From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: AndrĂ© Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- Documentation/devicetree/bindings/sound/wm8994.txt | 78 ++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/wm8994.txt (limited to 'Documentation/devicetree/bindings/sound/wm8994.txt') diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt new file mode 100644 index 000000000..e045e90a0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -0,0 +1,78 @@ +WM1811/WM8994/WM8958 audio CODEC + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958". + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - interrupts : The interrupt line the IRQ signal for the device is + connected to. This is optional, if it is not connected then none + of the interrupt related properties should be specified. + - interrupt-controller : These devices contain interrupt controllers + and may provide interrupt services to other devices if they have an + interrupt line connected. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - clocks : A list of up to two phandle and clock specifier pairs + - clock-names : A list of clock names sorted in the same order as clocks. + Valid clock names are "MCLK1" and "MCLK2". + + - wlf,gpio-cfg : A list of GPIO configuration register values. If absent, + no configuration of these registers is performed. If any value is + over 0xffff then the register will be left as default. If present 11 + values must be supplied. + + - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or + WM8958. If absent the register defaults will be used. + + - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device. + - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device. + + - wlf,lineout1-se : If present LINEOUT1 is in single ended mode. + - wlf,lineout2-se : If present LINEOUT2 is in single ended mode. + + - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback + connected. + - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback + connected. + + - wlf,ldoena-always-driven : If present LDOENA is always driven. + +Example: + +codec: wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + + lineout1-se; + + AVDD2-supply = <®ulator>; + CPVDD-supply = <®ulator>; + DBVDD1-supply = <®ulator>; + DBVDD2-supply = <®ulator>; + DBVDD3-supply = <®ulator>; + SPKVDD1-supply = <®ulator>; + SPKVDD2-supply = <®ulator>; +}; -- cgit v1.2.3-54-g00ecf