->dev, "no setup data defined\n"); + return -EINVAL; + } + + platform_set_drvdata(pdev, flctl); + flctl_mtd = &flctl->mtd; + nand = &flctl->chip; + flctl_mtd->priv = nand; + flctl->pdev = pdev; + flctl->hwecc = pdata->has_hwecc; + flctl->holden = pdata->use_holden; + flctl->flcmncr_base = pdata->flcmncr_val; + flctl->flintdmacr_base = flctl->hwecc ? (STERINTE | ECERB) : STERINTE; + + /* Set address of hardware control function */ + /* 20 us command delay time */ + nand->chip_delay = 20; + + nand->read_byte = flctl_read_byte; + nand->write_buf = flctl_write_buf; + nand->read_buf = flctl_read_buf; + nand->select_chip = flctl_select_chip; + nand->cmdfunc = flctl_cmdfunc; + + if (pdata->flcmncr_val & SEL_16BIT) { + nand->options |= NAND_BUSWIDTH_16; + nand->read_word = flctl_read_word; + } + + pm_runtime_enable(&pdev->dev); + pm_runtime_resume(&pdev->dev); + + flctl_setup_dma(flctl); + + ret = nand_scan_ident(flctl_mtd, 1, NULL); + if (ret) + goto err_chip; + + ret = flctl_chip_init_tail(flctl_mtd); + if (ret) + goto err_chip; + + ret = nand_scan_tail(flctl_mtd); + if (ret) + goto err_chip; + + ppdata.of_node = pdev->dev.of_node; + ret = mtd_device_parse_register(flctl_mtd, NULL, &ppdata, pdata->parts, + pdata->nr_parts); + + return 0; + +err_chip: + flctl_release_dma(flctl); + pm_runtime_disable(&pdev->dev); + return ret; +} + +static int flctl_remove(struct platform_device *pdev) +{ + struct sh_flctl *flctl = platform_get_drvdata(pdev); + + flctl_release_dma(flctl); + nand_release(&flctl->mtd); + pm_runtime_disable(&pdev->dev); + + return 0; +} + +static struct platform_driver flctl_driver = { + .remove = flctl_remove, + .driver = { + .name = "sh_flctl", + .of_match_table = of_match_ptr(of_flctl_match), + }, +}; + +module_platform_driver_probe(flctl_driver, flctl_probe); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Yoshihiro Shimoda"); +MODULE_DESCRIPTION("SuperH FLCTL driver"); +MODULE_ALIAS("platform:sh_flctl"); diff --git a/drivers/mtd/nand/sharpsl.c b/drivers/mtd/nand/sharpsl.c new file mode 100644 index 000000000..842c47a45 --- /dev/null +++ b/drivers/mtd/nand/sharpsl.c @@ -0,0 +1,232 @@ +/* + * drivers/mtd/nand/sharpsl.c + * + * Copyright (C) 2004 Richard Purdie + * Copyright (C) 2008 Dmitry Baryshkov + * + * Based on Sharp's NAND driver sharp_sl.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/genhd.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/sharpsl.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> + +#include <asm/io.h> +#include <mach/hardware.h> +#include <asm/mach-types.h> + +struct sharpsl_nand { + struct mtd_info mtd; + struct nand_chip chip; + + void __iomem *io; +}; + +#define mtd_to_sharpsl(_mtd) container_of(_mtd, struct sharpsl_nand, mtd) + +/* register offset */ +#define ECCLPLB 0x00 /* line parity 7 - 0 bit */ +#define ECCLPUB 0x04 /* line parity 15 - 8 bit */ +#define ECCCP 0x08 /* column parity 5 - 0 bit */ +#define ECCCNTR 0x0C /* ECC byte counter */ +#define ECCCLRR 0x10 /* cleare ECC */ +#define FLASHIO 0x14 /* Flash I/O */ +#define FLASHCTL 0x18 /* Flash Control */ + +/* Flash control bit */ +#define FLRYBY (1 << 5) +#define FLCE1 (1 << 4) +#define FLWP (1 << 3) +#define FLALE (1 << 2) +#define FLCLE (1 << 1) +#define FLCE0 (1 << 0) + +/* + * hardware specific access to control-lines + * ctrl: + * NAND_CNE: bit 0 -> ! bit 0 & 4 + * NAND_CLE: bit 1 -> bit 1 + * NAND_ALE: bit 2 -> bit 2 + * + */ +static void sharpsl_nand_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct sharpsl_nand *sharpsl = mtd_to_sharpsl(mtd); + struct nand_chip *chip = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + unsigned char bits = ctrl & 0x07; + + bits |= (ctrl & 0x01) << 4; + + bits ^= 0x11; + + writeb((readb(sharpsl->io + FLASHCTL) & ~0x17) | bits, sharpsl->io + FLASHCTL); + } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, chip->IO_ADDR_W); +} + +static int sharpsl_nand_dev_ready(struct mtd_info *mtd) +{ + struct sharpsl_nand *sharpsl = mtd_to_sharpsl(mtd); + return !((readb(sharpsl->io + FLASHCTL) & FLRYBY) == 0); +} + +static void sharpsl_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct sharpsl_nand *sharpsl = mtd_to_sharpsl(mtd); + writeb(0, sharpsl->io + ECCCLRR); +} + +static int sharpsl_nand_calculate_ecc(struct mtd_info *mtd, const u_char * dat, u_char * ecc_code) +{ + struct sharpsl_nand *sharpsl = mtd_to_sharpsl(mtd); + ecc_code[0] = ~readb(sharpsl->io + ECCLPUB); + ecc_code[1] = ~readb(sharpsl->io + ECCLPLB); + ecc_code[2] = (~readb(sharpsl->io + ECCCP) << 2) | 0x03; + return readb(sharpsl->io + ECCCNTR) != 0; +} + +/* + * Main initialization routine + */ +static int sharpsl_nand_probe(struct platform_device *pdev) +{ + struct nand_chip *this; + struct resource *r; + int err = 0; + struct sharpsl_nand *sharpsl; + struct sharpsl_nand_platform_data *data = dev_get_platdata(&pdev->dev); + + if (!data) { + dev_err(&pdev->dev, "no platform data!\n"); + return -EINVAL; + } + + /* Allocate memory for MTD device structure and private data */ + sharpsl = kzalloc(sizeof(struct sharpsl_nand), GFP_KERNEL); + if (!sharpsl) + return -ENOMEM; + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + dev_err(&pdev->dev, "no io memory resource defined!\n"); + err = -ENODEV; + goto err_get_res; + } + + /* map physical address */ + sharpsl->io = ioremap(r->start, resource_size(r)); + if (!sharpsl->io) { + dev_err(&pdev->dev, "ioremap to access Sharp SL NAND chip failed\n"); + err = -EIO; + goto err_ioremap; + } + + /* Get pointer to private data */ + this = (struct nand_chip *)(&sharpsl->chip); + + /* Link the private data with the MTD structure */ + sharpsl->mtd.priv = this; + sharpsl->mtd.owner = THIS_MODULE; + + platform_set_drvdata(pdev, sharpsl); + + /* + * PXA initialize + */ + writeb(readb(sharpsl->io + FLASHCTL) | FLWP, sharpsl->io + FLASHCTL); + + /* Set address of NAND IO lines */ + this->IO_ADDR_R = sharpsl->io + FLASHIO; + this->IO_ADDR_W = sharpsl->io + FLASHIO; + /* Set address of hardware control function */ + this->cmd_ctrl = sharpsl_nand_hwcontrol; + this->dev_ready = sharpsl_nand_dev_ready; + /* 15 us command delay time */ + this->chip_delay = 15; + /* set eccmode using hardware ECC */ + this->ecc.mode = NAND_ECC_HW; + this->ecc.size = 256; + this->ecc.bytes = 3; + this->ecc.strength = 1; + this->badblock_pattern = data->badblock_pattern; + this->ecc.layout = data->ecc_layout; + this->ecc.hwctl = sharpsl_nand_enable_hwecc; + this->ecc.calculate = sharpsl_nand_calculate_ecc; + this->ecc.correct = nand_correct_data; + + /* Scan to find existence of the device */ + err = nand_scan(&sharpsl->mtd, 1); + if (err) + goto err_scan; + + /* Register the partitions */ + sharpsl->mtd.name = "sharpsl-nand"; + + err = mtd_device_parse_register(&sharpsl->mtd, NULL, NULL, + data->partitions, data->nr_partitions); + if (err) + goto err_add; + + /* Return happy */ + return 0; + +err_add: + nand_release(&sharpsl->mtd); + +err_scan: + iounmap(sharpsl->io); +err_ioremap: +err_get_res: + kfree(sharpsl); + return err; +} + +/* + * Clean up routine + */ +static int sharpsl_nand_remove(struct platform_device *pdev) +{ + struct sharpsl_nand *sharpsl = platform_get_drvdata(pdev); + + /* Release resources, unregister device */ + nand_release(&sharpsl->mtd); + + iounmap(sharpsl->io); + + /* Free the MTD device structure */ + kfree(sharpsl); + + return 0; +} + +static struct platform_driver sharpsl_nand_driver = { + .driver = { + .name = "sharpsl-nand", + }, + .probe = sharpsl_nand_probe, + .remove = sharpsl_nand_remove, +}; + +module_platform_driver(sharpsl_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Richard Purdie <rpurdie@rpsys.net>"); +MODULE_DESCRIPTION("Device specific logic for NAND flash on Sharp SL-C7xx Series"); diff --git a/drivers/mtd/nand/sm_common.c b/drivers/mtd/nand/sm_common.c new file mode 100644 index 000000000..e06b5e5d3 --- /dev/null +++ b/drivers/mtd/nand/sm_common.c @@ -0,0 +1,141 @@ +/* + * Copyright © 2009 - Maxim Levitsky + * Common routines & support for xD format + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/kernel.h> +#include <linux/mtd/nand.h> +#include <linux/module.h> +#include <linux/sizes.h> +#include "sm_common.h" + +static struct nand_ecclayout nand_oob_sm = { + .eccbytes = 6, + .eccpos = {8, 9, 10, 13, 14, 15}, + .oobfree = { + {.offset = 0 , .length = 4}, /* reserved */ + {.offset = 6 , .length = 2}, /* LBA1 */ + {.offset = 11, .length = 2} /* LBA2 */ + } +}; + +/* NOTE: This layout is is not compatabable with SmartMedia, */ +/* because the 256 byte devices have page depenent oob layout */ +/* However it does preserve the bad block markers */ +/* If you use smftl, it will bypass this and work correctly */ +/* If you not, then you break SmartMedia compliance anyway */ + +static struct nand_ecclayout nand_oob_sm_small = { + .eccbytes = 3, + .eccpos = {0, 1, 2}, + .oobfree = { + {.offset = 3 , .length = 2}, /* reserved */ + {.offset = 6 , .length = 2}, /* LBA1 */ + } +}; + + +static int sm_block_markbad(struct mtd_info *mtd, loff_t ofs) +{ + struct mtd_oob_ops ops; + struct sm_oob oob; + int ret; + + memset(&oob, -1, SM_OOB_SIZE); + oob.block_status = 0x0F; + + /* As long as this function is called on erase block boundaries + it will work correctly for 256 byte nand */ + ops.mode = MTD_OPS_PLACE_OOB; + ops.ooboffs = 0; + ops.ooblen = mtd->oobsize; + ops.oobbuf = (void *)&oob; + ops.datbuf = NULL; + + + ret = mtd_write_oob(mtd, ofs, &ops); + if (ret < 0 || ops.oobretlen != SM_OOB_SIZE) { + printk(KERN_NOTICE + "sm_common: can't mark sector at %i as bad\n", + (int)ofs); + return -EIO; + } + + return 0; +} + +static struct nand_flash_dev nand_smartmedia_flash_ids[] = { + LEGACY_ID_NAND("SmartMedia 2MiB 3,3V ROM", 0x5d, 2, SZ_8K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 4MiB 3,3V", 0xe3, 4, SZ_8K, 0), + LEGACY_ID_NAND("SmartMedia 4MiB 3,3/5V", 0xe5, 4, SZ_8K, 0), + LEGACY_ID_NAND("SmartMedia 4MiB 5V", 0x6b, 4, SZ_8K, 0), + LEGACY_ID_NAND("SmartMedia 4MiB 3,3V ROM", 0xd5, 4, SZ_8K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 8MiB 3,3V", 0xe6, 8, SZ_8K, 0), + LEGACY_ID_NAND("SmartMedia 8MiB 3,3V ROM", 0xd6, 8, SZ_8K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 16MiB 3,3V", 0x73, 16, SZ_16K, 0), + LEGACY_ID_NAND("SmartMedia 16MiB 3,3V ROM", 0x57, 16, SZ_16K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 32MiB 3,3V", 0x75, 32, SZ_16K, 0), + LEGACY_ID_NAND("SmartMedia 32MiB 3,3V ROM", 0x58, 32, SZ_16K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 64MiB 3,3V", 0x76, 64, SZ_16K, 0), + LEGACY_ID_NAND("SmartMedia 64MiB 3,3V ROM", 0xd9, 64, SZ_16K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 