From 863981e96738983919de841ec669e157e6bdaeb0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Sun, 11 Sep 2016 04:34:46 -0300 Subject: Linux-libre 4.7.1-gnu --- Documentation/devicetree/bindings/arc/eznps.txt | 7 + .../bindings/arm/altera/socfpga-eccmgr.txt | 50 ++ Documentation/devicetree/bindings/arm/amlogic.txt | 3 + Documentation/devicetree/bindings/arm/arm-boards | 8 + .../devicetree/bindings/arm/atmel-at91.txt | 65 +- Documentation/devicetree/bindings/arm/cci.txt | 2 +- .../devicetree/bindings/arm/coresight.txt | 28 + Documentation/devicetree/bindings/arm/fsl.txt | 4 + .../bindings/arm/hisilicon/hisilicon.txt | 20 +- Documentation/devicetree/bindings/arm/l2c2x0.txt | 6 + .../arm/marvell/ap806-system-controller.txt | 35 + .../arm/marvell/cp110-system-controller0.txt | 83 +++ .../devicetree/bindings/arm/omap/crossbar.txt | 3 +- .../devicetree/bindings/arm/omap/omap.txt | 6 + Documentation/devicetree/bindings/arm/oxnas.txt | 9 + Documentation/devicetree/bindings/arm/pmu.txt | 3 +- Documentation/devicetree/bindings/arm/rockchip.txt | 14 +- .../bindings/arm/samsung/samsung-boards.txt | 2 + .../devicetree/bindings/arm/spear-misc.txt | 2 +- .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 92 ++- .../devicetree/bindings/arm/ux500/boards.txt | 2 +- .../bindings/ata/nvidia,tegra124-ahci.txt | 32 + .../devicetree/bindings/ata/tegra-sata.txt | 32 - Documentation/devicetree/bindings/btmrvl.txt | 29 - Documentation/devicetree/bindings/bus/ti-gpmc.txt | 135 ---- .../devicetree/bindings/clock/artpec6.txt | 41 ++ .../bindings/clock/axs10x-i2s-pll-clock.txt | 25 + .../devicetree/bindings/clock/hi3519-crg.txt | 46 ++ .../devicetree/bindings/clock/microchip,pic32.txt | 39 ++ .../bindings/clock/nvidia,tegra124-dfll.txt | 2 +- .../devicetree/bindings/clock/oxnas,stdclk.txt | 35 + .../bindings/clock/rockchip,rk3188-cru.txt | 2 +- .../bindings/clock/rockchip,rk3288-cru.txt | 2 +- .../bindings/clock/rockchip,rk3399-cru.txt | 62 ++ .../devicetree/bindings/clock/st/st,clkgen.txt | 2 +- Documentation/devicetree/bindings/clock/sunxi.txt | 6 + .../bindings/cpufreq/nvidia,tegra124-cpufreq.txt | 44 ++ .../bindings/cpufreq/tegra124-cpufreq.txt | 44 -- .../devicetree/bindings/crypto/fsl-imx-scc.txt | 21 + .../devicetree/bindings/crypto/samsung-sss.txt | 6 +- .../bindings/devfreq/event/exynos-nocp.txt | 26 + .../devicetree/bindings/devfreq/exynos-bus.txt | 409 ++++++++++++ .../devicetree/bindings/display/brcm,bcm-vc4.txt | 36 + .../bindings/display/bridge/analogix_dp.txt | 52 ++ .../bindings/display/exynos/exynos5433-decon.txt | 5 +- .../bindings/display/exynos/exynos_dp.txt | 93 +-- .../bindings/display/exynos/exynos_dsim.txt | 2 +- .../bindings/display/exynos/exynos_hdmi.txt | 27 +- .../devicetree/bindings/display/fsl,dcu.txt | 15 +- .../devicetree/bindings/display/fsl,tcon.txt | 18 + .../bindings/display/hisilicon/dw-dsi.txt | 72 ++ .../bindings/display/hisilicon/hisi-ade.txt | 64 ++ .../devicetree/bindings/display/imx/ldb.txt | 1 + .../bindings/display/mediatek/mediatek,disp.txt | 203 ++++++ .../bindings/display/mediatek/mediatek,dpi.txt | 35 + .../bindings/display/mediatek/mediatek,dsi.txt | 60 ++ .../bindings/display/panel/innolux,at070tn92.txt | 7 + .../display/panel/olimex,lcd-olinuxino-43-ts.txt | 7 + .../bindings/display/panel/ontat,yx700wv03.txt | 7 + .../bindings/display/panel/tpk,f07a-0102.txt | 8 + .../bindings/display/panel/tpk,f10a-0102.txt | 8 + .../display/rockchip/analogix_dp-rockchip.txt | 92 +++ .../devicetree/bindings/display/snps,arcpgu.txt | 35 + .../bindings/display/sunxi/sun4i-drm.txt | 258 ++++++++ .../devicetree/bindings/dma/brcm,bcm2835-dma.txt | 26 + .../devicetree/bindings/dma/fsl-imx-sdma.txt | 27 + Documentation/devicetree/bindings/dma/mv-xor.txt | 5 +- .../bindings/dma/nvidia,tegra20-apbdma.txt | 44 ++ .../bindings/dma/nvidia,tegra210-adma.txt | 55 ++ .../devicetree/bindings/dma/qcom_bam_dma.txt | 2 + Documentation/devicetree/bindings/dma/snps-dma.txt | 11 +- .../devicetree/bindings/dma/tegra20-apbdma.txt | 44 -- .../devicetree/bindings/dma/xilinx/xilinx_dma.txt | 2 +- .../devicetree/bindings/dma/xilinx/xilinx_vdma.txt | 36 +- .../devicetree/bindings/gpio/gpio-74x164.txt | 4 +- .../devicetree/bindings/gpio/gpio-mpc8xxx.txt | 20 +- .../devicetree/bindings/gpio/gpio-poweroff.txt | 36 - .../devicetree/bindings/gpio/gpio-restart.txt | 54 -- .../devicetree/bindings/gpio/gpio-xlp.txt | 3 + Documentation/devicetree/bindings/gpio/gpio.txt | 26 + .../devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt | 24 + .../bindings/gpio/microchip,pic32-gpio.txt | 2 +- .../bindings/gpio/nvidia,tegra186-gpio.txt | 161 +++++ .../devicetree/bindings/gpio/wd,mbl-gpio.txt | 38 ++ .../devicetree/bindings/gpu/nvidia,gk20a.txt | 37 +- Documentation/devicetree/bindings/hwmon/ina2xx.txt | 1 + .../devicetree/bindings/hwmon/ltc2978.txt | 1 + .../bindings/i2c/i2c-arb-gpio-challenge.txt | 4 +- .../devicetree/bindings/i2c/i2c-demux-pinctrl.txt | 3 +- .../devicetree/bindings/i2c/i2c-mux-gpio.txt | 6 +- .../devicetree/bindings/i2c/i2c-mux-pinctrl.txt | 4 +- .../devicetree/bindings/i2c/i2c-mux-reg.txt | 6 +- .../devicetree/bindings/i2c/i2c-octeon.txt | 6 + Documentation/devicetree/bindings/i2c/i2c-rcar.txt | 3 + .../devicetree/bindings/iio/accel/mma8452.txt | 3 +- .../devicetree/bindings/iio/adc/lpc1850-adc.txt | 21 + .../devicetree/bindings/iio/adc/mxs-lradc.txt | 47 ++ .../bindings/iio/adc/rockchip-saradc.txt | 6 +- .../devicetree/bindings/iio/dac/ad5592r.txt | 155 +++++ .../devicetree/bindings/iio/dac/lpc1850-dac.txt | 20 + .../devicetree/bindings/iio/imu/inv_mpu6050.txt | 13 + .../bindings/iio/magnetometer/ak8975.txt | 12 + .../bindings/iio/potentiometer/ds1803.txt | 21 + .../bindings/iio/potentiometer/mcp4131.txt | 84 +++ .../devicetree/bindings/iio/pressure/hp03.txt | 17 + .../devicetree/bindings/iio/pressure/ms5611.txt | 19 + .../devicetree/bindings/iio/st-sensors.txt | 6 + .../devicetree/bindings/input/ads7846.txt | 2 +- .../devicetree/bindings/input/gpio-keys.txt | 10 +- .../input/touchscreen/brcm,iproc-touchscreen.txt | 23 +- .../bindings/input/touchscreen/fsl-mx25-tcq.txt | 2 +- .../bindings/interrupt-controller/arm,gic-v3.txt | 34 +- .../arm,versatile-fpga-irq.txt | 2 +- .../brcm,bcm2835-armctrl-ic.txt | 4 +- .../interrupt-controller/brcm,bcm6345-l1-intc.txt | 57 ++ .../interrupt-controller/ezchip,nps400-ic.txt | 17 + .../interrupt-controller/fsl,ls-scfg-msi.txt | 30 + .../interrupt-controller/mediatek,sysirq.txt | 3 +- .../interrupt-controller/nvidia,tegra-ictlr.txt | 43 -- .../interrupt-controller/nvidia,tegra20-ictlr.txt | 43 ++ .../interrupt-controller/nxp,lpc3220-mic.txt | 70 +- .../interrupt-controller/ti,omap4-wugen-mpu | 4 +- .../devicetree/bindings/iommu/arm,smmu.txt | 1 + Documentation/devicetree/bindings/leds/common.txt | 3 + .../devicetree/bindings/leds/leds-gpio.txt | 2 + .../devicetree/bindings/media/i2c/adv7180.txt | 29 + .../devicetree/bindings/media/rcar_vin.txt | 12 +- .../devicetree/bindings/media/xilinx/video.txt | 2 +- .../bindings/memory-controllers/exynos-srom.txt | 79 +++ .../memory-controllers/nvidia,tegra-mc.txt | 116 ---- .../memory-controllers/nvidia,tegra124-emc.txt | 374 +++++++++++ .../memory-controllers/nvidia,tegra30-mc.txt | 116 ++++ .../bindings/memory-controllers/omap-gpmc.txt | 152 +++++ .../bindings/memory-controllers/tegra-emc.txt | 374 ----------- Documentation/devicetree/bindings/mfd/arizona.txt | 2 +- Documentation/devicetree/bindings/mfd/axp20x.txt | 31 +- .../devicetree/bindings/mfd/hisilicon,hi655x.txt | 27 + Documentation/devicetree/bindings/mfd/max77620.txt | 143 ++++ Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 4 +- .../devicetree/bindings/mips/brcm/soc.txt | 3 +- .../devicetree/bindings/mips/cavium/ciu3.txt | 27 + Documentation/devicetree/bindings/mips/cpu_irq.txt | 2 +- .../devicetree/bindings/misc/fsl,qoriq-mc.txt | 81 ++- .../bindings/mmc/microchip,sdhci-pic32.txt | 2 +- .../devicetree/bindings/mmc/mmc-pwrseq-emmc.txt | 2 +- .../devicetree/bindings/mmc/rockchip-dw-mshc.txt | 1 + Documentation/devicetree/bindings/mmc/sdhci-st.txt | 4 +- Documentation/devicetree/bindings/mmc/tmio_mmc.txt | 3 + .../devicetree/bindings/mmc/usdhi6rol0.txt | 6 + .../devicetree/bindings/mtd/arm-versatile.txt | 20 +- .../devicetree/bindings/mtd/atmel-nand.txt | 2 +- .../devicetree/bindings/mtd/brcm,brcmnand.txt | 3 +- .../devicetree/bindings/mtd/fsl-quadspi.txt | 3 +- .../devicetree/bindings/mtd/gpmc-nand.txt | 19 +- Documentation/devicetree/bindings/mtd/nand.txt | 46 +- .../devicetree/bindings/net/apm-xgene-enet.txt | 2 + Documentation/devicetree/bindings/net/dsa/dsa.txt | 2 - .../devicetree/bindings/net/dsa/marvell.txt | 35 + .../devicetree/bindings/net/hisilicon-hns-dsaf.txt | 57 +- .../devicetree/bindings/net/hisilicon-hns-nic.txt | 32 +- .../devicetree/bindings/net/marvell-bt-sd8xxx.txt | 56 ++ .../devicetree/bindings/net/microchip,enc28j60.txt | 59 ++ .../devicetree/bindings/net/nfc/pn533-i2c.txt | 31 + Documentation/devicetree/bindings/net/stmmac.txt | 6 +- .../devicetree/bindings/net/ti,dp83867.txt | 2 +- .../bindings/net/wireless/marvell-sd8xxx.txt | 63 ++ .../bindings/net/wireless/qcom,ath10k.txt | 23 +- Documentation/devicetree/bindings/numa.txt | 275 ++++++++ Documentation/devicetree/bindings/opp/opp.txt | 2 +- .../devicetree/bindings/pci/designware-pcie.txt | 2 +- .../devicetree/bindings/pci/fsl,imx6q-pcie.txt | 18 +- .../devicetree/bindings/pci/hisilicon-pcie.txt | 12 +- .../bindings/pci/nvidia,tegra20-pcie.txt | 224 ++++++- .../devicetree/bindings/pci/pci-armada8k.txt | 38 ++ .../devicetree/bindings/pci/pci-keystone.txt | 1 + .../devicetree/bindings/phy/bcm-ns-usb2-phy.txt | 21 + .../bindings/phy/brcm,brcmstb-sata-phy.txt | 41 -- .../devicetree/bindings/phy/brcm-sata-phy.txt | 44 ++ .../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 733 +++++++++++++++++++++ .../bindings/phy/phy-lpc18xx-usb-otg.txt | 2 +- .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 4 +- .../devicetree/bindings/phy/phy-stih41x-usb.txt | 2 +- .../devicetree/bindings/phy/rcar-gen2-phy.txt | 8 +- .../devicetree/bindings/phy/rcar-gen3-phy-usb2.txt | 12 +- .../devicetree/bindings/phy/samsung-phy.txt | 18 +- .../bindings/pinctrl/microchip,pic32-pinctrl.txt | 2 +- .../pinctrl/nvidia,tegra124-xusb-padctl.txt | 12 +- .../devicetree/bindings/pinctrl/qcom,pmic-gpio.txt | 2 +- .../bindings/pinctrl/renesas,pfc-pinctrl.txt | 4 +- .../bindings/power/qcom,coincell-charger.txt | 2 +- .../bindings/power/renesas,rcar-sysc.txt | 48 ++ .../bindings/power/reset/gpio-poweroff.txt | 36 + .../bindings/power/reset/gpio-restart.txt | 54 ++ .../bindings/power/rockchip-io-domain.txt | 4 +- .../bindings/regulator/max8973-regulator.txt | 7 + .../devicetree/bindings/regulator/palmas-pmic.txt | 8 + .../devicetree/bindings/regulator/pv88080.txt | 49 ++ .../bindings/regulator/qcom,spmi-regulator.txt | 37 ++ .../bindings/regulator/regulator-max77620.txt | 22 + .../bindings/regulator/ti-abb-regulator.txt | 10 +- .../bindings/regulator/twl-regulator.txt | 6 + .../devicetree/bindings/reset/oxnas,reset.txt | 58 ++ Documentation/devicetree/bindings/rng/hisi-rng.txt | 12 + .../devicetree/bindings/rtc/maxim-ds1302.txt | 46 ++ .../devicetree/bindings/rtc/rtc-palmas.txt | 6 +- .../devicetree/bindings/rtc/sa1100-rtc.txt | 2 +- .../devicetree/bindings/serial/arm,mps2-uart.txt | 19 + .../devicetree/bindings/serial/fsl-imx-uart.txt | 4 +- .../devicetree/bindings/serial/fsl-mxs-auart.txt | 16 +- .../bindings/serial/microchip,pic32-uart.txt | 29 + .../devicetree/bindings/serial/mvebu-uart.txt | 13 + .../devicetree/bindings/serial/serial.txt | 57 ++ .../devicetree/bindings/serial/sirf-uart.txt | 8 +- .../devicetree/bindings/soc/mediatek/auxadc.txt | 21 + .../devicetree/bindings/soc/mediatek/pwrap.txt | 1 + .../devicetree/bindings/soc/rockchip/grf.txt | 35 + .../bindings/soc/rockchip/power_domain.txt | 47 ++ .../bindings/soc/ti/keystone-navigator-qmss.txt | 6 +- .../devicetree/bindings/sound/davinci-mcbsp.txt | 51 ++ .../devicetree/bindings/sound/fsl-sai.txt | 9 +- .../devicetree/bindings/sound/max98371.txt | 17 + .../bindings/sound/mt8173-rt5650-rt5676.txt | 5 +- .../devicetree/bindings/sound/mt8173-rt5650.txt | 10 + .../bindings/sound/nvidia,tegra30-hda.txt | 2 +- .../devicetree/bindings/sound/pcm5102a.txt | 13 + .../devicetree/bindings/sound/st,sti-asoc-card.txt | 48 +- .../devicetree/bindings/sound/tas571x.txt | 10 +- .../devicetree/bindings/sound/tas5720.txt | 25 + .../bindings/spi/microchip,spi-pic32.txt | 34 + .../devicetree/bindings/spi/spi-fsl-dspi.txt | 8 +- .../devicetree/bindings/spi/sqi-pic32.txt | 18 + Documentation/devicetree/bindings/spi/ti_qspi.txt | 7 + Documentation/devicetree/bindings/sram/sram.txt | 2 +- .../bindings/staging/iio/adc/mxs-lradc.txt | 47 -- .../bindings/thermal/nvidia,tegra124-soctherm.txt | 67 ++ .../devicetree/bindings/thermal/rcar-thermal.txt | 1 - .../devicetree/bindings/thermal/tango-thermal.txt | 17 + .../devicetree/bindings/thermal/tegra-soctherm.txt | 55 -- .../bindings/thermal/thermal-generic-adc.txt | 89 +++ .../devicetree/bindings/timer/arm,mps2-timer.txt | 28 + .../bindings/timer/ezchip,nps400-timer.txt | 15 + .../devicetree/bindings/timer/snps,arc-timer.txt | 31 + .../devicetree/bindings/timer/snps,archs-gfrc.txt | 14 + .../devicetree/bindings/timer/snps,archs-rtc.txt | 14 + .../devicetree/bindings/tty/serial/mvebu-uart.txt | 13 - Documentation/devicetree/bindings/usb/dwc3.txt | 6 +- .../bindings/usb/nvidia,tegra124-xusb.txt | 120 ++++ .../devicetree/bindings/usb/qcom,dwc3.txt | 1 - Documentation/devicetree/bindings/usb/usb-xhci.txt | 1 + .../devicetree/bindings/vendor-prefixes.txt | 21 + .../devicetree/bindings/video/bridge/anx7814.txt | 40 ++ .../devicetree/bindings/watchdog/fsl-imx-wdt.txt | 4 +- .../bindings/watchdog/microchip,pic32-dmt.txt | 19 + .../bindings/watchdog/microchip,pic32-wdt.txt | 18 + .../devicetree/bindings/watchdog/renesas-wdt.txt | 25 + 255 files changed, 7782 insertions(+), 1370 deletions(-) create mode 100644 Documentation/devicetree/bindings/arc/eznps.txt create mode 100644 Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt create mode 100644 Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt create mode 100644 Documentation/devicetree/bindings/arm/oxnas.txt create mode 100644 Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt delete mode 100644 Documentation/devicetree/bindings/ata/tegra-sata.txt delete mode 100644 Documentation/devicetree/bindings/btmrvl.txt delete mode 100644 Documentation/devicetree/bindings/bus/ti-gpmc.txt create mode 100644 Documentation/devicetree/bindings/clock/artpec6.txt create mode 100644 Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt create mode 100644 Documentation/devicetree/bindings/clock/hi3519-crg.txt create mode 100644 Documentation/devicetree/bindings/clock/microchip,pic32.txt create mode 100644 Documentation/devicetree/bindings/clock/oxnas,stdclk.txt create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt create mode 100644 Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt delete mode 100644 Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt create mode 100644 Documentation/devicetree/bindings/crypto/fsl-imx-scc.txt create mode 100644 Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt create mode 100644 Documentation/devicetree/bindings/display/bridge/analogix_dp.txt create mode 100644 Documentation/devicetree/bindings/display/fsl,tcon.txt create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt create mode 100644 Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt create mode 100644 Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt create mode 100644 Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt create mode 100644 Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt create mode 100644 Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt create mode 100644 Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt create mode 100644 Documentation/devicetree/bindings/display/snps,arcpgu.txt create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt create mode 100644 Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt create mode 100644 Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt delete mode 100644 Documentation/devicetree/bindings/dma/tegra20-apbdma.txt delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-poweroff.txt delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-restart.txt create mode 100644 Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt create mode 100644 Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt create mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt create mode 100644 Documentation/devicetree/bindings/iio/dac/ad5592r.txt create mode 100644 Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt create mode 100644 Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt create mode 100644 Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt create mode 100644 Documentation/devicetree/bindings/iio/pressure/hp03.txt create mode 100644 Documentation/devicetree/bindings/iio/pressure/ms5611.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt create mode 100644 Documentation/devicetree/bindings/media/i2c/adv7180.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt delete mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt delete mode 100644 Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt create mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt create mode 100644 Documentation/devicetree/bindings/mips/cavium/ciu3.txt create mode 100644 Documentation/devicetree/bindings/net/dsa/marvell.txt create mode 100644 Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt create mode 100644 Documentation/devicetree/bindings/net/microchip,enc28j60.txt create mode 100644 Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt create mode 100644 Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt create mode 100644 Documentation/devicetree/bindings/numa.txt create mode 100644 Documentation/devicetree/bindings/pci/pci-armada8k.txt create mode 100644 Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt delete mode 100644 Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt create mode 100644 Documentation/devicetree/bindings/phy/brcm-sata-phy.txt create mode 100644 Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt create mode 100644 Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt create mode 100644 Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt create mode 100644 Documentation/devicetree/bindings/power/reset/gpio-restart.txt create mode 100644 Documentation/devicetree/bindings/regulator/pv88080.txt create mode 100644 Documentation/devicetree/bindings/reset/oxnas,reset.txt create mode 100644 Documentation/devicetree/bindings/rng/hisi-rng.txt create mode 100644 Documentation/devicetree/bindings/rtc/maxim-ds1302.txt create mode 100644 Documentation/devicetree/bindings/serial/arm,mps2-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/mvebu-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/serial.txt create mode 100644 Documentation/devicetree/bindings/soc/mediatek/auxadc.txt create mode 100644 Documentation/devicetree/bindings/soc/rockchip/grf.txt create mode 100644 Documentation/devicetree/bindings/sound/davinci-mcbsp.txt create mode 100644 Documentation/devicetree/bindings/sound/max98371.txt create mode 100644 Documentation/devicetree/bindings/sound/pcm5102a.txt create mode 100644 Documentation/devicetree/bindings/sound/tas5720.txt create mode 100644 Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt create mode 100644 Documentation/devicetree/bindings/spi/sqi-pic32.txt delete mode 100644 Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt create mode 100644 Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt create mode 100644 Documentation/devicetree/bindings/thermal/tango-thermal.txt delete mode 100644 Documentation/devicetree/bindings/thermal/tegra-soctherm.txt create mode 100644 Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt create mode 100644 Documentation/devicetree/bindings/timer/arm,mps2-timer.txt create mode 100644 Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt create mode 100644 Documentation/devicetree/bindings/timer/snps,arc-timer.txt create mode 100644 Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt create mode 100644 Documentation/devicetree/bindings/timer/snps,archs-rtc.txt delete mode 100644 Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt create mode 100644 Documentation/devicetree/bindings/video/bridge/anx7814.txt create mode 100644 Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt create mode 100644 Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt create mode 100644 Documentation/devicetree/bindings/watchdog/renesas-wdt.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/arc/eznps.txt b/Documentation/devicetree/bindings/arc/eznps.txt new file mode 100644 index 000000000..1aa50c640 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/eznps.txt @@ -0,0 +1,7 @@ +EZchip NPS Network Processor Platforms Device Tree Bindings +--------------------------------------------------------------------------- + +Appliance main board with NPS400 ASIC. + +Required root node properties: + - compatible = "ezchip,arc-nps"; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt index 885f93d14..5a6b16070 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -3,6 +3,7 @@ This driver uses the EDAC framework to implement the SOCFPGA ECC Manager. The ECC Manager counts and corrects single bit errors and counts/handles double bit errors which are uncorrectable. +Cyclone5 and Arria5 ECC Manager Required Properties: - compatible : Should be "altr,socfpga-ecc-manager" - #address-cells: must be 1 @@ -47,3 +48,52 @@ Example: interrupts = <0 178 1>, <0 179 1>; }; }; + +Arria10 SoCFPGA ECC Manager +The Arria10 SoC ECC Manager handles the IRQs for each peripheral +in a shared register instead of individual IRQs like the Cyclone5 +and Arria5. Therefore the device tree is different as well. + +Required Properties: +- compatible : Should be "altr,socfpga-a10-ecc-manager" +- altr,sysgr-syscon : phandle to Arria10 System Manager Block + containing the ECC manager registers. +- #address-cells: must be 1 +- #size-cells: must be 1 +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. +- ranges : standard definition, should translate from local addresses + +Subcomponents: + +L2 Cache ECC +Required Properties: +- compatible : Should be "altr,socfpga-a10-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. + +On-Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-a10-ocram-ecc" +- reg : Address and size for ECC block registers. + +Example: + + eccmgr: eccmgr@ffd06000 { + compatible = "altr,socfpga-a10-ecc-manager"; + altr,sysmgr-syscon = <&sysmgr>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>, + <0 0 IRQ_TYPE_LEVEL_HIGH>; + ranges; + + l2-ecc@ffd06010 { + compatible = "altr,socfpga-a10-l2-ecc"; + reg = <0xffd06010 0x4>; + }; + + ocram-ecc@ff8c3000 { + compatible = "altr,socfpga-a10-ocram-ecc"; + reg = <0xff8c3000 0x90>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 8a5122ab1..fcc6f6c10 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -25,3 +25,6 @@ Board compatible values: - "tronsmart,vega-s95-pro", "tronsmart,vega-s95" (Meson gxbb) - "tronsmart,vega-s95-meta", "tronsmart,vega-s95" (Meson gxbb) - "tronsmart,vega-s95-telos", "tronsmart,vega-s95" (Meson gxbb) + - "hardkernel,odroid-c2" (Meson gxbb) + - "amlogic,p200" (Meson gxbb) + - "amlogic,p201" (Meson gxbb) diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 0226bc2cc..ab318a56f 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -93,6 +93,14 @@ Required nodes: a core-module with regs and the compatible strings "arm,core-module-versatile", "syscon" +Optional nodes: + +- arm,versatile-ib2-syscon : if the Versatile has an IB2 interface + board mounted, this has a separate system controller that is + defined in this node. + Required properties: + compatible = "arm,versatile-ib2-syscon", "syscon" + ARM RealView Boards ------------------- The RealView boards cover tailored evaluation boards that are used to explore diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 7fd64ec9e..e1f5ad855 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -41,6 +41,10 @@ compatible: must be one of: - "atmel,sama5d43" - "atmel,sama5d44" +Chipid required properties: +- compatible: Should be "atmel,sama5d2-chipid" +- reg : Should contain registers location and length + PIT Timer required properties: - compatible: Should be "atmel,at91sam9260-pit" - reg: Should contain registers location and length @@ -147,6 +151,65 @@ Example: clocks = <&clk32k>; }; +SHDWC SAMA5D2-Compatible Shutdown Controller + +1) shdwc node + +required properties: +- compatible: should be "atmel,sama5d2-shdwc". +- reg: should contain registers location and length +- clocks: phandle to input clock. +- #address-cells: should be one. The cell is the wake-up input index. +- #size-cells: should be zero. + +optional properties: + +- debounce-delay-us: minimum wake-up inputs debouncer period in + microseconds. It's usually a board-related property. +- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up. + +The node contains child nodes for each wake-up input that the platform uses. + +2) input nodes + +Wake-up input nodes are usually described in the "board" part of the Device +Tree. Note also that input 0 is linked to the wake-up pin and is frequently +used. + +Required properties: +- reg: should contain the wake-up input index [0 - 15]. + +Optional properties: +- atmel,wakeup-active-high: boolean, the corresponding wake-up input described + by the child, forces the wake-up of the core power supply on a high level. + The default is to be active low. + +Example: + +On the SoC side: + shdwc@f8048010 { + compatible = "atmel,sama5d2-shdwc"; + reg = <0xf8048010 0x10>; + clocks = <&clk32k>; + #address-cells = <1>; + #size-cells = <0>; + atmel,wakeup-rtc-timer; + }; + +On the board side: + shdwc@f8048010 { + debounce-delay-us = <976>; + + input@0 { + reg = <0>; + }; + + input@1 { + reg = <1>; + atmel,wakeup-active-high; + }; + }; + Special Function Registers (SFR) Special Function Registers (SFR) manage specific aspects of the integrated @@ -155,7 +218,7 @@ elsewhere. required properties: - compatible: Should be "atmel,-sfr", "syscon". - can be "sama5d3" or "sama5d4". + can be "sama5d3", "sama5d4" or "sama5d2". - reg: Should contain registers location and length sfr@f0038000 { diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index a1a5a7ecc..0f2153e8f 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -100,7 +100,7 @@ specific to ARM. "arm,cci-400-pmu,r0" "arm,cci-400-pmu,r1" "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has - secure acces to CCI registers + secure access to CCI registers "arm,cci-500-pmu,r0" "arm,cci-550-pmu,r0" - reg: diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 62938eb96..93147c0c8 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -19,6 +19,7 @@ its hardware characteristcs. - "arm,coresight-etm3x", "arm,primecell"; - "arm,coresight-etm4x", "arm,primecell"; - "qcom,coresight-replicator1x", "arm,primecell"; + - "arm,coresight-stm", "arm,primecell"; [1] * reg: physical base address and length of the register set(s) of the component. @@ -36,6 +37,14 @@ its hardware characteristcs. layout using the generic DT graph presentation found in "bindings/graph.txt". +* Additional required properties for System Trace Macrocells (STM): + * reg: along with the physical base address and length of the register + set as described above, another entry is required to describe the + mapping of the extended stimulus port area. + + * reg-names: the only acceptable values are "stm-base" and + "stm-stimulus-base", each corresponding to the areas defined in "reg". + * Required properties for devices that don't show up on the AMBA bus, such as non-configurable replicators: @@ -202,3 +211,22 @@ Example: }; }; }; + +4. STM + stm@20100000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x20100000 0 0x1000>, + <0 0x28000000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + port { + stm_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port2>; + }; + }; + }; + +[1]. There is currently two version of STM: STM32 and STM500. Both +have the same HW interface and as such don't need an explicit binding name. diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 752a685d9..dbbc09520 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -135,6 +135,10 @@ LS1043A ARMv8 based RDB Board Required root node properties: - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; +LS1043A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls1043a-qds", "fsl,ls1043a"; + LS2080A ARMv8 based Simulator model Required root node properties: - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index e3ccab114..83fe816ae 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -1,29 +1,33 @@ Hisilicon Platforms Device Tree Bindings ---------------------------------------------------- -Hi6220 SoC -Required root node properties: - - compatible = "hisilicon,hi6220"; - Hi4511 Board Required root node properties: - compatible = "hisilicon,hi3620-hi4511"; -HiP04 D01 Board +Hi6220 SoC Required root node properties: - - compatible = "hisilicon,hip04-d01"; + - compatible = "hisilicon,hi6220"; + +HiKey Board +Required root node properties: + - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; HiP01 ca9x2 Board Required root node properties: - compatible = "hisilicon,hip01-ca9x2"; -HiKey Board +HiP04 D01 Board Required root node properties: - - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; + - compatible = "hisilicon,hip04-d01"; HiP05 D02 Board Required root node properties: - compatible = "hisilicon,hip05-d02"; +HiP06 D03 Board +Required root node properties: + - compatible = "hisilicon,hip06-d03"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt index fe0398c5c..c453ab555 100644 --- a/Documentation/devicetree/bindings/arm/l2c2x0.txt +++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt @@ -84,6 +84,12 @@ Optional properties: - prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable), <1> (forcibly enable), property absent (retain settings set by firmware) +- arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly + disable), <1> (forcibly enable), property absent (OS specific behavior, + preferrably retain firmware settings) +- arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable), + <1> (forcibly enable), property absent (OS specific behavior, + preferrably retain firmware settings) Example: diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt new file mode 100644 index 000000000..8968371d8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt @@ -0,0 +1,35 @@ +Marvell Armada AP806 System Controller +====================================== + +The AP806 is one of the two core HW blocks of the Marvell Armada 7K/8K +SoCs. It contains a system controller, which provides a number +registers giving access to numerous features: clocks, pin-muxing and +many other SoC configuration items. This DT binding allows to describe +this system controller. + +The Device Tree node representing the AP806 system controller provides +a number of clocks: + + - 0: clock of CPU cluster 0 + - 1: clock of CPU cluster 1 + - 2: fixed PLL at 1200 Mhz + - 3: MSS clock, derived from the fixed PLL + +Required properties: + + - compatible: must be: + "marvell,ap806-system-controller", "syscon" + - reg: register area of the AP806 system controller + - #clock-cells: must be set to 1 + - clock-output-names: must be defined to: + "ap-cpu-cluster-0", "ap-cpu-cluster-1", "ap-fixed", "ap-mss" + +Example: + + syscon: system-controller@6f4000 { + compatible = "marvell,ap806-system-controller", "syscon"; + #clock-cells = <1>; + clock-output-names = "ap-cpu-cluster-0", "ap-cpu-cluster-1", + "ap-fixed", "ap-mss"; + reg = <0x6f4000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt new file mode 100644 index 000000000..30c546900 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt @@ -0,0 +1,83 @@ +Marvell Armada CP110 System Controller 0 +======================================== + +The CP110 is one of the two core HW blocks of the Marvell Armada 7K/8K +SoCs. It contains two sets of system control registers, System +Controller 0 and System Controller 1. This Device Tree binding allows +to describe the first system controller, which provides registers to +configure various aspects of the SoC. + +The Device Tree node representing this System Controller 0 provides a +number of clocks: + + - a set of core clocks + - a set of gatable clocks + +Those clocks can be referenced by other Device Tree nodes using two +cells: + - The first cell must be 0 or 1. 0 for the core clocks and 1 for the + gatable clocks. + - The second cell identifies the particular core clock or gatable + clocks. + +The following clocks are available: + - Core clocks + - 0 0 APLL + - 0 1 PPv2 core + - 0 2 EIP + - 0 3 Core + - 0 4 NAND core + - Gatable clocks + - 1 0 Audio + - 1 1 Comm Unit + - 1 2 NAND + - 1 3 PPv2 + - 1 4 SDIO + - 1 5 MG Domain + - 1 6 MG Core + - 1 7 XOR1 + - 1 8 XOR0 + - 1 9 GOP DP + - 1 11 PCIe x1 0 + - 1 12 PCIe x1 1 + - 1 13 PCIe x4 + - 1 14 PCIe / XOR + - 1 15 SATA + - 1 16 SATA USB + - 1 17 Main + - 1 18 SD/MMC + - 1 21 Slow IO (SPI, NOR, BootROM, I2C, UART) + - 1 22 USB3H0 + - 1 23 USB3H1 + - 1 24 USB3 Device + - 1 25 EIP150 + - 1 26 EIP197 + +Required properties: + + - compatible: must be: + "marvell,cp110-system-controller0", "syscon"; + - reg: register area of the CP110 system controller 0 + - #clock-cells: must be set to 2 + - core-clock-output-names must be set to: + "cpm-apll", "cpm-ppv2-core", "cpm-eip", "cpm-core", "cpm-nand-core" + - gate-clock-output-names must be set to: + "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", + "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", + "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; + +Example: + + cpm_syscon0: system-controller@440000 { + compatible = "marvell,cp110-system-controller0", "syscon"; + reg = <0x440000 0x1000>; + #clock-cells = <2>; + core-clock-output-names = "cpm-apll", "cpm-ppv2-core", "cpm-eip", "cpm-core", "cpm-nand-core"; + gate-clock-output-names = "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", + "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", + "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt index a9b28d74d..bb5727ae0 100644 --- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt @@ -42,7 +42,8 @@ Examples: Consumer: ======== See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and -Documentation/devicetree/bindings/arm/gic.txt for further details. +Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt for +further details. An interrupt consumer on an SoC using crossbar will use: interrupts = diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 21e71a5e8..94b57f247 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -133,6 +133,9 @@ Boards: - AM335X Bone : Low cost community board compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" +- AM3359 ICEv2 : Low cost Industrial Communication Engine EVM. + compatible = "ti,am3359-icev2", "ti,am33xx", "ti,omap3" + - AM335X OrionLXm : Substation Automation Platform compatible = "novatech,am335x-lxm", "ti,am33xx" @@ -169,6 +172,9 @@ Boards: - AM57XX SBC-AM57x compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5728 IDK + compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt new file mode 100644 index 000000000..b9e49711b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/oxnas.txt @@ -0,0 +1,9 @@ +Oxford Semiconductor OXNAS SoCs Family device tree bindings +------------------------------------------- + +Boards with the OX810SE SoC shall have the following properties: + Required root node property: + compatible: "oxsemi,ox810se" + +Board compatible values: + - "wd,mbwe" (OX810SE) diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 6eb73be94..74d5417d0 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -22,10 +22,11 @@ Required properties: "arm,arm11mpcore-pmu" "arm,arm1176-pmu" "arm,arm1136-pmu" + "brcm,vulcan-pmu" + "cavium,thunder-pmu" "qcom,scorpion-pmu" "qcom,scorpion-mp-pmu" "qcom,krait-pmu" - "cavium,thunder-pmu" - interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu interrupt (PPI) then 1 interrupt should be specified. diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 078c14fcd..715d960d5 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -39,6 +39,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- GeekBuying GeekBox: + Required root node properties: + - compatible = "geekbuying,geekbox", "rockchip,rk3368"; + - Google Brain (dev-board): Required root node properties: - compatible = "google,veyron-brain-rev0", "google,veyron-brain", @@ -87,6 +91,10 @@ Rockchip platforms device tree bindings "google,veyron-speedy-rev3", "google,veyron-speedy-rev2", "google,veyron-speedy", "google,veyron", "rockchip,rk3288"; +- mqmaker MiQi: + Required root node properties: + - compatible = "mqmaker,miqi", "rockchip,rk3288"; + - Rockchip RK3368 evb: Required root node properties: - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368"; @@ -97,4 +105,8 @@ Rockchip platforms device tree bindings - Rockchip RK3228 Evaluation board: Required root node properties: - - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; + - compatible = "rockchip,rk3228-evb", "rockchip,rk3228"; + +- Rockchip RK3399 evb: + Required root node properties: + - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 12129c011..f5deace2b 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -2,6 +2,8 @@ Required root node properties: - compatible = should be one or more of the following. + - "samsung,artik5" - for Exynos3250-based Samsung ARTIK5 module. + - "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board. - "samsung,monk" - for Exynos3250-based Samsung Simband board. - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. diff --git a/Documentation/devicetree/bindings/arm/spear-misc.txt b/Documentation/devicetree/bindings/arm/spear-misc.txt index cf649827f..e404e2556 100644 --- a/Documentation/devicetree/bindings/arm/spear-misc.txt +++ b/Documentation/devicetree/bindings/arm/spear-misc.txt @@ -6,4 +6,4 @@ few properties of different peripheral controllers. misc node required properties: - compatible Should be "st,spear1340-misc", "syscon". -- reg: Address range of misc space upto 8K +- reg: Address range of misc space up to 8K diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index 02c27004d..a74b37b07 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -1,16 +1,20 @@ NVIDIA Tegra Power Management Controller (PMC) +== Power Management Controller Node == + The PMC block interacts with an external Power Management Unit. The PMC mostly controls the entry and exit of the system from different sleep modes. It provides power-gating controllers for SoC and CPU power-islands. Required properties: - name : Should be pmc -- compatible : For Tegra20, must contain "nvidia,tegra20-pmc". For Tegra30, - must contain "nvidia,tegra30-pmc". For Tegra114, must contain - "nvidia,tegra114-pmc". For Tegra124, must contain "nvidia,tegra124-pmc". - Otherwise, must contain "nvidia,-pmc", plus at least one of the - above, where is tegra132. +- compatible : Should contain one of the following: + For Tegra20 must contain "nvidia,tegra20-pmc". + For Tegra30 must contain "nvidia,tegra30-pmc". + For Tegra114 must contain "nvidia,tegra114-pmc" + For Tegra124 must contain "nvidia,tegra124-pmc" + For Tegra132 must contain "nvidia,tegra124-pmc" + For Tegra210 must contain "nvidia,tegra210-pmc" - reg : Offset and length of the register set for the device - clocks : Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. @@ -68,6 +72,11 @@ Optional properties for hardware-triggered thermal reset (inside 'i2c-thermtrip' Defaults to 0. Valid values are described in section 12.5.2 "Pinmux Support" of the Tegra4 Technical Reference Manual. +Optional nodes: +- powergates : This node contains a hierarchy of power domain nodes, which + should match the powergates on the Tegra SoC. See "Powergate + Nodes" below. + Example: / SoC dts including file @@ -113,3 +122,76 @@ pmc@7000f400 { }; ... }; + + +== Powergate Nodes == + +Each of the powergate nodes represents a power-domain on the Tegra SoC +that can be power-gated by the Tegra PMC. The name of the powergate node +should be one of the below. Note that not every powergate is applicable +to all Tegra devices and the following list shows which powergates are +applicable to which devices. Please refer to the Tegra TRM for more +details on the various powergates. + + Name Description Devices Applicable + 3d 3D Graphics Tegra20/114/124/210 + 3d0 3D Graphics 0 Tegra30 + 3d1 3D Graphics 1 Tegra30 + aud Audio Tegra210 + dfd Debug Tegra210 + dis Display A Tegra114/124/210 + disb Display B Tegra114/124/210 + heg 2D Graphics Tegra30/114/124/210 + iram Internal RAM Tegra124/210 + mpe MPEG Encode All + nvdec NVIDIA Video Decode Engine Tegra210 + nvjpg NVIDIA JPEG Engine Tegra210 + pcie PCIE Tegra20/30/124/210 + sata SATA Tegra30/124/210 + sor Display interfaces Tegra124/210 + ve2 Video Encode Engine 2 Tegra210 + venc Video Encode Engine All + vdec Video Decode Engine Tegra20/30/114/124 + vic Video Imaging Compositor Tegra124/210 + xusba USB Partition A Tegra114/124/210 + xusbb USB Partition B Tegra114/124/210 + xusbc USB Partition C Tegra114/124/210 + +Required properties: + - clocks: Must contain an entry for each clock required by the PMC for + controlling a power-gate. See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each reset required by the PMC for + controlling a power-gate. See ../reset/reset.txt for details. + - #power-domain-cells: Must be 0. + +Example: + + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + + powergates { + pd_audio: aud { + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + resets = <&tegra_car 198>; + #power-domain-cells = <0>; + }; + }; + }; + + +== Powergate Clients == + +Hardware blocks belonging to a power domain should contain a "power-domains" +property that is a phandle pointing to the corresponding powergate node. + +Example: + + adma: adma@702e2000 { + ... + power-domains = <&pd_audio>; + ... + }; diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt index b8737a8de..7334c2462 100644 --- a/Documentation/devicetree/bindings/arm/ux500/boards.txt +++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt @@ -23,7 +23,7 @@ scu: see binding for arm/scu.txt interrupt-controller: - see binding for