summaryrefslogtreecommitdiff
path: root/drivers/net/can/sja1000
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/can/sja1000')
-rw-r--r--drivers/net/can/sja1000/Kconfig103
-rw-r--r--drivers/net/can/sja1000/Makefile14
-rw-r--r--drivers/net/can/sja1000/ems_pci.c372
-rw-r--r--drivers/net/can/sja1000/ems_pcmcia.c320
-rw-r--r--drivers/net/can/sja1000/kvaser_pci.c396
-rw-r--r--drivers/net/can/sja1000/peak_pci.c765
-rw-r--r--drivers/net/can/sja1000/peak_pcmcia.c744
-rw-r--r--drivers/net/can/sja1000/plx_pci.c650
-rw-r--r--drivers/net/can/sja1000/sja1000.c704
-rw-r--r--drivers/net/can/sja1000/sja1000.h182
-rw-r--r--drivers/net/can/sja1000/sja1000_isa.c323
-rw-r--r--drivers/net/can/sja1000/sja1000_platform.c260
-rw-r--r--drivers/net/can/sja1000/tscan1.c216
13 files changed, 5049 insertions, 0 deletions
diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig
new file mode 100644
index 000000000..1e65cb6c2
--- /dev/null
+++ b/drivers/net/can/sja1000/Kconfig
@@ -0,0 +1,103 @@
+menuconfig CAN_SJA1000
+ tristate "Philips/NXP SJA1000 devices"
+ depends on HAS_IOMEM
+
+if CAN_SJA1000
+
+config CAN_SJA1000_ISA
+ tristate "ISA Bus based legacy SJA1000 driver"
+ ---help---
+ This driver adds legacy support for SJA1000 chips connected to
+ the ISA bus using I/O port, memory mapped or indirect access.
+
+config CAN_SJA1000_PLATFORM
+ tristate "Generic Platform Bus based SJA1000 driver"
+ ---help---
+ This driver adds support for the SJA1000 chips connected to
+ the "platform bus" (Linux abstraction for directly to the
+ processor attached devices). Which can be found on various
+ boards from Phytec (http://www.phytec.de) like the PCM027,
+ PCM038. It also provides the OpenFirmware "platform bus" found
+ on embedded systems with OpenFirmware bindings, e.g. if you
+ have a PowerPC based system you may want to enable this option.
+
+config CAN_EMS_PCMCIA
+ tristate "EMS CPC-CARD Card"
+ depends on PCMCIA
+ ---help---
+ This driver is for the one or two channel CPC-CARD cards from
+ EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+
+config CAN_EMS_PCI
+ tristate "EMS CPC-PCI, CPC-PCIe and CPC-104P Card"
+ depends on PCI
+ ---help---
+ This driver is for the one, two or four channel CPC-PCI,
+ CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
+ (http://www.ems-wuensche.de).
+
+config CAN_PEAK_PCMCIA
+ tristate "PEAK PCAN-PC Card"
+ depends on PCMCIA
+ depends on HAS_IOPORT_MAP
+ ---help---
+ This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels)
+ from PEAK-System (http://www.peak-system.com). To compile this
+ driver as a module, choose M here: the module will be called
+ peak_pcmcia.
+
+config CAN_PEAK_PCI
+ tristate "PEAK PCAN-PCI/PCIe/miniPCI Cards"
+ depends on PCI
+ ---help---
+ This driver is for the PCAN-PCI/PCIe/miniPCI cards
+ (1, 2, 3 or 4 channels) from PEAK-System Technik
+ (http://www.peak-system.com).
+
+config CAN_PEAK_PCIEC
+ bool "PEAK PCAN-ExpressCard Cards"
+ depends on CAN_PEAK_PCI
+ select I2C
+ select I2C_ALGOBIT
+ default y
+ ---help---
+ Say Y here if you want to use a PCAN-ExpressCard from PEAK-System
+ Technik. This will also automatically select I2C and I2C_ALGO
+ configuration options.
+
+config CAN_KVASER_PCI
+ tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
+ depends on PCI
+ ---help---
+ This driver is for the PCIcanx and PCIcan cards (1, 2 or
+ 4 channel) from Kvaser (http://www.kvaser.com).
+
+config CAN_PLX_PCI
+ tristate "PLX90xx PCI-bridge based Cards"
+ depends on PCI
+ ---help---
+ This driver is for CAN interface cards based on
+ the PLX90xx PCI bridge.
+ Driver supports now:
+ - Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/)
+ - Adlink PCI-7841/cPCI-7841 SE card
+ - esd CAN-PCI/CPCI/PCI104/200 (http://www.esd.eu/)
+ - esd CAN-PCI/PMC/266
+ - esd CAN-PCIe/2000
+ - Marathon CAN-bus-PCI card (http://www.marathon.ru/)
+ - TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)
+ - IXXAT Automation PC-I 04/PCI card (http://www.ixxat.com/)
+ - Connect Tech Inc. CANpro/104-Plus Opto (CRG001) card (http://www.connecttech.com)
+
+config CAN_TSCAN1
+ tristate "TS-CAN1 PC104 boards"
+ depends on ISA
+ help
+ This driver is for Technologic Systems' TSCAN-1 PC104 boards.
+ http://www.embeddedarm.com/products/board-detail.php?product=TS-CAN1
+ The driver supports multiple boards and automatically configures them:
+ PLD IO base addresses are read from jumpers JP1 and JP2,
+ IRQ numbers are read from jumpers JP4 and JP5,
+ SJA1000 IO base addresses are chosen heuristically (first that works).
+
+endif
diff --git a/drivers/net/can/sja1000/Makefile b/drivers/net/can/sja1000/Makefile
new file mode 100644
index 000000000..be11ddd11
--- /dev/null
+++ b/drivers/net/can/sja1000/Makefile
@@ -0,0 +1,14 @@
+#
+# Makefile for the SJA1000 CAN controller drivers.
+#
+
+obj-$(CONFIG_CAN_SJA1000) += sja1000.o
+obj-$(CONFIG_CAN_SJA1000_ISA) += sja1000_isa.o
+obj-$(CONFIG_CAN_SJA1000_PLATFORM) += sja1000_platform.o
+obj-$(CONFIG_CAN_EMS_PCMCIA) += ems_pcmcia.o
+obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o
+obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o
+obj-$(CONFIG_CAN_PEAK_PCMCIA) += peak_pcmcia.o
+obj-$(CONFIG_CAN_PEAK_PCI) += peak_pci.o
+obj-$(CONFIG_CAN_PLX_PCI) += plx_pci.o
+obj-$(CONFIG_CAN_TSCAN1) += tscan1.o
diff --git a/drivers/net/can/sja1000/ems_pci.c b/drivers/net/can/sja1000/ems_pci.c
new file mode 100644
index 000000000..7481c324a
--- /dev/null
+++ b/drivers/net/can/sja1000/ems_pci.c
@@ -0,0 +1,372 @@
+/*
+ * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
+ * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
+ * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/can/dev.h>
+#include <linux/io.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "ems_pci"
+
+MODULE_AUTHOR("Sebastian Haas <haas@ems-wuenche.com>");
+MODULE_DESCRIPTION("Socket-CAN driver for EMS CPC-PCI/PCIe/104P CAN cards");
+MODULE_SUPPORTED_DEVICE("EMS CPC-PCI/PCIe/104P CAN card");
+MODULE_LICENSE("GPL v2");
+
+#define EMS_PCI_V1_MAX_CHAN 2
+#define EMS_PCI_V2_MAX_CHAN 4
+#define EMS_PCI_MAX_CHAN EMS_PCI_V2_MAX_CHAN
+
+struct ems_pci_card {
+ int version;
+ int channels;
+
+ struct pci_dev *pci_dev;
+ struct net_device *net_dev[EMS_PCI_MAX_CHAN];
+
+ void __iomem *conf_addr;
+ void __iomem *base_addr;
+};
+
+#define EMS_PCI_CAN_CLOCK (16000000 / 2)
+
+/*
+ * Register definitions and descriptions are from LinCAN 0.3.3.
+ *
+ * PSB4610 PITA-2 bridge control registers
+ */
+#define PITA2_ICR 0x00 /* Interrupt Control Register */
+#define PITA2_ICR_INT0 0x00000002 /* [RC] INT0 Active/Clear */
+#define PITA2_ICR_INT0_EN 0x00020000 /* [RW] Enable INT0 */
+
+#define PITA2_MISC 0x1c /* Miscellaneous Register */
+#define PITA2_MISC_CONFIG 0x04000000 /* Multiplexed parallel interface */
+
+/*
+ * Register definitions for the PLX 9030
+ */
+#define PLX_ICSR 0x4c /* Interrupt Control/Status register */
+#define PLX_ICSR_LINTI1_ENA 0x0001 /* LINTi1 Enable */
+#define PLX_ICSR_PCIINT_ENA 0x0040 /* PCI Interrupt Enable */
+#define PLX_ICSR_LINTI1_CLR 0x0400 /* Local Edge Triggerable Interrupt Clear */
+#define PLX_ICSR_ENA_CLR (PLX_ICSR_LINTI1_ENA | PLX_ICSR_PCIINT_ENA | \
+ PLX_ICSR_LINTI1_CLR)
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode, push-pull and the correct polarity.
+ */
+#define EMS_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 7
+ * (meaning direct oscillator output) because the second SJA1000 chip
+ * is driven by the first one CLKOUT output.
+ */
+#define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+
+#define EMS_PCI_V1_BASE_BAR 1
+#define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */
+#define EMS_PCI_V2_BASE_BAR 2
+#define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */
+#define EMS_PCI_CAN_BASE_OFFSET 0x400 /* offset where the controllers starts */
+#define EMS_PCI_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
+
+#define EMS_PCI_BASE_SIZE 4096 /* size of controller area */
+
+static const struct pci_device_id ems_pci_tbl[] = {
+ /* CPC-PCI v1 */
+ {PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
+ /* CPC-PCI v2 */
+ {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4000},
+ /* CPC-104P v2 */
+ {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4002},
+ {0,}
+};
+MODULE_DEVICE_TABLE(pci, ems_pci_tbl);
+
+/*
+ * Helper to read internal registers from card logic (not CAN)
+ */
+static u8 ems_pci_v1_readb(struct ems_pci_card *card, unsigned int port)
+{
+ return readb(card->base_addr + (port * 4));
+}
+
+static u8 ems_pci_v1_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return readb(priv->reg_base + (port * 4));
+}
+
+static void ems_pci_v1_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val)
+{
+ writeb(val, priv->reg_base + (port * 4));
+}
+
+static void ems_pci_v1_post_irq(const struct sja1000_priv *priv)
+{
+ struct ems_pci_card *card = (struct ems_pci_card *)priv->priv;
+
+ /* reset int flag of pita */
+ writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
+ card->conf_addr + PITA2_ICR);
+}
+
+static u8 ems_pci_v2_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return readb(priv->reg_base + port);
+}
+
+static void ems_pci_v2_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val)
+{
+ writeb(val, priv->reg_base + port);
+}
+
+static void ems_pci_v2_post_irq(const struct sja1000_priv *priv)
+{
+ struct ems_pci_card *card = (struct ems_pci_card *)priv->priv;
+
+ writel(PLX_ICSR_ENA_CLR, card->conf_addr + PLX_ICSR);
+}
+
+/*
+ * Check if a CAN controller is present at the specified location
+ * by trying to set 'em into the PeliCAN mode
+ */
+static inline int ems_pci_check_chan(const struct sja1000_priv *priv)
+{
+ unsigned char res;
+
+ /* Make sure SJA1000 is in reset mode */
+ priv->write_reg(priv, SJA1000_MOD, 1);
+
+ priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
+
+ /* read reset-values */
+ res = priv->read_reg(priv, SJA1000_CDR);
+
+ if (res == CDR_PELICAN)
+ return 1;
+
+ return 0;
+}
+
+static void ems_pci_del_card(struct pci_dev *pdev)
+{
+ struct ems_pci_card *card = pci_get_drvdata(pdev);
+ struct net_device *dev;
+ int i = 0;
+
+ for (i = 0; i < card->channels; i++) {
+ dev = card->net_dev[i];
+
+ if (!dev)
+ continue;
+
+ dev_info(&pdev->dev, "Removing %s.\n", dev->name);
+ unregister_sja1000dev(dev);
+ free_sja1000dev(dev);
+ }
+
+ if (card->base_addr != NULL)
+ pci_iounmap(card->pci_dev, card->base_addr);
+
+ if (card->conf_addr != NULL)
+ pci_iounmap(card->pci_dev, card->conf_addr);
+
+ kfree(card);
+
+ pci_disable_device(pdev);
+}
+
+static void ems_pci_card_reset(struct ems_pci_card *card)
+{
+ /* Request board reset */
+ writeb(0, card->base_addr);
+}
+
+/*
+ * Probe PCI device for EMS CAN signature and register each available
+ * CAN channel to SJA1000 Socket-CAN subsystem.
+ */
+static int ems_pci_add_card(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct sja1000_priv *priv;
+ struct net_device *dev;
+ struct ems_pci_card *card;
+ int max_chan, conf_size, base_bar;
+ int err, i;
+
+ /* Enabling PCI device */
+ if (pci_enable_device(pdev) < 0) {
+ dev_err(&pdev->dev, "Enabling PCI device failed\n");
+ return -ENODEV;
+ }
+
+ /* Allocating card structures to hold addresses, ... */
+ card = kzalloc(sizeof(struct ems_pci_card), GFP_KERNEL);
+ if (card == NULL) {
+ pci_disable_device(pdev);
+ return -ENOMEM;
+ }
+
+ pci_set_drvdata(pdev, card);
+
+ card->pci_dev = pdev;
+
+ card->channels = 0;
+
+ if (pdev->vendor == PCI_VENDOR_ID_PLX) {
+ card->version = 2; /* CPC-PCI v2 */
+ max_chan = EMS_PCI_V2_MAX_CHAN;
+ base_bar = EMS_PCI_V2_BASE_BAR;
+ conf_size = EMS_PCI_V2_CONF_SIZE;
+ } else {
+ card->version = 1; /* CPC-PCI v1 */
+ max_chan = EMS_PCI_V1_MAX_CHAN;
+ base_bar = EMS_PCI_V1_BASE_BAR;
+ conf_size = EMS_PCI_V1_CONF_SIZE;
+ }
+
+ /* Remap configuration space and controller memory area */
+ card->conf_addr = pci_iomap(pdev, 0, conf_size);
+ if (card->conf_addr == NULL) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
+ if (card->base_addr == NULL) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ if (card->version == 1) {
+ /* Configure PITA-2 parallel interface (enable MUX) */
+ writel(PITA2_MISC_CONFIG, card->conf_addr + PITA2_MISC);
+
+ /* Check for unique EMS CAN signature */
+ if (ems_pci_v1_readb(card, 0) != 0x55 ||
+ ems_pci_v1_readb(card, 1) != 0xAA ||
+ ems_pci_v1_readb(card, 2) != 0x01 ||
+ ems_pci_v1_readb(card, 3) != 0xCB ||
+ ems_pci_v1_readb(card, 4) != 0x11) {
+ dev_err(&pdev->dev,
+ "Not EMS Dr. Thomas Wuensche interface\n");
+ err = -ENODEV;
+ goto failure_cleanup;
+ }
+ }
+
+ ems_pci_card_reset(card);
+
+ /* Detect available channels */
+ for (i = 0; i < max_chan; i++) {
+ dev = alloc_sja1000dev(0);
+ if (dev == NULL) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ card->net_dev[i] = dev;
+ priv = netdev_priv(dev);
+ priv->priv = card;
+ priv->irq_flags = IRQF_SHARED;
+
+ dev->irq = pdev->irq;
+ priv->reg_base = card->base_addr + EMS_PCI_CAN_BASE_OFFSET
+ + (i * EMS_PCI_CAN_CTRL_SIZE);
+ if (card->version == 1) {
+ priv->read_reg = ems_pci_v1_read_reg;
+ priv->write_reg = ems_pci_v1_write_reg;
+ priv->post_irq = ems_pci_v1_post_irq;
+ } else {
+ priv->read_reg = ems_pci_v2_read_reg;
+ priv->write_reg = ems_pci_v2_write_reg;
+ priv->post_irq = ems_pci_v2_post_irq;
+ }
+
+ /* Check if channel is present */
+ if (ems_pci_check_chan(priv)) {
+ priv->can.clock.freq = EMS_PCI_CAN_CLOCK;
+ priv->ocr = EMS_PCI_OCR;
+ priv->cdr = EMS_PCI_CDR;
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = i;
+
+ if (card->version == 1)
+ /* reset int flag of pita */
+ writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
+ card->conf_addr + PITA2_ICR);
+ else
+ /* enable IRQ in PLX 9030 */
+ writel(PLX_ICSR_ENA_CLR,
+ card->conf_addr + PLX_ICSR);
+
+ /* Register SJA1000 device */
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "Registering device failed "
+ "(err=%d)\n", err);
+ free_sja1000dev(dev);
+ goto failure_cleanup;
+ }
+
+ card->channels++;
+
+ dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d\n",
+ i + 1, priv->reg_base, dev->irq);
+ } else {
+ free_sja1000dev(dev);
+ }
+ }
+
+ return 0;
+
+failure_cleanup:
+ dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
+
+ ems_pci_del_card(pdev);
+
+ return err;
+}
+
+static struct pci_driver ems_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = ems_pci_tbl,
+ .probe = ems_pci_add_card,
+ .remove = ems_pci_del_card,
+};
+
+module_pci_driver(ems_pci_driver);
diff --git a/drivers/net/can/sja1000/ems_pcmcia.c b/drivers/net/can/sja1000/ems_pcmcia.c
new file mode 100644
index 000000000..381de998d
--- /dev/null
+++ b/drivers/net/can/sja1000/ems_pcmcia.c
@@ -0,0 +1,320 @@
+/*
+ * Copyright (C) 2008 Sebastian Haas (initial chardev implementation)
+ * Copyright (C) 2010 Markus Plessing <plessing@ems-wuensche.com>
+ * Rework for mainline by Oliver Hartkopp <socketcan@hartkopp.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include "sja1000.h"
+
+#define DRV_NAME "ems_pcmcia"
+
+MODULE_AUTHOR("Markus Plessing <plessing@ems-wuensche.com>");
+MODULE_DESCRIPTION("Socket-CAN driver for EMS CPC-CARD cards");
+MODULE_SUPPORTED_DEVICE("EMS CPC-CARD CAN card");
+MODULE_LICENSE("GPL v2");
+
+#define EMS_PCMCIA_MAX_CHAN 2
+
+struct ems_pcmcia_card {
+ int channels;
+ struct pcmcia_device *pcmcia_dev;
+ struct net_device *net_dev[EMS_PCMCIA_MAX_CHAN];
+ void __iomem *base_addr;
+};
+
+#define EMS_PCMCIA_CAN_CLOCK (16000000 / 2)
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode , push-pull and the correct polarity.
+ */
+#define EMS_PCMCIA_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 7
+ * (meaning direct oscillator output) because the second SJA1000 chip
+ * is driven by the first one CLKOUT output.
