From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- .../devicetree/bindings/pci/mvebu-pci.txt | 304 +++++++++++++++++++++ 1 file changed, 304 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/mvebu-pci.txt (limited to 'Documentation/devicetree/bindings/pci/mvebu-pci.txt') diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt new file mode 100644 index 000000000..08c716b2c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -0,0 +1,304 @@ +* Marvell EBU PCIe interfaces + +Mandatory properties: + +- compatible: one of the following values: + marvell,armada-370-pcie + marvell,armada-xp-pcie + marvell,dove-pcie + marvell,kirkwood-pcie +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- bus-range: PCI bus numbers covered +- device_type, set to "pci" +- ranges: ranges describing the MMIO registers to control the PCIe + interfaces, and ranges describing the MBus windows needed to access + the memory and I/O regions of each PCIe interface. +- msi-parent: Link to the hardware entity that serves as the Message + Signaled Interrupt controller for this PCI controller. + +The ranges describing the MMIO registers have the following layout: + + 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s + +where: + + * r is a 32-bits value that gives the offset of the MMIO + registers of this PCIe interface, from the base of the internal + registers. + + * s is a 32-bits value that give the size of this MMIO + registers area. This range entry translates the '0x82000000 0 r' PCI + address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part + of the internal register window (as identified by MBUS_ID(0xf0, + 0x01)). + +The ranges describing the MBus windows have the following layout: + + 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 + +where: + + * t is the type of the MBus window (as defined by the standard PCI DT + bindings), 1 for I/O and 2 for memory. + + * s is the PCI slot that corresponds to this PCIe interface + + * w is the 'target ID' value for the MBus window + + * a the 'attribute' value for the MBus window. + +Since the location and size of the different MBus windows is not fixed in +hardware, and only determined in runtime, those ranges cover the full first +4 GB of the physical address space, and do not translate into a valid CPU +address. + +In addition, the device tree node must have sub-nodes describing each +PCIe interface, having the following mandatory properties: + +- reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. +- assigned-addresses: reference to the MMIO registers used to control + this PCIe interface. +- clocks: the clock associated to this PCIe interface +- marvell,pcie-port: the physical PCIe port number +- status: either "disabled" or "okay" +- device_type, set to "pci" +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- ranges, translating the MBus windows ranges of the parent node into + standard PCI addresses. +- interrupt-map-mask and interrupt-map, standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + +and the following optional properties: +- marvell,pcie-lane: the physical PCIe lane number, for ports having + multiple lanes. If this property is not found, we assume that the + value is 0. +- reset-gpios: optional gpio to PERST# +- reset-delay-us: delay in us to wait after reset de-assertion + +Example: + +pcie-controller { + compatible = "marvell,armada-xp-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + msi-parent = <&mpic>; + + ranges = + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ + 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ + + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ + 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ + 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ + 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ + 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ + 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ + 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ + + 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ + 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ + + 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ + 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; + + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + /* low-active PERST# reset on GPIO 25 */ + reset-gpios = <&gpio0 25 1>; + /* wait 20ms for device settle after reset deassertion */ + reset-delay-us = <20000>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + pcie@5,0 { + device_type = "pci"; + assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 9>; + status = "disabled"; + }; + + pcie@6,0 { + device_type = "pci"; + assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 + 0x81000000 0 0 0x81000000 0x6 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + status = "disabled"; + }; + + pcie@7,0 { + device_type = "pci"; + assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 + 0x81000000 0 0 0x81000000 0x7 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + pcie@8,0 { + device_type = "pci"; + assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 + 0x81000000 0 0 0x81000000 0x8 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + status = "disabled"; + }; + + pcie@9,0 { + device_type = "pci"; + assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 + 0x81000000 0 0 0x81000000 0x9 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + status = "disabled"; + }; + + pcie@10,0 { + device_type = "pci"; + assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; + reg = <0x5000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 + 0x81000000 0 0 0x81000000 0xa 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 103>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 27>; + status = "disabled"; + }; +}; -- cgit v1.2.3-54-g00ecf