diff options
Diffstat (limited to 'samples/pktgen')
| -rw-r--r-- | samples/pktgen/README.rst | 43 | ||||
| -rw-r--r-- | samples/pktgen/functions.sh | 121 | ||||
| -rw-r--r-- | samples/pktgen/parameters.sh | 97 | ||||
| -rw-r--r-- | samples/pktgen/pktgen.conf-1-1 | 59 | ||||
| -rw-r--r-- | samples/pktgen/pktgen.conf-2-1 | 66 | ||||
| -rw-r--r-- | samples/pktgen/pktgen.conf-2-2 | 73 | ||||
| -rwxr-xr-x | samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh | 86 | ||||
| -rwxr-xr-x | samples/pktgen/pktgen_sample01_simple.sh | 71 | ||||
| -rwxr-xr-x | samples/pktgen/pktgen_sample02_multiqueue.sh | 75 | ||||
| -rwxr-xr-x | samples/pktgen/pktgen_sample03_burst_single_flow.sh | 82 |
10 files changed, 575 insertions, 198 deletions
diff --git a/samples/pktgen/README.rst b/samples/pktgen/README.rst new file mode 100644 index 000000000..8365c4e5c --- /dev/null +++ b/samples/pktgen/README.rst @@ -0,0 +1,43 @@ +Sample and benchmark scripts for pktgen (packet generator) +========================================================== +This directory contains some pktgen sample and benchmark scripts, that +can easily be copied and adjusted for your own use-case. + +General doc is located in kernel: Documentation/networking/pktgen.txt + +Helper include files +==================== +This directory contains two helper shell files, that can be "included" +by shell source'ing. Namely "functions.sh" and "parameters.sh". + +Common parameters +----------------- +The parameters.sh file support easy and consistant parameter parsing +across the sample scripts. Usage example is printed on errors:: + + Usage: ./pktgen_sample01_simple.sh [-vx] -i ethX + -i : ($DEV) output interface/device (required) + -s : ($PKT_SIZE) packet size + -d : ($DEST_IP) destination IP + -m : ($DST_MAC) destination MAC-addr + -t : ($THREADS) threads to start + -c : ($SKB_CLONE) SKB clones send before alloc new SKB + -b : ($BURST) HW level bursting of SKBs + -v : ($VERBOSE) verbose + -x : ($DEBUG) debug + +The global variable being set is also listed. E.g. the required +interface/device parameter "-i" sets variable $DEV. + +Common functions +---------------- +The functions.sh file provides; Three different shell functions for +configuring the different components of pktgen: pg_ctrl(), pg_thread() +and pg_set(). + +These functions correspond to pktgens different components. + * pg_ctrl() control "pgctrl" (/proc/net/pktgen/pgctrl) + * pg_thread() control the kernel threads and binding to devices + * pg_set() control setup of individual devices + +See sample scripts for usage examples. diff --git a/samples/pktgen/functions.sh b/samples/pktgen/functions.sh new file mode 100644 index 000000000..205e4cde4 --- /dev/null +++ b/samples/pktgen/functions.sh @@ -0,0 +1,121 @@ +# +# Common functions used by pktgen scripts +# - Depending on bash 3 (or higher) syntax +# +# Author: Jesper Dangaaard Brouer +# License: GPL + +## -- General shell logging cmds -- +function err() { + local exitcode=$1 + shift + echo "ERROR: $@" >&2 + exit $exitcode +} + +function warn() { + echo "WARN : $@" >&2 +} + +function info() { + if [[ -n "$VERBOSE" ]]; then + echo "INFO : $@" >&2 + fi +} + +## -- Pktgen proc config commands -- ## +export PROC_DIR=/proc/net/pktgen +# +# Three different