From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- Documentation/DocBook/writing_musb_glue_layer.tmpl | 873 +++++++++++++++++++++ 1 file changed, 873 insertions(+) create mode 100644 Documentation/DocBook/writing_musb_glue_layer.tmpl (limited to 'Documentation/DocBook/writing_musb_glue_layer.tmpl') diff --git a/Documentation/DocBook/writing_musb_glue_layer.tmpl b/Documentation/DocBook/writing_musb_glue_layer.tmpl new file mode 100644 index 000000000..837eca77f --- /dev/null +++ b/Documentation/DocBook/writing_musb_glue_layer.tmpl @@ -0,0 +1,873 @@ + + + + + + Writing an MUSB Glue Layer + + + + Apelete + Seketeli + +
+ apelete at seketeli.net +
+ + + + + + 2014 + Apelete Seketeli + + + + + This documentation is free software; you can redistribute it + and/or modify it under the terms of the GNU General Public + License as published by the Free Software Foundation; either + version 2 of the License, or (at your option) any later version. + + + + This documentation is distributed in the hope that it will be + useful, but WITHOUT ANY WARRANTY; without even the implied + warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU General Public License for more details. + + + + You should have received a copy of the GNU General Public License + along with this documentation; if not, write to the Free Software + Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA + 02111-1307 USA + + + + For more details see the file COPYING in the Linux kernel source + tree. + + + + + + + + Introduction + + The Linux MUSB subsystem is part of the larger Linux USB + subsystem. It provides support for embedded USB Device Controllers + (UDC) that do not use Universal Host Controller Interface (UHCI) + or Open Host Controller Interface (OHCI). + + + Instead, these embedded UDC rely on the USB On-the-Go (OTG) + specification which they implement at least partially. The silicon + reference design used in most cases is the Multipoint USB + Highspeed Dual-Role Controller (MUSB HDRC) found in the Mentor + Graphics Inventra™ design. + + + As a self-taught exercise I have written an MUSB glue layer for + the Ingenic JZ4740 SoC, modelled after the many MUSB glue layers + in the kernel source tree. This layer can be found at + drivers/usb/musb/jz4740.c. In this documentation I will walk + through the basics of the jz4740.c glue layer, explaining the + different pieces and what needs to be done in order to write your + own device glue layer. + + + + + Linux MUSB Basics + + To get started on the topic, please read USB On-the-Go Basics (see + Resources) which provides an introduction of USB OTG operation at + the hardware level. A couple of wiki pages by Texas Instruments + and Analog Devices also provide an overview of the Linux kernel + MUSB configuration, albeit focused on some specific devices + provided by these companies. Finally, getting acquainted with the + USB specification at USB home page may come in handy, with + practical instance provided through the Writing USB Device Drivers + documentation (again, see Resources). + + + Linux USB stack is a layered architecture in which the MUSB + controller hardware sits at the lowest. The MUSB controller driver + abstract the MUSB controller hardware to the Linux USB stack. + + + ------------------------ + | | <------- drivers/usb/gadget + | Linux USB Core Stack | <------- drivers/usb/host + | | <------- drivers/usb/core + ------------------------ + ⬍ + -------------------------- + | | <------ drivers/usb/musb/musb_gadget.c + | MUSB Controller driver | <------ drivers/usb/musb/musb_host.c + | | <------ drivers/usb/musb/musb_core.c + -------------------------- + ⬍ + --------------------------------- + | MUSB Platform Specific Driver | + | | <-- drivers/usb/musb/jz4740.c + | aka "Glue Layer" | + --------------------------------- + ⬍ + --------------------------------- + | MUSB Controller Hardware | + --------------------------------- + + + As outlined above, the glue layer is actually the platform + specific code sitting in between the controller driver and the + controller hardware. + + + Just like a Linux USB driver needs to register itself with the + Linux USB subsystem, the MUSB glue layer needs first to register + itself with the MUSB controller driver. This will allow the + controller driver to know about which device the glue layer + supports and which functions to call when a supported device is + detected or released; remember we are talking about an embedded + controller chip here, so no insertion or removal at run-time. + + + All