diff options
Diffstat (limited to 'include/linux/power/smb347-charger.h')
| -rw-r--r-- | include/linux/power/smb347-charger.h | 117 |
1 files changed, 117 insertions, 0 deletions
diff --git a/include/linux/power/smb347-charger.h b/include/linux/power/smb347-charger.h new file mode 100644 index 000000000..b3cb20dab --- /dev/null +++ b/include/linux/power/smb347-charger.h @@ -0,0 +1,117 @@ +/* + * Summit Microelectronics SMB347 Battery Charger Driver + * + * Copyright (C) 2011, Intel Corporation + * + * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com> + * Mika Westerberg <mika.westerberg@linux.intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef SMB347_CHARGER_H +#define SMB347_CHARGER_H + +#include <linux/types.h> +#include <linux/power_supply.h> + +enum { + /* use the default compensation method */ + SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1, + + SMB347_SOFT_TEMP_COMPENSATE_NONE, + SMB347_SOFT_TEMP_COMPENSATE_CURRENT, + SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE, +}; + +/* Use default factory programmed value for hard/soft temperature limit */ +#define SMB347_TEMP_USE_DEFAULT -273 + +/* + * Charging enable can be controlled by software (via i2c) by + * smb347-charger driver or by EN pin (active low/high). + */ +enum smb347_chg_enable { + SMB347_CHG_ENABLE_SW, + SMB347_CHG_ENABLE_PIN_ACTIVE_LOW, + SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH, +}; + +/** + * struct smb347_charger_platform_data - platform data for SMB347 charger + * @battery_info: Information about the battery + * @max_charge_current: maximum current (in uA) the battery can be charged + * @max_charge_voltage: maximum voltage (in uV) the battery can be charged + * @pre_charge_current: current (in uA) to use in pre-charging phase + * @termination_current: current (in uA) used to determine when the + * charging cycle terminates + * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to + * pre-charge to fast charge mode + * @mains_current_limit: maximum input current drawn from AC/DC input (in uA) + * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB + * input + * @chip_temp_threshold: die temperature where device starts limiting charge + * current [%100 - %130] (in degree C) + * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C), + * granularity is 5 deg C. + * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C), + * granularity is 5 deg C. + * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C), + * granularity is 5 deg C. + * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C), + * granularity is 5 deg C. + * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit + * @soft_temp_limit_compensation: compensation method when soft temperature + * limit is hit + * @charge_current_compensation: current (in uA) for charging compensation + * current when temperature hits soft limits + * @use_mains: AC/DC input can be used + * @use_usb: USB input can be used + * @use_usb_otg: USB OTG output can be used (not implemented yet) + * @irq_gpio: GPIO number used for interrupts (%-1 if not used) + * @enable_control: how charging enable/disable is controlled + * (driver/pin controls) + * + * @use_main, @use_usb, and @use_usb_otg are means to enable/disable + * hardware support for these. This is useful when we want to have for + * example OTG charging controlled via OTG transceiver driver and not by + * the SMB347 hardware. + * + * Hard and soft temperature limit values are given as described in the + * device data sheet and assuming NTC beta value is %3750. Even if this is + * not the case, these values should be used. They can be mapped to the + * corresponding NTC beta values with the help of table %2 in the data + * sheet. So for example if NTC beta is %3375 and we want to program hard + * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50. + * + * If zero value is given in any of the current and voltage values, the + * factory programmed default will be used. For soft/hard temperature + * values, pass in %SMB347_TEMP_USE_DEFAULT instead. + */ +struct smb347_charger_platform_data { + struct power_supply_info battery_info; + unsigned int max_charge_current; + unsigned int max_charge_voltage; + unsigned int pre_charge_current; + unsigned int termination_current; + unsigned int pre_to_fast_voltage; + unsigned int mains_current_limit; + unsigned int usb_hc_current_limit; + unsigned int chip_temp_threshold; + int soft_cold_temp_limit; + int soft_hot_temp_limit; + int hard_cold_temp_limit; + int hard_hot_temp_limit; + bool suspend_on_hard_temp_limit; + unsigned int soft_temp_limit_compensation; + unsigned int charge_current_compensation; + bool use_mains; + bool use_usb; + bool use_usb_otg; + int irq_gpio; + enum smb347_chg_enable enable_control; +}; + +#endif /* SMB347_CHARGER_H */ |