diff options
Diffstat (limited to 'drivers/usb/phy')
| -rw-r--r-- | drivers/usb/phy/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/usb/phy/Makefile | 1 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-generic.c | 6 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-isp1301.c | 1 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-keystone.c | 6 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-msm-usb.c | 67 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-mxs-usb.c | 6 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-omap-otg.c | 22 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-qcom-8x16-usb.c | 436 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-tahvo.c | 27 |
10 files changed, 539 insertions, 47 deletions
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index 869c0cfca..173132416 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -152,6 +152,20 @@ config USB_MSM_OTG This driver is not supported on boards like trout which has an external PHY. +config USB_QCOM_8X16_PHY + tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support" + depends on ARCH_QCOM || COMPILE_TEST + depends on RESET_CONTROLLER && EXTCON + select USB_PHY + select USB_ULPI_VIEWPORT + help + Enable this to support the USB transceiver on Qualcomm 8x16 chipsets. + It handles PHY initialization, clock management, power management, + and workarounds required after resetting the hardware. + + To compile this driver as a module, choose M here: the + module will be called phy-qcom-8x16-usb. + config USB_MV_OTG tristate "Marvell USB OTG support" depends on USB_EHCI_MV && USB_MV_UDC && PM diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index e36ab1d46..19c0dccbb 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o obj-$(CONFIG_USB_ISP1301) += phy-isp1301.o obj-$(CONFIG_USB_MSM_OTG) += phy-msm-usb.o +obj-$(CONFIG_USB_QCOM_8X16_PHY) += phy-qcom-8x16-usb.o obj-$(CONFIG_USB_MV_OTG) += phy-mv-usb.o obj-$(CONFIG_USB_MXS_PHY) += phy-mxs-usb.o obj-$(CONFIG_USB_RCAR_PHY) += phy-rcar-usb.o diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c index 0cd85f2cc..5320cb864 100644 --- a/drivers/usb/phy/phy-generic.c +++ b/drivers/usb/phy/phy-generic.c @@ -218,11 +218,13 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop, clk_rate = 0; needs_vcc = of_property_read_bool(node, "vcc-supply"); - nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset"); + nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset", + GPIOD_ASIS); err = PTR_ERR_OR_ZERO(nop->gpiod_reset); if (!err) { nop->gpiod_vbus = devm_gpiod_get_optional(dev, - "vbus-detect"); + "vbus-detect", + GPIOD_ASIS); err = PTR_ERR_OR_ZERO(nop->gpiod_vbus); } } else if (pdata) { diff --git a/drivers/usb/phy/phy-isp1301.c b/drivers/usb/phy/phy-isp1301.c index 8a55b37d1..db6815656 100644 --- a/drivers/usb/phy/phy-isp1301.c +++ b/drivers/usb/phy/phy-isp1301.c @@ -31,6 +31,7 @@ static const struct i2c_device_id isp1301_id[] = { { "isp1301", 0 }, { } }; +MODULE_DEVICE_TABLE(i2c, isp1301_id); static struct i2c_client *isp1301_i2c_client; diff --git a/drivers/usb/phy/phy-keystone.c b/drivers/usb/phy/phy-keystone.c index e0556f783..01d4e4cdb 100644 --- a/drivers/usb/phy/phy-keystone.c +++ b/drivers/usb/phy/phy-keystone.c @@ -96,11 +96,7 @@ static int keystone_usbphy_probe(struct platform_device *pdev) platform_set_drvdata(pdev, k_phy); - ret = usb_add_phy_dev(&k_phy->usb_phy_gen.phy); - if (ret) - return ret; - - return 0; + return