From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- arch/arm/boot/dts/phy3250.dts | 202 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 202 insertions(+) create mode 100644 arch/arm/boot/dts/phy3250.dts (limited to 'arch/arm/boot/dts/phy3250.dts') diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts new file mode 100644 index 000000000..90fdbd77f --- /dev/null +++ b/arch/arm/boot/dts/phy3250.dts @@ -0,0 +1,202 @@ +/* + * PHYTEC phyCORE-LPC3250 board + * + * Copyright 2012 Roland Stigge + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "lpc32xx.dtsi" + +/ { + model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; + compatible = "phytec,phy3250", "nxp,lpc3250"; + #address-cells = <1>; + #size-cells = <1>; + + memory { + device_type = "memory"; + reg = <0 0x4000000>; + }; + + ahb { + mac: ethernet@31060000 { + phy-mode = "rmii"; + use-iram; + }; + + /* Here, choose exactly one from: ohci, usbd */ + ohci@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; + +/* + usbd@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; +*/ + + clcd@31040000 { + status = "okay"; + }; + + /* 64MB Flash via SLC NAND controller */ + slc: flash@20020000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + mtd1@00064000 { + label = "phy3250-uboot"; + reg = <0x00064000 0x00190000>; + read-only; + }; + + mtd2@001f4000 { + label = "phy3250-ubt-prms"; + reg = <0x001f4000 0x00010000>; + }; + + mtd3@00204000 { + label = "phy3250-kernel"; + reg = <0x00204000 0x00400000>; + }; + + mtd4@00604000 { + label = "phy3250-rootfs"; + reg = <0x00604000 0x039fc000>; + }; + }; + + apb { + uart5: serial@40090000 { + status = "okay"; + }; + + uart3: serial@40080000 { + status = "okay"; + }; + + i2c1: i2c@400A0000 { + clock-frequency = <100000>; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + uda1380: uda1380@18 { + compatible = "nxp,uda1380"; + reg = <0x18>; + power-gpio = <&gpio 0x59 0>; + reset-gpio = <&gpio 0x51 0>; + dac-clk = "wspll"; + }; + }; + + i2c2: i2c@400A8000 { + clock-frequency = <100000>; + }; + + i2cusb: i2c@31020300 { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + }; + + ssp0: ssp@20084000 { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <1>; + cs-gpios = <&gpio 3 5 0>; + + eeprom: at25@0 { + pl022,interface = <0>; + pl022,com-mode = <0>; + pl022,rx-level-trig = <1>; + pl022,tx-level-trig = <1>; + pl022,ctrl-len = <11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + + at25,byte-len = <0x8000>; + at25,addr-mode = <2>; + at25,page-size = <64>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + }; + }; + + sd@20098000 { + wp-gpios = <&gpio 3 0 0>; + cd-gpios = <&gpio 3 1 0>; + cd-inverted; + bus-width = <4>; + status = "okay"; + }; + }; + + fab { + uart2: serial@40018000 { + status = "okay"; + }; + + tsc@40048000 { + status = "okay"; + }; + + key@40050000 { + status = "okay"; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led0 { /* red */ + gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */ + default-state = "off"; + }; + + led1 { /* green */ + gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */ + linux,default-trigger = "heartbeat"; + }; + }; +}; -- cgit v1.2.3-54-g00ecf