+ */
+#define EMS_PCMCIA_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+#define EMS_PCMCIA_MEM_SIZE 4096 /* Size of the remapped io-memory */
+#define EMS_PCMCIA_CAN_BASE_OFFSET 0x100 /* Offset where controllers starts */
+#define EMS_PCMCIA_CAN_CTRL_SIZE 0x80 /* Memory size for each controller */
+
+#define EMS_CMD_RESET 0x00 /* Perform a reset of the card */
+#define EMS_CMD_MAP 0x03 /* Map CAN controllers into card' memory */
+#define EMS_CMD_UMAP 0x02 /* Unmap CAN controllers from card' memory */
+
+static struct pcmcia_device_id ems_pcmcia_tbl[] = {
+ PCMCIA_DEVICE_PROD_ID123("EMS_T_W", "CPC-Card", "V2.0", 0xeab1ea23,
+ 0xa338573f, 0xe4575800),
+ PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, ems_pcmcia_tbl);
+
+static u8 ems_pcmcia_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return readb(priv->reg_base + port);
+}
+
+static void ems_pcmcia_write_reg(const struct sja1000_priv *priv, int port,
+ u8 val)
+{
+ writeb(val, priv->reg_base + port);
+}
+
+static irqreturn_t ems_pcmcia_interrupt(int irq, void *dev_id)
+{
+ struct ems_pcmcia_card *card = dev_id;
+ struct net_device *dev;
+ irqreturn_t retval = IRQ_NONE;
+ int i, again;
+
+ /* Card not present */
+ if (readw(card->base_addr) != 0xAA55)
+ return IRQ_HANDLED;
+
+ do {
+ again = 0;
+
+ /* Check interrupt for each channel */
+ for (i = 0; i < card->channels; i++) {
+ dev = card->net_dev[i];
+ if (!dev)
+ continue;
+
+ if (sja1000_interrupt(irq, dev) == IRQ_HANDLED)
+ again = 1;
+ }
+ /* At least one channel handled the interrupt */
+ if (again)
+ retval = IRQ_HANDLED;
+
+ } while (again);
+
+ return retval;
+}
+
+/*
+ * Check if a CAN controller is present at the specified location
+ * by trying to set 'em into the PeliCAN mode
+ */
+static inline int ems_pcmcia_check_chan(struct sja1000_priv *priv)
+{
+ /* Make sure SJA1000 is in reset mode */
+ ems_pcmcia_write_reg(priv, SJA1000_MOD, 1);
+ ems_pcmcia_write_reg(priv, SJA1000_CDR, CDR_PELICAN);
+
+ /* read reset-values */
+ if (ems_pcmcia_read_reg(priv, SJA1000_CDR) == CDR_PELICAN)
+ return 1;
+
+ return 0;
+}
+
+static void ems_pcmcia_del_card(struct pcmcia_device *pdev)
+{
+ struct ems_pcmcia_card *card = pdev->priv;
+ struct net_device *dev;
+ int i;
+
+ free_irq(pdev->irq, card);
+
+ for (i = 0; i < card->channels; i++) {
+ dev = card->net_dev[i];
+ if (!dev)
+ continue;
+
+ printk(KERN_INFO "%s: removing %s on channel #%d\n",
+ DRV_NAME, dev->name, i);
+ unregister_sja1000dev(dev);
+ free_sja1000dev(dev);
+ }
+
+ writeb(EMS_CMD_UMAP, card->base_addr);
+ iounmap(card->base_addr);
+ kfree(card);
+
+ pdev->priv = NULL;
+}
+
+/*
+ * Probe PCI device for EMS CAN signature and register each available
+ * CAN channel to SJA1000 Socket-CAN subsystem.
+ */
+static int ems_pcmcia_add_card(struct pcmcia_device *pdev, unsigned long base)
+{
+ struct sja1000_priv *priv;
+ struct net_device *dev;
+ struct ems_pcmcia_card *card;
+ int err, i;
+
+ /* Allocating card structures to hold addresses, ... */
+ card = kzalloc(sizeof(struct ems_pcmcia_card), GFP_KERNEL);
+ if (!card)
+ return -ENOMEM;
+
+ pdev->priv = card;
+ card->channels = 0;
+
+ card->base_addr = ioremap(base, EMS_PCMCIA_MEM_SIZE);
+ if (!card->base_addr) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ /* Check for unique EMS CAN signature */
+ if (readw(card->base_addr) != 0xAA55) {
+ err = -ENODEV;
+ goto failure_cleanup;
+ }
+
+ /* Request board reset */
+ writeb(EMS_CMD_RESET, card->base_addr);
+
+ /* Make sure CAN controllers are mapped into card's memory space */
+ writeb(EMS_CMD_MAP, card->base_addr);
+
+ /* Detect available channels */
+ for (i = 0; i < EMS_PCMCIA_MAX_CHAN; i++) {
+ dev = alloc_sja1000dev(0);
+ if (!dev) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ card->net_dev[i] = dev;
+ priv = netdev_priv(dev);
+ priv->priv = card;
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = i;
+
+ priv->irq_flags = IRQF_SHARED;
+ dev->irq = pdev->irq;
+ priv->reg_base = card->base_addr + EMS_PCMCIA_CAN_BASE_OFFSET +
+ (i * EMS_PCMCIA_CAN_CTRL_SIZE);
+
+ /* Check if channel is present */
+ if (ems_pcmcia_check_chan(priv)) {
+ priv->read_reg = ems_pcmcia_read_reg;
+ priv->write_reg = ems_pcmcia_write_reg;
+ priv->can.clock.freq = EMS_PCMCIA_CAN_CLOCK;
+ priv->ocr = EMS_PCMCIA_OCR;
+ priv->cdr = EMS_PCMCIA_CDR;
+ priv->flags |= SJA1000_CUSTOM_IRQ_HANDLER;
+
+ /* Register SJA1000 device */
+ err = register_sja1000dev(dev);
+ if (err) {
+ free_sja1000dev(dev);
+ goto failure_cleanup;
+ }
+
+ card->channels++;
+
+ printk(KERN_INFO "%s: registered %s on channel "
+ "#%d at 0x%p, irq %d\n", DRV_NAME, dev->name,
+ i, priv->reg_base, dev->irq);
+ } else
+ free_sja1000dev(dev);
+ }
+
+ err = request_irq(dev->irq, &ems_pcmcia_interrupt, IRQF_SHARED,
+ DRV_NAME, card);
+ if (!err)
+ return 0;
+
+failure_cleanup:
+ ems_pcmcia_del_card(pdev);
+ return err;
+}
+
+/*
+ * Setup PCMCIA socket and probe for EMS CPC-CARD
+ */
+static int ems_pcmcia_probe(struct pcmcia_device *dev)
+{
+ int csval;
+
+ /* General socket configuration */
+ dev->config_flags |= CONF_ENABLE_IRQ;
+ dev->config_index = 1;
+ dev->config_regs = PRESENT_OPTION;
+
+ /* The io structure describes IO port mapping */
+ dev->resource[0]->end = 16;
+ dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
+ dev->resource[1]->end = 16;
+ dev->resource[1]->flags |= IO_DATA_PATH_WIDTH_16;
+ dev->io_lines = 5;
+
+ /* Allocate a memory window */
+ dev->resource[2]->flags =
+ (WIN_DATA_WIDTH_8 | WIN_MEMORY_TYPE_CM | WIN_ENABLE);
+ dev->resource[2]->start = dev->resource[2]->end = 0;
+
+ csval = pcmcia_request_window(dev, dev->resource[2], 0);
+ if (csval) {
+ dev_err(&dev->dev, "pcmcia_request_window failed (err=%d)\n",
+ csval);
+ return 0;
+ }
+
+ csval = pcmcia_map_mem_page(dev, dev->resource[2], dev->config_base);
+ if (csval) {
+ dev_err(&dev->dev, "pcmcia_map_mem_page failed (err=%d)\n",
+ csval);
+ return 0;
+ }
+
+ csval = pcmcia_enable_device(dev);
+ if (csval) {
+ dev_err(&dev->dev, "pcmcia_enable_device failed (err=%d)\n",
+ csval);
+ return 0;
+ }
+
+ ems_pcmcia_add_card(dev, dev->resource[2]->start);
+ return 0;
+}
+
+/*
+ * Release claimed resources
+ */
+static void ems_pcmcia_remove(struct pcmcia_device *dev)
+{
+ ems_pcmcia_del_card(dev);
+ pcmcia_disable_device(dev);
+}
+
+static struct pcmcia_driver ems_pcmcia_driver = {
+ .name = DRV_NAME,
+ .probe = ems_pcmcia_probe,
+ .remove = ems_pcmcia_remove,
+ .id_table = ems_pcmcia_tbl,
+};
+module_pcmcia_driver(ems_pcmcia_driver);
diff --git a/drivers/net/can/sja1000/kvaser_pci.c b/drivers/net/can/sja1000/kvaser_pci.c
new file mode 100644
index 000000000..15c00faee
--- /dev/null
+++ b/drivers/net/can/sja1000/kvaser_pci.c
@@ -0,0 +1,396 @@
+/*
+ * Copyright (C) 2008 Per Dalen <per.dalen@cnw.se>
+ *
+ * Parts of this software are based on (derived) the following:
+ *
+ * - Kvaser linux driver, version 4.72 BETA
+ * Copyright (C) 2002-2007 KVASER AB
+ *
+ * - Lincan driver, version 0.3.3, OCERA project
+ * Copyright (C) 2004 Pavel Pisa
+ * Copyright (C) 2001 Arnaud Westenberg
+ *
+ * - Socketcan SJA1000 drivers
+ * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
+ * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
+ * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
+ * 38106 Braunschweig, GERMANY
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/can/dev.h>
+#include <linux/io.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "kvaser_pci"
+
+MODULE_AUTHOR("Per Dalen <per.dalen@cnw.se>");
+MODULE_DESCRIPTION("Socket-CAN driver for KVASER PCAN PCI cards");
+MODULE_SUPPORTED_DEVICE("KVASER PCAN PCI CAN card");
+MODULE_LICENSE("GPL v2");
+
+#define MAX_NO_OF_CHANNELS 4 /* max no of channels on a single card */
+
+struct kvaser_pci {
+ int channel;
+ struct pci_dev *pci_dev;
+ struct net_device *slave_dev[MAX_NO_OF_CHANNELS-1];
+ void __iomem *conf_addr;
+ void __iomem *res_addr;
+ int no_channels;
+ u8 xilinx_ver;
+};
+
+#define KVASER_PCI_CAN_CLOCK (16000000 / 2)
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode , push-pull and the correct polarity.
+ */
+#define KVASER_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 0
+ * (meaning divide-by-2), the Pelican bit, and the clock-off bit
+ * (you will have no need for CLKOUT anyway).
+ */
+#define KVASER_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+
+/*
+ * These register values are valid for revision 14 of the Xilinx logic.
+ */
+#define XILINX_VERINT 7 /* Lower nibble simulate interrupts,
+ high nibble version number. */
+
+#define XILINX_PRESUMED_VERSION 14
+
+/*
+ * Important S5920 registers
+ */
+#define S5920_INTCSR 0x38
+#define S5920_PTCR 0x60
+#define INTCSR_ADDON_INTENABLE_M 0x2000
+
+
+#define KVASER_PCI_PORT_BYTES 0x20
+
+#define PCI_CONFIG_PORT_SIZE 0x80 /* size of the config io-memory */
+#define PCI_PORT_SIZE 0x80 /* size of a channel io-memory */
+#define PCI_PORT_XILINX_SIZE 0x08 /* size of a xilinx io-memory */
+
+#define KVASER_PCI_VENDOR_ID1 0x10e8 /* the PCI device and vendor IDs */
+#define KVASER_PCI_DEVICE_ID1 0x8406
+
+#define KVASER_PCI_VENDOR_ID2 0x1a07 /* the PCI device and vendor IDs */
+#define KVASER_PCI_DEVICE_ID2 0x0008
+
+static const struct pci_device_id kvaser_pci_tbl[] = {
+ {KVASER_PCI_VENDOR_ID1, KVASER_PCI_DEVICE_ID1, PCI_ANY_ID, PCI_ANY_ID,},
+ {KVASER_PCI_VENDOR_ID2, KVASER_PCI_DEVICE_ID2, PCI_ANY_ID, PCI_ANY_ID,},
+ { 0,}
+};
+
+MODULE_DEVICE_TABLE(pci, kvaser_pci_tbl);
+
+static u8 kvaser_pci_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return ioread8(priv->reg_base + port);
+}
+
+static void kvaser_pci_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val)
+{
+ iowrite8(val, priv->reg_base + port);
+}
+
+static void kvaser_pci_disable_irq(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct kvaser_pci *board = priv->priv;
+ u32 intcsr;
+
+ /* Disable interrupts from card */
+ intcsr = ioread32(board->conf_addr + S5920_INTCSR);
+ intcsr &= ~INTCSR_ADDON_INTENABLE_M;
+ iowrite32(intcsr, board->conf_addr + S5920_INTCSR);
+}
+
+static void kvaser_pci_enable_irq(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct kvaser_pci *board = priv->priv;
+ u32 tmp_en_io;
+
+ /* Enable interrupts from card */
+ tmp_en_io = ioread32(board->conf_addr + S5920_INTCSR);
+ tmp_en_io |= INTCSR_ADDON_INTENABLE_M;
+ iowrite32(tmp_en_io, board->conf_addr + S5920_INTCSR);
+}
+
+static int number_of_sja1000_chip(void __iomem *base_addr)
+{
+ u8 status;
+ int i;
+
+ for (i = 0; i < MAX_NO_OF_CHANNELS; i++) {
+ /* reset chip */
+ iowrite8(MOD_RM, base_addr +
+ (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
+ status = ioread8(base_addr +
+ (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
+ /* check reset bit */
+ if (!(status & MOD_RM))
+ break;
+ }
+
+ return i;
+}
+
+static void kvaser_pci_del_chan(struct net_device *dev)
+{
+ struct sja1000_priv *priv;
+ struct kvaser_pci *board;
+ int i;
+
+ if (!dev)
+ return;
+ priv = netdev_priv(dev);
+ board = priv->priv;
+ if (!board)
+ return;
+
+ dev_info(&board->pci_dev->dev, "Removing device %s\n",
+ dev->name);
+
+ /* Disable PCI interrupts */
+ kvaser_pci_disable_irq(dev);
+
+ for (i = 0; i < board->no_channels - 1; i++) {
+ if (board->slave_dev[i]) {
+ dev_info(&board->pci_dev->dev, "Removing device %s\n",
+ board->slave_dev[i]->name);
+ unregister_sja1000dev(board->slave_dev[i]);
+ free_sja1000dev(board->slave_dev[i]);
+ }
+ }
+ unregister_sja1000dev(dev);
+
+ pci_iounmap(board->pci_dev, priv->reg_base);
+ pci_iounmap(board->pci_dev, board->conf_addr);
+ pci_iounmap(board->pci_dev, board->res_addr);
+
+ free_sja1000dev(dev);
+}
+
+static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel,
+ struct net_device **master_dev,
+ void __iomem *conf_addr,
+ void __iomem *res_addr,
+ void __iomem *base_addr)
+{
+ struct net_device *dev;
+ struct sja1000_priv *priv;
+ struct kvaser_pci *board;
+ int err;
+
+ dev = alloc_sja1000dev(sizeof(struct kvaser_pci));
+ if (dev == NULL)
+ return -ENOMEM;
+
+ priv = netdev_priv(dev);
+ board = priv->priv;
+
+ board->pci_dev = pdev;
+ board->channel = channel;
+
+ /* S5920 */
+ board->conf_addr = conf_addr;
+
+ /* XILINX board wide address */
+ board->res_addr = res_addr;
+
+ if (channel == 0) {
+ board->xilinx_ver =
+ ioread8(board->res_addr + XILINX_VERINT) >> 4;
+
+ /* Assert PTADR# - we're in passive mode so the other bits are
+ not important */
+ iowrite32(0x80808080UL, board->conf_addr + S5920_PTCR);
+
+ /* Enable interrupts from card */
+ kvaser_pci_enable_irq(dev);
+ } else {
+ struct sja1000_priv *master_priv = netdev_priv(*master_dev);
+ struct kvaser_pci *master_board = master_priv->priv;
+ master_board->slave_dev[channel - 1] = dev;
+ master_board->no_channels = channel + 1;
+ board->xilinx_ver = master_board->xilinx_ver;
+ }
+
+ priv->reg_base = base_addr + channel * KVASER_PCI_PORT_BYTES;
+
+ priv->read_reg = kvaser_pci_read_reg;
+ priv->write_reg = kvaser_pci_write_reg;
+
+ priv->can.clock.freq = KVASER_PCI_CAN_CLOCK;
+
+ priv->ocr = KVASER_PCI_OCR;
+ priv->cdr = KVASER_PCI_CDR;
+
+ priv->irq_flags = IRQF_SHARED;
+ dev->irq = pdev->irq;
+
+ dev_info(&pdev->dev, "reg_base=%p conf_addr=%p irq=%d\n",
+ priv->reg_base, board->conf_addr, dev->irq);
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = channel;
+
+ /* Register SJA1000 device */
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "Registering device failed (err=%d)\n",
+ err);
+ goto failure;
+ }
+
+ if (channel == 0)
+ *master_dev = dev;
+
+ return 0;
+
+failure:
+ kvaser_pci_del_chan(dev);
+ return err;
+}
+
+static int kvaser_pci_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ int err;
+ struct net_device *master_dev = NULL;
+ struct sja1000_priv *priv;
+ struct kvaser_pci *board;
+ int no_channels;
+ void __iomem *base_addr = NULL;
+ void __iomem *conf_addr = NULL;
+ void __iomem *res_addr = NULL;
+ int i;
+
+ dev_info(&pdev->dev, "initializing device %04x:%04x\n",
+ pdev->vendor, pdev->device);
+
+ err = pci_enable_device(pdev);
+ if (err)
+ goto failure;
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err)
+ goto failure_release_pci;
+
+ /* S5920 */
+ conf_addr = pci_iomap(pdev, 0, PCI_CONFIG_PORT_SIZE);
+ if (conf_addr == NULL) {
+ err = -ENODEV;
+ goto failure_release_regions;
+ }
+
+ /* XILINX board wide address */
+ res_addr = pci_iomap(pdev, 2, PCI_PORT_XILINX_SIZE);
+ if (res_addr == NULL) {
+ err = -ENOMEM;
+ goto failure_iounmap;
+ }
+
+ base_addr = pci_iomap(pdev, 1, PCI_PORT_SIZE);
+ if (base_addr == NULL) {
+ err = -ENOMEM;
+ goto failure_iounmap;
+ }
+
+ no_channels = number_of_sja1000_chip(base_addr);
+ if (no_channels == 0) {
+ err = -ENOMEM;
+ goto failure_iounmap;
+ }
+
+ for (i = 0; i < no_channels; i++) {
+ err = kvaser_pci_add_chan(pdev, i, &master_dev,
+ conf_addr, res_addr,
+ base_addr);
+ if (err)
+ goto failure_cleanup;
+ }
+
+ priv = netdev_priv(master_dev);
+ board = priv->priv;
+
+ dev_info(&pdev->dev, "xilinx version=%d number of channels=%d\n",
+ board->xilinx_ver, board->no_channels);
+
+ pci_set_drvdata(pdev, master_dev);
+ return 0;
+
+failure_cleanup:
+ kvaser_pci_del_chan(master_dev);
+
+failure_iounmap:
+ if (conf_addr != NULL)
+ pci_iounmap(pdev, conf_addr);
+ if (res_addr != NULL)
+ pci_iounmap(pdev, res_addr);
+ if (base_addr != NULL)
+ pci_iounmap(pdev, base_addr);
+
+failure_release_regions:
+ pci_release_regions(pdev);
+
+failure_release_pci:
+ pci_disable_device(pdev);
+
+failure:
+ return err;
+
+}
+
+static void kvaser_pci_remove_one(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+
+ kvaser_pci_del_chan(dev);
+
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+}
+
+static struct pci_driver kvaser_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = kvaser_pci_tbl,
+ .probe = kvaser_pci_init_one,
+ .remove = kvaser_pci_remove_one,
+};
+
+module_pci_driver(kvaser_pci_driver);
diff --git a/drivers/net/can/sja1000/peak_pci.c b/drivers/net/can/sja1000/peak_pci.c
new file mode 100644
index 000000000..e5fac3680
--- /dev/null
+++ b/drivers/net/can/sja1000/peak_pci.c
@@ -0,0 +1,765 @@
+/*
+ * Copyright (C) 2007, 2011 Wolfgang Grandegger <wg@grandegger.com>
+ * Copyright (C) 2012 Stephane Grosjean <s.grosjean@peak-system.com>
+ *
+ * Derived from the PCAN project file driver/src/pcan_pci.c:
+ *
+ * Copyright (C) 2001-2006 PEAK System-Technik GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+#include <linux/can.h>
+#include <linux/can/dev.h>
+
+#include "sja1000.h"
+
+MODULE_AUTHOR("Stephane Grosjean <s.grosjean@peak-system.com>");
+MODULE_DESCRIPTION("Socket-CAN driver for PEAK PCAN PCI family cards");
+MODULE_SUPPORTED_DEVICE("PEAK PCAN PCI/PCIe/PCIeC miniPCI CAN cards");
+MODULE_SUPPORTED_DEVICE("PEAK PCAN miniPCIe/cPCI PC/104+ PCI/104e CAN Cards");
+MODULE_LICENSE("GPL v2");
+
+#define DRV_NAME "peak_pci"
+
+struct peak_pciec_card;
+struct peak_pci_chan {
+ void __iomem *cfg_base; /* Common for all channels */
+ struct net_device *prev_dev; /* Chain of network devices */
+ u16 icr_mask; /* Interrupt mask for fast ack */
+ struct peak_pciec_card *pciec_card; /* only for PCIeC LEDs */
+};
+
+#define PEAK_PCI_CAN_CLOCK (16000000 / 2)
+
+#define PEAK_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+#define PEAK_PCI_OCR OCR_TX0_PUSHPULL
+
+/*
+ * Important PITA registers
+ */
+#define PITA_ICR 0x00 /* Interrupt control register */
+#define PITA_GPIOICR 0x18 /* GPIO interface control register */
+#define PITA_MISC 0x1C /* Miscellaneous register */
+
+#define PEAK_PCI_CFG_SIZE 0x1000 /* Size of the config PCI bar */
+#define PEAK_PCI_CHAN_SIZE 0x0400 /* Size used by the channel */
+
+#define PEAK_PCI_VENDOR_ID 0x001C /* The PCI device and vendor IDs */
+#define PEAK_PCI_DEVICE_ID 0x0001 /* for PCI/PCIe slot cards */
+#define PEAK_PCIEC_DEVICE_ID 0x0002 /* for ExpressCard slot cards */
+#define PEAK_PCIE_DEVICE_ID 0x0003 /* for nextgen PCIe slot cards */
+#define PEAK_CPCI_DEVICE_ID 0x0004 /* for nextgen cPCI slot cards */
+#define PEAK_MPCI_DEVICE_ID 0x0005 /* for nextgen miniPCI slot cards */
+#define PEAK_PC_104P_DEVICE_ID 0x0006 /* PCAN-PC/104+ cards */
+#define PEAK_PCI_104E_DEVICE_ID 0x0007 /* PCAN-PCI/104 Express cards */
+#define PEAK_MPCIE_DEVICE_ID 0x0008 /* The miniPCIe slot cards */
+#define PEAK_PCIE_OEM_ID 0x0009 /* PCAN-PCI Express OEM */
+#define PEAK_PCIEC34_DEVICE_ID 0x000A /* PCAN-PCI Express 34 (one channel) */
+
+#define PEAK_PCI_CHAN_MAX 4
+
+static const u16 peak_pci_icr_masks[PEAK_PCI_CHAN_MAX] = {
+ 0x02, 0x01, 0x40, 0x80
+};
+
+static const struct pci_device_id peak_pci_tbl[] = {
+ {PEAK_PCI_VENDOR_ID, PEAK_PCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_PCIE_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_MPCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_MPCIE_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_PC_104P_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_PCI_104E_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_CPCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+#ifdef CONFIG_CAN_PEAK_PCIEC
+ {PEAK_PCI_VENDOR_ID, PEAK_PCIEC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+ {PEAK_PCI_VENDOR_ID, PEAK_PCIEC34_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+#endif
+ {0,}
+};
+
+MODULE_DEVICE_TABLE(pci, peak_pci_tbl);
+
+#ifdef CONFIG_CAN_PEAK_PCIEC
+/*
+ * PCAN-ExpressCard needs I2C bit-banging configuration option.