usb_add_phy_dev(&k_phy->usb_phy_gen.phy); } static int keystone_usbphy_remove(struct platform_device *pdev) diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c index 00c49bb1b..c58c3c0db 100644 --- a/drivers/usb/phy/phy-msm-usb.c +++ b/drivers/usb/phy/phy-msm-usb.c @@ -18,6 +18,7 @@ #include <linux/module.h> #include <linux/device.h> +#include <linux/gpio/consumer.h> #include <linux/platform_device.h> #include <linux/clk.h> #include <linux/slab.h> @@ -32,6 +33,7 @@ #include <linux/pm_runtime.h> #include <linux/of.h> #include <linux/of_device.h> +#include <linux/reboot.h> #include <linux/reset.h> #include <linux/usb.h> @@ -1471,6 +1473,14 @@ static int msm_otg_vbus_notifier(struct notifier_block *nb, unsigned long event, else clear_bit(B_SESS_VLD, &motg->inputs); + if (test_bit(B_SESS_VLD, &motg->inputs)) { + /* Switch D+/D- lines to Device connector */ + gpiod_set_value_cansleep(motg->switch_gpio, 0); + } else { + /* Switch D+/D- lines to Hub */ + gpiod_set_value_cansleep(motg->switch_gpio, 1); + } + schedule_work(&motg->sm_work); return NOTIFY_DONE; @@ -1546,6 +1556,11 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg) motg->manual_pullup = of_property_read_bool(node, "qcom,manual-pullup"); + motg->switch_gpio = devm_gpiod_get_optional(&pdev->dev, "switch", + GPIOD_OUT_LOW); + if (IS_ERR(motg->switch_gpio)) + return PTR_ERR(motg->switch_gpio); + ext_id = ERR_PTR(-ENODEV); ext_vbus = ERR_PTR(-ENODEV); if (of_property_read_bool(node, "extcon")) { @@ -1561,15 +1576,16 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg) } if (!IS_ERR(ext_vbus)) { + motg->vbus.extcon = ext_vbus; motg->vbus.nb.notifier_call = msm_otg_vbus_notifier; - ret = extcon_register_interest(&motg->vbus.conn, ext_vbus->name, - "USB", &motg->vbus.nb); + ret = extcon_register_notifier(ext_vbus, EXTCON_USB, + &motg->vbus.nb); if (ret < 0) { dev_err(&pdev->dev, "register VBUS notifier failed\n"); return ret; } - ret = extcon_get_cable_state(ext_vbus, "USB"); + ret = extcon_get_cable_state_(ext_vbus, EXTCON_USB); if (ret) set_bit(B_SESS_VLD, &motg->inputs); else @@ -1577,15 +1593,16 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg) } if (!IS_ERR(ext_id)) { + motg->id.extcon = ext_id; motg->id.nb.notifier_call = msm_otg_id_notifier; - ret = extcon_register_interest(&motg->id.conn, ext_id->name, - "USB-HOST", &motg->id.nb); + ret = extcon_register_notifier(ext_id, EXTCON_USB_HOST, + &motg->id.nb); if (ret < 0) { dev_err(&pdev->dev, "register ID notifier failed\n"); return ret; } - ret = extcon_get_cable_state(ext_id, "USB-HOST"); + ret = extcon_get_cable_state_(ext_id, EXTCON_USB_HOST); if (ret) clear_bit(ID, &motg->inputs); else @@ -1615,6 +1632,19 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg) return 0; } +static int msm_otg_reboot_notify(struct notifier_block *this, + unsigned long code, void *unused) +{ + struct msm_otg *motg = container_of(this, struct msm_otg, reboot); + + /* + * Ensure that D+/D- lines are routed to uB connector, so + * we could load bootloader/kernel at next reboot + */ + gpiod_set_value_cansleep(motg->switch_gpio, 0); + return NOTIFY_DONE; +} + static int msm_otg_probe(struct platform_device *pdev) { struct regulator_bulk_data regs[3]; @@ -1779,6 +1809,17 @@ static int msm_otg_probe(struct platform_device *pdev) dev_dbg(&pdev->dev, "Can not create mode change file\n"); } + if (test_bit(B_SESS_VLD, &motg->inputs)) { + /* Switch D+/D- lines to Device connector */ + gpiod_set_value_cansleep(motg->switch_gpio, 0); + } else { + /* Switch D+/D- lines to Hub */ + gpiod_set_value_cansleep(motg->switch_gpio, 1); + } + + motg->reboot.notifier_call = msm_otg_reboot_notify; + register_reboot_notifier(&motg->reboot); + pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); @@ -1805,10 +1846,16 @@ static int msm_otg_remove(struct platform_device *pdev) if (phy->otg->host || phy->otg->gadget) return -EBUSY; - if (motg->id.conn.edev) - extcon_unregister_interest(&motg->id.conn); - if (motg->vbus.conn.edev) - extcon_unregister_interest(&motg->vbus.conn); + unregister_reboot_notifier(&motg->reboot); + + /* + * Ensure that D+/D- lines are routed to uB connector, so + * we could load bootloader/kernel at next reboot + */ + gpiod_set_value_cansleep(motg->switch_gpio, 0); + + extcon_unregister_notifier(motg->id.extcon, EXTCON_USB_HOST, &motg->id.nb); + extcon_unregister_notifier(motg->vbus.extcon, EXTCON_USB, &motg->vbus.nb); msm_otg_debugfs_cleanup(); cancel_delayed_work_sync(&motg->chg_work); diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c index 3fcc0483a..4d863ebc1 100644 --- a/drivers/usb/phy/phy-mxs-usb.c +++ b/drivers/usb/phy/phy-mxs-usb.c @@ -506,11 +506,7 @@ static int mxs_phy_probe(struct platform_device *pdev) device_set_wakeup_capable(&pdev->dev, true); - ret = usb_add_phy_dev(&mxs_phy->phy); - if (ret) - return ret; - - return 0; + return usb_add_phy_dev(&mxs_phy->phy); } static int mxs_phy_remove(struct platform_device *pdev) diff --git a/drivers/usb/phy/phy-omap-otg.c b/drivers/usb/phy/phy-omap-otg.c index 56ee76030..c4bf2de6d 100644 --- a/drivers/usb/phy/phy-omap-otg.c +++ b/drivers/usb/phy/phy-omap-otg.c @@ -30,8 +30,7 @@ struct otg_device { void __iomem *base; bool id; bool vbus; - struct extcon_specific_cable_nb vbus_dev; - struct extcon_specific_cable_nb id_dev; + struct extcon_dev *extcon; struct notifier_block vbus_nb; struct notifier_block id_nb; }; @@ -115,23 +114,23 @@ static int omap_otg_probe(struct platform_device *pdev) if (IS_ERR(otg_dev->base)) return PTR_ERR(otg_dev->base); + otg_dev->extcon = extcon; otg_dev->id_nb.notifier_call = omap_otg_id_notifier; otg_dev->vbus_nb.notifier_call = omap_otg_vbus_notifier; - ret = extcon_register_interest(&otg_dev->id_dev, config->extcon, - "USB-HOST", &otg_dev->id_nb); + ret = extcon_register_notifier(extcon, EXTCON_USB_HOST, &otg_dev->id_nb); if (ret) return ret; - ret = extcon_register_interest(&otg_dev->vbus_dev, config->extcon, - "USB", &otg_dev->vbus_nb); + ret = extcon_register_notifier(extcon, EXTCON_USB, &otg_dev->vbus_nb); if (ret) { - extcon_unregister_interest(&otg_dev->id_dev); + extcon_unregister_notifier(extcon, EXTCON_USB_HOST, + &otg_dev->id_nb); return ret; } - otg_dev->id = extcon_get_cable_state(extcon, "USB-HOST"); - otg_dev->vbus = extcon_get_cable_state(extcon, "USB"); + otg_dev->id = extcon_get_cable_state_(extcon, EXTCON_USB_HOST); + otg_dev->vbus = extcon_get_cable_state_(extcon, EXTCON_USB); omap_otg_set_mode(otg_dev); rev = readl(otg_dev->base); @@ -147,9 +146,10 @@ static int omap_otg_probe(struct platform_device *pdev) static int omap_otg_remove(struct platform_device *pdev) { struct otg_device *otg_dev = platform_get_drvdata(pdev); + struct extcon_dev *edev = otg_dev->extcon; - extcon_unregister_interest(&otg_dev->id_dev); - extcon_unregister_interest(&otg_dev->vbus_dev); + extcon_unregister_notifier(edev, EXTCON_USB_HOST,&otg_dev->id_nb); + extcon_unregister_notifier(edev, EXTCON_USB, &otg_dev->vbus_nb); return 0; } diff --git a/drivers/usb/phy/phy-qcom-8x16-usb.c b/drivers/usb/phy/phy-qcom-8x16-usb.c new file mode 100644 index 000000000..5d357a945 --- /dev/null +++ b/drivers/usb/phy/phy-qcom-8x16-usb.c @@ -0,0 +1,436 @@ +/* + * Copyright (c) 2015, Linaro Limited + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/extcon.h> +#include <linux/gpio/consumer.