summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/qcom
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pinctrl/qcom')
-rw-r--r--drivers/pinctrl/qcom/Kconfig20
-rw-r--r--drivers/pinctrl/qcom/Makefile3
-rw-r--r--drivers/pinctrl/qcom/pinctrl-msm.c20
-rw-r--r--drivers/pinctrl/qcom/pinctrl-qdf2xxx.c122
-rw-r--r--drivers/pinctrl/qcom/pinctrl-spmi-mpp.c376
-rw-r--r--drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c791
-rw-r--r--drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c882
7 files changed, 2015 insertions, 199 deletions
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 58f5632b2..383263a92 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -63,6 +63,14 @@ config PINCTRL_MSM8916
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block found on the Qualcomm 8916 platform.
+config PINCTRL_QDF2XXX
+ tristate "Qualcomm Technologies QDF2xxx pin controller driver"
+ depends on GPIOLIB && ACPI
+ select PINCTRL_MSM
+ help
+ This is the GPIO driver for the TLMM block found on the
+ Qualcomm Technologies QDF2xxx SOCs.
+
config PINCTRL_QCOM_SPMI_PMIC
tristate "Qualcomm SPMI PMIC pin controller driver"
depends on GPIOLIB && OF && SPMI
@@ -76,4 +84,16 @@ config PINCTRL_QCOM_SPMI_PMIC
which are using SPMI for communication with SoC. Example PMIC's
devices are pm8841, pm8941 and pma8084.
+config PINCTRL_QCOM_SSBI_PMIC
+ tristate "Qualcomm SSBI PMIC pin controller driver"
+ depends on GPIOLIB && OF
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+ Qualcomm GPIO and MPP blocks found in the Qualcomm PMIC's chips,
+ which are using SSBI for communication with SoC. Example PMIC's
+ devices are pm8058 and pm8921.
+
endif
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 3666c703c..13b190e72 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -7,5 +7,8 @@ obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
obj-$(CONFIG_PINCTRL_MSM8916) += pinctrl-msm8916.o
+obj-$(CONFIG_PINCTRL_QDF2XXX) += pinctrl-qdf2xxx.o
obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-gpio.o
obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-mpp.o
+obj-$(CONFIG_PINCTRL_QCOM_SSBI_PMIC) += pinctrl-ssbi-gpio.o
+obj-$(CONFIG_PINCTRL_QCOM_SSBI_PMIC) += pinctrl-ssbi-mpp.o
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index e457d5230..a0c7407c1 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -28,6 +28,7 @@
#include <linux/interrupt.h>
#include <linux/spinlock.h>
#include <linux/reboot.h>
+#include <linux/pm.h>
#include "../core.h"
#include "../pinconf.h"
@@ -733,9 +734,9 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
spin_unlock_irqrestore(&pctrl->lock, flags);
if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
- __irq_set_handler_locked(d->irq, handle_level_irq);
+ irq_set_handler_locked(d, handle_level_irq);
else if (type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
- __irq_set_handler_locked(d->irq, handle_edge_irq);
+ irq_set_handler_locked(d, handle_edge_irq);
return 0;
}
@@ -764,12 +765,12 @@ static struct irq_chip msm_gpio_irq_chip = {
.irq_set_wake = msm_gpio_irq_set_wake,
};
-static void msm_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void msm_gpio_irq_handler(struct irq_desc *desc)
{
struct gpio_chip *gc = irq_desc_get_handler_data(desc);
const struct msm_pingroup *g;
struct msm_pinctrl *pctrl = to_msm_pinctrl(gc);
- struct irq_chip *chip = irq_get_chip(irq);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
int irq_pin;
int handled = 0;
u32 val;
@@ -793,7 +794,7 @@ static void msm_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
/* No interrupts were flagged */
if (handled == 0)
- handle_bad_irq(irq, desc);
+ handle_bad_irq(desc);
chained_irq_exit(chip, desc);
}
@@ -855,6 +856,13 @@ static int msm_ps_hold_restart(struct notifier_block *nb, unsigned long action,
return NOTIFY_DONE;
}
+static struct msm_pinctrl *poweroff_pctrl;
+
+static void msm_ps_hold_poweroff(void)
+{
+ msm_ps_hold_restart(&poweroff_pctrl->restart_nb, 0, NULL);
+}
+
static void msm_pinctrl_setup_pm_reset(struct msm_pinctrl *pctrl)
{
int i;
@@ -867,6 +875,8 @@ static void msm_pinctrl_setup_pm_reset(struct msm_pinctrl *pctrl)
if (register_restart_handler(&pctrl->restart_nb))
dev_err(pctrl->dev,
"failed to setup restart handler.\n");
+ poweroff_pctrl = pctrl;
+ pm_power_off = msm_ps_hold_poweroff;
break;
}
}
diff --git a/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
new file mode 100644
index 000000000..e9ff3bc15
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-qdf2xxx.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * GPIO and pin control functions on this SOC are handled by the "TLMM"
+ * device. The driver which controls this device is pinctrl-msm.c. Each
+ * SOC with a TLMM is expected to create a client driver that registers
+ * with pinctrl-msm.c. This means that all TLMM drivers are pin control
+ * drivers.
+ *
+ * This pin control driver is intended to be used only an ACPI-enabled
+ * system. As such, UEFI will handle all pin control configuration, so
+ * this driver does not provide pin control functions. It is effectively
+ * a GPIO-only driver. The alternative is to duplicate the GPIO code of
+ * pinctrl-msm.c into another driver.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/acpi.h>
+
+#include "pinctrl-msm.h"
+
+static struct msm_pinctrl_soc_data qdf2xxx_pinctrl;
+
+static int qdf2xxx_pinctrl_probe(struct platform_device *pdev)
+{
+ struct pinctrl_pin_desc *pins;
+ struct msm_pingroup *groups;
+ unsigned int i;
+ u32 num_gpios;
+ int ret;
+
+ /* Query the number of GPIOs from ACPI */
+ ret = device_property_read_u32(&pdev->dev, "num-gpios", &num_gpios);
+ if (ret < 0)
+ return ret;
+
+ if (!num_gpios) {
+ dev_warn(&pdev->dev, "missing num-gpios property\n");
+ return -ENODEV;
+ }
+
+ pins = devm_kcalloc(&pdev->dev, num_gpios,
+ sizeof(struct pinctrl_pin_desc), GFP_KERNEL);
+ groups = devm_kcalloc(&pdev->dev, num_gpios,
+ sizeof(struct msm_pingroup), GFP_KERNEL);
+
+ for (i = 0; i < num_gpios; i++) {
+ pins[i].number = i;
+
+ groups[i].npins = 1,
+ groups[i].pins = &pins[i].number;
+ groups[i].ctl_reg = 0x10000 * i;
+ groups[i].io_reg = 0x04 + 0x10000 * i;
+ groups[i].intr_cfg_reg = 0x08 + 0x10000 * i;
+ groups[i].intr_status_reg = 0x0c + 0x10000 * i;
+ groups[i].intr_target_reg = 0x08 + 0x10000 * i;
+
+ groups[i].mux_bit = 2;
+ groups[i].pull_bit = 0;
+ groups[i].drv_bit = 6;
+ groups[i].oe_bit = 9;
+ groups[i].in_bit = 0;
+ groups[i].out_bit = 1;
+ groups[i].intr_enable_bit = 0;
+ groups[i].intr_status_bit = 0;
+ groups[i].intr_target_bit = 5;
+ groups[i].intr_target_kpss_val = 1;
+ groups[i].intr_raw_status_bit = 4;
+ groups[i].intr_polarity_bit = 1;
+ groups[i].intr_detection_bit = 2;
+ groups[i].intr_detection_width = 2;
+ }
+
+ qdf2xxx_pinctrl.pins = pins;
+ qdf2xxx_pinctrl.groups = groups;
+ qdf2xxx_pinctrl.npins = num_gpios;
+ qdf2xxx_pinctrl.ngroups = num_gpios;
+ qdf2xxx_pinctrl.ngpios = num_gpios;
+
+ return msm_pinctrl_probe(pdev, &qdf2xxx_pinctrl);
+}
+
+static const struct acpi_device_id qdf2xxx_acpi_ids[] = {
+ {"QCOM8001"},
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, qdf2xxx_acpi_ids);
+
+static struct platform_driver qdf2xxx_pinctrl_driver = {
+ .driver = {
+ .name = "qdf2xxx-pinctrl",
+ .acpi_match_table = ACPI_PTR(qdf2xxx_acpi_ids),
+ },
+ .probe = qdf2xxx_pinctrl_probe,
+ .remove = msm_pinctrl_remove,
+};
+
+static int __init qdf2xxx_pinctrl_init(void)
+{
+ return platform_driver_register(&qdf2xxx_pinctrl_driver);
+}
+arch_initcall(qdf2xxx_pinctrl_init);
+
+static void __exit qdf2xxx_pinctrl_exit(void)
+{
+ platform_driver_unregister(&qdf2xxx_pinctrl_driver);
+}
+module_exit(qdf2xxx_pinctrl_exit);
+
+MODULE_DESCRIPTION("Qualcomm Technologies QDF2xxx pin control driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
index 3121de9b6..e3be3ce2c 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
@@ -61,7 +61,9 @@
#define PMIC_MPP_REG_DIG_PULL_CTL 0x42
#define PMIC_MPP_REG_DIG_IN_CTL 0x43
#define PMIC_MPP_REG_EN_CTL 0x46
+#define PMIC_MPP_REG_AOUT_CTL 0x48
#define PMIC_MPP_REG_AIN_CTL 0x4a
+#define PMIC_MPP_REG_SINK_CTL 0x4c
/* PMIC_MPP_REG_MODE_CTL */
#define PMIC_MPP_REG_MODE_VALUE_MASK 0x1
@@ -85,11 +87,25 @@
#define PMIC_MPP_REG_AIN_ROUTE_SHIFT 0
#define PMIC_MPP_REG_AIN_ROUTE_MASK 0x7
+#define PMIC_MPP_MODE_DIGITAL_INPUT 0
+#define PMIC_MPP_MODE_DIGITAL_OUTPUT 1
+#define PMIC_MPP_MODE_DIGITAL_BIDIR 2
+#define PMIC_MPP_MODE_ANALOG_BIDIR 3
+#define PMIC_MPP_MODE_ANALOG_INPUT 4
+#define PMIC_MPP_MODE_ANALOG_OUTPUT 5
+#define PMIC_MPP_MODE_CURRENT_SINK 6
+
+#define PMIC_MPP_SELECTOR_NORMAL 0
+#define PMIC_MPP_SELECTOR_PAIRED 1
+#define PMIC_MPP_SELECTOR_DTEST_FIRST 4
+
#define PMIC_MPP_PHYSICAL_OFFSET 1
/* Qualcomm specific pin configurations */
#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1)
-#define PMIC_MPP_CONF_ANALOG_MODE (PIN_CONFIG_END + 2)
+#define PMIC_MPP_CONF_ANALOG_LEVEL (PIN_CONFIG_END + 2)
+#define PMIC_MPP_CONF_DTEST_SELECTOR (PIN_CONFIG_END + 3)
+#define PMIC_MPP_CONF_PAIRED (PIN_CONFIG_END + 4)
/**
* struct pmic_mpp_pad - keep current MPP settings
@@ -99,13 +115,15 @@
* @out_value: Cached pin output value.