of this information is passed to the MUSB controller driver + through a platform_driver structure defined in the glue layer as: + + +static struct platform_driver jz4740_driver = { + .probe = jz4740_probe, + .remove = jz4740_remove, + .driver = { + .name = "musb-jz4740", + }, +}; + + + The probe and remove function pointers are called when a matching + device is detected and, respectively, released. The name string + describes the device supported by this glue layer. In the current + case it matches a platform_device structure declared in + arch/mips/jz4740/platform.c. Note that we are not using device + tree bindings here. + + + In order to register itself to the controller driver, the glue + layer goes through a few steps, basically allocating the + controller hardware resources and initialising a couple of + circuits. To do so, it needs to keep track of the information used + throughout these steps. This is done by defining a private + jz4740_glue structure: + + +struct jz4740_glue { + struct device *dev; + struct platform_device *musb; + struct clk *clk; +}; + + + The dev and musb members are both device structure variables. The + first one holds generic information about the device, since it's + the basic device structure, and the latter holds information more + closely related to the subsystem the device is registered to. The + clk variable keeps information related to the device clock + operation. + + + Let's go through the steps of the probe function that leads the + glue layer to register itself to the controller driver. + + + N.B.: For the sake of readability each function will be split in + logical parts, each part being shown as if it was independent from + the others. + + +static int jz4740_probe(struct platform_device *pdev) +{ + struct platform_device *musb; + struct jz4740_glue *glue; + struct clk *clk; + int ret; + + glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL); + if (!glue) + return -ENOMEM; + + musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO); + if (!musb) { + dev_err(&pdev->dev, "failed to allocate musb device\n"); + return -ENOMEM; + } + + clk = devm_clk_get(&pdev->dev, "udc"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "failed to get clock\n"); + ret = PTR_ERR(clk); + goto err_platform_device_put; + } + + ret = clk_prepare_enable(clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock\n"); + goto err_platform_device_put; + } + + musb->dev.parent = &pdev->dev; + + glue->dev = &pdev->dev; + glue->musb = musb; + glue->clk = clk; + + return 0; + +err_platform_device_put: + platform_device_put(musb); + return ret; +} + + + The first few lines of the probe function allocate and assign the + glue, musb and clk variables. The GFP_KERNEL flag (line 8) allows + the allocation process to sleep and wait for memory, thus being + usable in a blocking situation. The PLATFORM_DEVID_AUTO flag (line + 12) allows automatic allocation and management of device IDs in + order to avoid device namespace collisions with explicit IDs. With + devm_clk_get() (line 18) the glue layer allocates the clock -- the + devm_ prefix indicates that clk_get() is + managed: it automatically frees the allocated clock resource data + when the device is released -- and enable it. + + + Then comes the registration steps: + + +static int jz4740_probe(struct platform_device *pdev) +{ + struct musb_hdrc_platform_data *pdata = &jz4740_musb_platform_data; + + pdata->platform_ops = &jz4740_musb_ops; + + platform_set_drvdata(pdev, glue); + + ret = platform_device_add_resources(musb, pdev->resource, + pdev->num_resources); + if (ret) { + dev_err(&pdev->dev, "failed to add resources\n"); + goto err_clk_disable; + } + + ret = platform_device_add_data(musb, pdata, sizeof(*pdata)); + if (ret) { + dev_err(&pdev->dev, "failed to add platform_data\n"); + goto err_clk_disable; + } + + return 0; + +err_clk_disable: + clk_disable_unprepare(clk); +err_platform_device_put: + platform_device_put(musb); + return ret; +} + + + The first step is to pass the device data privately held by the + glue layer on to the controller driver through + platform_set_drvdata() (line 7). Next is passing on the device + resources information, also privately held at that point, through + platform_device_add_resources() (line 9). + + + Finally comes passing on the platform specific data to the + controller driver (line 16). Platform data will be discussed in + Chapter 4, but here + we are looking at the platform_ops function pointer (line 5) in + musb_hdrc_platform_data structure (line 