shell functions for configuring the different +# components of pktgen: +# pg_ctrl(), pg_thread() and pg_set(). +# +# These functions correspond to pktgens different components. +# * pg_ctrl() control "pgctrl" (/proc/net/pktgen/pgctrl) +# * pg_thread() control the kernel threads and binding to devices +# * pg_set() control setup of individual devices +function pg_ctrl() { + local proc_file="pgctrl" + proc_cmd ${proc_file} "$@" +} + +function pg_thread() { + local thread=$1 + local proc_file="kpktgend_${thread}" + shift + proc_cmd ${proc_file} "$@" +} + +function pg_set() { + local dev=$1 + local proc_file="$dev" + shift + proc_cmd ${proc_file} "$@" +} + +# More generic replacement for pgset(), that does not depend on global +# variable for proc file. +function proc_cmd() { + local result + local proc_file=$1 + # after shift, the remaining args are contained in $@ + shift + local proc_ctrl=${PROC_DIR}/$proc_file + if [[ ! -e "$proc_ctrl" ]]; then + err 3 "proc file:$proc_ctrl does not exists (dev added to thread?)" + else + if [[ ! -w "$proc_ctrl" ]]; then + err 4 "proc file:$proc_ctrl not writable, not root?!" + fi + fi + + if [[ "$DEBUG" == "yes" ]]; then + echo "cmd: $@ > $proc_ctrl" + fi + # Quoting of "$@" is important for space expansion + echo "$@" > "$proc_ctrl" + local status=$? + + result=$(grep "Result: OK:" $proc_ctrl) + # Due to pgctrl, cannot use exit code $? from grep + if [[ "$result" == "" ]]; then + grep "Result:" $proc_ctrl >&2 + fi + if (( $status != 0 )); then + err 5 "Write error($status) occurred cmd: \"$@ > $proc_ctrl\"" + fi +} + +# Old obsolete "pgset" function, with slightly improved err handling +function pgset() { + local result + + if [[ "$DEBUG" == "yes" ]]; then + echo "cmd: $1 > $PGDEV" + fi + echo $1 > $PGDEV + local status=$? + + result=`cat $PGDEV | fgrep "Result: OK:"` + if [[ "$result" == "" ]]; then + cat $PGDEV | fgrep Result: + fi + if (( $status != 0 )); then + err 5 "Write error($status) occurred cmd: \"$1 > $PGDEV\"" + fi +} + +## -- General shell tricks -- + +function root_check_run_with_sudo() { + # Trick so, program can be run as normal user, will just use "sudo" + # call as root_check_run_as_sudo "$@" + if [ "$EUID" -ne 0 ]; then + if [ -x $0 ]; then # Directly executable use sudo + info "Not root, running with sudo" + sudo "$0" "$@" + exit $? + fi + err 4 "cannot perform sudo run of $0" + fi +} diff --git a/samples/pktgen/parameters.sh b/samples/pktgen/parameters.sh new file mode 100644 index 000000000..33b70fdd5 --- /dev/null +++ b/samples/pktgen/parameters.sh @@ -0,0 +1,97 @@ +# +# Common parameter parsing for pktgen scripts +# + +function usage() { + echo "" + echo "Usage: $0 [-vx] -i ethX" + echo " -i : (\$DEV) output interface/device (required)" + echo " -s : (\$PKT_SIZE) packet size" + echo " -d : (\$DEST_IP) destination IP" + echo " -m : (\$DST_MAC) destination MAC-addr" + echo " -t : (\$THREADS) threads to start" + echo " -c : (\$SKB_CLONE) SKB clones send before alloc new SKB" + echo " -b : (\$BURST) HW level bursting of SKBs" + echo " -v : (\$VERBOSE) verbose" + echo " -x : (\$DEBUG) debug" + echo "" +} + +## --- Parse command line arguments / parameters --- +## echo "Commandline options:" +while getopts "s:i:d:m:t:c:b:vxh" option; do + case $option in + i) # interface + export DEV=$OPTARG + info "Output device set to: DEV=$DEV" + ;; + s) + export PKT_SIZE=$OPTARG + info "Packet size set to: PKT_SIZE=$PKT_SIZE bytes" + ;; + d) # destination IP + export DEST_IP=$OPTARG + info "Destination IP set to: DEST_IP=$DEST_IP" + ;; + m) # MAC + export DST_MAC=$OPTARG + info "Destination MAC set to: DST_MAC=$DST_MAC" + ;; + t) + export THREADS=$OPTARG + export CPU_THREADS=$OPTARG + let "CPU_THREADS -= 1" + info "Number of threads to start: $THREADS (0 to $CPU_THREADS)" + ;; + c) + export CLONE_SKB=$OPTARG + info "CLONE_SKB=$CLONE_SKB" + ;; + b) + export BURST=$OPTARG + info "SKB bursting: BURST=$BURST" + ;; + v) + export VERBOSE=yes + info "Verbose mode: VERBOSE=$VERBOSE" + ;; + x) + export DEBUG=yes + info "Debug mode: DEBUG=$DEBUG" + ;; + h|?|*) + usage; + err 2 "[ERROR] Unknown parameters!!!" + esac +done +shift $(( $OPTIND - 1 )) + +if [ -z "$PKT_SIZE" ]; then + # NIC adds 4 bytes CRC + export PKT_SIZE=60 + info "Default packet size set to: set to: $PKT_SIZE bytes" +fi + +if [ -z "$THREADS" ]; then + # Zero CPU threads means one thread, because CPU numbers are zero indexed + export CPU_THREADS=0 + export THREADS=1 +fi + +if [ -z "$DEV" ]; then + usage + err 2 "Please specify output device" +fi + +if [ -z "$DST_MAC" ]; then + warn "Missing destination MAC address" +fi + +if [ -z "$DEST_IP" ]; then + warn "Missing destination IP address" +fi + +if [ ! -d /proc/net/pktgen ]; then + info "Loading kernel module: pktgen" + modprobe pktgen +fi diff --git a/samples/pktgen/pktgen.conf-1-1 b/samples/pktgen/pktgen.conf-1-1 deleted file mode 100644 index f91daad9e..000000000 --- a/samples/pktgen/pktgen.conf-1-1 +++ /dev/null @@ -1,59 +0,0 @@ -#!/bin/bash - -#modprobe pktgen - - -function pgset() { - local result - - echo $1 > $PGDEV - - result=`cat $PGDEV | fgrep "Result: OK:"` - if [ "$result" = "" ]; then - cat $PGDEV | fgrep Result: - fi -} - -# Config Start Here ----------------------------------------------------------- - - -# thread config -# Each CPU has its own thread. One CPU example. We add eth1. - -PGDEV=/proc/net/pktgen/kpktgend_0 - echo "Removing all devices" - pgset "rem_device_all" - echo "Adding eth1" - pgset "add_device eth1" - - -# device config -# delay 0 means maximum speed. - -CLONE_SKB="clone_skb 1000000" -# NIC adds 4 bytes CRC -PKT_SIZE="pkt_size 60" - -# COUNT 0 means forever -#COUNT="count 0" -COUNT="count 10000000" -DELAY="delay 0" - -PGDEV=/proc/net/pktgen/eth1 - echo "Configuring $PGDEV" - pgset "$COUNT" - pgset "$CLONE_SKB" - pgset "$PKT_SIZE" - pgset "$DELAY" - pgset "dst 10.10.11.2" - pgset "dst_mac 00:04:23:08:91:dc" - - -# Time to run -PGDEV=/proc/net/pktgen/pgctrl - - echo "Running... ctrl^C to stop" - trap true INT - pgset "start" - echo "Done" - cat /proc/net/pktgen/eth1 diff --git a/samples/pktgen/pktgen.conf-2-1 b/samples/pktgen/pktgen.conf-2-1 deleted file mode 100644 index e108e97d6..000000000 --- a/samples/pktgen/pktgen.conf-2-1 +++ /dev/null @@ -1,66 +0,0 @@ -#!