128MiB 3,3V", 0x79, 128, SZ_16K, 0), + LEGACY_ID_NAND("SmartMedia 128MiB 3,3V ROM", 0xda, 128, SZ_16K, NAND_ROM), + LEGACY_ID_NAND("SmartMedia 256MiB 3, 3V", 0x71, 256, SZ_16K, 0), + LEGACY_ID_NAND("SmartMedia 256MiB 3,3V ROM", 0x5b, 256, SZ_16K, NAND_ROM), + {NULL} +}; + +static struct nand_flash_dev nand_xd_flash_ids[] = { + LEGACY_ID_NAND("xD 16MiB 3,3V", 0x73, 16, SZ_16K, 0), + LEGACY_ID_NAND("xD 32MiB 3,3V", 0x75, 32, SZ_16K, 0), + LEGACY_ID_NAND("xD 64MiB 3,3V", 0x76, 64, SZ_16K, 0), + LEGACY_ID_NAND("xD 128MiB 3,3V", 0x79, 128, SZ_16K, 0), + LEGACY_ID_NAND("xD 256MiB 3,3V", 0x71, 256, SZ_16K, NAND_BROKEN_XD), + LEGACY_ID_NAND("xD 512MiB 3,3V", 0xdc, 512, SZ_16K, NAND_BROKEN_XD), + LEGACY_ID_NAND("xD 1GiB 3,3V", 0xd3, 1024, SZ_16K, NAND_BROKEN_XD), + LEGACY_ID_NAND("xD 2GiB 3,3V", 0xd5, 2048, SZ_16K, NAND_BROKEN_XD), + {NULL} +}; + +int sm_register_device(struct mtd_info *mtd, int smartmedia) +{ + struct nand_chip *chip = mtd->priv; + int ret; + + chip->options |= NAND_SKIP_BBTSCAN; + + /* Scan for card properties */ + ret = nand_scan_ident(mtd, 1, smartmedia ? + nand_smartmedia_flash_ids : nand_xd_flash_ids); + + if (ret) + return ret; + + /* Bad block marker position */ + chip->badblockpos = 0x05; + chip->badblockbits = 7; + chip->block_markbad = sm_block_markbad; + + /* ECC layout */ + if (mtd->writesize == SM_SECTOR_SIZE) + chip->ecc.layout = &nand_oob_sm; + else if (mtd->writesize == SM_SMALL_PAGE) + chip->ecc.layout = &nand_oob_sm_small; + else + return -ENODEV; + + ret = nand_scan_tail(mtd); + + if (ret) + return ret; + + return mtd_device_register(mtd, NULL, 0); +} +EXPORT_SYMBOL_GPL(sm_register_device); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Maxim Levitsky <maximlevitsky@gmail.com>"); +MODULE_DESCRIPTION("Common SmartMedia/xD functions"); diff --git a/drivers/mtd/nand/sm_common.h b/drivers/mtd/nand/sm_common.h new file mode 100644 index 000000000..d3e028e58 --- /dev/null +++ b/drivers/mtd/nand/sm_common.h @@ -0,0 +1,61 @@ +/* + * Copyright © 2009 - Maxim Levitsky + * Common routines & support for SmartMedia/xD format + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/bitops.h> +#include <linux/mtd/mtd.h> + +/* Full oob structure as written on the flash */ +struct sm_oob { + uint32_t reserved; + uint8_t data_status; + uint8_t block_status; + uint8_t lba_copy1[2]; + uint8_t ecc2[3]; + uint8_t lba_copy2[2]; + uint8_t ecc1[3]; +} __packed; + + +/* one sector is always 512 bytes, but it can consist of two nand pages */ +#define SM_SECTOR_SIZE 512 + +/* oob area is also 16 bytes, but might be from two pages */ +#define SM_OOB_SIZE 16 + +/* This is maximum zone size, and all devices that have more that one zone + have this size */ +#define SM_MAX_ZONE_SIZE 1024 + +/* support for small page nand */ +#define SM_SMALL_PAGE 256 +#define SM_SMALL_OOB_SIZE 8 + + +extern int sm_register_device(struct mtd_info *mtd, int smartmedia); + + +static inline int sm_sector_valid(struct sm_oob *oob) +{ + return hweight16(oob->data_status) >= 5; +} + +static inline int sm_block_valid(struct sm_oob *oob) +{ + return hweight16(oob->block_status) >= 7; +} + +static inline int sm_block_erased(struct sm_oob *oob) +{ + static const uint32_t erased_pattern[4] = { + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF }; + + /* First test for erased block */ + if (!memcmp(oob, erased_pattern, sizeof(*oob))) + return 1; + return 0; +} diff --git a/drivers/mtd/nand/socrates_nand.c b/drivers/mtd/nand/socrates_nand.c new file mode 100644 index 000000000..d71062273 --- /dev/null +++ b/drivers/mtd/nand/socrates_nand.c @@ -0,0 +1,253 @@ +/* + * drivers/mtd/nand/socrates_nand.c + * + * Copyright © 2008 Ilya Yanok, Emcraft Systems + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/io.h> + +#define FPGA_NAND_CMD_MASK (0x7 << 28) +#define FPGA_NAND_CMD_COMMAND (0x0 << 28) +#define FPGA_NAND_CMD_ADDR (0x1 << 28) +#define FPGA_NAND_CMD_READ (0x2 << 28) +#define FPGA_NAND_CMD_WRITE (0x3 << 28) +#define FPGA_NAND_BUSY (0x1 << 15) +#define FPGA_NAND_ENABLE (0x1 << 31) +#define FPGA_NAND_DATA_SHIFT 16 + +struct socrates_nand_host { + struct nand_chip nand_chip; + struct mtd_info mtd; + void __iomem *io_base; + struct device *dev; +}; + +/** + * socrates_nand_write_buf - write buffer to chip + * @mtd: MTD device structure + * @buf: data buffer + * @len: number of bytes to write + */ +static void socrates_nand_write_buf(struct mtd_info *mtd, + const uint8_t *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + struct socrates_nand_host *host = this->priv; + + for (i = 0; i < len; i++) { + out_be32(host->io_base, FPGA_NAND_ENABLE | + FPGA_NAND_CMD_WRITE | + (buf[i] << FPGA_NAND_DATA_SHIFT)); + } +} + +/** + * socrates_nand_read_buf - read chip data into buffer + * @mtd: MTD device structure + * @buf: buffer to store date + * @len: number of bytes to read + */ +static void socrates_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + int i; + struct nand_chip *this = mtd->priv; + struct socrates_nand_host *host = this->priv; + uint32_t val; + + val = FPGA_NAND_ENABLE | FPGA_NAND_CMD_READ; + + out_be32(host->io_base, val); + for (i = 0; i < len; i++) { + buf[i] = (in_be32(host->io_base) >> + FPGA_NAND_DATA_SHIFT) & 0xff; + } +} + +/** + * socrates_nand_read_byte - read one byte from the chip + * @mtd: MTD device structure + */ +static uint8_t socrates_nand_read_byte(struct mtd_info *mtd) +{ + uint8_t byte; + socrates_nand_read_buf(mtd, &byte, sizeof(byte)); + return byte; +} + +/** + * socrates_nand_read_word - read one word from the chip + * @mtd: MTD device structure + */ +static uint16_t socrates_nand_read_word(struct mtd_info *mtd) +{ + uint16_t word; + socrates_nand_read_buf(mtd, (uint8_t *)&word, sizeof(word)); + return word; +} + +/* + * Hardware specific access to control-lines + */ +static void socrates_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *nand_chip = mtd->priv; + struct socrates_nand_host *host = nand_chip->priv; + uint32_t val; + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + val = FPGA_NAND_CMD_COMMAND; + else + val = FPGA_NAND_CMD_ADDR; + + if (ctrl & NAND_NCE) + val |= FPGA_NAND_ENABLE; + + val |= (cmd & 0xff) << FPGA_NAND_DATA_SHIFT; + + out_be32(host->io_base, val); +} + +/* + * Read the Device Ready pin. + */ +static int socrates_nand_device_ready(struct mtd_info *mtd) +{ + struct nand_chip *nand_chip = mtd->priv; + struct socrates_nand_host *host = nand_chip->priv; + + if (in_be32(host->io_base) & FPGA_NAND_BUSY) + return 0; /* busy */ + return 1; +} + +/* + * Probe for the NAND device. + */ +static int socrates_nand_probe(struct platform_device *ofdev) +{ + struct socrates_nand_host *host; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + int res; + struct mtd_part_parser_data ppdata; + + /* Allocate memory for the device structure (and zero it) */ + host = devm_kzalloc(&ofdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + + host->io_base = of_iomap(ofdev->dev.of_node, 0); + if (host->io_base == NULL) { + dev_err(&ofdev->dev, "ioremap failed\n"); + return -EIO; + } + + mtd = &host->mtd; + nand_chip = &host->nand_chip; + host->dev = &ofdev->dev; + + nand_chip->priv = host; /* link the private data structures */ + mtd->priv = nand_chip; + mtd->name = "socrates_nand"; + mtd->owner = THIS_MODULE; + mtd->dev.parent = &ofdev->dev; + ppdata.of_node = ofdev->dev.of_node; + + /*should never be accessed directly */ + nand_chip->IO_ADDR_R = (void *)0xdeadbeef; + nand_chip->IO_ADDR_W = (void *)0xdeadbeef; + + nand_chip->cmd_ctrl = socrates_nand_cmd_ctrl; + nand_chip->read_byte = socrates_nand_read_byte; + nand_chip->read_word = socrates_nand_read_word; + nand_chip->write_buf = socrates_nand_write_buf; + nand_chip->read_buf = socrates_nand_read_buf; + nand_chip->dev_ready = socrates_nand_device_ready; + + nand_chip->ecc.mode = NAND_ECC_SOFT; /* enable ECC */ + + /* TODO: I have no idea what real delay is. */ + nand_chip->chip_delay = 20; /* 20us command delay time */ + + dev_set_drvdata(&ofdev->dev, host); + + /* first scan to find the device and get the page size */ + if (nand_scan_ident(mtd, 1, NULL)) { + res = -ENXIO; + goto out; + } + + /* second phase scan */ + if (nand_scan_tail(mtd)) { + res = -ENXIO; + goto out; + } + + res = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (!res) + return res; + + nand_release(mtd); + +out: + iounmap(host->io_base); + return res; +} + +/* + * Remove a NAND device. + */ +static int socrates_nand_remove(struct platform_device *ofdev) +{ + struct socrates_nand_host *host = dev_get_drvdata(&ofdev->dev); + struct mtd_info *mtd = &host->mtd; + + nand_release(mtd); + + iounmap(host->io_base); + + return 0; +} + +static const struct of_device_id socrates_nand_match[] = +{ + { + .compatible = "abb,socrates-nand", + }, + {}, +}; + +MODULE_DEVICE_TABLE(of, socrates_nand_match); + +static struct platform_driver socrates_nand_driver = { + .driver = { + .name = "socrates_nand", + .of_match_table = socrates_nand_match, + }, + .probe = socrates_nand_probe, + .remove = socrates_nand_remove, +}; + +module_platform_driver(socrates_nand_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Ilya Yanok"); +MODULE_DESCRIPTION("NAND driver for Socrates board"); diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c new file mode 100644 index 000000000..6f93b2990 --- /dev/null +++ b/drivers/mtd/nand/sunxi_nand.c @@ -0,0 +1,1430 @@ +/* + * Copyright (C) 2013 Boris BREZILLON <b.brezillon.dev@gmail.com> + * + * Derived from: + * https://github.com/yuq/sunxi-nfc-mtd + * Copyright (C) 2013 Qiang Yu <yuq825@gmail.com> + * + * https://github.com/hno/Allwinner-Info + * Copyright (C) 2013 Henrik Nordström <Henrik Nordström> + * + * Copyright (C) 2013 Dmitriy B. <rzk333@gmail.com> + * Copyright (C) 2013 Sergey Lapin <slapin@ossfans.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/dma-mapping.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/of_mtd.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/dmaengine.