diff options
Diffstat (limited to 'sound/soc/fsl/fsl_ssi.c')
| -rw-r--r-- | sound/soc/fsl/fsl_ssi.c | 1485 |
1 files changed, 1485 insertions, 0 deletions
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c new file mode 100644 index 000000000..0d4880421 --- /dev/null +++ b/sound/soc/fsl/fsl_ssi.c @@ -0,0 +1,1485 @@ +/* + * Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver + * + * Author: Timur Tabi <timur@freescale.com> + * + * Copyright 2007-2010 Freescale Semiconductor, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + * + * + * Some notes why imx-pcm-fiq is used instead of DMA on some boards: + * + * The i.MX SSI core has some nasty limitations in AC97 mode. While most + * sane processor vendors have a FIFO per AC97 slot, the i.MX has only + * one FIFO which combines all valid receive slots. We cannot even select + * which slots we want to receive. The WM9712 with which this driver + * was developed with always sends GPIO status data in slot 12 which + * we receive in our (PCM-) data stream. The only chance we have is to + * manually skip this data in the FIQ handler. With sampling rates different + * from 48000Hz not every frame has valid receive data, so the ratio + * between pcm data and GPIO status data changes. Our FIQ handler is not + * able to handle this, hence this driver only works with 48000Hz sampling + * rate. + * Reading and writing AC97 registers is another challenge. The core + * provides us status bits when the read register is updated with *another* + * value. When we read the same register two times (and the register still + * contains the same value) these status bits are not set. We work + * around this by not polling these bits but only wait a fixed delay. + */ + +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> + +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/initval.h> +#include <sound/soc.h> +#include <sound/dmaengine_pcm.h> + +#include "fsl_ssi.h" +#include "imx-pcm.h" + +/** + * FSLSSI_I2S_RATES: sample rates supported by the I2S + * + * This driver currently only supports the SSI running in I2S slave mode, + * which means the codec determines the sample rate. Therefore, we tell + * ALSA that we support all rates and let the codec driver decide what rates + * are really supported. + */ +#define FSLSSI_I2S_RATES SNDRV_PCM_RATE_CONTINUOUS + +/** + * FSLSSI_I2S_FORMATS: audio formats supported by the SSI + * + * The SSI has a limitation in that the samples must be in the same byte + * order as the host CPU. This is because when multiple bytes are written + * to the STX register, the bytes and bits must be written in the same + * order. The STX is a shift register, so all the bits need to be aligned + * (bit-endianness must match byte-endianness). Processors typically write + * the bits within a byte in the same order that the bytes of a word are + * written in. So if the host CPU is big-endian, then only big-endian + * samples will be written to STX properly. + */ +#ifdef __BIG_ENDIAN +#define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE | \ + SNDRV_PCM_FMTBIT_S18_3BE | SNDRV_PCM_FMTBIT_S20_3BE | \ + SNDRV_PCM_FMTBIT_S24_3BE | SNDRV_PCM_FMTBIT_S24_BE) +#else +#define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE) +#endif + +#define FSLSSI_SIER_DBG_RX_FLAGS (CCSR_SSI_SIER_RFF0_EN | \ + CCSR_SSI_SIER_RLS_EN | CCSR_SSI_SIER_RFS_EN | \ + CCSR_SSI_SIER_ROE0_EN | CCSR_SSI_SIER_RFRC_EN) +#define FSLSSI_SIER_DBG_TX_FLAGS (CCSR_SSI_SIER_TFE0_EN | \ + CCSR_SSI_SIER_TLS_EN | CCSR_SSI_SIER_TFS_EN | \ + CCSR_SSI_SIER_TUE0_EN | CCSR_SSI_SIER_TFRC_EN) + +enum fsl_ssi_type { + FSL_SSI_MCP8610, + FSL_SSI_MX21, + FSL_SSI_MX35, + FSL_SSI_MX51, +}; + +struct fsl_ssi_reg_val { + u32 sier; + u32 srcr; + u32 stcr; + u32 scr; +}; + +struct fsl_ssi_rxtx_reg_val { + struct fsl_ssi_reg_val rx; + struct fsl_ssi_reg_val tx; +}; +static const struct regmap_config fsl_ssi_regconfig = { + .max_register = CCSR_SSI_SACCDIS, + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .val_format_endian = REGMAP_ENDIAN_NATIVE, +}; + +struct fsl_ssi_soc_data { + bool imx; + bool offline_config; + u32 sisr_write_mask; +}; + +/** + * fsl_ssi_private: per-SSI private data + * + * @reg: Pointer to the regmap registers + * @irq: IRQ of this SSI + * @cpu_dai_drv: CPU DAI driver for this device + * + * @dai_fmt: DAI configuration this device is currently used with + * @i2s_mode: i2s and network mode configuration of the device. Is used to + * switch between normal and i2s/network mode + * mode depending on the number of channels + * @use_dma: DMA is used or FIQ with stream filter + * @use_dual_fifo: DMA with support for both FIFOs used + * @fifo_deph: Depth of the SSI FIFOs + * @rxtx_reg_val: Specific register settings for receive/transmit configuration + * + * @clk: SSI clock + * @baudclk: SSI baud clock for master mode + * @baudclk_streams: Active streams that are using baudclk + * @bitclk_freq: bitclock frequency set by .set_dai_sysclk + * + * @dma_params_tx: DMA transmit parameters + * @dma_params_rx: DMA receive parameters + * @ssi_phys: physical address of the SSI registers + * + * @fiq_params: FIQ stream filtering parameters + * + * @pdev: Pointer to pdev used for deprecated fsl-ssi sound card + * + * @dbg_stats: Debugging statistics + * + * @soc: SoC specifc data + */ +struct fsl_ssi_private { + struct regmap *regs; + int irq; + struct