+ */
+
+/* GPIOICR byte access offsets */
+#define PITA_GPOUT 0x18 /* GPx output value */
+#define PITA_GPIN 0x19 /* GPx input value */
+#define PITA_GPOEN 0x1A /* configure GPx as ouput pin */
+
+/* I2C GP bits */
+#define PITA_GPIN_SCL 0x01 /* Serial Clock Line */
+#define PITA_GPIN_SDA 0x04 /* Serial DAta line */
+
+#define PCA9553_1_SLAVEADDR (0xC4 >> 1)
+
+/* PCA9553 LS0 fields values */
+enum {
+ PCA9553_LOW,
+ PCA9553_HIGHZ,
+ PCA9553_PWM0,
+ PCA9553_PWM1
+};
+
+/* LEDs control */
+#define PCA9553_ON PCA9553_LOW
+#define PCA9553_OFF PCA9553_HIGHZ
+#define PCA9553_SLOW PCA9553_PWM0
+#define PCA9553_FAST PCA9553_PWM1
+
+#define PCA9553_LED(c) (1 << (c))
+#define PCA9553_LED_STATE(s, c) ((s) << ((c) << 1))
+
+#define PCA9553_LED_ON(c) PCA9553_LED_STATE(PCA9553_ON, c)
+#define PCA9553_LED_OFF(c) PCA9553_LED_STATE(PCA9553_OFF, c)
+#define PCA9553_LED_SLOW(c) PCA9553_LED_STATE(PCA9553_SLOW, c)
+#define PCA9553_LED_FAST(c) PCA9553_LED_STATE(PCA9553_FAST, c)
+#define PCA9553_LED_MASK(c) PCA9553_LED_STATE(0x03, c)
+
+#define PCA9553_LED_OFF_ALL (PCA9553_LED_OFF(0) | PCA9553_LED_OFF(1))
+
+#define PCA9553_LS0_INIT 0x40 /* initial value (!= from 0x00) */
+
+struct peak_pciec_chan {
+ struct net_device *netdev;
+ unsigned long prev_rx_bytes;
+ unsigned long prev_tx_bytes;
+};
+
+struct peak_pciec_card {
+ void __iomem *cfg_base; /* Common for all channels */
+ void __iomem *reg_base; /* first channel base address */
+ u8 led_cache; /* leds state cache */
+
+ /* PCIExpressCard i2c data */
+ struct i2c_algo_bit_data i2c_bit;
+ struct i2c_adapter led_chip;
+ struct delayed_work led_work; /* led delayed work */
+ int chan_count;
+ struct peak_pciec_chan channel[PEAK_PCI_CHAN_MAX];
+};
+
+/* "normal" pci register write callback is overloaded for leds control */
+static void peak_pci_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val);
+
+static inline void pita_set_scl_highz(struct peak_pciec_card *card)
+{
+ u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SCL;
+ writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static inline void pita_set_sda_highz(struct peak_pciec_card *card)
+{
+ u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SDA;
+ writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static void peak_pciec_init_pita_gpio(struct peak_pciec_card *card)
+{
+ /* raise SCL & SDA GPIOs to high-Z */
+ pita_set_scl_highz(card);
+ pita_set_sda_highz(card);
+}
+
+static void pita_setsda(void *data, int state)
+{
+ struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+ u8 gp_out, gp_outen;
+
+ /* set output sda always to 0 */
+ gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SDA;
+ writeb(gp_out, card->cfg_base + PITA_GPOUT);
+
+ /* control output sda with GPOEN */
+ gp_outen = readb(card->cfg_base + PITA_GPOEN);
+ if (state)
+ gp_outen &= ~PITA_GPIN_SDA;
+ else
+ gp_outen |= PITA_GPIN_SDA;
+
+ writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static void pita_setscl(void *data, int state)
+{
+ struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+ u8 gp_out, gp_outen;
+
+ /* set output scl always to 0 */
+ gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SCL;
+ writeb(gp_out, card->cfg_base + PITA_GPOUT);
+
+ /* control output scl with GPOEN */
+ gp_outen = readb(card->cfg_base + PITA_GPOEN);
+ if (state)
+ gp_outen &= ~PITA_GPIN_SCL;
+ else
+ gp_outen |= PITA_GPIN_SCL;
+
+ writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static int pita_getsda(void *data)
+{
+ struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+
+ /* set tristate */
+ pita_set_sda_highz(card);
+
+ return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SDA) ? 1 : 0;
+}
+
+static int pita_getscl(void *data)
+{
+ struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+
+ /* set tristate */
+ pita_set_scl_highz(card);
+
+ return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SCL) ? 1 : 0;
+}
+
+/*
+ * write commands to the LED chip though the I2C-bus of the PCAN-PCIeC
+ */
+static int peak_pciec_write_pca9553(struct peak_pciec_card *card,
+ u8 offset, u8 data)
+{
+ u8 buffer[2] = {
+ offset,
+ data
+ };
+ struct i2c_msg msg = {
+ .addr = PCA9553_1_SLAVEADDR,
+ .len = 2,
+ .buf = buffer,
+ };
+ int ret;
+
+ /* cache led mask */
+ if ((offset == 5) && (data == card->led_cache))
+ return 0;
+
+ ret = i2c_transfer(&card->led_chip, &msg, 1);
+ if (ret < 0)
+ return ret;
+
+ if (offset == 5)
+ card->led_cache = data;
+
+ return 0;
+}
+
+/*
+ * delayed work callback used to control the LEDs
+ */
+static void peak_pciec_led_work(struct work_struct *work)
+{
+ struct peak_pciec_card *card =
+ container_of(work, struct peak_pciec_card, led_work.work);
+ struct net_device *netdev;
+ u8 new_led = card->led_cache;
+ int i, up_count = 0;
+
+ /* first check what is to do */
+ for (i = 0; i < card->chan_count; i++) {
+ /* default is: not configured */
+ new_led &= ~PCA9553_LED_MASK(i);
+ new_led |= PCA9553_LED_ON(i);
+
+ netdev = card->channel[i].netdev;
+ if (!netdev || !(netdev->flags & IFF_UP))
+ continue;
+
+ up_count++;
+
+ /* no activity (but configured) */
+ new_led &= ~PCA9553_LED_MASK(i);
+ new_led |= PCA9553_LED_SLOW(i);
+
+ /* if bytes counters changed, set fast blinking led */
+ if (netdev->stats.rx_bytes != card->channel[i].prev_rx_bytes) {
+ card->channel[i].prev_rx_bytes = netdev->stats.rx_bytes;
+ new_led &= ~PCA9553_LED_MASK(i);
+ new_led |= PCA9553_LED_FAST(i);
+ }
+ if (netdev->stats.tx_bytes != card->channel[i].prev_tx_bytes) {
+ card->channel[i].prev_tx_bytes = netdev->stats.tx_bytes;
+ new_led &= ~PCA9553_LED_MASK(i);
+ new_led |= PCA9553_LED_FAST(i);
+ }
+ }
+
+ /* check if LS0 settings changed, only update i2c if so */
+ peak_pciec_write_pca9553(card, 5, new_led);
+
+ /* restart timer (except if no more configured channels) */
+ if (up_count)
+ schedule_delayed_work(&card->led_work, HZ);
+}
+
+/*
+ * set LEDs blinking state
+ */
+static void peak_pciec_set_leds(struct peak_pciec_card *card, u8 led_mask, u8 s)
+{
+ u8 new_led = card->led_cache;
+ int i;
+
+ /* first check what is to do */
+ for (i = 0; i < card->chan_count; i++)
+ if (led_mask & PCA9553_LED(i)) {
+ new_led &= ~PCA9553_LED_MASK(i);
+ new_led |= PCA9553_LED_STATE(s, i);
+ }
+
+ /* check if LS0 settings changed, only update i2c if so */
+ peak_pciec_write_pca9553(card, 5, new_led);
+}
+
+/*
+ * start one second delayed work to control LEDs
+ */
+static void peak_pciec_start_led_work(struct peak_pciec_card *card)
+{
+ schedule_delayed_work(&card->led_work, HZ);
+}
+
+/*
+ * stop LEDs delayed work
+ */
+static void peak_pciec_stop_led_work(struct peak_pciec_card *card)
+{
+ cancel_delayed_work_sync(&card->led_work);
+}
+
+/*
+ * initialize the PCA9553 4-bit I2C-bus LED chip
+ */
+static int peak_pciec_init_leds(struct peak_pciec_card *card)
+{
+ int err;
+
+ /* prescaler for frequency 0: "SLOW" = 1 Hz = "44" */
+ err = peak_pciec_write_pca9553(card, 1, 44 / 1);
+ if (err)
+ return err;
+
+ /* duty cycle 0: 50% */
+ err = peak_pciec_write_pca9553(card, 2, 0x80);
+ if (err)
+ return err;
+
+ /* prescaler for frequency 1: "FAST" = 5 Hz */
+ err = peak_pciec_write_pca9553(card, 3, 44 / 5);
+ if (err)
+ return err;
+
+ /* duty cycle 1: 50% */
+ err = peak_pciec_write_pca9553(card, 4, 0x80);
+ if (err)
+ return err;
+
+ /* switch LEDs to initial state */
+ return peak_pciec_write_pca9553(card, 5, PCA9553_LS0_INIT);
+}
+
+/*
+ * restore LEDs state to off peak_pciec_leds_exit
+ */
+static void peak_pciec_leds_exit(struct peak_pciec_card *card)
+{
+ /* switch LEDs to off */
+ peak_pciec_write_pca9553(card, 5, PCA9553_LED_OFF_ALL);
+}
+
+/*
+ * normal write sja1000 register method overloaded to catch when controller
+ * is started or stopped, to control leds
+ */
+static void peak_pciec_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val)
+{
+ struct peak_pci_chan *chan = priv->priv;
+ struct peak_pciec_card *card = chan->pciec_card;
+ int c = (priv->reg_base - card->reg_base) / PEAK_PCI_CHAN_SIZE;
+
+ /* sja1000 register changes control the leds state */
+ if (port == SJA1000_MOD)
+ switch (val) {
+ case MOD_RM:
+ /* Reset Mode: set led on */
+ peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_ON);
+ break;
+ case 0x00:
+ /* Normal Mode: led slow blinking and start led timer */
+ peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_SLOW);
+ peak_pciec_start_led_work(card);
+ break;
+ default:
+ break;
+ }
+
+ /* call base function */
+ peak_pci_write_reg(priv, port, val);
+}
+
+static struct i2c_algo_bit_data peak_pciec_i2c_bit_ops = {
+ .setsda = pita_setsda,
+ .setscl = pita_setscl,
+ .getsda = pita_getsda,
+ .getscl = pita_getscl,
+ .udelay = 10,
+ .timeout = HZ,
+};
+
+static int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct peak_pci_chan *chan = priv->priv;
+ struct peak_pciec_card *card;
+ int err;
+
+ /* copy i2c object address from 1st channel */
+ if (chan->prev_dev) {
+ struct sja1000_priv *prev_priv = netdev_priv(chan->prev_dev);
+ struct peak_pci_chan *prev_chan = prev_priv->priv;
+
+ card = prev_chan->pciec_card;
+ if (!card)
+ return -ENODEV;
+
+ /* channel is the first one: do the init part */
+ } else {
+ /* create the bit banging I2C adapter structure */
+ card = kzalloc(sizeof(struct peak_pciec_card), GFP_KERNEL);
+ if (!card)
+ return -ENOMEM;
+
+ card->cfg_base = chan->cfg_base;
+ card->reg_base = priv->reg_base;
+
+ card->led_chip.owner = THIS_MODULE;
+ card->led_chip.dev.parent = &pdev->dev;
+ card->led_chip.algo_data = &card->i2c_bit;
+ strncpy(card->led_chip.name, "peak_i2c",
+ sizeof(card->led_chip.name));
+
+ card->i2c_bit = peak_pciec_i2c_bit_ops;
+ card->i2c_bit.udelay = 10;
+ card->i2c_bit.timeout = HZ;
+ card->i2c_bit.data = card;
+
+ peak_pciec_init_pita_gpio(card);
+
+ err = i2c_bit_add_bus(&card->led_chip);
+ if (err) {
+ dev_err(&pdev->dev, "i2c init failed\n");
+ goto pciec_init_err_1;
+ }
+
+ err = peak_pciec_init_leds(card);
+ if (err) {
+ dev_err(&pdev->dev, "leds hardware init failed\n");
+ goto pciec_init_err_2;
+ }
+
+ INIT_DELAYED_WORK(&card->led_work, peak_pciec_led_work);
+ /* PCAN-ExpressCard needs its own callback for leds */
+ priv->write_reg = peak_pciec_write_reg;
+ }
+
+ chan->pciec_card = card;
+ card->channel[card->chan_count++].netdev = dev;
+
+ return 0;
+
+pciec_init_err_2:
+ i2c_del_adapter(&card->led_chip);
+
+pciec_init_err_1:
+ peak_pciec_init_pita_gpio(card);
+ kfree(card);
+
+ return err;
+}
+
+static void peak_pciec_remove(struct peak_pciec_card *card)
+{
+ peak_pciec_stop_led_work(card);
+ peak_pciec_leds_exit(card);
+ i2c_del_adapter(&card->led_chip);
+ peak_pciec_init_pita_gpio(card);
+ kfree(card);
+}
+
+#else /* CONFIG_CAN_PEAK_PCIEC */
+
+/*
+ * Placebo functions when PCAN-ExpressCard support is not selected
+ */
+static inline int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
+{
+ return -ENODEV;
+}
+
+static inline void peak_pciec_remove(struct peak_pciec_card *card)
+{
+}
+#endif /* CONFIG_CAN_PEAK_PCIEC */
+
+static u8 peak_pci_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return readb(priv->reg_base + (port << 2));
+}
+
+static void peak_pci_write_reg(const struct sja1000_priv *priv,
+ int port, u8 val)
+{
+ writeb(val, priv->reg_base + (port << 2));
+}
+
+static void peak_pci_post_irq(const struct sja1000_priv *priv)
+{
+ struct peak_pci_chan *chan = priv->priv;
+ u16 icr;
+
+ /* Select and clear in PITA stored interrupt */
+ icr = readw(chan->cfg_base + PITA_ICR);
+ if (icr & chan->icr_mask)
+ writew(chan->icr_mask, chan->cfg_base + PITA_ICR);
+}
+
+static int peak_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct sja1000_priv *priv;
+ struct peak_pci_chan *chan;
+ struct net_device *dev, *prev_dev;
+ void __iomem *cfg_base, *reg_base;
+ u16 sub_sys_id, icr;
+ int i, err, channels;
+
+ err = pci_enable_device(pdev);
+ if (err)
+ return err;
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err)
+ goto failure_disable_pci;
+
+ err = pci_read_config_word(pdev, 0x2e, &sub_sys_id);
+ if (err)
+ goto failure_release_regions;
+
+ dev_dbg(&pdev->dev, "probing device %04x:%04x:%04x\n",
+ pdev->vendor, pdev->device, sub_sys_id);
+
+ err = pci_write_config_word(pdev, 0x44, 0);
+ if (err)
+ goto failure_release_regions;
+
+ if (sub_sys_id >= 12)
+ channels = 4;
+ else if (sub_sys_id >= 10)
+ channels = 3;
+ else if (sub_sys_id >= 4)
+ channels = 2;
+ else
+ channels = 1;
+
+ cfg_base = pci_iomap(pdev, 0, PEAK_PCI_CFG_SIZE);
+ if (!cfg_base) {
+ dev_err(&pdev->dev, "failed to map PCI resource #0\n");
+ err = -ENOMEM;
+ goto failure_release_regions;
+ }
+
+ reg_base = pci_iomap(pdev, 1, PEAK_PCI_CHAN_SIZE * channels);
+ if (!reg_base) {
+ dev_err(&pdev->dev, "failed to map PCI resource #1\n");
+ err = -ENOMEM;
+ goto failure_unmap_cfg_base;
+ }
+
+ /* Set GPIO control register */
+ writew(0x0005, cfg_base + PITA_GPIOICR + 2);
+ /* Enable all channels of this card */
+ writeb(0x00, cfg_base + PITA_GPIOICR);
+ /* Toggle reset */
+ writeb(0x05, cfg_base + PITA_MISC + 3);
+ mdelay(5);
+ /* Leave parport mux mode */
+ writeb(0x04, cfg_base + PITA_MISC + 3);
+
+ icr = readw(cfg_base + PITA_ICR + 2);
+
+ for (i = 0; i < channels; i++) {
+ dev = alloc_sja1000dev(sizeof(struct peak_pci_chan));
+ if (!dev) {
+ err = -ENOMEM;
+ goto failure_remove_channels;
+ }
+
+ priv = netdev_priv(dev);
+ chan = priv->priv;
+
+ chan->cfg_base = cfg_base;
+ priv->reg_base = reg_base + i * PEAK_PCI_CHAN_SIZE;
+
+ priv->read_reg = peak_pci_read_reg;
+ priv->write_reg = peak_pci_write_reg;
+ priv->post_irq = peak_pci_post_irq;
+
+ priv->can.clock.freq = PEAK_PCI_CAN_CLOCK;
+ priv->ocr = PEAK_PCI_OCR;
+ priv->cdr = PEAK_PCI_CDR;
+ /* Neither a slave nor a single device distributes the clock */
+ if (channels == 1 || i > 0)
+ priv->cdr |= CDR_CLK_OFF;
+
+ /* Setup interrupt handling */
+ priv->irq_flags = IRQF_SHARED;
+ dev->irq = pdev->irq;
+
+ chan->icr_mask = peak_pci_icr_masks[i];
+ icr |= chan->icr_mask;
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = i;
+
+ /* Create chain of SJA1000 devices */
+ chan->prev_dev = pci_get_drvdata(pdev);
+ pci_set_drvdata(pdev, dev);
+
+ /*
+ * PCAN-ExpressCard needs some additional i2c init.