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/io.h> + +#define NFC_REG_CTL 0x0000 +#define NFC_REG_ST 0x0004 +#define NFC_REG_INT 0x0008 +#define NFC_REG_TIMING_CTL 0x000C +#define NFC_REG_TIMING_CFG 0x0010 +#define NFC_REG_ADDR_LOW 0x0014 +#define NFC_REG_ADDR_HIGH 0x0018 +#define NFC_REG_SECTOR_NUM 0x001C +#define NFC_REG_CNT 0x0020 +#define NFC_REG_CMD 0x0024 +#define NFC_REG_RCMD_SET 0x0028 +#define NFC_REG_WCMD_SET 0x002C +#define NFC_REG_IO_DATA 0x0030 +#define NFC_REG_ECC_CTL 0x0034 +#define NFC_REG_ECC_ST 0x0038 +#define NFC_REG_DEBUG 0x003C +#define NFC_REG_ECC_CNT0 0x0040 +#define NFC_REG_ECC_CNT1 0x0044 +#define NFC_REG_ECC_CNT2 0x0048 +#define NFC_REG_ECC_CNT3 0x004c +#define NFC_REG_USER_DATA_BASE 0x0050 +#define NFC_REG_SPARE_AREA 0x00A0 +#define NFC_RAM0_BASE 0x0400 +#define NFC_RAM1_BASE 0x0800 + +/* define bit use in NFC_CTL */ +#define NFC_EN BIT(0) +#define NFC_RESET BIT(1) +#define NFC_BUS_WIDYH BIT(2) +#define NFC_RB_SEL BIT(3) +#define NFC_CE_SEL GENMASK(26, 24) +#define NFC_CE_CTL BIT(6) +#define NFC_CE_CTL1 BIT(7) +#define NFC_PAGE_SIZE GENMASK(11, 8) +#define NFC_SAM BIT(12) +#define NFC_RAM_METHOD BIT(14) +#define NFC_DEBUG_CTL BIT(31) + +/* define bit use in NFC_ST */ +#define NFC_RB_B2R BIT(0) +#define NFC_CMD_INT_FLAG BIT(1) +#define NFC_DMA_INT_FLAG BIT(2) +#define NFC_CMD_FIFO_STATUS BIT(3) +#define NFC_STA BIT(4) +#define NFC_NATCH_INT_FLAG BIT(5) +#define NFC_RB_STATE0 BIT(8) +#define NFC_RB_STATE1 BIT(9) +#define NFC_RB_STATE2 BIT(10) +#define NFC_RB_STATE3 BIT(11) + +/* define bit use in NFC_INT */ +#define NFC_B2R_INT_ENABLE BIT(0) +#define NFC_CMD_INT_ENABLE BIT(1) +#define NFC_DMA_INT_ENABLE BIT(2) +#define NFC_INT_MASK (NFC_B2R_INT_ENABLE | \ + NFC_CMD_INT_ENABLE | \ + NFC_DMA_INT_ENABLE) + +/* define bit use in NFC_CMD */ +#define NFC_CMD_LOW_BYTE GENMASK(7, 0) +#define NFC_CMD_HIGH_BYTE GENMASK(15, 8) +#define NFC_ADR_NUM GENMASK(18, 16) +#define NFC_SEND_ADR BIT(19) +#define NFC_ACCESS_DIR BIT(20) +#define NFC_DATA_TRANS BIT(21) +#define NFC_SEND_CMD1 BIT(22) +#define NFC_WAIT_FLAG BIT(23) +#define NFC_SEND_CMD2 BIT(24) +#define NFC_SEQ BIT(25) +#define NFC_DATA_SWAP_METHOD BIT(26) +#define NFC_ROW_AUTO_INC BIT(27) +#define NFC_SEND_CMD3 BIT(28) +#define NFC_SEND_CMD4 BIT(29) +#define NFC_CMD_TYPE GENMASK(31, 30) + +/* define bit use in NFC_RCMD_SET */ +#define NFC_READ_CMD GENMASK(7, 0) +#define NFC_RANDOM_READ_CMD0 GENMASK(15, 8) +#define NFC_RANDOM_READ_CMD1 GENMASK(23, 16) + +/* define bit use in NFC_WCMD_SET */ +#define NFC_PROGRAM_CMD GENMASK(7, 0) +#define NFC_RANDOM_WRITE_CMD GENMASK(15, 8) +#define NFC_READ_CMD0 GENMASK(23, 16) +#define NFC_READ_CMD1 GENMASK(31, 24) + +/* define bit use in NFC_ECC_CTL */ +#define NFC_ECC_EN BIT(0) +#define NFC_ECC_PIPELINE BIT(3) +#define NFC_ECC_EXCEPTION BIT(4) +#define NFC_ECC_BLOCK_SIZE BIT(5) +#define NFC_RANDOM_EN BIT(9) +#define NFC_RANDOM_DIRECTION BIT(10) +#define NFC_ECC_MODE_SHIFT 12 +#define NFC_ECC_MODE GENMASK(15, 12) +#define NFC_RANDOM_SEED GENMASK(30, 16) + +#define NFC_DEFAULT_TIMEOUT_MS 1000 + +#define NFC_SRAM_SIZE 1024 + +#define NFC_MAX_CS 7 + +/* + * Ready/Busy detection type: describes the Ready/Busy detection modes + * + * @RB_NONE: no external detection available, rely on STATUS command + * and software timeouts + * @RB_NATIVE: use sunxi NAND controller Ready/Busy support. The Ready/Busy + * pin of the NAND flash chip must be connected to one of the + * native NAND R/B pins (those which can be muxed to the NAND + * Controller) + * @RB_GPIO: use a simple GPIO to handle Ready/Busy status. The Ready/Busy + * pin of the NAND flash chip must be connected to a GPIO capable + * pin. + */ +enum sunxi_nand_rb_type { + RB_NONE, + RB_NATIVE, + RB_GPIO, +}; + +/* + * Ready/Busy structure: stores information related to Ready/Busy detection + * + * @type: the Ready/Busy detection mode + * @info: information related to the R/B detection mode. Either a gpio + * id or a native R/B id (those supported by the NAND controller). + */ +struct sunxi_nand_rb { + enum sunxi_nand_rb_type type; + union { + int gpio; + int nativeid; + } info; +}; + +/* + * Chip Select structure: stores information related to NAND Chip Select + * + * @cs: the NAND CS id used to communicate with a NAND Chip + * @rb: the Ready/Busy description + */ +struct sunxi_nand_chip_sel { + u8 cs; + struct sunxi_nand_rb rb; +}; + +/* + * sunxi HW ECC infos: stores information related to HW ECC support + * + * @mode: the sunxi ECC mode field deduced from ECC requirements + * @layout: the OOB layout depending on the ECC requirements and the + * selected ECC mode + */ +struct sunxi_nand_hw_ecc { + int mode; + struct nand_ecclayout layout; +}; + +/* + * NAND chip structure: stores NAND chip device related information + * + * @node: used to store NAND chips into a list + * @nand: base NAND chip structure + * @mtd: base MTD structure + * @clk_rate: clk_rate required for this NAND chip + * @selected: current active CS + * @nsels: number of CS lines required by the NAND chip + * @sels: array of CS lines descriptions + */ +struct sunxi_nand_chip { + struct list_head node; + struct nand_chip nand; + struct mtd_info mtd; + unsigned long clk_rate; + int selected; + int nsels; + struct sunxi_nand_chip_sel sels[0]; +}; + +static inline struct sunxi_nand_chip *to_sunxi_nand(struct nand_chip *nand) +{ + return container_of(nand, struct sunxi_nand_chip, nand); +} + +/* + * NAND Controller structure: stores sunxi NAND controller information + * + * @controller: base controller structure + * @dev: parent device (used to print error messages) + * @regs: NAND controller registers + * @ahb_clk: NAND Controller AHB clock + * @mod_clk: NAND Controller mod clock + * @assigned_cs: bitmask describing already assigned CS lines + * @clk_rate: NAND controller current clock rate + * @chips: a list containing all the NAND chips attached to + * this NAND controller + * @complete: a completion object used to wait for NAND + * controller events + */ +struct sunxi_nfc { + struct nand_hw_control controller; + struct device *dev; + void __iomem *regs; + struct clk *ahb_clk; + struct clk *mod_clk; + unsigned long assigned_cs; + unsigned long clk_rate; + struct list_head chips; + struct completion complete; +}; + +static inline struct sunxi_nfc *to_sunxi_nfc(struct nand_hw_control *ctrl) +{ + return container_of(ctrl, struct sunxi_nfc, controller); +} + +static irqreturn_t sunxi_nfc_interrupt(int irq, void *dev_id) +{ + struct sunxi_nfc *nfc = dev_id; + u32 st = readl(nfc->regs + NFC_REG_ST); + u32 ien = readl(nfc->regs + NFC_REG_INT); + + if (!(ien & st)) + return IRQ_NONE; + + if ((ien & st) == ien) + complete(&nfc->complete); + + writel(st & NFC_INT_MASK, nfc->regs + NFC_REG_ST); + writel(~st & ien & NFC_INT_MASK, nfc->regs + NFC_REG_INT); + + return IRQ_HANDLED; +} + +static int sunxi_nfc_wait_int(struct sunxi_nfc *nfc, u32 flags, + unsigned int timeout_ms) +{ + init_completion(&nfc->complete); + + writel(flags, nfc->regs + NFC_REG_INT); + + if (!timeout_ms) + timeout_ms = NFC_DEFAULT_TIMEOUT_MS; + + if (!wait_for_completion_timeout(&nfc->complete, + msecs_to_jiffies(timeout_ms))) { + dev_err(nfc->dev, "wait interrupt timedout\n"); + return -ETIMEDOUT; + } + + return 0; +} + +static int sunxi_nfc_wait_cmd_fifo_empty(struct sunxi_nfc *nfc) +{ + unsigned long timeout = jiffies + + msecs_to_jiffies(NFC_DEFAULT_TIMEOUT_MS); + + do { + if (!(readl(nfc->regs + NFC_REG_ST) & NFC_CMD_FIFO_STATUS)) + return 0; + } while (time_before(jiffies, timeout)); + + dev_err(nfc->dev, "wait for empty cmd FIFO timedout\n"); + return -ETIMEDOUT; +} + +static int sunxi_nfc_rst(struct sunxi_nfc *nfc) +{ + unsigned long timeout = jiffies + + msecs_to_jiffies(NFC_DEFAULT_TIMEOUT_MS); + + writel(0, nfc->regs + NFC_REG_ECC_CTL); + writel(NFC_RESET, nfc->regs + NFC_REG_CTL); + + do { + if (!(readl(nfc->regs + NFC_REG_CTL) & NFC_RESET)) + return 0; + } while (time_before(jiffies, timeout)); + + dev_err(nfc->dev, "wait for NAND controller reset timedout\n"); + return -ETIMEDOUT; +} + +static int sunxi_nfc_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + struct sunxi_nand_rb *rb; + unsigned long timeo = (sunxi_nand->nand.state == FL_ERASING ? 400 : 20); + int ret; + + if (sunxi_nand->selected < 0) + return 0; + + rb = &sunxi_nand->sels[sunxi_nand->selected].rb; + + switch (rb->type) { + case RB_NATIVE: + ret = !!(readl(nfc->regs + NFC_REG_ST) & + (NFC_RB_STATE0 << rb->info.nativeid)); + if (ret) + break; + + sunxi_nfc_wait_int(nfc, NFC_RB_B2R, timeo); + ret = !!(readl(nfc->regs + NFC_REG_ST) & + (NFC_RB_STATE0 << rb->info.nativeid)); + break; + case RB_GPIO: + ret = gpio_get_value(rb->info.gpio); + break; + case RB_NONE: + default: + ret = 0; + dev_err(nfc->dev, "cannot check R/B NAND status!\n"); + break; + } + + return ret; +} + +static void sunxi_nfc_select_chip(struct mtd_info *mtd, int chip) +{ + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + struct sunxi_nand_chip_sel *sel; + u32 ctl; + + if (chip > 0 && chip >= sunxi_nand->nsels) + return; + + if (chip == sunxi_nand->selected) + return; + + ctl = readl(nfc->regs + NFC_REG_CTL) & + ~(NFC_CE_SEL | NFC_RB_SEL | NFC_EN); + + if (chip >= 0) { + sel = &sunxi_nand->sels[chip]; + + ctl |= (sel->cs << 24) | NFC_EN | + (((nand->page_shift - 10) & 0xf) << 8); + if (sel->rb.type == RB_NONE) { + nand->dev_ready = NULL; + } else { + nand->dev_ready = sunxi_nfc_dev_ready; + if (sel->rb.type == RB_NATIVE) + ctl |= (sel->rb.info.nativeid << 3); + } + + writel(mtd->writesize, nfc->regs + NFC_REG_SPARE_AREA); + + if (nfc->clk_rate != sunxi_nand->clk_rate) { + clk_set_rate(nfc->mod_clk, sunxi_nand->clk_rate); + nfc->clk_rate = sunxi_nand->clk_rate; + } + } + + writel(ctl, nfc->regs + NFC_REG_CTL); + + sunxi_nand->selected = chip; +} + +static void sunxi_nfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + int ret; + int cnt; + int offs = 0; + u32 tmp; + + while (len > offs) { + cnt = min(len - offs, NFC_SRAM_SIZE); + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + break; + + writel(cnt, nfc->regs + NFC_REG_CNT); + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD; + writel(tmp, nfc->regs + NFC_REG_CMD); + + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + break; + + if (buf) + memcpy_fromio(buf + offs, nfc->regs + NFC_RAM0_BASE, + cnt); + offs += cnt; + } +} + +static void sunxi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, + int len) +{ + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + int ret; + int cnt; + int offs = 0; + u32 tmp; + + while (len > offs) { + cnt = min(len - offs, NFC_SRAM_SIZE); + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + break; + + writel(cnt, nfc->regs + NFC_REG_CNT); + memcpy_toio(nfc->regs + NFC_RAM0_BASE, buf + offs, cnt); + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | + NFC_ACCESS_DIR; + writel(tmp, nfc->regs + NFC_REG_CMD); + + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + break; + + offs += cnt; + } +} + +static uint8_t sunxi_nfc_read_byte(struct mtd_info *mtd) +{ + uint8_t ret; + + sunxi_nfc_read_buf(mtd, &ret, 1); + + return ret; +} + +static void sunxi_nfc_cmd_ctrl(struct mtd_info *mtd, int dat, + unsigned int ctrl) +{ + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + int ret; + u32 tmp; + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + return; + + if (ctrl & NAND_CTRL_CHANGE) { + tmp = readl(nfc->regs + NFC_REG_CTL); + if (ctrl & NAND_NCE) + tmp |= NFC_CE_CTL; + else + tmp &= ~NFC_CE_CTL; + writel(tmp, nfc->regs + NFC_REG_CTL); + } + + if (dat == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) { + writel(NFC_SEND_CMD1 | dat, nfc->regs + NFC_REG_CMD); + } else { + writel(dat, nfc->regs + NFC_REG_ADDR_LOW); + writel(NFC_SEND_ADR, nfc->regs + NFC_REG_CMD); + } + + sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); +} + +static int sunxi_nfc_hw_ecc_read_page(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +{ + struct sunxi_nfc *nfc = to_sunxi_nfc(chip->controller); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_ecclayout *layout = ecc->layout; + struct sunxi_nand_hw_ecc *data = ecc->priv; + unsigned int max_bitflips = 0; + int offset; + int ret; + u32 tmp; + int i; + int cnt; + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~(NFC_ECC_MODE | NFC_ECC_PIPELINE | NFC_ECC_BLOCK_SIZE); + tmp |= NFC_ECC_EN | (data->mode << NFC_ECC_MODE_SHIFT) | + NFC_ECC_EXCEPTION; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + for (i = 0; i < ecc->steps; i++) { + if (i) + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, i * ecc->size, -1); + + offset = mtd->writesize + layout->eccpos[i * ecc->bytes] - 4; + + chip->read_buf(mtd, NULL, ecc->size); + + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + return ret; + + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | (1 << 30); + writel(tmp, nfc->regs + NFC_REG_CMD); + + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + return ret; + + memcpy_fromio(buf + (i * ecc->size), + nfc->regs + NFC_RAM0_BASE, ecc->size); + + if (readl(nfc->regs + NFC_REG_ECC_ST) & 0x1) { + mtd->ecc_stats.failed++; + } else { + tmp = readl(nfc->regs + NFC_REG_ECC_CNT0) & 0xff; + mtd->ecc_stats.corrected += tmp; + max_bitflips = max_t(unsigned int, max_bitflips, tmp); + } + + if (oob_required) { + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + return ret; + + offset -= mtd->writesize; + chip->read_buf(mtd, chip->oob_poi + offset, + ecc->bytes + 4); + } + } + + if (oob_required) { + cnt = ecc->layout->oobfree[ecc->steps].length; + if (cnt > 0) { + offset = mtd->writesize + + ecc->layout->oobfree[ecc->steps].offset; + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); + offset -= mtd->writesize; + chip->read_buf(mtd, chip->oob_poi + offset, cnt); + } + } + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~NFC_ECC_EN; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + return max_bitflips; +} + +static int sunxi_nfc_hw_ecc_write_page(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + struct sunxi_nfc *nfc = to_sunxi_nfc(chip->controller); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_ecclayout *layout = ecc->layout; + struct sunxi_nand_hw_ecc *data = ecc->priv; + int offset; + int ret; + u32 tmp; + int i; + int cnt; + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~(NFC_ECC_MODE | NFC_ECC_PIPELINE | NFC_ECC_BLOCK_SIZE); + tmp |= NFC_ECC_EN | (data->mode << NFC_ECC_MODE_SHIFT) | + NFC_ECC_EXCEPTION; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + for (i = 0; i < ecc->steps; i++) { + if (i) + chip->cmdfunc(mtd, NAND_CMD_RNDIN, i * ecc->size, -1); + + chip->write_buf(mtd, buf + (i * ecc->size), ecc->size); + + offset = layout->eccpos[i * ecc->bytes] - 4 + mtd->writesize; + + /* Fill OOB data in */ + if (oob_required) { + tmp = 0xffffffff; + memcpy_toio(nfc->regs + NFC_REG_USER_DATA_BASE, &tmp, + 4); + } else { + memcpy_toio(nfc->regs + NFC_REG_USER_DATA_BASE, + chip->oob_poi + offset - mtd->writesize, + 4); + } + + chip->cmdfunc(mtd, NAND_CMD_RNDIN, offset, -1); + + ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); + if (ret) + return ret; + + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | NFC_ACCESS_DIR | + (1 << 30); + writel(tmp, nfc->regs + NFC_REG_CMD); + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + return ret; + } + + if (oob_required) { + cnt = ecc->layout->oobfree[i].length; + if (cnt > 0) { + offset = mtd->writesize + + ecc->layout->oobfree[i].offset; + chip->cmdfunc(mtd, NAND_CMD_RNDIN, offset, -1); + offset -= mtd->writesize; + chip->write_buf(mtd, chip->oob_poi + offset, cnt); + } + } + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~NFC_ECC_EN; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + return 0; +} + +static int sunxi_nfc_hw_syndrome_ecc_read_page(struct mtd_info *mtd, + struct nand_chip *chip, + uint8_t *buf, int oob_required, + int page) +{ + struct sunxi_nfc *nfc = to_sunxi_nfc(chip->controller); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct sunxi_nand_hw_ecc *data = ecc->priv; + unsigned int max_bitflips = 0; + uint8_t *oob = chip->oob_poi; + int offset = 0; + int ret; + int cnt; + u32 tmp; + int i; + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~(NFC_ECC_MODE | NFC_ECC_PIPELINE | NFC_ECC_BLOCK_SIZE); + tmp |= NFC_ECC_EN | (data->mode << NFC_ECC_MODE_SHIFT) | + NFC_ECC_EXCEPTION; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + for (i = 0; i < ecc->steps; i++) { + chip->read_buf(mtd, NULL, ecc->size); + + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | (1 << 30); + writel(tmp, nfc->regs + NFC_REG_CMD); + + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + return ret; + + memcpy_fromio(buf, nfc->regs + NFC_RAM0_BASE, ecc->size); + buf += ecc->size; + offset += ecc->size; + + if (readl(nfc->regs + NFC_REG_ECC_ST) & 0x1) { + mtd->ecc_stats.failed++; + } else { + tmp = readl(nfc->regs + NFC_REG_ECC_CNT0) & 0xff; + mtd->ecc_stats.corrected += tmp; + max_bitflips = max_t(unsigned int, max_bitflips, tmp); + } + + if (oob_required) { + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); + chip->read_buf(mtd, oob, ecc->bytes + ecc->prepad); + oob += ecc->bytes + ecc->prepad; + } + + offset += ecc->bytes + ecc->prepad; + } + + if (oob_required) { + cnt = mtd->oobsize - (oob - chip->oob_poi); + if (cnt > 0) { + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); + chip->read_buf(mtd, oob, cnt); + } + } + + writel(readl(nfc->regs + NFC_REG_ECC_CTL) & ~NFC_ECC_EN, + nfc->regs + NFC_REG_ECC_CTL); + + return max_bitflips; +} + +static int sunxi_nfc_hw_syndrome_ecc_write_page(struct mtd_info *mtd, + struct nand_chip *chip, + const uint8_t *buf, + int oob_required) +{ + struct sunxi_nfc *nfc = to_sunxi_nfc(chip->controller); + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct sunxi_nand_hw_ecc *data = ecc->priv; + uint8_t *oob = chip->oob_poi; + int offset = 0; + int ret; + int cnt; + u32 tmp; + int i; + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~(NFC_ECC_MODE | NFC_ECC_PIPELINE | NFC_ECC_BLOCK_SIZE); + tmp |= NFC_ECC_EN | (data->mode << NFC_ECC_MODE_SHIFT) | + NFC_ECC_EXCEPTION; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + for (i = 0; i < ecc->steps; i++) { + chip->write_buf(mtd, buf + (i * ecc->size), ecc->size); + offset += ecc->size; + + /* Fill OOB data in */ + if (oob_required) { + tmp = 0xffffffff; + memcpy_toio(nfc->regs + NFC_REG_USER_DATA_BASE, &tmp, + 4); + } else { + memcpy_toio(nfc->regs + NFC_REG_USER_DATA_BASE, oob, + 4); + } + + tmp = NFC_DATA_TRANS | NFC_DATA_SWAP_METHOD | NFC_ACCESS_DIR | + (1 << 30); + writel(tmp, nfc->regs + NFC_REG_CMD); + + ret = sunxi_nfc_wait_int(nfc, NFC_CMD_INT_FLAG, 0); + if (ret) + return ret; + + offset += ecc->bytes + ecc->prepad; + oob += ecc->bytes + ecc->prepad; + } + + if (oob_required) { + cnt = mtd->oobsize - (oob - chip->oob_poi); + if (cnt > 0) { + chip->cmdfunc(mtd, NAND_CMD_RNDIN, offset, -1); + chip->write_buf(mtd, oob, cnt); + } + } + + tmp = readl(nfc->regs + NFC_REG_ECC_CTL); + tmp &= ~NFC_ECC_EN; + + writel(tmp, nfc->regs + NFC_REG_ECC_CTL); + + return 0; +} + +static int sunxi_nand_chip_set_timings(struct sunxi_nand_chip *chip, + const struct nand_sdr_timings *timings) +{ + u32 min_clk_period = 0; + + /* T1 <=> tCLS */ + if (timings->tCLS_min > min_clk_period) + min_clk_period = timings->tCLS_min; + + /* T2 <=> tCLH */ + if (timings->tCLH_min > min_clk_period) + min_clk_period = timings->tCLH_min; + + /* T3 <=> tCS */ + if (timings->tCS_min > min_clk_period) + min_clk_period = timings->tCS_min; + + /* T4 <=> tCH */ + if (timings->tCH_min > min_clk_period) + min_clk_period = timings->tCH_min; + + /* T5 <=> tWP */ + if (timings->tWP_min > min_clk_period) + min_clk_period = timings->tWP_min; + + /* T6 <=> tWH */ + if (timings->tWH_min > min_clk_period) + min_clk_period = timings->tWH_min; + + /* T7 <=> tALS */ + if (timings->tALS_min > min_clk_period) + min_clk_period = timings->tALS_min; + + /* T8 <=> tDS */ + if (timings->tDS_min > min_clk_period) + min_clk_period = timings->tDS_min; + + /* T9 <=> tDH */ + if (timings->tDH_min > min_clk_period) + min_clk_period = timings->tDH_min; + + /* T10 <=> tRR */ + if (timings->tRR_min > (min_clk_period * 3)) + min_clk_period = DIV_ROUND_UP(timings->tRR_min, 3); + + /* T11 <=> tALH */ + if (timings->tALH_min > min_clk_period) + min_clk_period = timings->tALH_min; + + /* T12 <=> tRP */ + if (timings->tRP_min > min_clk_period) + min_clk_period = timings->tRP_min; + + /* T13 <=> tREH */ + if (timings->tREH_min > min_clk_period) + min_clk_period = timings->tREH_min; + + /* T14 <=> tRC */ + if (timings->tRC_min > (min_clk_period * 2)) + min_clk_period = DIV_ROUND_UP(timings->tRC_min, 2); + + /* T15 <=> tWC */ + if (timings->tWC_min > (min_clk_period * 2)) + min_clk_period = DIV_ROUND_UP(timings->tWC_min, 2); + + + /* Convert min_clk_period from picoseconds to nanoseconds */ + min_clk_period = DIV_ROUND_UP(min_clk_period, 1000); + + /* + * Convert min_clk_period into a clk frequency, then get the + * appropriate rate for the NAND controller IP given this formula + * (specified in the datasheet): + * nand clk_rate = 2 * min_clk_rate + */ + chip->clk_rate = (2 * NSEC_PER_SEC) / min_clk_period; + + /* TODO: configure T16-T19 */ + + return 0; +} + +static int sunxi_nand_chip_init_timings(struct sunxi_nand_chip *chip, + struct device_node *np) +{ + const struct nand_sdr_timings *timings; + int ret; + int mode; + + mode = onfi_get_async_timing_mode(&chip->nand); + if (mode == ONFI_TIMING_MODE_UNKNOWN) { + mode = chip->nand.onfi_timing_mode_default; + } else { + uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {}; + + mode = fls(mode) - 1; + if (mode < 0) + mode = 0; + + feature[0] = mode; + ret = chip->nand.onfi_set_features(&chip->mtd, &chip->nand, + ONFI_FEATURE_ADDR_TIMING_MODE, + feature); + if (ret) + return ret; + } + + timings = onfi_async_timing_mode_to_sdr_timings(mode); + if (IS_ERR(timings)) + return PTR_ERR(timings); + + return