arm/gic.txt + see binding for interrupt-controller/arm,gic.txt timer: see binding for arm/twd.txt diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt new file mode 100644 index 000000000..66c83c3e8 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt @@ -0,0 +1,32 @@ +Tegra124 SoC SATA AHCI controller + +Required properties : +- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". Otherwise, + must contain '"nvidia,-ahci", "nvidia,tegra124-ahci"', where + is tegra132. +- reg : Should contain 2 entries: + - AHCI register set (SATA BAR5) + - SATA register set +- interrupts : Defines the interrupt used by SATA +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - sata + - sata-oob + - cml1 + - pll_e +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sata + - sata-oob + - sata-cold +- phys : Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names : Must include the following entries: + - sata-phy : XUSB PADCTL SATA PHY +- hvdd-supply : Defines the SATA HVDD regulator +- vddio-supply : Defines the SATA VDDIO regulator +- avdd-supply : Defines the SATA AVDD regulator +- target-5v-supply : Defines the SATA 5V power regulator +- target-12v-supply : Defines the SATA 12V power regulator diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt deleted file mode 100644 index 66c83c3e8..000000000 --- a/Documentation/devicetree/bindings/ata/tegra-sata.txt +++ /dev/null @@ -1,32 +0,0 @@ -Tegra124 SoC SATA AHCI controller - -Required properties : -- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". Otherwise, - must contain '"nvidia,-ahci", "nvidia,tegra124-ahci"', where - is tegra132. -- reg : Should contain 2 entries: - - AHCI register set (SATA BAR5) - - SATA register set -- interrupts : Defines the interrupt used by SATA -- clocks : Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names : Must include the following entries: - - sata - - sata-oob - - cml1 - - pll_e -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include the following entries: - - sata - - sata-oob - - sata-cold -- phys : Must contain an entry for each entry in phy-names. - See ../phy/phy-bindings.txt for details. -- phy-names : Must include the following entries: - - sata-phy : XUSB PADCTL SATA PHY -- hvdd-supply : Defines the SATA HVDD regulator -- vddio-supply : Defines the SATA VDDIO regulator -- avdd-supply : Defines the SATA AVDD regulator -- target-5v-supply : Defines the SATA 5V power regulator -- target-12v-supply : Defines the SATA 12V power regulator diff --git a/Documentation/devicetree/bindings/btmrvl.txt b/Documentation/devicetree/bindings/btmrvl.txt deleted file mode 100644 index 58f964bb0..000000000 --- a/Documentation/devicetree/bindings/btmrvl.txt +++ /dev/null @@ -1,29 +0,0 @@ -btmrvl ------- - -Required properties: - - - compatible : must be "btmrvl,cfgdata" - -Optional properties: - - - btmrvl,cal-data : Calibration data downloaded to the device during - initialization. This is an array of 28 values(u8). - - - btmrvl,gpio-gap : gpio and gap (in msecs) combination to be - configured. - -Example: - -GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs -in below example. - -btmrvl { - compatible = "btmrvl,cfgdata"; - - btmrvl,cal-data = /bits/ 8 < - 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 - 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 - 0x00 0x00 0xf0 0x00>; - btmrvl,gpio-gap = <0x0d64>; -}; diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt deleted file mode 100644 index 016837070..000000000 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ /dev/null @@ -1,135 +0,0 @@ -Device tree bindings for OMAP general purpose memory controllers (GPMC) - -The actual devices are instantiated from the child nodes of a GPMC node. - -Required properties: - - - compatible: Should be set to one of the following: - - ti,omap2420-gpmc (omap2420) - ti,omap2430-gpmc (omap2430) - ti,omap3430-gpmc (omap3430 & omap3630) - ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) - ti,am3352-gpmc (am335x devices) - - - reg: A resource specifier for the register space - (see the example below) - - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is - completed. - - #address-cells: Must be set to 2 to allow memory address translation - - #size-cells: Must be set to 1 to allow CS address passing - - gpmc,num-cs: The maximum number of chip-select lines that controller - can support. - - gpmc,num-waitpins: The maximum number of wait pins that controller can - support. - - ranges: Must be set up to reflect the memory layout with four - integer values for each chip-select line in use: - - 0 - - Currently, calculated values derived from the contents - of the per-CS register GPMC_CONFIG7 (as set up by the - bootloader) are used for the physical address decoding. - As this will change in the future, filling correct - values here is a requirement. - -Timing properties for child nodes. All are optional and default to 0. - - - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds - - Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2: - - gpmc,cs-on-ns: Assertion time - - gpmc,cs-rd-off-ns: Read deassertion time - - gpmc,cs-wr-off-ns: Write deassertion time - - ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3: - - gpmc,adv-on-ns: Assertion time - - gpmc,adv-rd-off-ns: Read deassertion time - - gpmc,adv-wr-off-ns: Write deassertion time - - gpmc,adv-aad-mux-on-ns: Assertion time for AAD - - gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD - - gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD - - WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - - gpmc,we-on-ns Assertion time - - gpmc,we-off-ns: Deassertion time - - OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - - gpmc,oe-on-ns: Assertion time - - gpmc,oe-off-ns: Deassertion time - - gpmc,oe-aad-mux-on-ns: Assertion time for AAD - - gpmc,oe-aad-mux-off-ns: Deassertion time for AAD - - Access time and cycle time timings (in nanoseconds) corresponding to - GPMC_CONFIG5: - - gpmc,page-burst-access-ns: Multiple access word delay - - gpmc,access-ns: Start-cycle to first data valid delay - - gpmc,rd-cycle-ns: Total read cycle time - - gpmc,wr-cycle-ns: Total write cycle time - - gpmc,bus-turnaround-ns: Turn-around time between successive accesses - - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses - - gpmc,clk-activation-ns: GPMC clock activation time - - gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid - data - -Boolean timing parameters. If property is present parameter enabled and -disabled if omitted: - - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock - - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock - - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive - accesses to a different CS - - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive - accesses to the same CS - - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock - - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock - - gpmc,time-para-granularity: Multiply all access times by 2 - -The following are only applicable to OMAP3+ and AM335x: - - gpmc,wr-access-ns: In synchronous write mode, for single or - burst accesses, defines the number of - GPMC_FCLK cycles from start access time - to the GPMC_CLK rising edge used by the - memory device for the first data capture. - - gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies - the time when the first data is driven on - the address-data bus. - -GPMC chip-select settings properties for child nodes. All are optional. - -- gpmc,burst-length Page/burst length. Must be 4, 8 or 16. -- gpmc,burst-wrap Enables wrap bursting -- gpmc,burst-read Enables read page/burst mode -- gpmc,burst-write Enables write page/burst mode -- gpmc,device-width Total width of device(s) connected to a GPMC - chip-select in bytes. The GPMC supports 8-bit - and 16-bit devices and so this property must be - 1 or 2. -- gpmc,mux-add-data Address and data multiplexing configuration. - Valid values are 1 for address-address-data - multiplexing mode and 2 for address-data - multiplexing mode. -- gpmc,sync-read Enables synchronous read. Defaults to asynchronous - is this is not set. -- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous - is this is not set. -- gpmc,wait-pin Wait-pin used by client. Must be less than - "gpmc,num-waitpins". -- gpmc,wait-on-read Enables wait monitoring on reads. -- gpmc,wait-on-write Enables wait monitoring on writes. - -Example for an AM33xx board: - - gpmc: gpmc@50000000 { - compatible = "ti,am3352-gpmc"; - ti,hwmods = "gpmc"; - reg = <0x50000000 0x2000>; - interrupts = <100>; - - gpmc,num-cs = <8>; - gpmc,num-waitpins = <2>; - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ - - /* child nodes go here */ - }; diff --git a/Documentation/devicetree/bindings/clock/artpec6.txt b/Documentation/devicetree/bindings/clock/artpec6.txt new file mode 100644 index 000000000..dff9cdf00 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/artpec6.txt @@ -0,0 +1,41 @@ +* Clock bindings for Axis ARTPEC-6 chip + +The bindings are based on the clock provider binding in +Documentation/devicetree/bindings/clock/clock-bindings.txt + +External clocks: +---------------- + +There are two external inputs to the main clock controller which should be +provided using the common clock bindings. +- "sys_refclk": External 50 Mhz oscillator (required) +- "i2s_refclk": Alternate audio reference clock (optional). + +Main clock controller +--------------------- + +Required properties: +- #clock-cells: Should be <1> + See dt-bindings/clock/axis,artpec6-clkctrl.h for the list of valid identifiers. +- compatible: Should be "axis,artpec6-clkctrl" +- reg: Must contain the base address and length of the system controller +- clocks: Must contain a phandle entry for each clock in clock-names +- clock-names: Must include the external oscillator ("sys_refclk"). Optional + ones are the audio reference clock ("i2s_refclk") and the audio fractional + dividers ("frac_clk0" and "frac_clk1"). + +Examples: + +ext_clk: ext_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <50000000>; +}; + +clkctrl: clkctrl@f8000000 { + #clock-cells = <1>; + compatible = "axis,artpec6-clkctrl"; + reg = <0xf8000000 0x48>; + clocks = <&ext_clk>; + clock-names = "sys_refclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt new file mode 100644 index 000000000..5ffc8df7e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt @@ -0,0 +1,25 @@ +Binding for the AXS10X I2S PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "snps,axs10x-i2s-pll-clock" +- reg : address and length of the I2S PLL register set. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + pll_clock: pll_clock { + compatible = "fixed-clock"; + clock-frequency = <27000000>; + #clock-cells = <0>; + }; + + i2s_clock@100a0 { + compatible = "snps,axs10x-i2s-pll-clock"; + reg = <0x100a0 0x10>; + clocks = <&pll_clock>; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/hi3519-crg.txt b/Documentation/devicetree/bindings/clock/hi3519-crg.txt new file mode 100644 index 000000000..acd1f235d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3519-crg.txt @@ -0,0 +1,46 @@ +* Hisilicon Hi3519 Clock and Reset Generator(CRG) + +The Hi3519 CRG module provides clock and reset signals to various +controllers within the SoC. + +This binding uses the following bindings: + Documentation/devicetree/bindings/clock/clock-bindings.txt + Documentation/devicetree/bindings/reset/reset.txt + +Required Properties: + +- compatible: should be one of the following. + - "hisilicon,hi3519-crg" - controller compatible with Hi3519 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in . + +- #reset-cells: should be 2. + +A reset signal can be controlled by writing a bit register in the CRG module. +The reset specifier consists of two cells. The first cell represents the +register offset relative to the base address. The second cell represents the +bit index in the register. + +Example: CRG nodes +CRG: clock-reset-controller@12010000 { + compatible = "hisilicon,hi3519-crg"; + reg = <0x12010000 0x10000>; + #clock-cells = <1>; + #reset-cells = <2>; +}; + +Example: consumer nodes +i2c0: i2c@12110000 { + compatible = "hisilicon,hi3519-i2c"; + reg = <0x12110000 0x1000>; + clocks = <&CRG HI3519_I2C0_RST>; + resets = <&CRG 0xe4 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt new file mode 100644 index 000000000..c93d88fdd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt @@ -0,0 +1,39 @@ +Microchip PIC32 Clock Controller Binding +---------------------------------------- +Microchip clock controller is consists of few oscillators, PLL, multiplexer +and few divider modules. + +This binding uses common clock bindings. +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "microchip,pic32mzda-clk". +- reg: shall contain base address and length of clock registers. +- #clock-cells: shall be 1. + +Optional properties: +- microchip,pic32mzda-sosc: shall be added only if platform has + secondary oscillator connected. + +Example: + rootclk: clock-controller@1f801200 { + compatible = "microchip,pic32mzda-clk"; + reg = <0x1f801200 0x200>; + #clock-cells = <1>; + /* optional */ + microchip,pic32mzda-sosc; + }; + + +The clock consumer shall specify the desired clock-output of the clock +controller (as defined in [2]) by specifying output-id in its "clock" +phandle cell. +[2] include/dt-bindings/clock/microchip,pic32-clock.h + +For example for UART2: +uart2: serial@2 { + compatible = "microchip,pic32mzda-uart"; + reg = <>; + interrupts = <>; + clocks = <&rootclk PB2CLK>; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index ee7e5fd4a..63f9d8277 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -50,7 +50,7 @@ Required properties for I2C mode: Example: -clock@0,70110000 { +clock@70110000 { compatible = "nvidia,tegra124-dfll"; reg = <0 0x70110000 0 0x100>, /* DFLL control */ <0 0x70110000 0 0x100>, /* I2C output control */ diff --git a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt new file mode 100644 index 000000000..208cca6ac --- /dev/null +++ b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt @@ -0,0 +1,35 @@ +Oxford Semiconductor OXNAS SoC Family Standard Clocks +================================================ + +Please also refer to clock-bindings.txt in this directory for common clock +bindings usage. + +Required properties: +- compatible: Should be "oxsemi,ox810se-stdclk" +- #clock-cells: 1, see below + +Parent node should have the following properties : +- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + +For OX810SE, the clock indices are : + - 0: LEON + - 1: DMA_SGDMA + - 2: CIPHER + - 3: SATA + - 4: AUDIO + - 5: USBMPH + - 6: ETHA + - 7: PCIA + - 8: NAND + +example: + +sys: sys-ctrl@000000 { + compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"; + reg = <0x000000 0x100000>; + + stdclk: stdclk { + compatible = "oxsemi,ox810se-stdclk"; + #clock-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt index 0c2bf5eba..7f368530a 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -16,7 +16,7 @@ Required Properties: Optional Properties: - rockchip,grf: phandle to the syscon managing the "general register files" - If missing pll rates are not changable, due to the missing pll lock status. + If missing pll rates are not changeable, due to the missing pll lock status. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt index c9fbb7657..8cb47c39b 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -15,7 +15,7 @@ Required Properties: Optional Properties: - rockchip,grf: phandle to the syscon managing the "general register files" - If missing pll rates are not changable, due to the missing pll lock status. + If missing pll rates are not changeable, due to the missing pll lock status. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt new file mode 100644 index 000000000..3888dd33f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt @@ -0,0 +1,62 @@ +* Rockchip RK3399 Clock and Reset Unit + +The RK3399 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: PMU for CRU should be "rockchip,rk3399-pmucru" +- compatible: CRU should be "rockchip,rk3399-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "clkin_gmac" - external GMAC clock - optional, + - "clkin_i2s" - external I2S clock - optional, + - "pclkin_cif" - external ISP clock - optional, + - "clk_usbphy0_480m" - output clock of the pll in the usbphy0 + - "clk_usbphy1_480m" - output clock of the pll in the usbphy1 + +Example: Clock controller node: + + pmucru: pmu-clock-controller@ff750000 { + compatible = "rockchip,rk3399-pmucru"; + reg = <0x0 0xff750000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3399-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff1a0000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff180000 0x0 0x100>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index 78978f1f5..b18bf86f9 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -40,7 +40,7 @@ address is common of all subnode. }; This binding uses the common clock binding[1]. -Each subnode should use the binding discribe in [2]..[7] +Each subnode should use the binding described in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 834436fbe..8f7619d8c 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -10,6 +10,7 @@ Required properties: "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 + "allwinner,sun4i-a10-pll3-clk" - for the video PLL clock on A10 "allwinner,sun9i-a80-pll4-clk" - for the peripheral PLLs on A80 "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock @@ -63,7 +64,9 @@ Required properties: "allwinner,sun8i-a83t-bus-gates-clk" - for the bus gates on A83T "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3 "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80 + "allwinner,sun4i-a10-display-clk" - for the display clocks on the A10 "allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10 + "allwinner,sun5i-a13-dram-gates-clk" - for the DRAM gates on A13 "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 "allwinner,sun4i-a10-mmc-clk" - for the MMC clock "allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80 @@ -73,6 +76,8 @@ Required properties: "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 + "allwinner,sun4i-a10-tcon-ch0-clk" - for the TCON channel 0 clock on the A10 + "allwinner,sun4i-a10-tcon-ch1-clk" - for the TCON channel 1 clock on the A10 "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 @@ -81,6 +86,7 @@ Required properties: "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock + "allwinner,sun6i-a31-display-clk" - for the display clocks Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt new file mode 100644 index 000000000..b1669fbfb --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt @@ -0,0 +1,44 @@ +Tegra124 CPU frequency scaling driver bindings +---------------------------------------------- + +Both required and optional properties listed below must be defined +under node /cpus/cpu@0. + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - cpu_g: Clock mux for the fast CPU cluster. + - cpu_lp: Clock mux for the low-power CPU cluster. + - pll_x: Fast PLL clocksource. + - pll_p: Auxiliary PLL used during fast PLL rate changes. + - dfll: Fast DFLL clocksource that also automatically scales CPU voltage. +- vdd-cpu-supply: Regulator for CPU voltage + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, + in unit of nanoseconds. + +Example: +-------- +cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + + clocks = <&tegra_car TEGRA124_CLK_CCLK_G>, + <&tegra_car TEGRA124_CLK_CCLK_LP>, + <&tegra_car TEGRA124_CLK_PLL_X>, + <&tegra_car TEGRA124_CLK_PLL_P>, + <&dfll>; + clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll"; + clock-latency = <300000>; + vdd-cpu-supply: <&vdd_cpu>; + }; + + <...> +}; diff --git a/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt deleted file mode 100644 index b1669fbfb..000000000 --- a/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt +++ /dev/null @@ -1,44 +0,0 @@ -Tegra124 CPU frequency scaling driver bindings ----------------------------------------------- - -Both required and optional properties listed below must be defined -under node /cpus/cpu@0. - -Required properties: -- clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - cpu_g: Clock mux for the fast CPU cluster. - - cpu_lp: Clock mux for the low-power CPU cluster. - - pll_x: Fast PLL clocksource. - - pll_p: Auxiliary PLL used during fast PLL rate changes. - - dfll: Fast DFLL clocksource that also automatically scales CPU voltage. -- vdd-cpu-supply: Regulator for CPU voltage - -Optional properties: -- clock-latency: Specify the possible maximum transition latency for clock, - in unit of nanoseconds. - -Example: --------- -cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <0>; - - clocks = <&tegra_car TEGRA124_CLK_CCLK_G>, - <&tegra_car TEGRA124_CLK_CCLK_LP>, - <&tegra_car TEGRA124_CLK_PLL_X>, - <&tegra_car TEGRA124_CLK_PLL_P>, - <&dfll>; - clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll"; - clock-latency = <300000>; - vdd-cpu-supply: <&vdd_cpu>; - }; - - <...> -}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-imx-scc.txt b/Documentation/devicetree/bindings/crypto/fsl-imx-scc.txt new file mode 100644 index 000000000..7aad448e8 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/fsl-imx-scc.txt @@ -0,0 +1,21 @@ +Freescale Security Controller (SCC) + +Required properties: +- compatible : Should be "fsl,imx25-scc". +- reg : Should contain register location and length. +- interrupts : Should contain interrupt numbers for SCM IRQ and SMN IRQ. +- interrupt-names : Should specify the names "scm" and "smn" for the + SCM IRQ and SMN IRQ. +- clocks: Should contain the clock driving the SCC core. +- clock-names: Should be set to "ipg". + +Example: + + scc: crypto@53fac000 { + compatible = "fsl,imx25-scc"; + reg = <0x53fac000 0x4000>; + clocks = <&clks 111>; + clock-names = "ipg"; + interrupts = <49>, <50>; + interrupt-names = "scm", "smn"; + }; diff --git a/Documentation/devicetree/bindings/crypto/samsung-sss.txt b/Documentation/devicetree/bindings/crypto/samsung-sss.txt index a6dafa83c..7a5ca5668 100644 --- a/Documentation/devicetree/bindings/crypto/samsung-sss.txt +++ b/Documentation/devicetree/bindings/crypto/samsung-sss.txt @@ -23,10 +23,8 @@ Required properties: - "samsung,exynos4210-secss" for Exynos4210, Exynos4212, Exynos4412, Exynos5250, Exynos5260 and Exynos5420 SoCs. - reg : Offset and length of the register set for the module -- interrupts : interrupt specifiers of SSS module interrupts, should contain - following entries: - - first : feed control interrupt (required for all variants), - - second : hash interrupt (required only for samsung,s5pv210-secss). +- interrupts : interrupt specifiers of SSS module interrupts (one feed + control interrupt). - clocks : list of clock phandle and specifier pairs for all clocks listed in clock-names property. diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt new file mode 100644 index 000000000..fd459f00a --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt @@ -0,0 +1,26 @@ + +* Samsung Exynos NoC (Network on Chip) Probe device + +The Samsung Exynos542x SoC has NoC (Network on Chip) Probe for NoC bus. +NoC provides the primitive values to get the performance data. The packets +that the Network on Chip (NoC) probes detects are transported over +the network infrastructure to observer units. You can configure probes to +capture packets with header or data on the data request response network, +or as traffic debug or statistic collectors. Exynos542x bus has multiple +NoC probes to provide bandwidth information about behavior of the SoC +that you can use while analyzing system performance. + +Required properties: +- compatible: Should be "samsung,exynos5420-nocp" +- reg: physical base address of each NoC Probe and length of memory mapped region. + +Optional properties: +- clock-names : the name of clock used by the NoC Probe, "nocp" +- clocks : phandles for clock specified in "clock-names" property + +Example : NoC Probe nodes in Device Tree are listed below. + + nocp_mem0_0: nocp@10CA1000 { + compatible = "samsung,exynos5420-nocp"; + reg = <0x10CA1000 0x200>; + }; diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt new file mode 100644 index 000000000..d3ec8e676 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -0,0 +1,409 @@ +* Generic Exynos Bus frequency device + +The Samsung Exynos SoC has many buses for data transfer between DRAM +and sub-blocks in SoC. Most Exynos SoCs share the common architecture +for buses. Generally, each bus of Exynos SoC includes a source clock +and a power line, which are able to change the clock frequency +of the bus in runtime. To monitor the usage of each bus in runtime, +the driver uses the PPMU (Platform Performance Monitoring Unit), which +is able to measure the current load of sub-blocks. + +The Exynos SoC includes the various sub-blocks which have the each AXI bus. +The each AXI bus has the owned source clock but, has not the only owned +power line. The power line might be shared among one more sub-blocks. +So, we can divide into two type of device as the role of each sub-block. +There are two type of bus devices as following: +- parent bus device +- passive bus device + +Basically, parent and passive bus device share the same power line. +The parent bus device can only change the voltage of shared power line +and the rest bus devices (passive bus device) depend on the decision of +the parent bus device. If there are three blocks which share the VDD_xxx +power line, Only one block should be parent device and then the rest blocks +should depend on the parent device as passive device. + + VDD_xxx |--- A block (parent) + |--- B block (passive) + |--- C block (passive) + +There are a little different composition among Exynos SoC because each Exynos +SoC has different sub-blocks. Therefore, such difference should be specified +in devicetree file instead of each device driver. In result, this driver +is able to support the bus frequency for all Exynos SoCs. + +Required properties for all bus devices: +- compatible: Should be "samsung,exynos-bus". +- clock-names : the name of clock used by the bus, "bus". +- clocks : phandles for clock specified in "clock-names" property. +- operating-points-v2: the OPP table including frequency/voltage information + to support DVFS (Dynamic Voltage/Frequency Scaling) feature. + +Required properties only for parent bus device: +- vdd-supply: the regulator to provide the buses with the voltage. +- devfreq-events: the devfreq-event device to monitor the current utilization + of buses. + +Required properties only for passive bus device: +- devfreq: the parent bus device. + +Optional properties only for parent bus device: +- exynos,saturation-ratio: the percentage value which is used to calibrate + the performance count against total cycle count. +- exynos,voltage-tolerance: the percentage value for bus voltage tolerance + which is used to calculate the max voltage. + +Detailed correlation between sub-blocks and power line according to Exynos SoC: +- In case of Exynos3250, there are two power line as following: + VDD_MIF |--- DMC + + VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC + |--- G3D + |--- RIGHTBUS + |--- PERIR + |--- FSYS + |--- LCD0 + |--- PERIR + |--- ISP + |--- CAM + +- In case of Exynos4210, there is one power line as following: + VDD_INT |--- DMC (parent device) + |--- LEFTBUS + |--- PERIL + |--- MFC(L) + |--- G3D + |--- TV + |--- LCD0 + |--- RIGHTBUS + |--- PERIR + |--- MFC(R) + |--- CAM + |--- FSYS + |--- GPS + |--- LCD0 + |--- LCD1 + +- In case of Exynos4x12, there are two power line as following: + VDD_MIF |--- DMC + + VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC(L) + |--- G3D + |--- TV + |--- IMAGE + |--- RIGHTBUS + |--- PERIR + |--- MFC(R) + |--- CAM + |--- FSYS + |--- GPS + |--- LCD0 + |--- ISP + +- In case of Exynos5422, there are two power line as following: + VDD_MIF |--- DREX 0 (parent device, DRAM EXpress controller) + |--- DREX 1 + + VDD_INT |--- NoC_Core (parent device) + |--- G2D + |--- G3D + |--- DISP1 + |--- NoC_WCORE + |--- GSCL + |--- MSCL + |--- ISP + |--- MFC + |--- GEN + |--- PERIS + |--- PERIC + |--- FSYS + |--- FSYS2 + +Example1: + Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to + power line (regulator). The MIF (Memory Interface) AXI bus is used to + transfer data between DRAM and CPU and uses the VDD_MIF regulator. + + - MIF (Memory Interface) block + : VDD_MIF |--- DMC (Dynamic Memory Controller) + + - INT (Internal) block + : VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC + |--- G3D + |--- RIGHTBUS + |--- FSYS + |--- LCD0 + |--- PERIR + |--- ISP + |--- CAM + + - MIF bus's frequency/voltage table + ----------------------- + |Lv| Freq | Voltage | + ----------------------- + |L1| 50000 |800000 | + |L2| 100000 |800000 | + |L3| 134000 |800000 | + |L4| 200000 |825000 | + |L5| 400000 |875000 | + ----------------------- + + - INT bus's frequency/voltage table + ---------------------------------------------------------- + |Block|LEFTBUS|RIGHTBUS|MCUISP |ISP |PERIL ||VDD_INT | + | name| |LCD0 | | | || | + | | |FSYS | | | || | + | | |MFC | | | || | + ---------------------------------------------------------- + |Mode |*parent|passive |passive|passive|passive|| | + ---------------------------------------------------------- + |Lv |Frequency ||Voltage | + ---------------------------------------------------------- + |L1 |50000 |50000 |50000 |50000 |50000 ||900000 | + |L2 |80000 |80000 |80000 |80000 |80000 ||900000 | + |L3 |100000 |100000 |100000 |100000 |100000 ||1000000 | + |L4 |134000 |134000 |200000 |200000 | ||1000000 | + |L5 |200000 |200000 |400000 |300000 | ||1000000 | + ---------------------------------------------------------- + +Example2 : + The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi + is listed below: + + bus_dmc: bus_dmc { + compatible = "samsung,exynos-bus"; + clocks = <&cmu_dmc CLK_DIV_DMC>; + clock-names = "bus"; + operating-points-v2 = <&bus_dmc_opp_table>; + status = "disabled"; + }; + + bus_dmc_opp_table: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + opp-microvolt = <800000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <800000>; + }; + opp@134000000 { + opp-hz = /bits/ 64 <134000000>; + opp-microvolt = <800000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + opp-microvolt = <825000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <875000>; + }; + }; + + bus_leftbus: bus_leftbus { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_GDL>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_rightbus: bus_rightbus { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_GDR>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_lcd0: bus_lcd0 { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_160>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_fsys: bus_fsys { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_200>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_mcuisp: bus_mcuisp { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>; + clock-names = "bus"; + operating-points-v2 = <&bus_mcuisp_opp_table>; + status = "disabled"; + }; + + bus_isp: bus_isp { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_266>; + clock-names = "bus"; + operating-points-v2 = <&bus_isp_opp_table>; + status = "disabled"; + }; + + bus_peril: bus_peril { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_100>; + clock-names = "bus"; + operating-points-v2 = <&bus_peril_opp_table>; + status = "disabled"; + }; + + bus_mfc: bus_mfc { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_SCLK_MFC>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_leftbus_opp_table: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + opp-microvolt = <900000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + opp-microvolt = <900000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <1000000>; + }; + opp@134000000 { + opp-hz = /bits/ 64 <134000000>; + opp-microvolt = <1000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + opp-microvolt = <1000000>; + }; + }; + + bus_mcuisp_opp_table: opp_table2 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + }; + }; + + bus_isp_opp_table: opp_table3 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + }; + opp@300000000 { + opp-hz = /bits/ 64 <300000000>; + }; + }; + + bus_peril_opp_table: opp_table4 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + }; + + + Usage case to handle the frequency and voltage of bus on runtime + in exynos3250-rinato.dts is listed below: + + &bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; /* VDD_MIF */ + status = "okay"; + }; + + &bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; + }; + + &bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_lcd0 { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_mcuisp { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_isp { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_peril { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index 9f97df4d5..a5ea451e6 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -35,12 +35,22 @@ Optional properties for HDMI: as an interrupt/status bit in the HDMI controller itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt +Required properties for DPI: +- compatible: Should be "brcm,bcm2835-dpi" +- reg: Physical base address and length of the registers +- clocks: a) core: The core clock the unit runs on + b) pixel: The pixel clock that feeds the pixelvalve +- port: Port node with a single endpoint connecting to the panel + device, as defined in [1] + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers - interrupts: The interrupt number See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +[1] Documentation/devicetree/bindings/media/video-interfaces.txt + Example: pixelvalve@7e807000 { compatible = "brcm,bcm2835-pixelvalve2"; @@ -66,6 +76,22 @@ hdmi: hdmi@7e902000 { clock-names = "pixel", "hdmi"; }; +dpi: dpi@7e208000 { + compatible = "brcm,bcm2835-dpi"; + reg = <0x7e208000 0x8c>; + clocks = <&clocks BCM2835_CLOCK_VPU>, + <&clocks BCM2835_CLOCK_DPI>; + clock-names = "core", "pixel"; + #address-cells = <1>; + #size-cells = <0>; + + port { + dpi_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; @@ -75,3 +101,13 @@ v3d: v3d@7ec00000 { vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; + +panel: panel { + compatible = "ontat,yx700wv03", "simple-panel"; + + port { + panel_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt new file mode 100644 index 000000000..4f2ba8c13 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt @@ -0,0 +1,52 @@ +Analogix Display Port bridge bindings + +Required properties for dp-controller: + -compatible: + platform specific such as: + * "samsung,exynos5-dp" + * "rockchip,rk3288-dp" + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -interrupt-parent: + phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + +Optional properties for dp-controller: + -force-hpd: + Indicate driver need force hpd when hpd detect failed, this + is used for some eDP screen which don't have hpd signal. + -hpd-gpios: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug detection + -port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/display/exynos/exynos_dp.txt + * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt +------------------------------------------------------------------------------- + +Example: + + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index 377afbf51..c9fd7b380 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -5,7 +5,8 @@ Exynos series of SoCs which transfers the image data from a video memory buffer to an external LCD interface. Required properties: -- compatible: value should be "samsung,exynos5433-decon"; +- compatible: value should be one of: + "samsung,exynos5433-decon", "samsung,exynos5433-decon-tv"; - reg: physical base address and length of the DECON registers set. - interrupts: should contain a list of all DECON IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier format @@ -16,7 +17,7 @@ Required properties: - clocks: must include clock specifiers corresponding to entries in the clock-names property. - clock-names: list of clock names sorted in the same order as the clocks - property. Must contain "aclk_decon", "aclk_smmu_decon0x", + property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index fe4a7a2de..ade5d8eeb 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -1,20 +1,3 @@ -Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP) - -DisplayPort is industry standard to accommodate the growing board adoption -of digital display technology within the PC and CE industries. -It consolidates the internal and external connection methods to reduce device -complexity and cost. It also supports necessary features for important cross -industry applications and provides performance scalability to enable the next -generation of displays that feature higher color depths, refresh rates, and -display resolutions. - -eDP (embedded display port) device is compliant with Embedded DisplayPort -standard as follows, -- DisplayPort standard 1.1a for Exynos5250 and Exynos5260. -- DisplayPort standard 1.3 for Exynos5422s and Exynos5800. - -eDP resides between FIMD and panel or FIMD and bridge such as LVDS. - The Exynos display port interface should be configured based on the type of panel connected to it. @@ -48,26 +31,6 @@ Required properties for dp-controller: from general PHY binding: the phandle for the PHY device. -phy-names: from general PHY binding: Should be "dp". - -samsung,color-space: - input video data format. - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 - -samsung,dynamic-range: - dynamic range for input video data. - VESA = 0, CEA = 1 - -samsung,ycbcr-coeff: - YCbCr co-efficients for input video. - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 - -samsung,color-depth: - number of bits per colour component. - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 - -samsung,link-rate: - link rate supported by the panel. - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A - -samsung,lane-count: - number of lanes supported by the panel. - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 - - display-timings: timings for the connected panel as described by - Documentation/devicetree/bindings/display/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -83,17 +46,31 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection -Video interfaces: - Device node can contain video interface port nodes according to [1]. - The following are properties specific to those nodes: - - endpoint node connected to bridge or panel node: - - remote-endpoint: specifies the endpoint in panel or bridge node. - This node is required in all kinds of exynos dp - to represent the connection between dp and bridge - or dp and panel. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + -video interfaces: Device node can contain video interface port + nodes according to [1]. + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/panel/display-timing.txt + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt + -phys (required) + -phy-names (required) + -hpd-gpios (optional) + force-hpd (optional) + +Deprecated properties for DisplayPort: +-interlaced: deprecated prop that can parsed from drm_display_mode. +-vsync-active-high: deprecated prop that can parsed from drm_display_mode. +-hsync-active-high: deprecated prop that can parsed from drm_display_mode. +-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode. +-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode. +-samsung,color-space: deprecated prop that can parsed from drm_display_info. +-samsung,color-depth: deprecated prop that can parsed from drm_display_info. +-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method. +-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method. +-samsung,hpd-gpio: deprecated name for hpd-gpios. + +------------------------------------------------------------------------------- Example: @@ -112,13 +89,6 @@ SOC specific portion: Board Specific portion: dp-controller { - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <4>; - display-timings { native-mode = <&lcd_timing>; lcd_timing: 1366x768 { @@ -135,18 +105,9 @@ Board Specific portion: }; ports { - port { + port@0 { dp_out: endpoint { - remote-endpoint = <&dp_in>; - }; - }; - }; - - panel { - ... - port { - dp_in: endpoint { - remote-endpoint = <&dp_out>; + remote-endpoint = <&bridge_in>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 22756b3de..a78265993 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -41,7 +41,7 @@ Video interfaces: endpoint node connected from mic node (reg = 0): - remote-endpoint: specifies the endpoint in mic node. This node is required for Exynos5433 mipi dsi. So mic can access to panel node - thoughout this dsi node. + throughout this dsi node. endpoint node connected to panel node (reg = 1): - remote-endpoint: specifies the endpoint in panel node. This node is required in all kinds of exynos mipi dsi to represent diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index d474f59be..a2ec4c1c9 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -5,6 +5,7 @@ Required properties: 1) "samsung,exynos4210-hdmi" 2) "samsung,exynos4212-hdmi" 3) "samsung,exynos5420-hdmi" + 4) "samsung,exynos5433-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -12,6 +13,11 @@ Required properties: a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 4210, 4212, 5420 and 5433: - clocks: list of clock IDs from SoC clock driver. a) hdmi: Gate of HDMI IP bus clock. b) sclk_hdmi: Gate of HDMI special clock. @@ -25,9 +31,24 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". -- ddc: phandle to the hdmi ddc node -- phy: phandle to the hdmi phy node -- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 5433: +- clocks: list of clock specifiers according to common clock bindings. + a) hdmi_pclk: Gate of HDMI IP APB bus. + b) hdmi_i_pclk: Gate of HDMI-PHY IP APB bus. + d) i_tmds_clk: Gate of HDMI TMDS clock. + e) i_pixel_clk: Gate of HDMI pixel clock. + f) i_spdif_clk: Gate of HDMI SPDIF clock. + g) oscclk: Oscillator clock, used as parent of following *_user clocks + in case HDMI-PHY is not operational. + h) tmds_clko: TMDS clock generated by HDMI-PHY. + i) tmds_clko_user: MUX used to switch between oscclk and tmds_clko, + respectively if HDMI-PHY is off and operational. + j) pixel_clko: Pixel clock generated by HDMI-PHY. + k) pixel_clko_user: MUX used to switch between oscclk and pixel_clko, + respectively if HDMI-PHY is off and operational. +- clock-names: aliases for above clock specfiers. +- samsung,sysreg: handle to syscon used to control the system registers. Example: diff --git a/Documentation/devicetree/bindings/display/fsl,dcu.txt b/Documentation/devicetree/bindings/display/fsl,dcu.txt index ebf1be9ae..ae55cde1b 100644 --- a/Documentation/devicetree/bindings/display/fsl,dcu.txt +++ b/Documentation/devicetree/bindings/display/fsl,dcu.txt @@ -6,17 +6,24 @@ Required properties: * "fsl,vf610-dcu". - reg: Address and length of the register set for dcu. -- clocks: From common clock binding: handle to dcu clock. -- clock-names: From common clock binding: Shall be "dcu". +- clocks: Handle to "dcu" and "pix" clock (in the order below) + This can be the same clock (e.g. LS1021a) + See ../clocks/clock-bindings.txt for details. +- clock-names: Should be "dcu" and "pix" + See ../clocks/clock-bindings.txt for details. - big-endian Boolean property, LS1021A DCU registers are big-endian. - fsl,panel: The phandle to panel node. +Optional properties: +- fsl,tcon: The phandle to the timing controller node. + Examples: dcu: dcu@2ce0000 { compatible = "fsl,ls1021a-dcu"; reg = <0x0 0x2ce0000 0x0 0x10000>; - clocks = <&platform_clk 0>; - clock-names = "dcu"; + clocks = <&platform_clk 0>, <&platform_clk 0>; + clock-names = "dcu", "pix"; big-endian; fsl,panel = <&panel>; + fsl,tcon = <&tcon>; }; diff --git a/Documentation/devicetree/bindings/display/fsl,tcon.txt b/Documentation/devicetree/bindings/display/fsl,tcon.txt new file mode 100644 index 000000000..6fa4ab668 --- /dev/null +++ b/Documentation/devicetree/bindings/display/fsl,tcon.txt @@ -0,0 +1,18 @@ +Device Tree bindings for Freescale TCON Driver + +Required properties: +- compatible: Should be one of + * "fsl,vf610-tcon". + +- reg: Address and length of the register set for tcon. +- clocks: From common clock binding: handle to tcon ipg clock. +- clock-names: From common clock binding: Shall be "ipg". + +Examples: +timing-controller@4003d000 { + compatible = "fsl,vf610-tcon"; + reg = <0x4003d000 0x1000>; + clocks = <&clks VF610_CLK_TCON0>; + clock-names = "ipg"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt new file mode 100644 index 000000000..d270bfe4e --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt @@ -0,0 +1,72 @@ +Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver + +A DSI Host Controller resides in the middle of display controller and external +HDMI converter or panel. + +Required properties: +- compatible: value should be "hisilicon,hi6220-dsi". +- reg: physical base address and length of dsi controller's registers. +- clocks: contains APB clock phandle + clock-specifier pair. +- clock-names: should be "pclk". +- ports: contains DSI controller input and output sub port. + The input port connects to ADE output port with the reg value "0". + The output port with the reg value "1", it could connect to panel or + any other bridge endpoints. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +A example of HiKey board hi6220 SoC and board specific DT entry: +Example: + +SoC specific: + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; + + +Board specific: + &dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; + }; + + &i2c2 { + ... + + adv7533: adv7533@39 { + ... + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt new file mode 100644 index 000000000..38dc9d60e --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -0,0 +1,64 @@ +Device-Tree bindings for hisilicon ADE display controller driver + +ADE (Advanced Display Engine) is the display controller which grab image +data from memory, do composition, do post image processing, generate RGB +timing stream and transfer to DSI. + +Required properties: +- compatible: value should be "hisilicon,hi6220-ade". +- reg: physical base address and length of the ADE controller's registers. +- hisilicon,noc-syscon: ADE NOC QoS syscon. +- resets: The ADE reset controller node. +- interrupt: the ldi vblank interrupt number used. +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain: + "clk_ade_core" for the ADE core clock. + "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with + jpeg codec. + "clk_ade_pix" for the ADE pixel clok. +- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' + phandle + clock-specifier pairs. +- assigned-clock-rates: clock rates, one for each entry in assigned-clocks. + The rate of "clk_ade_core" could be "360000000" or "180000000"; + The rate of "clk_codec_jpeg" could be or less than "1440000000". + These rate values could be configured according to performance and power + consumption. +- port: the output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected DSI input endpoint. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +Optional properties: +- dma-coherent: Present if dma operations are coherent. + + +A example of HiKey board hi6220 SoC specific DT entry: +Example: + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 0a175d991..a407462c8 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,6 +62,7 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt new file mode 100644 index 000000000..db6e77edb --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -0,0 +1,203 @@ +Mediatek display subsystem +========================== + +The Mediatek display subsystem consists of various DISP function blocks in the +MMSYS register space. The connections between them can be configured by output +and input selectors in the MMSYS_CONFIG register space. Pixel clock and start +of frame signal are distributed to the other function blocks by a DISP_MUTEX +function block. + +All DISP device tree nodes must be siblings to the central MMSYS_CONFIG node. +For a description of the MMSYS_CONFIG binding, see +Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt. + +DISP function blocks +==================== + +A display stream starts at a source function block that reads pixel data from +memory and ends with a sink function block that drives pixels on a display +interface, or writes pixels back to memory. All DISP function blocks have +their own register space, interrupt, and clock gate. The blocks that can +access memory additionally have to list the IOMMU and local arbiter they are +connected to. + +For a description of the display interface sink function blocks, see +Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt and +Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt. + +Required properties (all function blocks): +- compatible: "mediatek,-disp-", one of + "mediatek,-disp-ovl" - overlay (4 layers, blending, csc) + "mediatek,-disp-rdma" - read DMA / line buffer + "mediatek,-disp-wdma" - write DMA + "mediatek,-disp-color" - color processor + "mediatek,-disp-aal" - adaptive ambient light controller + "mediatek,-disp-gamma" - gamma correction + "mediatek,-disp-merge" - merge streams from two RDMA sources + "mediatek,-disp-split" - split stream to two encoders + "mediatek,-disp-ufoe" - data compression engine + "mediatek,-dsi" - DSI controller, see mediatek,dsi.txt + "mediatek,-dpi" - DPI controller, see mediatek,dpi.txt + "mediatek,-disp-mutex" - display mutex + "mediatek,-disp-od" - overdrive +- reg: Physical base address and length of the function block register space +- interrupts: The interrupt signal from the function block (required, except for + merge and split function blocks). +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. + For most function blocks this is just a single clock input. Only the DSI and + DPI controller nodes have multiple clock inputs. These are documented in + mediatek,dsi.txt and mediatek,dpi.txt, respectively. + +Required properties (DMA function blocks): +- compatible: Should be one of + "mediatek,-disp-ovl" + "mediatek,-disp-rdma" + "mediatek,-disp-wdma" +- larb: Should contain a phandle pointing to the local arbiter device as defined + in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt +- iommus: Should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Examples: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + #clock-cells = <1>; +}; + +ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; +}; + +ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; +}; + +rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; +}; + +rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; +}; + +rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; +}; + +wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; +}; + +wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; +}; + +color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; +}; + +color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; +}; + +aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; +}; + +gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; +}; + +ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; +}; + +dsi0: dsi@1401b000 { + /* See mediatek,dsi.txt for details */ +}; + +dpi0: dpi@1401d000 { + /* See mediatek,dpi.txt for details */ +}; + +mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = ; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; +}; + +od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OD>; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt new file mode 100644 index 000000000..b6a7e7397 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -0,0 +1,35 @@ +Mediatek DPI Device +=================== + +The Mediatek DPI function block is a sink of the display subsystem and +provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel +output bus. + +Required properties: +- compatible: "mediatek,-dpi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "engine", and "pll" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached HDMI or LVDS encoder chip. + +Example: + +dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = ; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000..2b1585a34 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,60 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,-dsi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,-mipi-tx" +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = ; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt new file mode 100644 index 000000000..3e10cd782 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt @@ -0,0 +1,7 @@ +Innolux AT070TN92 7.0" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at070tn92" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt new file mode 100644 index 000000000..74540a090 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt @@ -0,0 +1,7 @@ +Olimex 4.3" TFT LCD panel + +Required properties: +- compatible: should be "olimex,lcd-olinuxino-43-ts" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt new file mode 100644 index 000000000..3d8a5e029 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt @@ -0,0 +1,7 @@ +On Tat Industrial Company 7" DPI TFT panel. + +Required properties: +- compatible: should be "ontat,yx700wv03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt new file mode 100644 index 000000000..a2613b967 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 7" integrated projected capacitive touch display with, +800 x 480 (WVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f07a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt new file mode 100644 index 000000000..b9d051196 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 10.1" integrated projected capacitive touch display with, +1024 x 600 (WSVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f10a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt new file mode 100644 index 000000000..e832ff98f --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -0,0 +1,92 @@ +Rockchip RK3288 specific extensions to the Analogix Display Port +================================ + +Required properties: +- compatible: "rockchip,rk3288-edp"; + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. + +- clock-names: from common clock binding: + Required elements: "dp" "pclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. +- pinctrl-0: pin-control mode. should be <&edp_hpd> + +- reset-names: Must include the name "dp" + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: there are 2 port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0: contained 2 endpoints, connecting to the output of vop. + Port 1: contained 1 endpoint, connecting to the input of panel. + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt +- phys (required) +- phy-names (required) +- hpd-gpios (optional) +- force-hpd (optional) +------------------------------------------------------------------------------- + +Example: + dp-controller: dp@ff970000 { + compatible = "rockchip,rk3288-dp"; + reg = <0xff970000 0x4000>; + interrupts = ; + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; + clock-names = "dp", "pclk"; + phys = <&dp_phy>; + phy-names = "dp"; + + rockchip,grf = <&grf>; + resets = <&cru 111>; + reset-names = "dp"; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + edp_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + edp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_edp>; + }; + edp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_edp>; + }; + }; + + edp_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + edp_out_panel: endpoint { + reg = <0>; + remote-endpoint = <&panel_in_edp> + }; + }; + }; + }; + + pinctrl { + edp { + edp_hpd: edp-hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/snps,arcpgu.txt b/Documentation/devicetree/bindings/display/snps,arcpgu.txt new file mode 100644 index 000000000..c5c7dfd37 --- /dev/null +++ b/Documentation/devicetree/bindings/display/snps,arcpgu.txt @@ -0,0 +1,35 @@ +ARC PGU + +This is a display controller found on several development boards produced +by Synopsys. The ARC PGU is an RGB streamer that reads the data from a +framebuffer and sends it to a single digital encoder (usually HDMI). + +Required properties: + - compatible: "snps,arcpgu" + - reg: Physical base address and length of the controller's registers. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For ARC PGU it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The PGU connection to an encoder chip. + +Example: + +/ { + ... + + pgu@XXXXXXXX { + compatible = "snps,arcpgu"; + reg = <0xXXXXXXXX 0x400>; + clocks = <&clock_node>; + clock-names = "pxlclk"; + + port { + pgu_output: endpoint { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt new file mode 100644 index 000000000..df8f4aeef --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -0,0 +1,258 @@ +Allwinner A10 Display Pipeline +============================== + +The Allwinner A10 Display pipeline is composed of several components +that are going to be documented below: + +TV Encoder +---------- + +The TV Encoder supports the composite and VGA output. It is one end of +the pipeline. + +Required properties: + - compatible: value should be "allwinner,sun4i-a10-tv-encoder". + - reg: base address and size of memory-mapped region + - clocks: the clocks driving the TV encoder + - resets: phandle to the reset controller driving the encoder + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. + +TCON +---- + +The TCON acts as a timing controller for RGB, LVDS and TV interfaces. + +Required properties: + - compatible: value should be "allwinner,sun5i-a13-tcon". + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the TCON. Three are needed: + - 'ahb': the interface clocks + - 'tcon-ch0': The clock driving the TCON channel 0 + - 'tcon-ch1': The clock driving the TCON channel 1 + - resets: phandles to the reset controllers driving the encoder + - "lcd": the reset line for the TCON channel 0 + + - clock-names: the clock names mentioned above + - reset-names: the reset names mentioned above + - clock-output-names: Name of the pixel clock created + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, the second one the output + + The output should have two endpoints. The first is the block + connected to the TCON channel 0 (usually a panel or a bridge), the + second the block connected to the TCON channel 1 (usually the TV + encoder) + + +Display Engine Backend +---------------------- + +The display engine backend exposes layers and sprites to the +system. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-backend + - reg: base address and size of the memory-mapped region. + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the output + +Display Engine Frontend +----------------------- + +The display engine frontend does formats conversion, scaling, +deinterlacing and color space conversion. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-frontend + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs + + +Display Engine Pipeline +----------------------- + +The display engine pipeline (and its entry point, since it can be +either directly the backend or the frontend) is represented as an +extra node. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-engine + + - allwinner,pipelines: list of phandle to the display engine + frontends available. + +Example: + +panel: panel { + compatible = "olimex,lcd-olinuxino-43-ts"; + #address-cells = <1>; + #size-cells = <0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; +}; + +tve0: tv-encoder@01c0a000 { + compatible = "allwinner,sun4i-a10-tv-encoder"; + reg = <0x01c0a000 0x1000>; + clocks = <&ahb_gates 34>; + resets = <&tcon_ch0_clk 0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + tve0_in_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_tve0>; + }; + }; +}; + +tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun5i-a13-tcon"; + reg = <0x01c0c000 0x1000>; + interrupts = <44>; + resets = <&tcon_ch0_clk 1>; + reset-names = "lcd"; + clocks = <&ahb_gates 36>, + <&tcon_ch0_clk>, + <&tcon_ch1_clk>; + clock-names = "ahb", + "tcon-ch0", + "tcon-ch1"; + clock-output-names = "tcon-pixel-clock"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon0_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + + tcon0_out_tve0: endpoint@1 { + reg = <1>; + remote-endpoint = <&tve0_in_tcon0>; + }; + }; + }; +}; + +fe0: display-frontend@1e00000 { + compatible = "allwinner,sun5i-a13-display-frontend"; + reg = <0x01e00000 0x20000>; + interrupts = <47>; + clocks = <&ahb_gates 46>, <&de_fe_clk>, + <&dram_gates 25>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_fe_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe0_out_be0: endpoint { + remote-endpoint = <&be0_in_fe0>; + }; + }; + }; +}; + +be0: display-backend@1e60000 { + compatible = "allwinner,sun5i-a13-display-backend"; + reg = <0x01e60000 0x10000>; + clocks = <&ahb_gates 44>, <&de_be_clk>, + <&dram_gates 26>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_be_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be0_in_fe0: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe0_out_be0>; + }; + }; + + be0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_be0>; + }; + }; + }; +}; + +display-engine { + compatible = "allwinner,sun5i-a13-display-engine"; + allwinner,pipelines = <&fe0>; +}; diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt index 1396078d1..baf9b34d2 100644 --- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt +++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt @@ -12,6 +12,10 @@ Required properties: - reg: Should contain DMA registers location and length. - interrupts: Should contain the DMA interrupts associated to the DMA channels in ascending order. +- interrupt-names: Should contain the names of the interrupt + in the form "dmaXX". + Use "dma-shared-all" for the common interrupt line + that is shared by all dma channels. - #dma-cells: Must be <1>, the cell in the dmas property of the client device represents the DREQ number. - brcm,dma-channel-mask: Bit mask representing the channels @@ -34,13 +38,35 @@ dma: dma@7e007000 { <1 24>, <1 25>, <1 26>, + /* dma channel 11-14 share one irq */ <1 27>, + <1 27>, + <1 27>, + <1 27>, + /* unused shared irq for all channels */ <1 28>; + interrupt-names = "dma0", + "dma1", + "dma2", + "dma3", + "dma4", + "dma5", + "dma6", + "dma7", + "dma8", + "dma9", + "dma10", + "dma11", + "dma12", + "dma13", + "dma14", + "dma-shared-all"; #dma-cells = <1>; brcm,dma-channel-mask = <0x7f35>; }; + DMA clients connected to the BCM2835 DMA controller must use the format described in the dma.txt file, using a two-cell specifier for each channel. diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index c6e72501a..c680fbd4d 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -58,6 +58,15 @@ The third cell specifies the transfer priority as below. 1 Medium 2 Low +Optional properties: + +- gpr : The phandle to the General Purpose Register (GPR) node. +- fsl,sdma-event-remap : Register bits of sdma event remap, the format is + . + reg is the GPR register offset. + shift is the bit position inside the GPR register. + val is the value of the bit (0 or 1). + Examples: sdma@83fb0000 { @@ -83,3 +92,21 @@ ssi2: ssi@70014000 { dma-names = "rx", "tx"; fsl,fifo-depth = <15>; }; + +Using the fsl,sdma-event-remap property: + +If we want to use SDMA on the SAI1 port on a MX6SX: + +&sdma { + gpr = <&gpr>; + /* SDMA events remap for SAI1_RX and SAI1_TX */ + fsl,sdma-event-remap = <0 15 1>, <0 16 1>; +}; + +The fsl,sdma-event-remap property in this case has two values: +- <0 15 1> means that the offset is 0, so GPR0 is the register of the +SDMA remap. Bit 15 of GPR0 selects between UART4_RX and SAI1_RX. +Setting bit 15 to 1 selects SAI1_RX. +- <0 16 1> means that the offset is 0, so GPR0 is the register of the +SDMA remap. Bit 16 of GPR0 selects between UART4_TX and SAI1_TX. +Setting bit 16 to 1 selects SAI1_TX. diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt index 276ef815e..c075f5988 100644 --- a/Documentation/devicetree/bindings/dma/mv-xor.txt +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -1,7 +1,10 @@ * Marvell XOR engines Required properties: -- compatible: Should be "marvell,orion-xor" or "marvell,armada-380-xor" +- compatible: Should be one of the following: + - "marvell,orion-xor" + - "marvell,armada-380-xor" + - "marvell,armada-3700-xor". - reg: Should contain registers location and length (two sets) the first set is the low registers, the second set the high registers for the XOR engine. diff --git a/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt new file mode 100644 index 000000000..c6908e7c4 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt @@ -0,0 +1,44 @@ +* NVIDIA Tegra APB DMA controller + +Required properties: +- compatible: Should be "nvidia,-apbdma" +- reg: Should contain DMA registers location and length. This shuld include + all of the per-channel registers. +- interrupts: Should contain all of the per-channel DMA interrupts. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - dma +- #dma-cells : Must be <1>. This dictates the length of DMA specifiers in + client nodes' dmas properties. The specifier represents the DMA request + select value for the peripheral. For more details, consult the Tegra TRM's + documentation of the APB DMA channel control register REQ_SEL field. + +Examples: + +apbdma: dma@6000a000 { + compatible = "nvidia,tegra20-apbdma"; + reg = <0x6000a000 0x1200>; + interrupts = < 0 136 0x04 + 0 137 0x04 + 0 138 0x04 + 0 139 0x04 + 0 140 0x04 + 0 141 0x04 + 0 142 0x04 + 0 143 0x04 + 0 144 0x04 + 0 145 0x04 + 0 146 0x04 + 0 147 0x04 + 0 148 0x04 + 0 149 0x04 + 0 150 0x04 + 0 151 0x04 >; + clocks = <&tegra_car 34>; + resets = <&tegra_car 34>; + reset-names = "dma"; + #dma-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt new file mode 100644 index 000000000..1e1dc8f97 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt @@ -0,0 +1,55 @@ +* NVIDIA Tegra Audio DMA (ADMA) controller + +The Tegra Audio DMA controller that is used for transferring data +between system memory and the Audio Processing Engine (APE). + +Required properties: +- compatible: Must be "nvidia,tegra210-adma". +- reg: Should contain DMA registers location and length. This should be + a single entry that includes all of the per-channel registers in one + contiguous bank. +- interrupt-parent: Phandle to the interrupt parent controller. +- interrupts: Should contain all of the per-channel DMA interrupts in + ascending order with respect to the DMA channel index. +- clocks: Must contain one entry for the ADMA module clock + (TEGRA210_CLK_D_AUDIO). +- clock-names: Must contain the name "d_audio" for the corresponding + 'clocks' entry. +- #dma-cells : Must be 1. The first cell denotes the receive/transmit + request number and should be between 1 and the maximum number of + requests supported. This value corresponds to the RX/TX_REQUEST_SELECT + fields in the ADMA_CHn_CTRL register. + + +Example: + +adma: dma@702e2000 { + compatible = "nvidia,tegra210-adma"; + reg = <0x0 0x702e2000 0x0 0x2000>; + interrupt-parent = <&tegra_agic>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + clocks = <&tegra_car TEGRA210_CLK_D_AUDIO>; + clock-names = "d_audio"; + #dma-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index 1c9d48ea4..9cbf5d9df 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -13,6 +13,8 @@ Required properties: - clock-names: must contain "bam_clk" entry - qcom,ee : indicates the active Execution Environment identifier (0-7) used in the secure world. +- qcom,controlled-remotely : optional, indicates that the bam is controlled by + remote proccessor i.e. execution environment. Example: diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index c26159816..0f5583293 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -13,6 +13,11 @@ Required properties: - chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1: increase from chan n->0 - block_size: Maximum block size supported by the controller +- data-width: Maximum data width supported by hardware per AHB master + (in bytes, power of 2) + + +Deprecated properties: - data_width: Maximum data width supported by hardware per AHB master (0 - 8bits, 1 - 16bits, ..., 5 - 256bits) @@ -38,7 +43,7 @@ Example: chan_allocation_order = <1>; chan_priority = <1>; block_size = <0xfff>; - data_width = <3 3>; + data-width = <8 8>; }; DMA clients connected to the Designware DMA controller must use the format @@ -47,8 +52,8 @@ The four cells in order are: 1. A phandle pointing to the DMA controller 2. The DMA request line number -3. Source master for transfers on allocated channel -4. Destination master for transfers on allocated channel +3. Memory master for transfers on allocated channel +4. Peripheral master for transfers on allocated channel Example: diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt deleted file mode 100644 index c6908e7c4..000000000 --- a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt +++ /dev/null @@ -1,44 +0,0 @@ -* NVIDIA Tegra APB DMA controller - -Required properties: -- compatible: Should be "nvidia,-apbdma" -- reg: Should contain DMA registers location and length. This shuld include - all of the per-channel registers. -- interrupts: Should contain all of the per-channel DMA interrupts. -- clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include the following entries: - - dma -- #dma-cells : Must be <1>. This dictates the length of DMA specifiers in - client nodes' dmas properties. The specifier represents the DMA request - select value for the peripheral. For more details, consult the Tegra TRM's - documentation of the APB DMA channel control register REQ_SEL field. - -Examples: - -apbdma: dma@6000a000 { - compatible = "nvidia,tegra20-apbdma"; - reg = <0x6000a000 0x1200>; - interrupts = < 0 136 0x04 - 0 137 0x04 - 0 138 0x04 - 0 139 0x04 - 0 140 0x04 - 0 141 0x04 - 0 142 0x04 - 0 143 0x04 - 0 144 0x04 - 0 145 0x04 - 0 146 0x04 - 0 147 0x04 - 0 148 0x04 - 0 149 0x04 - 0 150 0x04 - 0 151 0x04 >; - clocks = <&tegra_car 34>; - resets = <&tegra_car 34>; - reset-names = "dma"; - #dma-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt index 2291c4098..3cf0072d3 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -7,7 +7,7 @@ Required properties: - compatible: Should be "xlnx,axi-dma-1.00.a" - #dma-cells: Should be <1>, see "dmas" property below - reg: Should contain DMA registers location and length. -- dma-channel child node: Should have atleast one channel and can have upto +- dma-channel child node: Should have at least one channel and can have up to two channels per device. This node specifies the properties of each DMA channel (see child node properties below). diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt index e4c4d47f8..a1f2683c4 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt @@ -3,18 +3,44 @@ It can be configured to have one channel or two channels. If configured as two channels, one is to transmit to the video device and another is to receive from the video device. +Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream +target devices. It can be configured to have one channel or two channels. +If configured as two channels, one is to transmit to the device and another +is to receive from the device. + +Xilinx AXI CDMA engine, it does transfers between memory-mapped source +address and a memory-mapped destination address. + Required properties: -- compatible: Should be "xlnx,axi-vdma-1.00.a" +- compatible: Should be "xlnx,axi-vdma-1.00.a" or "xlnx,axi-dma-1.00.a" or + "xlnx,axi-cdma-1.00.a"" - #dma-cells: Should be <1>, see "dmas" property below - reg: Should contain VDMA registers location and length. -- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. +- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits). +- dma-ranges: Should be as the following . - dma-channel child node: Should have at least one channel and can have up to two channels per device. This node specifies the properties of each DMA channel (see child node properties below). +- clocks: Input clock specifier. Refer to common clock bindings. +- clock-names: List of input clocks + For VDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk" "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk" + For CDMA: + Required elements: "s_axi_lite_aclk", "m_axi_aclk" + FOR AXIDMA: + Required elements: "s_axi_lite_aclk" + Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axi_sg_aclk" + +Required properties for VDMA: +- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. Optional properties: - xlnx,include-sg: Tells configured for Scatter-mode in the hardware. +Optional properties for VDMA: - xlnx,flush-fsync: Tells which channel to Flush on Frame sync. It takes following values: {1}, flush both channels @@ -31,6 +57,7 @@ Required child node properties: Optional child node properties: - xlnx,include-dre: Tells hardware is configured for Data Realignment Engine. +Optional child node properties for VDMA: - xlnx,genlock-mode: Tells Genlock synchronization is enabled/disabled in hardware. @@ -41,8 +68,13 @@ axi_vdma_0: axivdma@40030000 { compatible = "xlnx,axi-vdma-1.00.a"; #dma_cells = <1>; reg = < 0x40030000 0x10000 >; + dma-ranges = <0x00000000 0x00000000 0x40000000>; xlnx,num-fstores = <0x8>; xlnx,flush-fsync = <0x1>; + xlnx,addrwidth = <0x20>; + clocks = <&clk 0>, <&clk 1>, <&clk 2>, <&clk 3>, <&clk 4>; + clock-names = "s_axi_lite_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk", + "m_axis_mm2s_aclk", "s_axis_s2mm_aclk"; dma-channel@40030000 { compatible = "xlnx,axi-vdma-mm2s-channel"; interrupts = < 0 54 4 >; diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt index cc2608021..ce1b2231b 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -1,7 +1,9 @@ * Generic 8-bits shift register GPIO driver Required properties: -- compatible : Should be "fairchild,74hc595" +- compatible: Should contain one of the following: + "fairchild,74hc595" + "nxp,74lvc594" - reg : chip select number - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 120bc4971..4b6cc632c 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -1,9 +1,10 @@ -* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller +* Freescale MPC512x/MPC8xxx/QorIQ/Layerscape GPIO controller Required properties: - compatible : Should be "fsl,-gpio" The following s are known to be supported: - mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq, + ls1021a, ls1043a, ls2080a. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and @@ -15,7 +16,7 @@ Optional properties: - little-endian : GPIO registers are used as little endian. If not present registers are used as big endian by default. -Example: +Example of gpio-controller node for a mpc5125 SoC: gpio0: gpio@1100 { compatible = "fsl,mpc5125-gpio"; @@ -24,3 +25,16 @@ gpio0: gpio@1100 { interrupts = <78 0x8>; status = "okay"; }; + +Example of gpio-controller node for a ls2080a SoC: + +gpio0: gpio@2300000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt deleted file mode 100644 index d4eab9227..000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt +++ /dev/null @@ -1,36 +0,0 @@ -Driver a GPIO line that can be used to turn the power off. - -The driver supports both level triggered and edge triggered power off. -At driver load time, the driver will request the given gpio line and -install a pm_power_off handler. If the optional properties 'input' is -not found, the GPIO line will be driven in the inactive -state. Otherwise its configured as an input. - -When the pm_power_off is called, the gpio is configured as an output, -and drive active, so triggering a level triggered power off -condition. This will also cause an inactive->active edge condition, so -triggering positive edge triggered power off. After a delay of 100ms, -the GPIO is set to inactive, thus causing an active->inactive edge, -triggering negative edge triggered power off. After another 100ms -delay the GPIO is driver active again. If the power is still on and -the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. - -Required properties: -- compatible : should be "gpio-poweroff". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to power down the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- input : Initially configure the GPIO line as an input. Only reconfigure - it to an output when the pm_power_off function is called. If this optional - property is not specified, the GPIO is initialized as an output in its - inactive state. - -Examples: - -gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; -}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/gpio/gpio-restart.txt deleted file mode 100644 index af3701bc1..000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-restart.txt +++ /dev/null @@ -1,54 +0,0 @@ -Drive a GPIO line that can be used to restart the system from a restart -handler. - -This binding supports level and edge triggered reset. At driver load -time, the driver will request the given gpio line and install a restart -handler. If the optional properties 'open-source' is not found, the GPIO line -will be driven in the inactive state. Otherwise its not driven until -the restart is initiated. - -When the system is restarted, the restart handler will be invoked in -priority order. The gpio is configured as an output, and driven active, -triggering a level triggered reset condition. This will also cause an -inactive->active edge condition, triggering positive edge triggered -reset. After a delay specified by active-delay, the GPIO is set to -inactive, thus causing an active->inactive edge, triggering negative edge -triggered reset. After a delay specified by inactive-delay, the GPIO -is driven active again. After a delay specified by wait-delay, the -restart handler completes allowing other restart handlers to be attempted. - -Required properties: -- compatible : should be "gpio-restart". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to reset the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- open-source : Treat the GPIO as being open source and defer driving - it to when the restart is initiated. If this optional property is not - specified, the GPIO is initialized as an output in its inactive state. -- priority : A priority ranging from 0 to 255 (default 128) according to - the following guidelines: - 0: Restart handler of last resort, with limited restart - capabilities - 128: Default restart handler; use if no other restart handler is - expected to be available, and/or if restart functionality is - sufficient to restart the entire system - 255: Highest priority restart handler, will preempt all other - restart handlers -- active-delay: Delay (default 100) to wait after driving gpio active [ms] -- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] -- wait-delay: Delay (default 3000) to wait after completing restart - sequence [ms] - -Examples: - -gpio-restart { - compatible = "gpio-restart"; - gpios = <&gpio 4 0>; - priority = <128>; - active-delay = <100>; - inactive-delay = <100>; - wait-delay = <3000>; -}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt index 262ee4ddf..28662d83a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt @@ -3,6 +3,8 @@ Netlogic XLP Family GPIO This GPIO driver is used for following Netlogic XLP SoCs: XLP832, XLP316, XLP208, XLP980, XLP532 +This GPIO driver is also compatible with GPIO controller found on +Broadcom Vulcan ARM64. Required properties: ------------------- @@ -13,6 +15,7 @@ Required properties: - "netlogic,xlp208-gpio": For Netlogic XLP208 - "netlogic,xlp980-gpio": For Netlogic XLP980 - "netlogic,xlp532-gpio": For Netlogic XLP532 + - "brcm,vulcan-gpio": For Broadcom Vulcan ARM64 - reg: Physical base address and length of the controller's registers. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 069cdf6f9..68d28f62a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -131,6 +131,13 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Some system-on-chips (SoCs) use the concept of GPIO banks. A GPIO bank is an +instance of a hardware IP core on a silicon die, usually exposed to the +programmer as a coherent range of I/O addresses. Usually each such bank is +exposed in the device tree as an individual gpio-controller node, reflecting +the fact that the hardware was synthesized by reusing the same IP block a +few times over. + Optionally, a GPIO controller may have a "ngpios" property. This property indicates the number of in-use slots of available slots for GPIOs. The typical example is something like this: the hardware register is 32 bits @@ -145,6 +152,21 @@ additional bitmask is needed to specify which GPIOs are actually in use, and which are dummies. The bindings for this case has not yet been specified, but should be specified if/when such hardware appears. +Optionally, a GPIO controller may have a "gpio-line-names" property. This is +an array of strings defining the names of the GPIO lines going out of the +GPIO controller. This name should be the most meaningful producer name +for the system, such as a rail name indicating the usage. Package names +such as pin name are discouraged: such lines have opaque names (since they +are by definition generic purpose) and such names are usually not very +helpful. For example "MMC-CD", "Red LED Vdd" and "ethernet reset" are +reasonable line names as they describe what the line is used for. "GPIO0" +is not a good name to give to a GPIO line. Placeholders are discouraged: +rather use the "" (blank string) if the use of the GPIO line is undefined +in your design. The names are assigned starting from line offset 0 from +left to right from the passed array. An incomplete array (where the number +of passed named are less than ngpios) will still be used up until the last +provided valid line index. + Example: gpio-controller@00000000 { @@ -153,6 +175,10 @@ gpio-controller@00000000 { gpio-controller; #gpio-cells = <2>; ngpios = <18>; + gpio-line-names = "MMC-CD", "MMC-WP", "VDD eth", "RST eth", "LED R", + "LED G", "LED B", "Col A", "Col B", "Col C", "Col D", + "Row A", "Row B", "Row C", "Row D", "NMI button", + "poweroff", "reset"; } The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism diff --git a/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt new file mode 100644 index 000000000..d58b3958f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt @@ -0,0 +1,24 @@ +* IBM/AMCC/APM GPIO Controller for PowerPC 4XX series and compatible SoCs + +All GPIOs are pin-shared with other functions. DCRs control whether a +particular pin that has GPIO capabilities acts as a GPIO or is used for +another purpose. GPIO outputs are separately programmable to emulate +an open-drain driver. + +Required properties: + - compatible: must be "ibm,ppc4xx-gpio" + - reg: address and length of the register set for the device + - #gpio-cells: must be set to 2. The first cell is the pin number + and the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: marks the device node as a gpio controller. + +Example: + +GPIO0: gpio@ef600b00 { + compatible = "ibm,ppc4xx-gpio"; + reg = <0xef600b00 0x00000048>; + #gpio-cells = <2>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt index ef3752889..dd031fc93 100644 --- a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -33,7 +33,7 @@ gpio0: gpio0@1f860000 { gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&PBCLK4>; + clocks = <&rootclk PB4CLK>; microchip,gpio-bank = <0>; gpio-ranges = <&pic32_pinctrl 0 0 16>; }; diff --git a/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt new file mode 100644 index 000000000..c82a2e221 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt @@ -0,0 +1,161 @@ +NVIDIA Tegra186 GPIO controllers + +Tegra186 contains two GPIO controllers; a main controller and an "AON" +controller. This binding document applies to both controllers. The register +layouts for the controllers share many similarities, but also some significant +differences. Hence, this document describes closely related but different +bindings and compatible values. + +The Tegra186 GPIO controller allows software to set the IO direction of, and +read/write the value of, numerous GPIO signals. Routing of GPIO signals to +package balls is under the control of a separate pin controller HW block. Two +major sets of registers exist: + +a) Security registers, which allow configuration of allowed access to the GPIO +register set. These registers exist in a single contiguous block of physical +address space. The size of this block, and the security features available, +varies between the different GPIO controllers. + +Access to this set of registers is not necessary in all circumstances. Code +that wishes to configure access to the GPIO registers needs access to these +registers to do so. Code which simply wishes to read or write GPIO data does not +need access to these registers. + +b) GPIO registers, which allow manipulation of the GPIO signals. In some GPIO +controllers, these registers are exposed via multiple "physical aliases" in +address space, each of which access the same underlying state. See the hardware +documentation for rationale. Any particular GPIO client is expected to access +just one of these physical aliases. + +Tegra HW documentation describes a unified naming convention for all GPIOs +implemented by the SoC. Each GPIO is assigned to a port, and a port may control +a number of GPIOs. Thus, each GPIO is named according to an alphabetical port +name and an integer GPIO name within the port. For example, GPIO_PA0, GPIO_PN6, +or GPIO_PCC3. + +The number of ports implemented by each GPIO controller varies. The number of +implemented GPIOs within each port varies. GPIO registers within a controller +are grouped and laid out according to the port they affect. + +The mapping from port name to the GPIO controller that implements that port, and +the mapping from port name to register offset within a controller, are both +extremely non-linear. The header file +describes the port-level mapping. In that file, the naming convention for ports +matches the HW documentation. The values chosen for the names are alphabetically +sorted within a particular controller. Drivers need to map between the DT GPIO +IDs and HW register offsets using a lookup table. + +Each GPIO controller can generate a number of interrupt signals. Each signal +represents the aggregate status for all GPIOs within a set of ports. Thus, the +number of interrupt signals generated by a controller varies as a rough function +of the number of ports it implements. Note that the HW documentation refers to +both the overall controller HW module and the sets-of-ports as "controllers". + +Each GPIO controller in fact generates multiple interrupts signals for each set +of ports. Each GPIO may be configured to feed into a specific one of the +interrupt signals generated by a set-of-ports. The intent is for each generated +signal to be routed to a different CPU, thus allowing different CPUs to each +handle subsets of the interrupts within a port. The status of each of these +per-port-set signals is reported via a separate register. Thus, a driver needs +to know which status register to observe. This binding currently defines no +configuration mechanism for this. By default, drivers should use register +GPIO_${port}_INTERRUPT_STATUS_G1_0. Future revisions to the binding could +define a property to configure this. + +Required properties: +- compatible + Array of strings. + One of: + - "nvidia,tegra186-gpio". + - "nvidia,tegra186-gpio-aon". +- reg-names + Array of strings. + Contains a list of names for the register spaces described by the reg + property. May contain the following entries, in any order: + - "gpio": Mandatory. GPIO control registers. This may cover either: + a) The single physical alias that this OS should use. + b) All physical aliases that exist in the controller. This is + appropriate when the OS is responsible for managing assignment of + the physical aliases. + - "security": Optional. Security configuration registers. + Users of this binding MUST look up entries in the reg property by name, + using this reg-names property to do so. +- reg + Array of (physical base address, length) tuples. + Must contain one entry per entry in the reg-names property, in a matching + order. +- interrupts + Array of interrupt specifiers. + The interrupt outputs from the HW block, one per set of ports, in the + order the HW manual describes them. The number of entries required varies + depending on compatible value: + - "nvidia,tegra186-gpio": 6 entries. + - "nvidia,tegra186-gpio-aon": 1 entry. +- gpio-controller + Boolean. + Marks the device node as a GPIO controller/provider. +- #gpio-cells + Single-cell integer. + Must be <2>. + Indicates how many cells are used in a consumer's GPIO specifier. + In the specifier: + - The first cell is the pin number. + See . + - The second cell contains flags: + - Bit 0 specifies polarity + - 0: Active-high (normal). + - 1: Active-low (inverted). +- interrupt-controller + Boolean. + Marks the device node as an interrupt controller/provider. +- #interrupt-cells + Single-cell integer. + Must be <2>. + Indicates how many cells are used in a consumer's interrupt specifier. + In the specifier: + - The first cell is the GPIO number. + See . + - The second cell is contains flags: + - Bits [3:0] indicate trigger type and level: + - 1: Low-to-high edge triggered. + - 2: High-to-low edge triggered. + - 4: Active high level-sensitive. + - 8: Active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. + +Example: + +#include + +gpio@2200000 { + compatible = "nvidia,tegra186-gpio"; + reg-names = "security", "gpio"; + reg = + <0x0 0x2200000 0x0 0x10000>, + <0x0 0x2210000 0x0 0x10000>; + interrupts = + <0 47 IRQ_TYPE_LEVEL_HIGH>, + <0 50 IRQ_TYPE_LEVEL_HIGH>, + <0 53 IRQ_TYPE_LEVEL_HIGH>, + <0 56 IRQ_TYPE_LEVEL_HIGH>, + <0 59 IRQ_TYPE_LEVEL_HIGH>, + <0 180 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +gpio@c2f0000 { + compatible = "nvidia,tegra186-gpio-aon"; + reg-names = "security", "gpio"; + reg = + <0x0 0xc2f0000 0x0 0x1000>, + <0x0 0xc2f1000 0x0 0x1000>; + interrupts = + <0 60 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt new file mode 100644 index 000000000..038c3a6a1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt @@ -0,0 +1,38 @@ +Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers. + +The Western Digital MyBook Live has two memory-mapped GPIO controllers. +Both GPIO controller only have a single 8-bit data register, where GPIO +state can be read and/or written. + +Required properties: + - compatible: should be "wd,mbl-gpio" + - reg-names: must contain + "dat" - data register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - no-output: GPIOs are read-only. + +Examples: + gpio0: gpio0@e0000000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0000000 0x1>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio1: gpio1@e0100000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0100000 0x1>; + #gpio-cells = <2>; + gpio-controller; + no-output; + }; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt index 23bfe8e1f..ff3db65e5 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt @@ -1,9 +1,10 @@ -NVIDIA GK20A Graphics Processing Unit +NVIDIA Tegra Graphics Processing Units Required properties: -- compatible: "nvidia,-" +- compatible: "nvidia," Currently recognized values: - - nvidia,tegra124-gk20a + - nvidia,gk20a + - nvidia,gm20b - reg: Physical base address and length of the controller's registers. Must contain two entries: - first entry for bar0 @@ -19,14 +20,20 @@ Required properties: - clock-names: Must include the following entries: - gpu - pwr +If the compatible string is "nvidia,gm20b", then the following clock +is also required: + - ref - resets: Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. - reset-names: Must include the following entries: - gpu -Example: +Optional properties: +- iommus: A reference to the IOMMU. See ../iommu/iommu.txt for details. - gpu@0,57000000 { +Example for GK20A: + + gpu@57000000 { compatible = "nvidia,gk20a"; reg = <0x0 0x57000000 0x0 0x01000000>, <0x0 0x58000000 0x0 0x01000000>; @@ -39,5 +46,25 @@ Example: clock-names = "gpu", "pwr"; resets = <&tegra_car 184>; reset-names = "gpu"; + iommus = <&mc TEGRA_SWGROUP_GPU>; + status = "disabled"; + }; + +Example for GM20B: + + gpu@57000000 { + compatible = "nvidia,gm20b"; + reg = <0x0 0x57000000 0x0 0x01000000>, + <0x0 0x58000000 0x0 0x01000000>; + interrupts = , + ; + interrupt-names = "stall", "nonstall"; + clocks = <&tegra_car TEGRA210_CLK_GPU>, + <&tegra_car TEGRA210_CLK_PLL_P_OUT5>, + <&tegra_car TEGRA210_CLK_PLL_G_REF>; + clock-names = "gpu", "pwr", "ref"; + resets = <&tegra_car 184>; + reset-names = "gpu"; + iommus = <&mc TEGRA_SWGROUP_GPU>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/hwmon/ina2xx.txt b/Documentation/devicetree/bindings/hwmon/ina2xx.txt index 9bcd5e878..02af0d94e 100644 --- a/Documentation/devicetree/bindings/hwmon/ina2xx.txt +++ b/Documentation/devicetree/bindings/hwmon/ina2xx.txt @@ -7,6 +7,7 @@ Required properties: - "ti,ina220" for ina220 - "ti,ina226" for ina226 - "ti,ina230" for ina230 + - "ti,ina231" for ina231 - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt index a7afbf60b..bf2a47bbd 100644 --- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -13,6 +13,7 @@ Required properties: * "lltc,ltc3886" * "lltc,ltc3887" * "lltc,ltm2987" + * "lltc,ltm4675" * "lltc,ltm4676" - reg: I2C slave address diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index bfeabb843..71191ff0e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -44,8 +44,8 @@ Required properties: - our-claim-gpio: The GPIO that we use to claim the bus. - their-claim-gpios: The GPIOs that the other sides use to claim the bus. Note that some implementations may only support a single other master. -- Standard I2C mux properties. See mux.txt in this directory. -- Single I2C child bus node at reg 0. See mux.txt in this directory. +- Standard I2C mux properties. See i2c-mux.txt in this directory. +- Single I2C child bus node at reg 0. See i2c-mux.txt in this directory. Optional properties: - slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us. diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt index 6078aefe7..7ce23ac61 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -27,7 +27,8 @@ Required properties: - i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C parents. -Furthermore, I2C mux properties and child nodes. See mux.txt in this directory. +Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this +directory. Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt index 66709a825..21da3ecbb 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -22,8 +22,8 @@ Required properties: - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. - mux-gpios: list of gpios used to control the muxer -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - idle-state: value to set the muxer to when idle. When no value is @@ -33,7 +33,7 @@ For each i2c child node, an I2C child bus will be created. They will be numbered based on their order in the device tree. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output using the list of +in the relevant node's reg property will be output using the list of GPIOs, the first in the list holding the least-significant value. If an idle state is defined, using the idle-state (optional) property, diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt index ae8af1694..33119a98e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -28,9 +28,9 @@ Also required are: * Standard pinctrl properties that specify the pin mux state for each child bus. See ../pinctrl/pinctrl-bindings.txt. -* Standard I2C mux properties. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. For each named state defined in the pinctrl-names property, an I2C child bus will be created. I2C child bus numbers are assigned based on the index into diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt index 688783fbe..de00d7fc4 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt @@ -7,8 +7,8 @@ Required properties: - compatible: i2c-mux-reg - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - reg: this pair of specifies the register to control the mux. @@ -24,7 +24,7 @@ Optional properties: given, it defaults to the last value used. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output to the register. +in the relevant node's reg property will be output to the register. If an idle state is defined, using the idle-state (optional) property, whenever an access is not being made to a device on a child bus, the diff --git a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt index dced82ebe..872d485df 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt @@ -4,6 +4,12 @@ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + or + + compatible: "cavium,octeon-7890-twsi" + + Compatibility with cn78XX SOCs. + - reg: The base address of the TWSI/I2C bus controller register bank. - #address-cells: Must be <1>. diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index cf8bfc956..5f0cb502b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -19,6 +19,9 @@ Optional properties: - clock-frequency: desired I2C bus clock frequency in Hz. The absence of this property indicates the default frequency 100 kHz. - clocks: clock specifier. +- dmas: Must contain a list of two references to DMA specifiers, one for + transmission, and one for reception. +- dma-names: Must contain a list of two DMA names, "tx" and "rx". - i2c-scl-falling-time-ns: see i2c.txt - i2c-scl-internal-delay-ns: see i2c.txt diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 165937e1a..45f5c5c59 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -1,4 +1,4 @@ -Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC +Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC, MMA8653FC or FXLS8471Q triaxial accelerometer Required properties: @@ -9,6 +9,7 @@ Required properties: * "fsl,mma8453" * "fsl,mma8652" * "fsl,mma8653" + * "fsl,fxls8471" - reg: the I2C address of the chip diff --git a/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt new file mode 100644 index 000000000..0bcae5140 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt @@ -0,0 +1,21 @@ +NXP LPC1850 ADC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-adc" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: + +adc0: adc@400e3000 { + compatible = "nxp,lpc1850-adc"; + reg = <0x400e3000 0x1000>; + interrupts = <17>; + clocks = <&ccu1 CLK_APB3_ADC0>; + vref-supply = <®_vdda>; + resets = <&rgu 40>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt new file mode 100644 index 000000000..555fb117d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt @@ -0,0 +1,47 @@ +* Freescale MXS LRADC device driver + +Required properties: +- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" + for i.MX28 SoC +- reg: Address and length of the register set for the device +- interrupts: Should contain the LRADC interrupts + +Optional properties: +- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen + to LRADC. Valid value is either 4 or 5. If this + property is not present, then the touchscreen is + disabled. 5 wires is valid for i.MX28 SoC only. +- fsl,ave-ctrl: number of samples per direction to calculate an average value. + Allowed value is 1 ... 32, default is 4 +- fsl,ave-delay: delay between consecutive samples. Allowed value is + 2 ... 2048. It is used if 'fsl,ave-ctrl' > 1, counts at + 2 kHz and its default is 2 (= 1 ms) +- fsl,settling: delay between plate switch to next sample. Allowed value is + 1 ... 2047. It counts at 2 kHz and its default is + 10 (= 5 ms) + +Example for i.MX23 SoC: + + lradc@80050000 { + compatible = "fsl,imx23-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <36 37 38 39 40 41 42 43 44>; + status = "okay"; + fsl,lradc-touchscreen-wires = <4>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; + +Example for i.MX28 SoC: + + lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; + status = "okay"; + fsl,lradc-touchscreen-wires = <5>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt index a9a5fe19f..bf99e2f24 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -1,7 +1,11 @@ Rockchip Successive Approximation Register (SAR) A/D Converter bindings Required properties: -- compatible: Should be "rockchip,saradc" or "rockchip,rk3066-tsadc" +- compatible: should be "rockchip,-saradc" or "rockchip,rk3066-tsadc" + - "rockchip,saradc": for rk3188, rk3288 + - "rockchip,rk3066-tsadc": for rk3036 + - "rockchip,rk3399-saradc": for rk3399 + - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/iio/dac/ad5592r.txt b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt new file mode 100644 index 000000000..989f96f31 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5592r.txt @@ -0,0 +1,155 @@ +Analog Devices AD5592R/AD5593R DAC/ADC device driver + +Required properties for the AD5592R: + - compatible: Must be "adi,ad5592r" + - reg: SPI chip select number for the device + - spi-max-frequency: Max SPI frequency to use (< 30000000) + - spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode + +Required properties for the AD5593R: + - compatible: Must be "adi,ad5593r" + - reg: I2C address of the device + +Required properties for all supported chips: + - #address-cells: Should be 1. + - #size-cells: Should be 0. + - channel nodes: + Each child node represents one channel and has the following + Required properties: + * reg: Pin on which this channel is connected to. + * adi,mode: Mode or function of this channel. + Macros specifying the valid values + can be found in . + + The following values are currently supported: + * CH_MODE_UNUSED (the pin is unused) + * CH_MODE_ADC (the pin is ADC input) + * CH_MODE_DAC (the pin is DAC output) + * CH_MODE_DAC_AND_ADC (the pin is DAC output + but can be monitored by an ADC, since + there is no disadvantage this + this should be considered as the + preferred DAC mode) + * CH_MODE_GPIO (the pin is registered + with GPIOLIB) + Optional properties: + * adi,off-state: State of this channel when unused or the + device gets removed. Macros specifying the + valid values can be found in + . + + * CH_OFFSTATE_PULLDOWN (the pin is pulled down) + * CH_OFFSTATE_OUT_LOW (the pin is output low) + * CH_OFFSTATE_OUT_HIGH (the pin is output high) + * CH_OFFSTATE_OUT_TRISTATE (the pin is + tristated output) + + +Optional properties: + - vref-supply: Phandle to the external reference voltage supply. This should + only be set if there is an external reference voltage connected to the VREF + pin. If the property is not set the internal 2.5V reference is used. + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be + asserted during driver probe. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in . + +AD5592R Example: + + #include + + vref: regulator-vref { + compatible = "regulator-fixed"; + regulator-name = "vref-ad559x"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ad5592r@0 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5592r"; + reg = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + vref-supply = <&vref>; /* optional */ + reset-gpios = <&gpio0 86 0>; /* optional */ + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = ; + }; + channel@1 { + reg = <1>; + adi,mode = ; + }; + channel@2 { + reg = <2>; + adi,mode = ; + }; + channel@3 { + reg = <3>; + adi,mode = ; + adi,off-state = ; + }; + channel@4 { + reg = <4>; + adi,mode = ; + adi,off-state = ; + }; + channel@5 { + reg = <5>; + adi,mode = ; + adi,off-state = ; + }; + channel@6 { + reg = <6>; + adi,mode = ; + adi,off-state = ; + }; + channel@7 { + reg = <7>; + adi,mode = ; + adi,off-state = ; + }; + }; + +AD5593R Example: + + #include + + ad5593r@10 { + #size-cells = <0>; + #address-cells = <1>; + #gpio-cells = <2>; + compatible = "adi,ad5593r"; + reg = <0x10>; + gpio-controller; + + channel@0 { + reg = <0>; + adi,mode = ; + adi,off-state = ; + }; + channel@1 { + reg = <1>; + adi,mode = ; + adi,off-state = ; + }; + channel@2 { + reg = <2>; + adi,mode = ; + adi,off-state = ; + }; + channel@6 { + reg = <6>; + adi,mode = ; + adi,off-state = ; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt new file mode 100644 index 000000000..7d6647d4a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt @@ -0,0 +1,20 @@ +NXP LPC1850 DAC bindings + +Required properties: +- compatible: Should be "nxp,lpc1850-dac" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- vref-supply: The regulator supply ADC reference voltage +- resets: phandle to reset controller and line specifier + +Example: +dac: dac@400e1000 { + compatible = "nxp,lpc1850-dac"; + reg = <0x400e1000 0x1000>; + interrupts = <0>; + clocks = <&ccu1 CLK_APB3_DAC>; + vref-supply = <®_vdda>; + resets = <&rgu 42>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index e4d8f1c52..a9fc11e43 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -8,10 +8,23 @@ Required properties: - interrupt-parent : should be the phandle for the interrupt controller - interrupts : interrupt mapping for GPIO IRQ +Optional properties: + - mount-matrix: an optional 3x3 mounting rotation matrix + + Example: mpu6050@68 { compatible = "invensense,mpu6050"; reg = <0x68>; interrupt-parent = <&gpio1>; interrupts = <18 1>; + mount-matrix = "-0.984807753012208", /* x0 */ + "0", /* y0 */ + "-0.173648177666930", /* z0 */ + "0", /* x1 */ + "-1", /* y1 */ + "0", /* z1 */ + "-0.173648177666930", /* x2 */ + "0", /* y2 */ + "0.984807753012208"; /* z2 */ }; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt index 011679f1a..e1e7dd325 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt @@ -8,6 +8,8 @@ Required properties: Optional properties: - gpios : should be device tree identifier of the magnetometer DRDY pin + - vdd-supply: an optional regulator that needs to be on to provide VDD + - mount-matrix: an optional 3x3 mounting rotation matrix Example: @@ -15,4 +17,14 @@ ak8975@0c { compatible = "asahi-kasei,ak8975"; reg = <0x0c>; gpios = <&gpj0 7 0>; + vdd-supply = <&ldo_3v3_gnss>; + mount-matrix = "-0.984807753012208", /* x0 */ + "0", /* y0 */ + "-0.173648177666930", /* z0 */ + "0", /* x1 */ + "-1", /* y1 */ + "0", /* z1 */ + "-0.173648177666930", /* x2 */ + "0", /* y2 */ + "0.984807753012208"; /* z2 */ }; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt b/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt new file mode 100644 index 000000000..df77bf552 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/ds1803.txt @@ -0,0 +1,21 @@ +* Maxim Integrated DS1803 digital potentiometer driver + +The node for this driver must be a child node of a I2C controller, hence +all mandatory properties for your controller must be specified. See directory: + + Documentation/devicetree/bindings/i2c + +for more details. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "maxim,ds1803-010", + "maxim,ds1803-050", + "maxim,ds1803-100" + +Example: +ds1803: ds1803@1 { + reg = <0x28>; + compatible = "maxim,ds1803-010"; +}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt b/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt new file mode 100644 index 000000000..3ccba16f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/mcp4131.txt @@ -0,0 +1,84 @@ +* Microchip MCP413X/414X/415X/416X/423X/424X/425X/426X Digital Potentiometer + driver + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "microchip,mcp4131-502" + "microchip,mcp4131-103" + "microchip,mcp4131-503" + "microchip,mcp4131-104" + "microchip,mcp4132-502" + "microchip,mcp4132-103" + "microchip,mcp4132-503" + "microchip,mcp4132-104" + "microchip,mcp4141-502" + "microchip,mcp4141-103" + "microchip,mcp4141-503" + "microchip,mcp4141-104" + "microchip,mcp4142-502" + "microchip,mcp4142-103" + "microchip,mcp4142-503" + "microchip,mcp4142-104" + "microchip,mcp4151-502" + "microchip,mcp4151-103" + "microchip,mcp4151-503" + "microchip,mcp4151-104" + "microchip,mcp4152-502" + "microchip,mcp4152-103" + "microchip,mcp4152-503" + "microchip,mcp4152-104" + "microchip,mcp4161-502" + "microchip,mcp4161-103" + "microchip,mcp4161-503" + "microchip,mcp4161-104" + "microchip,mcp4162-502" + "microchip,mcp4162-103" + "microchip,mcp4162-503" + "microchip,mcp4162-104" + "microchip,mcp4231-502" + "microchip,mcp4231-103" + "microchip,mcp4231-503" + "microchip,mcp4231-104" + "microchip,mcp4232-502" + "microchip,mcp4232-103" + "microchip,mcp4232-503" + "microchip,mcp4232-104" + "microchip,mcp4241-502" + "microchip,mcp4241-103" + "microchip,mcp4241-503" + "microchip,mcp4241-104" + "microchip,mcp4242-502" + "microchip,mcp4242-103" + "microchip,mcp4242-503" + "microchip,mcp4242-104" + "microchip,mcp4251-502" + "microchip,mcp4251-103" + "microchip,mcp4251-503" + "microchip,mcp4251-104" + "microchip,mcp4252-502" + "microchip,mcp4252-103" + "microchip,mcp4252-503" + "microchip,mcp4252-104" + "microchip,mcp4261-502" + "microchip,mcp4261-103" + "microchip,mcp4261-503" + "microchip,mcp4261-104" + "microchip,mcp4262-502" + "microchip,mcp4262-103" + "microchip,mcp4262-503" + "microchip,mcp4262-104" + +Example: +mcp4131: mcp4131@0 { + compatible = "mcp4131-502"; + reg = <0>; + spi-max-frequency = <500000>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt new file mode 100644 index 000000000..54e7e70bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/hp03.txt @@ -0,0 +1,17 @@ +HopeRF HP03 digital pressure/temperature sensors + +Required properties: +- compatible: must be "hoperf,hp03" +- xclr-gpio: must be device tree identifier of the XCLR pin. + The XCLR pin is a reset of the ADC in the chip, + it must be pulled HI before the conversion and + readout of the value from the ADC registers and + pulled LO afterward. + +Example: + +hp03@0x77 { + compatible = "hoperf,hp03"; + reg = <0x77>; + xclr-gpio = <&portc 0 0x0>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5611.txt b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt new file mode 100644 index 000000000..17bca866c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt @@ -0,0 +1,19 @@ +MEAS ms5611 family pressure sensors + +Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces. + +Required properties: +- compatible: "meas,ms5611" or "meas,ms5607" +- reg: the I2C address or SPI chip select the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. + +Example: + +ms5607@77 { + compatible = "meas,ms5607"; + reg = <0x77>; + vdd-supply = <&ldo_3v3_gnss>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index d4b87cc1e..5844cf728 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -16,6 +16,10 @@ Optional properties: - st,drdy-int-pin: the pin on the package that will be used to signal "data ready" (valid values: 1 or 2). This property is not configurable on all sensors. +- drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share the same + interrupt line. (This binding is taken from pinctrl/pinctrl-bindings.txt) + This is a boolean property. Sensors may also have applicable pin control settings, those use the standard bindings from pinctrl/pinctrl-bindings.txt. @@ -37,6 +41,7 @@ Accelerometers: - st,lsm330-accel - st,lsm303agr-accel - st,lis2dh12-accel +- st,h3lis331dl-accel Gyroscopes: - st,l3g4200d-gyro @@ -46,6 +51,7 @@ Gyroscopes: - st,l3gd20-gyro - st,l3g4is-gyro - st,lsm330-gyro +- st,lsm9ds0-gyro Magnetometers: - st,lsm303agr-magn diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt index c6cfe2e3e..9fc47b006 100644 --- a/Documentation/devicetree/bindings/input/ads7846.txt +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -29,7 +29,7 @@ Optional properties: ti,vref-delay-usecs vref supply delay in usecs, 0 for external vref (u16). ti,vref-mv The VREF voltage, in millivolts (u16). - Set to 0 to use internal refernce + Set to 0 to use internal references (ADS7846). ti,keep-vref-on set to keep vref on for differential measurements as well diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 21641236c..a94940481 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -32,17 +32,17 @@ Optional subnode-properties: Example nodes: - gpio_keys { + gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; autorepeat; - button@21 { + + up { label = "GPIO Key UP"; linux,code = <103>; gpios = <&gpio1 0 1>; }; - button@22 { + + down { label = "GPIO Key DOWN"; linux,code = <108>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt index 34e3382a0..ac5dff412 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -2,11 +2,17 @@ Required properties: - compatible: must be "brcm,iproc-touchscreen" -- reg: physical base address of the controller and length of memory mapped - region. +- ts_syscon: handler of syscon node defining physical base + address of the controller and length of memory mapped region. + If this property is selected please make sure MFD_SYSCON config + is enabled in the defconfig file. - clocks: The clock provided by the SOC to driver the tsc -- clock-name: name for the clock +- clock-names: name for the clock - interrupts: The touchscreen controller's interrupt +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: Specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. Optional properties: - scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. @@ -53,13 +59,18 @@ Optional properties: - touchscreen-inverted-x: X axis is inverted (boolean) - touchscreen-inverted-y: Y axis is inverted (boolean) -Example: +Example: An example of touchscreen node - touchscreen: tsc@0x180A6000 { + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + touchscreen: touchscreen@180A6000 { compatible = "brcm,iproc-touchscreen"; #address-cells = <1>; #size-cells = <1>; - reg = <0x180A6000 0x40>; + ts_syscon = <&ts_adc_syscon>; clocks = <&adc_clk>; clock-names = "tsc_clk"; interrupts = ; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt index cdf05f9b2..abfcab3ed 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -15,7 +15,7 @@ Optional properties: - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value between 1 and 4096. It is the ratio between the internal reference voltage - and the measured voltage after the plate was precharged. Resistence between + and the measured voltage after the plate was precharged. Resistance between plates and therefore the voltage decreases with pressure so that a smaller value is equivalent to a higher pressure. - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 007a5b462..4c29cdab0 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -11,6 +11,8 @@ Main node required properties: - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. Must be a single cell with a value of at least 3. + If the system requires describing PPI affinity, then the value must + be at least 4. The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI interrupts. Other values are reserved for future use. @@ -24,7 +26,14 @@ Main node required properties: 1 = edge triggered 4 = level triggered - Cells 4 and beyond are reserved for future use and must have a value + The 4th cell is a phandle to a node describing a set of CPUs this + interrupt is affine to. The interrupt must be a PPI, and the node + pointed must be a subnode of the "ppi-partitions" subnode. For + interrupt types other than PPI or PPIs that are not partitionned, + this cell must be zero. See the "ppi-partitions" node description + below. + + Cells 5 and beyond are reserved for future use and must have a value of 0 if present. - reg : Specifies base physical address(s) and size of the GIC @@ -50,6 +59,11 @@ Optional Sub-nodes: +PPI affinity can be expressed as a single "ppi-partitions" node, +containing a set of sub-nodes, each with the following property: +- affinity: Should be a list of phandles to CPU nodes (as described in +Documentation/devicetree/bindings/arm/cpus.txt). + GICv3 has one or more Interrupt Translation Services (ITS) that are used to route Message Signalled Interrupts (MSI) to the CPUs. @@ -91,7 +105,7 @@ Examples: gic: interrupt-controller@2c010000 { compatible = "arm,gic-v3"; - #interrupt-cells = <3>; + #interrupt-cells = <4>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -119,4 +133,20 @@ Examples: #msi-cells = <1>; reg = <0x0 0x2c400000 0 0x200000>; }; + + ppi-partitions { + part0: interrupt-partition-0 { + affinity = <&cpu0 &cpu2>; + }; + + part1: interrupt-partition-1 { + affinity = <&cpu1 &cpu3>; + }; + }; + }; + + + device@0 { + reg = <0 0 0 4>; + interrupts = <1 1 4 &part0>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt index c9cf605bb..2a1d16bdf 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt @@ -6,7 +6,7 @@ controllers are OR:ed together and fed to the CPU tile's IRQ input. Each instance can handle up to 32 interrupts. Required properties: -- compatible: "arm,versatile-fpga-irq" +- compatible: "arm,versatile-fpga-irq" or "oxsemi,ox810se-rps-irq" - interrupt-controller: Identifies the node as an interrupt controller - #interrupt-cells: The number of cells to define the interrupts. Must be 1 as the FPGA IRQ controller has no configuration options for interrupt diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt index 2d6c8bb4d..6428a6ba9 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -71,8 +71,8 @@ Bank 1: 24: DMA8 25: DMA9 26: DMA10 -27: DMA11 -28: DMA12 +27: DMA11-14 - shared interrupt for DMA 11 to 14 +28: DMAALL - triggers on all dma interrupts (including chanel 15) 29: AUX 30: ARM 31: VPUDMA diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt new file mode 100644 index 000000000..404090538 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt @@ -0,0 +1,57 @@ +Broadcom BCM6345-style Level 1 interrupt controller + +This block is a first level interrupt controller that is typically connected +directly to one of the HW INT lines on each CPU. + +Key elements of the hardware design include: + +- 32, 64 or 128 incoming level IRQ lines + +- Most onchip peripherals are wired directly to an L1 input + +- A separate instance of the register set for each CPU, allowing individual + peripheral IRQs to be routed to any CPU + +- Contains one or more enable/status word pairs per CPU + +- No atomic set/clear operations + +- No polarity/level/edge settings + +- No FIFO or priority encoder logic; software is expected to read all + 2-4 status words to determine which IRQs are pending + +Required properties: + +- compatible: should be "brcm,bcm-l1-intc", "brcm,bcm6345-l1-intc" +- reg: specifies the base physical address and size of the registers; + the number of supported IRQs is inferred from the size argument +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller(s) + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node; valid values depend on the type of parent interrupt controller + +If multiple reg ranges and interrupt-parent entries are present on an SMP +system, the driver will allow IRQ SMP affinity to be set up through the +/proc/irq/ interface. In the simplest possible configuration, only one +reg range and one interrupt-parent is needed. + +The driver operates in native CPU endian by default, there is no support for +specifying an alternative endianness. + +Example: + +periph_intc: interrupt-controller@10000000 { + compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc"; + reg = <0x10000020 0x20>, + <0x10000040 0x20>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>, <3>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt new file mode 100644 index 000000000..888b2b9f7 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ezchip,nps400-ic.txt @@ -0,0 +1,17 @@ +EZchip NPS Interrupt Controller + +Required properties: + +- compatible : should be "ezchip,nps400-ic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + + +Example: + +intc: interrupt-controller { + compatible = "ezchip,nps400-ic"; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt new file mode 100644 index 000000000..9e3894932 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt @@ -0,0 +1,30 @@ +* Freescale Layerscape SCFG PCIe MSI controller + +Required properties: + +- compatible: should be "fsl,-msi" to identify + Layerscape PCIe MSI controller block such as: + "fsl,1s1021a-msi" + "fsl,1s1043a-msi" +- msi-controller: indicates that this is a PCIe MSI controller node +- reg: physical base address of the controller and length of memory mapped. +- interrupts: an interrupt to the parent interrupt controller. + +Optional properties: +- interrupt-parent: the phandle to the parent interrupt controller. + +This interrupt controller hardware is a second level interrupt controller that +is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based +platforms. If interrupt-parent is not provided, the default parent interrupt +controller will be used. +Each PCIe node needs to have property msi-parent that points to +MSI controller node + +Examples: + + msi1: msi-controller@1571000 { + compatible = "fsl,1s1043a-msi"; + reg = <0x0 0x1571000 0x0 0x8>, + msi-controller; + interrupts = <0 116 0x4>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index b8e1674c7..8cf564d08 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -16,8 +16,7 @@ Required properties: "mediatek,mt6577-sysirq" "mediatek,mt2701-sysirq" - interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Use the same format as specified by GIC in - Documentation/devicetree/bindings/arm/gic.txt +- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt. - interrupt-parent: phandle of irq parent for sysirq. The parent must use the same interrupt-cells format as GIC. - reg: Physical base address of the intpol registers and length of memory diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt deleted file mode 100644 index 1099fe078..000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt +++ /dev/null @@ -1,43 +0,0 @@ -NVIDIA Legacy Interrupt Controller - -All Tegra SoCs contain a legacy interrupt controller that routes -interrupts to the GIC, and also serves as a wakeup source. It is also -referred to as "ictlr", hence the name of the binding. - -The HW block exposes a number of interrupt controllers, each -implementing a set of 32 interrupts. - -Required properties: - -- compatible : should be: "nvidia,tegra-ictlr". The LIC on - subsequent SoCs remained backwards-compatible with Tegra30, so on - Tegra generations later than Tegra30 the compatible value should - include "nvidia,tegra30-ictlr". -- reg : Specifies base physical address and size of the registers. - Each controller must be described separately (Tegra20 has 4 of them, - whereas Tegra30 and later have 5" -- interrupt-controller : Identifies the node as an interrupt controller. -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt source. The value must be 3. -- interrupt-parent : a phandle to the GIC these interrupts are routed - to. - -Notes: - -- Because this HW ultimately routes interrupts to the GIC, the - interrupt specifier must be that of the GIC. -- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs - are explicitly forbidden. - -Example: - - ictlr: interrupt-controller@60004000 { - compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr"; - reg = <0x60004000 64>, - <0x60004100 64>, - <0x60004200 64>, - <0x60004300 64>; - interrupt-controller; - #interrupt-cells = <3>; - interrupt-parent = <&intc>; - }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt new file mode 100644 index 000000000..1099fe078 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt @@ -0,0 +1,43 @@ +NVIDIA Legacy Interrupt Controller + +All Tegra SoCs contain a legacy interrupt controller that routes +interrupts to the GIC, and also serves as a wakeup source. It is also +referred to as "ictlr", hence the name of the binding. + +The HW block exposes a number of interrupt controllers, each +implementing a set of 32 interrupts. + +Required properties: + +- compatible : should be: "nvidia,tegra-ictlr". The LIC on + subsequent SoCs remained backwards-compatible with Tegra30, so on + Tegra generations later than Tegra30 the compatible value should + include "nvidia,tegra30-ictlr". +- reg : Specifies base physical address and size of the registers. + Each controller must be described separately (Tegra20 has 4 of them, + whereas Tegra30 and later have 5" +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : a phandle to the GIC these interrupts are routed + to. + +Notes: + +- Because this HW ultimately routes interrupts to the GIC, the + interrupt specifier must be that of the GIC. +- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs + are explicitly forbidden. + +Example: + + ictlr: interrupt-controller@60004000 { + compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr"; + reg = <0x60004000 64>, + <0x60004100 64>, + <0x60004200 64>, + <0x60004300 64>; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt b/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt index 539adca19..38211f344 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/nxp,lpc3220-mic.txt @@ -1,38 +1,60 @@ -* NXP LPC32xx Main Interrupt Controller - (MIC, including SIC1 and SIC2 secondary controllers) +* NXP LPC32xx MIC, SIC1 and SIC2 Interrupt Controllers Required properties: -- compatible: Should be "nxp,lpc3220-mic" -- interrupt-controller: Identifies the node as an interrupt controller. -- interrupt-parent: Empty for the interrupt controller itself -- #interrupt-cells: The number of cells to define the interrupts. Should be 2. - The first cell is the IRQ number - The second cell is used to specify mode: - 1 = low-to-high edge triggered - 2 = high-to-low edge triggered - 4 = active high level-sensitive - 8 = active low level-sensitive - Default for internal sources should be set to 4 (active high). -- reg: Should contain MIC registers location and length +- compatible: "nxp,lpc3220-mic" or "nxp,lpc3220-sic". +- reg: should contain IC registers location and length. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: the number of cells to define an interrupt, should be 2. + The first cell is the IRQ number, the second cell is used to specify + one of the supported IRQ types: + IRQ_TYPE_EDGE_RISING = low-to-high edge triggered, + IRQ_TYPE_EDGE_FALLING = high-to-low edge triggered, + IRQ_TYPE_LEVEL_HIGH = active high level-sensitive, + IRQ_TYPE_LEVEL_LOW = active low level-sensitive. + Reset value is IRQ_TYPE_LEVEL_LOW. + +Optional properties: +- interrupt-parent: empty for MIC interrupt controller, link to parent + MIC interrupt controller for SIC1 and SIC2 +- interrupts: empty for MIC interrupt controller, cascaded MIC + hardware interrupts for SIC1 and SIC2 Examples: - /* - * MIC - */ + + /* LPC32xx MIC, SIC1 and SIC2 interrupt controllers */ mic: interrupt-controller@40008000 { compatible = "nxp,lpc3220-mic"; + reg = <0x40008000 0x4000>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + sic1: interrupt-controller@4000c000 { + compatible = "nxp,lpc3220-sic"; + reg = <0x4000c000 0x4000>; interrupt-controller; - interrupt-parent; #interrupt-cells = <2>; - reg = <0x40008000 0xC000>; + + interrupt-parent = <&mic>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>, + <30 IRQ_TYPE_LEVEL_LOW>; }; - /* - * ADC - */ + sic2: interrupt-controller@40010000 { + compatible = "nxp,lpc3220-sic"; + reg = <0x40010000 0x4000>; + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&mic>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + }; + + /* ADC */ adc@40048000 { compatible = "nxp,lpc3220-adc"; reg = <0x40048000 0x1000>; - interrupt-parent = <&mic>; - interrupts = <39 4>; + interrupt-parent = <&sic1>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu index 43effa0a4..18d4f407b 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu @@ -4,7 +4,7 @@ All TI OMAP4/5 (and their derivatives) an interrupt controller that routes interrupts to the GIC, and also serves as a wakeup source. It is also referred to as "WUGEN-MPU", hence the name of the binding. -Reguired properties: +Required properties: - compatible : should contain at least "ti,omap4-wugen-mpu" or "ti,omap5-wugen-mpu" @@ -20,7 +20,7 @@ Notes: - Because this HW ultimately routes interrupts to the GIC, the interrupt specifier must be that of the GIC. - Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs - are explicitly forbiden. + are explicitly forbidden. Example: diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index 718074501..19fe6f2c8 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -16,6 +16,7 @@ conditions. "arm,mmu-400" "arm,mmu-401" "arm,mmu-500" + "cavium,smmu-v2" depending on the particular implementation and/or the version of the architecture implemented. diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 68419843e..af10678ea 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -37,6 +37,9 @@ Optional properties for child nodes: property is mandatory for the LEDs in the non-flash modes (e.g. torch or indicator). +- panic-indicator : This property specifies that the LED should be used, + if at all possible, as a panic indicator. + Required properties for flash LED child nodes: - flash-max-microamp : Maximum flash LED supply current in microamperes. - flash-max-timeout-us : Maximum timeout in microseconds after which the flash diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index fea1ebfe2..cbbeb1850 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -23,6 +23,8 @@ LED sub-node properties: property is not present. - retain-state-suspended: (optional) The suspend state can be retained.Such as charge-led gpio. +- panic-indicator : (optional) + see Documentation/devicetree/bindings/leds/common.txt Examples: diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt new file mode 100644 index 000000000..0d501154d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt @@ -0,0 +1,29 @@ +* Analog Devices ADV7180 analog video decoder family + +The adv7180 family devices are used to capture analog video to different +digital interfaces like MIPI CSI-2 or parallel video. + +Required Properties : +- compatible : value must be one of + "adi,adv7180" + "adi,adv7182" + "adi,adv7280" + "adi,adv7280-m" + "adi,adv7281" + "adi,adv7281-m" + "adi,adv7281-ma" + "adi,adv7282" + "adi,adv7282-m" + +Example: + + i2c0@1c22000 { + ... + ... + adv7180@21 { + compatible = "adi,adv7180"; + reg = <0x21>; + }; + ... + }; + diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 619193ccf..6a4e61cbe 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -5,14 +5,22 @@ The rcar_vin device provides video input capabilities for the Renesas R-Car family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - - compatible: Must be one of the following + - compatible: Must be one or more of the following - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device + - "renesas,vin-r8a7792" for the R8A7792 device - "renesas,vin-r8a7791" for the R8A7791 device - "renesas,vin-r8a7790" for the R8A7790 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7778" for the R8A7778 device + - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 compatible device. + - "renesas,rcar-gen3-vin" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: the register base and size for the device registers - interrupts: the interrupt for the device - clocks: Reference to the parent clock @@ -37,7 +45,7 @@ Device node example }; vin0: vin@0xe6ef0000 { - compatible = "renesas,vin-r8a7790"; + compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; clocks = <&mstp8_clks R8A7790_CLK_VIN0>; reg = <0 0xe6ef0000 0 0x1000>; interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt index cbd46fa09..68ac210e6 100644 --- a/Documentation/devicetree/bindings/media/xilinx/video.txt +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -20,7 +20,7 @@ The following properties are common to all Xilinx video IP cores. - xlnx,video-format: This property represents a video format transmitted on an AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream Video IP and System Design Guide" [UG934]. How the format relates to the IP - core is decribed in the IP core bindings documentation. + core is described in the IP core bindings documentation. - xlnx,video-width: This property qualifies the video format with the sample width expressed as a number of bits per pixel component. All components must diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt new file mode 100644 index 000000000..f633b5d0f --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt @@ -0,0 +1,79 @@ +SAMSUNG Exynos SoCs SROM Controller driver. + +Required properties: +- compatible : Should contain "samsung,exynos4210-srom". + +- reg: offset and length of the register set + +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + 0 + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, in addition to regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + +Example: basic definition, no banks are configured + memory-controller@12570000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt deleted file mode 100644 index 3338a2834..000000000 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt +++ /dev/null @@ -1,116 +0,0 @@ -NVIDIA Tegra Memory Controller device tree bindings -=================================================== - -memory-controller node ----------------------- - -Required properties: -- compatible: Should be "nvidia,tegra-mc" -- reg: Physical base address and length of the controller's registers. -- clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - mc: the module's clock input -- interrupts: The interrupt outputs from the controller. -- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines - the SWGROUP of the master. - -This device implements an IOMMU that complies with the generic IOMMU binding. -See ../iommu/iommu.txt for details. - -emc-timings subnode -------------------- - -The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in -register PMC_STRAPPING_OPT_A). - -Required properties for "emc-timings" nodes : -- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is used for. - -timing subnode --------------- - -Each "emc-timings" node should contain a subnode for every supported EMC clock rate. - -Required properties for timing nodes : -- clock-frequency : Should contain the memory clock rate in Hz. -- nvidia,emem-configuration : Values to be written to the EMEM register block. For the Tegra124 SoC -(see section "15.6.1 MC Registers" in the TRM), these are the registers whose values need to be -specified, according to the board documentation: - - MC_EMEM_ARB_CFG - MC_EMEM_ARB_OUTSTANDING_REQ - MC_EMEM_ARB_TIMING_RCD - MC_EMEM_ARB_TIMING_RP - MC_EMEM_ARB_TIMING_RC - MC_EMEM_ARB_TIMING_RAS - MC_EMEM_ARB_TIMING_FAW - MC_EMEM_ARB_TIMING_RRD - MC_EMEM_ARB_TIMING_RAP2PRE - MC_EMEM_ARB_TIMING_WAP2PRE - MC_EMEM_ARB_TIMING_R2R - MC_EMEM_ARB_TIMING_W2W - MC_EMEM_ARB_TIMING_R2W - MC_EMEM_ARB_TIMING_W2R - MC_EMEM_ARB_DA_TURNS - MC_EMEM_ARB_DA_COVERS - MC_EMEM_ARB_MISC0 - MC_EMEM_ARB_MISC1 - MC_EMEM_ARB_RING1_THROTTLE - -Example SoC include file: - -/ { - mc: memory-controller@0,70019000 { - compatible = "nvidia,tegra124-mc"; - reg = <0x0 0x70019000 0x0 0x1000>; - clocks = <&tegra_car TEGRA124_CLK_MC>; - clock-names = "mc"; - - interrupts = ; - - #iommu-cells = <1>; - }; - - sdhci@0,700b0000 { - compatible = "nvidia,tegra124-sdhci"; - ... - iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; - }; -}; - -Example board file: - -/ { - memory-controller@0,70019000 { - emc-timings-3 { - nvidia,ram-code = <3>; - - timing-12750000 { - clock-frequency = <12750000>; - - nvidia,emem-configuration = < - 0x40040001 /* MC_EMEM_ARB_CFG */ - 0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */ - 0x00000001 /* MC_EMEM_ARB_TIMING_RCD */ - 0x00000001 /* MC_EMEM_ARB_TIMING_RP */ - 0x00000002 /* MC_EMEM_ARB_TIMING_RC */ - 0x00000000 /* MC_EMEM_ARB_TIMING_RAS */ - 0x00000002 /* MC_EMEM_ARB_TIMING_FAW */ - 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ - 0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */ - 0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */ - 0x00000003 /* MC_EMEM_ARB_TIMING_R2R */ - 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ - 0x00000003 /* MC_EMEM_ARB_TIMING_R2W */ - 0x00000006 /* MC_EMEM_ARB_TIMING_W2R */ - 0x06030203 /* MC_EMEM_ARB_DA_TURNS */ - 0x000a0402 /* MC_EMEM_ARB_DA_COVERS */ - 0x77e30303 /* MC_EMEM_ARB_MISC0 */ - 0x70000f03 /* MC_EMEM_ARB_MISC1 */ - 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ - >; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt new file mode 100644 index 000000000..ba0bc3f12 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt @@ -0,0 +1,374 @@ +NVIDIA Tegra124 SoC EMC (external memory controller) +==================================================== + +Required properties : +- compatible : Should be "nvidia,tegra124-emc". +- reg : physical base address and length of the controller's registers. +- nvidia,memory-controller : phandle of the MC driver. + +The node should contain a "emc-timings" subnode for each supported RAM type +(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address +being its RAM_CODE. + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is +used for. + +Each "emc-timings" node should contain a "timing" subnode for every supported +EMC clock rate. The "timing" subnodes should have the clock rate in Hz as +their unit address. + +Required properties for "timing" nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- The following properties contain EMC timing characterization values +(specified in the board documentation) : + - nvidia,emc-auto-cal-config : EMC_AUTO_CAL_CONFIG + - nvidia,emc-auto-cal-config2 : EMC_AUTO_CAL_CONFIG2 + - nvidia,emc-auto-cal-config3 : EMC_AUTO_CAL_CONFIG3 + - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL + - nvidia,emc-bgbias-ctl0 : EMC_BGBIAS_CTL0 + - nvidia,emc-cfg : EMC_CFG + - nvidia,emc-cfg-2 : EMC_CFG_2 + - nvidia,emc-ctt-term-ctrl : EMC_CTT_TERM_CTRL + - nvidia,emc-mode-1 : Mode Register 1 + - nvidia,emc-mode-2 : Mode Register 2 + - nvidia,emc-mode-4 : Mode Register 4 + - nvidia,emc-mode-reset : Mode Register 0 + - nvidia,emc-mrs-wait-cnt : EMC_MRS_WAIT_CNT + - nvidia,emc-sel-dpd-ctrl : EMC_SEL_DPD_CTRL + - nvidia,emc-xm2dqspadctrl2 : EMC_XM2DQSPADCTRL2 + - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change + - nvidia,emc-zcal-interval : EMC_ZCAL_INTERVAL +- nvidia,emc-configuration : EMC timing characterization data. These are the +registers (see section "15.6.2 EMC Registers" in the TRM) whose values need to +be specified, according to the board documentation: + + EMC_RC + EMC_RFC + EMC_RFC_SLR + EMC_RAS + EMC_RP + EMC_R2W + EMC_W2R + EMC_R2P + EMC_W2P + EMC_RD_RCD + EMC_WR_RCD + EMC_RRD + EMC_REXT + EMC_WEXT + EMC_WDV + EMC_WDV_MASK + EMC_QUSE + EMC_QUSE_WIDTH + EMC_IBDLY + EMC_EINPUT + EMC_EINPUT_DURATION + EMC_PUTERM_EXTRA + EMC_PUTERM_WIDTH + EMC_PUTERM_ADJ + EMC_CDB_CNTL_1 + EMC_CDB_CNTL_2 + EMC_CDB_CNTL_3 + EMC_QRST + EMC_QSAFE + EMC_RDV + EMC_RDV_MASK + EMC_REFRESH + EMC_BURST_REFRESH_NUM + EMC_PRE_REFRESH_REQ_CNT + EMC_PDEX2WR + EMC_PDEX2RD + EMC_PCHG2PDEN + EMC_ACT2PDEN + EMC_AR2PDEN + EMC_RW2PDEN + EMC_TXSR + EMC_TXSRDLL + EMC_TCKE + EMC_TCKESR + EMC_TPD + EMC_TFAW + EMC_TRPAB + EMC_TCLKSTABLE + EMC_TCLKSTOP + EMC_TREFBW + EMC_FBIO_CFG6 + EMC_ODT_WRITE + EMC_ODT_READ + EMC_FBIO_CFG5 + EMC_CFG_DIG_DLL + EMC_CFG_DIG_DLL_PERIOD + EMC_DLL_XFORM_DQS0 + EMC_DLL_XFORM_DQS1 + EMC_DLL_XFORM_DQS2 + EMC_DLL_XFORM_DQS3 + EMC_DLL_XFORM_DQS4 + EMC_DLL_XFORM_DQS5 + EMC_DLL_XFORM_DQS6 + EMC_DLL_XFORM_DQS7 + EMC_DLL_XFORM_DQS8 + EMC_DLL_XFORM_DQS9 + EMC_DLL_XFORM_DQS10 + EMC_DLL_XFORM_DQS11 + EMC_DLL_XFORM_DQS12 + EMC_DLL_XFORM_DQS13 + EMC_DLL_XFORM_DQS14 + EMC_DLL_XFORM_DQS15 + EMC_DLL_XFORM_QUSE0 + EMC_DLL_XFORM_QUSE1 + EMC_DLL_XFORM_QUSE2 + EMC_DLL_XFORM_QUSE3 + EMC_DLL_XFORM_QUSE4 + EMC_DLL_XFORM_QUSE5 + EMC_DLL_XFORM_QUSE6 + EMC_DLL_XFORM_QUSE7 + EMC_DLL_XFORM_ADDR0 + EMC_DLL_XFORM_ADDR1 + EMC_DLL_XFORM_ADDR2 + EMC_DLL_XFORM_ADDR3 + EMC_DLL_XFORM_ADDR4 + EMC_DLL_XFORM_ADDR5 + EMC_DLL_XFORM_QUSE8 + EMC_DLL_XFORM_QUSE9 + EMC_DLL_XFORM_QUSE10 + EMC_DLL_XFORM_QUSE11 + EMC_DLL_XFORM_QUSE12 + EMC_DLL_XFORM_QUSE13 + EMC_DLL_XFORM_QUSE14 + EMC_DLL_XFORM_QUSE15 + EMC_DLI_TRIM_TXDQS0 + EMC_DLI_TRIM_TXDQS1 + EMC_DLI_TRIM_TXDQS2 + EMC_DLI_TRIM_TXDQS3 + EMC_DLI_TRIM_TXDQS4 + EMC_DLI_TRIM_TXDQS5 + EMC_DLI_TRIM_TXDQS6 + EMC_DLI_TRIM_TXDQS7 + EMC_DLI_TRIM_TXDQS8 + EMC_DLI_TRIM_TXDQS9 + EMC_DLI_TRIM_TXDQS10 + EMC_DLI_TRIM_TXDQS11 + EMC_DLI_TRIM_TXDQS12 + EMC_DLI_TRIM_TXDQS13 + EMC_DLI_TRIM_TXDQS14 + EMC_DLI_TRIM_TXDQS15 + EMC_DLL_XFORM_DQ0 + EMC_DLL_XFORM_DQ1 + EMC_DLL_XFORM_DQ2 + EMC_DLL_XFORM_DQ3 + EMC_DLL_XFORM_DQ4 + EMC_DLL_XFORM_DQ5 + EMC_DLL_XFORM_DQ6 + EMC_DLL_XFORM_DQ7 + EMC_XM2CMDPADCTRL + EMC_XM2CMDPADCTRL4 + EMC_XM2CMDPADCTRL5 + EMC_XM2DQPADCTRL2 + EMC_XM2DQPADCTRL3 + EMC_XM2CLKPADCTRL + EMC_XM2CLKPADCTRL2 + EMC_XM2COMPPADCTRL + EMC_XM2VTTGENPADCTRL + EMC_XM2VTTGENPADCTRL2 + EMC_XM2VTTGENPADCTRL3 + EMC_XM2DQSPADCTRL3 + EMC_XM2DQSPADCTRL4 + EMC_XM2DQSPADCTRL5 + EMC_XM2DQSPADCTRL6 + EMC_DSR_VTTGEN_DRV + EMC_TXDSRVTTGEN + EMC_FBIO_SPARE + EMC_ZCAL_WAIT_CNT + EMC_MRS_WAIT_CNT2 + EMC_CTT + EMC_CTT_DURATION + EMC_CFG_PIPE + EMC_DYN_SELF_REF_CONTROL + EMC_QPOP + +Example SoC include file: + +/ { + emc@7001b000 { + compatible = "nvidia,tegra124-emc"; + reg = <0x0 0x7001b000 0x0 0x1000>; + + nvidia,memory-controller = <&mc>; + }; +}; + +Example board file: + +/ { + emc@7001b000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 /* EMC_RC */ + 0x00000003 /* EMC_RFC */ + 0x00000000 /* EMC_RFC_SLR */ + 0x00000000 /* EMC_RAS */ + 0x00000000 /* EMC_RP */ + 0x00000004 /* EMC_R2W */ + 0x0000000a /* EMC_W2R */ + 0x00000003 /* EMC_R2P */ + 0x0000000b /* EMC_W2P */ + 0x00000000 /* EMC_RD_RCD */ + 0x00000000 /* EMC_WR_RCD */ + 0x00000003 /* EMC_RRD */ + 0x00000003 /* EMC_REXT */ + 0x00000000 /* EMC_WEXT */ + 0x00000006 /* EMC_WDV */ + 0x00000006 /* EMC_WDV_MASK */ + 0x00000006 /* EMC_QUSE */ + 0x00000002 /* EMC_QUSE_WIDTH */ + 0x00000000 /* EMC_IBDLY */ + 0x00000005 /* EMC_EINPUT */ + 0x00000005 /* EMC_EINPUT_DURATION */ + 0x00010000 /* EMC_PUTERM_EXTRA */ + 0x00000003 /* EMC_PUTERM_WIDTH */ + 0x00000000 /* EMC_PUTERM_ADJ */ + 0x00000000 /* EMC_CDB_CNTL_1 */ + 0x00000000 /* EMC_CDB_CNTL_2 */ + 0x00000000 /* EMC_CDB_CNTL_3 */ + 0x00000004 /* EMC_QRST */ + 0x0000000c /* EMC_QSAFE */ + 0x0000000d /* EMC_RDV */ + 0x0000000f /* EMC_RDV_MASK */ + 0x00000060 /* EMC_REFRESH */ + 0x00000000 /* EMC_BURST_REFRESH_NUM */ + 0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */ + 0x00000002 /* EMC_PDEX2WR */ + 0x00000002 /* EMC_PDEX2RD */ + 0x00000001 /* EMC_PCHG2PDEN */ + 0x00000000 /* EMC_ACT2PDEN */ + 0x00000007 /* EMC_AR2PDEN */ + 0x0000000f /* EMC_RW2PDEN */ + 0x00000005 /* EMC_TXSR */ + 0x00000005 /* EMC_TXSRDLL */ + 0x00000004 /* EMC_TCKE */ + 0x00000005 /* EMC_TCKESR */ + 0x00000004 /* EMC_TPD */ + 0x00000000 /* EMC_TFAW */ + 0x00000000 /* EMC_TRPAB */ + 0x00000005 /* EMC_TCLKSTABLE */ + 0x00000005 /* EMC_TCLKSTOP */ + 0x00000064 /* EMC_TREFBW */ + 0x00000000 /* EMC_FBIO_CFG6 */ + 0x00000000 /* EMC_ODT_WRITE */ + 0x00000000 /* EMC_ODT_READ */ + 0x106aa298 /* EMC_FBIO_CFG5 */ + 0x002c00a0 /* EMC_CFG_DIG_DLL */ + 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ + 0x00064000 /* EMC_DLL_XFORM_DQS0 */ + 0x00064000 /* EMC_DLL_XFORM_DQS1 */ + 0x00064000 /* EMC_DLL_XFORM_DQS2 */ + 0x00064000 /* EMC_DLL_XFORM_DQS3 */ + 0x00064000 /* EMC_DLL_XFORM_DQS4 */ + 0x00064000 /* EMC_DLL_XFORM_DQS5 */ + 0x00064000 /* EMC_DLL_XFORM_DQS6 */ + 0x00064000 /* EMC_DLL_XFORM_DQS7 */ + 0x00064000 /* EMC_DLL_XFORM_DQS8 */ + 0x00064000 /* EMC_DLL_XFORM_DQS9 */ + 0x00064000 /* EMC_DLL_XFORM_DQS10 */ + 0x00064000 /* EMC_DLL_XFORM_DQS11 */ + 0x00064000 /* EMC_DLL_XFORM_DQS12 */ + 0x00064000 /* EMC_DLL_XFORM_DQS13 */ + 0x00064000 /* EMC_DLL_XFORM_DQS14 */ + 0x00064000 /* EMC_DLL_XFORM_DQS15 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE0 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE1 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE2 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE3 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR0 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR1 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR2 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR3 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR4 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE8 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE9 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE10 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE11 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE12 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE13 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE14 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE15 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS8 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS9 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS10 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS11 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS12 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS13 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS14 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS15 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ0 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ1 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ2 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ3 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ4 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ5 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ6 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ7 */ + 0x10000280 /* EMC_XM2CMDPADCTRL */ + 0x00000000 /* EMC_XM2CMDPADCTRL4 */ + 0x00111111 /* EMC_XM2CMDPADCTRL5 */ + 0x00000000 /* EMC_XM2DQPADCTRL2 */ + 0x00000000 /* EMC_XM2DQPADCTRL3 */ + 0x77ffc081 /* EMC_XM2CLKPADCTRL */ + 0x00000e0e /* EMC_XM2CLKPADCTRL2 */ + 0x81f1f108 /* EMC_XM2COMPPADCTRL */ + 0x07070004 /* EMC_XM2VTTGENPADCTRL */ + 0x0000003f /* EMC_XM2VTTGENPADCTRL2 */ + 0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */ + 0x51451400 /* EMC_XM2DQSPADCTRL3 */ + 0x00514514 /* EMC_XM2DQSPADCTRL4 */ + 0x00514514 /* EMC_XM2DQSPADCTRL5 */ + 0x51451400 /* EMC_XM2DQSPADCTRL6 */ + 0x0000003f /* EMC_DSR_VTTGEN_DRV */ + 0x00000007 /* EMC_TXDSRVTTGEN */ + 0x00000000 /* EMC_FBIO_SPARE */ + 0x00000042 /* EMC_ZCAL_WAIT_CNT */ + 0x000e000e /* EMC_MRS_WAIT_CNT2 */ + 0x00000000 /* EMC_CTT */ + 0x00000003 /* EMC_CTT_DURATION */ + 0x0000f2f3 /* EMC_CFG_PIPE */ + 0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */ + 0x0000000a /* EMC_QPOP */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt new file mode 100644 index 000000000..8dbe47013 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt @@ -0,0 +1,116 @@ +NVIDIA Tegra Memory Controller device tree bindings +=================================================== + +memory-controller node +---------------------- + +Required properties: +- compatible: Should be "nvidia,tegra-mc" +- reg: Physical base address and length of the controller's registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mc: the module's clock input +- interrupts: The interrupt outputs from the controller. +- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines + the SWGROUP of the master. + +This device implements an IOMMU that complies with the generic IOMMU binding. +See ../iommu/iommu.txt for details. + +emc-timings subnode +------------------- + +The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in +register PMC_STRAPPING_OPT_A). + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is used for. + +timing subnode +-------------- + +Each "emc-timings" node should contain a subnode for every supported EMC clock rate. + +Required properties for timing nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- nvidia,emem-configuration : Values to be written to the EMEM register block. For the Tegra124 SoC +(see section "15.6.1 MC Registers" in the TRM), these are the registers whose values need to be +specified, according to the board documentation: + + MC_EMEM_ARB_CFG + MC_EMEM_ARB_OUTSTANDING_REQ + MC_EMEM_ARB_TIMING_RCD + MC_EMEM_ARB_TIMING_RP + MC_EMEM_ARB_TIMING_RC + MC_EMEM_ARB_TIMING_RAS + MC_EMEM_ARB_TIMING_FAW + MC_EMEM_ARB_TIMING_RRD + MC_EMEM_ARB_TIMING_RAP2PRE + MC_EMEM_ARB_TIMING_WAP2PRE + MC_EMEM_ARB_TIMING_R2R + MC_EMEM_ARB_TIMING_W2W + MC_EMEM_ARB_TIMING_R2W + MC_EMEM_ARB_TIMING_W2R + MC_EMEM_ARB_DA_TURNS + MC_EMEM_ARB_DA_COVERS + MC_EMEM_ARB_MISC0 + MC_EMEM_ARB_MISC1 + MC_EMEM_ARB_RING1_THROTTLE + +Example SoC include file: + +/ { + mc: memory-controller@70019000 { + compatible = "nvidia,tegra124-mc"; + reg = <0x0 0x70019000 0x0 0x1000>; + clocks = <&tegra_car TEGRA124_CLK_MC>; + clock-names = "mc"; + + interrupts = ; + + #iommu-cells = <1>; + }; + + sdhci@700b0000 { + compatible = "nvidia,tegra124-sdhci"; + ... + iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; + }; +}; + +Example board file: + +/ { + memory-controller@70019000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 /* MC_EMEM_ARB_CFG */ + 0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RCD */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RP */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RC */ + 0x00000000 /* MC_EMEM_ARB_TIMING_RAS */ + 0x00000002 /* MC_EMEM_ARB_TIMING_FAW */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */ + 0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2R */ + 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2W */ + 0x00000006 /* MC_EMEM_ARB_TIMING_W2R */ + 0x06030203 /* MC_EMEM_ARB_DA_TURNS */ + 0x000a0402 /* MC_EMEM_ARB_DA_COVERS */ + 0x77e30303 /* MC_EMEM_ARB_MISC0 */ + 0x70000f03 /* MC_EMEM_ARB_MISC1 */ + 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt new file mode 100644 index 000000000..21055e210 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt @@ -0,0 +1,152 @@ +Device tree bindings for OMAP general purpose memory controllers (GPMC) + +The actual devices are instantiated from the child nodes of a GPMC node. + +Required properties: + + - compatible: Should be set to one of the following: + + ti,omap2420-gpmc (omap2420) + ti,omap2430-gpmc (omap2430) + ti,omap3430-gpmc (omap3430 & omap3630) + ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) + ti,am3352-gpmc (am335x devices) + + - reg: A resource specifier for the register space + (see the example below) + - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is + completed. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - gpmc,num-cs: The maximum number of chip-select lines that controller + can support. + - gpmc,num-waitpins: The maximum number of wait pins that controller can + support. + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + 0 + + Currently, calculated values derived from the contents + of the per-CS register GPMC_CONFIG7 (as set up by the + bootloader) are used for the physical address decoding. + As this will change in the future, filling correct + values here is a requirement. + - interrupt-controller: The GPMC driver implements and interrupt controller for + the NAND events "fifoevent" and "termcount" plus the + rising/falling edges on the GPMC_WAIT pins. + The interrupt number mapping is as follows + 0 - NAND_fifoevent + 1 - NAND_termcount + 2 - GPMC_WAIT0 pin edge + 3 - GPMC_WAIT1 pin edge, and so on. + - interrupt-cells: Must be set to 2 + - gpio-controller: The GPMC driver implements a GPIO controller for the + GPMC WAIT pins that can be used as general purpose inputs. + 0 maps to GPMC_WAIT0 pin. + - gpio-cells: Must be set to 2 + +Timing properties for child nodes. All are optional and default to 0. + + - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds + + Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2: + - gpmc,cs-on-ns: Assertion time + - gpmc,cs-rd-off-ns: Read deassertion time + - gpmc,cs-wr-off-ns: Write deassertion time + + ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3: + - gpmc,adv-on-ns: Assertion time + - gpmc,adv-rd-off-ns: Read deassertion time + - gpmc,adv-wr-off-ns: Write deassertion time + - gpmc,adv-aad-mux-on-ns: Assertion time for AAD + - gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD + - gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD + + WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: + - gpmc,we-on-ns Assertion time + - gpmc,we-off-ns: Deassertion time + + OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: + - gpmc,oe-on-ns: Assertion time + - gpmc,oe-off-ns: Deassertion time + - gpmc,oe-aad-mux-on-ns: Assertion time for AAD + - gpmc,oe-aad-mux-off-ns: Deassertion time for AAD + + Access time and cycle time timings (in nanoseconds) corresponding to + GPMC_CONFIG5: + - gpmc,page-burst-access-ns: Multiple access word delay + - gpmc,access-ns: Start-cycle to first data valid delay + - gpmc,rd-cycle-ns: Total read cycle time + - gpmc,wr-cycle-ns: Total write cycle time + - gpmc,bus-turnaround-ns: Turn-around time between successive accesses + - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses + - gpmc,clk-activation-ns: GPMC clock activation time + - gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid + data + +Boolean timing parameters. If property is present parameter enabled and +disabled if omitted: + - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock + - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock + - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive + accesses to a different CS + - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive + accesses to the same CS + - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock + - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock + - gpmc,time-para-granularity: Multiply all access times by 2 + +The following are only applicable to OMAP3+ and AM335x: + - gpmc,wr-access-ns: In synchronous write mode, for single or + burst accesses, defines the number of + GPMC_FCLK cycles from start access time + to the GPMC_CLK rising edge used by the + memory device for the first data capture. + - gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies + the time when the first data is driven on + the address-data bus. + +GPMC chip-select settings properties for child nodes. All are optional. + +- gpmc,burst-length Page/burst length. Must be 4, 8 or 16. +- gpmc,burst-wrap Enables wrap bursting +- gpmc,burst-read Enables read page/burst mode +- gpmc,burst-write Enables write page/burst mode +- gpmc,device-width Total width of device(s) connected to a GPMC + chip-select in bytes. The GPMC supports 8-bit + and 16-bit devices and so this property must be + 1 or 2. +- gpmc,mux-add-data Address and data multiplexing configuration. + Valid values are 1 for address-address-data + multiplexing mode and 2 for address-data + multiplexing mode. +- gpmc,sync-read Enables synchronous read. Defaults to asynchronous + is this is not set. +- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous + is this is not set. +- gpmc,wait-pin Wait-pin used by client. Must be less than + "gpmc,num-waitpins". +- gpmc,wait-on-read Enables wait monitoring on reads. +- gpmc,wait-on-write Enables wait monitoring on writes. + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + /* child nodes go here */ + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt b/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt deleted file mode 100644 index b59c625d6..000000000 --- a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt +++ /dev/null @@ -1,374 +0,0 @@ -NVIDIA Tegra124 SoC EMC (external memory controller) -==================================================== - -Required properties : -- compatible : Should be "nvidia,tegra124-emc". -- reg : physical base address and length of the controller's registers. -- nvidia,memory-controller : phandle of the MC driver. - -The node should contain a "emc-timings" subnode for each supported RAM type -(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address -being its RAM_CODE. - -Required properties for "emc-timings" nodes : -- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is -used for. - -Each "emc-timings" node should contain a "timing" subnode for every supported -EMC clock rate. The "timing" subnodes should have the clock rate in Hz as -their unit address. - -Required properties for "timing" nodes : -- clock-frequency : Should contain the memory clock rate in Hz. -- The following properties contain EMC timing characterization values -(specified in the board documentation) : - - nvidia,emc-auto-cal-config : EMC_AUTO_CAL_CONFIG - - nvidia,emc-auto-cal-config2 : EMC_AUTO_CAL_CONFIG2 - - nvidia,emc-auto-cal-config3 : EMC_AUTO_CAL_CONFIG3 - - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL - - nvidia,emc-bgbias-ctl0 : EMC_BGBIAS_CTL0 - - nvidia,emc-cfg : EMC_CFG - - nvidia,emc-cfg-2 : EMC_CFG_2 - - nvidia,emc-ctt-term-ctrl : EMC_CTT_TERM_CTRL - - nvidia,emc-mode-1 : Mode Register 1 - - nvidia,emc-mode-2 : Mode Register 2 - - nvidia,emc-mode-4 : Mode Register 4 - - nvidia,emc-mode-reset : Mode Register 0 - - nvidia,emc-mrs-wait-cnt : EMC_MRS_WAIT_CNT - - nvidia,emc-sel-dpd-ctrl : EMC_SEL_DPD_CTRL - - nvidia,emc-xm2dqspadctrl2 : EMC_XM2DQSPADCTRL2 - - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change - - nvidia,emc-zcal-interval : EMC_ZCAL_INTERVAL -- nvidia,emc-configuration : EMC timing characterization data. These are the -registers (see section "15.6.2 EMC Registers" in the TRM) whose values need to -be specified, according to the board documentation: - - EMC_RC - EMC_RFC - EMC_RFC_SLR - EMC_RAS - EMC_RP - EMC_R2W - EMC_W2R - EMC_R2P - EMC_W2P - EMC_RD_RCD - EMC_WR_RCD - EMC_RRD - EMC_REXT - EMC_WEXT - EMC_WDV - EMC_WDV_MASK - EMC_QUSE - EMC_QUSE_WIDTH - EMC_IBDLY - EMC_EINPUT - EMC_EINPUT_DURATION - EMC_PUTERM_EXTRA - EMC_PUTERM_WIDTH - EMC_PUTERM_ADJ - EMC_CDB_CNTL_1 - EMC_CDB_CNTL_2 - EMC_CDB_CNTL_3 - EMC_QRST - EMC_QSAFE - EMC_RDV - EMC_RDV_MASK - EMC_REFRESH - EMC_BURST_REFRESH_NUM - EMC_PRE_REFRESH_REQ_CNT - EMC_PDEX2WR - EMC_PDEX2RD - EMC_PCHG2PDEN - EMC_ACT2PDEN - EMC_AR2PDEN - EMC_RW2PDEN - EMC_TXSR - EMC_TXSRDLL - EMC_TCKE - EMC_TCKESR - EMC_TPD - EMC_TFAW - EMC_TRPAB - EMC_TCLKSTABLE - EMC_TCLKSTOP - EMC_TREFBW - EMC_FBIO_CFG6 - EMC_ODT_WRITE - EMC_ODT_READ - EMC_FBIO_CFG5 - EMC_CFG_DIG_DLL - EMC_CFG_DIG_DLL_PERIOD - EMC_DLL_XFORM_DQS0 - EMC_DLL_XFORM_DQS1 - EMC_DLL_XFORM_DQS2 - EMC_DLL_XFORM_DQS3 - EMC_DLL_XFORM_DQS4 - EMC_DLL_XFORM_DQS5 - EMC_DLL_XFORM_DQS6 - EMC_DLL_XFORM_DQS7 - EMC_DLL_XFORM_DQS8 - EMC_DLL_XFORM_DQS9 - EMC_DLL_XFORM_DQS10 - EMC_DLL_XFORM_DQS11 - EMC_DLL_XFORM_DQS12 - EMC_DLL_XFORM_DQS13 - EMC_DLL_XFORM_DQS14 - EMC_DLL_XFORM_DQS15 - EMC_DLL_XFORM_QUSE0 - EMC_DLL_XFORM_QUSE1 - EMC_DLL_XFORM_QUSE2 - EMC_DLL_XFORM_QUSE3 - EMC_DLL_XFORM_QUSE4 - EMC_DLL_XFORM_QUSE5 - EMC_DLL_XFORM_QUSE6 - EMC_DLL_XFORM_QUSE7 - EMC_DLL_XFORM_ADDR0 - EMC_DLL_XFORM_ADDR1 - EMC_DLL_XFORM_ADDR2 - EMC_DLL_XFORM_ADDR3 - EMC_DLL_XFORM_ADDR4 - EMC_DLL_XFORM_ADDR5 - EMC_DLL_XFORM_QUSE8 - EMC_DLL_XFORM_QUSE9 - EMC_DLL_XFORM_QUSE10 - EMC_DLL_XFORM_QUSE11 - EMC_DLL_XFORM_QUSE12 - EMC_DLL_XFORM_QUSE13 - EMC_DLL_XFORM_QUSE14 - EMC_DLL_XFORM_QUSE15 - EMC_DLI_TRIM_TXDQS0 - EMC_DLI_TRIM_TXDQS1 - EMC_DLI_TRIM_TXDQS2 - EMC_DLI_TRIM_TXDQS3 - EMC_DLI_TRIM_TXDQS4 - EMC_DLI_TRIM_TXDQS5 - EMC_DLI_TRIM_TXDQS6 - EMC_DLI_TRIM_TXDQS7 - EMC_DLI_TRIM_TXDQS8 - EMC_DLI_TRIM_TXDQS9 - EMC_DLI_TRIM_TXDQS10 - EMC_DLI_TRIM_TXDQS11 - EMC_DLI_TRIM_TXDQS12 - EMC_DLI_TRIM_TXDQS13 - EMC_DLI_TRIM_TXDQS14 - EMC_DLI_TRIM_TXDQS15 - EMC_DLL_XFORM_DQ0 - EMC_DLL_XFORM_DQ1 - EMC_DLL_XFORM_DQ2 - EMC_DLL_XFORM_DQ3 - EMC_DLL_XFORM_DQ4 - EMC_DLL_XFORM_DQ5 - EMC_DLL_XFORM_DQ6 - EMC_DLL_XFORM_DQ7 - EMC_XM2CMDPADCTRL - EMC_XM2CMDPADCTRL4 - EMC_XM2CMDPADCTRL5 - EMC_XM2DQPADCTRL2 - EMC_XM2DQPADCTRL3 - EMC_XM2CLKPADCTRL - EMC_XM2CLKPADCTRL2 - EMC_XM2COMPPADCTRL - EMC_XM2VTTGENPADCTRL - EMC_XM2VTTGENPADCTRL2 - EMC_XM2VTTGENPADCTRL3 - EMC_XM2DQSPADCTRL3 - EMC_XM2DQSPADCTRL4 - EMC_XM2DQSPADCTRL5 - EMC_XM2DQSPADCTRL6 - EMC_DSR_VTTGEN_DRV - EMC_TXDSRVTTGEN - EMC_FBIO_SPARE - EMC_ZCAL_WAIT_CNT - EMC_MRS_WAIT_CNT2 - EMC_CTT - EMC_CTT_DURATION - EMC_CFG_PIPE - EMC_DYN_SELF_REF_CONTROL - EMC_QPOP - -Example SoC include file: - -/ { - emc@0,7001b000 { - compatible = "nvidia,tegra124-emc"; - reg = <0x0 0x7001b000 0x0 0x1000>; - - nvidia,memory-controller = <&mc>; - }; -}; - -Example board file: - -/ { - emc@0,7001b000 { - emc-timings-3 { - nvidia,ram-code = <3>; - - timing-12750000 { - clock-frequency = <12750000>; - - nvidia,emc-zcal-cnt-long = <0x00000042>; - nvidia,emc-auto-cal-interval = <0x001fffff>; - nvidia,emc-ctt-term-ctrl = <0x00000802>; - nvidia,emc-cfg = <0x73240000>; - nvidia,emc-cfg-2 = <0x000008c5>; - nvidia,emc-sel-dpd-ctrl = <0x00040128>; - nvidia,emc-bgbias-ctl0 = <0x00000008>; - nvidia,emc-auto-cal-config = <0xa1430000>; - nvidia,emc-auto-cal-config2 = <0x00000000>; - nvidia,emc-auto-cal-config3 = <0x00000000>; - nvidia,emc-mode-reset = <0x80001221>; - nvidia,emc-mode-1 = <0x80100003>; - nvidia,emc-mode-2 = <0x80200008>; - nvidia,emc-mode-4 = <0x00000000>; - - nvidia,emc-configuration = < - 0x00000000 /* EMC_RC */ - 0x00000003 /* EMC_RFC */ - 0x00000000 /* EMC_RFC_SLR */ - 0x00000000 /* EMC_RAS */ - 0x00000000 /* EMC_RP */ - 0x00000004 /* EMC_R2W */ - 0x0000000a /* EMC_W2R */ - 0x00000003 /* EMC_R2P */ - 0x0000000b /* EMC_W2P */ - 0x00000000 /* EMC_RD_RCD */ - 0x00000000 /* EMC_WR_RCD */ - 0x00000003 /* EMC_RRD */ - 0x00000003 /* EMC_REXT */ - 0x00000000 /* EMC_WEXT */ - 0x00000006 /* EMC_WDV */ - 0x00000006 /* EMC_WDV_MASK */ - 0x00000006 /* EMC_QUSE */ - 0x00000002 /* EMC_QUSE_WIDTH */ - 0x00000000 /* EMC_IBDLY */ - 0x00000005 /* EMC_EINPUT */ - 0x00000005 /* EMC_EINPUT_DURATION */ - 0x00010000 /* EMC_PUTERM_EXTRA */ - 0x00000003 /* EMC_PUTERM_WIDTH */ - 0x00000000 /* EMC_PUTERM_ADJ */ - 0x00000000 /* EMC_CDB_CNTL_1 */ - 0x00000000 /* EMC_CDB_CNTL_2 */ - 0x00000000 /* EMC_CDB_CNTL_3 */ - 0x00000004 /* EMC_QRST */ - 0x0000000c /* EMC_QSAFE */ - 0x0000000d /* EMC_RDV */ - 0x0000000f /* EMC_RDV_MASK */ - 0x00000060 /* EMC_REFRESH */ - 0x00000000 /* EMC_BURST_REFRESH_NUM */ - 0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */ - 0x00000002 /* EMC_PDEX2WR */ - 0x00000002 /* EMC_PDEX2RD */ - 0x00000001 /* EMC_PCHG2PDEN */ - 0x00000000 /* EMC_ACT2PDEN */ - 0x00000007 /* EMC_AR2PDEN */ - 0x0000000f /* EMC_RW2PDEN */ - 0x00000005 /* EMC_TXSR */ - 0x00000005 /* EMC_TXSRDLL */ - 0x00000004 /* EMC_TCKE */ - 0x00000005 /* EMC_TCKESR */ - 0x00000004 /* EMC_TPD */ - 0x00000000 /* EMC_TFAW */ - 0x00000000 /* EMC_TRPAB */ - 0x00000005 /* EMC_TCLKSTABLE */ - 0x00000005 /* EMC_TCLKSTOP */ - 0x00000064 /* EMC_TREFBW */ - 0x00000000 /* EMC_FBIO_CFG6 */ - 0x00000000 /* EMC_ODT_WRITE */ - 0x00000000 /* EMC_ODT_READ */ - 0x106aa298 /* EMC_FBIO_CFG5 */ - 0x002c00a0 /* EMC_CFG_DIG_DLL */ - 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ - 0x00064000 /* EMC_DLL_XFORM_DQS0 */ - 0x00064000 /* EMC_DLL_XFORM_DQS1 */ - 0x00064000 /* EMC_DLL_XFORM_DQS2 */ - 0x00064000 /* EMC_DLL_XFORM_DQS3 */ - 0x00064000 /* EMC_DLL_XFORM_DQS4 */ - 0x00064000 /* EMC_DLL_XFORM_DQS5 */ - 0x00064000 /* EMC_DLL_XFORM_DQS6 */ - 0x00064000 /* EMC_DLL_XFORM_DQS7 */ - 0x00064000 /* EMC_DLL_XFORM_DQS8 */ - 0x00064000 /* EMC_DLL_XFORM_DQS9 */ - 0x00064000 /* EMC_DLL_XFORM_DQS10 */ - 0x00064000 /* EMC_DLL_XFORM_DQS11 */ - 0x00064000 /* EMC_DLL_XFORM_DQS12 */ - 0x00064000 /* EMC_DLL_XFORM_DQS13 */ - 0x00064000 /* EMC_DLL_XFORM_DQS14 */ - 0x00064000 /* EMC_DLL_XFORM_DQS15 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE0 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE1 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE2 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE3 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR0 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR1 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR2 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR3 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR4 */ - 0x00000000 /* EMC_DLL_XFORM_ADDR5 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE8 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE9 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE10 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE11 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE12 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE13 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE14 */ - 0x00000000 /* EMC_DLL_XFORM_QUSE15 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS8 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS9 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS10 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS11 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS12 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS13 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS14 */ - 0x00000000 /* EMC_DLI_TRIM_TXDQS15 */ - 0x000fc000 /* EMC_DLL_XFORM_DQ0 */ - 0x000fc000 /* EMC_DLL_XFORM_DQ1 */ - 0x000fc000 /* EMC_DLL_XFORM_DQ2 */ - 0x000fc000 /* EMC_DLL_XFORM_DQ3 */ - 0x0000fc00 /* EMC_DLL_XFORM_DQ4 */ - 0x0000fc00 /* EMC_DLL_XFORM_DQ5 */ - 0x0000fc00 /* EMC_DLL_XFORM_DQ6 */ - 0x0000fc00 /* EMC_DLL_XFORM_DQ7 */ - 0x10000280 /* EMC_XM2CMDPADCTRL */ - 0x00000000 /* EMC_XM2CMDPADCTRL4 */ - 0x00111111 /* EMC_XM2CMDPADCTRL5 */ - 0x00000000 /* EMC_XM2DQPADCTRL2 */ - 0x00000000 /* EMC_XM2DQPADCTRL3 */ - 0x77ffc081 /* EMC_XM2CLKPADCTRL */ - 0x00000e0e /* EMC_XM2CLKPADCTRL2 */ - 0x81f1f108 /* EMC_XM2COMPPADCTRL */ - 0x07070004 /* EMC_XM2VTTGENPADCTRL */ - 0x0000003f /* EMC_XM2VTTGENPADCTRL2 */ - 0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */ - 0x51451400 /* EMC_XM2DQSPADCTRL3 */ - 0x00514514 /* EMC_XM2DQSPADCTRL4 */ - 0x00514514 /* EMC_XM2DQSPADCTRL5 */ - 0x51451400 /* EMC_XM2DQSPADCTRL6 */ - 0x0000003f /* EMC_DSR_VTTGEN_DRV */ - 0x00000007 /* EMC_TXDSRVTTGEN */ - 0x00000000 /* EMC_FBIO_SPARE */ - 0x00000042 /* EMC_ZCAL_WAIT_CNT */ - 0x000e000e /* EMC_MRS_WAIT_CNT2 */ - 0x00000000 /* EMC_CTT */ - 0x00000003 /* EMC_CTT_DURATION */ - 0x0000f2f3 /* EMC_CFG_PIPE */ - 0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */ - 0x0000000a /* EMC_QPOP */ - >; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 9b30011ec..a6e2ea411 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -1,6 +1,6 @@ Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs -These devices are audio SoCs with extensive digital capabilites and a range +These devices are audio SoCs with extensive digital capabilities and a range of analogue I/O. Required properties: diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index fd39fa545..d20b1034e 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -6,10 +6,11 @@ axp202 (X-Powers) axp209 (X-Powers) axp221 (X-Powers) axp223 (X-Powers) +axp809 (X-Powers) Required properties: - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", - "x-powers,axp221", "x-powers,axp223" + "x-powers,axp221", "x-powers,axp223", "x-powers,axp809" - reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin @@ -18,7 +19,9 @@ Required properties: Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz - (range: 750-1875). Default: 1.5MHz + AXP152/20X: range: 750-1875, Default: 1.5 MHz + AXP22X/80X: range: 1800-4050, Default: 3 MHz + - -supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -77,6 +80,30 @@ LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +AXP809 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply + Example: axp209: pmic@34 { diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt new file mode 100644 index 000000000..05485699d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -0,0 +1,27 @@ +Hisilicon Hi655x Power Management Integrated Circuit (PMIC) + +The hardware layout for access PMIC Hi655x from AP SoC Hi6220. +Between PMIC Hi655x and Hi6220, the physical signal channel is SSI. +We can use memory-mapped I/O to communicate. + ++----------------+ +-------------+ +| | | | +| Hi6220 | SSI bus | Hi655x | +| |-------------| | +| |(REGMAP_MMIO)| | ++----------------+ +-------------+ + +Required properties: +- compatible: Should be "hisilicon,hi655x-pmic". +- reg: Base address of PMIC on Hi6220 SoC. +- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). +- pmic-gpios: The GPIO used by PMIC IRQ. + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + } diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 000000000..2ad44f7e4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,143 @@ +MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" + "maxim,max20024". +- reg: I2C device address. + +Optional properties: +------------------- +- interrupts: The interrupt on the parent the controller is + connected to. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: is <2> and their usage is compliant to the 2 cells + variant of <../interrupt-controller/interrupts.txt> + IRQ numbers for different interrupt source of MAX77620 + are defined at dt-bindings/mfd/max77620.h. + +Optional subnodes and their properties: +======================================= + +Flexible power sequence configurations: +-------------------------------------- +The Flexible Power Sequencer (FPS) allows each regulator to power up under +hardware or software control. Additionally, each regulator can power on +independently or among a group of other regulators with an adjustable power-up +and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed +to be part of a sequence allowing external regulators to be sequenced along +with internal regulators. 