diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 73 |
1 files changed, 39 insertions, 34 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 6b1077c2a..bfc569498 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -477,7 +477,9 @@ struct ieee80211_event { * @chandef: Channel definition for this BSS -- the hardware might be * configured a higher bandwidth than this BSS uses, for example. * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation. - * This field is only valid when the channel type is one of the HT types. + * This field is only valid when the channel is a wide HT/VHT channel. + * Note that with TDLS this can be the case (channel is HT, protection must + * be used from this field) even when the BSS association isn't using HT. * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value * implies disabled * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis @@ -973,6 +975,10 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. * If this flag is set, the stack cannot do any replay detection * hence the driver or hardware will have to do that. + * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this + * flag indicates that the PN was verified for replay protection. + * Note that this flag is also currently only supported when a frame + * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set) * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on * the frame. * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on @@ -997,9 +1003,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference * number (@ampdu_reference) must be populated and be a distinct number for * each A-MPDU - * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes - * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for - * monitoring purposes only * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all * subframes of a single A-MPDU * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU @@ -1039,8 +1042,8 @@ enum mac80211_rx_flags { RX_FLAG_NO_SIGNAL_VAL = BIT(12), RX_FLAG_HT_GF = BIT(13), RX_FLAG_AMPDU_DETAILS = BIT(14), - RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15), - RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16), + RX_FLAG_PN_VALIDATED = BIT(15), + /* bit 16 free */ RX_FLAG_AMPDU_LAST_KNOWN = BIT(17), RX_FLAG_AMPDU_IS_LAST = BIT(18), RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19), @@ -1491,8 +1494,10 @@ enum ieee80211_key_flags { * - Temporal Authenticator Rx MIC Key (64 bits) * @icv_len: The ICV length for this key type * @iv_len: The IV length for this key type + * @drv_priv: pointer for driver use */ struct ieee80211_key_conf { + void *drv_priv; atomic64_t tx_pn; u32 cipher; u8 icv_len; @@ -1675,7 +1680,6 @@ struct ieee80211_sta_rates { * @tdls: indicates whether the STA is a TDLS peer * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only * valid if the STA is a TDLS peer in the first place. - * @mfp: indicates whether the STA uses management frame protection or not. * @txq: per-TID data TX queues (if driver uses the TXQ abstraction) */ struct ieee80211_sta { @@ -1693,7 +1697,6 @@ struct ieee80211_sta { struct ieee80211_sta_rates __rcu *rates; bool tdls; bool tdls_initiator; - bool mfp; struct ieee80211_txq *txq[IEEE80211_NUM_TIDS]; @@ -1888,6 +1891,9 @@ struct ieee80211_txq { * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands * in one command, mac80211 doesn't have to run separate scans per band. * + * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth + * than then BSS bandwidth for a TDLS link on the base channel. + * * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays */ enum ieee80211_hw_flags { @@ -1920,6 +1926,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_CHANCTX_STA_CSA, IEEE80211_HW_SUPPORTS_CLONED_SKBS, IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS, + IEEE80211_HW_TDLS_WIDER_BW, /* keep last, obviously */ NUM_IEEE80211_HW_FLAGS @@ -3696,20 +3703,28 @@ void ieee80211_free_hw(struct ieee80211_hw *hw); void ieee80211_restart_hw(struct ieee80211_hw *hw); /** - * ieee80211_napi_add - initialize mac80211 NAPI context - * @hw: the hardware to initialize the NAPI context on - * @napi: the NAPI context to initialize - * @napi_dev: dummy NAPI netdevice, here to not waste the space if the - * driver doesn't use NAPI - * @poll: poll function - * @weight: default weight + * ieee80211_rx_napi - receive frame from NAPI context + * + * Use this function to hand received frames to mac80211. The receive + * buffer in @skb must start with an IEEE 802.11 header. In case of a + * paged @skb is used, the driver is recommended to put the ieee80211 + * header of the frame on the linear part of the @skb to avoid memory + * allocation and/or memcpy by the stack. + * + * This function may not be called in IRQ context. Calls to this function + * for a single hardware must be synchronized against each other. Calls to + * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be + * mixed for a single hardware. Must not run concurrently with + * ieee80211_tx_status() or ieee80211_tx_status_ni(). + * + * This function must be called with BHs disabled. * - * See also netif_napi_add(). + * @hw: the hardware this frame came in on + * @skb: the buffer to receive, owned by mac80211 after this call + * @napi: the NAPI context */ -void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi, - struct net_device *napi_dev, - int (*poll)(struct napi_struct *, int), - int weight); +void ieee80211_rx_napi(struct ieee80211_hw *hw, struct sk_buff *skb, + struct napi_struct *napi); /** * ieee80211_rx - receive frame @@ -3731,7 +3746,10 @@ void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi, * @hw: the hardware this frame came in on * @skb: the buffer to receive, owned by mac80211 after this call */ -void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb); +static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb) +{ + ieee80211_rx_napi(hw, skb, NULL); +} /** * ieee80211_rx_irqsafe - receive frame @@ -4315,19 +4333,6 @@ void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf, struct sk_buff *skb, u8 *p2k); /** - * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys - * - * This function computes the two AES-CMAC sub-keys, based on the - * previously installed master key. - * - * @keyconf: the parameter passed with the set key - * @k1: a buffer to be filled with the 1st sub-key - * @k2: a buffer to be filled with the 2nd sub-key - */ -void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf, - u8 *k1, u8 *k2); - -/** * ieee80211_get_key_tx_seq - get key TX sequence counter * * @keyconf: the parameter passed with the set key |