diff options
Diffstat (limited to 'include/linux/mtd/fsmc.h')
| -rw-r--r-- | include/linux/mtd/fsmc.h | 174 |
1 files changed, 174 insertions, 0 deletions
diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h new file mode 100644 index 000000000..c8be32e9f --- /dev/null +++ b/include/linux/mtd/fsmc.h @@ -0,0 +1,174 @@ +/* + * incude/mtd/fsmc.h + * + * ST Microelectronics + * Flexible Static Memory Controller (FSMC) + * platform data interface and header file + * + * Copyright © 2010 ST Microelectronics + * Vipin Kumar <vipin.kumar@st.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __MTD_FSMC_H +#define __MTD_FSMC_H + +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/mtd/physmap.h> +#include <linux/types.h> +#include <linux/mtd/partitions.h> +#include <asm/param.h> + +#define FSMC_NAND_BW8 1 +#define FSMC_NAND_BW16 2 + +#define FSMC_MAX_NOR_BANKS 4 +#define FSMC_MAX_NAND_BANKS 4 + +#define FSMC_FLASH_WIDTH8 1 +#define FSMC_FLASH_WIDTH16 2 + +/* fsmc controller registers for NOR flash */ +#define CTRL 0x0 + /* ctrl register definitions */ + #define BANK_ENABLE (1 << 0) + #define MUXED (1 << 1) + #define NOR_DEV (2 << 2) + #define WIDTH_8 (0 << 4) + #define WIDTH_16 (1 << 4) + #define RSTPWRDWN (1 << 6) + #define WPROT (1 << 7) + #define WRT_ENABLE (1 << 12) + #define WAIT_ENB (1 << 13) + +#define CTRL_TIM 0x4 + /* ctrl_tim register definitions */ + +#define FSMC_NOR_BANK_SZ 0x8 +#define FSMC_NOR_REG_SIZE 0x40 + +#define FSMC_NOR_REG(base, bank, reg) (base + \ + FSMC_NOR_BANK_SZ * (bank) + \ + reg) + +/* fsmc controller registers for NAND flash */ +#define PC 0x00 + /* pc register definitions */ + #define FSMC_RESET (1 << 0) + #define FSMC_WAITON (1 << 1) + #define FSMC_ENABLE (1 << 2) + #define FSMC_DEVTYPE_NAND (1 << 3) + #define FSMC_DEVWID_8 (0 << 4) + #define FSMC_DEVWID_16 (1 << 4) + #define FSMC_ECCEN (1 << 6) + #define FSMC_ECCPLEN_512 (0 << 7) + #define FSMC_ECCPLEN_256 (1 << 7) + #define FSMC_TCLR_1 (1) + #define FSMC_TCLR_SHIFT (9) + #define FSMC_TCLR_MASK (0xF) + #define FSMC_TAR_1 (1) + #define FSMC_TAR_SHIFT (13) + #define FSMC_TAR_MASK (0xF) +#define STS 0x04 + /* sts register definitions */ + #define FSMC_CODE_RDY (1 << 15) +#define COMM 0x08 + /* comm register definitions */ + #define FSMC_TSET_0 0 + #define FSMC_TSET_SHIFT 0 + #define FSMC_TSET_MASK 0xFF + #define FSMC_TWAIT_6 6 + #define FSMC_TWAIT_SHIFT 8 + #define FSMC_TWAIT_MASK 0xFF + #define FSMC_THOLD_4 4 + #define FSMC_THOLD_SHIFT 16 + #define FSMC_THOLD_MASK 0xFF + #define FSMC_THIZ_1 1 + #define FSMC_THIZ_SHIFT 24 + #define FSMC_THIZ_MASK 0xFF +#define ATTRIB 0x0C +#define IOATA 0x10 +#define ECC1 0x14 +#define ECC2 0x18 +#define ECC3 0x1C +#define FSMC_NAND_BANK_SZ 0x20 + +#define FSMC_NAND_REG(base, bank, reg) (base + FSMC_NOR_REG_SIZE + \ + (FSMC_NAND_BANK_SZ * (bank)) + \ + reg) + +#define FSMC_BUSY_WAIT_TIMEOUT (1 * HZ) + +/* + * There are 13 bytes of ecc for every 512 byte block in FSMC version 8 + * and it has to be read consecutively and immediately after the 512 + * byte data block for hardware to generate the error bit offsets + * Managing the ecc bytes in the following way is easier. This way is + * similar to oobfree structure maintained already in u-boot nand driver + */ +#define MAX_ECCPLACE_ENTRIES 32 + +struct fsmc_nand_eccplace { + uint8_t offset; + uint8_t length; +}; + +struct fsmc_eccplace { + struct fsmc_nand_eccplace eccplace[MAX_ECCPLACE_ENTRIES]; +}; + +struct fsmc_nand_timings { + uint8_t tclr; + uint8_t tar; + uint8_t thiz; + uint8_t thold; + uint8_t twait; + uint8_t tset; +}; + +enum access_mode { + USE_DMA_ACCESS = 1, + USE_WORD_ACCESS, +}; + +/** + * fsmc_nand_platform_data - platform specific NAND controller config + * @nand_timings: timing setup for the physical NAND interface + * @partitions: partition table for the platform, use a default fallback + * if this is NULL + * @nr_partitions: the number of partitions in the previous entry + * @options: different options for the driver + * @width: bus width + * @bank: default bank + * @select_bank: callback to select a certain bank, this is + * platform-specific. If the controller only supports one bank + * this may be set to NULL + */ +struct fsmc_nand_platform_data { + struct fsmc_nand_timings *nand_timings; + struct mtd_partition *partitions; + unsigned int nr_partitions; + unsigned int options; + unsigned int width; + unsigned int bank; + + enum access_mode mode; + + void (*select_bank)(uint32_t bank, uint32_t busw); + + /* priv structures for dma accesses */ + void *read_dma_priv; + void *write_dma_priv; +}; + +extern int __init fsmc_nor_init(struct platform_device *pdev, + unsigned long base, uint32_t bank, uint32_t width); +extern void __init fsmc_init_board_info(struct platform_device *pdev, + struct mtd_partition *partitions, unsigned int nr_partitions, + unsigned int width); + +#endif /* __MTD_FSMC_H */ |