32KHz clock can be programmed to be part of a +sequence. + +The flexible sequencing structure consists of two hardware enable inputs +(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2. +Each master sequencing timer is programmable through its configuration +register to have a hardware enable source (EN1 or EN2) or a software enable +source (SW). When enabled/disabled, the master sequencing timer generates +eight sequencing events on different time periods called slots. The time +period between each event is programmable within the configuration register. +Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power +sequence slave register which allows its enable source to be specified as +a flexible power sequencer timer or a software bit. When a FPS source of +regulators, GPIOs and clocks specifies the enable source to be a flexible +power sequencer, the power up and power down delays can be specified in +the regulators, GPIOs and clocks flexible power sequencer configuration +registers. + +When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz +clock are set into following state at the sequencing event that +corresponds to its flexible sequencer configuration register. + Sleep state: In this state, regulators, GPIOs + and 32KHz clock get disabled at + the sequencing event. + Global Low Power Mode (GLPM): In this state, regulators are set in + low power mode at the sequencing event. + +The configuration parameters of FPS is provided through sub-node "fps" +and their child for FPS specific. The child node name for FPS are "fps0", +"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively. + +The FPS configurations like FPS source, power up and power down slots for +regulators, GPIOs and 32kHz clocks are provided in their respective +configuration nodes which is explained in respective sub-system DT +binding document. + +There is need for different FPS configuration parameters based on system +state like when system state changed from active to suspend or active to +power off (shutdown). + +Optional properties: +------------------- +-maxim,fps-event-source: u32, FPS event source like external + hardware input to PMIC i.e. EN0, EN1 or + software (SW). + The macros are defined on + dt-bindings/mfd/max77620.h + for different control source. + - MAX77620_FPS_EVENT_SRC_EN0 + for hardware input pin EN0. + - MAX77620_FPS_EVENT_SRC_EN1 + for hardware input pin EN1. + - MAX77620_FPS_EVENT_SRC_SW + for software control. + +-maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to shutdown + state. + +-maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to suspend state. + +-maxim,device-state-on-disabled-event: u32, describe the PMIC state when FPS + event cleared (set to LOW) whether it + should go to sleep state or low-power + state. Following are valid values: + - MAX77620_FPS_INACTIVE_STATE_SLEEP + to set the PMIC state to sleep. + - MAX77620_FPS_INACTIVE_STATE_LOW_POWER + to set the PMIC state to low + power. + Absence of this property or other value + will not change device state when FPS + event get cleared. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +For DT binding details of different sub modules like GPIO, pincontrol, +regulator, power, please refer respective device-tree binding document +under their respective sub-system directories. + +Example: +-------- +#include + +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + fps { + fps0 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = ; + }; + + fps1 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = ; + }; + + fps2 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = ; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt index 5e97a9593..b98b291a3 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -178,7 +178,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional (default if no other qcom,force-mode is specified) Value type: - Defintion: indicates that the regulator should be forced to a + Definition: indicates that the regulator should be forced to a particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode @@ -204,7 +204,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional Value type: - Defintion: indicates that the regulator should not be forced to any + Definition: indicates that the regulator should not be forced to any particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt index 7bab90cc4..4a7e030e4 100644 --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -4,7 +4,8 @@ Required properties: - compatible: "brcm,bcm3384", "brcm,bcm33843" "brcm,bcm3384-viper", "brcm,bcm33843-viper" - "brcm,bcm6328", "brcm,bcm6368", + "brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6368", + "brcm,bcm63168", "brcm,bcm63268", "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu3.txt b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt new file mode 100644 index 000000000..616862ad2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit v3 + +Properties: +- compatible: "cavium,octeon-7890-ciu3" + + Compatibility with 78XX and 73XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is source number. + The second cell indicates the triggering semantics, and may have a + value of either 4 for level semantics, or 1 for edge semantics. + +Example: + interrupt-controller@1010000000000 { + compatible = "cavium,octeon-7890-ciu3"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Source number (20 significant bits) + * 2) Trigger type: (4 == level, 1 == edge) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10100 0x00000000 0x0 0xb0000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt index fc149f326..f080f06da 100644 --- a/Documentation/devicetree/bindings/mips/cpu_irq.txt +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -13,7 +13,7 @@ Required properties: - compatible : Should be "mti,cpu-interrupt-controller" Example devicetree: - cpu-irq: cpu-irq@0 { + cpu-irq: cpu-irq { #address-cells = <0>; interrupt-controller; diff --git a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt index c7a26ca8d..6611a7c20 100644 --- a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt +++ b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt @@ -30,11 +30,90 @@ Required properties: region may not be present in some scenarios, such as in the device tree presented to a virtual machine. + - msi-parent + Value type: + Definition: Must be present and point to the MSI controller node + handling message interrupts for the MC. + + - ranges + Value type: + Definition: A standard property. Defines the mapping between the child + MC address space and the parent system address space. + + The MC address space is defined by 3 components: + + + Valid values for region type are + 0x0 - MC portals + 0x1 - QBMAN portals + + - #address-cells + Value type: + Definition: Must be 3. (see definition in 'ranges' property) + + - #size-cells + Value type: + Definition: Must be 1. + +Sub-nodes: + + The fsl-mc node may optionally have dpmac sub-nodes that describe + the relationship between the Ethernet MACs which belong to the MC + and the Ethernet PHYs on the system board. + + The dpmac nodes must be under a node named "dpmacs" which contains + the following properties: + + - #address-cells + Value type: + Definition: Must be present if dpmac sub-nodes are defined and must + have a value of 1. + + - #size-cells + Value type: + Definition: Must be present if dpmac sub-nodes are defined and must + have a value of 0. + + These nodes must have the following properties: + + - compatible + Value type: + Definition: Must be "fsl,qoriq-mc-dpmac". + + - reg + Value type: + Definition: Specifies the id of the dpmac. + + - phy-handle + Value type: + Definition: Specifies the phandle to the PHY device node associated + with the this dpmac. + Example: fsl_mc: fsl-mc@80c000000 { compatible = "fsl,qoriq-mc"; reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ - }; + msi-parent = <&its>; + #address-cells = <3>; + #size-cells = <1>; + + /* + * Region type 0x0 - MC portals + * Region type 0x1 - QBMAN portals + */ + ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000 + 0x1 0x0 0x0 0x8 0x18000000 0x8000000>; + dpmacs { + #address-cells = <1>; + #size-cells = <0>; + + dpmac@1 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <1>; + phy-handle = <&mdio0_phy0>; + } + } + }; diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt index 71ad57e05..3149297b3 100644 --- a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -20,7 +20,7 @@ Example: compatible = "microchip,pic32mzda-sdhci"; reg = <0x1f8ec000 0x100>; interrupts = <191 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&REFCLKO4>, <&PBCLK5>; + clocks = <&rootclk REF4CLK>, <&rootclk PB5CLK>; clock-names = "base_clk", "sys_clk"; bus-width = <4>; cap-sd-highspeed; diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt index 0cb827bf9..3d965d57e 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt @@ -1,7 +1,7 @@ * The simple eMMC hardware reset provider The purpose of this driver is to perform standard eMMC hw reset -procedure, as descibed by Jedec 4.4 specification. This procedure is +procedure, as described by Jedec 4.4 specification. This procedure is performed just after MMC core enabled power to the given mmc host (to fix possible issues if bootloader has left eMMC card in initialized or unknown state), and before performing complete system reboot (also in diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index ea5614b6f..07184e8f8 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -15,6 +15,7 @@ Required Properties: - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 + - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 Optional Properties: * clocks: from common clock binding: if ciu_drive and ciu_sample are diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 18d950df2..88faa9112 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -38,7 +38,7 @@ Optional properties: - bus-width: Number of data lines. See: Documentation/devicetree/bindings/mmc/mmc.txt. -- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for +- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for configuring the CCONFIG3 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. @@ -48,7 +48,7 @@ Optional properties: - vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd supply in eMMC/SD specs. -- sd-uhs--sdr50: To enable the SDR50 in the mmcss. +- sd-uhs-sdr50: To enable the SDR50 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. - sd-uhs-sdr104: To enable the SDR104 in the mmcss. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 7fb746dd1..0f610d4b5 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,3 +26,6 @@ Required properties: Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable +- pinctrl-names: should be "default", "state_uhs" +- pinctrl-0: should contain default/high speed pin ctrl +- pinctrl-1: should contain uhs mode pin ctrl diff --git a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt index 8babdaa86..6d1b7971d 100644 --- a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt +++ b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt @@ -12,6 +12,12 @@ Optional properties: - vmmc-supply: a phandle of a regulator, supplying Vcc to the card - vqmmc-supply: a phandle of a regulator, supplying VccQ to the card +- pinctrl-names: Can contain a "default" entry and a "state_uhs" + entry. The state_uhs entry is used together with the default + entry when the board requires distinct settings for UHS speeds. + +- pinctrl-N: One property for each name listed in pinctrl-names, see + ../pinctrl/pinctrl-bindings.txt. Additionally any standard mmc bindings from mmc.txt can be used. diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt index beace4b89..4ec28796a 100644 --- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt +++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt @@ -1,8 +1,26 @@ Flash device on ARM Versatile board +These flash chips are found in the ARM reference designs like Integrator, +Versatile, RealView, Versatile Express etc. + +They are regular CFI compatible (Intel or AMD extended) flash chips with +some special write protect/VPP bits that can be controlled by the machine's +system controller. + Required properties: -- compatible : must be "arm,versatile-flash"; +- compatible : must be "arm,versatile-flash", "cfi-flash"; +- reg : memory address for the flash chip - bank-width : width in bytes of flash interface. +For the rest of the properties, see mtd-physmap.txt. + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. + +Example: + +flash@34000000 { + compatible = "arm,versatile-flash", "cfi-flash"; + reg = <0x34000000 0x4000000>; + bank-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index d53aba98f..3e7ee99d3 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -39,7 +39,7 @@ Optional properties: Nand Flash Controller(NFC) is an optional sub-node Required properties: -- compatible : "atmel,sama5d3-nfc" or "atmel,sama5d4-nfc". +- compatible : "atmel,sama5d3-nfc". - reg : should specify the address and size used for NFC command registers, NFC registers and NFC SRAM. NFC SRAM address and size can be absent if don't want to use it. diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index c2546ced9..7066597c9 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -24,6 +24,7 @@ Required properties: brcm,brcmnand-v5.0 brcm,brcmnand-v6.0 brcm,brcmnand-v6.1 + brcm,brcmnand-v6.2 brcm,brcmnand-v7.0 brcm,brcmnand-v7.1 brcm,brcmnand @@ -52,7 +53,7 @@ Optional properties: v7.0. Use this property to describe the rare earlier versions of this core that include WP - -- Additonal SoC-specific NAND controller properties -- + -- Additional SoC-specific NAND controller properties -- The NAND controller is integrated differently on the variety of SoCs on which it is found. Part of this integration involves providing status and enable bits diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 0333ec87d..c34aa6f8a 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -5,7 +5,8 @@ Required properties: "fsl,imx7d-qspi", "fsl,imx6ul-qspi", "fsl,ls1021a-qspi" or - "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi" + "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi", + "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index fb733c4e1..3ee7e2026 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -13,7 +13,11 @@ Documentation/devicetree/bindings/mtd/nand.txt Required properties: - - reg: The CS line the peripheral is connected to + - compatible: "ti,omap2-nand" + - reg: range id (CS number), base offset and length of the + NAND I/O space + - interrupt-parent: must point to gpmc node + - interrupts: Two interrupt specifiers, one for fifoevent, one for termcount. Optional properties: @@ -44,6 +48,7 @@ Optional properties: locating ECC errors for BCHx algorithms. SoC devices which have ELM hardware engines should specify this device node in .dtsi Using ELM for ECC error correction frees some CPU cycles. + - rb-gpios: GPIO specifier for the ready/busy# pin. For inline partition table parsing (optional): @@ -55,20 +60,26 @@ Example for an AM33xx board: gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; - reg = <0x50000000 0x1000000>; + reg = <0x50000000 0x36c>; interrupts = <100>; gpmc,num-cs = <8>; gpmc,num-waitpins = <2>; #address-cells = <2>; #size-cells = <1>; - ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + ranges = <0 0 0x08000000 0x1000000>; /* CS0 space, 16MB */ elm_id = <&elm>; + interrupt-controller; + #interrupt-cells = <2>; nand@0,0 { - reg = <0 0 0>; /* CS0, offset 0 */ + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* CS0, offset 0, NAND I/O window 4 */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>; nand-bus-width = <16>; ti,nand-ecc-opt = "bch8"; ti,nand-xfer-type = "polled"; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index b53f92e25..3733300de 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -1,8 +1,31 @@ -* MTD generic binding +* NAND chip and NAND controller generic binding + +NAND controller/NAND chip representation: + +The NAND controller should be represented with its own DT node, and all +NAND chips attached to this controller should be defined as children nodes +of the NAND controller. This representation should be enforced even for +simple controllers supporting only one chip. + +Mandatory NAND controller properties: +- #address-cells: depends on your controller. Should at least be 1 to + encode the CS line id. +- #size-cells: depends on your controller. Put zero unless you need a + mapping between CS lines and dedicated memory regions + +Optional NAND controller properties +- ranges: only needed if you need to define a mapping between CS lines and + memory regions + +Optional NAND chip properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode. - Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", - "soft_bch". + Supported values are: "none", "soft", "hw", "hw_syndrome", + "hw_oob_first". + Deprecated values: + "soft_bch": use "soft" and nand-ecc-algo instead +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values are: "hamming", "bch". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -19,3 +42,20 @@ errors per {size} bytes". The interpretation of these parameters is implementation-defined, so not all implementations must support all possible combinations. However, implementations are encouraged to further specify the value(s) they support. + +Example: + + nand-controller { + #address-cells = <1>; + #size-cells = <0>; + + /* controller specific properties */ + + nand@0 { + reg = <0>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + + /* controller specific properties */ + }; + }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index 078060a97..05f705e32 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -18,6 +18,8 @@ Required properties for all the ethernet interfaces: - First is the Rx interrupt. This irq is mandatory. - Second is the Tx completion interrupt. This is supported only on SGMII based 1GbE and 10GbE interfaces. +- channel: Ethernet to CPU, start channel (prefetch buffer) number + - Must map to the first irq and irqs must be sequential - port-id: Port number (0 or 1) - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 5fdbbcdf8..9f4807f90 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -31,8 +31,6 @@ A switch child node has the following optional property: switch. Must be set if the switch can not detect the presence and/or size of a connected EEPROM, otherwise optional. -- reset-gpios : phandle and specifier to a gpio line connected to - reset pin of the switch chip. A switch may have multiple "port" children nodes diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt new file mode 100644 index 000000000..762918939 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -0,0 +1,35 @@ +Marvell DSA Switch Device Tree Bindings +--------------------------------------- + +WARNING: This binding is currently unstable. Do not program it into a +FLASH never to be changed again. Once this binding is stable, this +warning will be removed. + +If you need a stable binding, use the old dsa.txt binding. + +Marvell Switches are MDIO devices. The following properties should be +placed as a child node of an mdio device. + +The properties described here are those specific to Marvell devices. +Additional required and optional properties can be found in dsa.txt. + +Required properties: +- compatible : Should be one of "marvell,mv88e6085", +- reg : Address on the MII bus for the switch. + +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line + +Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index ecacfa44b..d4b7f2e49 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -7,19 +7,45 @@ Required properties: - mode: dsa fabric mode string. only support one of dsaf modes like these: "2port-64vf", "6port-16rss", - "6port-16vf". + "6port-16vf", + "single-port". - interrupt-parent: the interrupt parent of this device. - interrupts: should contain the DSA Fabric and rcb interrupt. - reg: specifies base physical address(es) and size of the device registers. - The first region is external interface control register base and size. - The second region is SerDes base register and size. + The first region is external interface control register base and size(optional, + only used when subctrl-syscon does not exist). It is recommended using + subctrl-syscon rather than this address. + The second region is SerDes base register and size(optional, only used when + serdes-syscon in port node does not exist). It is recommended using + serdes-syscon rather than this address. The third region is the PPE register base and size. - The fourth region is dsa fabric base register and size. - The fifth region is cpld base register and size, it is not required if do not use cpld. -- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1]. + The fourth region is dsa fabric base register and size. It is not required for + single-port mode. +- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the + corresponding reg's index. + +- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional + attribute. If port node exists, phy-handle in each port node will be used. + see ethernet.txt [1]. +- subctrl-syscon: is syscon handle for external interface control register. +- reset-field-offset: is offset of reset field. Its value depends on the hardware + user manual. - buf-size: rx buffer size, should be 16-1024. - desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. +- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending + on mode of dsaf). Port node contain some attributes listed below: +- reg: is physical port index in one dsaf. +- phy-handle: phy handle of physical port. It is not required if there isn't + phy device. see ethernet.txt [1]. +- serdes-syscon: is syscon handle for SerDes register. +- cpld-syscon: is syscon handle + register offset pair for cpld register. It is + not required if there isn't cpld device. +- port-rst-offset: is offset of reset field for each port in dsaf. Its value + depends on the hardware user manual. +- port-mode-offset: is offset of port mode field for each port in dsaf. Its + value depends on the hardware user manual. + [1] Documentation/devicetree/bindings/net/phy.txt Example: @@ -28,11 +54,11 @@ dsaf0: dsa@c7000000 { compatible = "hisilicon,hns-dsaf-v1"; mode = "6port-16rss"; interrupt-parent = <&mbigen_dsa>; - reg = <0x0 0xC0000000 0x0 0x420000 - 0x0 0xC2000000 0x0 0x300000 - 0x0 0xc5000000 0x0 0x890000 + reg = <0x0 0xc5000000 0x0 0x890000 0x0 0xc7000000 0x0 0x60000>; - phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>; + reg-names = "ppe-base", "dsaf-base"; + subctrl-syscon = <&subctrl>; + reset-field-offset = 0; interrupts = <131 4>,<132 4>, <133 4>,<134 4>, <135 4>,<136 4>, <137 4>,<138 4>, <139 4>,<140 4>, <141 4>,<142 4>, @@ -43,4 +69,15 @@ dsaf0: dsa@c7000000 { buf-size = <4096>; desc-num = <1024>; dma-coherent; + + port@0 { + reg = 0; + phy-handle = <&phy0>; + serdes-syscon = <&serdes>; + }; + + port@1 { + reg = 1; + serdes-syscon = <&serdes>; + }; }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index e6a9d1c30..f0421ee3c 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -8,7 +8,7 @@ Required properties: specifies a reference to the associating hardware driver node. see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt - port-id: is the index of port provided by DSAF (the accelerator). DSAF can - connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They + connect to 8 PHYs. Port 0 to 1 are both used for administration purpose. They are called debug ports. The remaining 6 PHYs are taken according to the mode of DSAF. @@ -36,6 +36,34 @@ Required properties: | | | | | | external port + This attribute is remained for compatible purpose. It is not recommended to + use it in new code. + +- port-idx-in-ae: is the index of port provided by AE. + In NIC mode of DSAF, all 6 PHYs of service DSAF are taken as ethernet ports + to the CPU. The port-idx-in-ae can be 0 to 5. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug debug service + port port port + (0) (0) (0-5) + + In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical + ports connected to a LAN Switch while the CPU side assume itself have one + single NIC connected to this switch. In this case, the port-idx-in-ae + will be 0 only. + +-----+-----+------+------+ + | CPU | + +-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | service| port(0) + debug debug +------------+ + port port | switch | + (0) (0) +-+-+-+-+-+-++ + | | | | | | + external port + - local-mac-address: mac addr of the ethernet interface Example: @@ -43,6 +71,6 @@ Example: ethernet@0{ compatible = "hisilicon,hns-nic-v1"; ae-handle = <&dsaf0>; - port-id = <0>; + port-idx-in-ae = <0>; local-mac-address = [a2 14 e4 4b 56 76]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt new file mode 100644 index 000000000..6a9a63cb0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt @@ -0,0 +1,56 @@ +Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices +------ + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897-bt" + * "marvell,sd8997-bt" + +Optional properties: + + - marvell,cal-data: Calibration data downloaded to the device during + initialization. This is an array of 28 values(u8). + + - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. + firmware will use the pin to wakeup host system (u16). + - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host + platform. The value will be configured to firmware. This + is needed to work chip's sleep feature as expected (u16). + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. Driver will request an irq based + on this interrupt number. During system suspend, the irq will be + enabled so that the bluetooth chip can wakeup host platform under + certain condition. During system resume, the irq will be disabled + to make sure unnecessary interrupt is not received. + +Example: + +IRQ pin 119 is used as system wakeup source interrupt. +wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host +using this device side pin and wakeup latency. +calibration data is also available in below example. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + btmrvl: bluetooth@2 { + compatible = "marvell,sd8897-bt"; + reg = <2>; + interrupt-parent = <&pio>; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + + marvell,cal-data = /bits/ 8 < + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0xf0 0x00>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt new file mode 100644 index 000000000..1dc3bc755 --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt @@ -0,0 +1,59 @@ +* Microchip ENC28J60 + +This is a standalone 10 MBit ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be "microchip,enc28j60" +- reg: Specify the SPI chip select the ENC28J60 is wired to +- interrupt-parent: Specify the phandle of the source interrupt, see interrupt + binding documentation for details. Usually this is the GPIO bank + the interrupt line is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. The ENC28J60 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60. + According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for NXP i.MX28 with pin control stuff for GPIO irq): + + ssp2: ssp@80014000 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>; + status = "okay"; + + enc28j60: ethernet@0 { + compatible = "microchip,enc28j60"; + pinctrl-names = "default"; + pinctrl-0 = <&enc28j60_pins>; + reg = <0>; + interrupt-parent = <&gpio3>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <12000000>; + }; + }; + + pinctrl@80018000 { + enc28j60_pins: enc28j60_pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt new file mode 100644 index 000000000..1aea822d4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt @@ -0,0 +1,31 @@ +* NXP Semiconductors PN532 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn532-i2c" or "nxp,pn533-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN532 on I2C2): + +&i2c2 { + + status = "okay"; + + pn532: pn532@24 { + + compatible = "nxp,pn532-i2c"; + + reg = <0x24>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + }; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 6605d1960..95816c5fc 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -51,14 +51,16 @@ Optional properties: AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface - snps,xit_frm: unlock on WoL - - snps,wr_osr_lmt: max write oustanding req. limit - - snps,rd_osr_lmt: max read oustanding req. limit + - snps,wr_osr_lmt: max write outstanding req. limit + - snps,rd_osr_lmt: max read outstanding req. limit - snps,kbbe: do not cross 1KiB boundary. - snps,axi_all: align address - snps,blen: this is a vector of supported burst length. - snps,fb: fixed-burst - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst + - snps,tso: this enables the TSO feature otherwise it will be managed by + MAC HW capability register. - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 58d935b58..5d21141a6 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -2,7 +2,7 @@ Required properties: - reg - The ID number for the phy, usually a small integer - - ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h + - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt new file mode 100644 index 000000000..c421aba0a --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt @@ -0,0 +1,63 @@ +Marvell 8897/8997 (sd8897/sd8997) SDIO devices +------ + +This node provides properties for controlling the marvell sdio wireless device. +The node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897" + * "marvell,sd8997" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 96aae6b4f..74d7f0af2 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -5,12 +5,18 @@ Required properties: * "qcom,ath10k" * "qcom,ipq4019-wifi" -PCI based devices uses compatible string "qcom,ath10k" and takes only -calibration data via "qcom,ath10k-calibration-data". Rest of the properties -are not applicable for PCI based devices. +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" -and also uses most of the properties defined in this doc. +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. Optional properties: - reg: Address and length of the register set for the device. @@ -35,8 +41,11 @@ Optional properties: - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into MSI address register. -- qcom,ath10k-calibration-data : calibration data as an array, the - length can vary between hw versions +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. Example (to supply the calibration data alone): @@ -105,5 +114,5 @@ wifi0: wifi@a000000 { "legacy"; qcom,msi_addr = <0x0b006040>; qcom,msi_base = <0x40>; - qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; }; diff --git a/Documentation/devicetree/bindings/numa.txt b/Documentation/devicetree/bindings/numa.txt new file mode 100644 index 000000000..21b35053c --- /dev/null +++ b/Documentation/devicetree/bindings/numa.txt @@ -0,0 +1,275 @@ +============================================================================== +NUMA binding description. +============================================================================== + +============================================================================== +1 - Introduction +============================================================================== + +Systems employing a Non Uniform Memory Access (NUMA) architecture contain +collections of hardware resources including processors, memory, and I/O buses, +that comprise what is commonly known as a NUMA node. +Processor accesses to memory within the local NUMA node is generally faster +than processor accesses to memory outside of the local NUMA node. +DT defines interfaces that allow the platform to convey NUMA node +topology information to OS. + +============================================================================== +2 - numa-node-id +============================================================================== + +For the purpose of identification, each NUMA node is associated with a unique +token known as a node id. For the purpose of this binding +a node id is a 32-bit integer. + +A device node is associated with a NUMA node by the presence of a +numa-node-id property which contains the node id of the device. + +Example: + /* numa node 0 */ + numa-node-id = <0>; + + /* numa node 1 */ + numa-node-id = <1>; + +============================================================================== +3 - distance-map +============================================================================== + +The optional device tree node distance-map describes the relative +distance (memory latency) between all numa nodes. + +- compatible : Should at least contain "numa-distance-map-v1". + +- distance-matrix + This property defines a matrix to describe the relative distances + between all numa nodes. + It is represented as a list of node pairs and their relative distance. + + Note: + 1. Each entry represents distance from first node to second node. + The distances are equal in either direction. + 2. The distance from a node to self (local distance) is represented + with value 10 and all internode distance should be represented with + a value greater than 10. + 3. distance-matrix should have entries in lexicographical ascending + order of nodes. + 4. There must be only one device node distance-map which must + reside in the root node. + 5. If the distance-map node is not present, a default + distance-matrix is used. + +Example: + 4 nodes connected in mesh/ring topology as below, + + 0_______20______1 + | | + | | + 20 20 + | | + | | + |_______________| + 3 20 2 + + if relative distance for each hop is 20, + then internode distance would be, + 0 -> 1 = 20 + 1 -> 2 = 20 + 2 -> 3 = 20 + 3 -> 0 = 20 + 0 -> 2 = 40 + 1 -> 3 = 40 + + and dt presentation for this distance matrix is, + + distance-map { + compatible = "numa-distance-map-v1"; + distance-matrix = <0 0 10>, + <0 1 20>, + <0 2 40>, + <0 3 20>, + <1 0 20>, + <1 1 10>, + <1 2 20>, + <1 3 40>, + <2 0 40>, + <2 1 20>, + <2 2 10>, + <2 3 20>, + <3 0 20>, + <3 1 40>, + <3 2 20>, + <3 3 10>; + }; + +============================================================================== +4 - Example dts +============================================================================== + +Dual socket system consists of 2 boards connected through ccn bus and +each board having one socket/soc of 8 cpus, memory and pci bus. + + memory@c00000 { + device_type = "memory"; + reg = <0x0 0xc00000 0x0 0x80000000>; + /* node 0 */ + numa-node-id = <0>; + }; + + memory@10000000000 { + device_type = "memory"; + reg = <0x100 0x0 0x0 0x80000000>; + /* node 1 */ + numa-node-id = <1>; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0>; + enable-method = "psci"; + /* node 0 */ + numa-node-id = <0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x1>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@2 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x2>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@3 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x3>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@4 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x4>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@5 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x5>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@6 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x6>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@7 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x7>; + enable-method = "psci"; + numa-node-id = <0>; + }; + cpu@8 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x8>; + enable-method = "psci"; + /* node 1 */ + numa-node-id = <1>; + }; + cpu@9 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x9>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@a { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xa>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@b { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xb>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@c { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xc>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@d { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xd>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@e { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xe>; + enable-method = "psci"; + numa-node-id = <1>; + }; + cpu@f { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0xf>; + enable-method = "psci"; + numa-node-id = <1>; + }; + }; + + pcie0: pcie0@848000000000 { + compatible = "arm,armv8"; + device_type = "pci"; + bus-range = <0 255>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x8480 0x00000000 0 0x10000000>; /* Configuration space */ + ranges = <0x03000000 0x8010 0x00000000 0x8010 0x00000000 0x70 0x00000000>; + /* node 0 */ + numa-node-id = <0>; + }; + + pcie1: pcie1@948000000000 { + compatible = "arm,armv8"; + device_type = "pci"; + bus-range = <0 255>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x9480 0x00000000 0 0x10000000>; /* Configuration space */ + ranges = <0x03000000 0x9010 0x00000000 0x9010 0x00000000 0x70 0x00000000>; + /* node 1 */ + numa-node-id = <1>; + }; + + distance-map { + compatible = "numa-distance-map-v1"; + distance-matrix = <0 0 10>, + <0 1 20>, + <1 1 10>; + }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 601256fe8..ee91cbdd9 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -45,7 +45,7 @@ Devices supporting OPPs must set their "operating-points-v2" property with phandle to a OPP table in their DT node. The OPP core will use this phandle to find the operating points for the device. -If required, this can be extended for SoC vendor specfic bindings. Such bindings +If required, this can be extended for SoC vendor specific bindings. Such bindings should be documented as Documentation/devicetree/bindings/power/-opp.txt and should have a compatible description like: "operating-points-v2-". diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 64f2fff12..6c5322c55 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -31,7 +31,7 @@ Optional properties: Example configuration: - pcie: pcie@0xdffff000 { + pcie: pcie@dffff000 { compatible = "snps,dw-pcie"; reg = <0xdffff000 0x1000>, /* Controller registers */ <0xd0000000 0x2000>; /* PCI config space */ diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 3be80c689..83aeb1f5a 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "fsl,imx6q-pcie" -- reg: base addresse and length of the pcie controller +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie" +- reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: @@ -19,6 +19,20 @@ Optional properties: - fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" Example: diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index b721beacf..59c2f47aa 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -34,11 +34,11 @@ Hip05 Example (note that Hip06 is the same except compatible): ranges = <0x82000000 0 0x00000000 0x220 0x00000000 0 0x10000000>; num-lanes = <8>; port-id = <1>; - #interrupts-cells = <1>; - interrupts-map-mask = <0xf800 0 0 7>; - interrupts-map = <0x0 0 0 1 &mbigen_pcie 1 10 - 0x0 0 0 2 &mbigen_pcie 2 11 - 0x0 0 0 3 &mbigen_pcie 3 12 - 0x0 0 0 4 &mbigen_pcie 4 13>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie 1 10 + 0x0 0 0 2 &mbigen_pcie 2 11 + 0x0 0 0 3 &mbigen_pcie 3 12 + 0x0 0 0 4 &mbigen_pcie 4 13>; status = "ok"; }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 75321ae23..b8cc395ff 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -60,11 +60,14 @@ Required properties: - afi - pcie_x -Required properties on Tegra124 and later: +Required properties on Tegra124 and later (deprecated): - phys: Must contain an entry for each entry in phy-names. - phy-names: Must include the following entries: - pcie +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -122,11 +125,22 @@ Required properties: - Root port 0 uses 4 lanes, root port 1 is unused. - Both root ports use 2 lanes. -Example: +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. Note that the number + of entries does not have to (though usually will) be equal to the specified + number of lanes in the nvidia,num-lanes property. Entries are of the form + "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. + +Examples: +========= + +Tegra20: +-------- SoC DTSI: - pcie-controller { + pcie-controller@80003000 { compatible = "nvidia,tegra20-pcie"; device_type = "pci"; reg = <0x80003000 0x00000800 /* PADS registers */ @@ -186,10 +200,9 @@ SoC DTSI: }; }; - Board DTS: - pcie-controller { + pcie-controller@80003000 { status = "okay"; vdd-supply = <&pci_vdd_reg>; @@ -222,3 +235,204 @@ if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, device nodes need to be added in order to allow the bus' children to be instantiated at the proper location in the operating system's device tree (as illustrated by the optional nodes in the example above). + +Tegra30: +-------- + +SoC DTSI: + + pcie-controller@00003000 { + compatible = "nvidia,tegra30-pcie"; + device_type = "pci"; + reg = <0x00003000 0x00000800 /* PADS registers */ + 0x00003800 0x00000200 /* AFI registers */ + 0x10000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = ; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ + 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ + + clocks = <&tegra_car TEGRA30_CLK_PCIE>, + <&tegra_car TEGRA30_CLK_AFI>, + <&tegra_car TEGRA30_CLK_PLL_E>, + <&tegra_car TEGRA30_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@00003000 { + status = "okay"; + + avdd-pexa-supply = <&ldo1_reg>; + vdd-pexa-supply = <&ldo1_reg>; + avdd-pexb-supply = <&ldo1_reg>; + vdd-pexb-supply = <&ldo1_reg>; + avdd-pex-pll-supply = <&ldo1_reg>; + avdd-plle-supply = <&ldo1_reg>; + vddio-pex-ctl-supply = <&sys_3v3_reg>; + hvdd-pex-supply = <&sys_3v3_pexs_reg>; + + pci@1,0 { + status = "okay"; + }; + + pci@3,0 { + status = "okay"; + }; + }; + +Tegra124: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra124-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = , /* controller interrupt */ + ; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA124_CLK_PCIE>, + <&tegra_car TEGRA124_CLK_AFI>, + <&tegra_car TEGRA124_CLK_PLL_E>, + <&tegra_car TEGRA124_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-supply = <&vdd_3v3_lp0>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + vddio-pex-ctl-supply = <&vdd_3v3_lp0>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + + /* Mini PCIe */ + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + + /* Gigabit Ethernet */ + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt new file mode 100644 index 000000000..598533a57 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -0,0 +1,38 @@ +* Marvell Armada 7K/8K PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "marvell,armada8k-pcie" +- reg: must contain two register regions + - the control register region + - the config space region +- reg-names: + - "ctrl" for the control register region + - "config" for the config space region +- interrupts: Interrupt specifier for the PCIe controler +- clocks: reference to the PCIe controller clock + +Example: + + pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 /* downstream I/O */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; /* non-prefetchable memory */ + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = ; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 54eae2938..d08a4d511 