From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- .../bindings/pinctrl/img,tz1090-pinctrl.txt | 227 +++++++++++++++++++++ 1 file changed, 227 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt (limited to 'Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt') diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt new file mode 100644 index 000000000..509faa87a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -0,0 +1,227 @@ +ImgTec TZ1090 pin controller + +Required properties: +- compatible: "img,tz1090-pinctrl" +- reg: Should contain the register physical address and length of the pad + configuration registers (CR_PADS_* and CR_IF_CTL0). + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + gpio pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all pins in that group). + + They also all support the some form of muxing. Any pins which are contained + in one of the mux groups (see below) can be muxed only to the functions + supported by the mux group. All other pins can be muxed to the "perip" + function which enables them with their intended peripheral. + + Different pins in the same mux group cannot be muxed to different functions, + however it is possible to mux only a subset of the pins in a mux group to a + particular function and leave the remaining pins unmuxed. This is useful if + the board connects certain pins in a group to other devices to be controlled + by GPIO, and you don't want the usual peripheral to have any control of the + pin. + + ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7, + i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out, + i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on, + scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd, + sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0, + spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0, + tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5, + tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0, + tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7, + tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts, + uart0_rxd, uart0_txd, uart1_rxd, uart1_txd. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + function: perip or those supported by pin's mux group. + + other pins: + + These other pins are part of various pin groups below, but can't be + controlled as GPIOs. They do however support bias-high-impediance, + bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided + to any of the groups below to set it for all pins in that group). + + clk_out0, clk_out1, tck, tdi, tdo, tms, trst. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + + mux groups: + + These all support function, and some support drive configs. + + afe + pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0, + ant_sel1, gain0, gain1, gain2, gain3, gain4, + gain5, gain6, gain7. + function: afe, ts_out_0. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + pdm_d + pins: pdm_d. + function: pdm_dac, usb_vbus. + sdh + pins: sdh_cd, sdh_wp, sdh_clk_in. + function: sdh, sdio. + sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, + sdio_d3. + function: sdio, sdh. + spi1_cs2 + pins: spi1_cs2. + function: spi1_cs2, usb_vbus. + tft + pins: tft_red0, tft_red1, tft_red2, tft_red3, + tft_red4, tft_red5, tft_red6, tft_red7, + tft_green0, tft_green1, tft_green2, tft_green3, + tft_green4, tft_green5, tft_green6, tft_green7, + tft_blue0, tft_blue1, tft_blue2, tft_blue3, + tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_vdden_gd, tft_panelclk, tft_blank_ls, + tft_vsync_ns, tft_hsync_nr, tft_vd12acb, + tft_pwrsave. + function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1, + lcd_trace, phy_ringosc. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + + drive groups: + + These all support input-schmitt-enable, input-schmitt-disable, + and drive-strength. + + jtag + pins: tck, trst, tdi, tdo, tms. + scb1 + pins: scb1_sdat, scb1_sclk. + scb2 + pins: scb2_sdat, scb2_sclk. + spi0 + pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din. + spi1 + pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din. + uart + pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts, + uart1_txd, uart1_rxd. + drive_i2s + pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_bclk_out, i2s_mclk. + drive_pdm + pins: clk_out0, pdm_b, pdm_a. + drive_scb0 + pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c. + drive_sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + sdh_wp, sdh_cd, sdh_clk_in. + + convenience groups: + + These are just convenient groupings of pins and don't support any drive + configs. + + uart0 + pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd. + uart1 + pins: uart1_rxd, uart1_txd. + scb0 + pins: scb0_sclk, scb0_sdat. + i2s + pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_mclk. + +Example: + + pinctrl: pinctrl@02005800 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pinctrl"; + reg = <0x02005800 0xe4>; + }; + +Example board file extract: + + &pinctrl { + uart0_default: uart0 { + uart0_cfg { + tz1090,pins = "uart0_rxd", + "uart0_txd"; + tz1090,function = "perip"; + }; + }; + tft_default: tft { + tft_cfg { + tz1090,pins = "tft"; + tz1090,function = "tft"; + }; + }; + }; + + uart@02004b00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_default>; + }; -- cgit v1.2.3-54-g00ecf