sunxi_nand_chip_set_timings(chip, timings); +} + +static int sunxi_nand_hw_common_ecc_ctrl_init(struct mtd_info *mtd, + struct nand_ecc_ctrl *ecc, + struct device_node *np) +{ + static const u8 strengths[] = { 16, 24, 28, 32, 40, 48, 56, 60, 64 }; + struct nand_chip *nand = mtd->priv; + struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand); + struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller); + struct sunxi_nand_hw_ecc *data; + struct nand_ecclayout *layout; + int nsectors; + int ret; + int i; + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + /* Add ECC info retrieval from DT */ + for (i = 0; i < ARRAY_SIZE(strengths); i++) { + if (ecc->strength <= strengths[i]) + break; + } + + if (i >= ARRAY_SIZE(strengths)) { + dev_err(nfc->dev, "unsupported strength\n"); + ret = -ENOTSUPP; + goto err; + } + + data->mode = i; + + /* HW ECC always request ECC bytes for 1024 bytes blocks */ + ecc->bytes = DIV_ROUND_UP(ecc->strength * fls(8 * 1024), 8); + + /* HW ECC always work with even numbers of ECC bytes */ + ecc->bytes = ALIGN(ecc->bytes, 2); + + layout = &data->layout; + nsectors = mtd->writesize / ecc->size; + + if (mtd->oobsize < ((ecc->bytes + 4) * nsectors)) { + ret = -EINVAL; + goto err; + } + + layout->eccbytes = (ecc->bytes * nsectors); + + ecc->layout = layout; + ecc->priv = data; + + return 0; + +err: + kfree(data); + + return ret; +} + +static void sunxi_nand_hw_common_ecc_ctrl_cleanup(struct nand_ecc_ctrl *ecc) +{ + kfree(ecc->priv); +} + +static int sunxi_nand_hw_ecc_ctrl_init(struct mtd_info *mtd, + struct nand_ecc_ctrl *ecc, + struct device_node *np) +{ + struct nand_ecclayout *layout; + int nsectors; + int i, j; + int ret; + + ret = sunxi_nand_hw_common_ecc_ctrl_init(mtd, ecc, np); + if (ret) + return ret; + + ecc->read_page = sunxi_nfc_hw_ecc_read_page; + ecc->write_page = sunxi_nfc_hw_ecc_write_page; + layout = ecc->layout; + nsectors = mtd->writesize / ecc->size; + + for (i = 0; i < nsectors; i++) { + if (i) { + layout->oobfree[i].offset = + layout->oobfree[i - 1].offset + + layout->oobfree[i - 1].length + + ecc->bytes; + layout->oobfree[i].length = 4; + } else { + /* + * The first 2 bytes are used for BB markers, hence we + * only have 2 bytes available in the first user data + * section. + */ + layout->oobfree[i].length = 2; + layout->oobfree[i].offset = 2; + } + + for (j = 0; j < ecc->bytes; j++) + layout->eccpos[(ecc->bytes * i) + j] = + layout->oobfree[i].offset + + layout->oobfree[i].length + j; + } + + if (mtd->oobsize > (ecc->bytes + 4) * nsectors) { + layout->oobfree[nsectors].offset = + layout->oobfree[nsectors - 1].offset + + layout->oobfree[nsectors - 1].length + + ecc->bytes; + layout->oobfree[nsectors].length = mtd->oobsize - + ((ecc->bytes + 4) * nsectors); + } + + return 0; +} + +static int sunxi_nand_hw_syndrome_ecc_ctrl_init(struct mtd_info *mtd, + struct nand_ecc_ctrl *ecc, + struct device_node *np) +{ + struct nand_ecclayout *layout; + int nsectors; + int i; + int ret; + + ret = sunxi_nand_hw_common_ecc_ctrl_init(mtd, ecc, np); + if (ret) + return ret; + + ecc->prepad = 4; + ecc->read_page = sunxi_nfc_hw_syndrome_ecc_read_page; + ecc->write_page = sunxi_nfc_hw_syndrome_ecc_write_page; + + layout = ecc->layout; + nsectors = mtd->writesize / ecc->size; + + for (i = 0; i < (ecc->bytes * nsectors); i++) + layout->eccpos[i] = i; + + layout->oobfree[0].length = mtd->oobsize - i; + layout->oobfree[0].offset = i; + + return 0; +} + +static void sunxi_nand_ecc_cleanup(struct nand_ecc_ctrl *ecc) +{ + switch (ecc->mode) { + case NAND_ECC_HW: + case NAND_ECC_HW_SYNDROME: + sunxi_nand_hw_common_ecc_ctrl_cleanup(ecc); + break; + case NAND_ECC_NONE: + kfree(ecc->layout); + default: + break; + } +} + +static int sunxi_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc, + struct device_node *np) +{ + struct nand_chip *nand = mtd->priv; + int strength; + int blk_size; + int ret; + + blk_size = of_get_nand_ecc_step_size(np); + strength = of_get_nand_ecc_strength(np); + if (blk_size > 0 && strength > 0) { + ecc->size = blk_size; + ecc->strength = strength; + } else { + ecc->size = nand->ecc_step_ds; + ecc->strength = nand->ecc_strength_ds; + } + + if (!ecc->size || !ecc->strength) + return -EINVAL; + + ecc->mode = NAND_ECC_HW; + + ret = of_get_nand_ecc_mode(np); + if (ret >= 0) + ecc->mode = ret; + + switch (ecc->mode) { + case NAND_ECC_SOFT_BCH: + break; + case NAND_ECC_HW: + ret = sunxi_nand_hw_ecc_ctrl_init(mtd, ecc, np); + if (ret) + return ret; + break; + case NAND_ECC_HW_SYNDROME: + ret = sunxi_nand_hw_syndrome_ecc_ctrl_init(mtd, ecc, np); + if (ret) + return ret; + break; + case NAND_ECC_NONE: + ecc->layout = kzalloc(sizeof(*ecc->layout), GFP_KERNEL); + if (!ecc->layout) + return -ENOMEM; + ecc->layout->oobfree[0].length = mtd->oobsize; + case NAND_ECC_SOFT: + break; + default: + return -EINVAL; + } + + return 0; +} + +static int sunxi_nand_chip_init(struct device *dev, struct sunxi_nfc *nfc, + struct device_node *np) +{ + const struct nand_sdr_timings *timings; + struct sunxi_nand_chip *chip; + struct mtd_part_parser_data ppdata; + struct mtd_info *mtd; + struct nand_chip *nand; + int nsels; + int ret; + int i; + u32 tmp; + + if (!of_get_property(np, "reg", &nsels)) + return -EINVAL; + + nsels /= sizeof(u32); + if (!nsels) { + dev_err(dev, "invalid reg property size\n"); + return -EINVAL; + } + + chip = devm_kzalloc(dev, + sizeof(*chip) + + (nsels * sizeof(struct sunxi_nand_chip_sel)), + GFP_KERNEL); + if (!chip) { + dev_err(dev, "could not allocate chip\n"); + return -ENOMEM; + } + + chip->nsels = nsels; + chip->selected = -1; + + for (i = 0; i < nsels; i++) { + ret = of_property_read_u32_index(np, "reg", i, &tmp); + if (ret) { + dev_err(dev, "could not retrieve reg property: %d\n", + ret); + return ret; + } + + if (tmp > NFC_MAX_CS) { + dev_err(dev, + "invalid reg value: %u (max CS = 7)\n", + tmp); + return -EINVAL; + } + + if (test_and_set_bit(tmp, &nfc->assigned_cs)) { + dev_err(dev, "CS %d already assigned\n", tmp); + return -EINVAL; + } + + chip->sels[i].cs = tmp; + + if (!of_property_read_u32_index(np, "allwinner,rb", i, &tmp) && + tmp < 2) { + chip->sels[i].rb.type = RB_NATIVE; + chip->sels[i].rb.info.nativeid = tmp; + } else { + ret = of_get_named_gpio(np, "rb-gpios", i); + if (ret >= 0) { + tmp = ret; + chip->sels[i].rb.type = RB_GPIO; + chip->sels[i].rb.info.gpio = tmp; + ret = devm_gpio_request(dev, tmp, "nand-rb"); + if (ret) + return ret; + + ret = gpio_direction_input(tmp); + if (ret) + return ret; + } else { + chip->sels[i].rb.type = RB_NONE; + } + } + } + + timings = onfi_async_timing_mode_to_sdr_timings(0); + if (IS_ERR(timings)) { + ret = PTR_ERR(timings); + dev_err(dev, + "could not retrieve timings for ONFI mode 0: %d\n", + ret); + return ret; + } + + ret = sunxi_nand_chip_set_timings(chip, timings); + if (ret) { + dev_err(dev, "could not configure chip timings: %d\n", ret); + return ret; + } + + nand = &chip->nand; + /* Default tR value specified in the ONFI spec (chapter 4.15.1) */ + nand->chip_delay = 200; + nand->controller = &nfc->controller; + nand->select_chip = sunxi_nfc_select_chip; + nand->cmd_ctrl = sunxi_nfc_cmd_ctrl; + nand->read_buf = sunxi_nfc_read_buf; + nand->write_buf = sunxi_nfc_write_buf; + nand->read_byte = sunxi_nfc_read_byte; + + if (of_get_nand_on_flash_bbt(np)) + nand->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; + + mtd = &chip->mtd; + mtd->dev.parent = dev; + mtd->priv = nand; + mtd->owner = THIS_MODULE; + + ret = nand_scan_ident(mtd, nsels, NULL); + if (ret) + return ret; + + ret = sunxi_nand_chip_init_timings(chip, np); + if (ret) { + dev_err(dev, "could not configure chip timings: %d\n", ret); + return ret; + } + + ret = sunxi_nand_ecc_init(mtd, &nand->ecc, np); + if (ret) { + dev_err(dev, "ECC init failed: %d\n", ret); + return ret; + } + + ret = nand_scan_tail(mtd); + if (ret) { + dev_err(dev, "nand_scan_tail failed: %d\n", ret); + return ret; + } + + ppdata.of_node = np; + ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (ret) { + dev_err(dev, "failed to register mtd device: %d\n", ret); + nand_release(mtd); + return ret; + } + + list_add_tail(&chip->node, &nfc->chips); + + return 0; +} + +static int sunxi_nand_chips_init(struct device *dev, struct sunxi_nfc *nfc) +{ + struct device_node *np = dev->of_node; + struct device_node *nand_np; + int nchips = of_get_child_count(np); + int ret; + + if (nchips > 8) { + dev_err(dev, "too many NAND chips: %d (max = 8)\n", nchips); + return -EINVAL; + } + + for_each_child_of_node(np, nand_np) { + ret = sunxi_nand_chip_init(dev, nfc, nand_np); + if (ret) + return ret; + } + + return 0; +} + +static void sunxi_nand_chips_cleanup(struct sunxi_nfc *nfc) +{ + struct sunxi_nand_chip *chip; + + while (!list_empty(&nfc->chips)) { + chip = list_first_entry(&nfc->chips, struct sunxi_nand_chip, + node); + nand_release(&chip->mtd); + sunxi_nand_ecc_cleanup(&chip->nand.ecc); + } +} + +static int sunxi_nfc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *r; + struct sunxi_nfc *nfc; + int irq; + int ret; + + nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL); + if (!nfc) + return -ENOMEM; + + nfc->dev = dev; + spin_lock_init(&nfc->controller.lock); + init_waitqueue_head(&nfc->controller.wq); + INIT_LIST_HEAD(&nfc->chips); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nfc->regs = devm_ioremap_resource(dev, r); + if (IS_ERR(nfc->regs)) + return PTR_ERR(nfc->regs); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "failed to retrieve irq\n"); + return irq; + } + + nfc->ahb_clk = devm_clk_get(dev, "ahb"); + if (IS_ERR(nfc->ahb_clk)) { + dev_err(dev, "failed to retrieve ahb clk\n"); + return PTR_ERR(nfc->ahb_clk); + } + + ret = clk_prepare_enable(nfc->ahb_clk); + if (ret) + return ret; + + nfc->mod_clk = devm_clk_get(dev, "mod"); + if (IS_ERR(nfc->mod_clk)) { + dev_err(dev, "failed to retrieve mod clk\n"); + ret = PTR_ERR(nfc->mod_clk); + goto out_ahb_clk_unprepare; + } + + ret = clk_prepare_enable(nfc->mod_clk); + if (ret) + goto out_ahb_clk_unprepare; + + ret = sunxi_nfc_rst(nfc); + if (ret) + goto out_mod_clk_unprepare; + + writel(0, nfc->regs + NFC_REG_INT); + ret = devm_request_irq(dev, irq, sunxi_nfc_interrupt, + 0, "sunxi-nand", nfc); + if (ret) + goto out_mod_clk_unprepare; + + platform_set_drvdata(pdev, nfc); + + /* + * TODO: replace these magic values with proper flags as soon as we + * know what they are encoding. + */ + writel(0x100, nfc->regs + NFC_REG_TIMING_CTL); + writel(0x7ff, nfc->regs + NFC_REG_TIMING_CFG); + + ret = sunxi_nand_chips_init(dev, nfc); + if (ret) { + dev_err(dev, "failed to init nand chips\n"); + goto out_mod_clk_unprepare; + } + + return 