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -56,6 +56,7 @@ Optional properties:- phy-names: name of the Generic Keystine SerDes phy for PCI - If boot loader already does PCI link establishment, then phys and phy-names shouldn't be present. + interrupts: platform interrupt for error interrupts. Designware DT Properties not applicable for Keystone PCI diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt new file mode 100644 index 000000000..a7aee9ea8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt @@ -0,0 +1,21 @@ +Driver for Broadcom Northstar USB 2.0 PHY + +Required properties: +- compatible: brcm,ns-usb2-phy +- reg: iomem address range of DMU (Device Management Unit) +- reg-names: "dmu", the only needed & supported reg right now +- clocks: USB PHY reference clock +- clock-names: "phy-ref-clk", the only needed & supported clock right now + +To initialize USB 2.0 PHY driver needs to setup PLL correctly. To do this it +requires passing phandle to the USB PHY reference clock. + +Example: + usb2-phy { + compatible = "brcm,ns-usb2-phy"; + reg = <0x1800c000 0x1000>; + reg-names = "dmu"; + #phy-cells = <0>; + clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>; + clock-names = "phy-ref-clk"; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt deleted file mode 100644 index d87ab7c12..000000000 --- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt +++ /dev/null @@ -1,41 +0,0 @@ -* Broadcom SATA3 PHY for STB - -Required properties: -- compatible: should be one or more of - "brcm,bcm7425-sata-phy" - "brcm,bcm7445-sata-phy" - "brcm,phy-sata3" -- address-cells: should be 1 -- size-cells: should be 0 -- reg: register range for the PHY PCB interface -- reg-names: should be "phy" - -Sub-nodes: - Each port's PHY should be represented as a sub-node. - -Sub-nodes required properties: -- reg: the PHY number -- phy-cells: generic PHY binding; must be 0 -Optional: -- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port - - -Example: - - sata-phy@f0458100 { - compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; - reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - - sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - - sata-phy@1 { - reg = <1>; - #phy-cells = <0>; - }; - }; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt new file mode 100644 index 000000000..d0231209d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -0,0 +1,44 @@ +* Broadcom SATA3 PHY + +Required properties: +- compatible: should be one or more of + "brcm,bcm7425-sata-phy" + "brcm,bcm7445-sata-phy" + "brcm,iproc-ns2-sata-phy" + "brcm,phy-sata3" +- address-cells: should be 1 +- size-cells: should be 0 +- reg: register ranges for the PHY PCB interface +- reg-names: should be "phy" and "phy-ctrl" + The "phy-ctrl" registers are only required for + "brcm,iproc-ns2-sata-phy". + +Sub-nodes: + Each port's PHY should be represented as a sub-node. + +Sub-nodes required properties: +- reg: the PHY number +- phy-cells: generic PHY binding; must be 0 + +Sub-nodes optional properties: +- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port + This property is not applicable for "brcm,iproc-ns2-sata-phy". + +Example: + sata-phy@f0458100 { + compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; + reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; + reg-names = "phy"; + #address-cells = <1>; + #size-cells = <0>; + + sata-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + sata-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt new file mode 100644 index 000000000..0bf1ae243 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -0,0 +1,733 @@ +Device tree binding for NVIDIA Tegra XUSB pad controller +======================================================== + +The Tegra XUSB pad controller manages a set of I/O lanes (with differential +signals) which connect directly to pins/pads on the SoC package. Each lane +is controlled by a HW block referred to as a "pad" in the Tegra hardware +documentation. Each such "pad" may control either one or multiple lanes, +and thus contains any logic common to all its lanes. Each lane can be +separately configured and powered up. + +Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or +super-speed USB. Other lanes are for various types of low-speed, full-speed +or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller +contains a software-configurable mux that sits between the I/O controller +ports (e.g. PCIe) and the lanes. + +In addition to per-lane configuration, USB 3.0 ports may require additional +settings on a per-board basis. + +Pads will be represented as children of the top-level XUSB pad controller +device tree node. Each lane exposed by the pad will be represented by its +own subnode and can be referenced by users of the lane using the standard +PHY bindings, as described by the phy-bindings.txt file in this directory. + +The Tegra hardware documentation refers to the connection between the XUSB +pad controller and the XUSB controller as "ports". This is confusing since +"port" is typically used to denote the physical USB receptacle. The device +tree binding in this document uses the term "port" to refer to the logical +abstraction of the signals that are routed to a USB receptacle (i.e. a PHY +for the USB signal, the VBUS power supply, the USB 2.0 companion port for +USB 3.0 receptacles, ...). + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb-padctl" + - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl" + - Tegra210: "nvidia,tegra210-xusb-padctl" +- reg: Physical base address and length of the controller's registers. +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must include the following entries: + - "padctl" + + +Pad nodes: +========== + +A required child node named "pads" contains a list of subnodes, one for each +of the pads exposed by the XUSB pad controller. Each pad may need additional +resources that can be referenced in its pad node. + +The "status" property is used to enable or disable the use of a pad. If set +to "disabled", the pad will not be used on the given board. In order to use +the pad and any of its lanes, this property must be set to "okay". + +For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie +and sata. No extra resources are required for operation of these pads. + +For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is +a description of the properties of each pad. + +UTMI pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the USB2 tracking clock + +HSIC pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the HSIC tracking clock + +PCIe pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "pll": phandle and specifier referring to the PLLE +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the PCIe UPHY block + +SATA pad: +--------- + +Required properties: +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the SATA UPHY block + + +PHY nodes: +========== + +Each pad node has a child named "lanes" that contains one or more children of +its own, each representing one of the lanes controlled by the pad. + +Required properties: +-------------------- +- status: Defines the operation status of the PHY. Valid values are: + - "disabled": the PHY is disabled + - "okay": the PHY is enabled +- #phy-cells: Should be 0. Since each lane represents a single PHY, there is + no need for an additional specifier. +- nvidia,function: The output function of the PHY. See below for a list of + valid functions per SoC generation. + +For Tegra124 and Tegra132, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2 + - functions: "snps", "xusb", "uart" +- ulpi: ulpi-0 + - functions: "snps", "xusb" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4 + - functions: "pcie", "usb3-ss" +- sata: sata-0 + - functions: "usb3-ss", "sata" + +For Tegra210, the list of valid PHY nodes is given below: +- utmi: utmi-0, utmi-1, utmi-2, utmi-3 + - functions: "snps", "xusb", "uart" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6 + - functions: "pcie-x1", "usb3-ss", "pcie-x4" +- sata: sata-0 + - functions: "usb3-ss", "sata" + + +Port nodes: +=========== + +A required child node named "ports" contains a list of all the ports exposed +by the XUSB pad controller. Per-port configuration is only required for USB. + +USB2 ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- mode: A string that determines the mode in which to run the port. Valid + values are: + - "host": for USB host mode + - "device": for USB device mode + - "otg": for USB OTG mode + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +ULPI ports: +----------- + +Optional properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +HSIC ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled + +Optional properties: +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +Super-speed USB ports: +---------------------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,usb2-companion: A single cell that specifies the physical port number + to map this super-speed USB port to. The range of valid port numbers varies + with the SoC generation: + - 0-2: for Tegra124 and Tegra132 + - 0-3: for Tegra210 + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. + +For Tegra124 and Tegra132, the XUSB pad controller exposes the following +ports: +- 3x USB2: usb2-0, usb2-1, usb2-2 +- 1x ULPI: ulpi-0 +- 2x HSIC: hsic-0, hsic-1 +- 2x super-speed USB: usb3-0, usb3-1 + +For Tegra210, the XUSB pad controller exposes the following ports: +- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 +- 2x HSIC: hsic-0, hsic-1 +- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 + + +Examples: +========= + +Tegra124 and Tegra132: +---------------------- + +SoC include: + + padctl@7009f000 { + /* for Tegra124 */ + compatible = "nvidia,tegra124-xusb-padctl"; + /* for Tegra132 */ + compatible = "nvidia,tegra132-xusb-padctl", + "nvidia,tegra124-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + pads { + usb2 { + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + ulpi { + status = "disabled"; + + lanes { + ulpi-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + ulpi-0 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + /* Micro A/B */ + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + /* Mini PCIe */ + usb2-1 { + status = "okay"; + mode = "host"; + }; + + /* USB3 */ + usb2-2 { + status = "okay"; + mode = "host"; + + vbus-supply = <&vdd_usb3_vbus>; + }; + + usb3-0 { + nvidia,port = <2>; + status = "okay"; + }; + }; + }; + +Tegra210: +--------- + +SoC include: + + padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + status = "disabled"; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-5 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-6 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-3 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + status = "okay"; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + usb2-1 { + status = "okay"; + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + status = "okay"; + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + status = "okay"; + mode = "host"; + }; + + usb3-0 { + status = "okay"; + nvidia,lanes = "pcie-6"; + nvidia,port = <1>; + }; + + usb3-1 { + status = "okay"; + nvidia,lanes = "pcie-5"; + nvidia,port = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt index bd61b467e..3bb821cd6 100644 --- a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt +++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt @@ -18,7 +18,7 @@ creg: syscon@40043000 { compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; reg = <0x40043000 0x1000>; - usb0_otg_phy: phy@004 { + usb0_otg_phy: phy { compatible = "nxp,lpc1850-usb-otg-phy"; clocks = <&ccu1 CLK_USB0>; #phy-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt index 00100cf3e..33a2b1ee3 100644 --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -4,7 +4,9 @@ mt65xx USB3.0 PHY binding This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. Required properties (controller (parent) node): - - compatible : should be "mediatek,mt8173-u3phy" + - compatible : should be one of + "mediatek,mt2701-u3phy" + "mediatek,mt8173-u3phy" - reg : offset and length of register for phy, exclude port's register. - clocks : a list of phandle + clock-specifier pairs, one for each diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt index 00944a05e..744b48095 100644 --- a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt @@ -17,7 +17,7 @@ Example: usb2_phy: usb2phy@0 { compatible = "st,stih416-usb-phy"; - #phy-cell = <0>; + #phy-cells = <0>; st,syscfg = <&syscfg_rear>; clocks = <&clk_sysin>; clock-names = "osc_phy"; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index d564ba4f1..91da947ae 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -7,6 +7,12 @@ Required properties: - compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the register block. - #address-cells: number of address cells for the USB channel subnodes, must be <1>. @@ -34,7 +40,7 @@ the USB channel; see the selector meanings below: Example (Lager board): usb-phy@e6590100 { - compatible = "renesas,usb-phy-r8a7790"; + compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy"; reg = <0 0xe6590100 0 0x100>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index eaf7e9b7c..2281d6cde 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -6,6 +6,12 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the partial USB 2.0 Host register block. - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. @@ -15,18 +21,20 @@ To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are combined, the device tree node should set interrupt properties to use the channel as USB OTG: - interrupts: interrupt specifier for the PHY. +- vbus-supply: Phandle to a regulator that provides power to the VBUS. This + regulator will be managed during the PHY power on/off sequence. Example (R-Car H3): usb-phy@ee080200 { - compatible = "renesas,usb2-phy-r8a7795"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee080200 0 0x700>; interrupts = ; clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; usb-phy@ee0a0200 { - compatible = "renesas,usb2-phy-r8a7795"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee0a0200 0 0x700>; clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 0289d3b07..9872ba854 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -2,9 +2,20 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,s5pv210-mipi-video-phy"; +- compatible : should be one of the listed compatibles: + - "samsung,s5pv210-mipi-video-phy" + - "samsung,exynos5420-mipi-video-phy" + - "samsung,exynos5433-mipi-video-phy" - #phy-cells : from the generic phy bindings, must be 1; -- syscon - phandle to the PMU system controller; + +In case of s5pv210 and exynos5420 compatible PHYs: +- syscon - phandle to the PMU system controller + +In case of exynos5433 compatible PHY: + - samsung,pmu-syscon - phandle to the PMU system controller + - samsung,disp-sysreg - phandle to the DISP system registers controller + - samsung,cam0-sysreg - phandle to the CAM0 system registers controller + - samsung,cam1-sysreg - phandle to the CAM1 system registers controller For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in the PHY specifier identifies the PHY and its meaning is as follows: @@ -12,6 +23,9 @@ the PHY specifier identifies the PHY and its meaning is as follows: 1 - MIPI DSIM 0, 2 - MIPI CSIS 1, 3 - MIPI DSIM 1. +"samsung,exynos5420-mipi-video-phy" and "samsung,exynos5433-mipi-video-phy" +supports additional fifth PHY: + 4 - MIPI CSIS 2. Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt index 4b5efa51b..29b72e303 100644 --- a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -34,7 +34,7 @@ pic32_pinctrl: pinctrl@1f801400{ #size-cells = <1>; compatible = "microchip,pic32mzda-pinctrl"; reg = <0x1f801400 0x400>; - clocks = <&PBCLK1>; + clocks = <&rootclk PB1CLK>; pinctrl_uart2: pinctrl_uart2 { uart2-tx { diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt index 30676ded8..4048f43a9 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt @@ -1,6 +1,12 @@ Device tree binding for NVIDIA Tegra XUSB pad controller ======================================================== +NOTE: It turns out that this binding isn't an accurate description of the XUSB +pad controller. While the description is good enough for the functional subset +required for PCIe and SATA, it lacks the flexibility to represent the features +needed for USB. For the new binding, see ../phy/nvidia,tegra-xusb-padctl.txt. +The binding described in this file is deprecated and should not be used. + The Tegra XUSB pad controller manages a set of lanes, each of which can be assigned to one out of a set of different pads. Some of these pads have an associated PHY that must be powered up before the pad can be used. @@ -79,7 +85,7 @@ Example: SoC file extract: ----------------- - padctl@0,7009f000 { + padctl@7009f000 { compatible = "nvidia,tegra124-xusb-padctl"; reg = <0x0 0x7009f000 0x0 0x1000>; resets = <&tegra_car 142>; @@ -91,7 +97,7 @@ SoC file extract: Board file extract: ------------------- - pcie-controller@0,01003000 { + pcie-controller@01003000 { ... phys = <&padctl 0>; @@ -102,7 +108,7 @@ Board file extract: ... - padctl: padctl@0,7009f000 { + padctl: padctl@7009f000 { pinctrl-0 = <&padctl_default>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index a90c812ad..a54c39ebb 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -122,7 +122,7 @@ to specify in a pin configuration subnode: 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5) 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5) 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30) - If this property is ommited 30uA strength will be used if + If this property is omitted 30uA strength will be used if pull up is selected - bias-high-impedance: diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index ffadb7a37..74e6ec033 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -72,8 +72,8 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that -have a configurable I/O voltage, the power-source value should be the +bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For +pins that have a configurable I/O voltage, the power-source value should be the nominal I/O voltage in millivolts. diff --git a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt index 0e6d8754e..747899223 100644 --- a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt +++ b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt @@ -29,7 +29,7 @@ IC (PMIC) - qcom,charger-disable: Usage: optional Value type: - Definition: definining this property disables charging + Definition: defining this property disables charging This charger is a sub-node of one of the 8941 PMIC blocks, and is specified as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt new file mode 100644 index 000000000..b74e4d478 --- /dev/null +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -0,0 +1,48 @@ +DT bindings for the Renesas R-Car System Controller + +== System Controller Node == + +The R-Car System Controller provides power management for the CPU cores and +various coprocessors. + +Required properties: + - compatible: Must contain exactly one of the following: + - "renesas,r8a7779-sysc" (R-Car H1) + - "renesas,r8a7790-sysc" (R-Car H2) + - "renesas,r8a7791-sysc" (R-Car M2-W) + - "renesas,r8a7792-sysc" (R-Car V2H) + - "renesas,r8a7793-sysc" (R-Car M2-N) + - "renesas,r8a7794-sysc" (R-Car E2) + - "renesas,r8a7795-sysc" (R-Car H3) + - reg: Address start and address range for the device. + - #power-domain-cells: Must be 1. + + +Example: + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a7791-sysc"; + reg = <0 0xe6180000 0 0x0200>; + #power-domain-cells = <1>; + }; + + +== PM Domain Consumers == + +Devices residing in a power area must refer to that power area, as documented +by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + +Required properties: + - power-domains: A phandle and symbolic PM domain specifier, as defined in + . + + +Example: + + L2_CA15: cache-controller@0 { + compatible = "cache"; + power-domains = <&sysc R8A7791_PD_CA15_SCU>; + cache-unified; + cache-level = <2>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt new file mode 100644 index 000000000..d4eab9227 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt @@ -0,0 +1,36 @@ +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a pm_power_off handler. If the optional properties 'input' is +not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the pm_power_off is called, the gpio is configured as an output, +and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the pm_power_off function is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/gpio-restart.txt b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt new file mode 100644 index 000000000..af3701bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index c84fb4726..d23dc002a 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -37,8 +37,10 @@ Required properties: - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains - "rockchip,rk3399-io-voltage-domain" for rk3399 - "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains -- rockchip,grf: phandle to the syscon managing the "general register files" +Deprecated properties: +- rockchip,grf: phandle to the syscon managing the "general register files" + Systems should move the io-domains to a sub-node of the grf simple-mfd. You specify supplies using the standard regulator bindings by including a phandle the relevant regulator. All specified supplies must be able diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt index f80ea2fe2..c2c68fcc1 100644 --- a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -32,6 +32,13 @@ Optional properties: Enhanced transient response (ETR) will affect the configuration of CKADV. +-junction-warn-millicelsius: u32, junction warning temperature threshold + in millicelsius. If die temperature crosses this level then + device generates the warning interrupts. + +Please note that thermal functionality is only supported on MAX77621. The +supported threshold warning temperature for MAX77621 are 120 degC and 140 degC. + Example: max8973@1b { diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index 725393c8a..998728196 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -1,5 +1,12 @@ * palmas regulator IP block devicetree bindings +The tps659038 for the AM57x class have OTP spins that +have different part numbers but the same functionality. There +is not a need to add the OTP spins to the palmas driver. The +spin devices should use the tps659038 as it's compatible value. +This is the list of those devices: +tps659037 + Required properties: - compatible : Should be from the list ti,twl6035-pmic @@ -8,6 +15,7 @@ Required properties: ti,tps65913-pmic ti,tps65914-pmic ti,tps65917-pmic + ti,tps659038-pmic and also the generic series names ti,palmas-pmic - interrupt-parent : The parent interrupt controller which is palmas. diff --git a/Documentation/devicetree/bindings/regulator/pv88080.txt b/Documentation/devicetree/bindings/regulator/pv88080.txt new file mode 100644 index 000000000..38a614210 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88080.txt @@ -0,0 +1,49 @@ +* Powerventure Semiconductor PV88080 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88080". +- reg: I2C slave address, usually 0x49. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, BUCK2, and BUCK3. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88080@49 { + compatible = "pvs,pv88080"; + reg = <0x49>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = < 220000>; + regulator-max-microamp = <7040000>; + }; + + BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + + BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2193750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index d00bfd862..46c6f3ed1 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -7,6 +7,7 @@ Qualcomm SPMI Regulators "qcom,pm8841-regulators" "qcom,pm8916-regulators" "qcom,pm8941-regulators" + "qcom,pm8994-regulators" - interrupts: Usage: optional @@ -68,6 +69,37 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vdd_s9-supply: +- vdd_s10-supply: +- vdd_s11-supply: +- vdd_s12-supply: +- vdd_l1-supply: +- vdd_l2_l26_l28-supply: +- vdd_l3_l11-supply: +- vdd_l4_l27_l31-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l32-supply: +- vdd_l8_l16_l30-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l14_l15-supply: +- vdd_l17_l29-supply: +- vdd_l20_l21-supply: +- vdd_l25-supply: +- vdd_lvs_1_2-supply: + Usage: optional (pm8994 only) + Value type: + Definition: Reference to regulator supplying the input pin, as + described in the data sheet. + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each @@ -85,6 +117,11 @@ pm8941: l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, mvs1, mvs2 +pm8994: + s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, + l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, + l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt - with additional custom properties described below: diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt index b3c8ca672..1c4bfe786 100644 --- a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -94,6 +94,28 @@ Following are additional properties: This is applicable if suspend state FPS source is selected as FPS0, FPS1 or FPS2. +- maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be + configured to the device. + The platform may have different ramp + rate than advertised ramp rate if it has + design variation from Maxim's + recommended. On this case, platform + specific ramp rate is used for ramp time + calculation and this property is used + for device register configurations. + The measured ramp rate of platform is + provided by the regulator-ramp-delay + as described in . + Maxim Max77620 supports following ramp + delay: + SD: 13.75mV/us, 27.5mV/us, 55mV/us + LDOs: 5mV/us, 100mV/us + +Note: If the measured ramp delay is same as advertised ramp delay then it is not +required to provide the ramp delay with property "maxim,ramp-rate-setting". The +ramp rate can be provided by the regulator-ramp-delay which will be used for +ramp time calculation for voltage change as well as for device configuration. Example: -------- diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index c58db75f9..c3f6546eb 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -14,8 +14,8 @@ Required Properties: - "setup-address" - contains setup register address of ABB module (ti,abb-v3) - "int-address" - contains address of interrupt register for ABB module (also see Optional properties) -- #address-cell: should be 0 -- #size-cell: should be 0 +- #address-cells: should be 0 +- #size-cells: should be 0 - clocks: should point to the clock node used by ABB module - ti,settling-time: Settling time in uSecs from SoC documentation for ABB module to settle down(target time for SR2_WTCNT_VALUE). @@ -69,7 +69,7 @@ Example #1: Simplest configuration (no efuse data, hard coded ABB table): abb_x: regulator-abb-x { compatible = "ti,abb-v1"; regulator-name = "abb_x"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x483072f0 0x8>, <0x48306818 0x4>; reg-names = "base-address", "int-address"; @@ -89,7 +89,7 @@ Example #2: Efuse bits contain ABB mode setting (no LDO override capability) abb_y: regulator-abb-y { compatible = "ti,abb-v2"; regulator-name = "abb_y"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; reg-names = "base-address", "int-address", "efuse-address"; @@ -110,7 +110,7 @@ Example #3: Efuse bits contain ABB mode setting and LDO override capability abb_z: regulator-abb-z { compatible = "ti,abb-v2"; regulator-name = "abb_z"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, <0x4a002194 0x8>, <0x4ae0C314 0x4>; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 75b0c1669..74a91c4f8 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -57,6 +57,12 @@ For twl4030 regulators/LDOs Optional properties: - Any optional property defined in bindings/regulator/regulator.txt +For twl4030 regulators/LDOs: + - regulator-initial-mode: + - 0x08 - Sleep mode, the nominal output voltage is maintained with low power + consumption with low load current capability. + - 0x0e - Active mode, the regulator can deliver its nominal output voltage + with full-load current capability. Example: diff --git a/Documentation/devicetree/bindings/reset/oxnas,reset.txt b/Documentation/devicetree/bindings/reset/oxnas,reset.txt new file mode 100644 index 000000000..6f06db930 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/oxnas,reset.txt @@ -0,0 +1,58 @@ +Oxford Semiconductor OXNAS SoC Family RESET Controller +================================================ + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "oxsemi,ox810se-reset" +- #reset-cells: 1, see below + +Parent node should have the following properties : +- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + +For OX810SE, the indices are : + - 0 : ARM + - 1 : COPRO + - 2 : Reserved + - 3 : Reserved + - 4 : USBHS + - 5 : USBHSPHY + - 6 : MAC + - 7 : PCI + - 8 : DMA + - 9 : DPE + - 10 : DDR + - 11 : SATA + - 12 : SATA_LINK + - 13 : SATA_PHY + - 14 : Reserved + - 15 : NAND + - 16 : GPIO + - 17 : UART1 + - 18 : UART2 + - 19 : MISC + - 20 : I2S + - 21 : AHB_MON + - 22 : UART3 + - 23 : UART4 + - 24 : SGDMA + - 25 : Reserved + - 26 : Reserved + - 27 : Reserved + - 28 : Reserved + - 29 : Reserved + - 30 : Reserved + - 31 : BUS + +example: + +sys: sys-ctrl@000000 { + compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"; + reg = <0x000000 0x100000>; + + reset: reset-controller { + compatible = "oxsemi,ox810se-reset"; + #reset-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/rng/hisi-rng.txt b/Documentation/devicetree/bindings/rng/hisi-rng.txt new file mode 100644 index 000000000..d04d55a6c --- /dev/null +++ b/Documentation/devicetree/bindings/rng/hisi-rng.txt @@ -0,0 +1,12 @@ +Hisilicon Random Number Generator + +Required properties: +- compatible : Should be "hisilicon,hip04-rng" or "hisilicon,hip05-rng" +- reg : Offset and length of the register set of this block + +Example: + +rng@d1010000 { + compatible = "hisilicon,hip05-rng"; + reg = <0xd1010000 0x100>; +}; diff --git a/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt new file mode 100644 index 000000000..ba470c56c --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim-ds1302.txt @@ -0,0 +1,46 @@ +* Maxim/Dallas Semiconductor DS-1302 RTC + +Simple device which could be used to store date/time between reboots. + +The device uses the standard MicroWire half-duplex transfer timing. +Master output is set on low clock and sensed by the RTC on the rising +edge. Master input is set by the RTC on the trailing edge and is sensed +by the master on low clock. + +Required properties: + +- compatible : Should be "maxim,ds1302" + +Required SPI properties: + +- reg : Should be address of the device chip select within + the controller. + +- spi-max-frequency : DS-1302 has 500 kHz if powered at 2.2V, + and 2MHz if powered at 5V. + +- spi-3wire : The device has a shared signal IN/OUT line. + +- spi-lsb-first : DS-1302 requires least significant bit first + transfers. + +- spi-cs-high: DS-1302 has active high chip select line. This is + required unless inverted in hardware. + +Example: + +spi@901c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "icpdas,lp8841-spi-rtc"; + reg = <0x901c 0x1>; + + rtc@0 { + compatible = "maxim,ds1302"; + reg = <0>; + spi-max-frequency = <500000>; + spi-3wire; + spi-lsb-first; + spi-cs-high; + }; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-palmas.txt b/Documentation/devicetree/bindings/rtc/rtc-palmas.txt index adbccc0a5..eb1c7fdeb 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-palmas.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-palmas.txt @@ -15,9 +15,9 @@ Optional properties: battery is chargeable or not. If charging battery then driver can enable the charging. - ti,backup-battery-charge-high-current: Enable high current charging in - backup battery. Device supports the < 100mA and > 100mA charging. - The high current will be > 100mA. Absence of this property will - charge battery to lower current i.e. < 100mA. + backup battery. Device supports the < 100uA and > 100uA charging. + The high current will be > 100uA. Absence of this property will + charge battery to lower current i.e. < 100uA. Example: palmas: tps65913@58 { diff --git a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt index 0cda19ad4..968ac8202 100644 --- a/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sa1100-rtc.txt @@ -13,5 +13,5 @@ Example: compatible = "mrvl,mmp-rtc"; reg = <0xd4010000 0x1000>; interrupts = <5>, <6>; - interrupt-name = "rtc 1Hz", "rtc alarm"; + interrupt-names = "rtc 1Hz", "rtc alarm"; }; diff --git a/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt new file mode 100644 index 000000000..128cc6aed --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt @@ -0,0 +1,19 @@ +ARM MPS2 UART + +Required properties: +- compatible : Should be "arm,mps2-uart" +- reg : Address and length of the register set +- interrupts : Reference to the UART RX, TX and overrun interrupts + +Required clocking property: +- clocks : The input clock of the UART + + +Examples: + +uart0: serial@40004000 { + compatible = "arm,mps2-uart"; + reg = <0x40004000 0x1000>; + interrupts = <0 1 12>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index ed94c217c..1e82802d8 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -6,7 +6,7 @@ Required properties: - interrupts : Should contain uart interrupt Optional properties: -- fsl,uart-has-rtscts : Indicate the uart has rts and cts +- uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. @@ -24,6 +24,6 @@ uart1: serial@73fbc000 { compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fbc000 0x4000>; interrupts = <31>; - fsl,uart-has-rtscts; + uart-has-rtscts; fsl,dte-mode; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt index 7c408c87e..5c96d4189 100644 --- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt @@ -1,8 +1,10 @@ * Freescale MXS Application UART (AUART) -Required properties: -- compatible : Should be "fsl,-auart". The supported SoCs include - imx23 and imx28. +Required properties for all SoCs: +- compatible : Should be one of fallowing variants: + "fsl,imx23-auart" - Freescale i.MX23 + "fsl,imx28-auart" - Freescale i.MX28 + "alphascale,asm9260-auart" - Alphascale ASM9260 - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers - dmas: DMA specifier, consisting of a phandle to DMA controller node @@ -10,8 +12,14 @@ Required properties: Refer to dma.txt and fsl-mxs-dma.txt for details. - dma-names: "rx" for RX channel, "tx" for TX channel. +Required properties for "alphascale,asm9260-auart": +- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt +- clock-names : should be set to + "mod" - source for tick counter. + "ahb" - ahb gate. + Optional properties: -- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines +- uart-has-rtscts : Indicate the UART has RTS and CTS lines for hardware flow control, it also means you enable the DMA support for this UART. - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD diff --git a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt new file mode 100644 index 000000000..7a34345d0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt @@ -0,0 +1,29 @@ +* Microchip Universal Asynchronous Receiver Transmitter (UART) + +Required properties: +- compatible: Should be "microchip,pic32mzda-uart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the UART peripheral. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +Optional properties: +- cts-gpios: CTS pin for UART + +Example: + uart1: serial@1f822000 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822000 0x50>; + interrupts = <112 IRQ_TYPE_LEVEL_HIGH>, + <113 IRQ_TYPE_LEVEL_HIGH>, + <114 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rootclk PB2CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 + &pinctrl_uart1_cts + &pinctrl_uart1_rts>; + cts-gpios = <&gpio1 15 0>; + }; diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt new file mode 100644 index 000000000..6087defd9 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt @@ -0,0 +1,13 @@ +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700) + +Required properties: +- compatible: "marvell,armada-3700-uart" +- reg: offset and length of the register set for the device. +- interrupts: device interrupt + +Example: + serial@12000 { + compatible = "marvell,armada-3700-uart"; + reg = <0x12000 0x400>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt new file mode 100644 index 000000000..fd970f76a --- /dev/null +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -0,0 +1,57 @@ +Generic Serial DT Bindings + +This document lists a set of generic properties for describing UARTs in a +device tree. Whether these properties apply to a particular device depends on +the DT bindings for the actual device. + +Optional properties: + - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's CTS line. + - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DCD line. + - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DSR line. + - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's DTR line. + - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's RNG line. + - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be + used as the UART's RTS line. + + - uart-has-rtscts: The presence of this property indicates that the + UART has dedicated lines for RTS/CTS hardware flow control, and that + they are available for use (wired and enabled by pinmux configuration). + This depends on both the UART hardware and the board wiring. + Note that this property is mutually-exclusive with "cts-gpios" and + "rts-gpios" above. + + +Examples: + + uart1: serial@48022000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + reg = <0x48022000 0x2000>; + interrupts = <73>; + dmas = <&edma 28 0>, <&edma 29 0>; + dma-names = "tx", "rx"; + dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; + cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + + scifa4: serial@e6c80000 { + compatible = "renesas,scifa-sh73a0", "renesas,scifa"; + reg = <0xe6c80000 0x100>; + interrupts = ; + clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>; + clock-names = "fck"; + power-domains = <&pd_a3sp>; + uart-has-rtscts; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt index 67e2a0aeb..1e48bbbee 100644 --- a/Documentation/devicetree/bindings/serial/sirf-uart.txt +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -9,9 +9,9 @@ Required properties: - clocks : Should contain uart clock number Optional properties: -- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware -- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true -- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true +- uart-has-rtscts: we have hardware flow controller pins in hardware +- rts-gpios: RTS pin for USP-based UART if uart-has-rtscts is true +- cts-gpios: CTS pin for USP-based UART if uart-has-rtscts is true Example: @@ -28,7 +28,7 @@ On the board-specific dts, we can put rts-gpios and cts-gpios like usp@b0090000 { compatible = "sirf,prima2-usp-uart"; - sirf,uart-has-rtscts; + uart-has-rtscts; rts-gpios = <&gpio 15 0>; cts-gpios = <&gpio 46 0>; }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt b/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt new file mode 100644 index 000000000..bdb782918 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt @@ -0,0 +1,21 @@ +MediaTek AUXADC +=============== + +The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found +in some Mediatek SoCs which among other things measures the temperatures +in the SoC. It can be used directly with register accesses, but it is also +used by thermal controller which reads the temperatures from the AUXADC +directly via its own bus interface. See +Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +for the Thermal Controller which holds a phandle to the AUXADC. + +Required properties: +- compatible: Must be "mediatek,mt8173-auxadc" +- reg: Address range of the AUXADC unit + +Example: + +auxadc: auxadc@11001000 { + compatible = "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt index ddeb5b6a5..107700d00 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -18,6 +18,7 @@ IP Pairing Required properties in pwrap device node. - compatible: + "mediatek,mt2701-pwrap" for MT2701/7623 SoCs "mediatek,mt8135-pwrap" for MT8135 SoCs "mediatek,mt8173-pwrap" for MT8173 SoCs - interrupts: IRQ for pwrap in SOC diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt new file mode 100644 index 000000000..013e71a2c --- /dev/null +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -0,0 +1,35 @@ +* Rockchip General Register Files (GRF) + +The general register file will be used to do static set by software, which +is composed of many registers for system control. + +From RK3368 SoCs, the GRF is divided into two sections, +- GRF, used for general non-secure system, +- PMUGRF, used for always on system + +Required Properties: + +- compatible: GRF should be one of the followings + - "rockchip,rk3066-grf", "syscon": for rk3066 + - "rockchip,rk3188-grf", "syscon": for rk3188 + - "rockchip,rk3228-grf", "syscon": for rk3228 + - "rockchip,rk3288-grf", "syscon": for rk3288 + - "rockchip,rk3368-grf", "syscon": for rk3368 + - "rockchip,rk3399-grf", "syscon": for rk3399 +- compatible: PMUGRF should be one of the followings + - "rockchip,rk3368-pmugrf", "syscon": for rk3368 + - "rockchip,rk3399-pmugrf", "syscon": for rk3399 +- reg: physical base address of the controller and length of memory mapped + region. + +Example: GRF and PMUGRF of RK3399 SoCs + + pmugrf: syscon@ff320000 { + compatible = "rockchip,rk3399-pmugrf", "syscon"; + reg = <0x0 0xff320000 0x0 0x1000>; + }; + + grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon"; + reg = <0x0 0xff770000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 13dc6a3fd..f909ce06a 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -7,6 +7,7 @@ Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3368-power-controller" - for RK3368 SoCs. + "rockchip,rk3399-power-controller" - for RK3399 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. Should be 1 for multiple PM domains. - #address-cells: Should be 1. @@ -16,8 +17,18 @@ Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. + "include/dt-bindings/power/rk3399-power.h" - for RK3399 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain switches state. +- pm_qos (optional): phandles to qos blocks which need to be saved and restored + while power domain switches state. + +Qos Example: + + qos_gpu: qos_gpu@ffaf0000 { + compatible ="syscon"; + reg = <0x0 0xffaf0000 0x0 0x20>; + }; Example: @@ -30,6 +41,7 @@ Example: pd_gpu { reg = ; clocks = <&cru ACLK_GPU>; + pm_qos = <&qos_gpu>; }; }; @@ -45,12 +57,41 @@ Example: }; }; +Example 2: + power: power-controller { + compatible = "rockchip,rk3399-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_vio { + #address-cells = <1>; + #size-cells = <0>; + reg = ; + + pd_vo { + #address-cells = <1>; + #size-cells = <0>; + reg = ; + + pd_vopb { + reg = ; + }; + + pd_vopl { + reg = ; + }; + }; + }; + }; + Node of a device using power domains must have a power-domains property, containing a phandle to the power device node and an index specifying which power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. + "include/dt-bindings/power/rk3399-power.h" - for rk3399 type power domain. Example of the node using power domain: @@ -65,3 +106,9 @@ Example of the node using power domain: power-domains = <&power RK3368_PD_GPU_1>; /* ... */ }; + + node { + /* ... */ + power-domains = <&power RK3399_PD_VOPB>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt index d1ce21a49..64c66a564 100644 --- a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -42,7 +42,7 @@ Required properties: - queue-pools : child node classifying the queue ranges into pools. Queue ranges are grouped into 3 type of pools: - qpend : pool of qpend(interruptible) queues - - general-purpose : pool of general queues, primarly used + - general-purpose : pool of general queues, primarily used as free descriptor queues or the transmit DMA queues. - accumulator : pool of queues on PDSP accumulator channel @@ -50,7 +50,7 @@ Required properties: -- qrange : number of queues to use per queue range, specified as <"base queue #" "# of queues">. -- interrupts : Optional property to specify the interrupt mapping - for interruptible queues. The driver additionaly sets + for interruptible queues. The driver additionally sets the interrupt affinity hint based on the cpu mask. -- qalloc-by-id : Optional property to specify that the queues in this range can only be allocated by queue id. @@ -80,7 +80,7 @@ Required properties: latency : time to delay the interrupt, specified in microseconds. -- multi-queue : Optional property to specify that the channel has to - monitor upto 32 queues starting at the base queue #. + monitor up to 32 queues starting at the base queue #. - descriptor-regions : child node describing the memory regions for keystone navigator packet DMA descriptors. The memory for descriptors will be allocated by the driver. diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt new file mode 100644 index 000000000..55b53e1fd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -0,0 +1,51 @@ +Texas Instruments DaVinci McBSP module +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +This binding describes the "Multi-channel Buffered Serial Port" (McBSP) +audio interface found in some TI DaVinci processors like the OMAP-L138 or AM180x. + + +Required properties: +~~~~~~~~~~~~~~~~~~~~ +- compatible : + "ti,da850-mcbsp" : for DA850, AM180x and OPAM-L138 platforms + +- reg : physical base address and length of the controller memory mapped + region(s). +- reg-names : Should contain: + * "mpu" for the main registers (required). + * "dat" for the data FIFO (optional). + +- dmas: three element list of DMA controller phandles, DMA request line and + TC channel ordered triplets. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ +- interrupts : Interrupt numbers for McBSP +- interrupt-names : Known interrupt names are "rx" and "tx" + +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + +Example (AM1808): +~~~~~~~~~~~~~~~~~ + +mcbsp0: mcbsp@1d10000 { + compatible = "ti,da850-mcbsp"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp0_pins>; + + reg = <0x00110000 0x1000>, + <0x00310000 0x1000>; + reg-names = "mpu", "dat"; + interrupts = <97 98>; + interrupts-names = "rx", "tx"; + dmas = <&edma0 3 1 + &edma0 2 1>; + dma-names = "tx", "rx"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 044e5d76e..740b467ad 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,8 +7,8 @@ codec/DSP interfaces. Required properties: - - compatible : Compatible list, contains "fsl,vf610-sai" or - "fsl,imx6sx-sai". + - compatible : Compatible list, contains "fsl,vf610-sai", + "fsl,imx6sx-sai" or "fsl,imx6ul-sai" - reg : Offset and length of the register set for the device. @@ -48,6 +48,11 @@ Required properties: receive data by following their own bit clocks and frame sync clocks separately. +Optional properties (for mx6ul): + + - fsl,sai-mclk-direction-output: This is a boolean property. If present, + indicates that SAI will output the SAI MCLK clock. + Note: - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the default synchronous mode (sync Rx with Tx) will be used, which means both diff --git a/Documentation/devicetree/bindings/sound/max98371.txt b/Documentation/devicetree/bindings/sound/max98371.txt new file mode 100644 index 000000000..6c285235e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98371.txt @@ -0,0 +1,17 @@ +max98371 codec + +This device supports I2C mode only. + +Required properties: + +- compatible : "maxim,max98371" +- reg : The chip select number on the I2C bus + +Example: + +&i2c { + max98371: max98371@0x31 { + compatible = "maxim,max98371"; + reg = <0x31>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt index f205ce9e3..ac28cdb49 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt @@ -1,15 +1,16 @@ -MT8173 with RT5650 RT5676 CODECS +MT8173 with RT5650 RT5676 CODECS and HDMI via I2S Required properties: - compatible : "mediatek,mt8173-rt5650-rt5676" - mediatek,audio-codec: the phandles of rt5650 and rt5676 codecs + and of the hdmi encoder node - mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-rt5650-rt5676"; - mediatek,audio-codec = <&rt5650 &rt5676>; + mediatek,audio-codec = <&rt5650 &rt5676 &hdmi0>; mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt index fe5a5ef17..5bfa6b605 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt @@ -5,11 +5,21 @@ Required properties: - mediatek,audio-codec: the phandles of rt5650 codecs - mediatek,platform: the phandle of MT8173 ASoC platform +Optional subnodes: +- codec-capture : the subnode of rt5650 codec capture +Required codec-capture subnode properties: +- sound-dai: audio codec dai name on capture path + <&rt5650 0> : Default setting. Connect rt5650 I2S1 for capture. (dai_name = rt5645-aif1) + <&rt5650 1> : Connect rt5650 I2S2 for capture. (dai_name = rt5645-aif2) + Example: sound { compatible = "mediatek,mt8173-rt5650"; mediatek,audio-codec = <&rt5650>; mediatek,platform = <&afe>; + codec-capture { + sound-dai = <&rt5650 1>; + }; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt index 275c6ea35..44d27456e 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -15,7 +15,7 @@ Required properties: Example: -hda@0,70030000 { +hda@70030000 { compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda"; reg = <0x0 0x70030000 0x0 0x10000>; interrupts = ; diff --git a/Documentation/devicetree/bindings/sound/pcm5102a.txt b/Documentation/devicetree/bindings/sound/pcm5102a.txt new file mode 100644 index 000000000..c63ab0b6e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm5102a.txt @@ -0,0 +1,13 @@ +PCM5102a audio CODECs + +These devices does not use I2C or SPI. + +Required properties: + + - compatible : set as "ti,pcm5102a" + +Examples: + + pcm5102a: pcm5102a { + compatible = "ti,pcm5102a"; + }; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 028fa1c82..4d9a83d9a 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -37,17 +37,18 @@ Required properties: - dai-name: DAI name that describes the IP. + - IP mode: IP working mode depending on associated codec. + "HDMI" connected to HDMI codec and support IEC HDMI formats (player only). + "SPDIF" connected to SPDIF codec and support SPDIF formats (player only). + "PCM" PCM standard mode for I2S or TDM bus. + "TDM" TDM mode for TDM bus. + Required properties ("st,sti-uni-player" compatibility only): - clocks: CPU_DAI IP clock source, listed in the same order than the CPU_DAI properties. - uniperiph-id: internal SOC IP instance ID. - - IP mode: IP working mode depending on associated codec. - "HDMI" connected to HDMI codec IP and IEC HDMI formats. - "SPDIF"connected to SPDIF codec and support SPDIF formats. - "PCM" PCM standard mode for I2S or TDM bus. - Optional properties: - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for external codecs connection. @@ -56,6 +57,22 @@ Optional properties: Example: + sti_uni_player1: sti-uni-player@1 { + compatible = "st,sti-uni-player"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_1>; + reg = <0x8D81000 0x158>; + interrupts = ; + dmas = <&fdma0 3 0 1>; + st,dai-name = "Uni Player #1 (I2S)"; + dma-names = "tx"; + st,uniperiph-id = <1>; + st,version = <5>; + st,mode = "TDM"; + }; + sti_uni_player2: sti-uni-player@2 { compatible = "st,sti-uni-player"; status = "okay"; @@ -65,7 +82,7 @@ Example: reg = <0x8D82000 0x158>; interrupts = ; dmas = <&fdma0 4 0 1>; - dai-name = "Uni Player #1 (DAC)"; + dai-name = "Uni Player #2 (DAC)"; dma-names = "tx"; uniperiph-id = <2>; version = <5>; @@ -82,7 +99,7 @@ Example: interrupts = ; dmas = <&fdma0 7 0 1>; dma-names = "tx"; - dai-name = "Uni Player #1 (PIO)"; + dai-name = "Uni Player #3 (SPDIF)"; uniperiph-id = <3>; version = <5>; mode = "SPDIF"; @@ -99,6 +116,7 @@ Example: dma-names = "rx"; dai-name = "Uni Reader #1 (HDMI RX)"; version = <3>; + st,mode = "PCM"; }; 2) sti-sas-codec: internal audio codec IPs driver @@ -152,4 +170,20 @@ Example of audio card declaration: sound-dai = <&sti_sasg_codec 0>; }; }; + simple-audio-card,dai-link@2 { + /* TDM playback */ + format = "left_j"; + frame-inversion = <1>; + cpu { + sound-dai = <&sti_uni_player1>; + dai-tdm-slot-num = <16>; + dai-tdm-slot-width = <16>; + dai-tdm-slot-tx-mask = + <1 1 1 1 0 0 0 0 0 0 1 1 0 0 1 1>; + }; + + codec { + sound-dai = <&sti_sasg_codec 3>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/sound/tas571x.txt b/Documentation/devicetree/bindings/sound/tas571x.txt index 0ac31d8d5..b4959f10b 100644 --- a/Documentation/devicetree/bindings/sound/tas571x.txt +++ b/Documentation/devicetree/bindings/sound/tas571x.txt @@ -1,4 +1,4 @@ -Texas Instruments TAS5711/TAS5717/TAS5719 stereo power amplifiers +Texas Instruments TAS5711/TAS5717/TAS5719/TAS5721 stereo power amplifiers The codec is controlled through an I2C interface. It also has two other signals that can be wired up to GPIOs: reset (strongly recommended), and @@ -6,7 +6,11 @@ powerdown (optional). Required properties: -- compatible: "ti,tas5711", "ti,tas5717", or "ti,tas5719" +- compatible: should be one of the following: + - "ti,tas5711", + - "ti,tas5717", + - "ti,tas5719", + - "ti,tas5721" - reg: The I2C address of the device - #sound-dai-cells: must be equal to 0 @@ -25,6 +29,8 @@ Optional properties: - PVDD_B-supply: regulator phandle for the PVDD_B supply (5711) - PVDD_C-supply: regulator phandle for the PVDD_C supply (5711) - PVDD_D-supply: regulator phandle for the PVDD_D supply (5711) +- DRVDD-supply: regulator phandle for the DRVDD supply (5721) +- PVDD-supply: regulator phandle for the PVDD supply (5721) Example: diff --git a/Documentation/devicetree/bindings/sound/tas5720.txt b/Documentation/devicetree/bindings/sound/tas5720.txt new file mode 100644 index 000000000..806ea7381 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas5720.txt @@ -0,0 +1,25 @@ +Texas Instruments TAS5720 Mono Audio amplifier + +The TAS5720 serial control bus communicates through the I2C protocol only. The +serial bus is also used for periodic codec fault checking/reporting during +audio playback. For more product information please see the links below: + +http://www.ti.com/product/TAS5720L +http://www.ti.com/product/TAS5720M + +Required properties: + +- compatible : "ti,tas5720" +- reg : I2C slave address +- dvdd-supply : phandle to a 3.3-V supply for the digital circuitry +- pvdd-supply : phandle to a supply used for the Class-D amp and the analog + +Example: + +tas5720: tas5720@6c { + status = "okay"; + compatible = "ti,tas5720"; + reg = <0x6c>; + dvdd-supply = <&vdd_3v3_reg>; + pvdd-supply = <&_supply_reg>; +}; diff --git a/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt new file mode 100644 index 000000000..79de379f4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt @@ -0,0 +1,34 @@ +Microchip PIC32 SPI Master controller + +Required properties: +- compatible: Should be "microchip,pic32mzda-spi". +- reg: Address and length of register space for the device. +- interrupts: Should contain all three spi interrupts in sequence + of , , . +- interrupt-names: Should be "fault", "rx", "tx" in order. +- clocks: Phandle of the clock generating SPI clock on the bus. +- clock-names: Should be "mck0". +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- dmas: Two or more DMA channel specifiers following the convention outlined + in Documentation/devicetree/bindings/dma/dma.txt +- dma-names: Names for the dma channels. There must be at least one channel + named "spi-tx" for transmit and named "spi-rx" for receive. + +Example: + +spi1: spi@1f821000 { + compatible = "microchip,pic32mzda-spi"; + reg = <0x1f821000 0x200>; + interrupts = <109 IRQ_TYPE_LEVEL_HIGH>, + <110 IRQ_TYPE_LEVEL_HIGH>, + <111 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fault", "rx", "tx"; + clocks = <&PBCLK2>; + clock-names = "mck0"; + cs-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + dmas = <&dma 134>, <&dma 135>; + dma-names = "spi-rx", "spi-tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index fa77f874e..ff5893d27 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -1,7 +1,10 @@ ARM Freescale DSPI controller Required properties: -- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", "fsl,ls2085a-dspi" +- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", + "fsl,ls2085a-dspi" + or + "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. @@ -13,8 +16,7 @@ Required properties: Optional property: - big-endian: If present the dspi device's registers are implemented - in big endian mode, otherwise in native mode(same with CPU), for more - detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + in big endian mode. Optional SPI slave node properties: - fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip diff --git a/Documentation/devicetree/bindings/spi/sqi-pic32.txt b/Documentation/devicetree/bindings/spi/sqi-pic32.txt new file mode 100644 index 000000000..c82d021bc --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sqi-pic32.txt @@ -0,0 +1,18 @@ +Microchip PIC32 Quad SPI controller +----------------------------------- +Required properties: +- compatible: Should be "microchip,pic32mzda-sqi". +- reg: Address and length of SQI controller register space. +- interrupts: Should contain SQI interrupt. +- clocks: Should contain phandle of two clocks in sequence, one that drives + clock on SPI bus and other that drives SQI controller. +- clock-names: Should be "spi_ck" and "reg_ck" in order. + +Example: + sqi1: spi@1f8e2000 { + compatible = "microchip,pic32mzda-sqi"; + reg = <0x1f8e2000 0x200>; + clocks = <&rootclk REF2CLK>, <&rootclk PB5CLK>; + clock-names = "spi_ck", "reg_ck"; + interrupts = <169 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index cc8304aa6..50b14f6b5 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -19,6 +19,13 @@ Optional properties: - syscon-chipselects: Handle to system control region contains QSPI chipselect register and offset of that register. +NOTE: TI QSPI controller requires different pinmux and IODelay +paramaters for Mode-0 and Mode-3 operations, which needs to be set up by +the bootloader (U-Boot). Default configuration only supports Mode-0 +operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be +specified in the slave nodes of TI QSPI controller without appropriate +modification to bootloader. + Example: For am4372: diff --git a/Documentation/devicetree/bindings/sram/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index 227e3a341..add48f090 100644 --- a/Documentation/devicetree/bindings/sram/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt @@ -51,7 +51,7 @@ sram: sram@5c000000 { compatible = "mmio-sram"; reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ - #adress-cells = <1>; + #address-cells = <1>; #size-cells = <1>; ranges = <0 0x5c000000 0x40000>; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt deleted file mode 100644 index 555fb117d..000000000 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ /dev/null @@ -1,47 +0,0 @@ -* Freescale MXS LRADC device driver - -Required properties: -- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" - for i.MX28 SoC -- reg: Address and length of the register set for the device -- interrupts: Should contain the LRADC interrupts - -Optional properties: -- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen - to LRADC. Valid value is either 4 or 5. If this - property is not present, then the touchscreen is - disabled. 5 wires is valid for i.MX28 SoC only. -- fsl,ave-ctrl: number of samples per direction to calculate an average value. - Allowed value is 1 ... 32, default is 4 -- fsl,ave-delay: delay between consecutive samples. Allowed value is - 2 ... 2048. It is used if 'fsl,ave-ctrl' > 1, counts at - 2 kHz and its default is 2 (= 1 ms) -- fsl,settling: delay between plate switch to next sample. Allowed value is - 1 ... 2047. It counts at 2 kHz and its default is - 10 (= 5 ms) - -Example for i.MX23 SoC: - - lradc@80050000 { - compatible = "fsl,imx23-lradc"; - reg = <0x80050000 0x2000>; - interrupts = <36 37 38 39 40 41 42 43 44>; - status = "okay"; - fsl,lradc-touchscreen-wires = <4>; - fsl,ave-ctrl = <4>; - fsl,ave-delay = <2>; - fsl,settling = <10>; - }; - -Example for i.MX28 SoC: - - lradc@80050000 { - compatible = "fsl,imx28-lradc"; - reg = <0x80050000 0x2000>; - interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; - status = "okay"; - fsl,lradc-touchscreen-wires = <5>; - fsl,ave-ctrl = <4>; - fsl,ave-delay = <2>; - fsl,settling = <10>; - }; diff --git a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt new file mode 100644 index 000000000..edebfa0a9 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt @@ -0,0 +1,67 @@ +Tegra124 SOCTHERM thermal management system + +The SOCTHERM IP block contains thermal sensors, support for polled +or interrupt-based thermal monitoring, CPU and GPU throttling based +on temperature trip points, and handling external overcurrent +notifications. It is also used to manage emergency shutdown in an +overheating situation. + +Required properties : +- compatible : For Tegra124, must contain "nvidia,tegra124-soctherm". + For Tegra132, must contain "nvidia,tegra132-soctherm". + For Tegra210, must contain "nvidia,tegra210-soctherm". +- reg : Should contain 1 entry: + - SOCTHERM register set +- interrupts : Defines the interrupt used by SOCTHERM +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - tsensor + - soctherm +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - soctherm +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description + of this property. See for a + list of valid values when referring to thermal sensors. + +Note: +- the "critical" type trip points will be set to SOC_THERM hardware as the +shut down temperature. Once the temperature of this thermal zone is higher +than it, the system will be shutdown or reset by hardware. + +Example : + + soctherm@700e2000 { + compatible = "nvidia,tegra124-soctherm"; + reg = <0x0 0x700e2000 0x0 0x1000>; + interrupts = ; + clocks = <&tegra_car TEGRA124_CLK_TSENSOR>, + <&tegra_car TEGRA124_CLK_SOC_THERM>; + clock-names = "tsensor", "soctherm"; + resets = <&tegra_car 78>; + reset-names = "soctherm"; + + #thermal-sensor-cells = <1>; + }; + +Example: referring to thermal sensors : + + thermal-zones { + cpu { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = + <&soctherm TEGRA124_SOCTHERM_SENSOR_CPU>; + + trips { + cpu_shutdown_trip: shutdown-trip { + temperature = <102500>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index e5ee3f159..a8e52c8cc 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -11,7 +11,6 @@ Required properties: - "renesas,thermal-r8a7791" (R-Car M2-W) - "renesas,thermal-r8a7792" (R-Car V2H) - "renesas,thermal-r8a7793" (R-Car M2-N) - - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". diff --git a/Documentation/devicetree/bindings/thermal/tango-thermal.txt b/Documentation/devicetree/bindings/thermal/tango-thermal.txt new file mode 100644 index 000000000..212198d4b --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/tango-thermal.txt @@ -0,0 +1,17 @@ +* Tango Thermal + +The SMP8758 SoC includes 3 instances of this temperature sensor +(in the CPU, video decoder, and PCIe controller). + +Required properties: +- #thermal-sensor-cells: Should be 0 (see thermal.txt) +- compatible: "sigma,smp8758-thermal" +- reg: Address range of the thermal registers + +Example: + + cpu_temp: thermal@920100 { + #thermal-sensor-cells = <0>; + compatible = "sigma,smp8758-thermal"; + reg = <0x920100 12>; + }; diff --git a/Documentation/devicetree/bindings/thermal/tegra-soctherm.txt b/Documentation/devicetree/bindings/thermal/tegra-soctherm.txt deleted file mode 100644 index 6b68cd150..000000000 --- a/Documentation/devicetree/bindings/thermal/tegra-soctherm.txt +++ /dev/null @@ -1,55 +0,0 @@ -Tegra124 SOCTHERM thermal management system - -The SOCTHERM IP block contains thermal sensors, support for polled -or interrupt-based thermal monitoring, CPU and GPU throttling based -on temperature trip points, and handling external overcurrent -notifications. It is also used to manage emergency shutdown in an -overheating situation. - -Required properties : -- compatible : For Tegra124, must contain "nvidia,tegra124-soctherm". - For Tegra132, must contain "nvidia,tegra132-soctherm". - For Tegra210, must contain "nvidia,tegra210-soctherm". -- reg : Should contain 1 entry: - - SOCTHERM register set -- interrupts : Defines the interrupt used by SOCTHERM -- clocks : Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names : Must include the following entries: - - tsensor - - soctherm -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include the following entries: - - soctherm -- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description - of this property. See for a - list of valid values when referring to thermal sensors. - - -Example : - - soctherm@0,700e2000 { - compatible = "nvidia,tegra124-soctherm"; - reg = <0x0 0x700e2000 0x0 0x1000>; - interrupts = ; - clocks = <&tegra_car TEGRA124_CLK_TSENSOR>, - <&tegra_car TEGRA124_CLK_SOC_THERM>; - clock-names = "tsensor", "soctherm"; - resets = <&tegra_car 78>; - reset-names = "soctherm"; - - #thermal-sensor-cells = <1>; - }; - -Example: referring to thermal sensors : - - thermal-zones { - cpu { - polling-delay-passive = <1000>; - polling-delay = <1000>; - - thermal-sensors = - <&soctherm TEGRA124_SOCTHERM_SENSOR_CPU>; - }; - }; diff --git a/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt b/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt new file mode 100644 index 000000000..d72355502 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/thermal-generic-adc.txt @@ -0,0 +1,89 @@ +General Purpose Analog To Digital Converter (ADC) based thermal sensor. + +On some of platforms, thermal sensor like thermistors are connected to +one of ADC channel and sensor resistance is read via voltage across the +sensor resistor. The voltage read across the sensor is mapped to +temperature using voltage-temperature lookup table. + +Required properties: +=================== +- compatible: Must be "generic-adc-thermal". +- temperature-lookup-table: Two dimensional array of Integer; lookup table + to map the relation between ADC value and + temperature. When ADC is read, the value is + looked up on the table to get the equivalent + temperature. + The first value of the each row of array is the + temperature in milliCelsius and second value of + the each row of array is the ADC read value. +- #thermal-sensor-cells: Should be 1. See ./thermal.txt for a description + of this property. + +Example : +#include + +i2c@7000c400 { + ads1015: ads1015@4a { + reg = <0x4a>; + compatible = "ads1015"; + sampling-frequency = <3300>; + #io-channel-cells = <1>; + }; +}; + +tboard_thermistor: thermal-sensor { + compatible = "generic-adc-thermal"; + #thermal-sensor-cells = <0>; + io-channels = <&ads1015 1>; + io-channel-names = "sensor-channel"; + temperature-lookup-table = < (-40000) 2578 + (-39000) 2577 + (-38000) 2576 + (-37000) 2575 + (-36000) 2574 + (-35000) 2573 + (-34000) 2572 + (-33000) 2571 + (-32000) 2569 + (-31000) 2568 + (-30000) 2567 + :::::::::: + 118000 254 + 119000 247 + 120000 240 + 121000 233 + 122000 226 + 123000 220 + 124000 214 + 125000 208>; +}; + +dummy_cool_dev: dummy-cool-dev { + compatible = "dummy-cooling-dev"; + #cooling-cells = <2>; /* min followed by max */ +}; + +thermal-zones { + Tboard { + polling-delay = <15000>; /* milliseconds */ + polling-delay-passive = <0>; /* milliseconds */ + thermal-sensors = <&tboard_thermistor>; + + trips { + therm_est_trip: therm_est_trip { + temperature = <40000>; + type = "active"; + hysteresis = <1000>; + }; + }; + + cooling-maps { + map0 { + trip = <&therm_est_trip>; + cooling-device = <&dummy_cool_dev THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <100>; + }; + + }; + }; +}; diff --git a/Documentation/devicetree/bindings/timer/arm,mps2-timer.txt b/Documentation/devicetree/bindings/timer/arm,mps2-timer.txt new file mode 100644 index 000000000..48f84d74e --- /dev/null +++ b/Documentation/devicetree/bindings/timer/arm,mps2-timer.txt @@ -0,0 +1,28 @@ +ARM MPS2 timer + +The MPS2 platform has simple general-purpose 32 bits timers. + +Required properties: +- compatible : Should be "arm,mps2-timer" +- reg : Address and length of the register set +- interrupts : Reference to the timer interrupt + +Required clocking property, have to be one of: +- clocks : The input clock of the timer +- clock-frequency : The rate in HZ in input of the ARM MPS2 timer + +Examples: + +timer1: mps2-timer@40000000 { + compatible = "arm,mps2-timer"; + reg = <0x40000000 0x1000>; + interrupts = <8>; + clocks = <&sysclk>; +}; + +timer2: mps2-timer@40001000 { + compatible = "arm,mps2-timer"; + reg = <0x40001000 0x1000>; + interrupts = <9>; + clock-frequency = <25000000>; +}; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt new file mode 100644 index 000000000..c8c03d700 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt @@ -0,0 +1,15 @@ +NPS Network Processor + +Required properties: + +- compatible : should be "ezchip,nps400-timer" + +Clocks required for compatible = "ezchip,nps400-timer": +- clocks : Must contain a single entry describing the clock input + +Example: + +timer { + compatible = "ezchip,nps400-timer"; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/timer/snps,arc-timer.txt b/Documentation/devicetree/bindings/timer/snps,arc-timer.txt new file mode 100644 index 000000000..4ef024630 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,arc-timer.txt @@ -0,0 +1,31 @@ +Synopsys ARC Local Timer with Interrupt Capabilities +- Found on all ARC CPUs (ARC700/ARCHS) +- Can be optionally programmed to interrupt on Limit +- Two idential copies TIMER0 and TIMER1 exist in ARC cores and historically + TIMER0 used as clockevent provider (true for all ARC cores) + TIMER1 used for clocksource (mandatory for ARC700, optional for ARC HS) + +Required properties: + +- compatible : should be "snps,arc-timer" +- interrupts : single Interrupt going into parent intc + (16 for ARCHS cores, 3 for ARC700 cores) +- clocks : phandle to the source clock + +Optional properties: + +- interrupt-parent : phandle to parent intc + +Example: + + timer0 { + compatible = "snps,arc-timer"; + interrupts = <3>; + interrupt-parent = <&core_intc>; + clocks = <&core_clk>; + }; + + timer1 { + compatible = "snps,arc-timer"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt b/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt new file mode 100644 index 000000000..b6cd1b392 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,archs-gfrc.txt @@ -0,0 +1,14 @@ +Synopsys ARC Free Running 64-bit Global Timer for ARC HS CPUs +- clocksource provider for SMP SoC + +Required properties: + +- compatible : should be "snps,archs-gfrc" +- clocks : phandle to the source clock + +Example: + + gfrc { + compatible = "snps,archs-gfrc"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt b/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt new file mode 100644 index 000000000..47bd7a702 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/snps,archs-rtc.txt @@ -0,0 +1,14 @@ +Synopsys ARC Free Running 64-bit Local Timer for ARC HS CPUs +- clocksource provider for UP SoC + +Required properties: + +- compatible : should be "snps,archs-rtc" +- clocks : phandle to the source clock + +Example: + + rtc { + compatible = "snps,arc-rtc"; + clocks = <&core_clk>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt deleted file mode 100644 index 6087defd9..000000000 --- a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt +++ /dev/null @@ -1,13 +0,0 @@ -* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700) - -Required properties: -- compatible: "marvell,armada-3700-uart" -- reg: offset and length of the register set for the device. -- interrupts: device interrupt - -Example: - serial@12000 { - compatible = "marvell,armada-3700-uart"; - reg = <0x12000 0x400>; - interrupts = <43>; - }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index fb2ad0ace..7d7ce089b 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -14,7 +14,6 @@ Optional properties: the second element is expected to be a handle to the USB3/SS PHY - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings - - tx-fifo-resize: determines if the FIFO *has* to be reallocated. - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. @@ -38,6 +37,8 @@ Optional properties: - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal to the PHY. + - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection + in PHY P3 power state. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold @@ -47,6 +48,8 @@ Optional properties: register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { @@ -54,5 +57,4 @@ dwc3@4a030000 { reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; - tx-fifo-resize; }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt new file mode 100644 index 000000000..d28295a3e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra xHCI controller +============================ + +The Tegra xHCI controller supports both USB2 and USB3 interfaces exposed by +the Tegra XUSB pad controller. + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb" + - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb" + - Tegra210: "nvidia,tegra210-xusb" +- reg: Must contain the base and length of the xHCI host registers, XUSB FPCI + registers and XUSB IPFS registers. +- reg-names: Must contain the following entries: + - "hcd" + - "fpci" + - "ipfs" +- interrupts: Must contain the xHCI host interrupt and the mailbox interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - xusb_host + - xusb_host_src + - xusb_falcon_src + - xusb_ss + - xusb_ss_src + - xusb_ss_div2 + - xusb_hs_src + - xusb_fs_src + - pll_u_480m + - clk_m + - pll_e +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - xusb_host + - xusb_ss + - xusb_src + Note that xusb_src is the shared reset for xusb_{ss,hs,fs,falcon,host}_src. +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to + configure the USB pads used by the XHCI controller + +For Tegra124 and Tegra132: +- avddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- dvddio-pex-supply: PCIe/USB3 digital logic power supply. Must supply 1.05 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-usb-ss-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-usb-ss-supply: High-voltage PCIe/USB3 power supply. Must supply 3.3 V. +- hvdd-usb-ss-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- dvddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- hvddio-pex-supply: High-voltage PCIe/USB3 power supply. Must supply 1.8 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + +Optional properties: +-------------------- +- phys: Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names: Should include an entry for each PHY used by the controller. The + following PHYs are available: + - Tegra124: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2, + usb3-3 + +Example: +-------- + + usb@0,70090000 { + compatible = "nvidia,tegra124-xusb"; + reg = <0x0 0x70090000 0x0 0x8000>, + <0x0 0x70098000 0x0 0x1000>, + <0x0 0x70099000 0x0 0x1000>; + reg-names = "hcd", "fpci", "ipfs"; + + interrupts = , + ; + + clocks = <&tegra_car TEGRA124_CLK_XUSB_HOST>, + <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_SS>, + <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>, + <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>, + <&tegra_car TEGRA124_CLK_PLL_U_480M>, + <&tegra_car TEGRA124_CLK_CLK_M>, + <&tegra_car TEGRA124_CLK_PLL_E>; + clock-names = "xusb_host", "xusb_host_src", "xusb_falcon_src", + "xusb_ss", "xusb_ss_div2", "xusb_ss_src", + "xusb_hs_src", "xusb_fs_src", "pll_u_480m", + "clk_m", "pll_e"; + resets = <&tegra_car 89>, <&tegra_car 156>, <&tegra_car 143>; + reset-names = "xusb_host", "xusb_ss", "xusb_src"; + + nvidia,xusb-padctl = <&padctl>; + + phys = <&{/padctl@0,7009f000/pads/usb2/usb2-1}>, /* mini-PCIe USB */ + <&{/padctl@0,7009f000/pads/usb2/usb2-2}>, /* USB A */ + <&{/padctl@0,7009f000/pads/pcie/pcie-0}>; /* USB A */ + phy-names = "utmi-1", "utmi-2", "usb3-0"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-usb-supply = <&vdd_3v3_lp0>; + avdd-pll-utmip-supply = <&vddio_1v8>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + avdd-usb-ss-pll-supply = <&vdd_1v05_run>; + hvdd-usb-ss-supply = <&vdd_3v3_lp0>; + hvdd-usb-ss-pll-e-supply = <&vdd_3v3_lp0>; + }; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index ca164e71d..39acb084b 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -59,7 +59,6 @@ Example device nodes: interrupts = <0 205 0x4>; phys = <&hs_phy>, <&ss_phy>; phy-names = "usb2-phy", "usb3-phy"; - tx-fifo-resize; dr_mode = "host"; }; }; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 6a17aa85c..966885c63 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -4,6 +4,7 @@ Required properties: - compatible: should be one or more of - "generic-xhci" for generic XHCI device + - "marvell,armada3700-xhci" for Armada 37xx SoCs - "marvell,armada-375-xhci" for Armada 375 SoCs - "marvell,armada-380-xhci" for Armada 38x SoCs - "renesas,xhci-r8a7790" for r8a7790 SoC diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 86740d4a2..2c2500df0 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -16,19 +16,23 @@ al Annapurna Labs allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. +amazon Amazon.com, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. amlogic Amlogic, Inc. ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. +analogix Analogix Semiconductor, Inc. apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems arm ARM Ltd. armadeus ARMadeus Systems SARL +arrow Arrow Electronics artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. +aspeed ASPEED Technology Inc. atlas Atlas Scientific LLC atmel Atmel Corporation auo AU Optronics Corporation @@ -58,6 +62,7 @@ cnxt Conexant Systems, Inc. compulab CompuLab Ltd. cortina Cortina Systems, Inc. cosmic Cosmic Circuits +creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. cypress Cypress Semiconductor Corporation @@ -70,11 +75,14 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +dptechnics DPTechnics +dragino Dragino Technology Co., Limited ea Embedded Artists AB ebv EBV Elektronik edt Emerging Display Technologies eeti eGalax_eMPIA Technology Inc elan Elan Microelectronic Corp. +embest Shenzhen Embest Technology Co., Ltd. emmicro EM Microelectronic energymicro Silicon Laboratories (formerly Energy Micro AS) epcos EPCOS AG @@ -86,11 +94,13 @@ eukrea Eukréa Electromatique everest Everest Semiconductor Co. Ltd. everspin Everspin Technologies, Inc. excito Excito +ezchip EZchip Semiconductor fcs Fairchild Semiconductor firefly Firefly focaltech FocalTech Systems Co.,Ltd fsl Freescale Semiconductor ge General Electric Company +geekbuying GeekBuying GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. geniatech Geniatech, Inc. @@ -118,6 +128,7 @@ idt Integrated Device Technologies, Inc. ifi Ingenieurburo Fur Ic-Technologie (I/F/I) iom Iomega Corporation img Imagination Technologies Ltd. +inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation intel Intel Corporation @@ -141,6 +152,7 @@ lsi LSI Corp. (LSI Logic) lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +meas Measurement Specialties mediatek MediaTek Inc. melexis Melexis N.V. merrii Merrii Technology Co., Ltd. @@ -152,6 +164,7 @@ mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +mqmaker mqmaker Inc. msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. @@ -171,12 +184,15 @@ nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. olimex OLIMEX Ltd. +onion Onion Corporation onnn ON Semiconductor Corp. +ontat On Tat Industrial Company opencores OpenCores.org option Option NV ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies ORCL Oracle Corporation +oxsemi Oxford Semiconductor, Ltd. panasonic Panasonic Corporation parade Parade Technologies Inc. pericom Pericom Technology Inc. @@ -239,6 +255,7 @@ synology Synology, Inc. SUNW Sun Microsystems, Inc tbs TBS Technologies tcl Toby Churchill Ltd. +technexion TechNexion technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments @@ -247,10 +264,13 @@ toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. +tpk TPK U.S.A. LLC tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited +tyan Tyan Computer Corporation upisemi uPI Semiconductor Corp. +uniwest United Western Technologies Corp (UniWest) urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor @@ -259,6 +279,7 @@ via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation voipac Voipac Technologies s.r.o. +wd Western Digital Corp. wexler Wexler winbond Winbond Electronics corp. wlf Wolfson Microelectronics diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/video/bridge/anx7814.txt new file mode 100644 index 000000000..b2a22c28c --- /dev/null +++ b/Documentation/devicetree/bindings/video/bridge/anx7814.txt @@ -0,0 +1,40 @@ +Analogix ANX7814 SlimPort (Full-HD Transmitter) +----------------------------------------------- + +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter +designed for portable devices. + +Required properties: + + - compatible : "analogix,anx7814" + - reg : I2C address of the device + - interrupt-parent : Should be the phandle of the interrupt controller + that services interrupts for this device + - interrupts : Should contain the INTP interrupt + - hpd-gpios : Which GPIO to use for hpd + - pd-gpios : Which GPIO to use for power down + - reset-gpios : Which GPIO to use for reset + +Optional properties: + + - dvdd10-supply : Regulator for 1.0V digital core power. + - Video port for HDMI input, using the DT bindings defined in [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + anx7814: anx7814@38 { + compatible = "analogix,anx7814"; + reg = <0x38>; + interrupt-parent = <&gpio0>; + interrupts = <99 IRQ_TYPE_LEVEL_LOW>; /* INTP */ + hpd-gpios = <&pio 36 GPIO_ACTIVE_HIGH>; + pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>; + port { + anx7814_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 8dab6fd02..107280ef0 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -5,10 +5,12 @@ Required properties: - reg : Should contain WDT registers location and length - interrupts : Should contain WDT interrupt -Optional property: +Optional properties: - big-endian: If present the watchdog device's registers are implemented in big endian mode, otherwise in native mode(same with CPU), for more detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. +- fsl,ext-reset-output: If present the watchdog device is configured to + assert its external reset (WDOG_B) instead of issuing a software reset. Examples: diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt new file mode 100644 index 000000000..49485f831 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-dmt.txt @@ -0,0 +1,19 @@ +* Microchip PIC32 Deadman Timer + +The deadman timer is used to reset the processor in the event of a software +malfunction. It is a free-running instruction fetch timer, which is clocked +whenever an instruction fetch occurs until a count match occurs. + +Required properties: +- compatible: must be "microchip,pic32mzda-dmt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of source clk. Should be <&rootclk PB7CLK>. + +Example: + + watchdog@1f800a00 { + compatible = "microchip,pic32mzda-dmt"; + reg = <0x1f800a00 0x80>; + clocks = <&rootclk PB7CLK>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt new file mode 100644 index 000000000..f03a29a1b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/microchip,pic32-wdt.txt @@ -0,0 +1,18 @@ +* Microchip PIC32 Watchdog Timer + +When enabled, the watchdog peripheral can be used to reset the device if the +WDT is not cleared periodically in software. + +Required properties: +- compatible: must be "microchip,pic32mzda-wdt". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandle of source clk. Should be <&rootclk LPRCCLK>. + +Example: + + watchdog@1f800800 { + compatible = "microchip,pic32mzda-wdt"; + reg = <0x1f800800 0x200>; + clocks = <&rootclk LPRCCLK>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt new file mode 100644 index 000000000..b9512f1eb --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -0,0 +1,25 @@ +Renesas Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "renesas,r8a7795-wdt", or "renesas,rcar-gen3-wdt" + + When compatible with the generic version, nodes must list the SoC-specific + version corresponding to the platform first, followed by the generic + version. + +- reg : Should contain WDT registers location and length +- clocks : the clock feeding the watchdog timer. + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds +- power-domains : the power domain the WDT belongs to + +Examples: + + wdt0: watchdog@e6020000 { + compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&cpg>; + timeout-sec = <60>; + }; -- cgit v1.2.3-54-g00ecf