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/reboot.h> +#include <linux/regulator/consumer.h> +#include <linux/reset.h> +#include <linux/slab.h> +#include <linux/usb.h> +#include <linux/usb/ulpi.h> + +#define HSPHY_AHBBURST 0x0090 +#define HSPHY_AHBMODE 0x0098 +#define HSPHY_GENCONFIG 0x009c +#define HSPHY_GENCONFIG_2 0x00a0 + +#define HSPHY_USBCMD 0x0140 +#define HSPHY_ULPI_VIEWPORT 0x0170 +#define HSPHY_CTRL 0x0240 + +#define HSPHY_TXFIFO_IDLE_FORCE_DIS BIT(4) +#define HSPHY_SESS_VLD_CTRL_EN BIT(7) +#define HSPHY_POR_ASSERT BIT(0) +#define HSPHY_RETEN BIT(1) + +#define HSPHY_SESS_VLD_CTRL BIT(25) + +#define ULPI_PWR_CLK_MNG_REG 0x88 +#define ULPI_PWR_OTG_COMP_DISABLE BIT(0) + +#define ULPI_MISC_A 0x96 +#define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1) +#define ULPI_MISC_A_VBUSVLDEXT BIT(0) + +#define HSPHY_3P3_MIN 3050000 /* uV */ +#define HSPHY_3P3_MAX 3300000 /* uV */ + +#define HSPHY_1P8_MIN 1800000 /* uV */ +#define HSPHY_1P8_MAX 1800000 /* uV */ + +#define HSPHY_VDD_MIN 5 +#define HSPHY_VDD_MAX 7 + +struct phy_8x16 { + struct usb_phy phy; + void __iomem *regs; + struct clk *core_clk; + struct clk *iface_clk; + struct regulator *v3p3; + struct regulator *v1p8; + struct regulator *vdd; + + struct reset_control *phy_reset; + + struct extcon_specific_cable_nb vbus_cable; + struct notifier_block vbus_notify; + + struct gpio_desc *switch_gpio; + struct notifier_block reboot_notify; +}; + +static int phy_8x16_regulators_enable(struct phy_8x16 *qphy) +{ + int ret; + + ret = regulator_set_voltage(qphy->vdd, HSPHY_VDD_MIN, HSPHY_VDD_MAX); + if (ret) + return ret; + + ret = regulator_enable(qphy->vdd); + if (ret) + return ret; + + ret = regulator_set_voltage(qphy->v3p3, HSPHY_3P3_MIN, HSPHY_3P3_MAX); + if (ret) + goto off_vdd; + + ret = regulator_enable(qphy->v3p3); + if (ret) + goto off_vdd; + + ret = regulator_set_voltage(qphy->v1p8, HSPHY_1P8_MIN, HSPHY_1P8_MAX); + if (ret) + goto off_3p3; + + ret = regulator_enable(qphy->v1p8); + if (ret) + goto off_3p3; + + return 0; + +off_3p3: + regulator_disable(qphy->v3p3); +off_vdd: + regulator_disable(qphy->vdd); + + return ret; +} + +static void phy_8x16_regulators_disable(struct phy_8x16 *qphy) +{ + regulator_disable(qphy->v1p8); + regulator_disable(qphy->v3p3); + regulator_disable(qphy->vdd); +} + +static int phy_8x16_notify_connect(struct usb_phy *phy, + enum usb_device_speed speed) +{ + struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy); + u32 val; + + val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT; + usb_phy_io_write(&qphy->phy, val, ULPI_SET(ULPI_MISC_A)); + + val = readl(qphy->regs + HSPHY_USBCMD); + val |= HSPHY_SESS_VLD_CTRL; + writel(val, qphy->regs + HSPHY_USBCMD); + + return 0; +} + +static int phy_8x16_notify_disconnect(struct usb_phy *phy, + enum usb_device_speed speed) +{ + struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy); + u32 val; + + val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL; + usb_phy_io_write(&qphy->phy, val, ULPI_CLR(ULPI_MISC_A)); + + val = readl(qphy->regs + HSPHY_USBCMD); + val &= ~HSPHY_SESS_VLD_CTRL; + writel(val, qphy->regs + HSPHY_USBCMD); + + return 