From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- Documentation/virtual/kvm/hypercalls.txt | 83 ++++++++++++++++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/virtual/kvm/hypercalls.txt (limited to 'Documentation/virtual/kvm/hypercalls.txt') diff --git a/Documentation/virtual/kvm/hypercalls.txt b/Documentation/virtual/kvm/hypercalls.txt new file mode 100644 index 000000000..c8d040e27 --- /dev/null +++ b/Documentation/virtual/kvm/hypercalls.txt @@ -0,0 +1,83 @@ +Linux KVM Hypercall: +=================== +X86: + KVM Hypercalls have a three-byte sequence of either the vmcall or the vmmcall + instruction. The hypervisor can replace it with instructions that are + guaranteed to be supported. + + Up to four arguments may be passed in rbx, rcx, rdx, and rsi respectively. + The hypercall number should be placed in rax and the return value will be + placed in rax. No other registers will be clobbered unless explicitly stated + by the particular hypercall. + +S390: + R2-R7 are used for parameters 1-6. In addition, R1 is used for hypercall + number. The return value is written to R2. + + S390 uses diagnose instruction as hypercall (0x500) along with hypercall + number in R1. + + For further information on the S390 diagnose call as supported by KVM, + refer to Documentation/virtual/kvm/s390-diag.txt. + + PowerPC: + It uses R3-R10 and hypercall number in R11. R4-R11 are used as output registers. + Return value is placed in R3. + + KVM hypercalls uses 4 byte opcode, that are patched with 'hypercall-instructions' + property inside the device tree's /hypervisor node. + For more information refer to Documentation/virtual/kvm/ppc-pv.txt + +KVM Hypercalls Documentation +=========================== +The template for each hypercall is: +1. Hypercall name. +2. Architecture(s) +3. Status (deprecated, obsolete, active) +4. Purpose + +1. KVM_HC_VAPIC_POLL_IRQ +------------------------ +Architecture: x86 +Status: active +Purpose: Trigger guest exit so that the host can check for pending +interrupts on reentry. + +2. KVM_HC_MMU_OP +------------------------ +Architecture: x86 +Status: deprecated. +Purpose: Support MMU operations such as writing to PTE, +flushing TLB, release PT. + +3. KVM_HC_FEATURES +------------------------ +Architecture: PPC +Status: active +Purpose: Expose hypercall availability to the guest. On x86 platforms, cpuid +used to enumerate which hypercalls are available. On PPC, either device tree +based lookup ( which is also what EPAPR dictates) OR KVM specific enumeration +mechanism (which is this hypercall) can be used. + +4. KVM_HC_PPC_MAP_MAGIC_PAGE +------------------------ +Architecture: PPC +Status: active +Purpose: To enable communication between the hypervisor and guest there is a +shared page that contains parts of supervisor visible register state. +The guest can map this shared page to access its supervisor register through +memory using this hypercall. + +5. KVM_HC_KICK_CPU +------------------------ +Architecture: x86 +Status: active +Purpose: Hypercall used to wakeup a vcpu from HLT state +Usage example : A vcpu of a paravirtualized guest that is busywaiting in guest +kernel mode for an event to occur (ex: a spinlock to become available) can +execute HLT instruction once it has busy-waited for more than a threshold +time-interval. Execution of HLT instruction would cause the hypervisor to put +the vcpu to sleep until occurrence of an appropriate event. Another vcpu of the +same guest can wakeup the sleeping vcpu by issuing KVM_HC_KICK_CPU hypercall, +specifying APIC ID (a1) of the vcpu to be woken up. An additional argument (a0) +is used in the hypercall for future use. -- cgit v1.2.3-54-g00ecf