3). This function + pointer allows the MUSB controller driver to know which function + to call for device operation: + + +static const struct musb_platform_ops jz4740_musb_ops = { + .init = jz4740_musb_init, + .exit = jz4740_musb_exit, +}; + + + Here we have the minimal case where only init and exit functions + are called by the controller driver when needed. Fact is the + JZ4740 MUSB controller is a basic controller, lacking some + features found in other controllers, otherwise we may also have + pointers to a few other functions like a power management function + or a function to switch between OTG and non-OTG modes, for + instance. + + + At that point of the registration process, the controller driver + actually calls the init function: + + +static int jz4740_musb_init(struct musb *musb) +{ + musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); + if (!musb->xceiv) { + pr_err("HS UDC: no transceiver configured\n"); + return -ENODEV; + } + + /* Silicon does not implement ConfigData register. + * Set dyn_fifo to avoid reading EP config from hardware. + */ + musb->dyn_fifo = true; + + musb->isr = jz4740_musb_interrupt; + + return 0; +} + + + The goal of jz4740_musb_init() is to get hold of the transceiver + driver data of the MUSB controller hardware and pass it on to the + MUSB controller driver, as usual. The transceiver is the circuitry + inside the controller hardware responsible for sending/receiving + the USB data. Since it is an implementation of the physical layer + of the OSI model, the transceiver is also referred to as PHY. + + + Getting hold of the MUSB PHY driver data is done with + usb_get_phy() which returns a pointer to the structure + containing the driver instance data. The next couple of + instructions (line 12 and 14) are used as a quirk and to setup + IRQ handling respectively. Quirks and IRQ handling will be + discussed later in Chapter + 5 and Chapter 3. + + +static int jz4740_musb_exit(struct musb *musb) +{ + usb_put_phy(musb->xceiv); + + return 0; +} + + + Acting as the counterpart of init, the exit function releases the + MUSB PHY driver when the controller hardware itself is about to be + released. + + + Again, note that init and exit are fairly simple in this case due + to the basic set of features of the JZ4740 controller hardware. + When writing an musb glue layer for a more complex controller + hardware, you might need to take care of more processing in those + two functions. + + + Returning from the init function, the MUSB controller driver jumps + back into the probe function: + + +static int jz4740_probe(struct platform_device *pdev) +{ + ret = platform_device_add(musb); + if (ret) { + dev_err(&pdev->dev, "failed to register musb device\n"); + goto err_clk_disable; + } + + return 0; + +err_clk_disable: + clk_disable_unprepare(clk); +err_platform_device_put: + platform_device_put(musb); + return ret; +} + + + This is the last part of the device registration process where the + glue layer adds the controller hardware device to Linux kernel + device hierarchy: at this stage, all known information about the + device is passed on to the Linux USB core stack. + + +static int jz4740_remove(struct platform_device *pdev) +{ + struct jz4740_glue *glue = platform_get_drvdata(pdev); + + platform_device_unregister(glue->musb); + clk_disable_unprepare(glue->clk); + + return 0; +} + + + Acting as the counterpart of probe, the remove function unregister + the MUSB controller hardware (line 5) and disable the clock (line + 6), allowing it to be gated. + + + + + Handling IRQs + + Additionally to the MUSB controller hardware basic setup and + registration, the glue layer is also responsible for handling the + IRQs: + + +static irqreturn_t jz4740_musb_interrupt(int irq, void *__hci) +{ + unsigned long flags; + irqreturn_t retval = IRQ_NONE; + struct musb *musb = __hci; + + spin_lock_irqsave(&musb->lock, flags); + + musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB); + musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX); + musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX); + + /* + * The controller is gadget only, the state of the host mode IRQ bits is + * undefined. Mask them to make sure that the musb driver core will + * never see them set + */ + musb->int_usb &= MUSB_INTR_SUSPEND | MUSB_INTR_RESUME | + MUSB_INTR_RESET | MUSB_INTR_SOF; + + if (musb->int_usb || musb->int_tx || musb->int_rx) + retval = musb_interrupt(musb); + + spin_unlock_irqrestore(&musb->lock, flags); + + return retval; +} + + + Here the glue layer