snd_soc_dai_driver cpu_dai_drv; + + unsigned int dai_fmt; + u8 i2s_mode; + bool use_dma; + bool use_dual_fifo; + bool has_ipg_clk_name; + unsigned int fifo_depth; + struct fsl_ssi_rxtx_reg_val rxtx_reg_val; + + struct clk *clk; + struct clk *baudclk; + unsigned int baudclk_streams; + unsigned int bitclk_freq; + + /* DMA params */ + struct snd_dmaengine_dai_dma_data dma_params_tx; + struct snd_dmaengine_dai_dma_data dma_params_rx; + dma_addr_t ssi_phys; + + /* params for non-dma FIQ stream filtered mode */ + struct imx_pcm_fiq_params fiq_params; + + /* Used when using fsl-ssi as sound-card. This is only used by ppc and + * should be replaced with simple-sound-card. */ + struct platform_device *pdev; + + struct fsl_ssi_dbg dbg_stats; + + const struct fsl_ssi_soc_data *soc; +}; + +/* + * imx51 and later SoCs have a slightly different IP that allows the + * SSI configuration while the SSI unit is running. + * + * More important, it is necessary on those SoCs to configure the + * sperate TX/RX DMA bits just before starting the stream + * (fsl_ssi_trigger). The SDMA unit has to be configured before fsl_ssi + * sends any DMA requests to the SDMA unit, otherwise it is not defined + * how the SDMA unit handles the DMA request. + * + * SDMA units are present on devices starting at imx35 but the imx35 + * reference manual states that the DMA bits should not be changed + * while the SSI unit is running (SSIEN). So we support the necessary + * online configuration of fsl-ssi starting at imx51. + */ + +static struct fsl_ssi_soc_data fsl_ssi_mpc8610 = { + .imx = false, + .offline_config = true, + .sisr_write_mask = CCSR_SSI_SISR_RFRC | CCSR_SSI_SISR_TFRC | + CCSR_SSI_SISR_ROE0 | CCSR_SSI_SISR_ROE1 | + CCSR_SSI_SISR_TUE0 | CCSR_SSI_SISR_TUE1, +}; + +static struct fsl_ssi_soc_data fsl_ssi_imx21 = { + .imx = true, + .offline_config = true, + .sisr_write_mask = 0, +}; + +static struct fsl_ssi_soc_data fsl_ssi_imx35 = { + .imx = true, + .offline_config = true, + .sisr_write_mask = CCSR_SSI_SISR_RFRC | CCSR_SSI_SISR_TFRC | + CCSR_SSI_SISR_ROE0 | CCSR_SSI_SISR_ROE1 | + CCSR_SSI_SISR_TUE0 | CCSR_SSI_SISR_TUE1, +}; + +static struct fsl_ssi_soc_data fsl_ssi_imx51 = { + .imx = true, + .offline_config = false, + .sisr_write_mask = CCSR_SSI_SISR_ROE0 | CCSR_SSI_SISR_ROE1 | + CCSR_SSI_SISR_TUE0 | CCSR_SSI_SISR_TUE1, +}; + +static const struct of_device_id fsl_ssi_ids[] = { + { .compatible = "fsl,mpc8610-ssi", .data = &fsl_ssi_mpc8610 }, + { .compatible = "fsl,imx51-ssi", .data = &fsl_ssi_imx51 }, + { .compatible = "fsl,imx35-ssi", .data = &fsl_ssi_imx35 }, + { .compatible = "fsl,imx21-ssi", .data = &fsl_ssi_imx21 }, + {} +}; +MODULE_DEVICE_TABLE(of, fsl_ssi_ids); + +static bool fsl_ssi_is_ac97(struct fsl_ssi_private *ssi_private) +{ + return !!(ssi_private->dai_fmt & SND_SOC_DAIFMT_AC97); +} + +static bool fsl_ssi_is_i2s_master(struct fsl_ssi_private *ssi_private) +{ + return (ssi_private->dai_fmt & SND_SOC_DAIFMT_MASTER_MASK) == + SND_SOC_DAIFMT_CBS_CFS; +} + +static bool fsl_ssi_is_i2s_cbm_cfs(struct fsl_ssi_private *ssi_private) +{ + return (ssi_private->dai_fmt & SND_SOC_DAIFMT_MASTER_MASK) == + SND_SOC_DAIFMT_CBM_CFS; +} +/** + * fsl_ssi_isr: SSI interrupt handler + * + * Although it's possible to use the interrupt handler to send and receive + * data to/from the SSI, we use the DMA instead. Programming is more + * complicated, but the performance is much better. + * + * This interrupt handler is used only to gather statistics. + * + * @irq: IRQ of the SSI device + * @dev_id: pointer to the ssi_private structure for this SSI device + */ +static irqreturn_t fsl_ssi_isr(int irq, void *dev_id) +{ + struct fsl_ssi_private *ssi_private = dev_id; + struct regmap *regs = ssi_private->regs; + __be32 sisr; + __be32 sisr2; + + /* We got an interrupt, so read the status register to see what we + were interrupted for. We mask it with the Interrupt Enable register + so that we only check for events that we're interested in. + */ + regmap_read(regs, CCSR_SSI_SISR, &sisr); + + sisr2 = sisr & ssi_private->soc->sisr_write_mask; + /* Clear the bits that we set */ + if (sisr2) + regmap_write(regs, CCSR_SSI_SISR, sisr2); + + fsl_ssi_dbg_isr(&ssi_private->dbg_stats, sisr); + + return IRQ_HANDLED; +} + +/* + * Enable/Disable all rx/tx config flags at once. + */ +static void fsl_ssi_rxtx_config(struct fsl_ssi_private *ssi_private, + bool enable) +{ + struct regmap *regs = ssi_private->regs; + struct fsl_ssi_rxtx_reg_val *vals = &ssi_private->rxtx_reg_val; + + if (enable) { + regmap_update_bits(regs, CCSR_SSI_SIER, + vals->rx.sier | vals->tx.sier, + vals->rx.sier | vals->tx.sier); + regmap_update_bits(regs, CCSR_SSI_SRCR, + vals->rx.srcr | vals->tx.srcr, + vals->rx.srcr | vals->tx.srcr); + regmap_update_bits(regs, CCSR_SSI_STCR, + vals->rx.stcr | vals->tx.stcr, + vals->rx.stcr | vals->tx.stcr); + } else { + regmap_update_bits(regs, CCSR_SSI_SRCR, + vals->rx.srcr | vals->tx.srcr, 0); + regmap_update_bits(regs, CCSR_SSI_STCR, + vals->rx.stcr | vals->tx.stcr, 0); + regmap_update_bits(regs, CCSR_SSI_SIER, + vals->rx.sier | vals->tx.sier, 0); + } +} + +/* + * Calculate the bits that have to be disabled for the current stream that is + * getting disabled. This keeps the bits enabled that are necessary for the + * second stream to work if 'stream_active' is true. + * + * Detailed calculation: + * These are the values that need to be active after disabling. For non-active + * second stream, this is 0: + * vals_stream * !!stream_active + * + * The following computes the overall differences between the setup for the + * to-disable stream and the active stream, a simple XOR: + * vals_disable ^ (vals_stream * !!