* @output_enabled: Set to true if MPP output logic is enabled.
* @input_enabled: Set to true if MPP input buffer logic is enabled.
- * @analog_mode: Set to true when MPP should operate in Analog Input, Analog
- * Output or Bidirectional Analog mode.
+ * @paired: Pin operates in paired mode
* @num_sources: Number of power-sources supported by this MPP.
* @power_source: Current power-source used.
* @amux_input: Set the source for analog input.
+ * @aout_level: Analog output level
* @pullup: Pullup resistor value. Valid in Bidirectional mode only.
* @function: See pmic_mpp_functions[].
+ * @drive_strength: Amount of current in sink mode
+ * @dtest: DTEST route selector
*/
struct pmic_mpp_pad {
u16 base;
@@ -114,12 +132,15 @@ struct pmic_mpp_pad {
bool out_value;
bool output_enabled;
bool input_enabled;
- bool analog_mode;
+ bool paired;
unsigned int num_sources;
unsigned int power_source;
unsigned int amux_input;
+ unsigned int aout_level;
unsigned int pullup;
unsigned int function;
+ unsigned int drive_strength;
+ unsigned int dtest;
};
struct pmic_mpp_state {
@@ -129,25 +150,32 @@ struct pmic_mpp_state {
struct gpio_chip chip;
};
-struct pmic_mpp_bindings {
- const char *property;
- unsigned param;
+static const struct pinconf_generic_params pmic_mpp_bindings[] = {
+ {"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0},
+ {"qcom,analog-level", PMIC_MPP_CONF_ANALOG_LEVEL, 0},
+ {"qcom,dtest", PMIC_MPP_CONF_DTEST_SELECTOR, 0},
+ {"qcom,paired", PMIC_MPP_CONF_PAIRED, 0},
};
-static struct pmic_mpp_bindings pmic_mpp_bindings[] = {
- {"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE},
- {"qcom,analog-mode", PMIC_MPP_CONF_ANALOG_MODE},
+#ifdef CONFIG_DEBUG_FS
+static const struct pin_config_item pmic_conf_items[] = {
+ PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true),
+ PCONFDUMP(PMIC_MPP_CONF_ANALOG_LEVEL, "analog level", NULL, true),
+ PCONFDUMP(PMIC_MPP_CONF_DTEST_SELECTOR, "dtest", NULL, true),
+ PCONFDUMP(PMIC_MPP_CONF_PAIRED, "paired", NULL, false),
};
+#endif
static const char *const pmic_mpp_groups[] = {
"mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
};
+#define PMIC_MPP_DIGITAL 0
+#define PMIC_MPP_ANALOG 1
+#define PMIC_MPP_SINK 2
+
static const char *const pmic_mpp_functions[] = {
- PMIC_MPP_FUNC_NORMAL, PMIC_MPP_FUNC_PAIRED,
- "reserved1", "reserved2",
- PMIC_MPP_FUNC_DTEST1, PMIC_MPP_FUNC_DTEST2,
- PMIC_MPP_FUNC_DTEST3, PMIC_MPP_FUNC_DTEST4,
+ "digital", "analog", "sink"
};
static inline struct pmic_mpp_state *to_mpp_state(struct gpio_chip *chip)
@@ -204,118 +232,11 @@ static int pmic_mpp_get_group_pins(struct pinctrl_dev *pctldev,
return 0;
}
-static int pmic_mpp_parse_dt_config(struct device_node *np,
- struct pinctrl_dev *pctldev,
- unsigned long **configs,
- unsigned int *nconfs)
-{
- struct pmic_mpp_bindings *par;
- unsigned long cfg;
- int ret, i;
- u32 val;
-
- for (i = 0; i < ARRAY_SIZE(pmic_mpp_bindings); i++) {
- par = &pmic_mpp_bindings[i];
- ret = of_property_read_u32(np, par->property, &val);
-
- /* property not found */
- if (ret == -EINVAL)
- continue;
-
- /* use zero as default value, when no value is specified */
- if (ret)
- val = 0;
-
- dev_dbg(pctldev->dev, "found %s with value %u\n",
- par->property, val);
-
- cfg = pinconf_to_config_packed(par->param, val);
-
- ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-
-static int pmic_mpp_dt_subnode_to_map(struct pinctrl_dev *pctldev,
- struct device_node *np,
- struct pinctrl_map **map,
- unsigned *reserv, unsigned *nmaps,
- enum pinctrl_map_type type)
-{
- unsigned long *configs = NULL;
- unsigned nconfs = 0;
- struct property *prop;
- const char *group;
- int ret;
-
- ret = pmic_mpp_parse_dt_config(np, pctldev, &configs, &nconfs);
- if (ret < 0)
- return ret;
-
- if (!nconfs)
- return 0;
-
- ret = of_property_count_strings(np, "pins");
- if (ret < 0)
- goto exit;
-
- ret = pinctrl_utils_reserve_map(pctldev, map, reserv, nmaps, ret);
- if (ret < 0)
- goto exit;
-
- of_property_for_each_string(np, "pins", prop, group) {
- ret = pinctrl_utils_add_map_configs(pctldev, map,
- reserv, nmaps, group,
- configs, nconfs, type);
- if (ret < 0)
- break;
- }
-exit:
- kfree(configs);
- return ret;
-}
-
-static int pmic_mpp_dt_node_to_map(struct pinctrl_dev *pctldev,
- struct device_node *np_config,
- struct pinctrl_map **map, unsigned *nmaps)
-{
- struct device_node *np;
- enum pinctrl_map_type type;
- unsigned reserv;
- int ret;
-
- ret = 0;
- *map = NULL;
- *nmaps = 0;
- reserv = 0;
- type = PIN_MAP_TYPE_CONFIGS_GROUP;
-
- for_each_child_of_node(np_config, np) {
- ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
- &reserv, nmaps, type);
- if (ret)
- break;
-
- ret = pmic_mpp_dt_subnode_to_map(pctldev, np, map, &reserv,
- nmaps, type);
- if (ret)
- break;
- }
-
- if (ret < 0)
- pinctrl_utils_dt_free_map(pctldev, *map, *nmaps);
-
- return ret;
-}
-
static const struct pinctrl_ops pmic_mpp_pinctrl_ops = {
.get_groups_count = pmic_mpp_get_groups_count,
.get_group_name = pmic_mpp_get_group_name,
.get_group_pins = pmic_mpp_get_group_pins,
- .dt_node_to_map = pmic_mpp_dt_node_to_map,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
.dt_free_map = pinctrl_utils_dt_free_map,
};
@@ -340,6 +261,53 @@ static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev,
return 0;
}
+static int pmic_mpp_write_mode_ctl(struct pmic_mpp_state *state,
+ struct pmic_mpp_pad *pad)
+{
+ unsigned int mode;
+ unsigned int sel;
+ unsigned int val;
+ unsigned int en;
+
+ switch (pad->function) {
+ case PMIC_MPP_ANALOG:
+ if (pad->input_enabled && pad->output_enabled)
+ mode = PMIC_MPP_MODE_ANALOG_BIDIR;
+ else if (pad->input_enabled)
+ mode = PMIC_MPP_MODE_ANALOG_INPUT;
+ else
+ mode = PMIC_MPP_MODE_ANALOG_OUTPUT;
+ break;
+ case PMIC_MPP_DIGITAL:
+ if (pad->input_enabled && pad->output_enabled)
+ mode = PMIC_MPP_MODE_DIGITAL_BIDIR;
+ else if (pad->input_enabled)
+ mode = PMIC_MPP_MODE_DIGITAL_INPUT;
+ else
+ mode = PMIC_MPP_MODE_DIGITAL_OUTPUT;
+ break;
+ case PMIC_MPP_SINK:
+ default:
+ mode = PMIC_MPP_MODE_CURRENT_SINK;
+ break;
+ }
+
+ if (pad->dtest)
+ sel = PMIC_MPP_SELECTOR_DTEST_FIRST + pad->dtest - 1;
+ else if (pad->paired)
+ sel = PMIC_MPP_SELECTOR_PAIRED;
+ else
+ sel = PMIC_MPP_SELECTOR_NORMAL;
+
+ en = !!pad->out_value;
+
+ val = mode << PMIC_MPP_REG_MODE_DIR_SHIFT |
+ sel << PMIC_MPP_REG_MODE_FUNCTION_SHIFT |
+ en;
+
+ return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
+}
+
static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
unsigned pin)
{
@@ -352,31 +320,7 @@ static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
pad->function = function;
- if (!pad->analog_mode) {
- val = 0; /* just digital input */
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 2; /* digital input and output */
- else
- val = 1; /* just digital output */
- }
- } else {
- val = 4; /* just analog input */
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 3; /* analog input and output */
- else
- val = 5; /* just analog output */
- }
- }
-
- val = val << PMIC_MPP_REG_MODE_DIR_SHIFT;
- val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
- val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
-
- ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
- if (ret < 0)
- return ret;
+ ret = pmic_mpp_write_mode_ctl(state, pad);
val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
@@ -433,11 +377,20 @@ static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
case PIN_CONFIG_OUTPUT:
arg = pad->out_value;
break;
+ case PMIC_MPP_CONF_DTEST_SELECTOR:
+ arg = pad->dtest;
+ break;
case PMIC_MPP_CONF_AMUX_ROUTE:
arg = pad->amux_input;
break;
- case PMIC_MPP_CONF_ANALOG_MODE:
- arg = pad->analog_mode;
+ case PMIC_MPP_CONF_PAIRED:
+ arg = pad->paired;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ arg = pad->drive_strength;
+ break;
+ case PMIC_MPP_CONF_ANALOG_LEVEL:
+ arg = pad->aout_level;
break;
default:
return -EINVAL;
@@ -459,6 +412,9 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
pad = pctldev->desc->pins[pin].drv_data;
+ /* Make it possible to enable the pin, by not setting high impedance */
+ pad->is_enabled = true;
+
for (i = 0; i < nconfs; i++) {
param = pinconf_to_config_param(configs[i]);
arg = pinconf_to_config_argument(configs[i]);
@@ -497,13 +453,22 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
pad->output_enabled = true;
pad->out_value = arg;
break;
+ case PMIC_MPP_CONF_DTEST_SELECTOR:
+ pad->dtest = arg;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ arg = pad->drive_strength;
+ break;
case PMIC_MPP_CONF_AMUX_ROUTE:
if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4)
return -EINVAL;
pad->amux_input = arg;
break;
- case PMIC_MPP_CONF_ANALOG_MODE:
- pad->analog_mode = true;
+ case PMIC_MPP_CONF_ANALOG_LEVEL:
+ pad->aout_level = arg;
+ break;
+ case PMIC_MPP_CONF_PAIRED:
+ pad->paired = !!arg;
break;
default:
return -EINVAL;
@@ -528,29 +493,17 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
if (ret < 0)
return ret;
- if (!pad->analog_mode) {
- val = 0; /* just digital input */
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 2; /* digital input and output */
- else
- val = 1; /* just digital output */
- }
- } else {
- val = 4; /* just analog input */
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 3; /* analog input and output */
- else
- val = 5; /* just analog output */
- }
- }
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AOUT_CTL, pad->aout_level);
+ if (ret < 0)
+ return ret;
+
+ ret = pmic_mpp_write_mode_ctl(state, pad);
+ if (ret < 0)
+ return ret;
- val = val << PMIC_MPP_REG_MODE_DIR_SHIFT;
- val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
- val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
+ val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
- return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
+ return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
}
static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
@@ -558,20 +511,17 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
{
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
struct pmic_mpp_pad *pad;
- int ret, val;
+ int ret;
static const char *const biases[] = {
"0.6kOhm", "10kOhm", "30kOhm", "Disabled"
};
-
pad = pctldev->desc->pins[pin].drv_data;
seq_printf(s, " mpp%-2d:", pin + PMIC_MPP_PHYSICAL_OFFSET);
- val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
-
- if (val < 0 || !(val >> PMIC_MPP_REG_MASTER_EN_SHIFT)) {
+ if (!pad->is_enabled) {
seq_puts(s, " ---");
} else {
@@ -585,15 +535,20 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
}
seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
- seq_printf(s, " %-4s", pad->analog_mode ? "ana" : "dig");
seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
seq_printf(s, " vin-%d", pad->power_source);
+ seq_printf(s, " %d", pad->aout_level);
seq_printf(s, " %-8s", biases[pad->pullup]);
seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
+ if (pad->dtest)
+ seq_printf(s, " dtest%d", pad->dtest);
+ if (pad->paired)
+ seq_puts(s, " paired");
}
}
static const struct pinconf_ops pmic_mpp_pinconf_ops = {
+ .is_generic = true,
.pin_config_group_get = pmic_mpp_config_get,
.pin_config_group_set = pmic_mpp_config_set,
.pin_config_group_dbg_show = pmic_mpp_config_dbg_show,
@@ -709,6 +664,7 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
struct pmic_mpp_pad *pad)
{
int type, subtype, val, dir;
+ unsigned int sel;
type = pmic_mpp_read(state, pad, PMIC_MPP_REG_TYPE);
if (type < 0)
@@ -751,43 +707,53 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
dir &= PMIC_MPP_REG_MODE_DIR_MASK;
switch (dir) {
- case 0:
+ case PMIC_MPP_MODE_DIGITAL_INPUT:
pad->input_enabled = true;
pad->output_enabled = false;
- pad->analog_mode = false;
+ pad->function = PMIC_MPP_DIGITAL;
break;
- case 1:
+ case PMIC_MPP_MODE_DIGITAL_OUTPUT:
pad->input_enabled = false;
pad->output_enabled = true;
- pad->analog_mode = false;
+ pad->function = PMIC_MPP_DIGITAL;
break;
- case 2:
+ case PMIC_MPP_MODE_DIGITAL_BIDIR:
pad->input_enabled = true;
pad->output_enabled = true;
- pad->analog_mode = false;
+ pad->function = PMIC_MPP_DIGITAL;
break;
- case 3:
+ case PMIC_MPP_MODE_ANALOG_BIDIR:
pad->input_enabled = true;
pad->output_enabled = true;
- pad->analog_mode = true;
+ pad->function = PMIC_MPP_ANALOG;
break;
- case 4:
+ case PMIC_MPP_MODE_ANALOG_INPUT:
pad->input_enabled = true;
pad->output_enabled = false;
- pad->analog_mode = true;
+ pad->function = PMIC_MPP_ANALOG;
break;
- case 5:
+ case PMIC_MPP_MODE_ANALOG_OUTPUT:
pad->input_enabled = false;
pad->output_enabled = true;
- pad->analog_mode = true;
+ pad->function = PMIC_MPP_ANALOG;
+ break;
+ case PMIC_MPP_MODE_CURRENT_SINK:
+ pad->input_enabled = false;
+ pad->output_enabled = true;
+ pad->function = PMIC_MPP_SINK;
break;
default:
dev_err(state->dev, "unknown MPP direction\n");
return -ENODEV;
}
- pad->function = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
- pad->function &= PMIC_MPP_REG_MODE_FUNCTION_MASK;
+ sel = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
+ sel &= PMIC_MPP_REG_MODE_FUNCTION_MASK;
+
+ if (sel >= PMIC_MPP_SELECTOR_DTEST_FIRST)
+ pad->dtest = sel + 1;
+ else if (sel == PMIC_MPP_SELECTOR_PAIRED)
+ pad->paired = true;
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_VIN_CTL);
if (val < 0)
@@ -810,8 +776,24 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT;
pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK;
- /* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */
- pad->is_enabled = true;
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_SINK_CTL);
+ if (val < 0)
+ return val;
+
+ pad->drive_strength = val;
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AOUT_CTL);
+ if (val < 0)
+ return val;
+
+ pad->aout_level = val;
+
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
+ if (val < 0)
+ return val;
+
+ pad->is_enabled = !!val;
+
return 0;
}
@@ -866,6 +848,12 @@ static int pmic_mpp_probe(struct platform_device *pdev)
pctrldesc->pins = pindesc;
pctrldesc->npins = npins;
+ pctrldesc->num_custom_params = ARRAY_SIZE(pmic_mpp_bindings);
+ pctrldesc->custom_params = pmic_mpp_bindings;
+#ifdef CONFIG_DEBUG_FS
+ pctrldesc->custom_conf_items = pmic_conf_items;
+#endif
+
for (i = 0; i < npins; i++, pindesc++) {
pad = &pads[i];
pindesc->drv_data = pad;
diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
new file mode 100644
index 000000000..d809c9eaa
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
@@ -0,0 +1,791 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/of_device.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+/* mode */
+#define PM8XXX_GPIO_MODE_ENABLED BIT(0)
+#define PM8XXX_GPIO_MODE_INPUT 0
+#define PM8XXX_GPIO_MODE_OUTPUT 2
+
+/* output buffer */
+#define PM8XXX_GPIO_PUSH_PULL 0
+#define PM8XXX_GPIO_OPEN_DRAIN 1
+
+/* bias */
+#define PM8XXX_GPIO_BIAS_PU_30 0
+#define PM8XXX_GPIO_BIAS_PU_1P5 1
+#define PM8XXX_GPIO_BIAS_PU_31P5 2
+#define PM8XXX_GPIO_BIAS_PU_1P5_30 3
+#define PM8XXX_GPIO_BIAS_PD 4
+#define PM8XXX_GPIO_BIAS_NP 5
+
+/* GPIO registers */
+#define SSBI_REG_ADDR_GPIO_BASE 0x150
+#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n)
