summaryrefslogtreecommitdiff
path: root/drivers/net/dsa/mv88e6123_61_65.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/dsa/mv88e6123_61_65.c')
-rw-r--r--drivers/net/dsa/mv88e6123_61_65.c186
1 files changed, 13 insertions, 173 deletions
diff --git a/drivers/net/dsa/mv88e6123_61_65.c b/drivers/net/dsa/mv88e6123_61_65.c
index b4af6d5af..71a29a7ce 100644
--- a/drivers/net/dsa/mv88e6123_61_65.c
+++ b/drivers/net/dsa/mv88e6123_61_65.c
@@ -54,192 +54,40 @@ static char *mv88e6123_61_65_probe(struct device *host_dev, int sw_addr)
static int mv88e6123_61_65_setup_global(struct dsa_switch *ds)
{
+ u32 upstream_port = dsa_upstream_port(ds);
int ret;
- int i;
+ u32 reg;
+
+ ret = mv88e6xxx_setup_global(ds);
+ if (ret)
+ return ret;
/* Disable the PHY polling unit (since there won't be any
* external PHYs to poll), don't discard packets with
* excessive collisions, and mask all interrupt sources.
*/
- REG_WRITE(REG_GLOBAL, 0x04, 0x0000);
-
- /* Set the default address aging time to 5 minutes, and
- * enable address learn messages to be sent to all message
- * ports.
- */
- REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
-
- /* Configure the priority mapping registers. */
- ret = mv88e6xxx_config_prio(ds);
- if (ret < 0)
- return ret;
+ REG_WRITE(REG_GLOBAL, GLOBAL_CONTROL, 0x0000);
/* Configure the upstream port, and configure the upstream
* port as the port to which ingress and egress monitor frames
* are to be sent.
*/
- REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1110));
+ reg = upstream_port << GLOBAL_MONITOR_CONTROL_INGRESS_SHIFT |
+ upstream_port << GLOBAL_MONITOR_CONTROL_EGRESS_SHIFT |
+ upstream_port << GLOBAL_MONITOR_CONTROL_ARP_SHIFT;
+ REG_WRITE(REG_GLOBAL, GLOBAL_MONITOR_CONTROL, reg);
/* Disable remote management for now, and set the switch's
* DSA device number.
*/
- REG_WRITE(REG_GLOBAL, 0x1c, ds->index & 0x1f);
-
- /* Send all frames with destination addresses matching
- * 01:80:c2:00:00:2x to the CPU port.
- */
- REG_WRITE(REG_GLOBAL2, 0x02, 0xffff);
-
- /* Send all frames with destination addresses matching
- * 01:80:c2:00:00:0x to the CPU port.
- */
- REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
-
- /* Disable the loopback filter, disable flow control
- * messages, disable flood broadcast override, disable
- * removing of provider tags, disable ATU age violation
- * interrupts, disable tag flow control, force flow
- * control priority to the highest, and send all special
- * multicast frames to the CPU at the highest priority.
- */
- REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
-
- /* Program the DSA routing table. */
- for (i = 0; i < 32; i++) {
- int nexthop;
-
- nexthop = 0x1f;
- if (i != ds->index && i < ds->dst->pd->nr_chips)
- nexthop = ds->pd->rtable[i] & 0x1f;
-
- REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
- }
-
- /* Clear all trunk masks. */
- for (i = 0; i < 8; i++)
- REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0xff);
-
- /* Clear all trunk mappings. */
- for (i = 0; i < 16; i++)
- REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
-
- /* Disable ingress rate limiting by resetting all ingress
- * rate limit registers to their initial state.
- */
- for (i = 0; i < 6; i++)
- REG_WRITE(REG_GLOBAL2, 0x09, 0x9000 | (i << 8));
-
- /* Initialise cross-chip port VLAN table to reset defaults. */
- REG_WRITE(REG_GLOBAL2, 0x0b, 0x9000);
-
- /* Clear the priority override table. */
- for (i = 0; i < 16; i++)
- REG_WRITE(REG_GLOBAL2, 0x0f, 0x8000 | (i << 8));
-
- /* @@@ initialise AVB (22/23) watchdog (27) sdet (29) registers */
+ REG_WRITE(REG_GLOBAL, GLOBAL_CONTROL_2, ds->index & 0x1f);
return 0;
}
-static int mv88e6123_61_65_setup_port(struct dsa_switch *ds, int p)
-{
- int addr = REG_PORT(p);
- u16 val;
-
- /* MAC Forcing register: don't force link, speed, duplex
- * or flow control state to any particular values on physical
- * ports, but force the CPU port and all DSA ports to 1000 Mb/s
- * full duplex.
