diff options
Diffstat (limited to 'kernel/power/Kconfig')
| -rw-r--r-- | kernel/power/Kconfig | 278 |
1 files changed, 278 insertions, 0 deletions
diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig index 68d3ebc12..5f93a3ccd 100644 --- a/kernel/power/Kconfig +++ b/kernel/power/Kconfig @@ -101,6 +101,284 @@ config PM_STD_PARTITION suspended image to. It will simply pick the first available swap device. +menuconfig TOI_CORE + bool "Enhanced Hibernation (TuxOnIce)" + depends on HIBERNATION + default y + ---help--- + TuxOnIce is the 'new and improved' suspend support. + + See the TuxOnIce home page (tuxonice.net) + for FAQs, HOWTOs and other documentation. + + comment "Image Storage (you need at least one allocator)" + depends on TOI_CORE + + config TOI_FILE + bool "File Allocator" + depends on TOI_CORE + default y + ---help--- + This option enables support for storing an image in a + simple file. You might want this if your swap is + sometimes full enough that you don't have enough spare + space to store an image. + + config TOI_SWAP + bool "Swap Allocator" + depends on TOI_CORE && SWAP + default y + ---help--- + This option enables support for storing an image in your + swap space. + + comment "General Options" + depends on TOI_CORE + + config TOI_PRUNE + bool "Image pruning support" + depends on TOI_CORE && CRYPTO && BROKEN + default y + ---help--- + This option adds support for using cryptoapi hashing + algorithms to identify pages with the same content. We + then write a much smaller pointer to the first copy of + the data instead of a complete (perhaps compressed) + additional copy. + + You probably want this, so say Y here. + + comment "No image pruning support available without Cryptoapi support." + depends on TOI_CORE && !CRYPTO + + config TOI_CRYPTO + bool "Compression support" + depends on TOI_CORE && CRYPTO + default y + ---help--- + This option adds support for using cryptoapi compression + algorithms. Compression is particularly useful as it can + more than double your suspend and resume speed (depending + upon how well your image compresses). + + You probably want this, so say Y here. + + comment "No compression support available without Cryptoapi support." + depends on TOI_CORE && !CRYPTO + + config TOI_USERUI + bool "Userspace User Interface support" + depends on TOI_CORE && NET && (VT || SERIAL_CONSOLE) + default y + ---help--- + This option enabled support for a userspace based user interface + to TuxOnIce, which allows you to have a nice display while suspending + and resuming, and also enables features such as pressing escape to + cancel a cycle or interactive debugging. + + config TOI_USERUI_DEFAULT_PATH + string "Default userui program location" + default "/usr/local/sbin/tuxoniceui_text" + depends on TOI_USERUI + ---help--- + This entry allows you to specify a default path to the userui binary. + + config TOI_DEFAULT_IMAGE_SIZE_LIMIT + int "Default image size limit" + range -2 65536 + default "-2" + depends on TOI_CORE + ---help--- + This entry allows you to specify a default image size limit. It can + be overridden at run-time using /sys/power/tuxonice/image_size_limit. + + config TOI_KEEP_IMAGE + bool "Allow Keep Image Mode" + depends on TOI_CORE + ---help--- + This option allows you to keep and image and reuse it. It is intended + __ONLY__ for use with systems where all filesystems are mounted read- + only (kiosks, for example). To use it, compile this option in and boot + normally. Set the KEEP_IMAGE flag in /sys/power/tuxonice and suspend. + When you resume, the image will not be removed. You will be unable to turn + off swap partitions (assuming you are using the swap allocator), but future + suspends simply do a power-down. The image can be updated using the + kernel command line parameter suspend_act= to turn off the keep image + bit. Keep image mode is a little less user friendly on purpose - it + should not be used without thought! + + config TOI_INCREMENTAL + bool "Incremental Image Support" + depends on TOI_CORE && 64BIT && TOI_KEEP_IMAGE + default n + ---help--- + This option enables the work in progress toward using the dirty page + tracking to record changes to pages. It is hoped that + this will be an initial step toward implementing storing just + the differences between consecutive images, which will + increase the amount of storage needed for the image, but also + increase the speed at which writing an image occurs and + reduce the wear and tear on drives. + + At the moment, all that is implemented is the first step of keeping + an existing image and then comparing it to the contents in memory + (by setting /sys/power/tuxonice/verify_image to 1 and triggering a + (fake) resume) to see what the page change tracking should find to be + different. If you have verify_image set to 1, TuxOnIce will automatically + invalidate the old image when you next try to hibernate, so there's no + greater chance of disk corruption than normal. + + comment "No incremental image support available without Keep Image support." + depends on TOI_CORE && !TOI_KEEP_IMAGE && 64BIT + + config TOI_REPLACE_SWSUSP + bool "Replace swsusp by default" + default y + depends on TOI_CORE + ---help--- + TuxOnIce can replace swsusp. This option makes that the default state, + requiring you to echo 0 > /sys/power/tuxonice/replace_swsusp if you want + to use the vanilla kernel functionality. Note that your initrd/ramfs will + need to do this before trying to resume, too. + With overriding swsusp enabled, echoing disk to /sys/power/state will + start a TuxOnIce cycle. If resume= doesn't specify an allocator and both + the swap and file allocators are compiled in, the swap allocator will be + used by default. + + config TOI_IGNORE_LATE_INITCALL + bool "Wait for initrd/ramfs to run, by default" + default n + depends on TOI_CORE + ---help--- + When booting, TuxOnIce can check for an image and start to resume prior + to any initrd/ramfs running (via a late initcall). + + If you don't have an initrd/ramfs, this is what you want to happen - + otherwise you won't be able to safely resume. You should set this option + to 'No'. + + If, however, you want your initrd/ramfs to run anyway before resuming, + you need to tell TuxOnIce to ignore that earlier opportunity to resume. + This can be done either by using this compile time option, or by + overriding this option with the boot-time parameter toi_initramfs_resume_only=1. + + Note that if TuxOnIce can't resume at the earlier opportunity, the + value of this option won't matter - the initramfs/initrd (if any) will + run anyway. + + menuconfig TOI_CLUSTER + bool "Cluster support" + default n + depends on TOI_CORE && NET && BROKEN + ---help--- + Support for linking multiple machines in a cluster so that they suspend + and resume together. + + config TOI_DEFAULT_CLUSTER_INTERFACE + string "Default cluster interface" + depends on TOI_CLUSTER + ---help--- + The default interface on which to communicate with other nodes in + the cluster. + + If no value is set here, cluster support will be disabled by default. + + config TOI_DEFAULT_CLUSTER_KEY + string "Default cluster key" + default "Default" + depends on TOI_CLUSTER + ---help--- + The default key used by this node. All nodes in the same cluster + have the same key. Multiple clusters may coexist on the same lan + by using different values for this key. + + config TOI_CLUSTER_IMAGE_TIMEOUT + int "Timeout when checking for image" + default 15 + depends on TOI_CLUSTER + ---help--- + Timeout (seconds) before continuing to boot when waiting to see + whether other nodes might have an image. Set to -1 to wait + indefinitely. In WAIT_UNTIL_NODES is non zero, we might continue + booting sooner than this timeout. + + config TOI_CLUSTER_WAIT_UNTIL_NODES + int "Nodes without image before continuing" + default 0 + depends on TOI_CLUSTER + ---help--- + When booting and no image is found, we wait to see if other nodes + have an image before continuing to boot. This value lets us + continue after seeing a certain number of nodes without an image, + instead of continuing to wait for the timeout. Set to 0 to only + use the timeout. + + config TOI_DEFAULT_CLUSTER_PRE_HIBERNATE + string "Default pre-hibernate script" + depends on TOI_CLUSTER + ---help--- + The default script to be called when starting to hibernate. + + config TOI_DEFAULT_CLUSTER_POST_HIBERNATE + string "Default post-hibernate script" + depends on TOI_CLUSTER + ---help--- + The default script to be called after resuming from hibernation. + + config TOI_DEFAULT_WAIT + int "Default waiting time for emergency boot messages" + default "25" + range -1 32768 + depends on TOI_CORE + help + TuxOnIce can display warnings very early in the process of resuming, + if (for example) it appears that you have booted a kernel that doesn't + match an image on disk. It can then give you the opportunity to either + continue booting that kernel, or reboot the machine. This option can be + used to control how long to wait in such circumstances. -1 means wait + forever. 0 means don't wait at all (do the default action, which will + generally be to continue booting and remove the image). Values of 1 or + more indicate a number of seconds (up to 255) to wait before doing the + default. + + config TOI_DEFAULT_EXTRA_PAGES_ALLOWANCE + int "Default extra pages allowance" + default "2000" + range 500 32768 + depends on TOI_CORE + help + This value controls the default for the allowance TuxOnIce makes for + drivers to allocate extra memory during the atomic copy. The default + value of 2000 will be okay in most cases. If you are using + DRI, the easiest way to find what value to use is to try to hibernate + and look at how many pages were actually needed in the sysfs entry + /sys/power/tuxonice/debug_info (first number on the last line), adding + a little extra because the value is not always the same. + + config TOI_CHECKSUM + bool "Checksum pageset2" + default n + depends on TOI_CORE + select CRYPTO + select CRYPTO_ALGAPI + select CRYPTO_MD4 + ---help--- + Adds support for checksumming pageset2 pages, to ensure you really get an + atomic copy. Since some filesystems (XFS especially) change metadata even + when there's no other activity, we need this to check for pages that have + been changed while we were saving the page cache. If your debugging output + always says no pages were resaved, you may be able to safely disable this + option. + +config TOI + bool + depends on TOI_CORE!=n + default y + +config TOI_ZRAM_SUPPORT + def_bool y + depends on TOI && ZRAM!=n + config PM_SLEEP def_bool y depends on SUSPEND || HIBERNATE_CALLBACKS |