diff options
Diffstat (limited to 'include/linux/iio/frequency/ad9523.h')
| -rw-r--r-- | include/linux/iio/frequency/ad9523.h | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/include/linux/iio/frequency/ad9523.h b/include/linux/iio/frequency/ad9523.h new file mode 100644 index 000000000..12ce3ee42 --- /dev/null +++ b/include/linux/iio/frequency/ad9523.h @@ -0,0 +1,195 @@ +/* + * AD9523 SPI Low Jitter Clock Generator + * + * Copyright 2012 Analog Devices Inc. + * + * Licensed under the GPL-2. + */ + +#ifndef IIO_FREQUENCY_AD9523_H_ +#define IIO_FREQUENCY_AD9523_H_ + +enum outp_drv_mode { + TRISTATE, + LVPECL_8mA, + LVDS_4mA, + LVDS_7mA, + HSTL0_16mA, + HSTL1_8mA, + CMOS_CONF1, + CMOS_CONF2, + CMOS_CONF3, + CMOS_CONF4, + CMOS_CONF5, + CMOS_CONF6, + CMOS_CONF7, + CMOS_CONF8, + CMOS_CONF9 +}; + +enum ref_sel_mode { + NONEREVERTIVE_STAY_ON_REFB, + REVERT_TO_REFA, + SELECT_REFA, + SELECT_REFB, + EXT_REF_SEL +}; + +/** + * struct ad9523_channel_spec - Output channel configuration + * + * @channel_num: Output channel number. + * @divider_output_invert_en: Invert the polarity of the output clock. + * @sync_ignore_en: Ignore chip-level SYNC signal. + * @low_power_mode_en: Reduce power used in the differential output modes. + * @use_alt_clock_src: Channel divider uses alternative clk source. + * @output_dis: Disables, powers down the entire channel. + * @driver_mode: Output driver mode (logic level family). + * @divider_phase: Divider initial phase after a SYNC. Range 0..63 + LSB = 1/2 of a period of the divider input clock. + * @channel_divider: 10-bit channel divider. + * @extended_name: Optional descriptive channel name. + */ + +struct ad9523_channel_spec { + unsigned channel_num; + bool divider_output_invert_en; + bool sync_ignore_en; + bool low_power_mode_en; + /* CH0..CH3 VCXO, CH4..CH9 VCO2 */ + bool use_alt_clock_src; + bool output_dis; + enum outp_drv_mode driver_mode; + unsigned char divider_phase; + unsigned short channel_divider; + char extended_name[16]; +}; + +enum pll1_rzero_resistor { + RZERO_883_OHM, + RZERO_677_OHM, + RZERO_341_OHM, + RZERO_135_OHM, + RZERO_10_OHM, + RZERO_USE_EXT_RES = 8, +}; + +enum rpole2_resistor { + RPOLE2_900_OHM, + RPOLE2_450_OHM, + RPOLE2_300_OHM, + RPOLE2_225_OHM, +}; + +enum rzero_resistor { + RZERO_3250_OHM, + RZERO_2750_OHM, + RZERO_2250_OHM, + RZERO_2100_OHM, + RZERO_3000_OHM, + RZERO_2500_OHM, + RZERO_2000_OHM, + RZERO_1850_OHM, +}; + +enum cpole1_capacitor { + CPOLE1_0_PF, + CPOLE1_8_PF, + CPOLE1_16_PF, + CPOLE1_24_PF, + _CPOLE1_24_PF, /* place holder */ + CPOLE1_32_PF, + CPOLE1_40_PF, + CPOLE1_48_PF, +}; + +/** + * struct ad9523_platform_data - platform specific information + * + * @vcxo_freq: External VCXO frequency in Hz + * @refa_diff_rcv_en: REFA differential/single-ended input selection. + * @refb_diff_rcv_en: REFB differential/single-ended input selection. + * @zd_in_diff_en: Zero Delay differential/single-ended input selection. + * @osc_in_diff_en: OSC differential/ single-ended input selection. + * @refa_cmos_neg_inp_en: REFA single-ended neg./pos. input enable. + * @refb_cmos_neg_inp_en: REFB single-ended neg./pos. input enable. + * @zd_in_cmos_neg_inp_en: Zero Delay single-ended neg./pos. input enable. + * @osc_in_cmos_neg_inp_en: OSC single-ended neg./pos. input enable. + * @refa_r_div: PLL1 10-bit REFA R divider. + * @refb_r_div: PLL1 10-bit REFB R divider. + * @pll1_feedback_div: PLL1 10-bit Feedback N divider. + * @pll1_charge_pump_current_nA: Magnitude of PLL1 charge pump current (nA). + * @zero_delay_mode_internal_en: Internal, external Zero Delay mode selection. + * @osc_in_feedback_en: PLL1 feedback path, local feedback from + * the OSC_IN receiver or zero delay mode + * @pll1_loop_filter_rzero: PLL1 Loop Filter Zero Resistor selection. + * @ref_mode: Reference selection mode. + * @pll2_charge_pump_current_nA: Magnitude of PLL2 charge pump current (nA). + * @pll2_ndiv_a_cnt: PLL2 Feedback N-divider, A Counter, range 0..4. + * @pll2_ndiv_b_cnt: PLL2 Feedback N-divider, B Counter, range 0..63. + * @pll2_freq_doubler_en: PLL2 frequency doubler enable. + * @pll2_r2_div: PLL2 R2 divider, range 0..31. + * @pll2_vco_diff_m1: VCO1 divider, range 3..5. + * @pll2_vco_diff_m2: VCO2 divider, range 3..5. + * @rpole2: PLL2 loop filter Rpole resistor value. + * @rzero: PLL2 loop filter Rzero resistor value. + * @cpole1: PLL2 loop filter Cpole capacitor value. + * @rzero_bypass_en: PLL2 loop filter Rzero bypass enable. + * @num_channels: Array size of struct ad9523_channel_spec. + * @channels: Pointer to channel array. + * @name: Optional alternative iio device name. + */ + +struct ad9523_platform_data { + unsigned long vcxo_freq; + + /* Differential/ Single-Ended Input Configuration */ + bool refa_diff_rcv_en; + bool refb_diff_rcv_en; + bool zd_in_diff_en; + bool osc_in_diff_en; + + /* + * Valid if differential input disabled + * if false defaults to pos input + */ + bool refa_cmos_neg_inp_en; + bool refb_cmos_neg_inp_en; + bool zd_in_cmos_neg_inp_en; + bool osc_in_cmos_neg_inp_en; + + /* PLL1 Setting */ + unsigned short refa_r_div; + unsigned short refb_r_div; + unsigned short pll1_feedback_div; + unsigned short pll1_charge_pump_current_nA; + bool zero_delay_mode_internal_en; + bool osc_in_feedback_en; + enum pll1_rzero_resistor pll1_loop_filter_rzero; + + /* Reference */ + enum ref_sel_mode ref_mode; + + /* PLL2 Setting */ + unsigned int pll2_charge_pump_current_nA; + unsigned char pll2_ndiv_a_cnt; + unsigned char pll2_ndiv_b_cnt; + bool pll2_freq_doubler_en; + unsigned char pll2_r2_div; + unsigned char pll2_vco_diff_m1; /* 3..5 */ + unsigned char pll2_vco_diff_m2; /* 3..5 */ + + /* Loop Filter PLL2 */ + enum rpole2_resistor rpole2; + enum rzero_resistor rzero; + enum cpole1_capacitor cpole1; + bool rzero_bypass_en; + + /* Output Channel Configuration */ + int num_channels; + struct ad9523_channel_spec *channels; + + char name[SPI_NAME_SIZE]; +}; + +#endif /* IIO_FREQUENCY_AD9523_H_ */ |