+ * This must be done *before* register_sja1000dev() but
+ * *after* devices linkage
+ */
+ if (pdev->device == PEAK_PCIEC_DEVICE_ID ||
+ pdev->device == PEAK_PCIEC34_DEVICE_ID) {
+ err = peak_pciec_probe(pdev, dev);
+ if (err) {
+ dev_err(&pdev->dev,
+ "failed to probe device (err %d)\n",
+ err);
+ goto failure_free_dev;
+ }
+ }
+
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "failed to register device\n");
+ goto failure_free_dev;
+ }
+
+ dev_info(&pdev->dev,
+ "%s at reg_base=0x%p cfg_base=0x%p irq=%d\n",
+ dev->name, priv->reg_base, chan->cfg_base, dev->irq);
+ }
+
+ /* Enable interrupts */
+ writew(icr, cfg_base + PITA_ICR + 2);
+
+ return 0;
+
+failure_free_dev:
+ pci_set_drvdata(pdev, chan->prev_dev);
+ free_sja1000dev(dev);
+
+failure_remove_channels:
+ /* Disable interrupts */
+ writew(0x0, cfg_base + PITA_ICR + 2);
+
+ chan = NULL;
+ for (dev = pci_get_drvdata(pdev); dev; dev = prev_dev) {
+ priv = netdev_priv(dev);
+ chan = priv->priv;
+ prev_dev = chan->prev_dev;
+
+ unregister_sja1000dev(dev);
+ free_sja1000dev(dev);
+ }
+
+ /* free any PCIeC resources too */
+ if (chan && chan->pciec_card)
+ peak_pciec_remove(chan->pciec_card);
+
+ pci_iounmap(pdev, reg_base);
+
+failure_unmap_cfg_base:
+ pci_iounmap(pdev, cfg_base);
+
+failure_release_regions:
+ pci_release_regions(pdev);
+
+failure_disable_pci:
+ pci_disable_device(pdev);
+
+ return err;
+}
+
+static void peak_pci_remove(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev); /* Last device */
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct peak_pci_chan *chan = priv->priv;
+ void __iomem *cfg_base = chan->cfg_base;
+ void __iomem *reg_base = priv->reg_base;
+
+ /* Disable interrupts */
+ writew(0x0, cfg_base + PITA_ICR + 2);
+
+ /* Loop over all registered devices */
+ while (1) {
+ struct net_device *prev_dev = chan->prev_dev;
+
+ dev_info(&pdev->dev, "removing device %s\n", dev->name);
+ unregister_sja1000dev(dev);
+ free_sja1000dev(dev);
+ dev = prev_dev;
+
+ if (!dev) {
+ /* do that only for first channel */
+ if (chan->pciec_card)
+ peak_pciec_remove(chan->pciec_card);
+ break;
+ }
+ priv = netdev_priv(dev);
+ chan = priv->priv;
+ }
+
+ pci_iounmap(pdev, reg_base);
+ pci_iounmap(pdev, cfg_base);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+}
+
+static struct pci_driver peak_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = peak_pci_tbl,
+ .probe = peak_pci_probe,
+ .remove = peak_pci_remove,
+};
+
+module_pci_driver(peak_pci_driver);
diff --git a/drivers/net/can/sja1000/peak_pcmcia.c b/drivers/net/can/sja1000/peak_pcmcia.c
new file mode 100644
index 000000000..dd56133cc
--- /dev/null
+++ b/drivers/net/can/sja1000/peak_pcmcia.c
@@ -0,0 +1,744 @@
+/*
+ * Copyright (C) 2010-2012 Stephane Grosjean <s.grosjean@peak-system.com>
+ *
+ * CAN driver for PEAK-System PCAN-PC Card
+ * Derived from the PCAN project file driver/src/pcan_pccard.c
+ * Copyright (C) 2006-2010 PEAK System-Technik GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/io.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include "sja1000.h"
+
+MODULE_AUTHOR("Stephane Grosjean <s.grosjean@peak-system.com>");
+MODULE_DESCRIPTION("CAN driver for PEAK-System PCAN-PC Cards");
+MODULE_LICENSE("GPL v2");
+MODULE_SUPPORTED_DEVICE("PEAK PCAN-PC Card");
+
+/* PEAK-System PCMCIA driver name */
+#define PCC_NAME "peak_pcmcia"
+
+#define PCC_CHAN_MAX 2
+
+#define PCC_CAN_CLOCK (16000000 / 2)
+
+#define PCC_MANF_ID 0x0377
+#define PCC_CARD_ID 0x0001
+
+#define PCC_CHAN_SIZE 0x20
+#define PCC_CHAN_OFF(c) ((c) * PCC_CHAN_SIZE)
+#define PCC_COMN_OFF (PCC_CHAN_OFF(PCC_CHAN_MAX))
+#define PCC_COMN_SIZE 0x40
+
+/* common area registers */
+#define PCC_CCR 0x00
+#define PCC_CSR 0x02
+#define PCC_CPR 0x04
+#define PCC_SPI_DIR 0x06
+#define PCC_SPI_DOR 0x08
+#define PCC_SPI_ADR 0x0a
+#define PCC_SPI_IR 0x0c
+#define PCC_FW_MAJOR 0x10
+#define PCC_FW_MINOR 0x12
+
+/* CCR bits */
+#define PCC_CCR_CLK_16 0x00
+#define PCC_CCR_CLK_10 0x01
+#define PCC_CCR_CLK_21 0x02
+#define PCC_CCR_CLK_8 0x03
+#define PCC_CCR_CLK_MASK PCC_CCR_CLK_8
+
+#define PCC_CCR_RST_CHAN(c) (0x01 << ((c) + 2))
+#define PCC_CCR_RST_ALL (PCC_CCR_RST_CHAN(0) | PCC_CCR_RST_CHAN(1))
+#define PCC_CCR_RST_MASK PCC_CCR_RST_ALL
+
+/* led selection bits */
+#define PCC_LED(c) (1 << (c))
+#define PCC_LED_ALL (PCC_LED(0) | PCC_LED(1))
+
+/* led state value */
+#define PCC_LED_ON 0x00
+#define PCC_LED_FAST 0x01
+#define PCC_LED_SLOW 0x02
+#define PCC_LED_OFF 0x03
+
+#define PCC_CCR_LED_CHAN(s, c) ((s) << (((c) + 2) << 1))
+
+#define PCC_CCR_LED_ON_CHAN(c) PCC_CCR_LED_CHAN(PCC_LED_ON, c)
+#define PCC_CCR_LED_FAST_CHAN(c) PCC_CCR_LED_CHAN(PCC_LED_FAST, c)
+#define PCC_CCR_LED_SLOW_CHAN(c) PCC_CCR_LED_CHAN(PCC_LED_SLOW, c)
+#define PCC_CCR_LED_OFF_CHAN(c) PCC_CCR_LED_CHAN(PCC_LED_OFF, c)
+#define PCC_CCR_LED_MASK_CHAN(c) PCC_CCR_LED_OFF_CHAN(c)
+#define PCC_CCR_LED_OFF_ALL (PCC_CCR_LED_OFF_CHAN(0) | \
+ PCC_CCR_LED_OFF_CHAN(1))
+#define PCC_CCR_LED_MASK PCC_CCR_LED_OFF_ALL
+
+#define PCC_CCR_INIT (PCC_CCR_CLK_16 | PCC_CCR_RST_ALL | PCC_CCR_LED_OFF_ALL)
+
+/* CSR bits */
+#define PCC_CSR_SPI_BUSY 0x04
+
+/* time waiting for SPI busy (prevent from infinite loop) */
+#define PCC_SPI_MAX_BUSY_WAIT_MS 3
+
+/* max count of reading the SPI status register waiting for a change */
+/* (prevent from infinite loop) */
+#define PCC_WRITE_MAX_LOOP 1000
+
+/* max nb of int handled by that isr in one shot (prevent from infinite loop) */
+#define PCC_ISR_MAX_LOOP 10
+
+/* EEPROM chip instruction set */
+/* note: EEPROM Read/Write instructions include A8 bit */
+#define PCC_EEP_WRITE(a) (0x02 | (((a) & 0x100) >> 5))
+#define PCC_EEP_READ(a) (0x03 | (((a) & 0x100) >> 5))
+#define PCC_EEP_WRDI 0x04 /* EEPROM Write Disable */
+#define PCC_EEP_RDSR 0x05 /* EEPROM Read Status Register */
+#define PCC_EEP_WREN 0x06 /* EEPROM Write Enable */
+
+/* EEPROM Status Register bits */
+#define PCC_EEP_SR_WEN 0x02 /* EEPROM SR Write Enable bit */
+#define PCC_EEP_SR_WIP 0x01 /* EEPROM SR Write In Progress bit */
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode, push-pull and the correct polarity.
+ */
+#define PCC_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 7
+ * (meaning direct oscillator output) because the second SJA1000 chip
+ * is driven by the first one CLKOUT output.
+ */
+#define PCC_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+
+struct pcan_channel {
+ struct net_device *netdev;
+ unsigned long prev_rx_bytes;
+ unsigned long prev_tx_bytes;
+};
+
+/* PCAN-PC Card private structure */
+struct pcan_pccard {
+ struct pcmcia_device *pdev;
+ int chan_count;
+ struct pcan_channel channel[PCC_CHAN_MAX];
+ u8 ccr;
+ u8 fw_major;
+ u8 fw_minor;
+ void __iomem *ioport_addr;
+ struct timer_list led_timer;
+};
+
+static struct pcmcia_device_id pcan_table[] = {
+ PCMCIA_DEVICE_MANF_CARD(PCC_MANF_ID, PCC_CARD_ID),
+ PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, pcan_table);
+
+static void pcan_set_leds(struct pcan_pccard *card, u8 mask, u8 state);
+
+/*
+ * start timer which controls leds state
+ */
+static void pcan_start_led_timer(struct pcan_pccard *card)
+{
+ if (!timer_pending(&card->led_timer))
+ mod_timer(&card->led_timer, jiffies + HZ);
+}
+
+/*
+ * stop the timer which controls leds state
+ */
+static void pcan_stop_led_timer(struct pcan_pccard *card)
+{
+ del_timer_sync(&card->led_timer);
+}
+
+/*
+ * read a sja1000 register
+ */
+static u8 pcan_read_canreg(const struct sja1000_priv *priv, int port)
+{
+ return ioread8(priv->reg_base + port);
+}
+
+/*
+ * write a sja1000 register
+ */
+static void pcan_write_canreg(const struct sja1000_priv *priv, int port, u8 v)
+{
+ struct pcan_pccard *card = priv->priv;
+ int c = (priv->reg_base - card->ioport_addr) / PCC_CHAN_SIZE;
+
+ /* sja1000 register changes control the leds state */
+ if (port == SJA1000_MOD)
+ switch (v) {
+ case MOD_RM:
+ /* Reset Mode: set led on */
+ pcan_set_leds(card, PCC_LED(c), PCC_LED_ON);
+ break;
+ case 0x00:
+ /* Normal Mode: led slow blinking and start led timer */
+ pcan_set_leds(card, PCC_LED(c), PCC_LED_SLOW);
+ pcan_start_led_timer(card);
+ break;
+ default:
+ break;
+ }
+
+ iowrite8(v, priv->reg_base + port);
+}
+
+/*
+ * read a register from the common area
+ */
+static u8 pcan_read_reg(struct pcan_pccard *card, int port)
+{
+ return ioread8(card->ioport_addr + PCC_COMN_OFF + port);
+}
+
+/*
+ * write a register into the common area
+ */
+static void pcan_write_reg(struct pcan_pccard *card, int port, u8 v)
+{
+ /* cache ccr value */
+ if (port == PCC_CCR) {
+ if (card->ccr == v)
+ return;
+ card->ccr = v;
+ }
+
+ iowrite8(v, card->ioport_addr + PCC_COMN_OFF + port);
+}
+
+/*
+ * check whether the card is present by checking its fw version numbers
+ * against values read at probing time.
+ */
+static inline int pcan_pccard_present(struct pcan_pccard *card)
+{
+ return ((pcan_read_reg(card, PCC_FW_MAJOR) == card->fw_major) &&
+ (pcan_read_reg(card, PCC_FW_MINOR) == card->fw_minor));
+}
+
+/*
+ * wait for SPI engine while it is busy
+ */
+static int pcan_wait_spi_busy(struct pcan_pccard *card)
+{
+ unsigned long timeout = jiffies +
+ msecs_to_jiffies(PCC_SPI_MAX_BUSY_WAIT_MS) + 1;
+
+ /* be sure to read status at least once after sleeping */
+ while (pcan_read_reg(card, PCC_CSR) & PCC_CSR_SPI_BUSY) {
+ if (time_after(jiffies, timeout))
+ return -EBUSY;
+ schedule();
+ }
+
+ return 0;
+}
+
+/*
+ * write data in device eeprom
+ */
+static int pcan_write_eeprom(struct pcan_pccard *card, u16 addr, u8 v)
+{
+ u8 status;
+ int err, i;
+
+ /* write instruction enabling write */
+ pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WREN);
+ err = pcan_wait_spi_busy(card);
+ if (err)
+ goto we_spi_err;
+
+ /* wait until write enabled */
+ for (i = 0; i < PCC_WRITE_MAX_LOOP; i++) {
+ /* write instruction reading the status register */
+ pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_RDSR);
+ err = pcan_wait_spi_busy(card);
+ if (err)
+ goto we_spi_err;
+
+ /* get status register value and check write enable bit */
+ status = pcan_read_reg(card, PCC_SPI_DIR);
+ if (status & PCC_EEP_SR_WEN)
+ break;
+ }
+
+ if (i >= PCC_WRITE_MAX_LOOP) {
+ dev_err(&card->pdev->dev,
+ "stop waiting to be allowed to write in eeprom\n");
+ return -EIO;
+ }
+
+ /* set address and data */
+ pcan_write_reg(card, PCC_SPI_ADR, addr & 0xff);
+ pcan_write_reg(card, PCC_SPI_DOR, v);
+
+ /*
+ * write instruction with bit[3] set according to address value:
+ * if addr refers to upper half of the memory array: bit[3] = 1
+ */
+ pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WRITE(addr));
+ err = pcan_wait_spi_busy(card);
+ if (err)
+ goto we_spi_err;
+
+ /* wait while write in progress */
+ for (i = 0; i < PCC_WRITE_MAX_LOOP; i++) {
+ /* write instruction reading the status register */
+ pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_RDSR);
+ err = pcan_wait_spi_busy(card);
+ if (err)
+ goto we_spi_err;
+
+ /* get status register value and check write in progress bit */
+ status = pcan_read_reg(card, PCC_SPI_DIR);
+ if (!(status & PCC_EEP_SR_WIP))
+ break;
+ }
+
+ if (i >= PCC_WRITE_MAX_LOOP) {
+ dev_err(&card->pdev->dev,
+ "stop waiting for write in eeprom to complete\n");
+ return -EIO;
+ }
+
+ /* write instruction disabling write */
+ pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WRDI);
+ err = pcan_wait_spi_busy(card);
+ if (err)
+ goto we_spi_err;
+
+ return 0;
+
+we_spi_err:
+ dev_err(&card->pdev->dev,
+ "stop waiting (spi engine always busy) err %d\n", err);
+
+ return err;
+}
+
+static void pcan_set_leds(struct pcan_pccard *card, u8 led_mask, u8 state)
+{
+ u8 ccr = card->ccr;
+ int i;
+
+ for (i = 0; i < card->chan_count; i++)
+ if (led_mask & PCC_LED(i)) {
+ /* clear corresponding led bits in ccr */
+ ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+ /* then set new bits */
+ ccr |= PCC_CCR_LED_CHAN(state, i);
+ }
+
+ /* real write only if something has changed in ccr */
+ pcan_write_reg(card, PCC_CCR, ccr);
+}
+
+/*
+ * enable/disable CAN connectors power
+ */
+static inline void pcan_set_can_power(struct pcan_pccard *card, int onoff)
+{
+ int err;
+
+ err = pcan_write_eeprom(card, 0, !!onoff);
+ if (err)
+ dev_err(&card->pdev->dev,
+ "failed setting power %s to can connectors (err %d)\n",
+ (onoff) ? "on" : "off", err);
+}
+
+/*
+ * set leds state according to channel activity
+ */
+static void pcan_led_timer(unsigned long arg)
+{
+ struct pcan_pccard *card = (struct pcan_pccard *)arg;
+ struct net_device *netdev;
+ int i, up_count = 0;
+ u8 ccr;
+
+ ccr = card->ccr;
+ for (i = 0; i < card->chan_count; i++) {
+ /* default is: not configured */
+ ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+ ccr |= PCC_CCR_LED_ON_CHAN(i);
+
+ netdev = card->channel[i].netdev;
+ if (!netdev || !(netdev->flags & IFF_UP))
+ continue;
+
+ up_count++;
+
+ /* no activity (but configured) */
+ ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+ ccr |= PCC_CCR_LED_SLOW_CHAN(i);
+
+ /* if bytes counters changed, set fast blinking led */
+ if (netdev->stats.rx_bytes != card->channel[i].prev_rx_bytes) {
+ card->channel[i].prev_rx_bytes = netdev->stats.rx_bytes;
+ ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+ ccr |= PCC_CCR_LED_FAST_CHAN(i);
+ }
+ if (netdev->stats.tx_bytes != card->channel[i].prev_tx_bytes) {
+ card->channel[i].prev_tx_bytes = netdev->stats.tx_bytes;
+ ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+ ccr |= PCC_CCR_LED_FAST_CHAN(i);
+ }
+ }
+
+ /* write the new leds state */
+ pcan_write_reg(card, PCC_CCR, ccr);
+
+ /* restart timer (except if no more configured channels) */
+ if (up_count)
+ mod_timer(&card->led_timer, jiffies + HZ);
+}
+
+/*
+ * interrupt service routine
+ */
+static irqreturn_t pcan_isr(int irq, void *dev_id)
+{
+ struct pcan_pccard *card = dev_id;
+ int irq_handled;
+
+ /* prevent from infinite loop */
+ for (irq_handled = 0; irq_handled < PCC_ISR_MAX_LOOP; irq_handled++) {
+ /* handle shared interrupt and next loop */
+ int nothing_to_handle = 1;
+ int i;
+
+ /* check interrupt for each channel */
+ for (i = 0; i < card->chan_count; i++) {
+ struct net_device *netdev;
+
+ /*
+ * check whether the card is present before calling
+ * sja1000_interrupt() to speed up hotplug detection
+ */
+ if (!pcan_pccard_present(card)) {
+ /* card unplugged during isr */
+ return IRQ_NONE;
+ }
+
+ /*
+ * should check whether all or SJA1000_MAX_IRQ
+ * interrupts have been handled: loop again to be sure.