+
+#define PM8XXX_BANK_WRITE BIT(7)
+
+#define PM8XXX_MAX_GPIOS 44
+
+/* custom pinconf parameters */
+#define PM8XXX_QCOM_DRIVE_STRENGH (PIN_CONFIG_END + 1)
+#define PM8XXX_QCOM_PULL_UP_STRENGTH (PIN_CONFIG_END + 2)
+
+/**
+ * struct pm8xxx_pin_data - dynamic configuration for a pin
+ * @reg: address of the control register
+ * @irq: IRQ from the PMIC interrupt controller
+ * @power_source: logical selected voltage source, mapping in static data
+ * is used translate to register values
+ * @mode: operating mode for the pin (input/output)
+ * @open_drain: output buffer configured as open-drain (vs push-pull)
+ * @output_value: configured output value
+ * @bias: register view of configured bias
+ * @pull_up_strength: placeholder for selected pull up strength
+ * only used to configure bias when pull up is selected
+ * @output_strength: selector of output-strength
+ * @disable: pin disabled / configured as tristate
+ * @function: pinmux selector
+ * @inverted: pin logic is inverted
+ */
+struct pm8xxx_pin_data {
+ unsigned reg;
+ int irq;
+ u8 power_source;
+ u8 mode;
+ bool open_drain;
+ bool output_value;
+ u8 bias;
+ u8 pull_up_strength;
+ u8 output_strength;
+ bool disable;
+ u8 function;
+ bool inverted;
+};
+
+struct pm8xxx_gpio {
+ struct device *dev;
+ struct regmap *regmap;
+ struct pinctrl_dev *pctrl;
+ struct gpio_chip chip;
+
+ struct pinctrl_desc desc;
+ unsigned npins;
+};
+
+static const struct pinconf_generic_params pm8xxx_gpio_bindings[] = {
+ {"qcom,drive-strength", PM8XXX_QCOM_DRIVE_STRENGH, 0},
+ {"qcom,pull-up-strength", PM8XXX_QCOM_PULL_UP_STRENGTH, 0},
+};
+
+#ifdef CONFIG_DEBUG_FS
+static const struct pin_config_item pm8xxx_conf_items[ARRAY_SIZE(pm8xxx_gpio_bindings)] = {
+ PCONFDUMP(PM8XXX_QCOM_DRIVE_STRENGH, "drive-strength", NULL, true),
+ PCONFDUMP(PM8XXX_QCOM_PULL_UP_STRENGTH, "pull up strength", NULL, true),
+};
+#endif
+
+static const char * const pm8xxx_groups[PM8XXX_MAX_GPIOS] = {
+ "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+ "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+ "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+ "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+ "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", "gpio43",
+ "gpio44",
+};
+
+static const char * const pm8xxx_gpio_functions[] = {
+ PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
+ PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
+ PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
+ PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+};
+
+static int pm8xxx_read_bank(struct pm8xxx_gpio *pctrl,
+ struct pm8xxx_pin_data *pin, int bank)
+{
+ unsigned int val = bank << 4;
+ int ret;
+
+ ret = regmap_write(pctrl->regmap, pin->reg, val);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to select bank %d\n", bank);
+ return ret;
+ }
+
+ ret = regmap_read(pctrl->regmap, pin->reg, &val);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to read register %d\n", bank);
+ return ret;
+ }
+
+ return val;
+}
+
+static int pm8xxx_write_bank(struct pm8xxx_gpio *pctrl,
+ struct pm8xxx_pin_data *pin,
+ int bank,
+ u8 val)
+{
+ int ret;
+
+ val |= PM8XXX_BANK_WRITE;
+ val |= bank << 4;
+
+ ret = regmap_write(pctrl->regmap, pin->reg, val);
+ if (ret)
+ dev_err(pctrl->dev, "failed to write register\n");
+
+ return ret;
+}
+
+static int pm8xxx_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->npins;
+}
+
+static const char *pm8xxx_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned group)
+{
+ return pm8xxx_groups[group];
+}
+
+
+static int pm8xxx_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned group,
+ const unsigned **pins,
+ unsigned *num_pins)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = &pctrl->desc.pins[group].number;
+ *num_pins = 1;
+
+ return 0;
+}
+
+static const struct pinctrl_ops pm8xxx_pinctrl_ops = {
+ .get_groups_count = pm8xxx_get_groups_count,
+ .get_group_name = pm8xxx_get_group_name,
+ .get_group_pins = pm8xxx_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int pm8xxx_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(pm8xxx_gpio_functions);
+}
+
+static const char *pm8xxx_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return pm8xxx_gpio_functions[function];
+}
+
+static int pm8xxx_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = pm8xxx_groups;
+ *num_groups = pctrl->npins;
+ return 0;
+}
+
+static int pm8xxx_pinmux_set_mux(struct pinctrl_dev *pctldev,
+ unsigned function,
+ unsigned group)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[group].drv_data;
+ u8 val;
+
+ pin->function = function;
+ val = pin->function << 1;
+
+ pm8xxx_write_bank(pctrl, pin, 4, val);
+
+ return 0;
+}
+
+static const struct pinmux_ops pm8xxx_pinmux_ops = {
+ .get_functions_count = pm8xxx_get_functions_count,
+ .get_function_name = pm8xxx_get_function_name,
+ .get_function_groups = pm8xxx_get_function_groups,
+ .set_mux = pm8xxx_pinmux_set_mux,
+};
+
+static int pm8xxx_pin_config_get(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *config)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ unsigned param = pinconf_to_config_param(*config);
+ unsigned arg;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = pin->bias == PM8XXX_GPIO_BIAS_NP;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ arg = pin->bias == PM8XXX_GPIO_BIAS_PD;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ arg = pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30;
+ break;
+ case PM8XXX_QCOM_PULL_UP_STRENGTH:
+ arg = pin->pull_up_strength;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ arg = pin->disable;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ arg = pin->mode == PM8XXX_GPIO_MODE_INPUT;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ if (pin->mode & PM8XXX_GPIO_MODE_OUTPUT)
+ arg = pin->output_value;
+ else
+ arg = 0;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = pin->power_source;
+ break;
+ case PM8XXX_QCOM_DRIVE_STRENGH:
+ arg = pin->output_strength;
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ arg = !pin->open_drain;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ arg = pin->open_drain;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *configs,
+ unsigned num_configs)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ unsigned param;
+ unsigned arg;
+ unsigned i;
+ u8 banks = 0;
+ u8 val;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ pin->bias = PM8XXX_GPIO_BIAS_NP;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ pin->bias = PM8XXX_GPIO_BIAS_PD;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PM8XXX_QCOM_PULL_UP_STRENGTH:
+ if (arg > PM8XXX_GPIO_BIAS_PU_1P5_30) {
+ dev_err(pctrl->dev, "invalid pull-up strength\n");
+ return -EINVAL;
+ }
+ pin->pull_up_strength = arg;
+ /* FALLTHROUGH */
+ case PIN_CONFIG_BIAS_PULL_UP:
+ pin->bias = pin->pull_up_strength;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ pin->disable = 1;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ pin->mode = PM8XXX_GPIO_MODE_INPUT;
+ banks |= BIT(0) | BIT(1);
+ break;
+ case PIN_CONFIG_OUTPUT:
+ pin->mode = PM8XXX_GPIO_MODE_OUTPUT;
+ pin->output_value = !!arg;
+ banks |= BIT(0) | BIT(1);
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ pin->power_source = arg;
+ banks |= BIT(0);
+ break;
+ case PM8XXX_QCOM_DRIVE_STRENGH:
+ if (arg > PMIC_GPIO_STRENGTH_LOW) {
+ dev_err(pctrl->dev, "invalid drive strength\n");
+ return -EINVAL;
+ }
+ pin->output_strength = arg;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ pin->open_drain = 0;
+ banks |= BIT(1);