0; + +out_mod_clk_unprepare: + clk_disable_unprepare(nfc->mod_clk); +out_ahb_clk_unprepare: + clk_disable_unprepare(nfc->ahb_clk); + + return ret; +} + +static int sunxi_nfc_remove(struct platform_device *pdev) +{ + struct sunxi_nfc *nfc = platform_get_drvdata(pdev); + + sunxi_nand_chips_cleanup(nfc); + + return 0; +} + +static const struct of_device_id sunxi_nfc_ids[] = { + { .compatible = "allwinner,sun4i-a10-nand" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, sunxi_nfc_ids); + +static struct platform_driver sunxi_nfc_driver = { + .driver = { + .name = "sunxi_nand", + .of_match_table = sunxi_nfc_ids, + }, + .probe = sunxi_nfc_probe, + .remove = sunxi_nfc_remove, +}; +module_platform_driver(sunxi_nfc_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Boris BREZILLON"); +MODULE_DESCRIPTION("Allwinner NAND Flash Controller driver"); +MODULE_ALIAS("platform:sunxi_nand"); diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c new file mode 100644 index 000000000..fb8fd35fa --- /dev/null +++ b/drivers/mtd/nand/tmio_nand.c @@ -0,0 +1,508 @@ +/* + * Toshiba TMIO NAND flash controller driver + * + * Slightly murky pre-git history of the driver: + * + * Copyright (c) Ian Molton 2004, 2005, 2008 + * Original work, independent of sharps code. Included hardware ECC support. + * Hard ECC did not work for writes in the early revisions. + * Copyright (c) Dirk Opfer 2005. + * Modifications developed from sharps code but + * NOT containing any, ported onto Ians base. + * Copyright (c) Chris Humbert 2005 + * Copyright (c) Dmitry Baryshkov 2008 + * Minor fixes + * + * Parts copyright Sebastian Carlier + * + * This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + */ + + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/mfd/core.h> +#include <linux/mfd/tmio.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/slab.h> + +/*--------------------------------------------------------------------------*/ + +/* + * NAND Flash Host Controller Configuration Register + */ +#define CCR_COMMAND 0x04 /* w Command */ +#define CCR_BASE 0x10 /* l NAND Flash Control Reg Base Addr */ +#define CCR_INTP 0x3d /* b Interrupt Pin */ +#define CCR_INTE 0x48 /* b Interrupt Enable */ +#define CCR_EC 0x4a /* b Event Control */ +#define CCR_ICC 0x4c /* b Internal Clock Control */ +#define CCR_ECCC 0x5b /* b ECC Control */ +#define CCR_NFTC 0x60 /* b NAND Flash Transaction Control */ +#define CCR_NFM 0x61 /* b NAND Flash Monitor */ +#define CCR_NFPSC 0x62 /* b NAND Flash Power Supply Control */ +#define CCR_NFDC 0x63 /* b NAND Flash Detect Control */ + +/* + * NAND Flash Control Register + */ +#define FCR_DATA 0x00 /* bwl Data Register */ +#define FCR_MODE 0x04 /* b Mode Register */ +#define FCR_STATUS 0x05 /* b Status Register */ +#define FCR_ISR 0x06 /* b Interrupt Status Register */ +#define FCR_IMR 0x07 /* b Interrupt Mask Register */ + +/* FCR_MODE Register Command List */ +#define FCR_MODE_DATA 0x94 /* Data Data_Mode */ +#define FCR_MODE_COMMAND 0x95 /* Data Command_Mode */ +#define FCR_MODE_ADDRESS 0x96 /* Data Address_Mode */ + +#define FCR_MODE_HWECC_CALC 0xB4 /* HW-ECC Data */ +#define FCR_MODE_HWECC_RESULT 0xD4 /* HW-ECC Calc result Read_Mode */ +#define FCR_MODE_HWECC_RESET 0xF4 /* HW-ECC Reset */ + +#define FCR_MODE_POWER_ON 0x0C /* Power Supply ON to SSFDC card */ +#define FCR_MODE_POWER_OFF 0x08 /* Power Supply OFF to SSFDC card */ + +#define FCR_MODE_LED_OFF 0x00 /* LED OFF */ +#define FCR_MODE_LED_ON 0x04 /* LED ON */ + +#define FCR_MODE_EJECT_ON 0x68 /* Ejection events active */ +#define FCR_MODE_EJECT_OFF 0x08 /* Ejection events ignored */ + +#define FCR_MODE_LOCK 0x6C /* Lock_Mode. Eject Switch Invalid */ +#define FCR_MODE_UNLOCK 0x0C /* UnLock_Mode. Eject Switch is valid */ + +#define FCR_MODE_CONTROLLER_ID 0x40 /* Controller ID Read */ +#define FCR_MODE_STANDBY 0x00 /* SSFDC card Changes Standby State */ + +#define FCR_MODE_WE 0x80 +#define FCR_MODE_ECC1 0x40 +#define FCR_MODE_ECC0 0x20 +#define FCR_MODE_CE 0x10 +#define FCR_MODE_PCNT1 0x08 +#define FCR_MODE_PCNT0 0x04 +#define FCR_MODE_ALE 0x02 +#define FCR_MODE_CLE 0x01 + +#define FCR_STATUS_BUSY 0x80 + +/*--------------------------------------------------------------------------*/ + +struct tmio_nand { + struct mtd_info mtd; + struct nand_chip chip; + + struct platform_device *dev; + + void __iomem *ccr; + void __iomem *fcr; + unsigned long fcr_base; + + unsigned int irq; + + /* for tmio_nand_read_byte */ + u8 read; + unsigned read_good:1; +}; + +#define mtd_to_tmio(m) container_of(m, struct tmio_nand, mtd) + + +/*--------------------------------------------------------------------------*/ + +static void tmio_nand_hwcontrol(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + struct nand_chip *chip = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + u8 mode; + + if (ctrl & NAND_NCE) { + mode = FCR_MODE_DATA; + + if (ctrl & NAND_CLE) + mode |= FCR_MODE_CLE; + else + mode &= ~FCR_MODE_CLE; + + if (ctrl & NAND_ALE) + mode |= FCR_MODE_ALE; + else + mode &= ~FCR_MODE_ALE; + } else { + mode = FCR_MODE_STANDBY; + } + + tmio_iowrite8(mode, tmio->fcr + FCR_MODE); + tmio->read_good = 0; + } + + if (cmd != NAND_CMD_NONE) + tmio_iowrite8(cmd, chip->IO_ADDR_W); +} + +static int tmio_nand_dev_ready(struct mtd_info *mtd) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + + return !(tmio_ioread8(tmio->fcr + FCR_STATUS) & FCR_STATUS_BUSY); +} + +static irqreturn_t tmio_irq(int irq, void *__tmio) +{ + struct tmio_nand *tmio = __tmio; + struct nand_chip *nand_chip = &tmio->chip; + + /* disable RDYREQ interrupt */ + tmio_iowrite8(0x00, tmio->fcr + FCR_IMR); + + if (unlikely(!waitqueue_active(&nand_chip->controller->wq))) + dev_warn(&tmio->dev->dev, "spurious interrupt\n"); + + wake_up(&nand_chip->controller->wq); + return IRQ_HANDLED; +} + +/* + *The TMIO core has a RDYREQ interrupt on the posedge of #SMRB. + *This interrupt is normally disabled, but for long operations like + *erase and write, we enable it to wake us up. The irq handler + *disables the interrupt. + */ +static int +tmio_nand_wait(struct mtd_info *mtd, struct nand_chip *nand_chip) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + long timeout; + + /* enable RDYREQ interrupt */ + tmio_iowrite8(0x0f, tmio->fcr + FCR_ISR); + tmio_iowrite8(0x81, tmio->fcr + FCR_IMR); + + timeout = wait_event_timeout(nand_chip->controller->wq, + tmio_nand_dev_ready(mtd), + msecs_to_jiffies(nand_chip->state == FL_ERASING ? 400 : 20)); + + if (unlikely(!tmio_nand_dev_ready(mtd))) { + tmio_iowrite8(0x00, tmio->fcr + FCR_IMR); + dev_warn(&tmio->dev->dev, "still busy with %s after %d ms\n", + nand_chip->state == FL_ERASING ? "erase" : "program", + nand_chip->state == FL_ERASING ? 400 : 20); + + } else if (unlikely(!timeout)) { + tmio_iowrite8(0x00, tmio->fcr + FCR_IMR); + dev_warn(&tmio->dev->dev, "timeout waiting for interrupt\n"); + } + + nand_chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + return nand_chip->read_byte(mtd); +} + +/* + *The TMIO controller combines two 8-bit data bytes into one 16-bit + *word. This function separates them so nand_base.c works as expected, + *especially its NAND_CMD_READID routines. + * + *To prevent stale data from being read, tmio_nand_hwcontrol() clears + *tmio->read_good. + */ +static u_char tmio_nand_read_byte(struct mtd_info *mtd) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + unsigned int data; + + if (tmio->read_good--) + return tmio->read; + + data = tmio_ioread16(tmio->fcr + FCR_DATA); + tmio->read = data >> 8; + return data; +} + +/* + *The TMIO controller converts an 8-bit NAND interface to a 16-bit + *bus interface, so all data reads and writes must be 16-bit wide. + *Thus, we implement 16-bit versions of the read, write, and verify + *buffer functions. + */ +static void +tmio_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + + tmio_iowrite16_rep(tmio->fcr + FCR_DATA, buf, len >> 1); +} + +static void tmio_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + + tmio_ioread16_rep(tmio->fcr + FCR_DATA, buf, len >> 1); +} + +static void tmio_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + + tmio_iowrite8(FCR_MODE_HWECC_RESET, tmio->fcr + FCR_MODE); + tmio_ioread8(tmio->fcr + FCR_DATA); /* dummy read */ + tmio_iowrite8(FCR_MODE_HWECC_CALC, tmio->fcr + FCR_MODE); +} + +static int tmio_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct tmio_nand *tmio = mtd_to_tmio(mtd); + unsigned int ecc; + + tmio_iowrite8(FCR_MODE_HWECC_RESULT, tmio->fcr + FCR_MODE); + + ecc = tmio_ioread16(tmio->fcr + FCR_DATA); + ecc_code[1] = ecc; /* 000-255 LP7-0 */ + ecc_code[0] = ecc >> 8; /* 000-255 LP15-8 */ + ecc = tmio_ioread16(tmio->fcr + FCR_DATA); + ecc_code[2] = ecc; /* 000-255 CP5-0,11b */ + ecc_code[4] = ecc >> 8; /* 256-511 LP7-0 */ + ecc = tmio_ioread16(tmio->fcr + FCR_DATA); + ecc_code[3] = ecc; /* 256-511 LP15-8 */ + ecc_code[5] = ecc >> 8; /* 256-511 CP5-0,11b */ + + tmio_iowrite8(FCR_MODE_DATA, tmio->fcr + FCR_MODE); + return 0; +} + +static int tmio_nand_correct_data(struct mtd_info *mtd, unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc) +{ + int r0, r1; + + /* assume ecc.size = 512 and ecc.bytes = 6 */ + r0 = __nand_correct_data(buf, read_ecc, calc_ecc, 256); + if (r0 < 0) + return r0; + r1 = __nand_correct_data(buf + 256, read_ecc + 3, calc_ecc + 3, 256); + if (r1 < 0) + return r1; + return r0 + r1; +} + +static int tmio_hw_init(struct platform_device *dev, struct tmio_nand *tmio) +{ + const struct mfd_cell *cell = mfd_get_cell(dev); + int ret; + + if (cell->enable) { + ret = cell->enable(dev); + if (ret) + return ret; + } + + /* (4Ch) CLKRUN Enable 1st spcrunc */ + tmio_iowrite8(0x81, tmio->ccr + CCR_ICC); + + /* (10h)BaseAddress 0x1000 spba.spba2 */ + tmio_iowrite16(tmio->fcr_base, tmio->ccr + CCR_BASE); + tmio_iowrite16(tmio->fcr_base >> 16, tmio->ccr + CCR_BASE + 2); + + /* (04h)Command Register I/O spcmd */ + tmio_iowrite8(0x02, tmio->ccr + CCR_COMMAND); + + /* (62h) Power Supply Control ssmpwc */ + /* HardPowerOFF - SuspendOFF - PowerSupplyWait_4MS */ + tmio_iowrite8(0x02, tmio->ccr + CCR_NFPSC); + + /* (63h) Detect Control ssmdtc */ + tmio_iowrite8(0x02, tmio->ccr + CCR_NFDC); + + /* Interrupt status register clear sintst */ + tmio_iowrite8(0x0f, tmio->fcr + FCR_ISR); + + /* After power supply, Media are reset smode */ + tmio_iowrite8(FCR_MODE_POWER_ON, tmio->fcr + FCR_MODE); + tmio_iowrite8(FCR_MODE_COMMAND, tmio->fcr + FCR_MODE); + tmio_iowrite8(NAND_CMD_RESET, tmio->fcr + FCR_DATA); + + /* Standby Mode smode */ + tmio_iowrite8(FCR_MODE_STANDBY, tmio->fcr + FCR_MODE); + + mdelay(5); + + return 0; +} + +static void tmio_hw_stop(struct platform_device *dev, struct tmio_nand *tmio) +{ + const struct mfd_cell *cell = mfd_get_cell(dev); + + tmio_iowrite8(FCR_MODE_POWER_OFF, tmio->fcr + FCR_MODE); + if (cell->disable) + cell->disable(dev); +} + +static int tmio_probe(struct platform_device *dev) +{ + struct tmio_nand_data *data = dev_get_platdata(&dev->dev); + struct resource *fcr = platform_get_resource(dev, + IORESOURCE_MEM, 0); + struct resource *ccr = platform_get_resource(dev, + IORESOURCE_MEM, 1); + int irq = platform_get_irq(dev, 0); + struct tmio_nand *tmio; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + int retval; + + if (data == NULL) + dev_warn(&dev->dev, "NULL platform data!