diff options
Diffstat (limited to 'include/linux/hp_sdc.h')
| -rw-r--r-- | include/linux/hp_sdc.h | 301 |
1 files changed, 301 insertions, 0 deletions
diff --git a/include/linux/hp_sdc.h b/include/linux/hp_sdc.h new file mode 100644 index 000000000..d392975d8 --- /dev/null +++ b/include/linux/hp_sdc.h @@ -0,0 +1,301 @@ +/* + * HP i8042 System Device Controller -- header + * + * Copyright (c) 2001 Brian S. Julin + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * + * References: + * + * HP-HIL Technical Reference Manual. Hewlett Packard Product No. 45918A + * + * System Device Controller Microprocessor Firmware Theory of Operation + * for Part Number 1820-4784 Revision B. Dwg No. A-1820-4784-2 + * + */ + +#ifndef _LINUX_HP_SDC_H +#define _LINUX_HP_SDC_H + +#include <linux/interrupt.h> +#include <linux/types.h> +#include <linux/time.h> +#include <linux/timer.h> +#if defined(__hppa__) +#include <asm/hardware.h> +#endif + + +/* No 4X status reads take longer than this (in usec). + */ +#define HP_SDC_MAX_REG_DELAY 20000 + +typedef void (hp_sdc_irqhook) (int irq, void *dev_id, + uint8_t status, uint8_t data); + +int hp_sdc_request_timer_irq(hp_sdc_irqhook *callback); +int hp_sdc_request_hil_irq(hp_sdc_irqhook *callback); +int hp_sdc_request_cooked_irq(hp_sdc_irqhook *callback); +int hp_sdc_release_timer_irq(hp_sdc_irqhook *callback); +int hp_sdc_release_hil_irq(hp_sdc_irqhook *callback); +int hp_sdc_release_cooked_irq(hp_sdc_irqhook *callback); + +typedef struct { + int actidx; /* Start of act. Acts are atomic WRT I/O to SDC */ + int idx; /* Index within the act */ + int endidx; /* transaction is over and done if idx == endidx */ + uint8_t *seq; /* commands/data for the transaction */ + union { + hp_sdc_irqhook *irqhook; /* Callback, isr or tasklet context */ + struct semaphore *semaphore; /* Semaphore to sleep on. */ + } act; +} hp_sdc_transaction; +int __hp_sdc_enqueue_transaction(hp_sdc_transaction *this); +int hp_sdc_enqueue_transaction(hp_sdc_transaction *this); +int hp_sdc_dequeue_transaction(hp_sdc_transaction *this); + +/* The HP_SDC_ACT* values are peculiar to this driver. + * Nuance: never HP_SDC_ACT_DATAIN | HP_SDC_ACT_DEALLOC, use another + * act to perform the dealloc. + */ +#define HP_SDC_ACT_PRECMD 0x01 /* Send a command first */ +#define HP_SDC_ACT_DATAREG 0x02 /* Set data registers */ +#define HP_SDC_ACT_DATAOUT 0x04 /* Send data bytes */ +#define HP_SDC_ACT_POSTCMD 0x08 /* Send command after */ +#define HP_SDC_ACT_DATAIN 0x10 /* Collect data after */ +#define HP_SDC_ACT_DURING 0x1f +#define HP_SDC_ACT_SEMAPHORE 0x20 /* Raise semaphore after */ +#define HP_SDC_ACT_CALLBACK 0x40 /* Pass data to IRQ handler */ +#define HP_SDC_ACT_DEALLOC 0x80 /* Destroy transaction after */ +#define HP_SDC_ACT_AFTER 0xe0 +#define HP_SDC_ACT_DEAD 0x60 /* Act timed out. */ + +/* Rest of the flags are straightforward representation of the SDC interface */ +#define HP_SDC_STATUS_IBF 0x02 /* Input buffer full */ + +#define HP_SDC_STATUS_IRQMASK 0xf0 /* Bits containing "level 1" irq */ +#define HP_SDC_STATUS_PERIODIC 0x10 /* Periodic 10ms timer */ +#define HP_SDC_STATUS_USERTIMER 0x20 /* "Special purpose" timer */ +#define HP_SDC_STATUS_TIMER 0x30 /* Both PERIODIC and USERTIMER */ +#define HP_SDC_STATUS_REG 0x40 /* Data from an i8042 register */ +#define HP_SDC_STATUS_HILCMD 0x50 /* Command from HIL MLC */ +#define HP_SDC_STATUS_HILDATA 