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ pin->open_drain = 1;
+ banks |= BIT(1);
+ break;
+ default:
+ dev_err(pctrl->dev,
+ "unsupported config parameter: %x\n",
+ param);
+ return -EINVAL;
+ }
+ }
+
+ if (banks & BIT(0)) {
+ val = pin->power_source << 1;
+ val |= PM8XXX_GPIO_MODE_ENABLED;
+ pm8xxx_write_bank(pctrl, pin, 0, val);
+ }
+
+ if (banks & BIT(1)) {
+ val = pin->mode << 2;
+ val |= pin->open_drain << 1;
+ val |= pin->output_value;
+ pm8xxx_write_bank(pctrl, pin, 1, val);
+ }
+
+ if (banks & BIT(2)) {
+ val = pin->bias << 1;
+ pm8xxx_write_bank(pctrl, pin, 2, val);
+ }
+
+ if (banks & BIT(3)) {
+ val = pin->output_strength << 2;
+ val |= pin->disable;
+ pm8xxx_write_bank(pctrl, pin, 3, val);
+ }
+
+ if (banks & BIT(4)) {
+ val = pin->function << 1;
+ pm8xxx_write_bank(pctrl, pin, 4, val);
+ }
+
+ if (banks & BIT(5)) {
+ val = 0;
+ if (!pin->inverted)
+ val |= BIT(3);
+ pm8xxx_write_bank(pctrl, pin, 5, val);
+ }
+
+ return 0;
+}
+
+static const struct pinconf_ops pm8xxx_pinconf_ops = {
+ .is_generic = true,
+ .pin_config_group_get = pm8xxx_pin_config_get,
+ .pin_config_group_set = pm8xxx_pin_config_set,
+};
+
+static struct pinctrl_desc pm8xxx_pinctrl_desc = {
+ .name = "pm8xxx_gpio",
+ .pctlops = &pm8xxx_pinctrl_ops,
+ .pmxops = &pm8xxx_pinmux_ops,
+ .confops = &pm8xxx_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_gpio_direction_input(struct gpio_chip *chip,
+ unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ u8 val;
+
+ pin->mode = PM8XXX_GPIO_MODE_INPUT;
+ val = pin->mode << 2;
+
+ pm8xxx_write_bank(pctrl, pin, 1, val);
+
+ return 0;
+}
+
+static int pm8xxx_gpio_direction_output(struct gpio_chip *chip,
+ unsigned offset,
+ int value)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ u8 val;
+
+ pin->mode = PM8XXX_GPIO_MODE_OUTPUT;
+ pin->output_value = !!value;
+
+ val = pin->mode << 2;
+ val |= pin->open_drain << 1;
+ val |= pin->output_value;
+
+ pm8xxx_write_bank(pctrl, pin, 1, val);
+
+ return 0;
+}
+
+static int pm8xxx_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ bool state;
+ int ret;
+
+ if (pin->mode == PM8XXX_GPIO_MODE_OUTPUT) {
+ ret = pin->output_value;
+ } else {
+ ret = irq_get_irqchip_state(pin->irq, IRQCHIP_STATE_LINE_LEVEL, &state);
+ if (!ret)
+ ret = !!state;
+ }
+
+ return ret;
+}
+
+static void pm8xxx_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ u8 val;
+
+ pin->output_value = !!value;
+
+ val = pin->mode << 2;
+ val |= pin->open_drain << 1;
+ val |= pin->output_value;
+
+ pm8xxx_write_bank(pctrl, pin, 1, val);
+}
+
+static int pm8xxx_gpio_of_xlate(struct gpio_chip *chip,
+ const struct of_phandle_args *gpio_desc,
+ u32 *flags)
+{
+ if (chip->of_gpio_n_cells < 2)
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpio_desc->args[1];
+
+ return gpio_desc->args[0] - 1;
+}
+
+
+static int pm8xxx_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ return pin->irq;
+}
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/seq_file.h>
+
+static void pm8xxx_gpio_dbg_show_one(struct seq_file *s,
+ struct pinctrl_dev *pctldev,
+ struct gpio_chip *chip,
+ unsigned offset,
+ unsigned gpio)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ static const char * const modes[] = {
+ "in", "both", "out", "off"
+ };
+ static const char * const biases[] = {
+ "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+ "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+ };
+ static const char * const buffer_types[] = {
+ "push-pull", "open-drain"
+ };
+ static const char * const strengths[] = {
+ "no", "high", "medium", "low"
+ };
+
+ seq_printf(s, " gpio%-2d:", offset + 1);
+ if (pin->disable) {
+ seq_puts(s, " ---");
+ } else {
+ seq_printf(s, " %-4s", modes[pin->mode]);
+ seq_printf(s, " %-7s", pm8xxx_gpio_functions[pin->function]);
+ seq_printf(s, " VIN%d", pin->power_source);
+ seq_printf(s, " %-27s", biases[pin->bias]);
+ seq_printf(s, " %-10s", buffer_types[pin->open_drain]);
+ seq_printf(s, " %-4s", pin->output_value ? "high" : "low");
+ seq_printf(s, " %-7s", strengths[pin->output_strength]);
+ if (pin->inverted)
+ seq_puts(s, " inverted");
+ }
+}
+
+static void pm8xxx_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ unsigned gpio = chip->base;
+ unsigned i;
+
+ for (i = 0; i < chip->ngpio; i++, gpio++) {
+ pm8xxx_gpio_dbg_show_one(s, NULL, chip, i, gpio);
+ seq_puts(s, "\n");
+ }
+}
+
+#else
+#define pm8xxx_gpio_dbg_show NULL
+#endif
+
+static struct gpio_chip pm8xxx_gpio_template = {
+ .direction_input = pm8xxx_gpio_direction_input,
+ .direction_output = pm8xxx_gpio_direction_output,
+ .get = pm8xxx_gpio_get,
+ .set = pm8xxx_gpio_set,
+ .of_xlate = pm8xxx_gpio_of_xlate,
+ .to_irq = pm8xxx_gpio_to_irq,
+ .dbg_show = pm8xxx_gpio_dbg_show,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_pin_populate(struct pm8xxx_gpio *pctrl,
+ struct pm8xxx_pin_data *pin)
+{
+ int val;
+
+ val = pm8xxx_read_bank(pctrl, pin, 0);
+ if (val < 0)
+ return val;
+
+ pin->power_source = (val >> 1) & 0x7;
+
+ val = pm8xxx_read_bank(pctrl, pin, 1);
+ if (val < 0)
+ return val;
+
+ pin->mode = (val >> 2) & 0x3;
+ pin->open_drain = !!(val & BIT(1));
+ pin->output_value = val & BIT(0);
+
+ val = pm8xxx_read_bank(pctrl, pin, 2);
+ if (val < 0)
+ return val;
+
+ pin->bias = (val >> 1) & 0x7;
+ if (pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30)
+ pin->pull_up_strength = pin->bias;
+ else
+ pin->pull_up_strength = PM8XXX_GPIO_BIAS_PU_30;
+
+ val = pm8xxx_read_bank(pctrl, pin, 3);
+ if (val < 0)
+ return val;
+
+ pin->output_strength = (val >> 2) & 0x3;
+ pin->disable = val & BIT(0);
+
+ val = pm8xxx_read_bank(pctrl, pin, 4);
+ if (val < 0)
+ return val;
+
+ pin->function = (val >> 1) & 0x7;
+
+ val = pm8xxx_read_bank(pctrl, pin, 5);
+ if (val < 0)
+ return val;
+
+ pin->inverted = !(val & BIT(3));
+
+ return 0;
+}
+
+static const struct of_device_id pm8xxx_gpio_of_match[] = {
+ { .compatible = "qcom,pm8018-gpio", .data = (void *)6 },
+ { .compatible = "qcom,pm8038-gpio", .data = (void *)12 },
+ { .compatible = "qcom,pm8058-gpio", .data = (void *)40 },
+ { .compatible = "qcom,pm8917-gpio", .data = (void *)38 },
+ { .compatible = "qcom,pm8921-gpio", .data = (void *)44 },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_gpio_of_match);
+
+static int pm8xxx_gpio_probe(struct platform_device *pdev)
+{
+ struct pm8xxx_pin_data *pin_data;
+ struct pinctrl_pin_desc *pins;
+ struct pm8xxx_gpio *pctrl;
+ int ret;
+ int i;
+
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ pctrl->dev = &pdev->dev;
+ pctrl->npins = (unsigned)of_device_get_match_data(&pdev->dev);
+
+ pctrl->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!pctrl->regmap) {
+ dev_err(&pdev->dev, "parent regmap unavailable\n");
+ return -ENXIO;
+ }
+
+ pctrl->desc = pm8xxx_pinctrl_desc;
+ pctrl->desc.npins = pctrl->npins;
+
+ pins = devm_kcalloc(&pdev->dev,
+ pctrl->desc.npins,
+ sizeof(struct pinctrl_pin_desc),
+ GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ pin_data = devm_kcalloc(&pdev->dev,
+ pctrl->desc.npins,
+ sizeof(struct pm8xxx_pin_data),
+ GFP_KERNEL);
+ if (!pin_data)
+ return -ENOMEM;
+
+ for (i = 0; i < pctrl->desc.npins; i++) {
+ pin_data[i].reg = SSBI_REG_ADDR_GPIO(i);
+ pin_data[i].irq = platform_get_irq(pdev, i);
+ if (pin_data[i].irq < 0) {
+ dev_err(&pdev->dev,
+ "missing interrupts for pin %d\n", i);
+ return pin_data[i].irq;
+ }
+
+ ret = pm8xxx_pin_populate(pctrl, &pin_data[i]);
+ if (ret)
+ return ret;
+
+ pins[i].number = i;
+ pins[i].name = pm8xxx_groups[i];
+ pins[i].drv_data = &pin_data[i];
+ }
+ pctrl->desc.pins = pins;