0; +} + +static int phy_8x16_vbus_on(struct phy_8x16 *qphy) +{ + phy_8x16_notify_connect(&qphy->phy, USB_SPEED_UNKNOWN); + + /* Switch D+/D- lines to Device connector */ + gpiod_set_value_cansleep(qphy->switch_gpio, 0); + + return 0; +} + +static int phy_8x16_vbus_off(struct phy_8x16 *qphy) +{ + phy_8x16_notify_disconnect(&qphy->phy, USB_SPEED_UNKNOWN); + + /* Switch D+/D- lines to USB HUB */ + gpiod_set_value_cansleep(qphy->switch_gpio, 1); + + return 0; +} + +static int phy_8x16_vbus_notify(struct notifier_block *nb, unsigned long event, + void *ptr) +{ + struct phy_8x16 *qphy = container_of(nb, struct phy_8x16, vbus_notify); + + if (event) + phy_8x16_vbus_on(qphy); + else + phy_8x16_vbus_off(qphy); + + return NOTIFY_DONE; +} + +static int phy_8x16_init(struct usb_phy *phy) +{ + struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy); + u32 val, init[] = {0x44, 0x6B, 0x24, 0x13}; + u32 addr = ULPI_EXT_VENDOR_SPECIFIC; + int idx, state; + + for (idx = 0; idx < ARRAY_SIZE(init); idx++) + usb_phy_io_write(phy, init[idx], addr + idx); + + reset_control_reset(qphy->phy_reset); + + /* Assert USB HSPHY_POR */ + val = readl(qphy->regs + HSPHY_CTRL); + val |= HSPHY_POR_ASSERT; + writel(val, qphy->regs + HSPHY_CTRL); + + /* + * wait for minimum 10 microseconds as suggested in HPG. + * Use a slightly larger value since the exact value didn't + * work 100% of the time. + */ + usleep_range(12, 15); + + /* Deassert USB HSPHY_POR */ + val = readl(qphy->regs + HSPHY_CTRL); + val &= ~HSPHY_POR_ASSERT; + writel(val, qphy->regs + HSPHY_CTRL); + + usleep_range(10, 15); + + writel(0x00, qphy->regs + HSPHY_AHBBURST); + writel(0x08, qphy->regs + HSPHY_AHBMODE); + + /* workaround for rx buffer collision issue */ + val = readl(qphy->regs + HSPHY_GENCONFIG); + val &= ~HSPHY_TXFIFO_IDLE_FORCE_DIS; + writel(val, qphy->regs + HSPHY_GENCONFIG); + + val = readl(qphy->regs + HSPHY_GENCONFIG_2); + val |= HSPHY_SESS_VLD_CTRL_EN; + writel(val, qphy->regs + HSPHY_GENCONFIG_2); + + val = ULPI_PWR_OTG_COMP_DISABLE; + usb_phy_io_write(phy, val, ULPI_SET(ULPI_PWR_CLK_MNG_REG)); + + state = extcon_get_cable_state(qphy->vbus_cable.edev, "USB"); + if (state) + phy_8x16_vbus_on(qphy); + else + phy_8x16_vbus_off(qphy); + + val = usb_phy_io_read(&qphy->phy, ULPI_FUNC_CTRL); + val &= ~ULPI_FUNC_CTRL_OPMODE_MASK; + val |= ULPI_FUNC_CTRL_OPMODE_NORMAL; + usb_phy_io_write(&qphy->phy, val, ULPI_FUNC_CTRL); + + return 0; +} + +static void phy_8x16_shutdown(struct usb_phy *phy) +{ + u32 val; + + /* Put the controller in non-driving mode */ + val = usb_phy_io_read(phy, ULPI_FUNC_CTRL); + val &= ~ULPI_FUNC_CTRL_OPMODE_MASK; + val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING; + usb_phy_io_write(phy, val, ULPI_FUNC_CTRL); +} + +static int phy_8x16_read_devicetree(struct phy_8x16 *qphy) +{ + struct regulator_bulk_data regs[3]; + struct device *dev = qphy->phy.dev; + int ret; + + qphy->core_clk = devm_clk_get(dev, "core"); + if (IS_ERR(qphy->core_clk)) + return PTR_ERR(qphy->core_clk); + + qphy->iface_clk = devm_clk_get(dev, "iface"); + if (IS_ERR(qphy->iface_clk)) + return PTR_ERR(qphy->iface_clk); + + regs[0].supply = "v3p3"; + regs[1].supply = "v1p8"; + regs[2].supply = "vddcx"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(regs), regs); + if (ret) + return ret; + + qphy->v3p3 = regs[0].consumer; + qphy->v1p8 = regs[1].consumer; + qphy->vdd = regs[2].consumer; + + qphy->phy_reset = devm_reset_control_get(dev, "phy"); + if (IS_ERR(qphy->phy_reset)) + return