diff options
Diffstat (limited to 'drivers/usb/host/uhci-pci.c')
| -rw-r--r-- | drivers/usb/host/uhci-pci.c | 306 |
1 files changed, 306 insertions, 0 deletions
diff --git a/drivers/usb/host/uhci-pci.c b/drivers/usb/host/uhci-pci.c new file mode 100644 index 000000000..940304c33 --- /dev/null +++ b/drivers/usb/host/uhci-pci.c @@ -0,0 +1,306 @@ +/* + * UHCI HCD (Host Controller Driver) PCI Bus Glue. + * + * Extracted from uhci-hcd.c: + * Maintainer: Alan Stern <stern@rowland.harvard.edu> + * + * (C) Copyright 1999 Linus Torvalds + * (C) Copyright 1999-2002 Johannes Erdfelt, johannes@erdfelt.com + * (C) Copyright 1999 Randy Dunlap + * (C) Copyright 1999 Georg Acher, acher@in.tum.de + * (C) Copyright 1999 Deti Fliegl, deti@fliegl.de + * (C) Copyright 1999 Thomas Sailer, sailer@ife.ee.ethz.ch + * (C) Copyright 1999 Roman Weissgaerber, weissg@vienna.at + * (C) Copyright 2000 Yggdrasil Computing, Inc. (port of new PCI interface + * support from usb-ohci.c by Adam Richter, adam@yggdrasil.com). + * (C) Copyright 1999 Gregory P. Smith (from usb-ohci.c) + * (C) Copyright 2004-2007 Alan Stern, stern@rowland.harvard.edu + */ + +#include "pci-quirks.h" + +/* + * Make sure the controller is completely inactive, unable to + * generate interrupts or do DMA. + */ +static void uhci_pci_reset_hc(struct uhci_hcd *uhci) +{ + uhci_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr); +} + +/* + * Initialize a controller that was newly discovered or has just been + * resumed. In either case we can't be sure of its previous state. + * + * Returns: 1 if the controller was reset, 0 otherwise. + */ +static int uhci_pci_check_and_reset_hc(struct uhci_hcd *uhci) +{ + return uhci_check_and_reset_hc(to_pci_dev(uhci_dev(uhci)), + uhci->io_addr); +} + +/* + * Store the basic register settings needed by the controller. + * This function is called at the end of configure_hc in uhci-hcd.c. + */ +static void uhci_pci_configure_hc(struct uhci_hcd *uhci) +{ + struct pci_dev *pdev = to_pci_dev(uhci_dev(uhci)); + + /* Enable PIRQ */ + pci_write_config_word(pdev, USBLEGSUP, USBLEGSUP_DEFAULT); + + /* Disable platform-specific non-PME# wakeup */ + if (pdev->vendor == PCI_VENDOR_ID_INTEL) + pci_write_config_byte(pdev, USBRES_INTEL, 0); +} + +static int uhci_pci_resume_detect_interrupts_are_broken(struct uhci_hcd *uhci) +{ + int port; + + switch (to_pci_dev(uhci_dev(uhci))->vendor) { + default: + break; + + case PCI_VENDOR_ID_GENESYS: + /* Genesys Logic's GL880S controllers don't generate + * resume-detect interrupts. + */ + return 1; + + case PCI_VENDOR_ID_INTEL: + /* Some of Intel's USB controllers have a bug that causes + * resume-detect interrupts if any port has an over-current + * condition. To make matters worse, some motherboards + * hardwire unused USB ports' over-current inputs active! + * To prevent problems, we will not enable resume-detect + * interrupts if any ports are OC. + */ + for (port = 0; port < uhci->rh_numports; ++port) { + if (inw(uhci->io_addr + USBPORTSC1 + port * 2) & + USBPORTSC_OC) + return 1; + } + break; + } + return 0; +} + +static int uhci_pci_global_suspend_mode_is_broken(struct uhci_hcd *uhci) +{ + int port; + const char *sys_info; + static const char bad_Asus_board[] = "A7V8X"; + + /* One of Asus's motherboards has a bug which causes it to + * wake up immediately from suspend-to-RAM if any of the ports + * are connected. In such cases we will not set EGSM. + */ + sys_info = dmi_get_system_info(DMI_BOARD_NAME); + if (sys_info && !strcmp(sys_info, bad_Asus_board)) { + for (port = 0; port < uhci->rh_numports; ++port) { + if (inw(uhci->io_addr + USBPORTSC1 + port * 2) & + USBPORTSC_CCS) + return 1; + } + } + + return 0; +} + +static int uhci_pci_init(struct usb_hcd *hcd) +{ + struct uhci_hcd *uhci = hcd_to_uhci(hcd); + + uhci->io_addr = (unsigned long) hcd->rsrc_start; + + uhci->rh_numports = uhci_count_ports(hcd); + + /* Intel controllers report the OverCurrent bit active on. + * VIA controllers report it active off, so we'll adjust the + * bit value. (It's not standardized in the UHCI spec.) + */ + if (to_pci_dev(uhci_dev(uhci))->vendor == PCI_VENDOR_ID_VIA) + uhci->oc_low = 1; + + /* HP's server management chip requires a longer port reset delay. */ + if (to_pci_dev(uhci_dev(uhci))->vendor == PCI_VENDOR_ID_HP) + uhci->wait_for_hp = 1; + + /* Set up pointers to PCI-specific functions */ + uhci->reset_hc = uhci_pci_reset_hc; + uhci->check_and_reset_hc = uhci_pci_check_and_reset_hc; + uhci->configure_hc = uhci_pci_configure_hc; + uhci->resume_detect_interrupts_are_broken = + uhci_pci_resume_detect_interrupts_are_broken; + uhci->global_suspend_mode_is_broken = + uhci_pci_global_suspend_mode_is_broken; + + + /* Kick BIOS off this hardware and reset if the controller + * isn't already safely quiescent. + */ + check_and_reset_hc(uhci); + return 0; +} + +/* Make sure the controller is quiescent and that we're not using it + * any more. This is mainly for the benefit of programs which, like kexec, + * expect the hardware to be idle: not doing DMA or generating IRQs. + * + * This routine may be called in a damaged or failing kernel. Hence we + * do not acquire the spinlock before shutting down the controller. + */ +static void uhci_shutdown(struct pci_dev *pdev) +{ + struct usb_hcd *hcd = pci_get_drvdata(pdev); + + uhci_hc_died(hcd_to_uhci(hcd)); +} + +#ifdef CONFIG_PM + +static int uhci_pci_resume(struct usb_hcd *hcd, bool hibernated); + +static int uhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) +{ + struct uhci_hcd *uhci = hcd_to_uhci(hcd); + struct pci_dev *pdev = to_pci_dev(uhci_dev(uhci)); + int rc = 0; + + dev_dbg(uhci_dev(uhci), "%s\n", __func__); + + spin_lock_irq(&uhci->lock); + if (!HCD_HW_ACCESSIBLE(hcd) || uhci->dead) + goto done_okay; /* Already suspended or dead */ + + /* All PCI host controllers are required to disable IRQ generation + * at the source, so we must turn off PIRQ. + */ + pci_write_config_word(pdev, USBLEGSUP, 0); + clear_bit(HCD_FLAG_POLL_RH, &hcd->flags); + + /* Enable platform-specific non-PME# wakeup */ + if (do_wakeup) { + if (pdev->vendor == PCI_VENDOR_ID_INTEL) + pci_write_config_byte(pdev, USBRES_INTEL, + USBPORT1EN | USBPORT2EN); + } + +done_okay: + clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + spin_unlock_irq(&uhci->lock); + + synchronize_irq(hcd->irq); + + /* Check for race with a wakeup request */ + if (do_wakeup && HCD_WAKEUP_PENDING(hcd)) { + uhci_pci_resume(hcd, false); + rc = -EBUSY; + } + return rc; +} + +static int uhci_pci_resume(struct usb_hcd *hcd, bool hibernated) +{ + struct uhci_hcd *uhci = hcd_to_uhci(hcd); + + dev_dbg(uhci_dev(uhci), "%s\n", __func__); + + /* Since we aren't in D3 any more, it's safe to set this flag + * even if the controller was dead. + */ + set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + + spin_lock_irq(&uhci->lock); + + /* Make sure resume from hibernation re-enumerates everything */ + if (hibernated) { + uhci->reset_hc(uhci); + finish_reset(uhci); + } + + /* The firmware may have changed the controller settings during + * a system wakeup. Check it and reconfigure to avoid problems. + */ + else { + check_and_reset_hc(uhci); + } + configure_hc(uhci); + + /* Tell the core if the controller had to be reset */ + if (uhci->rh_state == UHCI_RH_RESET) + usb_root_hub_lost_power(hcd->self.root_hub); + + spin_unlock_irq(&uhci->lock); + + /* If interrupts don't work and remote wakeup is enabled then + * the suspended root hub needs to be polled. + */ + if (!uhci->RD_enable && hcd->self.root_hub->do_remote_wakeup) + set_bit(HCD_FLAG_POLL_RH, &hcd->flags); + + /* Does the root hub have a port wakeup pending? */ + usb_hcd_poll_rh_status(hcd); + return 0; +} + +#endif + +static const struct hc_driver uhci_driver = { + .description = hcd_name, + .product_desc = "UHCI Host Controller", + .hcd_priv_size = sizeof(struct uhci_hcd), + + /* Generic hardware linkage */ + .irq = uhci_irq, + .flags = HCD_USB11, + + /* Basic lifecycle operations */ + .reset = uhci_pci_init, + .start = uhci_start, +#ifdef CONFIG_PM + .pci_suspend = uhci_pci_suspend, + .pci_resume = uhci_pci_resume, + .bus_suspend = uhci_rh_suspend, + .bus_resume = uhci_rh_resume, +#endif + .stop = uhci_stop, + + .urb_enqueue = uhci_urb_enqueue, + .urb_dequeue = uhci_urb_dequeue, + + .endpoint_disable = uhci_hcd_endpoint_disable, + .get_frame_number = uhci_hcd_get_frame_number, + + .hub_status_data = uhci_hub_status_data, + .hub_control = uhci_hub_control, +}; + +static const struct pci_device_id uhci_pci_ids[] = { { + /* handle any USB UHCI controller */ + PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_UHCI, ~0), + .driver_data = (unsigned long) &uhci_driver, + }, { /* end: all zeroes */ } +}; + +MODULE_DEVICE_TABLE(pci, uhci_pci_ids); + +static struct pci_driver uhci_pci_driver = { + .name = (char *)hcd_name, + .id_table = uhci_pci_ids, + + .probe = usb_hcd_pci_probe, + .remove = usb_hcd_pci_remove, + .shutdown = uhci_shutdown, + +#ifdef CONFIG_PM + .driver = { + .pm = &usb_hcd_pci_pm_ops + }, +#endif +}; + +MODULE_SOFTDEP("pre: ehci_pci"); |