+
+ pctrl->desc.num_custom_params = ARRAY_SIZE(pm8xxx_gpio_bindings);
+ pctrl->desc.custom_params = pm8xxx_gpio_bindings;
+#ifdef CONFIG_DEBUG_FS
+ pctrl->desc.custom_conf_items = pm8xxx_conf_items;
+#endif
+
+ pctrl->pctrl = pinctrl_register(&pctrl->desc, &pdev->dev, pctrl);
+ if (IS_ERR(pctrl->pctrl)) {
+ dev_err(&pdev->dev, "couldn't register pm8xxx gpio driver\n");
+ return PTR_ERR(pctrl->pctrl);
+ }
+
+ pctrl->chip = pm8xxx_gpio_template;
+ pctrl->chip.base = -1;
+ pctrl->chip.dev = &pdev->dev;
+ pctrl->chip.of_node = pdev->dev.of_node;
+ pctrl->chip.of_gpio_n_cells = 2;
+ pctrl->chip.label = dev_name(pctrl->dev);
+ pctrl->chip.ngpio = pctrl->npins;
+ ret = gpiochip_add(&pctrl->chip);
+ if (ret) {
+ dev_err(&pdev->dev, "failed register gpiochip\n");
+ goto unregister_pinctrl;
+ }
+
+ ret = gpiochip_add_pin_range(&pctrl->chip,
+ dev_name(pctrl->dev),
+ 0, 0, pctrl->chip.ngpio);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to add pin range\n");
+ goto unregister_gpiochip;
+ }
+
+ platform_set_drvdata(pdev, pctrl);
+
+ dev_dbg(&pdev->dev, "Qualcomm pm8xxx gpio driver probed\n");
+
+ return 0;
+
+unregister_gpiochip:
+ gpiochip_remove(&pctrl->chip);
+
+unregister_pinctrl:
+ pinctrl_unregister(pctrl->pctrl);
+
+ return ret;
+}
+
+static int pm8xxx_gpio_remove(struct platform_device *pdev)
+{
+ struct pm8xxx_gpio *pctrl = platform_get_drvdata(pdev);
+
+ gpiochip_remove(&pctrl->chip);
+
+ pinctrl_unregister(pctrl->pctrl);
+
+ return 0;
+}
+
+static struct platform_driver pm8xxx_gpio_driver = {
+ .driver = {
+ .name = "qcom-ssbi-gpio",
+ .of_match_table = pm8xxx_gpio_of_match,
+ },
+ .probe = pm8xxx_gpio_probe,
+ .remove = pm8xxx_gpio_remove,
+};
+
+module_platform_driver(pm8xxx_gpio_driver);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm PM8xxx GPIO driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c b/drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c
new file mode 100644
index 000000000..8982027de
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-mpp.c
@@ -0,0 +1,882 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/of_device.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+/* MPP registers */
+#define SSBI_REG_ADDR_MPP_BASE 0x50
+#define SSBI_REG_ADDR_MPP(n) (SSBI_REG_ADDR_MPP_BASE + n)
+
+/* MPP Type: type */
+#define PM8XXX_MPP_TYPE_D_INPUT 0
+#define PM8XXX_MPP_TYPE_D_OUTPUT 1
+#define PM8XXX_MPP_TYPE_D_BI_DIR 2
+#define PM8XXX_MPP_TYPE_A_INPUT 3
+#define PM8XXX_MPP_TYPE_A_OUTPUT 4
+#define PM8XXX_MPP_TYPE_SINK 5
+#define PM8XXX_MPP_TYPE_DTEST_SINK 6
+#define PM8XXX_MPP_TYPE_DTEST_OUTPUT 7
+
+/* Digital Input: control */
+#define PM8XXX_MPP_DIN_TO_INT 0
+#define PM8XXX_MPP_DIN_TO_DBUS1 1
+#define PM8XXX_MPP_DIN_TO_DBUS2 2
+#define PM8XXX_MPP_DIN_TO_DBUS3 3
+
+/* Digital Output: control */
+#define PM8XXX_MPP_DOUT_CTRL_LOW 0
+#define PM8XXX_MPP_DOUT_CTRL_HIGH 1
+#define PM8XXX_MPP_DOUT_CTRL_MPP 2
+#define PM8XXX_MPP_DOUT_CTRL_INV_MPP 3
+
+/* Bidirectional: control */
+#define PM8XXX_MPP_BI_PULLUP_1KOHM 0
+#define PM8XXX_MPP_BI_PULLUP_OPEN 1
+#define PM8XXX_MPP_BI_PULLUP_10KOHM 2
+#define PM8XXX_MPP_BI_PULLUP_30KOHM 3
+
+/* Analog Output: control */
+#define PM8XXX_MPP_AOUT_CTRL_DISABLE 0
+#define PM8XXX_MPP_AOUT_CTRL_ENABLE 1
+#define PM8XXX_MPP_AOUT_CTRL_MPP_HIGH_EN 2
+#define PM8XXX_MPP_AOUT_CTRL_MPP_LOW_EN 3
+
+/* Current Sink: control */
+#define PM8XXX_MPP_CS_CTRL_DISABLE 0
+#define PM8XXX_MPP_CS_CTRL_ENABLE 1
+#define PM8XXX_MPP_CS_CTRL_MPP_HIGH_EN 2
+#define PM8XXX_MPP_CS_CTRL_MPP_LOW_EN 3
+
+/* DTEST Current Sink: control */
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN1 0
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN2 1
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN3 2
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN4 3
+
+/* DTEST Digital Output: control */
+#define PM8XXX_MPP_DTEST_DBUS1 0
+#define PM8XXX_MPP_DTEST_DBUS2 1
+#define PM8XXX_MPP_DTEST_DBUS3 2
+#define PM8XXX_MPP_DTEST_DBUS4 3
+
+/* custom pinconf parameters */
+#define PM8XXX_CONFIG_AMUX (PIN_CONFIG_END + 1)
+#define PM8XXX_CONFIG_DTEST_SELECTOR (PIN_CONFIG_END + 2)
+#define PM8XXX_CONFIG_ALEVEL (PIN_CONFIG_END + 3)
+#define PM8XXX_CONFIG_PAIRED (PIN_CONFIG_END + 4)
+
+/**
+ * struct pm8xxx_pin_data - dynamic configuration for a pin
+ * @reg: address of the control register
+ * @irq: IRQ from the PMIC interrupt controller
+ * @mode: operating mode for the pin (digital, analog or current sink)
+ * @input: pin is input
+ * @output: pin is output
+ * @high_z: pin is floating
+ * @paired: mpp operates in paired mode
+ * @output_value: logical output value of the mpp
+ * @power_source: selected power source
+ * @dtest: DTEST route selector
+ * @amux: input muxing in analog mode
+ * @aout_level: selector of the output in analog mode
+ * @drive_strength: drive strength of the current sink
+ * @pullup: pull up value, when in digital bidirectional mode
+ */
+struct pm8xxx_pin_data {
+ unsigned reg;
+ int irq;
+
+ u8 mode;
+
+ bool input;
+ bool output;
+ bool high_z;
+ bool paired;
+ bool output_value;
+
+ u8 power_source;
+ u8 dtest;
+ u8 amux;
+ u8 aout_level;
+ u8 drive_strength;
+ unsigned pullup;
+};
+
+struct pm8xxx_mpp {
+ struct device *dev;
+ struct regmap *regmap;
+ struct pinctrl_dev *pctrl;
+ struct gpio_chip chip;
+
+ struct pinctrl_desc desc;
+ unsigned npins;
+};
+
+static const struct pinconf_generic_params pm8xxx_mpp_bindings[] = {
+ {"qcom,amux-route", PM8XXX_CONFIG_AMUX, 0},
+ {"qcom,analog-level", PM8XXX_CONFIG_ALEVEL, 0},
+ {"qcom,dtest", PM8XXX_CONFIG_DTEST_SELECTOR, 0},
+ {"qcom,paired", PM8XXX_CONFIG_PAIRED, 0},
+};
+
+#ifdef CONFIG_DEBUG_FS
+static const struct pin_config_item pm8xxx_conf_items[] = {
+ PCONFDUMP(PM8XXX_CONFIG_AMUX, "analog mux", NULL, true),
+ PCONFDUMP(PM8XXX_CONFIG_ALEVEL, "analog level", NULL, true),
+ PCONFDUMP(PM8XXX_CONFIG_DTEST_SELECTOR, "dtest", NULL, true),
+ PCONFDUMP(PM8XXX_CONFIG_PAIRED, "paired", NULL, false),
+};
+#endif
+
+#define PM8XXX_MAX_MPPS 12
+static const char * const pm8xxx_groups[PM8XXX_MAX_MPPS] = {
+ "mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
+ "mpp9", "mpp10", "mpp11", "mpp12",
+};
+
+#define PM8XXX_MPP_DIGITAL 0
+#define PM8XXX_MPP_ANALOG 1
+#define PM8XXX_MPP_SINK 2
+
+static const char * const pm8xxx_mpp_functions[] = {
+ "digital", "analog", "sink",
+};
+
+static int pm8xxx_mpp_update(struct pm8xxx_mpp *pctrl,
+ struct pm8xxx_pin_data *pin)
+{
+ unsigned level;
+ unsigned ctrl;
+ unsigned type;
+ int ret;
+ u8 val;
+
+ switch (pin->mode) {
+ case PM8XXX_MPP_DIGITAL:
+ if (pin->dtest) {
+ type = PM8XXX_MPP_TYPE_DTEST_OUTPUT;
+ ctrl = pin->dtest - 1;
+ } else if (pin->input && pin->output) {
+ type = PM8XXX_MPP_TYPE_D_BI_DIR;
+ if (pin->high_z)
+ ctrl = PM8XXX_MPP_BI_PULLUP_OPEN;
+ else if (pin->pullup == 600)
+ ctrl = PM8XXX_MPP_BI_PULLUP_1KOHM;
+ else if (pin->pullup == 10000)
+ ctrl = PM8XXX_MPP_BI_PULLUP_10KOHM;
+ else
+ ctrl = PM8XXX_MPP_BI_PULLUP_30KOHM;
+ } else if (pin->input) {
+ type = PM8XXX_MPP_TYPE_D_INPUT;
+ if (pin->dtest)
+ ctrl = pin->dtest;
+ else
+ ctrl = PM8XXX_MPP_DIN_TO_INT;
+ } else {
+ type = PM8XXX_MPP_TYPE_D_OUTPUT;
+ ctrl = !!pin->output_value;
+ if (pin->paired)
+ ctrl |= BIT(1);
+ }
+
+ level = pin->power_source;
+ break;
+ case PM8XXX_MPP_ANALOG:
+ if (pin->output) {
+ type = PM8XXX_MPP_TYPE_A_OUTPUT;
+ level = pin->aout_level;
+ ctrl = pin->output_value;
+ if (pin->paired)
+ ctrl |= BIT(1);
+ } else {
+ type = PM8XXX_MPP_TYPE_A_INPUT;
+ level = pin->amux;
+ ctrl = 0;
+ }
+ break;
+ case PM8XXX_MPP_SINK:
+ level = (pin->drive_strength / 5) - 1;