/bin/bash - -#modprobe pktgen - - -function pgset() { - local result - - echo $1 > $PGDEV - - result=`cat $PGDEV | fgrep "Result: OK:"` - if [ "$result" = "" ]; then - cat $PGDEV | fgrep Result: - fi -} - -# Config Start Here ----------------------------------------------------------- - - -# thread config -# Each CPU has its own thread. Two CPU example. We add eth1 to the first -# and leave the second idle. - -PGDEV=/proc/net/pktgen/kpktgend_0 - echo "Removing all devices" - pgset "rem_device_all" - echo "Adding eth1" - pgset "add_device eth1" - -# We need to remove old config since we dont use this thread. We can only -# one NIC on one CPU due to affinity reasons. - -PGDEV=/proc/net/pktgen/kpktgend_1 - echo "Removing all devices" - pgset "rem_device_all" - -# device config -# delay 0 means maximum speed. - -CLONE_SKB="clone_skb 1000000" -# NIC adds 4 bytes CRC -PKT_SIZE="pkt_size 60" - -# COUNT 0 means forever -#COUNT="count 0" -COUNT="count 10000000" -DELAY="delay 0" - -PGDEV=/proc/net/pktgen/eth1 - echo "Configuring $PGDEV" - pgset "$COUNT" - pgset "$CLONE_SKB" - pgset "$PKT_SIZE" - pgset "$DELAY" - pgset "dst 10.10.11.2" - pgset "dst_mac 00:04:23:08:91:dc" - - -# Time to run -PGDEV=/proc/net/pktgen/pgctrl - - echo "Running... ctrl^C to stop" - trap true INT - pgset "start" - echo "Done" - cat /proc/net/pktgen/eth1 diff --git a/samples/pktgen/pktgen.conf-2-2 b/samples/pktgen/pktgen.conf-2-2 deleted file mode 100644 index acea15503..000000000 --- a/samples/pktgen/pktgen.conf-2-2 +++ /dev/null @@ -1,73 +0,0 @@ -#!/bin/bash - -#modprobe pktgen - - -function pgset() { - local result - - echo $1 > $PGDEV - - result=`cat $PGDEV | fgrep "Result: OK:"` - if [ "$result" = "" ]; then - cat $PGDEV | fgrep Result: - fi -} - -# Config Start Here ----------------------------------------------------------- - - -# thread config -# Each CPU has its own thread. Two CPU example. We add eth1, eth2 respectively. - -PGDEV=/proc/net/pktgen/kpktgend_0 - echo "Removing all devices" - pgset "rem_device_all" - echo "Adding eth1" - pgset "add_device eth1" - -PGDEV=/proc/net/pktgen/kpktgend_1 - echo "Removing all devices" - pgset "rem_device_all" - echo "Adding eth2" - pgset "add_device eth2" - - -# device config -# delay 0 means maximum speed. - -CLONE_SKB="clone_skb 1000000" -# NIC adds 4 bytes CRC -PKT_SIZE="pkt_size 60" - -# COUNT 0 means forever -#COUNT="count 0" -COUNT="count 10000000" -DELAY="delay 0" - -PGDEV=/proc/net/pktgen/eth1 - echo "Configuring $PGDEV" - pgset "$COUNT" - pgset "$CLONE_SKB" - pgset "$PKT_SIZE" - pgset "$DELAY" - pgset "dst 10.10.11.2" - pgset "dst_mac 00:04:23:08:91:dc" - -PGDEV=/proc/net/pktgen/eth2 - echo "Configuring $PGDEV" - pgset "$COUNT" - pgset "$CLONE_SKB" - pgset "$PKT_SIZE" - pgset "$DELAY" - pgset "dst 192.168.2.2" - pgset "dst_mac 00:04:23:08:91:de" - -# Time to run -PGDEV=/proc/net/pktgen/pgctrl - - echo "Running... ctrl^C to stop" - trap true INT - pgset "start" - echo "Done" - cat /proc/net/pktgen/eth1 /proc/net/pktgen/eth2 diff --git a/samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh b/samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh new file mode 100755 index 000000000..cb1590331 --- /dev/null +++ b/samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh @@ -0,0 +1,86 @@ +#!