(stream_active)) + * + * The full expression adds a mask on all values we care about + */ +#define fsl_ssi_disable_val(vals_disable, vals_stream, stream_active) \ + ((vals_disable) & \ + ((vals_disable) ^ ((vals_stream) * (u32)!!(stream_active)))) + +/* + * Enable/Disable a ssi configuration. You have to pass either + * ssi_private->rxtx_reg_val.rx or tx as vals parameter. + */ +static void fsl_ssi_config(struct fsl_ssi_private *ssi_private, bool enable, + struct fsl_ssi_reg_val *vals) +{ + struct regmap *regs = ssi_private->regs; + struct fsl_ssi_reg_val *avals; + int nr_active_streams; + u32 scr_val; + int keep_active; + + regmap_read(regs, CCSR_SSI_SCR, &scr_val); + + nr_active_streams = !!(scr_val & CCSR_SSI_SCR_TE) + + !!(scr_val & CCSR_SSI_SCR_RE); + + if (nr_active_streams - 1 > 0) + keep_active = 1; + else + keep_active = 0; + + /* Find the other direction values rx or tx which we do not want to + * modify */ + if (&ssi_private->rxtx_reg_val.rx == vals) + avals = &ssi_private->rxtx_reg_val.tx; + else + avals = &ssi_private->rxtx_reg_val.rx; + + /* If vals should be disabled, start with disabling the unit */ + if (!enable) { + u32 scr = fsl_ssi_disable_val(vals->scr, avals->scr, + keep_active); + regmap_update_bits(regs, CCSR_SSI_SCR, scr, 0); + } + + /* + * We are running on a SoC which does not support online SSI + * reconfiguration, so we have to enable all necessary flags at once + * even if we do not use them later (capture and playback configuration) + */ + if (ssi_private->soc->offline_config) { + if ((enable && !nr_active_streams) || + (!enable && !keep_active)) + fsl_ssi_rxtx_config(ssi_private, enable); + + goto config_done; + } + + /* + * Configure single direction units while the SSI unit is running + * (online configuration) + */ + if (enable) { + regmap_update_bits(regs, CCSR_SSI_SIER, vals->sier, vals->sier); + regmap_update_bits(regs, CCSR_SSI_SRCR, vals->srcr, vals->srcr); + regmap_update_bits(regs, CCSR_SSI_STCR, vals->stcr, vals->stcr); + } else { + u32 sier; + u32 srcr; + u32 stcr; + + /* + * Disabling the necessary flags for one of rx/tx while the + * other stream is active is a little bit more difficult. We + * have to disable only those flags that differ between both + * streams (rx XOR tx) and that are set in the stream that is + * disabled now. Otherwise we could alter flags of the other + * stream + */ + + /* These assignments are simply vals without bits set in avals*/ + sier = fsl_ssi_disable_val(vals->sier, avals->sier, + keep_active); + srcr = fsl_ssi_disable_val(vals->srcr, avals->srcr, + keep_active); + stcr = fsl_ssi_disable_val(vals->stcr, avals->stcr, + keep_active); + + regmap_update_bits(regs, CCSR_SSI_SRCR, srcr, 0); + regmap_update_bits(regs, CCSR_SSI_STCR, stcr, 0); + regmap_update_bits(regs, CCSR_SSI_SIER, sier, 0); + } + +config_done: + /* Enabling of subunits is done after configuration */ + if (enable) + regmap_update_bits(regs, CCSR_SSI_SCR, vals->scr, vals->scr); +} + + +static void fsl_ssi_rx_config(struct fsl_ssi_private *ssi_private, bool enable) +{ + fsl_ssi_config(ssi_private, enable, &ssi_private->rxtx_reg_val.rx); +} + +static void fsl_ssi_tx_config(struct fsl_ssi_private *ssi_private, bool enable) +{ + fsl_ssi_config(ssi_private, enable, &ssi_private->rxtx_reg_val.tx); +} + +/* + * Setup rx/tx register values used to enable/disable the streams. These will + * be used later in fsl_ssi_config to setup the streams without the need to + * check for all different SSI modes. + */ +static void fsl_ssi_setup_reg_vals(struct fsl_ssi_private *ssi_private) +{ + struct fsl_ssi_rxtx_reg_val *reg = &ssi_private->rxtx_reg_val; + + reg->rx.sier = CCSR_SSI_SIER_RFF0_EN; + reg->rx.srcr = CCSR_SSI_SRCR_RFEN0; + reg->rx.scr = 0; + reg->tx.sier = CCSR_SSI_SIER_TFE0_EN; + reg->tx.stcr = CCSR_SSI_STCR_TFEN0; + reg->tx.scr = 0; + + if (!fsl_ssi_is_ac97(ssi_private)) { + reg->rx.scr = CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE; + reg->rx.sier |= CCSR_SSI_SIER_RFF0_EN; + reg->tx.scr = CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE; + reg->tx.sier |= CCSR_SSI_SIER_TFE0_EN; + } + + if (ssi_private->use_dma) { + reg->rx.sier |= CCSR_SSI_SIER_RDMAE; + reg->tx.sier |= CCSR_SSI_SIER_TDMAE; + } else { + reg->rx.sier |= CCSR_SSI_SIER_RIE; + reg->tx.sier |= CCSR_SSI_SIER_TIE; + } + + reg->rx.sier |= FSLSSI_SIER_DBG_RX_FLAGS; + reg->tx.sier |= FSLSSI_SIER_DBG_TX_FLAGS; +} + +static void fsl_ssi_setup_ac97(struct fsl_ssi_private *ssi_private) +{ + struct regmap *regs = ssi_private->regs; + + /* + * Setup the clock control register + */ + regmap_write(regs, CCSR_SSI_STCCR, + CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13)); + regmap_write(regs, CCSR_SSI_SRCCR, + CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13)); + + /* + * Enable AC97 mode and startup the SSI + */ + regmap_write(regs, CCSR_SSI_SACNT, + CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV); + regmap_write(regs, CCSR_SSI_SACCDIS, 0xff); + regmap_write(regs, CCSR_SSI_SACCEN, 0x300); + + /* + * Enable SSI, Transmit and Receive. AC97 has