+ if (pin->dtest) {
+ type = PM8XXX_MPP_TYPE_DTEST_SINK;
+ ctrl = pin->dtest - 1;
+ } else {
+ type = PM8XXX_MPP_TYPE_SINK;
+ ctrl = pin->output_value;
+ if (pin->paired)
+ ctrl |= BIT(1);
+ }
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val = type << 5 | level << 2 | ctrl;
+ ret = regmap_write(pctrl->regmap, pin->reg, val);
+ if (ret)
+ dev_err(pctrl->dev, "failed to write register\n");
+
+ return ret;
+}
+
+static int pm8xxx_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->npins;
+}
+
+static const char *pm8xxx_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned group)
+{
+ return pm8xxx_groups[group];
+}
+
+
+static int pm8xxx_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned group,
+ const unsigned **pins,
+ unsigned *num_pins)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = &pctrl->desc.pins[group].number;
+ *num_pins = 1;
+
+ return 0;
+}
+
+static const struct pinctrl_ops pm8xxx_pinctrl_ops = {
+ .get_groups_count = pm8xxx_get_groups_count,
+ .get_group_name = pm8xxx_get_group_name,
+ .get_group_pins = pm8xxx_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int pm8xxx_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(pm8xxx_mpp_functions);
+}
+
+static const char *pm8xxx_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return pm8xxx_mpp_functions[function];
+}
+
+static int pm8xxx_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = pm8xxx_groups;
+ *num_groups = pctrl->npins;
+ return 0;
+}
+
+static int pm8xxx_pinmux_set_mux(struct pinctrl_dev *pctldev,
+ unsigned function,
+ unsigned group)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[group].drv_data;
+
+ pin->mode = function;
+ pm8xxx_mpp_update(pctrl, pin);
+
+ return 0;
+}
+
+static const struct pinmux_ops pm8xxx_pinmux_ops = {
+ .get_functions_count = pm8xxx_get_functions_count,
+ .get_function_name = pm8xxx_get_function_name,
+ .get_function_groups = pm8xxx_get_function_groups,
+ .set_mux = pm8xxx_pinmux_set_mux,
+};
+
+static int pm8xxx_pin_config_get(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *config)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ unsigned param = pinconf_to_config_param(*config);
+ unsigned arg;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_PULL_UP:
+ arg = pin->pullup;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ arg = pin->high_z;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ arg = pin->input;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ arg = pin->output_value;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = pin->power_source;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ arg = pin->drive_strength;
+ break;
+ case PM8XXX_CONFIG_DTEST_SELECTOR:
+ arg = pin->dtest;
+ break;
+ case PM8XXX_CONFIG_AMUX:
+ arg = pin->amux;
+ break;
+ case PM8XXX_CONFIG_ALEVEL:
+ arg = pin->aout_level;
+ break;
+ case PM8XXX_CONFIG_PAIRED:
+ arg = pin->paired;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *configs,
+ unsigned num_configs)
+{
+ struct pm8xxx_mpp *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ unsigned param;
+ unsigned arg;
+ unsigned i;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_PULL_UP:
+ pin->pullup = arg;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ pin->high_z = true;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ pin->input = true;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ pin->output = true;
+ pin->output_value = !!arg;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ pin->power_source = arg;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ pin->drive_strength = arg;
+ break;
+ case PM8XXX_CONFIG_DTEST_SELECTOR:
+ pin->dtest = arg;
+ break;
+ case PM8XXX_CONFIG_AMUX:
+ pin->amux = arg;
+ break;
+ case PM8XXX_CONFIG_ALEVEL:
+ pin->aout_level = arg;
+ break;
+ case PM8XXX_CONFIG_PAIRED:
+ pin->paired = !!arg;
+ break;
+ default:
+ dev_err(pctrl->dev,
+ "unsupported config parameter: %x\n",
+ param);
+ return -EINVAL;
+ }
+ }
+
+ pm8xxx_mpp_update(pctrl, pin);
+
+ return 0;
+}
+
+static const struct pinconf_ops pm8xxx_pinconf_ops = {
+ .is_generic = true,
+ .pin_config_group_get = pm8xxx_pin_config_get,
+ .pin_config_group_set = pm8xxx_pin_config_set,
+};
+
+static struct pinctrl_desc pm8xxx_pinctrl_desc = {
+ .name = "pm8xxx_mpp",
+ .pctlops = &pm8xxx_pinctrl_ops,
+ .pmxops = &pm8xxx_pinmux_ops,
+ .confops = &pm8xxx_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_mpp_direction_input(struct gpio_chip *chip,
+ unsigned offset)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ switch (pin->mode) {
+ case PM8XXX_MPP_DIGITAL:
+ pin->input = true;
+ break;
+ case PM8XXX_MPP_ANALOG:
+ pin->input = true;
+ pin->output = true;
+ break;
+ case PM8XXX_MPP_SINK:
+ return -EINVAL;
+ }
+
+ pm8xxx_mpp_update(pctrl, pin);
+
+ return 0;
+}
+
+static int pm8xxx_mpp_direction_output(struct gpio_chip *chip,
+ unsigned offset,
+ int value)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ switch (pin->mode) {
+ case PM8XXX_MPP_DIGITAL:
+ pin->output = true;
+ break;
+ case PM8XXX_MPP_ANALOG:
+ pin->input = false;
+ pin->output = true;
+ break;
+ case PM8XXX_MPP_SINK:
+ pin->input = false;
+ pin->output = true;
+ break;
+ }
+
+ pm8xxx_mpp_update(pctrl, pin);
+
+ return 0;
+}
+
+static int pm8xxx_mpp_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+ bool state;
+ int ret;
+
+ if (!pin->input)
+ return pin->output_value;
+
+ ret = irq_get_irqchip_state(pin->irq, IRQCHIP_STATE_LINE_LEVEL, &state);
+ if (!ret)
+ ret = !!state;
+
+ return ret;
+}
+
+static void pm8xxx_mpp_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ pin->output_value = !!value;
+
+ pm8xxx_mpp_update(pctrl, pin);
+}
+
+static int pm8xxx_mpp_of_xlate(struct gpio_chip *chip,
+ const struct of_phandle_args *gpio_desc,
+ u32 *flags)
+{
+ if (chip->of_gpio_n_cells < 2)
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpio_desc->args[1];
+
+ return gpio_desc->args[0] - 1;
+}
+
+
+static int pm8xxx_mpp_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ return pin->irq;
+}
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/seq_file.h>
+
+static void pm8xxx_mpp_dbg_show_one(struct seq_file *s,
+ struct pinctrl_dev *pctldev,
+ struct gpio_chip *chip,
+ unsigned offset,
+ unsigned gpio)
+{
+ struct pm8xxx_mpp *pctrl = container_of(chip, struct pm8xxx_mpp, chip);
+ struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+ static const char * const aout_lvls[] = {
+ "1v25", "1v25_2", "0v625", "0v3125", "mpp", "abus1", "abus2",
+ "abus3"
+ };
+
+ static const char * const amuxs[] = {
+ "amux5", "amux6", "amux7", "amux8", "amux9", "abus1", "abus2",
+ "abus3",
+ };
+
+ seq_printf(s, " mpp%-2d:", offset + 1);
+
+ switch (pin->mode) {
+ case PM8XXX_MPP_DIGITAL:
+ seq_puts(s, " digital ");
+ if (pin->dtest) {
+ seq_printf(s, "dtest%d\n", pin->dtest);
+ } else if (pin->input && pin->output) {
+ if (pin->high_z)
+ seq_puts(s, "bi-dir high-z");
+ else
+ seq_printf(s, "bi-dir %dOhm", pin->pullup);
+ } else if (pin->input) {
+ if (pin->dtest)
+ seq_printf(s, "in dtest%d", pin->dtest);
+ else
+ seq_puts(s, "in gpio");
+ } else if (pin->output) {
+ seq_puts(s, "out ");
+
+ if (!pin->paired) {
+ seq_puts(s, pin->output_value ?
+ "high" : "low");
+ } else {
+ seq_puts(s, pin->output_value ?
+ "inverted" : "follow");
+ }
+ }
+ break;
+ case PM8XXX_MPP_ANALOG:
+ seq_puts(s, " analog ");
+ if (pin->output) {
+ seq_printf(s, "out %s ", aout_lvls[pin->aout_level]);
+ if (!pin->paired) {
+ seq_puts(s, pin->output_value ?
+ "high" : "low");
+ } else {
+ seq_puts(s, pin->output_value ?