mostly has to read the relevant hardware + registers and pass their values on to the controller driver which + will handle the actual event that triggered the IRQ. + + + The interrupt handler critical section is protected by the + spin_lock_irqsave() and counterpart spin_unlock_irqrestore() + functions (line 7 and 24 respectively), which prevent the + interrupt handler code to be run by two different threads at the + same time. + + + Then the relevant interrupt registers are read (line 9 to 11): + + + + + MUSB_INTRUSB: indicates which USB interrupts are currently + active, + + + + + MUSB_INTRTX: indicates which of the interrupts for TX + endpoints are currently active, + + + + + MUSB_INTRRX: indicates which of the interrupts for TX + endpoints are currently active. + + + + + Note that musb_readb() is used to read 8-bit registers at most, + while musb_readw() allows us to read at most 16-bit registers. + There are other functions that can be used depending on the size + of your device registers. See musb_io.h for more information. + + + Instruction on line 18 is another quirk specific to the JZ4740 + USB device controller, which will be discussed later in Chapter 5. + + + The glue layer still needs to register the IRQ handler though. + Remember the instruction on line 14 of the init function: + + +static int jz4740_musb_init(struct musb *musb) +{ + musb->isr = jz4740_musb_interrupt; + + return 0; +} + + + This instruction sets a pointer to the glue layer IRQ handler + function, in order for the controller hardware to call the handler + back when an IRQ comes from the controller hardware. The interrupt + handler is now implemented and registered. + + + + + Device Platform Data + + In order to write an MUSB glue layer, you need to have some data + describing the hardware capabilities of your controller hardware, + which is called the platform data. + + + Platform data is specific to your hardware, though it may cover a + broad range of devices, and is generally found somewhere in the + arch/ directory, depending on your device architecture. + + + For instance, platform data for the JZ4740 SoC is found in + arch/mips/jz4740/platform.c. In the platform.c file each device of + the JZ4740 SoC is described through a set of structures. + + + Here is the part of arch/mips/jz4740/platform.c that covers the + USB Device Controller (UDC): + + +/* USB Device Controller */ +struct platform_device jz4740_udc_xceiv_device = { + .name = "usb_phy_gen_xceiv", + .id = 0, +}; + +static struct resource jz4740_udc_resources[] = { + [0] = { + .start = JZ4740_UDC_BASE_ADDR, + .end = JZ4740_UDC_BASE_ADDR + 0x10000 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = JZ4740_IRQ_UDC, + .end = JZ4740_IRQ_UDC, + .flags = IORESOURCE_IRQ, + .name = "mc", + }, +}; + +struct platform_device jz4740_udc_device = { + .name = "musb-jz4740", + .id = -1, + .dev = { + .dma_mask = &jz4740_udc_device.dev.coherent_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = ARRAY_SIZE(jz4740_udc_resources), + .resource = jz4740_udc_resources, +}; + + + The jz4740_udc_xceiv_device platform device structure (line 2) + describes the UDC transceiver with a name and id number. + + + At the time of this writing, note that + "usb_phy_gen_xceiv" is the specific name to be used for + all transceivers that are either built-in with reference USB IP or + autonomous and doesn't require any PHY programming. You will need + to set CONFIG_NOP_USB_XCEIV=y in the kernel configuration to make + use of the corresponding transceiver driver. The id field could be + set to -1 (equivalent to PLATFORM_DEVID_NONE), -2 (equivalent to + PLATFORM_DEVID_AUTO) or start with 0 for the first device of this + kind if we want a specific id number. + + + The jz4740_udc_resources resource structure (line 7) defines the + UDC registers base addresses. + + + The first array (line 9 to 11) defines the UDC registers base + memory addresses: start points to the first register memory + address, end points to the last register memory address and the + flags member defines the type of resource we are dealing with. So + IORESOURCE_MEM is used to define the registers memory addresses. + The second array (line 14 to 17) defines the UDC IRQ registers + addresses. Since there is only one IRQ register available for the + JZ4740 UDC, start and end point at the same address. The + IORESOURCE_IRQ flag tells that we are dealing with IRQ resources, + and the name "mc" is in fact hard-coded in the MUSB core + in order for the controller driver to retrieve this IRQ resource + by querying it by its name. + + + Finally, the jz4740_udc_device platform device structure (line 21) + describes the UDC itself. + + + The "musb-jz4740" name (line 22) defines the MUSB + driver that is used for this device; remember this is in fact + the name that we used in the jz4740_driver platform driver + structure in Chapter + 2. The id field (line 23) is set to -1 (equivalent to + PLATFORM_DEVID_NONE) since we do not need an id for the device: + the MUSB controller driver was already set to allocate an + automatic id in Chapter + 2. In the dev field we care for DMA related information + here. The dma_mask field (line 25) defines the width of the DMA + mask that is going to be used, and coherent_dma_mask (line 26) + has the same purpose but for the alloc_coherent DMA mappings: in + both cases we are using a 32 bits mask. Then the resource field + (line 29) is simply a pointer to the resource structure defined + before, while the num_resources field (line 28) keeps track of + the number of arrays defined in the resource structure (in this + case there were two resource arrays defined before). + + + With this quick overview of the UDC platform data at the arch/ + level now done, let's get back to the MUSB glue layer specific + platform data in drivers/usb/musb/jz4740.c: + + +static struct musb_hdrc_config jz4740_musb_config = { + /* Silicon does not implement USB OTG. */ + .multipoint = 0, + /* Max EPs scanned, driver will decide which EP can be used. */ + .num_eps = 4, + /* RAMbits needed to configure EPs from table */ + .ram_bits = 9, + .fifo_cfg = jz4740_musb_fifo_cfg, + .fifo_cfg_size = ARRAY_SIZE(jz4740_musb_fifo_cfg), +}; + +static struct musb_hdrc_platform_data jz4740_musb_platform_data = { + .mode = MUSB_PERIPHERAL, + .config = &jz4740_musb_config, +}; + + + First the glue layer configures some aspects of the controller + driver operation related to the controller hardware specifics. + This is done through the jz4740_musb_config musb_hdrc_config + structure. + + + Defining the OTG capability of the controller hardware, the + multipoint member (line 3) is set to 0 (equivalent to false) + since the JZ4740 UDC is not OTG compatible. Then num_eps (line + 5) defines the number of USB endpoints of the controller + hardware, including endpoint 0: here we have 3 endpoints + + endpoint 0. Next is ram_bits (line 7) which is the width of the + RAM address bus for the MUSB controller hardware. This + information is needed when the controller driver cannot + automatically configure endpoints by reading the relevant + controller hardware registers. This issue will be discussed when + we get to device quirks in Chapter + 5. Last two fields (line 8 and 9) are also about device + quirks: fifo_cfg points to the USB endpoints configuration table + and fifo_cfg_size keeps track of the size of the number of + entries in that configuration table. More on that later in Chapter 5. + + + Then this configuration is embedded inside + jz4740_musb_platform_data musb_hdrc_platform_data structure (line + 11): config is a pointer to the configuration structure itself, + and mode tells the controller driver if the controller hardware + may be used as MUSB_HOST only, MUSB_PERIPHERAL only or MUSB_OTG + which is a dual mode. + + + Remember that jz4740_musb_platform_data is then used to convey + platform data information as we have seen in the probe function + in Chapter 2 + + + + + Device Quirks + + Completing the platform data specific to your device, you may also + need to write some code in the glue layer to work around some + device specific limitations. These quirks may be due to some + hardware bugs, or simply be the result of an incomplete + implementation of the USB On-the-Go specification. + + + The JZ4740 UDC exhibits such quirks, some of which we will discuss + here for the sake of insight even though these might not be found + in the controller hardware you are working on. + + + Let's get back to the init function first: + + +static int jz4740_musb_init(struct musb *musb) +{ + musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); + if (!musb->xceiv) { + pr_err("HS UDC: no transceiver configured\n"); + return -ENODEV; + } + + /* Silicon does not implement ConfigData register. + * Set dyn_fifo to avoid reading EP config from hardware. + */ + musb->dyn_fifo = true; + + musb->isr = jz4740_musb_interrupt; + + return 0; +} + + + Instruction on line 12 helps the MUSB controller driver to work + around the fact that the controller hardware is missing registers + that are used for USB endpoints configuration. + + + Without these registers, the controller driver is unable to read + the endpoints configuration from the hardware, so we use line 12 + instruction to bypass reading the configuration from silicon, and + rely on a hard-coded table that describes the endpoints + configuration instead: + + +static struct musb_fifo_cfg jz4740_musb_fifo_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 64, }, +}; + + + Looking at the configuration table above, we see that each + endpoints is described by three fields: hw_ep_num is the endpoint + number, style is its direction (either FIFO_TX for the controller + driver to send packets in the controller hardware, or FIFO_RX to + receive packets from hardware), and maxpacket defines the maximum + size of each data packet that can be transmitted over that + endpoint. Reading from the table, the controller driver knows that + endpoint 1 can be used to send and receive USB data packets of 512 + bytes at once (this is in fact a bulk in/out endpoint), and + endpoint 2 can be used to send data packets of 64 bytes at once + (this is in fact an interrupt endpoint). + + + Note that there is no information about endpoint 0 here: that one + is implemented by default in every silicon design, with a + predefined configuration according to the USB specification. For + more examples of endpoint configuration tables, see musb_core.c. + + + Let's now get back to the interrupt handler function: + + +static irqreturn_t jz4740_musb_interrupt(int irq, void *__hci) +{ + unsigned long flags; + irqreturn_t retval = IRQ_NONE; + struct musb *musb = __hci; + + spin_lock_irqsave(&musb->lock, flags); + + musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB); + musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX); + musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX); + + /* + * The controller is gadget only, the state of the host mode IRQ bits is + * undefined. Mask them to make sure that the musb driver core will + * never see them set + */ + musb->int_usb &= MUSB_INTR_SUSPEND | MUSB_INTR_RESUME | + MUSB_INTR_RESET | MUSB_INTR_SOF; + + if (musb->int_usb || musb->int_tx || musb->int_rx) + retval = musb_interrupt(musb); + + spin_unlock_irqrestore(&musb->lock, flags); + + return retval; +} + + + Instruction on line 18 above is a way for the controller driver to + work around the fact that some interrupt bits used for USB host + mode operation are missing in the MUSB_INTRUSB register, thus left + in an undefined hardware state, since this MUSB controller + hardware is used in peripheral mode only. As a consequence, the + glue layer masks these missing bits out to avoid parasite + interrupts by doing a logical AND operation between the value read + from MUSB_INTRUSB and the bits that are actually implemented in + the register. + + + These are only a couple of the quirks found in the JZ4740 USB + device controller. Some others were directly addressed in the MUSB + core since the fixes were generic enough to provide a better + handling of the issues for others controller hardware eventually. + + + + + Conclusion + + Writing a Linux MUSB glue layer should be a more accessible task, + as this documentation tries to show the ins and outs of this + exercise. + + + The JZ4740 USB device controller being fairly simple, I hope its + glue layer serves as a good example for the curious mind. Used + with the current MUSB glue layers, this documentation should + provide enough guidance to get started; should anything gets out + of hand, the linux-usb mailing list archive is another helpful + resource to browse through. + + + + + Acknowledgements + + Many thanks to Lars-Peter Clausen and Maarten ter Huurne for + answering my questions while I was writing the JZ4740 glue layer + and for helping me out getting the code in good shape. + + + I would also like to thank the Qi-Hardware community at large for + its cheerful guidance and support. + + + + + Resources + + USB Home Page: + http://www.usb.org + + + linux-usb Mailing List Archives: + http://marc.info/?l=linux-usb + + + USB On-the-Go Basics: + http://www.maximintegrated.com/app-notes/index.mvp/id/1822 + + + Writing USB Device Drivers: + https://www.kernel.org/doc/htmldocs/writing_usb_driver/index.html + + + Texas Instruments USB Configuration Wiki Page: + http://processors.wiki.ti.com/index.php/Usbgeneralpage + + + Analog Devices Blackfin MUSB Configuration: + http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:musb + + + + -- cgit v1.2.3-54-g00ecf