to communicate with the + * codec before a stream is started. + */ + regmap_update_bits(regs, CCSR_SSI_SCR, + CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE, + CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE); + + regmap_write(regs, CCSR_SSI_SOR, CCSR_SSI_SOR_WAIT(3)); +} + +/** + * fsl_ssi_startup: create a new substream + * + * This is the first function called when a stream is opened. + * + * If this is the first stream open, then grab the IRQ and program most of + * the SSI registers. + */ +static int fsl_ssi_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct fsl_ssi_private *ssi_private = + snd_soc_dai_get_drvdata(rtd->cpu_dai); + int ret; + + ret = clk_prepare_enable(ssi_private->clk); + if (ret) + return ret; + + /* When using dual fifo mode, it is safer to ensure an even period + * size. If appearing to an odd number while DMA always starts its + * task from fifo0, fifo1 would be neglected at the end of each + * period. But SSI would still access fifo1 with an invalid data. + */ + if (ssi_private->use_dual_fifo) + snd_pcm_hw_constraint_step(substream->runtime, 0, + SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2); + + return 0; +} + +/** + * fsl_ssi_shutdown: shutdown the SSI + * + */ +static void fsl_ssi_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct fsl_ssi_private *ssi_private = + snd_soc_dai_get_drvdata(rtd->cpu_dai); + + clk_disable_unprepare(ssi_private->clk); + +} + +/** + * fsl_ssi_set_bclk - configure Digital Audio Interface bit clock + * + * Note: This function can be only called when using SSI as DAI master + * + * Quick instruction for parameters: + * freq: Output BCLK frequency = samplerate * 32 (fixed) * channels + * dir: SND_SOC_CLOCK_OUT -> TxBCLK, SND_SOC_CLOCK_IN -> RxBCLK. + */ +static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream, + struct snd_soc_dai *cpu_dai, + struct snd_pcm_hw_params *hw_params) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); + struct regmap *regs = ssi_private->regs; + int synchronous = ssi_private->cpu_dai_drv.symmetric_rates, ret; + u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i; + unsigned long clkrate, baudrate, tmprate; + u64 sub, savesub = 100000; + unsigned int freq; + bool baudclk_is_used; + + /* Prefer the explicitly set bitclock frequency */ + if (ssi_private->bitclk_freq) + freq = ssi_private->bitclk_freq; + else + freq = params_channels(hw_params) * 32 * params_rate(hw_params); + + /* Don't apply it to any non-baudclk circumstance */ + if (IS_ERR(ssi_private->baudclk)) + return -EINVAL; + + baudclk_is_used = ssi_private->baudclk_streams & ~(BIT(substream->stream)); + + /* It should be already enough to divide clock by setting pm alone */ + psr = 0; + div2 = 0; + + factor = (div2 + 1) * (7 * psr + 1) * 2; + + for (i = 0; i < 255; i++) { + tmprate = freq * factor * (i + 1); + + if (baudclk_is_used) + clkrate = clk_get_rate(ssi_private->baudclk); + else + clkrate = clk_round_rate(ssi_private->baudclk, tmprate); + + /* + * Hardware limitation: The bclk rate must be + * never greater than 1/5 IPG clock rate + */ + if (clkrate * 5 > clk_get_rate(ssi_private->clk)) + continue; + + clkrate /= factor; + afreq = clkrate / (i + 1); + + if (freq == afreq) + sub = 0; + else if (freq / afreq == 1) + sub = freq - afreq; + else if (afreq / freq == 1) + sub = afreq - freq; + else + continue; + + /* Calculate the fraction */ + sub *= 100000; + do_div(sub, freq); + + if (sub < savesub) { + baudrate = tmprate; + savesub = sub; + pm = i; + } + + /* We are lucky */ + if (savesub == 0) + break; + } + + /* No proper pm found if it is still remaining the initial value */ + if (pm == 999) { + dev_err(cpu_dai->dev, "failed to handle the required sysclk\n"); + return -EINVAL; + } + + stccr = CCSR_SSI_SxCCR_PM(pm + 1) | (div2 ? CCSR_SSI_SxCCR_DIV2 : 0) | + (psr ? CCSR_SSI_SxCCR_PSR : 0); + mask = CCSR_SSI_SxCCR_PM_MASK | CCSR_SSI_SxCCR_DIV2 | + CCSR_SSI_SxCCR_PSR; + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK || synchronous) + regmap_update_bits(regs, CCSR_SSI_STCCR, mask, stccr); + else + regmap_update_bits(regs, CCSR_SSI_SRCCR, mask, stccr); + + if (!baudclk_is_used) { + ret = clk_set_rate(ssi_private->baudclk, baudrate); + if (ret) { + dev_err(cpu_dai->dev, "failed to set baudclk rate\n"); + return -EINVAL; + } + } + + return 0; +} + +static int fsl_ssi_set_dai_sysclk(struct snd_soc_dai *cpu_dai, + int clk_id, unsigned int freq, int dir) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); + + ssi_private->bitclk_freq = freq; + + return 0; +} + +/** + * fsl_ssi_hw_params - program the sample size + * + * Most of the SSI registers have been programmed in the startup function, + * but the word length must be programmed here. Unfortunately, programming + * the SxCCR.WL bits requires the SSI to be temporarily disabled. This can + * cause a problem with supporting simultaneous playback and capture. If + * the SSI is already playing a stream, then that stream may be temporarily + * stopped when you start capture. + * + * Note: The SxCCR.DC and SxCCR.PM bits are only used if the SSI is the + * clock master. + */ +static int fsl_ssi_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *hw_params, struct snd_soc_dai *cpu_dai) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); + struct regmap *regs = ssi_private->regs; + unsigned int channels = params_channels(hw_params); + unsigned int sample_size = + snd_pcm_format_width(params_format(hw_params)); + u32 wl = CCSR_SSI_SxCCR_WL(sample_size); + int ret; + u32 scr_val; + int enabled; + + regmap_read(regs, CCSR_SSI_SCR, &scr_val); + enabled = scr_val & CCSR_SSI_SCR_SSIEN; + + /* + * If we're in synchronous mode, and the SSI is already enabled, + * then STCCR is already set properly. + */ + if (enabled && ssi_private->cpu_dai_drv.symmetric_rates) + return 0; + + if (fsl_ssi_is_i2s_master(ssi_private)) { + ret = fsl_ssi_set_bclk(substream, cpu_dai, hw_params); + if (ret) + return ret; + + /* Do not enable the clock if it is already enabled */ + if (!