From b4b7ff4b08e691656c9d77c758fc355833128ac0 Mon Sep 17 00:00:00 2001
From: André Fabian Silva Delgado <emulatorman@parabola.nu>
Date: Wed, 20 Jan 2016 14:01:31 -0300
Subject: Linux-libre 4.4-gnu

---
 .../devicetree/bindings/display/atmel,lcdc.txt     | 89 ++++++++++++++++++++++
 1 file changed, 89 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/atmel,lcdc.txt

(limited to 'Documentation/devicetree/bindings/display/atmel,lcdc.txt')

diff --git a/Documentation/devicetree/bindings/display/atmel,lcdc.txt b/Documentation/devicetree/bindings/display/atmel,lcdc.txt
new file mode 100644
index 000000000..ecb8da063
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/atmel,lcdc.txt
@@ -0,0 +1,89 @@
+Atmel LCDC Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible :
+	"atmel,at91sam9261-lcdc" , 
+	"atmel,at91sam9263-lcdc" ,
+	"atmel,at91sam9g10-lcdc" ,
+	"atmel,at91sam9g45-lcdc" ,
+	"atmel,at91sam9g45es-lcdc" ,
+	"atmel,at91sam9rl-lcdc" ,
+	"atmel,at32ap-lcdc"
+- reg : Should contain 1 register ranges(address and length).
+	Can contain an additional register range(address and length)
+	for fixed framebuffer memory. Useful for dedicated memories.
+- interrupts : framebuffer controller interrupt
+- display: a phandle pointing to the display node
+
+Required nodes:
+- display: a display node is required to initialize the lcd panel
+	This should be in the board dts.
+- default-mode: a videomode within the display with timing parameters
+	as specified below.
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+
+Example:
+
+	fb0: fb@0x00500000 {
+		compatible = "atmel,at91sam9g45-lcdc";
+		reg = <0x00500000 0x1000>;
+		interrupts = <23 3 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fb>;
+		display = <&display0>;
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+	};
+
+Example for fixed framebuffer memory:
+
+	fb0: fb@0x00500000 {
+		compatible = "atmel,at91sam9263-lcdc";
+		reg = <0x00700000 0x1000 0x70000000 0x200000>;
+		[...]
+	};
+
+Atmel LCDC Display
+-----------------------------------------------------
+Required properties (as per of_videomode_helper):
+
+ - atmel,dmacon: dma controller configuration
+ - atmel,lcdcon2: lcd controller configuration
+ - atmel,guard-time: lcd guard time (Delay in frame periods)
+ - bits-per-pixel: lcd panel bit-depth.
+
+Optional properties (as per of_videomode_helper):
+ - atmel,lcdcon-backlight: enable backlight
+ - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity
+ - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
+ - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
+
+Example:
+	display0: display {
+		bits-per-pixel = <32>;
+		atmel,lcdcon-backlight;
+		atmel,dmacon = <0x1>;
+		atmel,lcdcon2 = <0x80008002>;
+		atmel,guard-time = <9>;
+		atmel,lcd-wiring-mode = <1>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9000000>;
+				hactive = <480>;
+				vactive = <272>;
+				hback-porch = <1>;
+				hfront-porch = <1>;
+				vback-porch = <40>;
+				vfront-porch = <1>;
+				hsync-len = <45>;
+				vsync-len = <1>;
+			};
+		};
+	};
-- 
cgit v1.2.3-54-g00ecf