+ */
+ netdev = card->channel[i].netdev;
+ if (netdev &&
+ sja1000_interrupt(irq, netdev) == IRQ_HANDLED)
+ nothing_to_handle = 0;
+ }
+
+ if (nothing_to_handle)
+ break;
+ }
+
+ return (irq_handled) ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/*
+ * free all resources used by the channels and switch off leds and can power
+ */
+static void pcan_free_channels(struct pcan_pccard *card)
+{
+ int i;
+ u8 led_mask = 0;
+
+ for (i = 0; i < card->chan_count; i++) {
+ struct net_device *netdev;
+ char name[IFNAMSIZ];
+
+ led_mask |= PCC_LED(i);
+
+ netdev = card->channel[i].netdev;
+ if (!netdev)
+ continue;
+
+ strncpy(name, netdev->name, IFNAMSIZ);
+
+ unregister_sja1000dev(netdev);
+
+ free_sja1000dev(netdev);
+
+ dev_info(&card->pdev->dev, "%s removed\n", name);
+ }
+
+ /* do it only if device not removed */
+ if (pcan_pccard_present(card)) {
+ pcan_set_leds(card, led_mask, PCC_LED_OFF);
+ pcan_set_can_power(card, 0);
+ }
+}
+
+/*
+ * check if a CAN controller is present at the specified location
+ */
+static inline int pcan_channel_present(struct sja1000_priv *priv)
+{
+ /* make sure SJA1000 is in reset mode */
+ pcan_write_canreg(priv, SJA1000_MOD, 1);
+ pcan_write_canreg(priv, SJA1000_CDR, CDR_PELICAN);
+
+ /* read reset-values */
+ if (pcan_read_canreg(priv, SJA1000_CDR) == CDR_PELICAN)
+ return 1;
+
+ return 0;
+}
+
+static int pcan_add_channels(struct pcan_pccard *card)
+{
+ struct pcmcia_device *pdev = card->pdev;
+ int i, err = 0;
+ u8 ccr = PCC_CCR_INIT;
+
+ /* init common registers (reset channels and leds off) */
+ card->ccr = ~ccr;
+ pcan_write_reg(card, PCC_CCR, ccr);
+
+ /* wait 2ms before unresetting channels */
+ mdelay(2);
+
+ ccr &= ~PCC_CCR_RST_ALL;
+ pcan_write_reg(card, PCC_CCR, ccr);
+
+ /* create one network device per channel detected */
+ for (i = 0; i < ARRAY_SIZE(card->channel); i++) {
+ struct net_device *netdev;
+ struct sja1000_priv *priv;
+
+ netdev = alloc_sja1000dev(0);
+ if (!netdev) {
+ err = -ENOMEM;
+ break;
+ }
+
+ /* update linkages */
+ priv = netdev_priv(netdev);
+ priv->priv = card;
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+ netdev->dev_id = i;
+
+ priv->irq_flags = IRQF_SHARED;
+ netdev->irq = pdev->irq;
+ priv->reg_base = card->ioport_addr + PCC_CHAN_OFF(i);
+
+ /* check if channel is present */
+ if (!pcan_channel_present(priv)) {
+ dev_err(&pdev->dev, "channel %d not present\n", i);
+ free_sja1000dev(netdev);
+ continue;
+ }
+
+ priv->read_reg = pcan_read_canreg;
+ priv->write_reg = pcan_write_canreg;
+ priv->can.clock.freq = PCC_CAN_CLOCK;
+ priv->ocr = PCC_OCR;
+ priv->cdr = PCC_CDR;
+
+ /* Neither a slave device distributes the clock */
+ if (i > 0)
+ priv->cdr |= CDR_CLK_OFF;
+
+ priv->flags |= SJA1000_CUSTOM_IRQ_HANDLER;
+
+ /* register SJA1000 device */
+ err = register_sja1000dev(netdev);
+ if (err) {
+ free_sja1000dev(netdev);
+ continue;
+ }
+
+ card->channel[i].netdev = netdev;
+ card->chan_count++;
+
+ /* set corresponding led on in the new ccr */
+ ccr &= ~PCC_CCR_LED_OFF_CHAN(i);
+
+ dev_info(&pdev->dev,
+ "%s on channel %d at 0x%p irq %d\n",
+ netdev->name, i, priv->reg_base, pdev->irq);
+ }
+
+ /* write new ccr (change leds state) */
+ pcan_write_reg(card, PCC_CCR, ccr);
+
+ return err;
+}
+
+static int pcan_conf_check(struct pcmcia_device *pdev, void *priv_data)
+{
+ pdev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+ pdev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8; /* only */
+ pdev->io_lines = 10;
+
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(pdev);
+}
+
+/*
+ * free all resources used by the device
+ */
+static void pcan_free(struct pcmcia_device *pdev)
+{
+ struct pcan_pccard *card = pdev->priv;
+
+ if (!card)
+ return;
+
+ free_irq(pdev->irq, card);
+ pcan_stop_led_timer(card);
+
+ pcan_free_channels(card);
+
+ ioport_unmap(card->ioport_addr);
+
+ kfree(card);
+ pdev->priv = NULL;
+}
+
+/*
+ * setup PCMCIA socket and probe for PEAK-System PC-CARD
+ */
+static int pcan_probe(struct pcmcia_device *pdev)
+{
+ struct pcan_pccard *card;
+ int err;
+
+ pdev->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
+
+ err = pcmcia_loop_config(pdev, pcan_conf_check, NULL);
+ if (err) {
+ dev_err(&pdev->dev, "pcmcia_loop_config() error %d\n", err);
+ goto probe_err_1;
+ }
+
+ if (!pdev->irq) {
+ dev_err(&pdev->dev, "no irq assigned\n");
+ err = -ENODEV;
+ goto probe_err_1;
+ }
+
+ err = pcmcia_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "pcmcia_enable_device failed err=%d\n",
+ err);
+ goto probe_err_1;
+ }
+
+ card = kzalloc(sizeof(struct pcan_pccard), GFP_KERNEL);
+ if (!card) {
+ err = -ENOMEM;
+ goto probe_err_2;
+ }
+
+ card->pdev = pdev;
+ pdev->priv = card;
+
+ /* sja1000 api uses iomem */
+ card->ioport_addr = ioport_map(pdev->resource[0]->start,
+ resource_size(pdev->resource[0]));
+ if (!card->ioport_addr) {
+ dev_err(&pdev->dev, "couldn't map io port into io memory\n");
+ err = -ENOMEM;
+ goto probe_err_3;
+ }
+ card->fw_major = pcan_read_reg(card, PCC_FW_MAJOR);
+ card->fw_minor = pcan_read_reg(card, PCC_FW_MINOR);
+
+ /* display board name and firware version */
+ dev_info(&pdev->dev, "PEAK-System pcmcia card %s fw %d.%d\n",
+ pdev->prod_id[1] ? pdev->prod_id[1] : "PCAN-PC Card",
+ card->fw_major, card->fw_minor);
+
+ /* detect available channels */
+ pcan_add_channels(card);
+ if (!card->chan_count) {
+ err = -ENOMEM;
+ goto probe_err_4;
+ }
+
+ /* init the timer which controls the leds */
+ init_timer(&card->led_timer);
+ card->led_timer.function = pcan_led_timer;
+ card->led_timer.data = (unsigned long)card;
+
+ /* request the given irq */
+ err = request_irq(pdev->irq, &pcan_isr, IRQF_SHARED, PCC_NAME, card);
+ if (err) {
+ dev_err(&pdev->dev, "couldn't request irq%d\n", pdev->irq);
+ goto probe_err_5;
+ }
+
+ /* power on the connectors */
+ pcan_set_can_power(card, 1);
+
+ return 0;
+
+probe_err_5:
+ /* unregister can devices from network */
+ pcan_free_channels(card);
+
+probe_err_4:
+ ioport_unmap(card->ioport_addr);
+
+probe_err_3:
+ kfree(card);
+ pdev->priv = NULL;
+
+probe_err_2:
+ pcmcia_disable_device(pdev);
+
+probe_err_1:
+ return err;
+}
+
+/*
+ * release claimed resources
+ */
+static void pcan_remove(struct pcmcia_device *pdev)
+{
+ pcan_free(pdev);
+ pcmcia_disable_device(pdev);
+}
+
+static struct pcmcia_driver pcan_driver = {
+ .name = PCC_NAME,
+ .probe = pcan_probe,
+ .remove = pcan_remove,
+ .id_table = pcan_table,
+};
+module_pcmcia_driver(pcan_driver);
diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c
new file mode 100644
index 000000000..8836a7485
--- /dev/null
+++ b/drivers/net/can/sja1000/plx_pci.c
@@ -0,0 +1,650 @@
+/*
+ * Copyright (C) 2008-2010 Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
+ *
+ * Derived from the ems_pci.c driver:
+ * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
+ * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
+ * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/can/dev.h>
+#include <linux/io.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "sja1000_plx_pci"
+
+MODULE_AUTHOR("Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>");
+MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with "
+ "the SJA1000 chips");
+MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, "
+ "Adlink PCI-7841/cPCI-7841 SE, "
+ "Marathon CAN-bus-PCI, "
+ "TEWS TECHNOLOGIES TPMC810, "
+ "esd CAN-PCI/CPCI/PCI104/200, "
+ "esd CAN-PCI/PMC/266, "
+ "esd CAN-PCIe/2000, "
+ "Connect Tech Inc. CANpro/104-Plus Opto (CRG001), "
+ "IXXAT PC-I 04/PCI, "
+ "ELCUS CAN-200-PCI")
+MODULE_LICENSE("GPL v2");
+
+#define PLX_PCI_MAX_CHAN 2
+
+struct plx_pci_card {
+ int channels; /* detected channels count */
+ struct net_device *net_dev[PLX_PCI_MAX_CHAN];
+ void __iomem *conf_addr;
+
+ /* Pointer to device-dependent reset function */
+ void (*reset_func)(struct pci_dev *pdev);
+};
+
+#define PLX_PCI_CAN_CLOCK (16000000 / 2)
+
+/* PLX9030/9050/9052 registers */
+#define PLX_INTCSR 0x4c /* Interrupt Control/Status */
+#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
+ * Serial EEPROM, and Initialization
+ * Control register
+ */
+
+#define PLX_LINT1_EN 0x1 /* Local interrupt 1 enable */
+#define PLX_LINT2_EN (1 << 3) /* Local interrupt 2 enable */
+#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
+#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
+
+/* PLX9056 registers */
+#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
+#define PLX9056_CNTRL 0x6c /* Control / Software Reset */
+
+#define PLX9056_LINTI (1 << 11)
+#define PLX9056_PCI_INT_EN (1 << 8)
+#define PLX9056_PCI_RCR (1 << 29) /* Read Configuration Registers */
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode, push-pull and the correct polarity.
+ */
+#define PLX_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 7
+ * (meaning direct oscillator output) because the second SJA1000 chip
+ * is driven by the first one CLKOUT output.
+ */
+#define PLX_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
+
+/* SJA1000 Control Register in the BasicCAN Mode */
+#define REG_CR 0x00
+
+/* States of some SJA1000 registers after hardware reset in the BasicCAN mode*/
+#define REG_CR_BASICCAN_INITIAL 0x21
+#define REG_CR_BASICCAN_INITIAL_MASK 0xa1
+#define REG_SR_BASICCAN_INITIAL 0x0c
+#define REG_IR_BASICCAN_INITIAL 0xe0
+
+/* States of some SJA1000 registers after hardware reset in the PeliCAN mode*/
+#define REG_MOD_PELICAN_INITIAL 0x01
+#define REG_SR_PELICAN_INITIAL 0x3c
+#define REG_IR_PELICAN_INITIAL 0x00
+
+#define ADLINK_PCI_VENDOR_ID 0x144A
+#define ADLINK_PCI_DEVICE_ID 0x7841
+
+#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
+#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
+#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
+#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
+#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
+#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
+
+#define CAN200PCI_DEVICE_ID 0x9030
+#define CAN200PCI_VENDOR_ID 0x10b5
+#define CAN200PCI_SUB_DEVICE_ID 0x0301
+#define CAN200PCI_SUB_VENDOR_ID 0xe1c5
+
+#define IXXAT_PCI_VENDOR_ID 0x10b5
+#define IXXAT_PCI_DEVICE_ID 0x9050
+#define IXXAT_PCI_SUB_SYS_ID 0x2540
+
+#define MARATHON_PCI_DEVICE_ID 0x2715
+
+#define TEWS_PCI_VENDOR_ID 0x1498
+#define TEWS_PCI_DEVICE_ID_TMPC810 0x032A
+
+#define CTI_PCI_VENDOR_ID 0x12c4
+#define CTI_PCI_DEVICE_ID_CRG001 0x0900
+
+static void plx_pci_reset_common(struct pci_dev *pdev);
+static void plx_pci_reset_marathon(struct pci_dev *pdev);
+static void plx9056_pci_reset_common(struct pci_dev *pdev);
+
+struct plx_pci_channel_map {
+ u32 bar;
+ u32 offset;
+ u32 size; /* 0x00 - auto, e.g. length of entire bar */
+};
+
+struct plx_pci_card_info {
+ const char *name;
+ int channel_count;
+ u32 can_clock;
+ u8 ocr; /* output control register */
+ u8 cdr; /* clock divider register */
+
+ /* Parameters for mapping local configuration space */
+ struct plx_pci_channel_map conf_map;
+
+ /* Parameters for mapping the SJA1000 chips */
+ struct plx_pci_channel_map chan_map_tbl[PLX_PCI_MAX_CHAN];
+
+ /* Pointer to device-dependent reset function */
+ void (*reset_func)(struct pci_dev *pdev);
+};
+
+static struct plx_pci_card_info plx_pci_card_info_adlink = {
+ "Adlink PCI-7841/cPCI-7841", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9052 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_adlink_se = {
+ "Adlink PCI-7841/cPCI-7841 SE", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9052 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_esd200 = {
+ "esd CAN-PCI/CPCI/PCI104/200", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9030/9050 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_esd266 = {
+ "esd CAN-PCI/PMC/266", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx9056_pci_reset_common
+ /* based on PLX9056 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_esd2000 = {
+ "esd CAN-PCIe/2000", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx9056_pci_reset_common
+ /* based on PEX8311 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_ixxat = {
+ "IXXAT PC-I 04/PCI", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x200, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9050 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_marathon = {
+ "Marathon CAN-bus-PCI", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} },
+ &plx_pci_reset_marathon
+ /* based on PLX9052 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_tews = {
+ "TEWS TECHNOLOGIES TPMC810", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9030 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_cti = {
+ "Connect Tech Inc. CANpro/104-Plus Opto (CRG001)", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9030 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_elcus = {
+ "Eclus CAN-200-PCI", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {3, 0x00, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9030 */
+};
+
+static const struct pci_device_id plx_pci_tbl[] = {
+ {
+ /* Adlink PCI-7841/cPCI-7841 */
+ ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
+ PCI_ANY_ID, PCI_ANY_ID,
+ PCI_CLASS_NETWORK_OTHER << 8, ~0,
+ (kernel_ulong_t)&plx_pci_card_info_adlink
+ },
+ {
+ /* Adlink PCI-7841/cPCI-7841 SE */
+ ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
+ PCI_ANY_ID, PCI_ANY_ID,
+ PCI_CLASS_COMMUNICATION_OTHER << 8, ~0,
+ (kernel_ulong_t)&plx_pci_card_info_adlink_se
+ },
+ {
+ /* esd CAN-PCI/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-CPCI/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-PCI104/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-PCI/266 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd266
+ },
+ {
+ /* esd CAN-PMC/266 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd266
+ },
+ {
+ /* esd CAN-PCIE/2000 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd2000
+ },
+ {
+ /* IXXAT PC-I 04/PCI card */
+ IXXAT_PCI_VENDOR_ID, IXXAT_PCI_DEVICE_ID,
+ PCI_ANY_ID, IXXAT_PCI_SUB_SYS_ID,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_ixxat
+ },
+ {
+ /* Marathon CAN-bus-PCI card */
+ PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_marathon
+ },
+ {
+ /* TEWS TECHNOLOGIES TPMC810 card */
+ TEWS_PCI_VENDOR_ID, TEWS_PCI_DEVICE_ID_TMPC810,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_tews
+ },
+ {
+ /* Connect Tech Inc. CANpro/104-Plus Opto (CRG001) card */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ CTI_PCI_VENDOR_ID, CTI_PCI_DEVICE_ID_CRG001,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_cti
+ },
+ {
+ /* Elcus CAN-200-PCI */
+ CAN200PCI_VENDOR_ID, CAN200PCI_DEVICE_ID,
+ CAN200PCI_SUB_VENDOR_ID, CAN200PCI_SUB_DEVICE_ID,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_elcus
+ },
+ { 0,}
+};
+MODULE_DEVICE_TABLE(pci, plx_pci_tbl);
+
+static u8 plx_pci_read_reg(const struct sja1000_priv *priv, int port)
+{
+ return ioread8(priv->reg_base + port);
+}
+
+static void plx_pci_write_reg(const struct sja1000_priv *priv, int port, u8 val)
+{
+ iowrite8(val, priv->reg_base + port);
+}
+
+/*
+ * Check if a CAN controller is present at the specified location
+ * by trying to switch 'em from the Basic mode into the PeliCAN mode.
+ * Also check states of some registers in reset mode.
+ */
+static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
+{
+ int flag = 0;
+
+ /*
+ * Check registers after hardware reset (the Basic mode)
+ * See states on p. 10 of the Datasheet.
+ */
+ if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) ==
+ REG_CR_BASICCAN_INITIAL &&
+ (priv->read_reg(priv, SJA1000_SR) == REG_SR_BASICCAN_INITIAL) &&
+ (priv->read_reg(priv, SJA1000_IR) == REG_IR_BASICCAN_INITIAL))
+ flag = 1;
+
+ /* Bring the SJA1000 into the PeliCAN mode*/
+ priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
+
+ /*
+ * Check registers after reset in the PeliCAN mode.
+ * See states on p. 23 of the Datasheet.
+ */
+ if (priv->read_reg(priv, SJA1000_MOD) == REG_MOD_PELICAN_INITIAL &&
+ priv->read_reg(priv, SJA1000_SR) == REG_SR_PELICAN_INITIAL &&
+ priv->read_reg(priv, SJA1000_IR) == REG_IR_PELICAN_INITIAL)
+ return flag;
+
+ return 0;
+}
+
+/*
+ * PLX9030/50/52 software reset
+ * Also LRESET# asserts and brings to reset device on the Local Bus (if wired).
+ * For most cards it's enough for reset the SJA1000 chips.
+ */
+static void plx_pci_reset_common(struct pci_dev *pdev)
+{
+ struct plx_pci_card *card = pci_get_drvdata(pdev);
+ u32 cntrl;
+
+ cntrl = ioread32(card->conf_addr + PLX_CNTRL);
+ cntrl |= PLX_PCI_RESET;
+ iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
+ udelay(100);
+ cntrl ^= PLX_PCI_RESET;
+ iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
+};
+
+/*
+ * PLX9056 software reset
+ * Assert LRESET# and reset device(s) on the Local Bus (if wired).