(ssi_private->baudclk_streams & BIT(substream->stream))) { + ret = clk_prepare_enable(ssi_private->baudclk); + if (ret) + return ret; + + ssi_private->baudclk_streams |= BIT(substream->stream); + } + } + + if (!fsl_ssi_is_ac97(ssi_private)) { + u8 i2smode; + /* + * Switch to normal net mode in order to have a frame sync + * signal every 32 bits instead of 16 bits + */ + if (fsl_ssi_is_i2s_cbm_cfs(ssi_private) && sample_size == 16) + i2smode = CCSR_SSI_SCR_I2S_MODE_NORMAL | + CCSR_SSI_SCR_NET; + else + i2smode = ssi_private->i2s_mode; + + regmap_update_bits(regs, CCSR_SSI_SCR, + CCSR_SSI_SCR_NET | CCSR_SSI_SCR_I2S_MODE_MASK, + channels == 1 ? 0 : i2smode); + } + + /* + * FIXME: The documentation says that SxCCR[WL] should not be + * modified while the SSI is enabled. The only time this can + * happen is if we're trying to do simultaneous playback and + * capture in asynchronous mode. Unfortunately, I have been enable + * to get that to work at all on the P1022DS. Therefore, we don't + * bother to disable/enable the SSI when setting SxCCR[WL], because + * the SSI will stop anyway. Maybe one day, this will get fixed. + */ + + /* In synchronous mode, the SSI uses STCCR for capture */ + if ((substream->stream == SNDRV_PCM_STREAM_PLAYBACK) || + ssi_private->cpu_dai_drv.symmetric_rates) + regmap_update_bits(regs, CCSR_SSI_STCCR, CCSR_SSI_SxCCR_WL_MASK, + wl); + else + regmap_update_bits(regs, CCSR_SSI_SRCCR, CCSR_SSI_SxCCR_WL_MASK, + wl); + + return 0; +} + +static int fsl_ssi_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *cpu_dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct fsl_ssi_private *ssi_private = + snd_soc_dai_get_drvdata(rtd->cpu_dai); + + if (fsl_ssi_is_i2s_master(ssi_private) && + ssi_private->baudclk_streams & BIT(substream->stream)) { + clk_disable_unprepare(ssi_private->baudclk); + ssi_private->baudclk_streams &= ~BIT(substream->stream); + } + + return 0; +} + +static int _fsl_ssi_set_dai_fmt(struct device *dev, + struct fsl_ssi_private *ssi_private, + unsigned int fmt) +{ + struct regmap *regs = ssi_private->regs; + u32 strcr = 0, stcr, srcr, scr, mask; + u8 wm; + + ssi_private->dai_fmt = fmt; + + if (fsl_ssi_is_i2s_master(ssi_private) && IS_ERR(ssi_private->baudclk)) { + dev_err(dev, "baudclk is missing which is necessary for master mode\n"); + return -EINVAL; + } + + fsl_ssi_setup_reg_vals(ssi_private); + + regmap_read(regs, CCSR_SSI_SCR, &scr); + scr &= ~(CCSR_SSI_SCR_SYN | CCSR_SSI_SCR_I2S_MODE_MASK); + scr |= CCSR_SSI_SCR_SYNC_TX_FS; + + mask = CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFDIR | CCSR_SSI_STCR_TXDIR | + CCSR_SSI_STCR_TSCKP | CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TFSL | + CCSR_SSI_STCR_TEFS; + regmap_read(regs, CCSR_SSI_STCR, &stcr); + regmap_read(regs, CCSR_SSI_SRCR, &srcr); + stcr &= ~mask; + srcr &= ~mask; + + ssi_private->i2s_mode = CCSR_SSI_SCR_NET; + switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFS: + case SND_SOC_DAIFMT_CBS_CFS: + ssi_private->i2s_mode |= CCSR_SSI_SCR_I2S_MODE_MASTER; + regmap_update_bits(regs, CCSR_SSI_STCCR, + CCSR_SSI_SxCCR_DC_MASK, + CCSR_SSI_SxCCR_DC(2)); + regmap_update_bits(regs, CCSR_SSI_SRCCR, + CCSR_SSI_SxCCR_DC_MASK, + CCSR_SSI_SxCCR_DC(2)); + break; + case SND_SOC_DAIFMT_CBM_CFM: + ssi_private->i2s_mode |= CCSR_SSI_SCR_I2S_MODE_SLAVE; + break; + default: + return -EINVAL; + } + + /* Data on rising edge of bclk, frame low, 1clk before data */ + strcr |= CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TSCKP | + CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TEFS; + break; + case SND_SOC_DAIFMT_LEFT_J: + /* Data on rising edge of bclk, frame high */ + strcr |= CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TSCKP; + break; + case SND_SOC_DAIFMT_DSP_A: + /* Data on rising edge of bclk, frame high, 1clk before data */ + strcr |= CCSR_SSI_STCR_TFSL | CCSR_SSI_STCR_TSCKP | + CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TEFS; + break; + case SND_SOC_DAIFMT_DSP_B: + /* Data on rising edge of bclk, frame high */ + strcr |= CCSR_SSI_STCR_TFSL | CCSR_SSI_STCR_TSCKP | + CCSR_SSI_STCR_TXBIT0; + break; + case SND_SOC_DAIFMT_AC97: + ssi_private->i2s_mode |= CCSR_SSI_SCR_I2S_MODE_NORMAL; + break; + default: + return -EINVAL; + } + scr |= ssi_private->i2s_mode; + + /* DAI clock inversion */ + switch (fmt & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_NF: + /* Nothing to do for both normal cases */ + break; + case SND_SOC_DAIFMT_IB_NF: + /* Invert bit clock */ + strcr ^= CCSR_SSI_STCR_TSCKP; + break; + case SND_SOC_DAIFMT_NB_IF: + /* Invert frame clock */ + strcr ^= CCSR_SSI_STCR_TFSI; + break; + case SND_SOC_DAIFMT_IB_IF: + /* Invert both clocks */ + strcr ^= CCSR_SSI_STCR_TSCKP; + strcr ^= CCSR_SSI_STCR_TFSI; + break; + default: + return -EINVAL; + } + + /* DAI clock master masks */ + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBS_CFS: + strcr |= CCSR_SSI_STCR_TFDIR | CCSR_SSI_STCR_TXDIR; + scr |= CCSR_SSI_SCR_SYS_CLK_EN; + break; + case SND_SOC_DAIFMT_CBM_CFM: + scr &= ~CCSR_SSI_SCR_SYS_CLK_EN; + break; + case SND_SOC_DAIFMT_CBM_CFS: + strcr &= ~CCSR_SSI_STCR_TXDIR; + strcr |= CCSR_SSI_STCR_TFDIR; + scr &= ~CCSR_SSI_SCR_SYS_CLK_EN; + break; + default: + return -EINVAL; + } + + stcr |= strcr; + srcr |= strcr; + + if (ssi_private->cpu_dai_drv.symmetric_rates) { + /* Need to clear RXDIR when using SYNC mode */ + srcr &= ~CCSR_SSI_SRCR_RXDIR; + scr |= CCSR_SSI_SCR_SYN; + } + + regmap_write(regs, CCSR_SSI_STCR, stcr); + regmap_write(regs, CCSR_SSI_SRCR, srcr); + regmap_write(regs, CCSR_SSI_SCR, scr); + + /* + * Set the watermark for transmit FIFI 0 and receive FIFO 0. We don't + * use FIFO 1. We program the transmit water to signal a DMA transfer + * if there are only two (or fewer) elements left in the FIFO. Two + * elements equals one frame (left channel, right channel). This value, + * however, depends on the depth of the transmit buffer. + * + * We set the watermark on the same level as the DMA burstsize. For + * fiq it is probably better to use the biggest possible watermark + * size. + */ + if (ssi_private->use_dma) + wm = ssi_private->fifo_depth - 2; + else + wm = ssi_private->fifo_depth; + + regmap_write(regs, CCSR_SSI_SFCSR, + CCSR_SSI_SFCSR_TFWM0(wm) | CCSR_SSI_SFCSR_RFWM0(wm) | + CCSR_SSI_SFCSR_TFWM1(wm) | CCSR_SSI_SFCSR_RFWM1(wm)); + + if (ssi_private->use_dual_fifo) { + regmap_update_bits(regs, CCSR_SSI_SRCR, CCSR_SSI_SRCR_RFEN1, + CCSR_SSI_SRCR_RFEN1); + regmap_update_bits(regs, CCSR_SSI_STCR, CCSR_SSI_STCR_TFEN1, + CCSR_SSI_STCR_TFEN1); + regmap_update_bits(regs, CCSR_SSI_SCR, CCSR_SSI_SCR_TCH_EN, + CCSR_SSI_SCR_TCH_EN); + } + + if (fmt & SND_SOC_DAIFMT_AC97) + fsl_ssi_setup_ac97(ssi_private); + + return 0; + +} + +/** + * fsl_ssi_set_dai_fmt - configure Digital Audio Interface Format. + */ +static int fsl_ssi_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); + + return _fsl_ssi_set_dai_fmt(cpu_dai->dev, ssi_private, fmt); +} + +/** + * fsl_ssi_set_dai_tdm_slot - set TDM slot number + * + * Note: This function can be only called when using SSI as DAI master + */ +static int fsl_ssi_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, u32 tx_mask, + u32 rx_mask, int slots, int slot_width) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); + struct regmap *regs = ssi_private->regs; + u32 val; + + /* The slot number should be >= 2 if using Network mode or I2S mode */ + regmap_read(regs, CCSR_SSI_SCR, &val); + val &= CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_NET; + if (val && slots < 2) { + dev_err(cpu_dai->dev, "slot number should be >= 2 in I2S or NET\n"); + return -EINVAL; + } + + regmap_update_bits(regs, CCSR_SSI_STCCR, CCSR_SSI_SxCCR_DC_MASK, + CCSR_SSI_SxCCR_DC(slots)); + regmap_update_bits(regs, CCSR_SSI_SRCCR, CCSR_SSI_SxCCR_DC_MASK, + CCSR_SSI_SxCCR_DC(slots)); + + /* The register SxMSKs needs SSI to provide essential clock due to + * hardware design. So we here temporarily enable SSI to set them. + */ + regmap_read(regs, CCSR_SSI_SCR, &val); + val &= CCSR_SSI_SCR_SSIEN; + regmap_update_bits(regs, CCSR_SSI_SCR, CCSR_SSI_SCR_SSIEN, + CCSR_SSI_SCR_SSIEN); + + regmap_write(regs, CCSR_SSI_STMSK, ~tx_mask); + regmap_write(regs, CCSR_SSI_SRMSK, ~rx_mask); + + regmap_update_bits(regs, CCSR_SSI_SCR, CCSR_SSI_SCR_SSIEN, val); + + return 0; +} + +/** + * fsl_ssi_trigger: start and stop the DMA transfer. + * + * This function is called by ALSA to start, stop, pause, and resume the DMA + * transfer of data. + * + * The DMA channel is in external master start and pause mode, which + * means the SSI completely controls the flow of data. + */ +static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai); + struct regmap *regs = ssi_private->regs; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_RESUME: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + fsl_ssi_tx_config(ssi_private, true); + else + fsl_ssi_rx_config(ssi_private, true); + break; + + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_SUSPEND: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + fsl_ssi_tx_config(ssi_private, false); + else + fsl_ssi_rx_config(ssi_private, false); + break; + + default: + return -EINVAL; + } + + if (fsl_ssi_is_ac97(ssi_private)) { + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + regmap_write(regs, CCSR_SSI_SOR, CCSR_SSI_SOR_TX_CLR); + else + regmap_write(regs, CCSR_SSI_SOR, CCSR_SSI_SOR_RX_CLR); + } + + return 0; +} + +static int fsl_ssi_dai_probe(struct snd_soc_dai *dai) +{ + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(dai); + + if (ssi_private->soc->imx && ssi_private->use_dma) { + dai->playback_dma_data = &ssi_private->dma_params_tx; + dai->capture_dma_data = &ssi_private->dma_params_rx; + } + + return 0; +} + +static const struct snd_soc_dai_ops fsl_ssi_dai_ops = { + .startup = fsl_ssi_startup, + .shutdown = fsl_ssi_shutdown, + .hw_params = fsl_ssi_hw_params, + .hw_free = fsl_ssi_hw_free, + .set_fmt = fsl_ssi_set_dai_fmt, + .set_sysclk = fsl_ssi_set_dai_sysclk, + .set_tdm_slot = fsl_ssi_set_dai_tdm_slot, + .trigger = fsl_ssi_trigger, +}; + +/* Template for the CPU dai driver structure */ +static struct snd_soc_dai_driver fsl_ssi_dai_template = { + .probe = fsl_ssi_dai_probe, + .playback = { + .stream_name = "CPU-Playback", + .channels_min = 1, + .channels_max = 2, + .rates = FSLSSI_I2S_RATES, + .formats = FSLSSI_I2S_FORMATS, + }, + .capture = { + .stream_name = "CPU-Capture", + .channels_min = 1, + .channels_max = 2, + .rates = FSLSSI_I2S_RATES, + .formats = FSLSSI_I2S_FORMATS, + }, + .ops = &fsl_ssi_dai_ops, +}; + +static const struct snd_soc_component_driver fsl_ssi_component = { + .name = "fsl-ssi", +}; + +static struct snd_soc_dai_driver fsl_ssi_ac97_dai = { + .bus_control = true, + .playback = { + .stream_name = "AC97 Playback", + .channels_min = 2, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S16_LE, + }, + .capture = { + .stream_name = "AC97 Capture", + .channels_min = 2, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_S16_LE, + }, + .ops = &fsl_ssi_dai_ops, +}; + + +static struct fsl_ssi_private *fsl_ac97_data; + +static void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, + unsigned short val) +{ + struct regmap *regs = fsl_ac97_data->regs; + unsigned int lreg; + unsigned int lval; + + if (reg > 0x7f) + return; + + + lreg = reg << 12; + regmap_write(regs, CCSR_SSI_SACADD, lreg); + + lval = val << 4; + regmap_write(regs, CCSR_SSI_SACDAT, lval); + + regmap_update_bits(regs, CCSR_SSI_SACNT, CCSR_SSI_SACNT_RDWR_MASK, + CCSR_SSI_SACNT_WR); + udelay(100); +} + +static unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97, + unsigned short reg) +{ + struct regmap *regs = fsl_ac97_data->regs; + + unsigned short val = -1; + u32 reg_val; + unsigned int lreg; + + lreg = (reg & 0x7f) << 12; + regmap_write(regs, CCSR_SSI_SACADD, lreg); + regmap_update_bits(regs, CCSR_SSI_SACNT, CCSR_SSI_SACNT_RDWR_MASK, + CCSR_SSI_SACNT_RD); + + udelay(100); + + regmap_read(regs, CCSR_SSI_SACDAT, ®_val); + val = (reg_val >> 4) & 0xffff; + + return val; +} + +static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = { + .read = fsl_ssi_ac97_read, + .write = fsl_ssi_ac97_write, +}; + +/** + * Make every character in a string lower-case + */ +static void make_lowercase(char *s) +{ + char *p = s; + char c; + + while ((c = *p)) { + if ((c >= 'A') && (c <= 'Z')) + *p = c + ('a' - 'A'); + p++; + } +} + +static int fsl_ssi_imx_probe(struct platform_device *pdev, + struct fsl_ssi_private *ssi_private, void __iomem *iomem) +{ + struct device_node *np = pdev->dev.of_node; + u32 dmas[4]; + int ret; + + if (ssi_private->has_ipg_clk_name) + ssi_private->clk = devm_clk_get(&pdev->dev, "ipg"); + else + ssi_private->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(ssi_private->clk)) { + ret = PTR_ERR(ssi_private->clk); + dev_err(&pdev->dev, "could not get clock: %d\n", ret); + return ret; + } + + if (!ssi_private->has_ipg_clk_name) { + ret = clk_prepare_enable(ssi_private->clk); + if (ret) { + dev_err(&pdev->dev, "clk_prepare_enable failed: %d\n", ret); + return ret; + } + } + + /* For those SLAVE implementations, we ingore non-baudclk cases + * and, instead, abandon MASTER mode that needs baud clock. + */ + ssi_private->baudclk = devm_clk_get(&pdev->dev, "baud"); + if (IS_ERR(ssi_private->baudclk)) + dev_dbg(&pdev->dev, "could not get baud clock: %ld\n", + PTR_ERR(ssi_private->baudclk)); + + /* + * We have burstsize be "fifo_depth - 2" to match the SSI + * watermark setting in fsl_ssi_startup(). + */ + ssi_private->dma_params_tx.maxburst = ssi_private->fifo_depth - 2; + ssi_private->dma_params_rx.maxburst = ssi_private->fifo_depth - 2; + ssi_private->dma_params_tx.addr = ssi_private->ssi_phys + CCSR_SSI_STX0; + ssi_private->dma_params_rx.addr = ssi_private->ssi_phys + CCSR_SSI_SRX0; + + ret = of_property_read_u32_array(np, "dmas", dmas, 4); + if (ssi_private->use_dma && !ret && dmas[2] == IMX_DMATYPE_SSI_DUAL) { + ssi_private->use_dual_fifo = true; + /* When using dual fifo mode, we need to keep watermark + * as even numbers due to dma script limitation. + */ + ssi_private->dma_params_tx.maxburst &= ~0x1; + ssi_private->dma_params_rx.maxburst &= ~0x1; + } + + if (!ssi_private->use_dma) { + + /* + * Some boards use an incompatible codec. To get it + * working, we are using imx-fiq-pcm-audio, that + * can handle those codecs. DMA is not possible in this + * situation. + */ + + ssi_private->fiq_params.irq = ssi_private->irq; + ssi_private->fiq_params.base = iomem; + ssi_private->fiq_params.dma_params_rx = + &ssi_private->dma_params_rx; + ssi_private->fiq_params.dma_params_tx = + &ssi_private->dma_params_tx; + + ret = imx_pcm_fiq_init(pdev, &ssi_private->fiq_params); + if (ret) + goto error_pcm; + } else { + ret = imx_pcm_dma_init(pdev); + if (ret) + goto error_pcm; + } + + return 0; + +error_pcm: + + if (!ssi_private->has_ipg_clk_name) + clk_disable_unprepare(ssi_private->clk); + return ret; +} + +static void fsl_ssi_imx_clean(struct platform_device *pdev, + struct fsl_ssi_private *ssi_private) +{ + if (!ssi_private->use_dma) + imx_pcm_fiq_exit(pdev); + if (!ssi_private->has_ipg_clk_name) + clk_disable_unprepare(ssi_private->clk); +} + +static int fsl_ssi_probe(struct platform_device *pdev) +{ + struct fsl_ssi_private *ssi_private; + int ret = 0; + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *of_id; + const char *p, *sprop; + const uint32_t *iprop; + struct resource *res; + void __iomem *iomem; + char name[64]; + + /* SSIs that are not connected