- */
- if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
- REG_WRITE(addr, 0x01, 0x003e);
- else
- REG_WRITE(addr, 0x01, 0x0003);
-
- /* Do not limit the period of time that this port can be
- * paused for by the remote end or the period of time that
- * this port can pause the remote end.
- */
- REG_WRITE(addr, 0x02, 0x0000);
-
- /* Port Control: disable Drop-on-Unlock, disable Drop-on-Lock,
- * disable Header mode, enable IGMP/MLD snooping, disable VLAN
- * tunneling, determine priority by looking at 802.1p and IP
- * priority fields (IP prio has precedence), and set STP state
- * to Forwarding.
- *
- * If this is the CPU link, use DSA or EDSA tagging depending
- * on which tagging mode was configured.
- *
- * If this is a link to another switch, use DSA tagging mode.
- *
- * If this is the upstream port for this switch, enable
- * forwarding of unknown unicasts and multicasts.
- */
- val = 0x0433;
- if (dsa_is_cpu_port(ds, p)) {
- if (ds->dst->tag_protocol == DSA_TAG_PROTO_EDSA)
- val |= 0x3300;
- else
- val |= 0x0100;
- }
- if (ds->dsa_port_mask & (1 << p))
- val |= 0x0100;
- if (p == dsa_upstream_port(ds))
- val |= 0x000c;
- REG_WRITE(addr, 0x04, val);
-
- /* Port Control 2: don't force a good FCS, set the maximum
- * frame size to 10240 bytes, don't let the switch add or
- * strip 802.1q tags, don't discard tagged or untagged frames
- * on this port, do a destination address lookup on all
- * received packets as usual, disable ARP mirroring and don't
- * send a copy of all transmitted/received frames on this port
- * to the CPU.
- */
- REG_WRITE(addr, 0x08, 0x2080);
-
- /* Egress rate control: disable egress rate control. */
- REG_WRITE(addr, 0x09, 0x0001);
-
- /* Egress rate control 2: disable egress rate control. */
- REG_WRITE(addr, 0x0a, 0x0000);
-
- /* Port Association Vector: when learning source addresses
- * of packets, add the address to the address database using
- * a port bitmap that has only the bit for this port set and
- * the other bits clear.
- */
- REG_WRITE(addr, 0x0b, 1 << p);
-
- /* Port ATU control: disable limiting the number of address
- * database entries that this port is allowed to use.
- */
- REG_WRITE(addr, 0x0c, 0x0000);
-
- /* Priority Override: disable DA, SA and VTU priority override. */
- REG_WRITE(addr, 0x0d, 0x0000);
-
- /* Port Ethertype: use the Ethertype DSA Ethertype value. */
- REG_WRITE(addr, 0x0f, ETH_P_EDSA);
-
- /* Tag Remap: use an identity 802.1p prio -> switch prio
- * mapping.
- */
- REG_WRITE(addr, 0x18, 0x3210);
-
- /* Tag Remap 2: use an identity 802.1p prio -> switch prio
- * mapping.
- */
- REG_WRITE(addr, 0x19, 0x7654);
-
- return mv88e6xxx_setup_port_common(ds, p);
-}
-
static int mv88e6123_61_65_setup(struct dsa_switch *ds)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
- int i;
int ret;
ret = mv88e6xxx_setup_common(ds);
@@ -262,19 +110,11 @@ static int mv88e6123_61_65_setup(struct dsa_switch *ds)
if (ret < 0)
return ret;
- /* @@@ initialise vtu and atu */
-
ret = mv88e6123_61_65_setup_global(ds);
if (ret < 0)
return ret;
- for (i = 0; i < ps->num_ports; i++) {
- ret = mv88e6123_61_65_setup_port(ds, i);
- if (ret < 0)
- return ret;
- }
-
- return 0;
+ return mv88e6xxx_setup_ports(ds);
}
struct dsa_switch_driver mv88e6123_61_65_switch_driver = {