+ */
+static void plx9056_pci_reset_common(struct pci_dev *pdev)
+{
+ struct plx_pci_card *card = pci_get_drvdata(pdev);
+ u32 cntrl;
+
+ /* issue a local bus reset */
+ cntrl = ioread32(card->conf_addr + PLX9056_CNTRL);
+ cntrl |= PLX_PCI_RESET;
+ iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
+ udelay(100);
+ cntrl ^= PLX_PCI_RESET;
+ iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
+
+ /* reload local configuration from EEPROM */
+ cntrl |= PLX9056_PCI_RCR;
+ iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
+
+ /*
+ * There is no safe way to poll for the end
+ * of reconfiguration process. Waiting for 10ms
+ * is safe.
+ */
+ mdelay(10);
+
+ cntrl ^= PLX9056_PCI_RCR;
+ iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
+};
+
+/* Special reset function for Marathon card */
+static void plx_pci_reset_marathon(struct pci_dev *pdev)
+{
+ void __iomem *reset_addr;
+ int i;
+ static const int reset_bar[2] = {3, 5};
+
+ plx_pci_reset_common(pdev);
+
+ for (i = 0; i < 2; i++) {
+ reset_addr = pci_iomap(pdev, reset_bar[i], 0);
+ if (!reset_addr) {
+ dev_err(&pdev->dev, "Failed to remap reset "
+ "space %d (BAR%d)\n", i, reset_bar[i]);
+ } else {
+ /* reset the SJA1000 chip */
+ iowrite8(0x1, reset_addr);
+ udelay(100);
+ pci_iounmap(pdev, reset_addr);
+ }
+ }
+}
+
+static void plx_pci_del_card(struct pci_dev *pdev)
+{
+ struct plx_pci_card *card = pci_get_drvdata(pdev);
+ struct net_device *dev;
+ struct sja1000_priv *priv;
+ int i = 0;
+
+ for (i = 0; i < PLX_PCI_MAX_CHAN; i++) {
+ dev = card->net_dev[i];
+ if (!dev)
+ continue;
+
+ dev_info(&pdev->dev, "Removing %s\n", dev->name);
+ unregister_sja1000dev(dev);
+ priv = netdev_priv(dev);
+ if (priv->reg_base)
+ pci_iounmap(pdev, priv->reg_base);
+ free_sja1000dev(dev);
+ }
+
+ card->reset_func(pdev);
+
+ /*
+ * Disable interrupts from PCI-card and disable local
+ * interrupts
+ */
+ if (pdev->device != PCI_DEVICE_ID_PLX_9056)
+ iowrite32(0x0, card->conf_addr + PLX_INTCSR);
+ else
+ iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
+
+ if (card->conf_addr)
+ pci_iounmap(pdev, card->conf_addr);
+
+ kfree(card);
+
+ pci_disable_device(pdev);
+}
+
+/*
+ * Probe PLX90xx based device for the SJA1000 chips and register each
+ * available CAN channel to SJA1000 Socket-CAN subsystem.
+ */
+static int plx_pci_add_card(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct sja1000_priv *priv;
+ struct net_device *dev;
+ struct plx_pci_card *card;
+ struct plx_pci_card_info *ci;
+ int err, i;
+ u32 val;
+ void __iomem *addr;
+
+ ci = (struct plx_pci_card_info *)ent->driver_data;
+
+ if (pci_enable_device(pdev) < 0) {
+ dev_err(&pdev->dev, "Failed to enable PCI device\n");
+ return -ENODEV;
+ }
+
+ dev_info(&pdev->dev, "Detected \"%s\" card at slot #%i\n",
+ ci->name, PCI_SLOT(pdev->devfn));
+
+ /* Allocate card structures to hold addresses, ... */
+ card = kzalloc(sizeof(*card), GFP_KERNEL);
+ if (!card) {
+ pci_disable_device(pdev);
+ return -ENOMEM;
+ }
+
+ pci_set_drvdata(pdev, card);
+
+ card->channels = 0;
+
+ /* Remap PLX90xx configuration space */
+ addr = pci_iomap(pdev, ci->conf_map.bar, ci->conf_map.size);
+ if (!addr) {
+ err = -ENOMEM;
+ dev_err(&pdev->dev, "Failed to remap configuration space "
+ "(BAR%d)\n", ci->conf_map.bar);
+ goto failure_cleanup;
+ }
+ card->conf_addr = addr + ci->conf_map.offset;
+
+ ci->reset_func(pdev);
+ card->reset_func = ci->reset_func;
+
+ /* Detect available channels */
+ for (i = 0; i < ci->channel_count; i++) {
+ struct plx_pci_channel_map *cm = &ci->chan_map_tbl[i];
+
+ dev = alloc_sja1000dev(0);
+ if (!dev) {
+ err = -ENOMEM;
+ goto failure_cleanup;
+ }
+
+ card->net_dev[i] = dev;
+ priv = netdev_priv(dev);
+ priv->priv = card;
+ priv->irq_flags = IRQF_SHARED;
+
+ dev->irq = pdev->irq;
+
+ /*
+ * Remap IO space of the SJA1000 chips
+ * This is device-dependent mapping
+ */
+ addr = pci_iomap(pdev, cm->bar, cm->size);
+ if (!addr) {
+ err = -ENOMEM;
+ dev_err(&pdev->dev, "Failed to remap BAR%d\n", cm->bar);
+ goto failure_cleanup;
+ }
+
+ priv->reg_base = addr + cm->offset;
+ priv->read_reg = plx_pci_read_reg;
+ priv->write_reg = plx_pci_write_reg;
+
+ /* Check if channel is present */
+ if (plx_pci_check_sja1000(priv)) {
+ priv->can.clock.freq = ci->can_clock;
+ priv->ocr = ci->ocr;
+ priv->cdr = ci->cdr;
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = i;
+
+ /* Register SJA1000 device */
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "Registering device failed "
+ "(err=%d)\n", err);
+ goto failure_cleanup;
+ }
+
+ card->channels++;
+
+ dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d "
+ "registered as %s\n", i + 1, priv->reg_base,
+ dev->irq, dev->name);
+ } else {
+ dev_err(&pdev->dev, "Channel #%d not detected\n",
+ i + 1);
+ free_sja1000dev(dev);
+ card->net_dev[i] = NULL;
+ }
+ }
+
+ if (!card->channels) {
+ err = -ENODEV;
+ goto failure_cleanup;
+ }
+
+ /*
+ * Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
+ * Local_2 interrupts from the SJA1000 chips
+ */
+ if (pdev->device != PCI_DEVICE_ID_PLX_9056) {
+ val = ioread32(card->conf_addr + PLX_INTCSR);
+ if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
+ val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
+ else
+ val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
+ iowrite32(val, card->conf_addr + PLX_INTCSR);
+ } else {
+ iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
+ card->conf_addr + PLX9056_INTCSR);
+ }
+ return 0;
+
+failure_cleanup:
+ dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
+
+ plx_pci_del_card(pdev);
+
+ return err;
+}
+
+static struct pci_driver plx_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = plx_pci_tbl,
+ .probe = plx_pci_add_card,
+ .remove = plx_pci_del_card,
+};
+
+module_pci_driver(plx_pci_driver);
diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c
new file mode 100644
index 000000000..32bd7f451
--- /dev/null
+++ b/drivers/net/can/sja1000/sja1000.c
@@ -0,0 +1,704 @@
+/*
+ * sja1000.c - Philips SJA1000 network device driver
+ *
+ * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
+ * 38106 Braunschweig, GERMANY
+ *
+ * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of Volkswagen nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * Alternatively, provided that this notice is retained in full, this
+ * software may be distributed under the terms of the GNU General
+ * Public License ("GPL") version 2, in which case the provisions of the
+ * GPL apply INSTEAD OF those given above.
+ *
+ * The provided data structures and external interfaces from this code
+ * are not restricted to be used by modules with a GPL compatible license.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
+ * DAMAGE.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+#include <linux/fcntl.h>
+#include <linux/interrupt.h>
+#include <linux/ptrace.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/netdevice.h>
+#include <linux/if_arp.h>
+#include <linux/if_ether.h>
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+#include <linux/can/led.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "sja1000"
+
+MODULE_AUTHOR("Oliver Hartkopp <oliver.hartkopp@volkswagen.de>");
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_DESCRIPTION(DRV_NAME "CAN netdevice driver");
+
+static const struct can_bittiming_const sja1000_bittiming_const = {
+ .name = DRV_NAME,
+ .tseg1_min = 1,
+ .tseg1_max = 16,
+ .tseg2_min = 1,
+ .tseg2_max = 8,
+ .sjw_max = 4,
+ .brp_min = 1,
+ .brp_max = 64,
+ .brp_inc = 1,
+};
+
+static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val)
+{
+ unsigned long flags;
+
+ /*
+ * The command register needs some locking and time to settle
+ * the write_reg() operation - especially on SMP systems.
+ */
+ spin_lock_irqsave(&priv->cmdreg_lock, flags);
+ priv->write_reg(priv, SJA1000_CMR, val);
+ priv->read_reg(priv, SJA1000_SR);
+ spin_unlock_irqrestore(&priv->cmdreg_lock, flags);
+}
+
+static int sja1000_is_absent(struct sja1000_priv *priv)
+{
+ return (priv->read_reg(priv, SJA1000_MOD) == 0xFF);
+}
+
+static int sja1000_probe_chip(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+
+ if (priv->reg_base && sja1000_is_absent(priv)) {
+ netdev_err(dev, "probing failed\n");
+ return 0;
+ }
+ return -1;
+}
+
+static void set_reset_mode(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ unsigned char status = priv->read_reg(priv, SJA1000_MOD);
+ int i;
+
+ /* disable interrupts */
+ priv->write_reg(priv, SJA1000_IER, IRQ_OFF);
+
+ for (i = 0; i < 100; i++) {
+ /* check reset bit */
+ if (status & MOD_RM) {
+ priv->can.state = CAN_STATE_STOPPED;
+ return;
+ }
+
+ /* reset chip */
+ priv->write_reg(priv, SJA1000_MOD, MOD_RM);
+ udelay(10);
+ status = priv->read_reg(priv, SJA1000_MOD);
+ }
+
+ netdev_err(dev, "setting SJA1000 into reset mode failed!\n");
+}
+
+static void set_normal_mode(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ unsigned char status = priv->read_reg(priv, SJA1000_MOD);
+ u8 mod_reg_val = 0x00;
+ int i;
+
+ for (i = 0; i < 100; i++) {
+ /* check reset bit */
+ if ((status & MOD_RM) == 0) {
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+ /* enable interrupts */
+ if (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)
+ priv->write_reg(priv, SJA1000_IER, IRQ_ALL);
+ else
+ priv->write_reg(priv, SJA1000_IER,
+ IRQ_ALL & ~IRQ_BEI);
+ return;
+ }
+
+ /* set chip to normal mode */
+ if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)
+ mod_reg_val |= MOD_LOM;
+ if (priv->can.ctrlmode & CAN_CTRLMODE_PRESUME_ACK)
+ mod_reg_val |= MOD_STM;
+ priv->write_reg(priv, SJA1000_MOD, mod_reg_val);
+
+ udelay(10);
+
+ status = priv->read_reg(priv, SJA1000_MOD);
+ }
+
+ netdev_err(dev, "setting SJA1000 into normal mode failed!\n");
+}
+
+/*
+ * initialize SJA1000 chip:
+ * - reset chip
+ * - set output mode
+ * - set baudrate
+ * - enable interrupts
+ * - start operating mode
+ */
+static void chipset_init(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+
+ /* set clock divider and output control register */
+ priv->write_reg(priv, SJA1000_CDR, priv->cdr | CDR_PELICAN);
+
+ /* set acceptance filter (accept all) */
+ priv->write_reg(priv, SJA1000_ACCC0, 0x00);
+ priv->write_reg(priv, SJA1000_ACCC1, 0x00);
+ priv->write_reg(priv, SJA1000_ACCC2, 0x00);
+ priv->write_reg(priv, SJA1000_ACCC3, 0x00);
+
+ priv->write_reg(priv, SJA1000_ACCM0, 0xFF);
+ priv->write_reg(priv, SJA1000_ACCM1, 0xFF);
+ priv->write_reg(priv, SJA1000_ACCM2, 0xFF);
+ priv->write_reg(priv, SJA1000_ACCM3, 0xFF);
+
+ priv->write_reg(priv, SJA1000_OCR, priv->ocr | OCR_MODE_NORMAL);
+}
+
+static void sja1000_start(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+
+ /* leave reset mode */
+ if (priv->can.state != CAN_STATE_STOPPED)
+ set_reset_mode(dev);
+
+ /* Initialize chip if uninitialized at this stage */
+ if (!(priv->read_reg(priv, SJA1000_CDR) & CDR_PELICAN))
+ chipset_init(dev);
+
+ /* Clear error counters and error code capture */
+ priv->write_reg(priv, SJA1000_TXERR, 0x0);
+ priv->write_reg(priv, SJA1000_RXERR, 0x0);
+ priv->read_reg(priv, SJA1000_ECC);
+
+ /* leave reset mode */
+ set_normal_mode(dev);
+}
+
+static int sja1000_set_mode(struct net_device *dev, enum can_mode mode)
+{
+ switch (mode) {
+ case CAN_MODE_START:
+ sja1000_start(dev);
+ if (netif_queue_stopped(dev))
+ netif_wake_queue(dev);
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ return 0;
+}
+
+static int sja1000_set_bittiming(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct can_bittiming *bt = &priv->can.bittiming;
+ u8 btr0, btr1;
+
+ btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6);
+ btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) |
+ (((bt->phase_seg2 - 1) & 0x7) << 4);
+ if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+ btr1 |= 0x80;
+
+ netdev_info(dev, "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
+
+ priv->write_reg(priv, SJA1000_BTR0, btr0);
+ priv->write_reg(priv, SJA1000_BTR1, btr1);
+
+ return 0;
+}
+
+static int sja1000_get_berr_counter(const struct net_device *dev,
+ struct can_berr_counter *bec)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+
+ bec->txerr = priv->read_reg(priv, SJA1000_TXERR);
+ bec->rxerr = priv->read_reg(priv, SJA1000_RXERR);
+
+ return 0;
+}
+
+/*
+ * transmit a CAN message
+ * message layout in the sk_buff should be like this:
+ * xx xx xx xx ff ll 00 11 22 33 44 55 66 77
+ * [ can-id ] [flags] [len] [can data (up to 8 bytes]
+ */
+static netdev_tx_t sja1000_start_xmit(struct sk_buff *skb,
+ struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct can_frame *cf = (struct can_frame *)skb->data;
+ uint8_t fi;
+ uint8_t dlc;
+ canid_t id;
+ uint8_t dreg;
+ u8 cmd_reg_val = 0x00;
+ int i;
+
+ if (can_dropped_invalid_skb(dev, skb))
+ return NETDEV_TX_OK;
+
+ netif_stop_queue(dev);
+
+ fi = dlc = cf->can_dlc;
+ id = cf->can_id;
+
+ if (id & CAN_RTR_FLAG)
+ fi |= SJA1000_FI_RTR;
+
+ if (id & CAN_EFF_FLAG) {
+ fi |= SJA1000_FI_FF;
+ dreg = SJA1000_EFF_BUF;
+ priv->write_reg(priv, SJA1000_FI, fi);
+ priv->write_reg(priv, SJA1000_ID1, (id & 0x1fe00000) >> 21);
+ priv->write_reg(priv, SJA1000_ID2, (id & 0x001fe000) >> 13);
+ priv->write_reg(priv, SJA1000_ID3, (id & 0x00001fe0) >> 5);
+ priv->write_reg(priv, SJA1000_ID4, (id & 0x0000001f) << 3);
+ } else {
+ dreg = SJA1000_SFF_BUF;
+ priv->write_reg(priv, SJA1000_FI, fi);
+ priv->write_reg(priv, SJA1000_ID1, (id & 0x000007f8) >> 3);
+ priv->write_reg(priv, SJA1000_ID2, (id & 0x00000007) << 5);
+ }
+
+ for (i = 0; i < dlc; i++)
+ priv->write_reg(priv, dreg++, cf->data[i]);
+
+ can_put_echo_skb(skb, dev, 0);
+
+ if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT)
+ cmd_reg_val |= CMD_AT;
+
+ if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK)
+ cmd_reg_val |= CMD_SRR;
+ else
+ cmd_reg_val |= CMD_TR;
+
+ sja1000_write_cmdreg(priv, cmd_reg_val);
+
+ return NETDEV_TX_OK;
+}
+
+static void sja1000_rx(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct net_device_stats *stats = &dev->stats;
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ uint8_t fi;
+ uint8_t dreg;
+ canid_t id;
+ int i;
+
+ /* create zero'ed CAN frame buffer */
+ skb = alloc_can_skb(dev, &cf);
+ if (skb == NULL)
+ return;
+
+ fi = priv->read_reg(priv, SJA1000_FI);
+
+ if (fi & SJA1000_FI_FF) {
+ /* extended frame format (EFF) */
+ dreg = SJA1000_EFF_BUF;
+ id = (priv->read_reg(priv, SJA1000_ID1) << 21)
+ | (priv->read_reg(priv, SJA1000_ID2) << 13)
+ | (priv->read_reg(priv, SJA1000_ID3) << 5)
+ | (priv->read_reg(priv, SJA1000_ID4) >> 3);
+ id |= CAN_EFF_FLAG;
+ } else {
+ /* standard frame format (SFF) */
+ dreg = SJA1000_SFF_BUF;
+ id = (priv->read_reg(priv, SJA1000_ID1) << 3)
+ | (priv->read_reg(priv, SJA1000_ID2) >> 5);
+ }
+
+ cf->can_dlc = get_can_dlc(fi & 0x0F);
+ if (fi & SJA1000_FI_RTR) {
+ id |= CAN_RTR_FLAG;
+ } else {
+ for (i = 0; i < cf->can_dlc; i++)
+ cf->data[i] = priv->read_reg(priv, dreg++);
+ }
+
+ cf->can_id = id;
+
+ /* release receive buffer */
+ sja1000_write_cmdreg(priv, CMD_RRB);
+
+ netif_rx(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+
+ can_led_event(dev, CAN_LED_EVENT_RX);
+}
+
+static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct net_device_stats *stats = &dev->stats;
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ enum can_state state = priv->can.state;
+ enum can_state rx_state, tx_state;
+ unsigned int rxerr, txerr;