0x60 /* Data from HIL MLC */ +#define HP_SDC_STATUS_PUP 0x70 /* Successful power-up self test */ +#define HP_SDC_STATUS_KCOOKED 0x80 /* Key from cooked kbd */ +#define HP_SDC_STATUS_KRPG 0xc0 /* Key from Repeat Gen */ +#define HP_SDC_STATUS_KMOD_SUP 0x10 /* Shift key is up */ +#define HP_SDC_STATUS_KMOD_CUP 0x20 /* Control key is up */ + +#define HP_SDC_NMISTATUS_FHS 0x40 /* NMI is a fast handshake irq */ + +/* Internal i8042 registers (there are more, but they are not too useful). */ + +#define HP_SDC_USE 0x02 /* Resource usage (including OB bit) */ +#define HP_SDC_IM 0x04 /* Interrupt mask */ +#define HP_SDC_CFG 0x11 /* Configuration register */ +#define HP_SDC_KBLANGUAGE 0x12 /* Keyboard language */ + +#define HP_SDC_D0 0x70 /* General purpose data buffer 0 */ +#define HP_SDC_D1 0x71 /* General purpose data buffer 1 */ +#define HP_SDC_D2 0x72 /* General purpose data buffer 2 */ +#define HP_SDC_D3 0x73 /* General purpose data buffer 3 */ +#define HP_SDC_VT1 0x74 /* Timer for voice 1 */ +#define HP_SDC_VT2 0x75 /* Timer for voice 2 */ +#define HP_SDC_VT3 0x76 /* Timer for voice 3 */ +#define HP_SDC_VT4 0x77 /* Timer for voice 4 */ +#define HP_SDC_KBN 0x78 /* Which HIL devs are Nimitz */ +#define HP_SDC_KBC 0x79 /* Which HIL devs are cooked kbds */ +#define HP_SDC_LPS 0x7a /* i8042's view of HIL status */ +#define HP_SDC_LPC 0x7b /* i8042's view of HIL "control" */ +#define HP_SDC_RSV 0x7c /* Reserved "for testing" */ +#define HP_SDC_LPR 0x7d /* i8042 count of HIL reconfigs */ +#define HP_SDC_XTD 0x7e /* "Extended Configuration" register */ +#define HP_SDC_STR 0x7f /* i8042 self-test result */ + +/* Bitfields for above registers */ +#define HP_SDC_USE_LOOP 0x04 /* Command is currently on the loop. */ + +#define HP_SDC_IM_MASK 0x1f /* these bits not part of cmd/status */ +#define HP_SDC_IM_FH 0x10 /* Mask the fast handshake irq */ +#define HP_SDC_IM_PT 0x08 /* Mask the periodic timer irq */ +#define HP_SDC_IM_TIMERS 0x04 /* Mask the MT/DT/CT irq */ +#define HP_SDC_IM_RESET 0x02 /* Mask the reset key irq */ +#define HP_SDC_IM_HIL 0x01 /* Mask the HIL MLC irq */ + +#define HP_SDC_CFG_ROLLOVER 0x08 /* WTF is "N-key rollover"? */ +#define HP_SDC_CFG_KBD 0x10 /* There is a keyboard */ +#define HP_SDC_CFG_NEW 0x20 /* Supports/uses HIL MLC */ +#define HP_SDC_CFG_KBD_OLD 0x03 /* keyboard code for non-HIL */ +#define HP_SDC_CFG_KBD_NEW 0x07 /* keyboard code from HIL autoconfig */ +#define HP_SDC_CFG_REV 0x40 /* Code revision bit */ +#define HP_SDC_CFG_IDPROM 0x80 /* IDPROM present in kbd (not HIL) */ + +#define HP_SDC_LPS_NDEV 0x07 /* # devices autoconfigured on HIL */ +#define HP_SDC_LPS_ACSUCC 0x08 /* loop autoconfigured successfully */ +#define HP_SDC_LPS_ACFAIL 0x80 /* last loop autoconfigure failed */ + +#define HP_SDC_LPC_APE_IPF 0x01 /* HIL MLC APE/IPF (autopoll) set */ +#define HP_SDC_LPC_ARCONERR 0x02 /* i8042 autoreconfigs loop on err */ +#define HP_SDC_LPC_ARCQUIET 0x03 /* i8042 doesn't report autoreconfigs*/ +#define HP_SDC_LPC_COOK 0x10 /* i8042 cooks devices in _KBN */ +#define HP_SDC_LPC_RC 0x80 /* causes autoreconfig */ + +#define HP_SDC_XTD_REV 0x07 /* contains revision code */ +#define HP_SDC_XTD_REV_STRINGS(val, str) \ +switch (val) { \ + case 0x1: str = "1820-3712"; break; \ + case 0x2: str = "1820-4379"; break; \ + case 0x3: str = "1820-4784"; break; \ + default: str = "unknown"; \ +}; +#define