\n"); + + tmio = devm_kzalloc(&dev->dev, sizeof(*tmio), GFP_KERNEL); + if (!tmio) + return -ENOMEM; + + tmio->dev = dev; + + platform_set_drvdata(dev, tmio); + mtd = &tmio->mtd; + nand_chip = &tmio->chip; + mtd->priv = nand_chip; + mtd->name = "tmio-nand"; + + tmio->ccr = devm_ioremap(&dev->dev, ccr->start, resource_size(ccr)); + if (!tmio->ccr) + return -EIO; + + tmio->fcr_base = fcr->start & 0xfffff; + tmio->fcr = devm_ioremap(&dev->dev, fcr->start, resource_size(fcr)); + if (!tmio->fcr) + return -EIO; + + retval = tmio_hw_init(dev, tmio); + if (retval) + return retval; + + /* Set address of NAND IO lines */ + nand_chip->IO_ADDR_R = tmio->fcr; + nand_chip->IO_ADDR_W = tmio->fcr; + + /* Set address of hardware control function */ + nand_chip->cmd_ctrl = tmio_nand_hwcontrol; + nand_chip->dev_ready = tmio_nand_dev_ready; + nand_chip->read_byte = tmio_nand_read_byte; + nand_chip->write_buf = tmio_nand_write_buf; + nand_chip->read_buf = tmio_nand_read_buf; + + /* set eccmode using hardware ECC */ + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 6; + nand_chip->ecc.strength = 2; + nand_chip->ecc.hwctl = tmio_nand_enable_hwecc; + nand_chip->ecc.calculate = tmio_nand_calculate_ecc; + nand_chip->ecc.correct = tmio_nand_correct_data; + + if (data) + nand_chip->badblock_pattern = data->badblock_pattern; + + /* 15 us command delay time */ + nand_chip->chip_delay = 15; + + retval = devm_request_irq(&dev->dev, irq, &tmio_irq, 0, + dev_name(&dev->dev), tmio); + if (retval) { + dev_err(&dev->dev, "request_irq error %d\n", retval); + goto err_irq; + } + + tmio->irq = irq; + nand_chip->waitfunc = tmio_nand_wait; + + /* Scan to find existence of the device */ + if (nand_scan(mtd, 1)) { + retval = -ENODEV; + goto err_irq; + } + /* Register the partitions */ + retval = mtd_device_parse_register(mtd, NULL, NULL, + data ? data->partition : NULL, + data ? data->num_partitions : 0); + if (!retval) + return retval; + + nand_release(mtd); + +err_irq: + tmio_hw_stop(dev, tmio); + return retval; +} + +static int tmio_remove(struct platform_device *dev) +{ + struct tmio_nand *tmio = platform_get_drvdata(dev); + + nand_release(&tmio->mtd); + tmio_hw_stop(dev, tmio); + return 0; +} + +#ifdef CONFIG_PM +static int tmio_suspend(struct platform_device *dev, pm_message_t state) +{ + const struct mfd_cell *cell = mfd_get_cell(dev); + + if (cell->suspend) + cell->suspend(dev); + + tmio_hw_stop(dev, platform_get_drvdata(dev)); + return 0; +} + +static int tmio_resume(struct platform_device *dev) +{ + const struct mfd_cell *cell = mfd_get_cell(dev); + + /* FIXME - is this required or merely another attack of the broken + * SHARP platform? Looks suspicious. + */ + tmio_hw_init(dev, platform_get_drvdata(dev)); + + if (cell->resume) + cell->resume(dev); + + return 0; +} +#else +#define tmio_suspend NULL +#define tmio_resume NULL +#endif + +static struct platform_driver tmio_driver = { + .driver.name = "tmio-nand", + .driver.owner = THIS_MODULE, + .probe = tmio_probe, + .remove = tmio_remove, + .suspend = tmio_suspend, + .resume = tmio_resume, +}; + +module_platform_driver(tmio_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Ian Molton, Dirk Opfer, Chris Humbert, Dmitry Baryshkov"); +MODULE_DESCRIPTION("NAND flash driver on Toshiba Mobile IO controller"); +MODULE_ALIAS("platform:tmio-nand"); diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/txx9ndfmc.c new file mode 100644 index 000000000..9c0bc45e2 --- /dev/null +++ b/drivers/mtd/nand/txx9ndfmc.c @@ -0,0 +1,427 @@ +/* + * TXx9 NAND flash memory controller driver + * Based on RBTX49xx patch from CELF patch archive. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * (C) Copyright TOSHIBA CORPORATION 2004-2007 + * All Rights Reserved. + */ +#include <linux/err.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/nand_ecc.h> +#include <linux/mtd/partitions.h> +#include <linux/io.h> +#include <asm/txx9/ndfmc.h> + +/* TXX9 NDFMC Registers */ +#define TXX9_NDFDTR 0x00 +#define TXX9_NDFMCR 0x04 +#define TXX9_NDFSR 0x08 +#define TXX9_NDFISR 0x0c +#define TXX9_NDFIMR 0x10 +#define TXX9_NDFSPR 0x14 +#define TXX9_NDFRSTR 0x18 /* not TX4939 */ + +/* NDFMCR : NDFMC Mode Control */ +#define TXX9_NDFMCR_WE 0x80 +#define TXX9_NDFMCR_ECC_ALL 0x60 +#define TXX9_NDFMCR_ECC_RESET 0x60 +#define TXX9_NDFMCR_ECC_READ 0x40 +#define TXX9_NDFMCR_ECC_ON 0x20 +#define TXX9_NDFMCR_ECC_OFF 0x00 +#define TXX9_NDFMCR_CE 0x10 +#define TXX9_NDFMCR_BSPRT 0x04 /* TX4925/TX4926 only */ +#define TXX9_NDFMCR_ALE 0x02 +#define TXX9_NDFMCR_CLE 0x01 +/* TX4939 only */ +#define TXX9_NDFMCR_X16 0x0400 +#define TXX9_NDFMCR_DMAREQ_MASK 0x0300 +#define TXX9_NDFMCR_DMAREQ_NODMA 0x0000 +#define TXX9_NDFMCR_DMAREQ_128 0x0100 +#define TXX9_NDFMCR_DMAREQ_256 0x0200 +#define TXX9_NDFMCR_DMAREQ_512 0x0300 +#define TXX9_NDFMCR_CS_MASK 0x0c +#define TXX9_NDFMCR_CS(ch) ((ch) << 2) + +/* NDFMCR : NDFMC Status */ +#define TXX9_NDFSR_BUSY 0x80 +/* TX4939 only */ +#define TXX9_NDFSR_DMARUN 0x40 + +/* NDFMCR : NDFMC Reset */ +#define TXX9_NDFRSTR_RST 0x01 + +struct txx9ndfmc_priv { + struct platform_device *dev; + struct nand_chip chip; + struct mtd_info mtd; + int cs; + const char *mtdname; +}; + +#define MAX_TXX9NDFMC_DEV 4 +struct txx9ndfmc_drvdata { + struct mtd_info *mtds[MAX_TXX9NDFMC_DEV]; + void __iomem *base; + unsigned char hold; /* in gbusclock */ + unsigned char spw; /* in gbusclock */ + struct nand_hw_control hw_control; +}; + +static struct platform_device *mtd_to_platdev(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + struct txx9ndfmc_priv *txx9_priv = chip->priv; + return txx9_priv->dev; +} + +static void __iomem *ndregaddr(struct platform_device *dev, unsigned int reg) +{ + struct txx9ndfmc_drvdata *drvdata = platform_get_drvdata(dev); + struct txx9ndfmc_platform_data *plat = dev_get_platdata(&dev->dev); + + return drvdata->base + (reg << plat->shift); +} + +static u32 txx9ndfmc_read(struct platform_device *dev, unsigned int reg) +{ + return __raw_readl(ndregaddr(dev, reg)); +} + +static void txx9ndfmc_write(struct platform_device *dev, + u32 val, unsigned int reg) +{ + __raw_writel(val, ndregaddr(dev, reg)); +} + +static uint8_t txx9ndfmc_read_byte(struct mtd_info *mtd) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + + return txx9ndfmc_read(dev, TXX9_NDFDTR); +} + +static void txx9ndfmc_write_buf(struct mtd_info *mtd, const uint8_t *buf, + int len) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + void __iomem *ndfdtr = ndregaddr(dev, TXX9_NDFDTR); + u32 mcr = txx9ndfmc_read(dev, TXX9_NDFMCR); + + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_WE, TXX9_NDFMCR); + while (len--) + __raw_writel(*buf++, ndfdtr); + txx9ndfmc_write(dev, mcr, TXX9_NDFMCR); +} + +static void txx9ndfmc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + void __iomem *ndfdtr = ndregaddr(dev, TXX9_NDFDTR); + + while (len--) + *buf++ = __raw_readl(ndfdtr); +} + +static void txx9ndfmc_cmd_ctrl(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + struct txx9ndfmc_priv *txx9_priv = chip->priv; + struct platform_device *dev = txx9_priv->dev; + struct txx9ndfmc_platform_data *plat = dev_get_platdata(&dev->dev); + + if (ctrl & NAND_CTRL_CHANGE) { + u32 mcr = txx9ndfmc_read(dev, TXX9_NDFMCR); + + mcr &= ~(TXX9_NDFMCR_CLE | TXX9_NDFMCR_ALE | TXX9_NDFMCR_CE); + mcr |= ctrl & NAND_CLE ? TXX9_NDFMCR_CLE : 0; + mcr |= ctrl & NAND_ALE ? TXX9_NDFMCR_ALE : 0; + /* TXX9_NDFMCR_CE bit is 0:high 1:low */ + mcr |= ctrl & NAND_NCE ? TXX9_NDFMCR_CE : 0; + if (txx9_priv->cs >= 0 && (ctrl & NAND_NCE)) { + mcr &= ~TXX9_NDFMCR_CS_MASK; + mcr |= TXX9_NDFMCR_CS(txx9_priv->cs); + } + txx9ndfmc_write(dev, mcr, TXX9_NDFMCR); + } + if (cmd != NAND_CMD_NONE) + txx9ndfmc_write(dev, cmd & 0xff, TXX9_NDFDTR); + if (plat->flags & NDFMC_PLAT_FLAG_DUMMYWRITE) { + /* dummy write to update external latch */ + if ((ctrl & NAND_CTRL_CHANGE) && cmd == NAND_CMD_NONE) + txx9ndfmc_write(dev, 0, TXX9_NDFDTR); + } + mmiowb(); +} + +static int txx9ndfmc_dev_ready(struct mtd_info *mtd) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + + return !(txx9ndfmc_read(dev, TXX9_NDFSR) & TXX9_NDFSR_BUSY); +} + +static int txx9ndfmc_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat, + uint8_t *ecc_code) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + struct nand_chip *chip = mtd->priv; + int eccbytes; + u32 mcr = txx9ndfmc_read(dev, TXX9_NDFMCR); + + mcr &= ~TXX9_NDFMCR_ECC_ALL; + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_OFF, TXX9_NDFMCR); + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_READ, TXX9_NDFMCR); + for (eccbytes = chip->ecc.bytes; eccbytes > 0; eccbytes -= 3) { + ecc_code[1] = txx9ndfmc_read(dev, TXX9_NDFDTR); + ecc_code[0] = txx9ndfmc_read(dev, TXX9_NDFDTR); + ecc_code[2] = txx9ndfmc_read(dev, TXX9_NDFDTR); + ecc_code += 3; + } + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_OFF, TXX9_NDFMCR); + return 0; +} + +static int txx9ndfmc_correct_data(struct mtd_info *mtd, unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc) +{ + struct nand_chip *chip = mtd->priv; + int eccsize; + int corrected = 0; + int stat; + + for (eccsize = chip->ecc.size; eccsize > 0; eccsize -= 256) { + stat = __nand_correct_data(buf, read_ecc, calc_ecc, 256); + if (stat < 0) + return stat; + corrected += stat; + buf += 256; + read_ecc += 3; + calc_ecc += 3; + } + return corrected; +} + +static void txx9ndfmc_enable_hwecc(struct mtd_info *mtd, int mode) +{ + struct platform_device *dev = mtd_to_platdev(mtd); + u32 mcr = txx9ndfmc_read(dev, TXX9_NDFMCR); + + mcr &= ~TXX9_NDFMCR_ECC_ALL; + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_RESET, TXX9_NDFMCR); + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_OFF, TXX9_NDFMCR); + txx9ndfmc_write(dev, mcr | TXX9_NDFMCR_ECC_ON, TXX9_NDFMCR); +} + +static void txx9ndfmc_initialize(struct platform_device *dev) +{ + struct txx9ndfmc_platform_data *plat = dev_get_platdata(&dev->dev); + struct txx9ndfmc_drvdata *drvdata = platform_get_drvdata(dev); + int tmout = 100; + + if (plat->flags & NDFMC_PLAT_FLAG_NO_RSTR) + ; /* no NDFRSTR. Write to NDFSPR resets the NDFMC. */ + else { + /* reset NDFMC */ + txx9ndfmc_write(dev, + txx9ndfmc_read(dev, TXX9_NDFRSTR) | + TXX9_NDFRSTR_RST, + TXX9_NDFRSTR); + while (txx9ndfmc_read(dev, TXX9_NDFRSTR) & TXX9_NDFRSTR_RST) { + if (--tmout == 0) { + dev_err(&dev->dev, "reset failed.