+ uint8_t ecc, alc;
+
+ skb = alloc_can_err_skb(dev, &cf);
+ if (skb == NULL)
+ return -ENOMEM;
+
+ txerr = priv->read_reg(priv, SJA1000_TXERR);
+ rxerr = priv->read_reg(priv, SJA1000_RXERR);
+
+ cf->data[6] = txerr;
+ cf->data[7] = rxerr;
+
+ if (isrc & IRQ_DOI) {
+ /* data overrun interrupt */
+ netdev_dbg(dev, "data overrun interrupt\n");
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+ stats->rx_over_errors++;
+ stats->rx_errors++;
+ sja1000_write_cmdreg(priv, CMD_CDO); /* clear bit */
+ }
+
+ if (isrc & IRQ_EI) {
+ /* error warning interrupt */
+ netdev_dbg(dev, "error warning interrupt\n");
+
+ if (status & SR_BS)
+ state = CAN_STATE_BUS_OFF;
+ else if (status & SR_ES)
+ state = CAN_STATE_ERROR_WARNING;
+ else
+ state = CAN_STATE_ERROR_ACTIVE;
+ }
+ if (isrc & IRQ_BEI) {
+ /* bus error interrupt */
+ priv->can.can_stats.bus_error++;
+ stats->rx_errors++;
+
+ ecc = priv->read_reg(priv, SJA1000_ECC);
+
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+
+ switch (ecc & ECC_MASK) {
+ case ECC_BIT:
+ cf->data[2] |= CAN_ERR_PROT_BIT;
+ break;
+ case ECC_FORM:
+ cf->data[2] |= CAN_ERR_PROT_FORM;
+ break;
+ case ECC_STUFF:
+ cf->data[2] |= CAN_ERR_PROT_STUFF;
+ break;
+ default:
+ cf->data[2] |= CAN_ERR_PROT_UNSPEC;
+ cf->data[3] = ecc & ECC_SEG;
+ break;
+ }
+ /* Error occurred during transmission? */
+ if ((ecc & ECC_DIR) == 0)
+ cf->data[2] |= CAN_ERR_PROT_TX;
+ }
+ if (isrc & IRQ_EPI) {
+ /* error passive interrupt */
+ netdev_dbg(dev, "error passive interrupt\n");
+
+ if (state == CAN_STATE_ERROR_PASSIVE)
+ state = CAN_STATE_ERROR_WARNING;
+ else
+ state = CAN_STATE_ERROR_PASSIVE;
+ }
+ if (isrc & IRQ_ALI) {
+ /* arbitration lost interrupt */
+ netdev_dbg(dev, "arbitration lost interrupt\n");
+ alc = priv->read_reg(priv, SJA1000_ALC);
+ priv->can.can_stats.arbitration_lost++;
+ stats->tx_errors++;
+ cf->can_id |= CAN_ERR_LOSTARB;
+ cf->data[0] = alc & 0x1f;
+ }
+
+ if (state != priv->can.state) {
+ tx_state = txerr >= rxerr ? state : 0;
+ rx_state = txerr <= rxerr ? state : 0;
+
+ can_change_state(dev, cf, tx_state, rx_state);
+
+ if(state == CAN_STATE_BUS_OFF)
+ can_bus_off(dev);
+ }
+
+ netif_rx(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+
+ return 0;
+}
+
+irqreturn_t sja1000_interrupt(int irq, void *dev_id)
+{
+ struct net_device *dev = (struct net_device *)dev_id;
+ struct sja1000_priv *priv = netdev_priv(dev);
+ struct net_device_stats *stats = &dev->stats;
+ uint8_t isrc, status;
+ int n = 0;
+
+ if (priv->pre_irq)
+ priv->pre_irq(priv);
+
+ /* Shared interrupts and IRQ off? */
+ if (priv->read_reg(priv, SJA1000_IER) == IRQ_OFF)
+ goto out;
+
+ while ((isrc = priv->read_reg(priv, SJA1000_IR)) &&
+ (n < SJA1000_MAX_IRQ)) {
+
+ status = priv->read_reg(priv, SJA1000_SR);
+ /* check for absent controller due to hw unplug */
+ if (status == 0xFF && sja1000_is_absent(priv))
+ goto out;
+
+ if (isrc & IRQ_WUI)
+ netdev_warn(dev, "wakeup interrupt\n");
+
+ if (isrc & IRQ_TI) {
+ /* transmission buffer released */
+ if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT &&
+ !(status & SR_TCS)) {
+ stats->tx_errors++;
+ can_free_echo_skb(dev, 0);
+ } else {
+ /* transmission complete */
+ stats->tx_bytes +=
+ priv->read_reg(priv, SJA1000_FI) & 0xf;
+ stats->tx_packets++;
+ can_get_echo_skb(dev, 0);
+ }
+ netif_wake_queue(dev);
+ can_led_event(dev, CAN_LED_EVENT_TX);
+ }
+ if (isrc & IRQ_RI) {
+ /* receive interrupt */
+ while (status & SR_RBS) {
+ sja1000_rx(dev);
+ status = priv->read_reg(priv, SJA1000_SR);
+ /* check for absent controller */
+ if (status == 0xFF && sja1000_is_absent(priv))
+ goto out;
+ }
+ }
+ if (isrc & (IRQ_DOI | IRQ_EI | IRQ_BEI | IRQ_EPI | IRQ_ALI)) {
+ /* error interrupt */
+ if (sja1000_err(dev, isrc, status))
+ break;
+ }
+ n++;
+ }
+out:
+ if (priv->post_irq)
+ priv->post_irq(priv);
+
+ if (n >= SJA1000_MAX_IRQ)
+ netdev_dbg(dev, "%d messages handled in ISR", n);
+
+ return (n) ? IRQ_HANDLED : IRQ_NONE;
+}
+EXPORT_SYMBOL_GPL(sja1000_interrupt);
+
+static int sja1000_open(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+ int err;
+
+ /* set chip into reset mode */
+ set_reset_mode(dev);
+
+ /* common open */
+ err = open_candev(dev);
+ if (err)
+ return err;
+
+ /* register interrupt handler, if not done by the device driver */
+ if (!(priv->flags & SJA1000_CUSTOM_IRQ_HANDLER)) {
+ err = request_irq(dev->irq, sja1000_interrupt, priv->irq_flags,
+ dev->name, (void *)dev);
+ if (err) {
+ close_candev(dev);
+ return -EAGAIN;
+ }
+ }
+
+ /* init and start chi */
+ sja1000_start(dev);
+
+ can_led_event(dev, CAN_LED_EVENT_OPEN);
+
+ netif_start_queue(dev);
+
+ return 0;
+}
+
+static int sja1000_close(struct net_device *dev)
+{
+ struct sja1000_priv *priv = netdev_priv(dev);
+
+ netif_stop_queue(dev);
+ set_reset_mode(dev);
+
+ if (!(priv->flags & SJA1000_CUSTOM_IRQ_HANDLER))
+ free_irq(dev->irq, (void *)dev);
+
+ close_candev(dev);
+
+ can_led_event(dev, CAN_LED_EVENT_STOP);
+
+ return 0;
+}
+
+struct net_device *alloc_sja1000dev(int sizeof_priv)
+{
+ struct net_device *dev;
+ struct sja1000_priv *priv;
+
+ dev = alloc_candev(sizeof(struct sja1000_priv) + sizeof_priv,
+ SJA1000_ECHO_SKB_MAX);
+ if (!dev)
+ return NULL;
+
+ priv = netdev_priv(dev);
+
+ priv->dev = dev;
+ priv->can.bittiming_const = &sja1000_bittiming_const;
+ priv->can.do_set_bittiming = sja1000_set_bittiming;
+ priv->can.do_set_mode = sja1000_set_mode;
+ priv->can.do_get_berr_counter = sja1000_get_berr_counter;
+ priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK |
+ CAN_CTRLMODE_LISTENONLY |
+ CAN_CTRLMODE_3_SAMPLES |
+ CAN_CTRLMODE_ONE_SHOT |
+ CAN_CTRLMODE_BERR_REPORTING |
+ CAN_CTRLMODE_PRESUME_ACK;
+
+ spin_lock_init(&priv->cmdreg_lock);
+
+ if (sizeof_priv)
+ priv->priv = (void *)priv + sizeof(struct sja1000_priv);
+
+ return dev;
+}
+EXPORT_SYMBOL_GPL(alloc_sja1000dev);
+
+void free_sja1000dev(struct net_device *dev)
+{
+ free_candev(dev);
+}
+EXPORT_SYMBOL_GPL(free_sja1000dev);
+
+static const struct net_device_ops sja1000_netdev_ops = {
+ .ndo_open = sja1000_open,
+ .ndo_stop = sja1000_close,
+ .ndo_start_xmit = sja1000_start_xmit,
+ .ndo_change_mtu = can_change_mtu,
+};
+
+int register_sja1000dev(struct net_device *dev)
+{
+ int ret;
+
+ if (!sja1000_probe_chip(dev))
+ return -ENODEV;
+
+ dev->flags |= IFF_ECHO; /* we support local echo */
+ dev->netdev_ops = &sja1000_netdev_ops;
+
+ set_reset_mode(dev);
+ chipset_init(dev);
+
+ ret = register_candev(dev);
+
+ if (!ret)
+ devm_can_led_init(dev);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(register_sja1000dev);
+
+void unregister_sja1000dev(struct net_device *dev)
+{
+ set_reset_mode(dev);
+ unregister_candev(dev);
+}
+EXPORT_SYMBOL_GPL(unregister_sja1000dev);
+
+static __init int sja1000_init(void)
+{
+ printk(KERN_INFO "%s CAN netdevice driver\n", DRV_NAME);
+
+ return 0;
+}
+
+module_init(sja1000_init);
+
+static __exit void sja1000_exit(void)
+{
+ printk(KERN_INFO "%s: driver removed\n", DRV_NAME);
+}
+
+module_exit(sja1000_exit);
diff --git a/drivers/net/can/sja1000/sja1000.h b/drivers/net/can/sja1000/sja1000.h
new file mode 100644
index 000000000..9d46398f8
--- /dev/null
+++ b/drivers/net/can/sja1000/sja1000.h
@@ -0,0 +1,182 @@
+/*
+ * sja1000.h - Philips SJA1000 network device driver
+ *
+ * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
+ * 38106 Braunschweig, GERMANY
+ *
+ * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of Volkswagen nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * Alternatively, provided that this notice is retained in full, this
+ * software may be distributed under the terms of the GNU General
+ * Public License ("GPL") version 2, in which case the provisions of the
+ * GPL apply INSTEAD OF those given above.
+ *
+ * The provided data structures and external interfaces from this code
+ * are not restricted to be used by modules with a GPL compatible license.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
+ * DAMAGE.
+ *
+ */
+
+#ifndef SJA1000_DEV_H
+#define SJA1000_DEV_H
+
+#include <linux/irqreturn.h>
+#include <linux/can/dev.h>
+#include <linux/can/platform/sja1000.h>
+
+#define SJA1000_ECHO_SKB_MAX 1 /* the SJA1000 has one TX buffer object */
+
+#define SJA1000_MAX_IRQ 20 /* max. number of interrupts handled in ISR */
+
+/* SJA1000 registers - manual section 6.4 (Pelican Mode) */
+#define SJA1000_MOD 0x00
+#define SJA1000_CMR 0x01
+#define SJA1000_SR 0x02
+#define SJA1000_IR 0x03
+#define SJA1000_IER 0x04
+#define SJA1000_ALC 0x0B
+#define SJA1000_ECC 0x0C
+#define SJA1000_EWL 0x0D
+#define SJA1000_RXERR 0x0E
+#define SJA1000_TXERR 0x0F
+#define SJA1000_ACCC0 0x10
+#define SJA1000_ACCC1 0x11
+#define SJA1000_ACCC2 0x12
+#define SJA1000_ACCC3 0x13
+#define SJA1000_ACCM0 0x14
+#define SJA1000_ACCM1 0x15
+#define SJA1000_ACCM2 0x16
+#define SJA1000_ACCM3 0x17
+#define SJA1000_RMC 0x1D
+#define SJA1000_RBSA 0x1E
+
+/* Common registers - manual section 6.5 */
+#define SJA1000_BTR0 0x06
+#define SJA1000_BTR1 0x07
+#define SJA1000_OCR 0x08
+#define SJA1000_CDR 0x1F
+
+#define SJA1000_FI 0x10
+#define SJA1000_SFF_BUF 0x13
+#define SJA1000_EFF_BUF 0x15
+
+#define SJA1000_FI_FF 0x80
+#define SJA1000_FI_RTR 0x40
+
+#define SJA1000_ID1 0x11
+#define SJA1000_ID2 0x12
+#define SJA1000_ID3 0x13
+#define SJA1000_ID4 0x14
+
+#define SJA1000_CAN_RAM 0x20
+
+/* mode register */
+#define MOD_RM 0x01
+#define MOD_LOM 0x02
+#define MOD_STM 0x04
+#define MOD_AFM 0x08
+#define MOD_SM 0x10
+
+/* commands */
+#define CMD_SRR 0x10
+#define CMD_CDO 0x08
+#define CMD_RRB 0x04
+#define CMD_AT 0x02
+#define CMD_TR 0x01
+
+/* interrupt sources */
+#define IRQ_BEI 0x80
+#define IRQ_ALI 0x40
+#define IRQ_EPI 0x20
+#define IRQ_WUI 0x10
+#define IRQ_DOI 0x08
+#define IRQ_EI 0x04
+#define IRQ_TI 0x02
+#define IRQ_RI 0x01
+#define IRQ_ALL 0xFF
+#define IRQ_OFF 0x00
+
+/* status register content */
+#define SR_BS 0x80
+#define SR_ES 0x40
+#define SR_TS 0x20
+#define SR_RS 0x10
+#define SR_TCS 0x08
+#define SR_TBS 0x04
+#define SR_DOS 0x02
+#define SR_RBS 0x01
+
+#define SR_CRIT (SR_BS|SR_ES)
+
+/* ECC register */
+#define ECC_SEG 0x1F
+#define ECC_DIR 0x20
+#define ECC_ERR 6
+#define ECC_BIT 0x00
+#define ECC_FORM 0x40
+#define ECC_STUFF 0x80
+#define ECC_MASK 0xc0
+
+/*
+ * Flags for sja1000priv.flags
+ */
+#define SJA1000_CUSTOM_IRQ_HANDLER 0x1
+
+/*
+ * SJA1000 private data structure
+ */
+struct sja1000_priv {
+ struct can_priv can; /* must be the first member */
+ struct sk_buff *echo_skb;
+
+ /* the lower-layer is responsible for appropriate locking */
+ u8 (*read_reg) (const struct sja1000_priv *priv, int reg);
+ void (*write_reg) (const struct sja1000_priv *priv, int reg, u8 val);
+ void (*pre_irq) (const struct sja1000_priv *priv);
+ void (*post_irq) (const struct sja1000_priv *priv);
+
+ void *priv; /* for board-specific data */
+ struct net_device *dev;
+
+ void __iomem *reg_base; /* ioremap'ed address to registers */
+ unsigned long irq_flags; /* for request_irq() */
+ spinlock_t cmdreg_lock; /* lock for concurrent cmd register writes */
+
+ u16 flags; /* custom mode flags */
+ u8 ocr; /* output control register */
+ u8 cdr; /* clock divider register */
+};
+
+struct net_device *alloc_sja1000dev(int sizeof_priv);
+void free_sja1000dev(struct net_device *dev);
+int register_sja1000dev(struct net_device *dev);
+void unregister_sja1000dev(struct net_device *dev);
+
+irqreturn_t sja1000_interrupt(int irq, void *dev_id);
+
+#endif /* SJA1000_DEV_H */
diff --git a/drivers/net/can/sja1000/sja1000_isa.c b/drivers/net/can/sja1000/sja1000_isa.c
new file mode 100644
index 000000000..e97e6d35b
--- /dev/null
+++ b/drivers/net/can/sja1000/sja1000_isa.c
@@ -0,0 +1,323 @@
+/*
+ * Copyright (C) 2009 Wolfgang Grandegger <wg@grandegger.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/can/dev.h>
+#include <linux/can/platform/sja1000.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "sja1000_isa"
+
+#define MAXDEV 8
+
+MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>");
+MODULE_DESCRIPTION("Socket-CAN driver for SJA1000 on the ISA bus");
+MODULE_LICENSE("GPL v2");
+
+#define CLK_DEFAULT 16000000 /* 16 MHz */
+#define CDR_DEFAULT (CDR_CBP | CDR_CLK_OFF)
+#define OCR_DEFAULT OCR_TX0_PUSHPULL
+
+static unsigned long port[MAXDEV];
+static unsigned long mem[MAXDEV];
+static int irq[MAXDEV];
+static int clk[MAXDEV];
+static unsigned char cdr[MAXDEV] = {[0 ... (MAXDEV - 1)] = 0xff};
+static unsigned char ocr[MAXDEV] = {[0 ... (MAXDEV - 1)] = 0xff};
+static int indirect[MAXDEV] = {[0 ... (MAXDEV - 1)] = -1};
+static spinlock_t indirect_lock[MAXDEV]; /* lock for indirect access mode */
+
+module_param_array(port, ulong, NULL, S_IRUGO);
+MODULE_PARM_DESC(port, "I/O port number");
+
+module_param_array(mem, ulong, NULL, S_IRUGO);
+MODULE_PARM_DESC(mem, "I/O memory address");
+
+module_param_array(indirect, int, NULL, S_IRUGO);
+MODULE_PARM_DESC(indirect, "Indirect access via address and data port");
+
+module_param_array(irq, int, NULL, S_IRUGO);
+MODULE_PARM_DESC(irq, "IRQ number");
+
+module_param_array(clk, int, NULL, S_IRUGO);
+MODULE_PARM_DESC(clk, "External oscillator clock frequency "
+ "(default=16000000 [16 MHz])");
+
+module_param_array(cdr, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(cdr, "Clock divider register "
+ "(default=0x48 [CDR_CBP | CDR_CLK_OFF])");
+
+module_param_array(ocr, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(ocr, "Output control register "
+ "(default=0x18 [OCR_TX0_PUSHPULL])");
+
+#define SJA1000_IOSIZE 0x20
+#define SJA1000_IOSIZE_INDIRECT 0x02
+
+static struct platform_device *sja1000_isa_devs[MAXDEV];
+
+static u8 sja1000_isa_mem_read_reg(const struct sja1000_priv *priv, int reg)
+{
+ return readb(priv->reg_base + reg);
+}
+
+static void sja1000_isa_mem_write_reg(const struct sja1000_priv *priv,
+ int reg, u8 val)
+{
+ writeb(val, priv->reg_base + reg);
+}
+
+static u8 sja1000_isa_port_read_reg(const struct sja1000_priv *priv, int reg)
+{
+ return inb((unsigned long)priv->reg_base + reg);
+}
+
+static void sja1000_isa_port_write_reg(const struct sja1000_priv *priv,
+ int reg, u8 val)
+{
+ outb(val, (unsigned long)priv->reg_base + reg);
+}
+
+static u8 sja1000_isa_port_read_reg_indirect(const struct sja1000_priv *priv,
+ int reg)
+{
+ unsigned long flags, base = (unsigned long)priv->reg_base;
+ u8 readval;
+
+ spin_lock_irqsave(&indirect_lock[priv->dev->dev_id], flags);
+ outb(reg, base);
+ readval = inb(base + 1);
+ spin_unlock_irqrestore(&indirect_lock[priv->dev->dev_id], flags);
+
+ return readval;
+}
+
+static void sja1000_isa_port_write_reg_indirect(const struct sja1000_priv *priv,
+ int reg, u8 val)
+{
+ unsigned long flags, base = (unsigned long)priv->reg_base;
+
+ spin_lock_irqsave(&indirect_lock[priv->dev->dev_id], flags);
+ outb(reg, base);
+ outb(val, base + 1);
+ spin_unlock_irqrestore(&indirect_lock[priv->dev->dev_id], flags);
+}
+
+static int sja1000_isa_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct sja1000_priv *priv;
+ void __iomem *base = NULL;
+ int iosize = SJA1000_IOSIZE;
+ int idx = pdev->id;
+ int err;
+
+ dev_dbg(&pdev->dev, "probing idx=%d: port=%#lx, mem=%#lx, irq=%d\n",
+ idx, port[idx], mem[idx], irq[idx]);
+
+ if (mem[idx]) {
+ if (!request_mem_region(mem[idx], iosize, DRV_NAME)) {
+ err = -EBUSY;
+ goto exit;
+ }
+ base = ioremap_nocache(mem[idx], iosize);
+ if (!base) {
+ err = -ENOMEM;
+ goto exit_release;
+ }
+ } else {
+ if (indirect[idx] > 0 ||
