From b4b7ff4b08e691656c9d77c758fc355833128ac0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 20 Jan 2016 14:01:31 -0300 Subject: Linux-libre 4.4-gnu --- .../bindings/usb/nvidia,tegra20-usb-phy.txt | 72 ---------------------- 1 file changed, 72 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt (limited to 'Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt') diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt deleted file mode 100644 index a9aa79fb9..000000000 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ /dev/null @@ -1,72 +0,0 @@ -Tegra SOC USB PHY - -The device node for Tegra SOC USB PHY: - -Required properties : - - compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy". - For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain - "nvidia,-usb-phy" plus at least one of the above, where is - tegra114, tegra124, tegra132, or tegra210. - - reg : Defines the following set of registers, in the order listed: - - The PHY's own register set. - Always present. - - The register set of the PHY containing the UTMI pad control registers. - Present if-and-only-if phy_type == utmi. - - phy_type : Should be one of "utmi", "ulpi" or "hsic". - - clocks : Defines the clocks listed in the clock-names property. - - clock-names : The following clock names must be present: - - reg: The clock needed to access the PHY's own registers. This is the - associated EHCI controller's clock. Always present. - - pll_u: PLL_U. Always present. - - timer: The timeout clock (clk_m). Present if phy_type == utmi. - - utmi-pads: The clock needed to access the UTMI pad control registers. - Present if phy_type == utmi. - - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). - Present if phy_type == ulpi, and ULPI link mode is in use. - - resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names : Must include the following entries: - - usb: The PHY's own reset signal. - - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control - registers. Required even if phy_type == ulpi. - -Required properties for phy_type == ulpi: - - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. - -Required PHY timing params for utmi phy, for all chips: - - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before - start of sync launches RxActive - - nvidia,elastic-limit : Variable FIFO Depth of elastic input store - - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait - before declare IDLE. - - nvidia,term-range-adj : Range adjusment on terminations - - Either one of the following for HS driver output control: - - nvidia,xcvr-setup : integer, uses the provided value. - - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read - from the on-chip fuses - If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. - - nvidia,xcvr-lsfslew : LS falling slew rate control. - - nvidia,xcvr-lsrslew : LS rising slew rate control. - -Required PHY timing params for utmi phy, only on Tegra30 and above: - - nvidia,xcvr-hsslew : HS slew rate control. - - nvidia,hssquelch-level : HS squelch detector level. - - nvidia,hsdiscon-level : HS disconnect detector level. - -Optional properties: - - nvidia,has-legacy-mode : boolean indicates whether this controller can - operate in legacy mode (as APX 2500 / 2600). In legacy mode some - registers are accessed through the APB_MISC base address instead of - the USB controller. - - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power - optimizations for the devices that are always connected. e.g. modem. - - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be - "host", "peripheral", or "otg". Defaults to "host" if not defined. - host means this is a host controller - peripheral means it is device controller - otg means it can operate as either ("on the go") - - nvidia,has-utmi-pad-registers : boolean indicates whether this controller - contains the UTMI pad control registers common to all USB controllers. - -VBUS control (required for dr_mode == otg, optional for dr_mode == host): - - vbus-supply: regulator for VBUS -- cgit v1.2.3-54-g00ecf