\n"); + break; + } + udelay(1); + } + } + /* setup Hold Time, Strobe Pulse Width */ + txx9ndfmc_write(dev, (drvdata->hold << 4) | drvdata->spw, TXX9_NDFSPR); + txx9ndfmc_write(dev, + (plat->flags & NDFMC_PLAT_FLAG_USE_BSPRT) ? + TXX9_NDFMCR_BSPRT : 0, TXX9_NDFMCR); +} + +#define TXX9NDFMC_NS_TO_CYC(gbusclk, ns) \ + DIV_ROUND_UP((ns) * DIV_ROUND_UP(gbusclk, 1000), 1000000) + +static int txx9ndfmc_nand_scan(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + int ret; + + ret = nand_scan_ident(mtd, 1, NULL); + if (!ret) { + if (mtd->writesize >= 512) { + /* Hardware ECC 6 byte ECC per 512 Byte data */ + chip->ecc.size = 512; + chip->ecc.bytes = 6; + } + ret = nand_scan_tail(mtd); + } + return ret; +} + +static int __init txx9ndfmc_probe(struct platform_device *dev) +{ + struct txx9ndfmc_platform_data *plat = dev_get_platdata(&dev->dev); + int hold, spw; + int i; + struct txx9ndfmc_drvdata *drvdata; + unsigned long gbusclk = plat->gbus_clock; + struct resource *res; + + drvdata = devm_kzalloc(&dev->dev, sizeof(*drvdata), GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + res = platform_get_resource(dev, IORESOURCE_MEM, 0); + drvdata->base = devm_ioremap_resource(&dev->dev, res); + if (IS_ERR(drvdata->base)) + return PTR_ERR(drvdata->base); + + hold = plat->hold ?: 20; /* tDH */ + spw = plat->spw ?: 90; /* max(tREADID, tWP, tRP) */ + + hold = TXX9NDFMC_NS_TO_CYC(gbusclk, hold); + spw = TXX9NDFMC_NS_TO_CYC(gbusclk, spw); + if (plat->flags & NDFMC_PLAT_FLAG_HOLDADD) + hold -= 2; /* actual hold time : (HOLD + 2) BUSCLK */ + spw -= 1; /* actual wait time : (SPW + 1) BUSCLK */ + hold = clamp(hold, 1, 15); + drvdata->hold = hold; + spw = clamp(spw, 1, 15); + drvdata->spw = spw; + dev_info(&dev->dev, "CLK:%ldMHz HOLD:%d SPW:%d\n", + (gbusclk + 500000) / 1000000, hold, spw); + + spin_lock_init(&drvdata->hw_control.lock); + init_waitqueue_head(&drvdata->hw_control.wq); + + platform_set_drvdata(dev, drvdata); + txx9ndfmc_initialize(dev); + + for (i = 0; i < MAX_TXX9NDFMC_DEV; i++) { + struct txx9ndfmc_priv *txx9_priv; + struct nand_chip *chip; + struct mtd_info *mtd; + + if (!(plat->ch_mask & (1 << i))) + continue; + txx9_priv = kzalloc(sizeof(struct txx9ndfmc_priv), + GFP_KERNEL); + if (!txx9_priv) + continue; + chip = &txx9_priv->chip; + mtd = &txx9_priv->mtd; + mtd->owner = THIS_MODULE; + + mtd->priv = chip; + + chip->read_byte = txx9ndfmc_read_byte; + chip->read_buf = txx9ndfmc_read_buf; + chip->write_buf = txx9ndfmc_write_buf; + chip->cmd_ctrl = txx9ndfmc_cmd_ctrl; + chip->dev_ready = txx9ndfmc_dev_ready; + chip->ecc.calculate = txx9ndfmc_calculate_ecc; + chip->ecc.correct = txx9ndfmc_correct_data; + chip->ecc.hwctl = txx9ndfmc_enable_hwecc; + chip->ecc.mode = NAND_ECC_HW; + /* txx9ndfmc_nand_scan will overwrite ecc.size and ecc.bytes */ + chip->ecc.size = 256; + chip->ecc.bytes = 3; + chip->ecc.strength = 1; + chip->chip_delay = 100; + chip->controller = &drvdata->hw_control; + + chip->priv = txx9_priv; + txx9_priv->dev = dev; + + if (plat->ch_mask != 1) { + txx9_priv->cs = i; + txx9_priv->mtdname = kasprintf(GFP_KERNEL, "%s.%u", + dev_name(&dev->dev), i); + } else { + txx9_priv->cs = -1; + txx9_priv->mtdname = kstrdup(dev_name(&dev->dev), + GFP_KERNEL); + } + if (!txx9_priv->mtdname) { + kfree(txx9_priv); + dev_err(&dev->dev, "Unable to allocate MTD name.\n"); + continue; + } + if (plat->wide_mask & (1 << i)) + chip->options |= NAND_BUSWIDTH_16; + + if (txx9ndfmc_nand_scan(mtd)) { + kfree(txx9_priv->mtdname); + kfree(txx9_priv); + continue; + } + mtd->name = txx9_priv->mtdname; + + mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); + drvdata->mtds[i] = mtd; + } + + return 0; +} + +static int __exit txx9ndfmc_remove(struct platform_device *dev) +{ + struct txx9ndfmc_drvdata *drvdata = platform_get_drvdata(dev); + int i; + + if (!drvdata) + return 0; + for (i = 0; i < MAX_TXX9NDFMC_DEV; i++) { + struct mtd_info *mtd = drvdata->mtds[i]; + struct nand_chip *chip; + struct txx9ndfmc_priv *txx9_priv; + + if (!mtd) + continue; + chip = mtd->priv; + txx9_priv = chip->priv; + + nand_release(mtd); + kfree(txx9_priv->mtdname); + kfree(txx9_priv); + } + return 0; +} + +#ifdef CONFIG_PM +static int txx9ndfmc_resume(struct platform_device *dev) +{ + if (platform_get_drvdata(dev)) + txx9ndfmc_initialize(dev); + return 0; +} +#else +#define txx9ndfmc_resume NULL +#endif + +static struct platform_driver txx9ndfmc_driver = { + .remove = __exit_p(txx9ndfmc_remove), + .resume = txx9ndfmc_resume, + .driver = { + .name = "txx9ndfmc", + }, +}; + +module_platform_driver_probe(txx9ndfmc_driver, txx9ndfmc_probe); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("TXx9 SoC NAND flash controller driver"); +MODULE_ALIAS("platform:txx9ndfmc"); diff --git a/drivers/mtd/nand/xway_nand.c b/drivers/mtd/nand/xway_nand.c new file mode 100644 index 000000000..3f81dc8f2 --- /dev/null +++ b/drivers/mtd/nand/xway_nand.c @@ -0,0 +1,201 @@ +/* + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + * + * Copyright © 2012 John Crispin <blogic@openwrt.org> + */ + +#include <linux/mtd/nand.h> +#include <linux/of_gpio.h> +#include <linux/of_platform.h> + +#include <lantiq_soc.h> + +/* nand registers */ +#define EBU_ADDSEL1 0x24 +#define EBU_NAND_CON 0xB0 +#define EBU_NAND_WAIT 0xB4 +#define EBU_NAND_ECC0 0xB8 +#define EBU_NAND_ECC_AC 0xBC + +/* nand commands */ +#define NAND_CMD_ALE (1 << 2) +#define NAND_CMD_CLE (1 << 3) +#define NAND_CMD_CS (1 << 4) +#define NAND_WRITE_CMD_RESET 0xff +#define NAND_WRITE_CMD (NAND_CMD_CS | NAND_CMD_CLE) +#define NAND_WRITE_ADDR (NAND_CMD_CS | NAND_CMD_ALE) +#define NAND_WRITE_DATA (NAND_CMD_CS) +#define NAND_READ_DATA (NAND_CMD_CS) +#define NAND_WAIT_WR_C (1 << 3) +#define NAND_WAIT_RD (0x1) + +/* we need to tel the ebu which addr we mapped the nand to */ +#define ADDSEL1_MASK(x) (x << 4) +#define ADDSEL1_REGEN 1 + +/* we need to tell the EBU that we have nand attached and set it up properly */ +#define BUSCON1_SETUP (1 << 22) +#define BUSCON1_BCGEN_RES (0x3 << 12) +#define BUSCON1_WAITWRC2 (2 << 8) +#define BUSCON1_WAITRDC2 (2 << 6) +#define BUSCON1_HOLDC1 (1 << 4) +#define BUSCON1_RECOVC1 (1 << 2) +#define BUSCON1_CMULT4 1 + +#define NAND_CON_CE (1 << 20) +#define NAND_CON_OUT_CS1 (1 << 10) +#define NAND_CON_IN_CS1 (1 << 8) +#define NAND_CON_PRE_P (1 << 7) +#define NAND_CON_WP_P (1 << 6) +#define NAND_CON_SE_P (1 << 5) +#define NAND_CON_CS_P (1 << 4) +#define NAND_CON_CSMUX (1 << 1) +#define NAND_CON_NANDM 1 + +static void xway_reset_chip(struct nand_chip *chip) +{ + unsigned long nandaddr = (unsigned long) chip->IO_ADDR_W; + unsigned long flags; + + nandaddr &= ~NAND_WRITE_ADDR; + nandaddr |= NAND_WRITE_CMD; + + /* finish with a reset */ + spin_lock_irqsave(&ebu_lock, flags); + writeb(NAND_WRITE_CMD_RESET, (void __iomem *) nandaddr); + while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0) + ; + spin_unlock_irqrestore(&ebu_lock, flags); +} + +static void xway_select_chip(struct mtd_info *mtd, int chip) +{ + + switch (chip) { + case -1: + ltq_ebu_w32_mask(NAND_CON_CE, 0, EBU_NAND_CON); + ltq_ebu_w32_mask(NAND_CON_NANDM, 0, EBU_NAND_CON); + break; + case 0: + ltq_ebu_w32_mask(0, NAND_CON_NANDM, EBU_NAND_CON); + ltq_ebu_w32_mask(0, NAND_CON_CE, EBU_NAND_CON); + break; + default: + BUG(); + } +} + +static void xway_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *this = mtd->priv; + unsigned long nandaddr = (unsigned long) this->IO_ADDR_W; + unsigned long flags; + + if (ctrl & NAND_CTRL_CHANGE) { + nandaddr &= ~(NAND_WRITE_CMD | NAND_WRITE_ADDR); + if (ctrl & NAND_CLE) + nandaddr |= NAND_WRITE_CMD; + else + nandaddr |= NAND_WRITE_ADDR; + this->IO_ADDR_W = (void __iomem *) nandaddr; + } + + if (cmd != NAND_CMD_NONE) { + spin_lock_irqsave(&ebu_lock, flags); + writeb(cmd, this->IO_ADDR_W); + while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0) + ; + spin_unlock_irqrestore(&ebu_lock, flags); + } +} + +static int xway_dev_ready(struct mtd_info *mtd) +{ + return ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_RD; +} + +static unsigned char xway_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + unsigned long nandaddr = (unsigned long) this->IO_ADDR_R; + unsigned long flags; + int ret; + + spin_lock_irqsave(&ebu_lock, flags); + ret = ltq_r8((void __iomem *)(nandaddr + NAND_READ_DATA)); + spin_unlock_irqrestore(&ebu_lock, flags); + + return ret; +} + +static int xway_nand_probe(struct platform_device *pdev) +{ + struct nand_chip *this = platform_get_drvdata(pdev); + unsigned long nandaddr = (unsigned long) this->IO_ADDR_W; + const __be32 *cs = of_get_property(pdev->dev.of_node, + "lantiq,cs", NULL); + u32 cs_flag = 0; + + /* load our CS from the DT. Either we find a valid 1 or default to 0 */ + if (cs && (*cs == 1)) + cs_flag = NAND_CON_IN_CS1 | NAND_CON_OUT_CS1; + + /* setup the EBU to run in NAND mode on our base addr */ + ltq_ebu_w32(CPHYSADDR(nandaddr) + | ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1); + + ltq_ebu_w32(BUSCON1_SETUP | BUSCON1_BCGEN_RES | BUSCON1_WAITWRC2 + | BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1 + | BUSCON1_CMULT4, LTQ_EBU_BUSCON1); + + ltq_ebu_w32(NAND_CON_NANDM | NAND_CON_CSMUX | NAND_CON_CS_P + | NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P + | cs_flag, EBU_NAND_CON); + + /* finish with a reset */ + xway_reset_chip(this); + + return 0; +} + +/* allow users to override the partition in DT using the cmdline */ +static const char *part_probes[] = { "cmdlinepart", "ofpart", NULL }; + +static struct platform_nand_data xway_nand_data = { + .chip = { + .nr_chips = 1, + .chip_delay = 30, + .part_probe_types = part_probes, + }, + .ctrl = { + .probe = xway_nand_probe, + .cmd_ctrl = xway_cmd_ctrl, + .dev_ready = xway_dev_ready, + .select_chip = xway_select_chip, + .read_byte = xway_read_byte, + } +}; + +/* + * Try to find the node inside the DT. If it is available attach out + * platform_nand_data + */ +static int __init xway_register_nand(void) +{ + struct device_node *node; + struct platform_device *pdev; + + node = of_find_compatible_node(NULL, NULL, "lantiq,nand-xway"); + if (!node) + return -ENOENT; + pdev = of_find_device_by_node(node); + if (!pdev) + return -EINVAL; + pdev->dev.platform_data = &xway_nand_data; + of_node_put(node); + return 0; +} + +subsys_initcall(xway_register_nand); |