+ (indirect[idx] == -1 && indirect[0] > 0))
+ iosize = SJA1000_IOSIZE_INDIRECT;
+ if (!request_region(port[idx], iosize, DRV_NAME)) {
+ err = -EBUSY;
+ goto exit;
+ }
+ }
+
+ dev = alloc_sja1000dev(0);
+ if (!dev) {
+ err = -ENOMEM;
+ goto exit_unmap;
+ }
+ priv = netdev_priv(dev);
+
+ dev->irq = irq[idx];
+ priv->irq_flags = IRQF_SHARED;
+ if (mem[idx]) {
+ priv->reg_base = base;
+ dev->base_addr = mem[idx];
+ priv->read_reg = sja1000_isa_mem_read_reg;
+ priv->write_reg = sja1000_isa_mem_write_reg;
+ } else {
+ priv->reg_base = (void __iomem *)port[idx];
+ dev->base_addr = port[idx];
+
+ if (iosize == SJA1000_IOSIZE_INDIRECT) {
+ priv->read_reg = sja1000_isa_port_read_reg_indirect;
+ priv->write_reg = sja1000_isa_port_write_reg_indirect;
+ spin_lock_init(&indirect_lock[idx]);
+ } else {
+ priv->read_reg = sja1000_isa_port_read_reg;
+ priv->write_reg = sja1000_isa_port_write_reg;
+ }
+ }
+
+ if (clk[idx])
+ priv->can.clock.freq = clk[idx] / 2;
+ else if (clk[0])
+ priv->can.clock.freq = clk[0] / 2;
+ else
+ priv->can.clock.freq = CLK_DEFAULT / 2;
+
+ if (ocr[idx] != 0xff)
+ priv->ocr = ocr[idx];
+ else if (ocr[0] != 0xff)
+ priv->ocr = ocr[0];
+ else
+ priv->ocr = OCR_DEFAULT;
+
+ if (cdr[idx] != 0xff)
+ priv->cdr = cdr[idx];
+ else if (cdr[0] != 0xff)
+ priv->cdr = cdr[0];
+ else
+ priv->cdr = CDR_DEFAULT;
+
+ platform_set_drvdata(pdev, dev);
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ dev->dev_id = idx;
+
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "registering %s failed (err=%d)\n",
+ DRV_NAME, err);
+ goto exit_unmap;
+ }
+
+ dev_info(&pdev->dev, "%s device registered (reg_base=0x%p, irq=%d)\n",
+ DRV_NAME, priv->reg_base, dev->irq);
+ return 0;
+
+ exit_unmap:
+ if (mem[idx])
+ iounmap(base);
+ exit_release:
+ if (mem[idx])
+ release_mem_region(mem[idx], iosize);
+ else
+ release_region(port[idx], iosize);
+ exit:
+ return err;
+}
+
+static int sja1000_isa_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct sja1000_priv *priv = netdev_priv(dev);
+ int idx = pdev->id;
+
+ unregister_sja1000dev(dev);
+
+ if (mem[idx]) {
+ iounmap(priv->reg_base);
+ release_mem_region(mem[idx], SJA1000_IOSIZE);
+ } else {
+ if (priv->read_reg == sja1000_isa_port_read_reg_indirect)
+ release_region(port[idx], SJA1000_IOSIZE_INDIRECT);
+ else
+ release_region(port[idx], SJA1000_IOSIZE);
+ }
+ free_sja1000dev(dev);
+
+ return 0;
+}
+
+static struct platform_driver sja1000_isa_driver = {
+ .probe = sja1000_isa_probe,
+ .remove = sja1000_isa_remove,
+ .driver = {
+ .name = DRV_NAME,
+ },
+};
+
+static int __init sja1000_isa_init(void)
+{
+ int idx, err;
+
+ for (idx = 0; idx < MAXDEV; idx++) {
+ if ((port[idx] || mem[idx]) && irq[idx]) {
+ sja1000_isa_devs[idx] =
+ platform_device_alloc(DRV_NAME, idx);
+ if (!sja1000_isa_devs[idx]) {
+ err = -ENOMEM;
+ goto exit_free_devices;
+ }
+ err = platform_device_add(sja1000_isa_devs[idx]);
+ if (err) {
+ platform_device_put(sja1000_isa_devs[idx]);
+ goto exit_free_devices;
+ }
+ pr_debug("%s: platform device %d: port=%#lx, mem=%#lx, "
+ "irq=%d\n",
+ DRV_NAME, idx, port[idx], mem[idx], irq[idx]);
+ } else if (idx == 0 || port[idx] || mem[idx]) {
+ pr_err("%s: insufficient parameters supplied\n",
+ DRV_NAME);
+ err = -EINVAL;
+ goto exit_free_devices;
+ }
+ }
+
+ err = platform_driver_register(&sja1000_isa_driver);
+ if (err)
+ goto exit_free_devices;
+
+ pr_info("Legacy %s driver for max. %d devices registered\n",
+ DRV_NAME, MAXDEV);
+
+ return 0;
+
+exit_free_devices:
+ while (--idx >= 0) {
+ if (sja1000_isa_devs[idx])
+ platform_device_unregister(sja1000_isa_devs[idx]);
+ }
+
+ return err;
+}
+
+static void __exit sja1000_isa_exit(void)
+{
+ int idx;
+
+ platform_driver_unregister(&sja1000_isa_driver);
+ for (idx = 0; idx < MAXDEV; idx++) {
+ if (sja1000_isa_devs[idx])
+ platform_device_unregister(sja1000_isa_devs[idx]);
+ }
+}
+
+module_init(sja1000_isa_init);
+module_exit(sja1000_isa_exit);
diff --git a/drivers/net/can/sja1000/sja1000_platform.c b/drivers/net/can/sja1000/sja1000_platform.c
new file mode 100644
index 000000000..0552ed46a
--- /dev/null
+++ b/drivers/net/can/sja1000/sja1000_platform.c
@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2005 Sascha Hauer, Pengutronix
+ * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/can/dev.h>
+#include <linux/can/platform/sja1000.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME "sja1000_platform"
+#define SP_CAN_CLOCK (16000000 / 2)
+
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>");
+MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>");
+MODULE_DESCRIPTION("Socket-CAN driver for SJA1000 on the platform bus");
+MODULE_ALIAS("platform:" DRV_NAME);
+MODULE_LICENSE("GPL v2");
+
+static u8 sp_read_reg8(const struct sja1000_priv *priv, int reg)
+{
+ return ioread8(priv->reg_base + reg);
+}
+
+static void sp_write_reg8(const struct sja1000_priv *priv, int reg, u8 val)
+{
+ iowrite8(val, priv->reg_base + reg);
+}
+
+static u8 sp_read_reg16(const struct sja1000_priv *priv, int reg)
+{
+ return ioread8(priv->reg_base + reg * 2);
+}
+
+static void sp_write_reg16(const struct sja1000_priv *priv, int reg, u8 val)
+{
+ iowrite8(val, priv->reg_base + reg * 2);
+}
+
+static u8 sp_read_reg32(const struct sja1000_priv *priv, int reg)
+{
+ return ioread8(priv->reg_base + reg * 4);
+}
+
+static void sp_write_reg32(const struct sja1000_priv *priv, int reg, u8 val)
+{
+ iowrite8(val, priv->reg_base + reg * 4);
+}
+
+static void sp_populate(struct sja1000_priv *priv,
+ struct sja1000_platform_data *pdata,
+ unsigned long resource_mem_flags)
+{
+ /* The CAN clock frequency is half the oscillator clock frequency */
+ priv->can.clock.freq = pdata->osc_freq / 2;
+ priv->ocr = pdata->ocr;
+ priv->cdr = pdata->cdr;
+
+ switch (resource_mem_flags & IORESOURCE_MEM_TYPE_MASK) {
+ case IORESOURCE_MEM_32BIT:
+ priv->read_reg = sp_read_reg32;
+ priv->write_reg = sp_write_reg32;
+ break;
+ case IORESOURCE_MEM_16BIT:
+ priv->read_reg = sp_read_reg16;
+ priv->write_reg = sp_write_reg16;
+ break;
+ case IORESOURCE_MEM_8BIT:
+ default:
+ priv->read_reg = sp_read_reg8;
+ priv->write_reg = sp_write_reg8;
+ break;
+ }
+}
+
+static void sp_populate_of(struct sja1000_priv *priv, struct device_node *of)
+{
+ int err;
+ u32 prop;
+
+ err = of_property_read_u32(of, "reg-io-width", &prop);
+ if (err)
+ prop = 1; /* 8 bit is default */
+
+ switch (prop) {
+ case 4:
+ priv->read_reg = sp_read_reg32;
+ priv->write_reg = sp_write_reg32;
+ break;
+ case 2:
+ priv->read_reg = sp_read_reg16;
+ priv->write_reg = sp_write_reg16;
+ break;
+ case 1: /* fallthrough */
+ default:
+ priv->read_reg = sp_read_reg8;
+ priv->write_reg = sp_write_reg8;
+ }
+
+ err = of_property_read_u32(of, "nxp,external-clock-frequency", &prop);
+ if (!err)
+ priv->can.clock.freq = prop / 2;
+ else
+ priv->can.clock.freq = SP_CAN_CLOCK; /* default */
+
+ err = of_property_read_u32(of, "nxp,tx-output-mode", &prop);
+ if (!err)
+ priv->ocr |= prop & OCR_MODE_MASK;
+ else
+ priv->ocr |= OCR_MODE_NORMAL; /* default */
+
+ err = of_property_read_u32(of, "nxp,tx-output-config", &prop);
+ if (!err)
+ priv->ocr |= (prop << OCR_TX_SHIFT) & OCR_TX_MASK;
+ else
+ priv->ocr |= OCR_TX0_PULLDOWN; /* default */
+
+ err = of_property_read_u32(of, "nxp,clock-out-frequency", &prop);
+ if (!err && prop) {
+ u32 divider = priv->can.clock.freq * 2 / prop;
+
+ if (divider > 1)
+ priv->cdr |= divider / 2 - 1;
+ else
+ priv->cdr |= CDR_CLKOUT_MASK;
+ } else {
+ priv->cdr |= CDR_CLK_OFF; /* default */
+ }
+
+ if (!of_property_read_bool(of, "nxp,no-comparator-bypass"))
+ priv->cdr |= CDR_CBP; /* default */
+}
+
+static int sp_probe(struct platform_device *pdev)
+{
+ int err, irq = 0;
+ void __iomem *addr;
+ struct net_device *dev;
+ struct sja1000_priv *priv;
+ struct resource *res_mem, *res_irq = NULL;
+ struct sja1000_platform_data *pdata;
+ struct device_node *of = pdev->dev.of_node;
+
+ pdata = dev_get_platdata(&pdev->dev);
+ if (!pdata && !of) {
+ dev_err(&pdev->dev, "No platform data provided!\n");
+ return -ENODEV;
+ }
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ if (!devm_request_mem_region(&pdev->dev, res_mem->start,
+ resource_size(res_mem), DRV_NAME))
+ return -EBUSY;
+
+ addr = devm_ioremap_nocache(&pdev->dev, res_mem->start,
+ resource_size(res_mem));
+ if (!addr)
+ return -ENOMEM;
+
+ if (of)
+ irq = irq_of_parse_and_map(of, 0);
+ else
+ res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+ if (!irq && !res_irq)
+ return -ENODEV;
+
+ dev = alloc_sja1000dev(0);
+ if (!dev)
+ return -ENOMEM;
+ priv = netdev_priv(dev);
+
+ if (res_irq) {
+ irq = res_irq->start;
+ priv->irq_flags = res_irq->flags & IRQF_TRIGGER_MASK;
+ if (res_irq->flags & IORESOURCE_IRQ_SHAREABLE)
+ priv->irq_flags |= IRQF_SHARED;
+ } else {
+ priv->irq_flags = IRQF_SHARED;
+ }
+
+ dev->irq = irq;
+ priv->reg_base = addr;
+
+ if (of)
+ sp_populate_of(priv, of);
+ else
+ sp_populate(priv, pdata, res_mem->flags);
+
+ platform_set_drvdata(pdev, dev);
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ err = register_sja1000dev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "registering %s failed (err=%d)\n",
+ DRV_NAME, err);
+ goto exit_free;
+ }
+
+ dev_info(&pdev->dev, "%s device registered (reg_base=%p, irq=%d)\n",
+ DRV_NAME, priv->reg_base, dev->irq);
+ return 0;
+
+ exit_free:
+ free_sja1000dev(dev);
+ return err;
+}
+
+static int sp_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+
+ unregister_sja1000dev(dev);
+ free_sja1000dev(dev);
+
+ return 0;
+}
+
+static const struct of_device_id sp_of_table[] = {
+ {.compatible = "nxp,sja1000"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, sp_of_table);
+
+static struct platform_driver sp_driver = {
+ .probe = sp_probe,
+ .remove = sp_remove,
+ .driver = {
+ .name = DRV_NAME,
+ .of_match_table = sp_of_table,
+ },
+};
+
+module_platform_driver(sp_driver);
diff --git a/drivers/net/can/sja1000/tscan1.c b/drivers/net/can/sja1000/tscan1.c
new file mode 100644
index 000000000..76513dd78
--- /dev/null
+++ b/drivers/net/can/sja1000/tscan1.c
@@ -0,0 +1,216 @@
+/*
+ * tscan1.c: driver for Technologic Systems TS-CAN1 PC104 boards
+ *
+ * Copyright 2010 Andre B. Oliveira
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/*
+ * References:
+ * - Getting started with TS-CAN1, Technologic Systems, Jun 2009
+ * http://www.embeddedarm.com/documentation/ts-can1-manual.pdf
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/isa.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include "sja1000.h"
+
+MODULE_DESCRIPTION("Driver for Technologic Systems TS-CAN1 PC104 boards");
+MODULE_AUTHOR("Andre B. Oliveira <anbadeol@gmail.com>");
+MODULE_LICENSE("GPL");
+
+/* Maximum number of boards (one in each JP1:JP2 setting of IO address) */
+#define TSCAN1_MAXDEV 4
+
+/* PLD registers address offsets */
+#define TSCAN1_ID1 0
+#define TSCAN1_ID2 1
+#define TSCAN1_VERSION 2
+#define TSCAN1_LED 3
+#define TSCAN1_PAGE 4
+#define TSCAN1_MODE 5
+#define TSCAN1_JUMPERS 6
+
+/* PLD board identifier registers magic values */
+#define TSCAN1_ID1_VALUE 0xf6
+#define TSCAN1_ID2_VALUE 0xb9
+
+/* PLD mode register SJA1000 IO enable bit */
+#define TSCAN1_MODE_ENABLE 0x40
+
+/* PLD jumpers register bits */
+#define TSCAN1_JP4 0x10
+#define TSCAN1_JP5 0x20
+
+/* PLD IO base addresses start */
+#define TSCAN1_PLD_ADDRESS 0x150
+
+/* PLD register space size */
+#define TSCAN1_PLD_SIZE 8
+
+/* SJA1000 register space size */
+#define TSCAN1_SJA1000_SIZE 32
+
+/* SJA1000 crystal frequency (16MHz) */
+#define TSCAN1_SJA1000_XTAL 16000000
+
+/* SJA1000 IO base addresses */
+static const unsigned short tscan1_sja1000_addresses[] = {
+ 0x100, 0x120, 0x180, 0x1a0, 0x200, 0x240, 0x280, 0x320
+};
+
+/* Read SJA1000 register */
+static u8 tscan1_read(const struct sja1000_priv *priv, int reg)
+{
+ return inb((unsigned long)priv->reg_base + reg);
+}
+
+/* Write SJA1000 register */
+static void tscan1_write(const struct sja1000_priv *priv, int reg, u8 val)
+{
+ outb(val, (unsigned long)priv->reg_base + reg);
+}
+
+/* Probe for a TS-CAN1 board with JP2:JP1 jumper setting ID */
+static int tscan1_probe(struct device *dev, unsigned id)
+{
+ struct net_device *netdev;
+ struct sja1000_priv *priv;
+ unsigned long pld_base, sja1000_base;
+ int irq, i;
+
+ pld_base = TSCAN1_PLD_ADDRESS + id * TSCAN1_PLD_SIZE;
+ if (!request_region(pld_base, TSCAN1_PLD_SIZE, dev_name(dev)))
+ return -EBUSY;
+
+ if (inb(pld_base + TSCAN1_ID1) != TSCAN1_ID1_VALUE ||
+ inb(pld_base + TSCAN1_ID2) != TSCAN1_ID2_VALUE) {
+ release_region(pld_base, TSCAN1_PLD_SIZE);
+ return -ENODEV;
+ }
+
+ switch (inb(pld_base + TSCAN1_JUMPERS) & (TSCAN1_JP4 | TSCAN1_JP5)) {
+ case TSCAN1_JP4:
+ irq = 6;
+ break;
+ case TSCAN1_JP5:
+ irq = 7;
+ break;
+ case TSCAN1_JP4 | TSCAN1_JP5:
+ irq = 5;
+ break;
+ default:
+ dev_err(dev, "invalid JP4:JP5 setting (no IRQ)\n");
+ release_region(pld_base, TSCAN1_PLD_SIZE);
+ return -EINVAL;
+ }
+
+ netdev = alloc_sja1000dev(0);
+ if (!netdev) {
+ release_region(pld_base, TSCAN1_PLD_SIZE);
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(dev, netdev);
+ SET_NETDEV_DEV(netdev, dev);
+
+ netdev->base_addr = pld_base;
+ netdev->irq = irq;
+
+ priv = netdev_priv(netdev);
+ priv->read_reg = tscan1_read;
+ priv->write_reg = tscan1_write;
+ priv->can.clock.freq = TSCAN1_SJA1000_XTAL / 2;
+ priv->cdr = CDR_CBP | CDR_CLK_OFF;
+ priv->ocr = OCR_TX0_PUSHPULL;
+
+ /* Select the first SJA1000 IO address that is free and that works */
+ for (i = 0; i < ARRAY_SIZE(tscan1_sja1000_addresses); i++) {
+ sja1000_base = tscan1_sja1000_addresses[i];
+ if (!request_region(sja1000_base, TSCAN1_SJA1000_SIZE,
+ dev_name(dev)))
+ continue;
+
+ /* Set SJA1000 IO base address and enable it */
+ outb(TSCAN1_MODE_ENABLE | i, pld_base + TSCAN1_MODE);
+
+ priv->reg_base = (void __iomem *)sja1000_base;
+ if (!register_sja1000dev(netdev)) {
+ /* SJA1000 probe succeeded; turn LED off and return */
+ outb(0, pld_base + TSCAN1_LED);
+ netdev_info(netdev, "TS-CAN1 at 0x%lx 0x%lx irq %d\n",
+ pld_base, sja1000_base, irq);
+ return 0;
+ }
+
+ /* SJA1000 probe failed; release and try next address */
+ outb(0, pld_base + TSCAN1_MODE);
+ release_region(sja1000_base, TSCAN1_SJA1000_SIZE);
+ }
+
+ dev_err(dev, "failed to assign SJA1000 IO address\n");
+ dev_set_drvdata(dev, NULL);
+ free_sja1000dev(netdev);
+ release_region(pld_base, TSCAN1_PLD_SIZE);
+ return -ENXIO;
+}
+
+static int tscan1_remove(struct device *dev, unsigned id /*unused*/)
+{
+ struct net_device *netdev;
+ struct sja1000_priv *priv;
+ unsigned long pld_base, sja1000_base;
+
+ netdev = dev_get_drvdata(dev);
+ unregister_sja1000dev(netdev);
+ dev_set_drvdata(dev, NULL);
+
+ priv = netdev_priv(netdev);
+ pld_base = netdev->base_addr;
+ sja1000_base = (unsigned long)priv->reg_base;
+
+ outb(0, pld_base + TSCAN1_MODE); /* disable SJA1000 IO space */
+
+ release_region(sja1000_base, TSCAN1_SJA1000_SIZE);
+ release_region(pld_base, TSCAN1_PLD_SIZE);
+
+ free_sja1000dev(netdev);
+
+ return 0;
+}
+
+static struct isa_driver tscan1_isa_driver = {
+ .probe = tscan1_probe,
+ .remove = tscan1_remove,
+ .driver = {
+ .name = "tscan1",
+ },
+};
+
+static int __init tscan1_init(void)
+{
+ return isa_register_driver(&tscan1_isa_driver, TSCAN1_MAXDEV);
+}
+module_init(tscan1_init);
+
+static void __exit tscan1_exit(void)
+{
+ isa_unregister_driver(&tscan1_isa_driver);
+}
+module_exit(tscan1_exit);