PTR_ERR(qphy->phy_reset); + + qphy->switch_gpio = devm_gpiod_get_optional(dev, "switch", + GPIOD_OUT_LOW); + if (IS_ERR(qphy->switch_gpio)) + return PTR_ERR(qphy->switch_gpio); + + return 0; +} + +static int phy_8x16_reboot_notify(struct notifier_block *this, + unsigned long code, void *unused) +{ + struct phy_8x16 *qphy; + + qphy = container_of(this, struct phy_8x16, reboot_notify); + + /* + * Ensure that D+/D- lines are routed to uB connector, so + * we could load bootloader/kernel at next reboot_notify + */ + gpiod_set_value_cansleep(qphy->switch_gpio, 0); + return NOTIFY_DONE; +} + +static int phy_8x16_probe(struct platform_device *pdev) +{ + struct extcon_dev *edev; + struct phy_8x16 *qphy; + struct resource *res; + struct usb_phy *phy; + int ret; + + qphy = devm_kzalloc(&pdev->dev, sizeof(*qphy), GFP_KERNEL); + if (!qphy) + return -ENOMEM; + + platform_set_drvdata(pdev, qphy); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -EINVAL; + + qphy->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res)); + if (!qphy->regs) + return -ENOMEM; + + phy = &qphy->phy; + phy->dev = &pdev->dev; + phy->label = dev_name(&pdev->dev); + phy->init = phy_8x16_init; + phy->shutdown = phy_8x16_shutdown; + phy->notify_connect = phy_8x16_notify_connect; + phy->notify_disconnect = phy_8x16_notify_disconnect; + phy->io_priv = qphy->regs + HSPHY_ULPI_VIEWPORT; + phy->io_ops = &ulpi_viewport_access_ops; + phy->type = USB_PHY_TYPE_USB2; + + ret = phy_8x16_read_devicetree(qphy); + if (ret < 0) + return ret; + + edev = extcon_get_edev_by_phandle(phy->dev, 0); + if (IS_ERR(edev)) + return PTR_ERR(edev); + + ret = clk_set_rate(qphy->core_clk, INT_MAX); + if (ret < 0) + dev_dbg(phy->dev, "Can't boost core clock\n"); + + ret = clk_prepare_enable(qphy->core_clk); + if (ret < 0) + return ret; + + ret = clk_prepare_enable(qphy->iface_clk); + if (ret < 0) + goto off_core; + + ret = phy_8x16_regulators_enable(qphy); + if (0 && ret) + goto off_clks; + + qphy->vbus_notify.notifier_call = phy_8x16_vbus_notify; + ret = extcon_register_interest(&qphy->vbus_cable, edev->name, + "USB", &qphy->vbus_notify); + if (ret < 0) + goto off_power; + + ret = usb_add_phy_dev(&qphy->phy); + if (ret) + goto off_extcon; + + qphy->reboot_notify.notifier_call = phy_8x16_reboot_notify; + register_reboot_notifier(&qphy->reboot_notify); + + return 0; + +off_extcon: + extcon_unregister_interest(&qphy->vbus_cable); +off_power: + phy_8x16_regulators_disable(qphy); +off_clks: + clk_disable_unprepare(qphy->iface_clk); +off_core: + clk_disable_unprepare(qphy->core_clk); + return ret; +} + +static int phy_8x16_remove(struct platform_device *pdev) +{ + struct phy_8x16 *qphy = platform_get_drvdata(pdev); + + unregister_reboot_notifier(&qphy->reboot_notify); + extcon_unregister_interest(&qphy->vbus_cable); + + /* + * Ensure that D+/D- lines are routed to uB connector, so + * we could load bootloader/kernel at next reboot_notify + */ + gpiod_set_value_cansleep(qphy->switch_gpio, 0); + + usb_remove_phy(&qphy->phy); + + clk_disable_unprepare(qphy->iface_clk); + clk_disable_unprepare(qphy->core_clk); + phy_8x16_regulators_disable(qphy); + return 0; +} + +static const struct of_device_id phy_8x16_dt_match[] = { + { .compatible = "qcom,usb-8x16-phy" }, + { } +}; +MODULE_DEVICE_TABLE(of, phy_8x16_dt_match); + +static struct platform_driver phy_8x16_driver = { + .probe = phy_8x16_probe, + .remove = phy_8x16_remove, + .driver = { + .name = "phy-qcom-8x16-usb", + .of_match_table = phy_8x16_dt_match, + }, +}; +module_platform_driver(phy_8x16_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("Qualcomm APQ8016/MSM8916 chipsets USB transceiver driver"); diff --git a/drivers/usb/phy/phy-tahvo.c b/drivers/usb/phy/phy-tahvo.c index b40d6a87d..ab5d364f6 100644 --- a/drivers/usb/phy/phy-tahvo.c +++ b/drivers/usb/phy/phy-tahvo.c @@ -57,7 +57,7 @@ struct tahvo_usb { struct clk *ick; int irq; int tahvo_mode; - struct extcon_dev extcon; + struct extcon_dev *extcon; }; static const unsigned int tahvo_cable[] = { @@ -121,7 +121,7 @@ static void check_vbus_state(struct tahvo_usb *tu) prev_state = tu->vbus_state; tu->vbus_state = reg & TAHVO_STAT_VBUS; if (prev_state != tu->vbus_state) { - extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state); + extcon_set_cable_state_(tu->extcon, EXTCON_USB, tu->vbus_state); sysfs_notify(&tu->pt_dev->dev.kobj, NULL, "vbus_state"); } } @@ -130,7 +130,7 @@ static void tahvo_usb_become_host(struct tahvo_usb *tu) { struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent); - extcon_set_cable_state(&tu->extcon, "USB-HOST", true); + extcon_set_cable_state_(tu->extcon, EXTCON_USB_HOST, true); /* Power up the transceiver in USB host mode */ retu_write(rdev, TAHVO_REG_USBR, USBR_REGOUT | USBR_NSUSPEND | @@ -149,7 +149,7 @@ static void tahvo_usb_become_peripheral(struct tahvo_usb *tu) { struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent); - extcon_set_cable_state(&tu->extcon, "USB-HOST", false); + extcon_set_cable_state_(tu->extcon, EXTCON_USB_HOST, false); /* Power up transceiver and set it in USB peripheral mode */ retu_write(rdev, TAHVO_REG_USBR, USBR_SLAVE_CONTROL | USBR_REGOUT | @@ -365,11 +365,13 @@ static int tahvo_usb_probe(struct platform_device *pdev) */ tu->vbus_state = retu_read(rdev, TAHVO_REG_IDSR) & TAHVO_STAT_VBUS; - tu->extcon.name = DRIVER_NAME; - tu->extcon.supported_cable = tahvo_cable; - tu->extcon.dev.parent = &pdev->dev; + tu->extcon = devm_extcon_dev_allocate(&pdev->dev, tahvo_cable); + if (IS_ERR(tu->extcon)) { + dev_err(&pdev->dev, "failed to allocate memory for extcon\n"); + return -ENOMEM; + } - ret = extcon_dev_register(&tu->extcon); + ret = devm_extcon_dev_register(&pdev->dev, tu->extcon); if (ret) { dev_err(&pdev->dev, "could not register extcon device: %d\n", ret); @@ -377,9 +379,9 @@ static int tahvo_usb_probe(struct platform_device *pdev) } /* Set the initial cable state. */ - extcon_set_cable_state(&tu->extcon, "USB-HOST", + extcon_set_cable_state_(tu->extcon, EXTCON_USB_HOST, tu->tahvo_mode == TAHVO_MODE_HOST); - extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state); + extcon_set_cable_state_(tu->extcon, EXTCON_USB, tu->vbus_state); /* Create OTG interface */ tahvo_usb_power_off(tu); @@ -396,7 +398,7 @@ static int tahvo_usb_probe(struct platform_device *pdev) if (ret < 0) { dev_err(&pdev->dev, "cannot register USB transceiver: %d\n", ret); - goto err_extcon_unreg; + goto err_disable_clk; } dev_set_drvdata(&pdev->dev, tu); @@ -424,8 +426,6 @@ err_free_irq: free_irq(tu->irq, tu); err_remove_phy: usb_remove_phy(&tu->phy); -err_extcon_unreg: - extcon_dev_unregister(&tu->extcon); err_disable_clk: if (!IS_ERR(tu->ick)) clk_disable(tu->ick); @@ -440,7 +440,6 @@ static int tahvo_usb_remove(struct platform_device *pdev) sysfs_remove_group(&pdev->dev.kobj, &tahvo_attr_group); free_irq(tu->irq, tu); usb_remove_phy(&tu->phy); - extcon_dev_unregister(&tu->extcon); if (!IS_ERR(tu->ick)) clk_disable(tu->ick); |