+ "inverted" : "follow");
+ }
+ } else {
+ seq_printf(s, "input mux %s", amuxs[pin->amux]);
+ }
+ break;
+ case PM8XXX_MPP_SINK:
+ seq_printf(s, " sink %dmA ", pin->drive_strength);
+ if (pin->dtest) {
+ seq_printf(s, "dtest%d", pin->dtest);
+ } else {
+ if (!pin->paired) {
+ seq_puts(s, pin->output_value ?
+ "high" : "low");
+ } else {
+ seq_puts(s, pin->output_value ?
+ "inverted" : "follow");
+ }
+ }
+ break;
+ }
+
+}
+
+static void pm8xxx_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ unsigned gpio = chip->base;
+ unsigned i;
+
+ for (i = 0; i < chip->ngpio; i++, gpio++) {
+ pm8xxx_mpp_dbg_show_one(s, NULL, chip, i, gpio);
+ seq_puts(s, "\n");
+ }
+}
+
+#else
+#define pm8xxx_mpp_dbg_show NULL
+#endif
+
+static struct gpio_chip pm8xxx_mpp_template = {
+ .direction_input = pm8xxx_mpp_direction_input,
+ .direction_output = pm8xxx_mpp_direction_output,
+ .get = pm8xxx_mpp_get,
+ .set = pm8xxx_mpp_set,
+ .of_xlate = pm8xxx_mpp_of_xlate,
+ .to_irq = pm8xxx_mpp_to_irq,
+ .dbg_show = pm8xxx_mpp_dbg_show,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_pin_populate(struct pm8xxx_mpp *pctrl,
+ struct pm8xxx_pin_data *pin)
+{
+ unsigned int val;
+ unsigned level;
+ unsigned ctrl;
+ unsigned type;
+ int ret;
+
+ ret = regmap_read(pctrl->regmap, pin->reg, &val);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to read register\n");
+ return ret;
+ }
+
+ type = (val >> 5) & 7;
+ level = (val >> 2) & 7;
+ ctrl = (val) & 3;
+
+ switch (type) {
+ case PM8XXX_MPP_TYPE_D_INPUT:
+ pin->mode = PM8XXX_MPP_DIGITAL;
+ pin->input = true;
+ pin->power_source = level;
+ pin->dtest = ctrl;
+ break;
+ case PM8XXX_MPP_TYPE_D_OUTPUT:
+ pin->mode = PM8XXX_MPP_DIGITAL;
+ pin->output = true;
+ pin->power_source = level;
+ pin->output_value = !!(ctrl & BIT(0));
+ pin->paired = !!(ctrl & BIT(1));
+ break;
+ case PM8XXX_MPP_TYPE_D_BI_DIR:
+ pin->mode = PM8XXX_MPP_DIGITAL;
+ pin->input = true;
+ pin->output = true;
+ pin->power_source = level;
+ switch (ctrl) {
+ case PM8XXX_MPP_BI_PULLUP_1KOHM:
+ pin->pullup = 600;
+ break;
+ case PM8XXX_MPP_BI_PULLUP_OPEN:
+ pin->high_z = true;
+ break;
+ case PM8XXX_MPP_BI_PULLUP_10KOHM:
+ pin->pullup = 10000;
+ break;
+ case PM8XXX_MPP_BI_PULLUP_30KOHM:
+ pin->pullup = 30000;
+ break;
+ }
+ break;
+ case PM8XXX_MPP_TYPE_A_INPUT:
+ pin->mode = PM8XXX_MPP_ANALOG;
+ pin->input = true;
+ pin->amux = level;
+ break;
+ case PM8XXX_MPP_TYPE_A_OUTPUT:
+ pin->mode = PM8XXX_MPP_ANALOG;
+ pin->output = true;
+ pin->aout_level = level;
+ pin->output_value = !!(ctrl & BIT(0));
+ pin->paired = !!(ctrl & BIT(1));
+ break;
+ case PM8XXX_MPP_TYPE_SINK:
+ pin->mode = PM8XXX_MPP_SINK;
+ pin->drive_strength = 5 * (level + 1);
+ pin->output_value = !!(ctrl & BIT(0));
+ pin->paired = !!(ctrl & BIT(1));
+ break;
+ case PM8XXX_MPP_TYPE_DTEST_SINK:
+ pin->mode = PM8XXX_MPP_SINK;
+ pin->dtest = ctrl + 1;
+ pin->drive_strength = 5 * (level + 1);
+ break;
+ case PM8XXX_MPP_TYPE_DTEST_OUTPUT:
+ pin->mode = PM8XXX_MPP_DIGITAL;
+ pin->power_source = level;
+ if (ctrl >= 1)
+ pin->dtest = ctrl;
+ break;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id pm8xxx_mpp_of_match[] = {
+ { .compatible = "qcom,pm8018-mpp", .data = (void *)6 },
+ { .compatible = "qcom,pm8038-mpp", .data = (void *)6 },
+ { .compatible = "qcom,pm8917-mpp", .data = (void *)10 },
+ { .compatible = "qcom,pm8821-mpp", .data = (void *)4 },
+ { .compatible = "qcom,pm8921-mpp", .data = (void *)12 },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_mpp_of_match);
+
+static int pm8xxx_mpp_probe(struct platform_device *pdev)
+{
+ struct pm8xxx_pin_data *pin_data;
+ struct pinctrl_pin_desc *pins;
+ struct pm8xxx_mpp *pctrl;
+ int ret;
+ int i;
+
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ pctrl->dev = &pdev->dev;
+ pctrl->npins = (unsigned)of_device_get_match_data(&pdev->dev);
+
+ pctrl->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!pctrl->regmap) {
+ dev_err(&pdev->dev, "parent regmap unavailable\n");
+ return -ENXIO;
+ }
+
+ pctrl->desc = pm8xxx_pinctrl_desc;
+ pctrl->desc.npins = pctrl->npins;
+
+ pins = devm_kcalloc(&pdev->dev,
+ pctrl->desc.npins,
+ sizeof(struct pinctrl_pin_desc),
+ GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ pin_data = devm_kcalloc(&pdev->dev,
+ pctrl->desc.npins,
+ sizeof(struct pm8xxx_pin_data),
+ GFP_KERNEL);
+ if (!pin_data)
+ return -ENOMEM;
+
+ for (i = 0; i < pctrl->desc.npins; i++) {
+ pin_data[i].reg = SSBI_REG_ADDR_MPP(i);
+ pin_data[i].irq = platform_get_irq(pdev, i);
+ if (pin_data[i].irq < 0) {
+ dev_err(&pdev->dev,
+ "missing interrupts for pin %d\n", i);
+ return pin_data[i].irq;
+ }
+
+ ret = pm8xxx_pin_populate(pctrl, &pin_data[i]);
+ if (ret)
+ return ret;
+
+ pins[i].number = i;
+ pins[i].name = pm8xxx_groups[i];
+ pins[i].drv_data = &pin_data[i];
+ }
+ pctrl->desc.pins = pins;
+
+ pctrl->desc.num_custom_params = ARRAY_SIZE(pm8xxx_mpp_bindings);
+ pctrl->desc.custom_params = pm8xxx_mpp_bindings;
+#ifdef CONFIG_DEBUG_FS
+ pctrl->desc.custom_conf_items = pm8xxx_conf_items;
+#endif
+
+ pctrl->pctrl = pinctrl_register(&pctrl->desc, &pdev->dev, pctrl);
+ if (IS_ERR(pctrl->pctrl)) {
+ dev_err(&pdev->dev, "couldn't register pm8xxx mpp driver\n");
+ return PTR_ERR(pctrl->pctrl);
+ }
+
+ pctrl->chip = pm8xxx_mpp_template;
+ pctrl->chip.base = -1;
+ pctrl->chip.dev = &pdev->dev;
+ pctrl->chip.of_node = pdev->dev.of_node;
+ pctrl->chip.of_gpio_n_cells = 2;
+ pctrl->chip.label = dev_name(pctrl->dev);
+ pctrl->chip.ngpio = pctrl->npins;
+ ret = gpiochip_add(&pctrl->chip);
+ if (ret) {
+ dev_err(&pdev->dev, "failed register gpiochip\n");
+ goto unregister_pinctrl;
+ }
+
+ ret = gpiochip_add_pin_range(&pctrl->chip,
+ dev_name(pctrl->dev),
+ 0, 0, pctrl->chip.ngpio);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to add pin range\n");
+ goto unregister_gpiochip;
+ }
+
+ platform_set_drvdata(pdev, pctrl);
+
+ dev_dbg(&pdev->dev, "Qualcomm pm8xxx mpp driver probed\n");
+
+ return 0;
+
+unregister_gpiochip:
+ gpiochip_remove(&pctrl->chip);
+
+unregister_pinctrl:
+ pinctrl_unregister(pctrl->pctrl);
+
+ return ret;
+}
+
+static int pm8xxx_mpp_remove(struct platform_device *pdev)
+{
+ struct pm8xxx_mpp *pctrl = platform_get_drvdata(pdev);
+
+ gpiochip_remove(&pctrl->chip);
+
+ pinctrl_unregister(pctrl->pctrl);
+
+ return 0;
+}
+
+static struct platform_driver pm8xxx_mpp_driver = {
+ .driver = {
+ .name = "qcom-ssbi-mpp",
+ .of_match_table = pm8xxx_mpp_of_match,
+ },
+ .probe = pm8xxx_mpp_probe,
+ .remove = pm8xxx_mpp_remove,
+};
+
+module_platform_driver(pm8xxx_mpp_driver);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm PM8xxx MPP driver");
+MODULE_LICENSE("GPL v2");
generated by cgit v1.2.3-54-g00ecf (git 2.45.2) at 2024-11-17 02:15:23 +0000