1 files changed, 71 insertions, 0 deletions
diff --git a/include/linux/extcon/extcon-adc-jack.h b/include/linux/extcon/extcon-adc-jack.h
new file mode 100644
index 000000000..9ca958c4e
--- /dev/null
+++ b/include/linux/extcon/extcon-adc-jack.h
@@ -0,0 +1,71 @@
+/*
+ * include/linux/extcon/extcon-adc-jack.h
+ *
+ * Analog Jack extcon driver with ADC-based detection capability.
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _EXTCON_ADC_JACK_H_
+#define _EXTCON_ADC_JACK_H_ __FILE__
+
+#include <linux/module.h>
+#include <linux/extcon.h>
+
+/**
+ * struct adc_jack_cond - condition to use an extcon state
+ * @state:		the corresponding extcon state (if 0, this struct
+ *			denotes the last adc_jack_cond element among the array)
+ * @min_adc:		min adc value for this condition
+ * @max_adc:		max adc value for this condition
+ *
+ * For example, if { .state = 0x3, .min_adc = 100, .max_adc = 200}, it means
+ * that if ADC value is between (inclusive) 100 and 200, than the cable 0 and
+ * 1 are attached (1<<0 | 1<<1 == 0x3)
+ *
+ * Note that you don't need to describe condition for "no cable attached"
+ * because when no adc_jack_cond is met, state = 0 is automatically chosen.
+ */
+struct adc_jack_cond {
+	u32 state;	/* extcon state value. 0 if invalid */
+	u32 min_adc;
+	u32 max_adc;
+};
+
+/**
+ * struct adc_jack_pdata - platform data for adc jack device.
+ * @name:		name of the extcon device. If null, "adc-jack" is used.
+ * @consumer_channel:	Unique name to identify the channel on the consumer
+ *			side. This typically describes the channels used within
+ *			the consumer. E.g. 'battery_voltage'
+ * @cable_names:	array of cable names ending with null.
+ * @adc_contitions:	array of struct adc_jack_cond conditions ending
+ *			with .state = 0 entry. This describes how to decode
+ *			adc values into extcon state.
+ * @irq_flags:		irq flags used for the @irq
+ * @handling_delay_ms:	in some devices, we need to read ADC value some
+ *			milli-seconds after the interrupt occurs. You may
+ *			describe such delays with @handling_delay_ms, which
+ *			is rounded-off by jiffies.
+ */
+struct adc_jack_pdata {
+	const char *name;
+	const char *consumer_channel;
+
+	/* The last entry should be NULL */
+	const char **cable_names;
+
+	/* The last entry's state should be 0 */
+	struct adc_jack_cond *adc_conditions;
+
+	unsigned long irq_flags;
+	unsigned long handling_delay_ms; /* in ms */
+};
+
+#endif /* _EXTCON_ADC_JACK_H */