diff options
Diffstat (limited to 'drivers/usb/core/hub.c')
| -rw-r--r-- | drivers/usb/core/hub.c | 39 |
1 files changed, 26 insertions, 13 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 1560f3f3e..51b436918 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -3324,7 +3324,7 @@ static int finish_port_resume(struct usb_device *udev) /* * There are some SS USB devices which take longer time for link training. * XHCI specs 4.19.4 says that when Link training is successful, port - * sets CSC bit to 1. So if SW reads port status before successful link + * sets CCS bit to 1. So if SW reads port status before successful link * training, then it will not find device to be present. * USB Analyzer log with such buggy devices show that in some cases * device switch on the RX termination after long delay of host enabling @@ -3335,14 +3335,17 @@ static int finish_port_resume(struct usb_device *udev) * routine implements a 2000 ms timeout for link training. If in a case * link trains before timeout, loop will exit earlier. * + * There are also some 2.0 hard drive based devices and 3.0 thumb + * drives that, when plugged into a 2.0 only port, take a long + * time to set CCS after VBUS enable. + * * FIXME: If a device was connected before suspend, but was removed * while system was asleep, then the loop in the following routine will * only exit at timeout. * - * This routine should only be called when persist is enabled for a SS - * device. + * This routine should only be called when persist is enabled. */ -static int wait_for_ss_port_enable(struct usb_device *udev, +static int wait_for_connected(struct usb_device *udev, struct usb_hub *hub, int *port1, u16 *portchange, u16 *portstatus) { @@ -3355,6 +3358,7 @@ static int wait_for_ss_port_enable(struct usb_device *udev, delay_ms += 20; status = hub_port_status(hub, *port1, portstatus, portchange); } + dev_dbg(&udev->dev, "Waited %dms for CONNECT\n", delay_ms); return status; } @@ -3454,8 +3458,8 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) } } - if (udev->persist_enabled && hub_is_superspeed(hub->hdev)) - status = wait_for_ss_port_enable(udev, hub, &port1, &portchange, + if (udev->persist_enabled) + status = wait_for_connected(udev, hub, &port1, &portchange, &portstatus); status = check_port_resume_type(udev, @@ -4040,6 +4044,8 @@ EXPORT_SYMBOL_GPL(usb_unlocked_disable_lpm); void usb_enable_lpm(struct usb_device *udev) { struct usb_hcd *hcd; + struct usb_hub *hub; + struct usb_port *port_dev; if (!udev || !udev->parent || udev->speed != USB_SPEED_SUPER || @@ -4059,8 +4065,17 @@ void usb_enable_lpm(struct usb_device *udev) if (udev->lpm_disable_count > 0) return; - usb_enable_link_state(hcd, udev, USB3_LPM_U1); - usb_enable_link_state(hcd, udev, USB3_LPM_U2); + hub = usb_hub_to_struct_hub(udev->parent); + if (!hub) + return; + + port_dev = hub->ports[udev->portnum - 1]; + + if (port_dev->usb3_lpm_u1_permit) + usb_enable_link_state(hcd, udev, USB3_LPM_U1); + + if (port_dev->usb3_lpm_u2_permit) + usb_enable_link_state(hcd, udev, USB3_LPM_U2); } EXPORT_SYMBOL_GPL(usb_enable_lpm); @@ -5386,6 +5401,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) } bos = udev->bos; + udev->bos = NULL; for (i = 0; i < SET_CONFIG_TRIES; ++i) { @@ -5478,11 +5494,8 @@ done: usb_set_usb2_hardware_lpm(udev, 1); usb_unlocked_enable_lpm(udev); usb_enable_ltm(udev); - /* release the new BOS descriptor allocated by hub_port_init() */ - if (udev->bos != bos) { - usb_release_bos_descriptor(udev); - udev->bos = bos; - } + usb_release_bos_descriptor(udev); + udev->bos = bos; return 0; re_enumerate: |