HP_SDC_XTD_BEEPER 0x08 /* TI SN76494 beeper available */ +#define HP_SDC_XTD_BBRTC 0x20 /* OKI MSM-58321 BBRTC present */ + +#define HP_SDC_CMD_LOAD_RT 0x31 /* Load real time (from 8042) */ +#define HP_SDC_CMD_LOAD_FHS 0x36 /* Load the fast handshake timer */ +#define HP_SDC_CMD_LOAD_MT 0x38 /* Load the match timer */ +#define HP_SDC_CMD_LOAD_DT 0x3B /* Load the delay timer */ +#define HP_SDC_CMD_LOAD_CT 0x3E /* Load the cycle timer */ + +#define HP_SDC_CMD_SET_IM 0x40 /* 010xxxxx == set irq mask */ + +/* The documents provided do not explicitly state that all registers betweem + * 0x01 and 0x1f inclusive can be read by sending their register index as a + * command, but this is implied and appears to be the case. + */ +#define HP_SDC_CMD_READ_RAM 0x00 /* Load from i8042 RAM (autoinc) */ +#define HP_SDC_CMD_READ_USE 0x02 /* Undocumented! Load from usage reg */ +#define HP_SDC_CMD_READ_IM 0x04 /* Load current interrupt mask */ +#define HP_SDC_CMD_READ_KCC 0x11 /* Load primary kbd config code */ +#define HP_SDC_CMD_READ_KLC 0x12 /* Load primary kbd language code */ +#define HP_SDC_CMD_READ_T1 0x13 /* Load timer output buffer byte 1 */ +#define HP_SDC_CMD_READ_T2 0x14 /* Load timer output buffer byte 1 */ +#define HP_SDC_CMD_READ_T3 0x15 /* Load timer output buffer byte 1 */ +#define HP_SDC_CMD_READ_T4 0x16 /* Load timer output buffer byte 1 */ +#define HP_SDC_CMD_READ_T5 0x17 /* Load timer output buffer byte 1 */ +#define HP_SDC_CMD_READ_D0 0xf0 /* Load from i8042 RAM location 0x70 */ +#define HP_SDC_CMD_READ_D1 0xf1 /* Load from i8042 RAM location 0x71 */ +#define HP_SDC_CMD_READ_D2 0xf2 /* Load from i8042 RAM location 0x72 */ +#define HP_SDC_CMD_READ_D3 0xf3 /* Load from i8042 RAM location 0x73 */ +#define HP_SDC_CMD_READ_VT1 0xf4 /* Load from i8042 RAM location 0x74 */ +#define HP_SDC_CMD_READ_VT2 0xf5 /* Load from i8042 RAM location 0x75 */ +#define HP_SDC_CMD_READ_VT3 0xf6 /* Load from i8042 RAM location 0x76 */ +#define HP_SDC_CMD_READ_VT4 0xf7 /* Load from i8042 RAM location 0x77 */ +#define HP_SDC_CMD_READ_KBN 0xf8 /* Load from i8042 RAM location 0x78 */ +#define HP_SDC_CMD_READ_KBC 0xf9 /* Load from i8042 RAM location 0x79 */ +#define HP_SDC_CMD_READ_LPS 0xfa /* Load from i8042 RAM location 0x7a */ +#define HP_SDC_CMD_READ_LPC 0xfb /* Load from i8042 RAM location 0x7b */ +#define HP_SDC_CMD_READ_RSV 0xfc /* Load from i8042 RAM location 0x7c */ +#define HP_SDC_CMD_READ_LPR 0xfd /* Load from i8042 RAM location 0x7d */ +#define HP_SDC_CMD_READ_XTD 0xfe /* Load from i8042 RAM location 0x7e */ +#define HP_SDC_CMD_READ_STR 0xff /* Load from i8042 RAM location 0x7f */ + +#define HP_SDC_CMD_SET_ARD 0xA0 /* Set emulated autorepeat delay */ +#define HP_SDC_CMD_SET_ARR 0xA2 /* Set emulated autorepeat rate */ +#define HP_SDC_CMD_SET_BELL 0xA3 /* Set voice 3 params for "beep" cmd */ +#define HP_SDC_CMD_SET_RPGR 0xA6 /* Set "RPG" irq rate (doesn't work) */ +#define HP_SDC_CMD_SET_RTMS 0xAD /* Set the RTC time (milliseconds) */ +#define HP_SDC_CMD_SET_RTD 0xAF /* Set the RTC time (days) */ +#define HP_SDC_CMD_SET_FHS 0xB2 /* Set fast handshake timer */ +#define HP_SDC_CMD_SET_MT 0xB4 /* Set match timer */ +#define HP_SDC_CMD_SET_DT 0xB7 /* Set delay timer */ +#define HP_SDC_CMD_SET_CT 0xBA /* Set cycle timer */ +#define HP_SDC_CMD_SET_RAMP 0xC1 /* Reset READ_RAM autoinc counter */ +#define HP_SDC_CMD_SET_D0 0xe0 /* Load to i8042 