/bin/bash +# +# Benchmark script: +# - developed for benchmarking ingress qdisc path +# +# Script for injecting packets into RX path of the stack with pktgen +# "xmit_mode netif_receive". With an invalid dst_mac this will only +# measure the ingress code path as packets gets dropped in ip_rcv(). +# +# This script don't really need any hardware. It benchmarks software +# RX path just after NIC driver level. With bursting is also +# "removes" the SKB alloc/free overhead. +# +# Setup scenarios for measuring ingress qdisc (with invalid dst_mac): +# ------------------------------------------------------------------ +# (1) no ingress (uses static_key_false(&ingress_needed)) +# +# (2) ingress on other dev (change ingress_needed and calls +# handle_ing() but exit early) +# +# config: tc qdisc add dev $SOMEDEV handle ffff: ingress +# +# (3) ingress on this dev, handle_ing() -> tc_classify() +# +# config: tc qdisc add dev $DEV handle ffff: ingress +# +# (4) ingress on this dev + drop at u32 classifier/action. +# +basedir=`dirname $0` +source ${basedir}/functions.sh +root_check_run_with_sudo "$@" + +# Parameter parsing via include +source ${basedir}/parameters.sh +# Using invalid DST_MAC will cause the packets to get dropped in +# ip_rcv() which is part of the test +[ -z "$DEST_IP" ] && DEST_IP="198.18.0.42" +[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" +[ -z "$BURST" ] && BURST=1024 + +# Base Config +DELAY="0" # Zero means max speed +COUNT="10000000" # Zero means indefinitely + +# General cleanup everything since last run +pg_ctrl "reset" + +# Threads are specified with parameter -t value in $THREADS +for ((thread = 0; thread < $THREADS; thread++)); do + # The device name is extended with @name, using thread number to + # make then unique, but any name will do. + dev=${DEV}@${thread} + + # Add remove all other devices and add_device $dev to thread + pg_thread $thread "rem_device_all" + pg_thread $thread "add_device" $dev + + # Base config of dev + pg_set $dev "flag QUEUE_MAP_CPU" + pg_set $dev "count $COUNT" + pg_set $dev "pkt_size $PKT_SIZE" + pg_set $dev "delay $DELAY" + pg_set $dev "flag NO_TIMESTAMP" + + # Destination + pg_set $dev "dst_mac $DST_MAC" + pg_set $dev "dst $DEST_IP" + + # Inject packet into RX path of stack + pg_set $dev "xmit_mode netif_receive" + + # Burst allow us to avoid measuring SKB alloc/free overhead + pg_set $dev "burst $BURST" +done + +# start_run +echo "Running... ctrl^C to stop" >&2 +pg_ctrl "start" +echo "Done" >&2 + +# Print results +for ((thread = 0; thread < $THREADS; thread++)); do + dev=${DEV}@${thread} + echo "Device: $dev" + cat /proc/net/pktgen/$dev | grep -A2 "Result:" +done diff --git a/samples/pktgen/pktgen_sample01_simple.sh b/samples/pktgen/pktgen_sample01_simple.sh new file mode 100755 index 000000000..8c9d318c2 --- /dev/null +++ b/samples/pktgen/pktgen_sample01_simple.sh @@ -0,0 +1,71 @@ +#!/bin/bash +# +# Simple example: +# * pktgen sending with single thread and single interface +# * flow variation via random UDP source port +# +basedir=`dirname $0` +source ${basedir}/functions.sh +root_check_run_with_sudo "$@" + +# Parameter parsing via include +# - go look in parameters.sh to see which setting are avail +# - required param is the interface "-i" stored in $DEV +source ${basedir}/parameters.sh +# +# Set some default params, if they didn't get set +[ -z "$DEST_IP" ] && DEST_IP="198.18.0.42" +[ -z "$CLONE_SKB" ] && CLONE_SKB="0" +# Example enforce param "-m" for dst_mac +[ -z "$DST_MAC" ] && usage && err 2 "Must specify -m dst_mac" + +# Base Config +DELAY="0" # Zero means max speed +COUNT="100000" # Zero means indefinitely + +# Flow variation random source port between min and max +UDP_MIN=9 +UDP_MAX=109 + +# General cleanup everything since last run +# (especially important if other threads were configured by other scripts) +pg_ctrl "reset" + +# Add remove all other devices and add_device $DEV to thread 0 +thread=0 +pg_thread $thread "rem_device_all" +pg_thread $thread "add_device" $DEV + +# How many packets to send (zero means indefinitely) +pg_set $DEV "count $COUNT" + +# Reduce alloc cost by sending same SKB many times +# - this obviously affects the randomness within the packet +pg_set $DEV "clone_skb $CLONE_SKB" + +# Set packet size +pg_set $DEV "pkt_size $PKT_SIZE" + +# Delay between packets (zero means max speed) +pg_set $DEV "delay $DELAY" + +# Flag example disabling timestamping +pg_set $DEV "flag NO_TIMESTAMP" + +# Destination +pg_set $DEV "dst_mac $DST_MAC" +pg_set $DEV "dst $DEST_IP" + +# Setup random UDP port src range +pg_set $DEV "flag UDPSRC_RND" +pg_set $DEV "udp_src_min $UDP_MIN" +pg_set $DEV "udp_src_max $UDP_MAX" + +# start_run +echo "Running... ctrl^C to stop" >&2 +pg_ctrl "start" +echo "Done" >&2 + +# Print results +echo "Result device: $DEV" +cat /proc/net/pktgen/$DEV diff --git a/samples/pktgen/pktgen_sample02_multiqueue.sh b/samples/pktgen/pktgen_sample02_multiqueue.sh new file mode 100755 index 000000000..32467aea8 --- /dev/null +++ b/samples/pktgen/pktgen_sample02_multiqueue.sh @@ -0,0 +1,75 @@ +#!/bin/bash +# +# Multiqueue: Using pktgen threads for sending on multiple CPUs +# * adding devices to kernel threads +# * notice the naming scheme for keeping device names unique +# * nameing scheme: dev@thread_number +# * flow variation via random UDP source port +# +basedir=`dirname $0` +source ${basedir}/functions.sh +root_check_run_with_sudo "$@" +# +# Required param: -i dev in $DEV +source ${basedir}/parameters.sh + +# Base Config +DELAY="0" # Zero means max speed +COUNT="100000" # Zero means indefinitely +[ -z "$CLONE_SKB" ] && CLONE_SKB="0" + +# Flow variation random source port between min and max +UDP_MIN=9 +UDP_MAX=109 + +# (example of setting default params in your script) +[ -z "$DEST_IP" ] && DEST_IP="198.18.0.42" +[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" + +# General cleanup everything since last run +pg_ctrl "reset" + +# Threads are specified with parameter -t value in $THREADS +for ((thread = 0; thread < $THREADS; thread++)); do + # The device name is extended with @name, using thread number to + # make then unique, but any name will do. + dev=${DEV}@${thread} + + # Add remove all other devices and add_device $dev to thread + pg_thread $thread "rem_device_all" + pg_thread $thread "add_device" $dev + + # Notice config queue to map to cpu (mirrors smp_processor_id()) + # It is beneficial to map IRQ /proc/irq/*/smp_affinity 1:1 to CPU number + pg_set $dev "flag QUEUE_MAP_CPU" + + # Base config of dev + pg_set $dev "count $COUNT" + pg_set $dev "clone_skb $CLONE_SKB" + pg_set $dev "pkt_size $PKT_SIZE" + pg_set $dev "delay $DELAY" + + # Flag example disabling timestamping + pg_set $dev "flag NO_TIMESTAMP" + + # Destination + pg_set $dev "dst_mac $DST_MAC" + pg_set $dev "dst $DEST_IP" + + # Setup random UDP port src range + pg_set $dev "flag UDPSRC_RND" + pg_set $dev "udp_src_min $UDP_MIN" + pg_set $dev "udp_src_max $UDP_MAX" +done + +# start_run +echo "Running... ctrl^C to stop" >&2 +pg_ctrl "start" +echo "Done" >&2 + +# Print results +for ((thread = 0; thread < $THREADS; thread++)); do + dev=${DEV}@${thread} + echo "Device: $dev" + cat /proc/net/pktgen/$dev | grep -A2 "Result:" +done diff --git a/samples/pktgen/pktgen_sample03_burst_single_flow.sh b/samples/pktgen/pktgen_sample03_burst_single_flow.sh new file mode 100755 index 000000000..775f5d0a1 --- /dev/null +++ b/samples/pktgen/pktgen_sample03_burst_single_flow.sh @@ -0,0 +1,82 @@ +#!/bin/bash +# +# Script for max single flow performance +# - If correctly tuned[1], single CPU 10G wirespeed small pkts is possible[2] +# +# Using pktgen "burst" option (use -b $N) +# - To boost max performance +# - Avail since: kernel v3.18 +# * commit 38b2cf2982dc73 ("net: pktgen: packet bursting via skb->xmit_more") +# - This avoids writing the HW tailptr on every driver xmit +# - The performance boost is impressive, see commit and blog [2] +# +# Notice: On purpose generates a single (UDP) flow towards target, +# reason behind this is to only overload/activate a single CPU on +# target host. And no randomness for pktgen also makes it faster. +# +# Tuning see: +# [1] http://netoptimizer.blogspot.dk/2014/06/pktgen-for-network-overload-testing.html +# [2] http://netoptimizer.blogspot.dk/2014/10/unlocked-10gbps-tx-wirespeed-smallest.html +# +basedir=`dirname $0` +source ${basedir}/functions.sh +root_check_run_with_sudo "$@" + +# Parameter parsing via include +source ${basedir}/parameters.sh +# Set some default params, if they didn't get set +[ -z "$DEST_IP" ] && DEST_IP="198.18.0.42" +[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff" +[ -z "$BURST" ] && BURST=32 +[ -z "$CLONE_SKB" ] && CLONE_SKB="100000" + +# Base Config +DELAY="0" # Zero means max speed +COUNT="0" # Zero means indefinitely + +# General cleanup everything since last run +pg_ctrl "reset" + +# Threads are specified with parameter -t value in $THREADS +for ((thread = 0; thread < $THREADS; thread++)); do + dev=${DEV}@${thread} + + # Add remove all other devices and add_device $dev to thread + pg_thread $thread "rem_device_all" + pg_thread $thread "add_device" $dev + + # Base config + pg_set $dev "flag QUEUE_MAP_CPU" + pg_set $dev "count $COUNT" + pg_set $dev "clone_skb $CLONE_SKB" + pg_set $dev "pkt_size $PKT_SIZE" + pg_set $dev "delay $DELAY" + pg_set $dev "flag NO_TIMESTAMP" + + # Destination + pg_set $dev "dst_mac $DST_MAC" + pg_set $dev "dst $DEST_IP" + + # Setup burst, for easy testing -b 0 disable bursting + # (internally in pktgen default and minimum burst=1) + if [[ ${BURST} -ne 0 ]]; then + pg_set $dev "burst $BURST" + else + info "$dev: Not using burst" + fi +done + +# Run if user hits control-c +function control_c() { + # Print results + for ((thread = 0; thread < $THREADS; thread++)); do + dev=${DEV}@${thread} + echo "Device: $dev" + cat /proc/net/pktgen/$dev | grep -A2 "Result:" + done +} +# trap keyboard interrupt (Ctrl-C) +trap control_c SIGINT + +echo "Running... ctrl^C to stop" >&2 +pg_ctrl "start" |