on the board should have a + * status = "disabled" + * property in their device tree nodes. + */ + if (!of_device_is_available(np)) + return -ENODEV; + + of_id = of_match_device(fsl_ssi_ids, &pdev->dev); + if (!of_id || !of_id->data) + return -EINVAL; + + ssi_private = devm_kzalloc(&pdev->dev, sizeof(*ssi_private), + GFP_KERNEL); + if (!ssi_private) { + dev_err(&pdev->dev, "could not allocate DAI object\n"); + return -ENOMEM; + } + + ssi_private->soc = of_id->data; + + sprop = of_get_property(np, "fsl,mode", NULL); + if (sprop) { + if (!strcmp(sprop, "ac97-slave")) + ssi_private->dai_fmt = SND_SOC_DAIFMT_AC97; + } + + ssi_private->use_dma = !of_property_read_bool(np, + "fsl,fiq-stream-filter"); + + if (fsl_ssi_is_ac97(ssi_private)) { + memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_ac97_dai, + sizeof(fsl_ssi_ac97_dai)); + + fsl_ac97_data = ssi_private; + + snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev); + } else { + /* Initialize this copy of the CPU DAI driver structure */ + memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template, + sizeof(fsl_ssi_dai_template)); + } + ssi_private->cpu_dai_drv.name = dev_name(&pdev->dev); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + iomem = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(iomem)) + return PTR_ERR(iomem); + ssi_private->ssi_phys = res->start; + + ret = of_property_match_string(np, "clock-names", "ipg"); + if (ret < 0) { + ssi_private->has_ipg_clk_name = false; + ssi_private->regs = devm_regmap_init_mmio(&pdev->dev, iomem, + &fsl_ssi_regconfig); + } else { + ssi_private->has_ipg_clk_name = true; + ssi_private->regs = devm_regmap_init_mmio_clk(&pdev->dev, + "ipg", iomem, &fsl_ssi_regconfig); + } + if (IS_ERR(ssi_private->regs)) { + dev_err(&pdev->dev, "Failed to init register map\n"); + return PTR_ERR(ssi_private->regs); + } + + ssi_private->irq = platform_get_irq(pdev, 0); + if (ssi_private->irq < 0) { + dev_err(&pdev->dev, "no irq for node %s\n", pdev->name); + return ssi_private->irq; + } + + /* Are the RX and the TX clocks locked? */ + if (!of_find_property(np, "fsl,ssi-asynchronous", NULL)) { + ssi_private->cpu_dai_drv.symmetric_rates = 1; + ssi_private->cpu_dai_drv.symmetric_channels = 1; + ssi_private->cpu_dai_drv.symmetric_samplebits = 1; + } + + /* Determine the FIFO depth. */ + iprop = of_get_property(np, "fsl,fifo-depth", NULL); + if (iprop) + ssi_private->fifo_depth = be32_to_cpup(iprop); + else + /* Older 8610 DTs didn't have the fifo-depth property */ + ssi_private->fifo_depth = 8; + + dev_set_drvdata(&pdev->dev, ssi_private); + + if (ssi_private->soc->imx) { + ret = fsl_ssi_imx_probe(pdev, ssi_private, iomem); + if (ret) + return ret; + } + + ret = devm_snd_soc_register_component(&pdev->dev, &fsl_ssi_component, + &ssi_private->cpu_dai_drv, 1); + if (ret) { + dev_err(&pdev->dev, "failed to register DAI: %d\n", ret); + goto error_asoc_register; + } + + if (ssi_private->use_dma) { + ret = devm_request_irq(&pdev->dev, ssi_private->irq, + fsl_ssi_isr, 0, dev_name(&pdev->dev), + ssi_private); + if (ret < 0) { + dev_err(&pdev->dev, "could not claim irq %u\n", + ssi_private->irq); + goto error_asoc_register; + } + } + + ret = fsl_ssi_debugfs_create(&ssi_private->dbg_stats, &pdev->dev); + if (ret) + goto error_asoc_register; + + /* + * If codec-handle property is missing from SSI node, we assume + * that the machine driver uses new binding which does not require + * SSI driver to trigger machine driver's probe. + */ + if (!of_get_property(np, "codec-handle", NULL)) + goto done; + + /* Trigger the machine driver's probe function. The platform driver + * name of the machine driver is taken from /compatible property of the + * device tree. We also pass the address of the CPU DAI driver + * structure. + */ + sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL); + /* Sometimes the compatible name has a "fsl," prefix, so we strip it. */ + p = strrchr(sprop, ','); + if (p) + sprop = p + 1; + snprintf(name, sizeof(name), "snd-soc-%s", sprop); + make_lowercase(name); + + ssi_private->pdev = + platform_device_register_data(&pdev->dev, name, 0, NULL, 0); + if (IS_ERR(ssi_private->pdev)) { + ret = PTR_ERR(ssi_private->pdev); + dev_err(&pdev->dev, "failed to register platform: %d\n", ret); + goto error_sound_card; + } + +done: + if (ssi_private->dai_fmt) + _fsl_ssi_set_dai_fmt(&pdev->dev, ssi_private, + ssi_private->dai_fmt); + + return 0; + +error_sound_card: + fsl_ssi_debugfs_remove(&ssi_private->dbg_stats); + +error_asoc_register: + if (ssi_private->soc->imx) + fsl_ssi_imx_clean(pdev, ssi_private); + + return ret; +} + +static int fsl_ssi_remove(struct platform_device *pdev) +{ + struct fsl_ssi_private *ssi_private = dev_get_drvdata(&pdev->dev); + + fsl_ssi_debugfs_remove(&ssi_private->dbg_stats); + + if (ssi_private->pdev) + platform_device_unregister(ssi_private->pdev); + + if (ssi_private->soc->imx) + fsl_ssi_imx_clean(pdev, ssi_private); + + return 0; +} + +static struct platform_driver fsl_ssi_driver = { + .driver = { + .name = "fsl-ssi-dai", + .of_match_table = fsl_ssi_ids, + }, + .probe = fsl_ssi_probe, + .remove = fsl_ssi_remove, +}; + +module_platform_driver(fsl_ssi_driver); + +MODULE_ALIAS("platform:fsl-ssi-dai"); +MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); +MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver"); +MODULE_LICENSE("GPL v2"); |