RAM location 0x70 */ +#define HP_SDC_CMD_SET_D1 0xe1 /* Load to i8042 RAM location 0x71 */ +#define HP_SDC_CMD_SET_D2 0xe2 /* Load to i8042 RAM location 0x72 */ +#define HP_SDC_CMD_SET_D3 0xe3 /* Load to i8042 RAM location 0x73 */ +#define HP_SDC_CMD_SET_VT1 0xe4 /* Load to i8042 RAM location 0x74 */ +#define HP_SDC_CMD_SET_VT2 0xe5 /* Load to i8042 RAM location 0x75 */ +#define HP_SDC_CMD_SET_VT3 0xe6 /* Load to i8042 RAM location 0x76 */ +#define HP_SDC_CMD_SET_VT4 0xe7 /* Load to i8042 RAM location 0x77 */ +#define HP_SDC_CMD_SET_KBN 0xe8 /* Load to i8042 RAM location 0x78 */ +#define HP_SDC_CMD_SET_KBC 0xe9 /* Load to i8042 RAM location 0x79 */ +#define HP_SDC_CMD_SET_LPS 0xea /* Load to i8042 RAM location 0x7a */ +#define HP_SDC_CMD_SET_LPC 0xeb /* Load to i8042 RAM location 0x7b */ +#define HP_SDC_CMD_SET_RSV 0xec /* Load to i8042 RAM location 0x7c */ +#define HP_SDC_CMD_SET_LPR 0xed /* Load to i8042 RAM location 0x7d */ +#define HP_SDC_CMD_SET_XTD 0xee /* Load to i8042 RAM location 0x7e */ +#define HP_SDC_CMD_SET_STR 0xef /* Load to i8042 RAM location 0x7f */ + +#define HP_SDC_CMD_DO_RTCW 0xc2 /* i8042 RAM 0x70 --> RTC */ +#define HP_SDC_CMD_DO_RTCR 0xc3 /* RTC[0x70 0:3] --> irq/status/data */ +#define HP_SDC_CMD_DO_BEEP 0xc4 /* i8042 RAM 0x70-74 --> beeper,VT3 */ +#define HP_SDC_CMD_DO_HIL 0xc5 /* i8042 RAM 0x70-73 --> + HIL MLC R0,R1 i8042 HIL watchdog */ + +/* Values used to (de)mangle input/output to/from the HIL MLC */ +#define HP_SDC_DATA 0x40 /* Data from an 8042 register */ +#define HP_SDC_HIL_CMD 0x50 /* Data from HIL MLC R1/8042 */ +#define HP_SDC_HIL_R1MASK 0x0f /* Contents of HIL MLC R1 0:3 */ +#define HP_SDC_HIL_AUTO 0x10 /* Set if POL results from i8042 */ +#define HP_SDC_HIL_ISERR 0x80 /* Has meaning as in next 4 values */ +#define HP_SDC_HIL_RC_DONE 0x80 /* i8042 auto-configured loop */ +#define HP_SDC_HIL_ERR 0x81 /* HIL MLC R2 had a bit set */ +#define HP_SDC_HIL_TO 0x82 /* i8042 HIL watchdog expired */ +#define HP_SDC_HIL_RC 0x84 /* i8042 is auto-configuring loop */ +#define HP_SDC_HIL_DAT 0x60 /* Data from HIL MLC R0 */ + + +typedef struct { + rwlock_t ibf_lock; + rwlock_t lock; /* user/tasklet lock */ + rwlock_t rtq_lock; /* isr/tasklet lock */ + rwlock_t hook_lock; /* isr/user lock for handler add/del */ + + unsigned int irq, nmi; /* Our IRQ lines */ + unsigned long base_io, status_io, data_io; /* Our IO ports */ + + uint8_t im; /* Interrupt mask */ + int set_im; /* Interrupt mask needs to be set. */ + + int ibf; /* Last known status of IBF flag */ + uint8_t wi; /* current i8042 write index */ + uint8_t r7[4]; /* current i8042[0x70 - 0x74] values */ + uint8_t r11, r7e; /* Values from version/revision regs */ + + hp_sdc_irqhook *timer, *reg, *hil, *pup, *cooked; + +#define HP_SDC_QUEUE_LEN 16 + hp_sdc_transaction *tq[HP_SDC_QUEUE_LEN]; /* All pending read/writes */ + + int rcurr, rqty; /* Current read transact in process */ + struct timeval rtv; /* Time when current read started */ + int wcurr; /* Current write transact in process */ + + int dev_err; /* carries status from registration */ +#if defined(__hppa__) + struct parisc_device *dev; +#elif defined(__mc68000__) + void *dev; +#else +#error No support for device registration on this arch yet. +#endif + + struct timer_list kicker; /* Keeps below task alive */ + struct tasklet_struct task; + +} hp_i8042_sdc; + +#endif /* _LINUX_HP_SDC_H */ |