diff options
Diffstat (limited to 'drivers/w1/slaves/Kconfig')
| -rw-r--r-- | drivers/w1/slaves/Kconfig | 135 |
1 files changed, 135 insertions, 0 deletions
diff --git a/drivers/w1/slaves/Kconfig b/drivers/w1/slaves/Kconfig new file mode 100644 index 000000000..cfe74d099 --- /dev/null +++ b/drivers/w1/slaves/Kconfig @@ -0,0 +1,135 @@ +# +# 1-wire slaves configuration +# + +menu "1-wire Slaves" + +config W1_SLAVE_THERM + tristate "Thermal family implementation" + help + Say Y here if you want to connect 1-wire thermal sensors to your + wire. + +config W1_SLAVE_SMEM + tristate "Simple 64bit memory family implementation" + help + Say Y here if you want to connect 1-wire + simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire. + +config W1_SLAVE_DS2408 + tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)" + help + Say Y here if you want to use a 1-wire + DS2408 8-Channel Addressable Switch device support + +config W1_SLAVE_DS2408_READBACK + bool "Read-back values written to DS2408's output register" + depends on W1_SLAVE_DS2408 + default y + help + Enabling this will cause the driver to read back the values written + to the chip's output register in order to detect errors. + + This is slower but useful when debugging chips and/or busses. + +config W1_SLAVE_DS2413 + tristate "Dual Channel Addressable Switch 0x3a family support (DS2413)" + help + Say Y here if you want to use a 1-wire + DS2413 Dual Channel Addressable Switch device support + +config W1_SLAVE_DS2406 + tristate "Dual Channel Addressable Switch 0x12 family support (DS2406)" + select CRC16 + help + Say Y or M here if you want to use a 1-wire + DS2406 Dual Channel Addressable Switch. EPROM read/write + support for these devices is not implemented. + +config W1_SLAVE_DS2423 + tristate "Counter 1-wire device (DS2423)" + select CRC16 + help + If you enable this you can read the counter values available + in the DS2423 chipset from the w1_slave file under the + sys file system. + + Say Y here if you want to use a 1-wire + counter family device (DS2423). + +config W1_SLAVE_DS2431 + tristate "1kb EEPROM family support (DS2431)" + help + Say Y here if you want to use a 1-wire + 1kb EEPROM family device (DS2431) + +config W1_SLAVE_DS2433 + tristate "4kb EEPROM family support (DS2433)" + help + Say Y here if you want to use a 1-wire + 4kb EEPROM family device (DS2433). + +config W1_SLAVE_DS2433_CRC + bool "Protect DS2433 data with a CRC16" + depends on W1_SLAVE_DS2433 + select CRC16 + help + Say Y here to protect DS2433 data with a CRC16. + Each block has 30 bytes of data and a two byte CRC16. + Full block writes are only allowed if the CRC is valid. + +config W1_SLAVE_DS2760 + tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)" + help + If you enable this you will have the DS2760 battery monitor + chip support. + + The battery monitor chip is used in many batteries/devices + as the one who is responsible for charging/discharging/monitoring + Li+ batteries. + + If you are unsure, say N. + +config W1_SLAVE_DS2780 + tristate "Dallas 2780 battery monitor chip" + help + If you enable this you will have the DS2780 battery monitor + chip support. + + The battery monitor chip is used in many batteries/devices + as the one who is responsible for charging/discharging/monitoring + Li+ batteries. + + If you are unsure, say N. + +config W1_SLAVE_DS2781 + tristate "Dallas 2781 battery monitor chip" + help + If you enable this you will have the DS2781 battery monitor + chip support. + + The battery monitor chip is used in many batteries/devices + as the one who is responsible for charging/discharging/monitoring + Li+ batteries. + + If you are unsure, say N. + +config W1_SLAVE_DS28E04 + tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)" + select CRC16 + help + If you enable this you will have the DS28E04-100 + chip support. + + Say Y here if you want to use a 1-wire + 4kb EEPROM with PIO family device (DS28E04). + + If you are unsure, say N. + +config W1_SLAVE_BQ27000 + tristate "BQ27000 slave support" + help + Say Y here if you want to use a hdq + bq27000 slave support. + +endmenu |